Home
User Manual
Contents
1. GRADE CHASSIS Stainless steel end and bottom plates provide a stunning finish coupled with environmental protection RCA LINE OUT A pass through RCA output enables linking of multiple amplifiers for enhanced system performance FEATURE OVERVIEW Control Descriptions 004 POWER SELECTOR 0 0 _ GFF ip mp Hz 160Hz 40Hz 600Hz OdB 18d8 20Hz SSHz 8V 03V I 1 Power And Status LEDs This shows if the amplifier has been correctly powered up and if any faults are pre sent 2 Crossover Selector Set the appropriate mode of operation The 3 positions available are OFF LP and HP 3 Low Pass Set the crossover switch 2 to LP when a subwoofer is connected Ensure the crosso ver frequency is set at 100Hz or below this feature is designed to filter all mid to high frequencies that only FULL RANGE speakers should produce NOTE Failure to do so could result in speaker damage 4 High Pass Set the crossover switch 2 to HP and turn this control to 65Hz or above when using speakers smaller than 6 this feature is designed to filter all low bass frequencies that only SUBWOOFERS should produce NOTE Failure to do so could result in speaker damage 5 Bass Boost This is a variable control to increase the bass boost at 45Hz from O 18dB of gain adjust to suit 6 Subsonic Filter This is a variable control filters out all Sub Bass Frequencies below the set point at 18dB octave 7 Level This allo
2. 010 Trouble Shooting Problem Cause Solution Fuse at battery blown 3 Y Replace with correct type and rated fuse Power LED Or not installed eck that the ground wire power wire and the remote noe ON A Check that the ground wire p dth t mproper connections Wires are connected to the correct terminal Fuse blown Replace with correct type and rated fuse Amplifier too hot Move the amplifier into a more ventilated area tatus LED 7 S ON Check that there are no speaker wires shorted to any Speaker wires shorted other wire and also check if any wire is shorted to ground Int If af Disconnect all wires except ground power and remote Then turn the amplifier ON if the protection light is still ON then return for service nternal maltunction plif f pi g fe F Specifications Signal to Noise Separation Input Sensitivity LP Variable Crossover HP Variable Crossover Variable Bass Boost Variable Subsonic Filter Input Impedance Damping factor T H D Fuse Ratings Dimensions mm gt 95dB gt 60dB 300mV 8V 40Hz 160Hz O 18dB octave 40Hz 600Hz O 12dB octave O 18dB 45Hz 20Hz 55Hz O 18dB octave 20k Q gt 200 0 05 1x 25A 229 W x 296 L x 53vz H 12 6 Volt power output specification 50 Watts RMS x 2 40 1 THD N 96 Watts RMS x 2 20 1 THD N 160 Watts RMS x 1 O 40 Bridged 1 THD N 14 4 Volt power output specification 65 Watts RMS x 2 40 1 TH
3. D N 100 Watts RMS x 2 20 1 THD N 200 Watts RMS x 1 40 Bridged 1 THD N FUSIONENTERTAINMENT COM
4. MS AM402 MARINE AMPLIFIER User Installation Manual Contents Feature Overview 2 2 cc ccc eee ee eee Pg Control Descriptions erres sees seas tees obar 40000 Os Pg Installation eos da eee ne ert aie da Pg Connections i s hiss SEs oo She se ek Pg Inputs and Gain Setup cee ee eee eee eee Pg Single Channel Installation ooooooooo Pg Two Channel Installation Power Cable Calculator Pg Trouble Shooting Specifications Pg 1 RECORD YOUR PRODUCT DETAILS HERE MODEL NUMBER DATE OF PURCHASE AFFIX RECEIPT HERE Feature Overview e 2 Ohm Stable MOSFET Amplifier Design e Variable Bass Boost 0 18dB e Variable LP and HP Electronics X OVER 18dB octave e 4 Gauge Power and Ground Connections e Nickel Plated Audio Input and Output RCA Connections e Nickel Plated RCA Output for multi amp Installations 2 OHM STABLE STEREO Provides the option of connecting an extra pair of speakers in parallel 2 per channel at 2 Ohms A total of 8 speakers MARINE GRADE CONNECTIONS Nickel plated RCA connectors and stainless components improve signal flow for optimum output CLASS AB DESIGN The 500 Watt 2 Ohm stable per channel design ensures clean and powerful amplification of the input signal enough to rock the boat CONFORMAL COATED CIRCUITRY Provides added protection from salt air and moisture to ensure maximum product life MARINE
5. ect the performance and reliability of your FUSION amplifier For maximum performance we recommend you have your new FUSION amplifier installed by an authorised FUSION dealer Our highly skilled dealers have vast knowledge of our products and their installation techniques are necessary to unleash the high performance capabilities of your amplifier If you decide to connect the amplifier yourself it is important that you read this manual carefully and throughout before starting Once you have finished reading and you still have questions regarding installation we recommend your FUSION dealer Connection FUSION amplifiers are designed to work within a 10 to 16 volt DC range Before any wires are connected the vessel s electrical system should be checked for correct voltage supply with the help of a voltmeter First check the voltage at the battery the voltmeter should read between 12 and 13 8 Volts If your vessel s electrical system is not up to these specification we recommend having it checked by an auto electrician before any further installation Once the vessel is checked make certain the correct cable size is used We recommend using the following cables calculator diagram on page 9 to calculate the correct power cable for your application Power FUSION amplifiers should be wired directly to the battery using the appropriate sized cable Start at the vessels battery and run the power cable through to the amplifier FUSION recommends t
6. he use of grommets when passing the power cable through any metal wall to avoid sharp corners or sharp body parts that may easily cut through the insulation on the cable Avoid running the power cable over engine components The use of an inline fuse or circuit breaker is a must this will prevent the risk of a potential fire caused be a short in your power cable Connect the fuse holder or circuit breaker as close to the battery positive terminal as possible Use a fuse or circuit breaker of equal value as that found on the chassis of your FUSION amplifier You may now connect the cable to the battery but remember to leave the fuse out or circuit breaker off until all other cable connections are made Ground When grounding your FUSION amplifier use the same gauge cable for ground as you did for the power Secure the ground cable to the appropriate ground point now its time to connect the power and ground cables to the amplifier Cut both cables to length Use a hex type screwdriver to loosen the 12V and the GND connections on the amplifier Terminate the ground first and then the 12V and please make sure that you terminate them into the correct terminals Then tighten the screws down securely Speaker Load Keep in mind FUSION AM series amplifiers are high power amplifiers and not high current amplifiers In other words they require a minimum impedance of 2 ohms STEREO and 4 ohms bridged MONO to operate trouble free Too low of an im
7. in three simple steps 1 Turn the LEVEL control on the amplifier to minimum 2 Turn up the head unit and adjust to 2 3 maximum volume ensuring that the BASS and TREBLE are set to zero 3 Adjust the LEVEL control until the desired volume is achieved without audible dis tortion Remember the gain control is not a volume control Ignoring the three steps above may leave you with damaged speakers and or a damaged amplifier Single Channel Installation X OVER A UBSONIC LEV POWER SELECTOR cH suus 0000 OFF ip mp 40Hz 160Hz 40Hz 600Hz OdB 18d8 20Hz SSHz 8V 03V Power Cable Calculator O CONNECTION Total Amperage 0 4ft 4 7ft 7 10ft 10 13ft 13 16ft 16 19ft 19 22ft 22 28ft 0 20 14 12 12 10 10 8 8 8 20 35 12 10 8 8 6 6 6 4 35 50 10 8 8 6 4 4 4 4 50 65 8 8 6 4 4 4 4 2 65 85 6 6 4 4 2 2 2 0 85 105 6 6 4 2 2 2 2 0 105 125 4 4 4 2 0 0 0 0 125 150 2 2 2 0 0 0 0 0 The above chart shows cable gauges to be used if no less than a 0 5 volt drop is acceptable If aluminium wire or tinned wire is used the gauges should be of an even larger size to compensate Cable gauge size calculation takes into account terminal connection resistance 1 Metre 3 28 Feet Two Channel Installation n hi gt A ida 5 OV BASS BOOST SUBSONIC LEVE POWER SELECTOR C STATUS O O OFF LP Hp Hz 160Hz 40Hz 600Hz OdB 18dB 20Hz SSHz 8V 03V INSTALLATION
8. installation as damage could result 13 Fuse Please ensure the correct type of fuse is fitted as specified in this manual PLEASE NOTE the MS AM402 has 1x 25A fuse 14 Speaker Output See channel installation diagrams in this manual for correct speaker connection pati 006 INSTALLATION Installation lt o 3 chi 5 o E Appropriate mounting is very important for the prolonged life expectancy of any amplifier Select a location that allows enough space so sufficient airflow is maintainable and a location that provides protection from moisture Keep in mind that an amplifier should never be mounted upside down Upside down mounting will compromise heat dissipation through the heatsink and could engage the thermal protection circuit Excessive heat will shorten your amplifiers life To maximise heat dissipation be sure to leave at least 2 5 of clearance around the amplifier If space is of the essense and the amplifier must be mounted in an enclosed or restricted area a small 3 inch fan should be used in correspondence with a duct so the heat can flow past the Heatsink To avoid scratching your new FUSION amplifier pre drill the mounting holes with either a 3mm or 9 64 diameter drill bit and use the screws supplied in the accessory kit Be sure to investigate your mounting area thoroughly to avoid electrical wires vacuum lines or fuel lines Installation Options The quality of installation will aff
9. pedance could send your FUSION amplifier into protection mode and or damage the amplifier Remote Turn on This terminal must be connected to a switched 12V source Typically remote turn on leads are provided at the head unit which will turn on and off the amplifier If the head unit does not have a remote turn on lead then a power antenna wire can be used If neither of these leads are present on the head unit then a switched 12V supply must be used like the ACC 12V Run a minimum of 18 gauge wire from the amplifier location to the source of the switched 12V lead Connect the source remote output to the wire Go back to the amplifier and cut the wire to length Loosen the screw terminal marked REM on the amplifier using a hex type screwdriver Slip the wire into the connector and tighten the screw securely CONNECTION INSTALLATION Inputs Gain Setup Low Level Inputs Be extra careful with your RCA interconnects Hiss engine noise and fan noise can easily be picked up through RCA cables if run incorrectly Avoid running your RCAs near large wire looms and electric fans if possible Run your RCA cables on the opposite side of the power cable Be sure to check for correct balance Red is right and black or white is left Level Control On the amplifier is the LEVEL control this control allows you to match the input level of the amplifier to the output level of your head unit Matching the input can be accom plished
10. ws level adjustment of the input signal Use this control to correctly match the head unit to the amplifier To set this control correctly turn the amplifier level to MIN and the head unit to 3 4 volume with the BASS and TREBLE on zero then slowly turn up this amplifier level control towards the MAX end of the control NOTE If the sound becomes distorted turn this control down 8 RCA Input Connect these RCA connectors to the LOW LEVEL output connection from the head unit 9 RCA Output Use these RCA Output connectors to connect to a secondary amplifier This output is a PASS THRU connection derived from the RCA input connector so the signal level and frequency response are the same as the original input signal 10 Ground Connection Connect directly to a suitable ground point via a 4 gauge power cable NOTE This is to be the first wire to connect Damage could result if this is not done 11 Remote Connection This input is for turning the amplifier on and off This requires a switched positive 12V to power ON the amplifier this can be found on the rear of the head unit in the form of an electric antenna output or a remote on output If not available you can wire to a switched 12V supply 12 Power 12V Connection This must be connected to the battery positive terminal via a 4 guage power cable and with an inline fuse or circuit breaker at the battery end NOTE This is to be the last wire to connect up during
Download Pdf Manuals
Related Search
Related Contents
intext:Bedienungsanleitung filetype:pdf User Manual in English Bluetooth GPS Receiver GPS Firmware A1037-A WC50D - Oomipood 電池式デジタル温圧計 TEMPRESS DTPⅢシリーズ 取扱説明書 B&C Speakers Hf Compression Drivers DE 25 User's Manual 乳母車の認定基準及び基準確認方法 Copyright © All rights reserved.
Failed to retrieve file