PROMI 1000 - CST SECURITE
Contents
1. Edition 10 2003 I PRESENTATION DU PRODUIT A Product presentation Input voltage 12V AC DC 12 digit keypad with LED visual indicator EPROM memory storage Date and hour saving with 3V CR2032 battery 1000 programmable proximity badges and Pin codes 1000 event stored in memory buffer Up to 16 holidays Removable memory unit RS232 output Event thermal printing Printing of all events and configuration Print badge and code list Printer with or without DTR signal MTP640 Kyoline printer recommended Capability to connect an external reader up to 50 meter Anti pass back PROMI 1000 to exit and reader to enter 1 relay output RT contact 3A 125V 1 alarm relay output N O contact 3A 125V 3 operating modes Mode 0 Badge and Pin code Mode 1 Badge only Mode 2 Badge or Pin code 3 time zones to operate the 3 operating modes 5 digit programmable master code Proximity readers and keypad lockout during 2 minutes after 3 invalid Pin code badge Buzzer for audible signal 1 request to exit input Door contact input Minimum distance of 60 cm between the controller and the reader Edition 10 2003 B Factory Default Values Operating mode 0 badge and Pin code Door open time 1 second Alarm time delay 00 alarm disabled Key in keypad time 10 seconds Master code 12345 No time zone No Holiday Anti pass back disabled DTR signal on for printer Programming time 2 minu2. Setting Date and Hour The PROMI 1000 has a buit in clock calender with time and date The clock must always be powered by the 12V power supply or the 3V CR1225 battery The battery is used only in case of power failure 17
3. after the alarm time delay the alarm relay is activated and the red LED lights on Closing back the door will deactivate the alarm relay and the LED start flashing orange Latched output The alarm time delay begins only when the door stays open after ordering the closing by present ing back the badge or pressing on the request to exit button the alarm relay is activated and the red LED lights on Closing back the door will deactivate the alarm relay and the LED flashes or ange Edition 10 2003 O T Note 1 During an alarm the reader and the request to exit are enabled 2 To cancel the alarm go to Menu 03 in programming and enter OO Events Quand l alarme est command e forced door open door ajar or lockout alarm the following messsages are printed on the event report Alarm and Alarm end with the day and hour of the event Date Heure Mode Alarm 25 09 03 17 38 2 Alarm cleared 25 09 03 17 44 2 Memory The memory unit on the PROMI 1000 can be removed The time outputs the schedules the holi day periods the badges the Pin codes and the events are stored in the memory unit All the data on the memory Anti pass back To start the anti passback mode go to menu 08 The PROMI 1000 must used as an exit unit and the remote reader as the entry reader It is important to present the badge on the entry reader and on the exit reader The access is granted only when the badge was presented on the exit reader
4. aes ere estates 6 B Main TU iscecesic sees e e canes bac vac E e E E 6 C Menu 00 Program badges and Pin codes 6 D Menu 01 Operating MOde ga ccciccccscszssncsaizessvezetedessthoateinteaeneietioereaetiaensetnesautenteasiomiduend 7 E Menu 02 Door release time ccc ccccsscsssssssssecsscsssssecsesssssecsessssnssesssssssecsessssneceesssssseeseessseeeeeeen 8 F Menu 03 Alarm time output sie tccitscateslueadsiebcendoun maison bonnlasionackaoks 8 G Menu 04 Master Code wae ceccccssssesssosssusesccsssnsssscssssusessesssiusssessssuseesesssuusesssssuseseesssueeessesssueeeeeassnes 8 H Menu 05 Setting date and hour sccscc ccccnocesscexcnevaverintscesvivexossniedsenivdvivictndedvindsdsiviv sdeiasedciveniavendeis 9 l Menu 06 Schedules ss ssssssssssissssisssrisssirsssrrsssrirssnsrsserrsssrrssstrssstrsnsntrsttrssnnrsnnnrnnntrsnntrnntnrntnrnnns 9 Je Menu 07 HOldayS sepsisni o E a A 10 K Menu 08 Anti pass back s sss1ss11s11s11511511sstsstrsstrsstrsstrsstrsnntsnntsnntrnntrnntrntrnnrsnntsnneannrrnnnrnnnrnt 10 L Menu 09 Printer and event ech cae os eeeesstctercteareseces seen eantenomnanaeeaceunemecemeael 10 M Menu 10 Badge enrolment unit nn ccasssssssssecsessssnesssssssssseseesssnsessssssneeessesssneeess 12 N Menu 11 Delete Schedules cccssssssssssssscsssssssscsscsssssscssssssnsessssssnsecsessssnscsessssnseeseesssueees 13 O Menu 12 Delete Noida ys csscccsccctnnces an cea a 13 P Menu 13 Setting accesses during the Nol
5. 30 stop time 22h50 Monday to Friday Enter 09 30 22 50 8 Press Then press back to ER The PROMI 1000 returns to the main menu Edition 10 2003 10 J Menu 07 Holidays Press 07 to enter in the holidays menu 16 different holidays can be programmed enter the a holiday number from 01 to 16 Then enter the day and month for this holiday Example 25 October enter 25 10 The LED lights on in green va Press to go back to the Main MENU The PROMI 1000 returns to the main menu o Then press OR Enter another holiday Menu 08 Anti pass back Press 08 to enter in the anti pass back menu Press O to deactivate the anti pass back mode Wait 5 seconds for the complete deactivation Press 1 to activate the anti pass back The PROMI 1000 must be used as the exit reader and the remote reader as the entry reader The LED lights on in green Q Press to go back Then press to the Main MENU The PROMI 1000 returns to the main menu o Menu 09 Printer and event Press 09 to enter in the printer setup and event printing menu Press Oto delete all the events from the controller R then press to confirm wait 15 sec The LED lights on in green Then press lacie serdar The PROMI 1000 returns to the main menu oO OR Press Lto print all the events stored in the memory buffer Q then press to confirm Q Edition 10 2003 To stop the printer at any time keep pressing on the O key until the LED lights on in g
6. Edition 06 2004 G0301FRO222V01 CDVI PROMI 1000 31 av du Gal Leclerc agile STAND ALONE ACCESS CONTROL SYSTEM Fax 33 0 48 91 21 21 www cdvi com INSTRUCTION This device comes with a varistor The varistor must be connected on the strike terminal electro magnet operated by the device If this product operates more than one strikes each of them should have a varistor The varistor controls the overload produced by the strike coil back emf O z lt lt cc O lt O O z z If you are using a Shear Lock electromagnetic lock it is recommended to use a sepa rate power supply than the one connected to the PROMI 1000 Edition 10 2003 PROMI 1000 USER MANUAL l PRESENTATION DU PRODUIT c cccsscsctassceedauneisieeiadesanadadiotanaiiunnauniaceianinunianaiatne 3 A Product presentation s ssssssssessssssrssorrsestrssstrsssttrssotrsentrssotrsnntrsnttrsentrsnotrsnotrsnotrsnnttrtntrsnotrsnntrsn ntre at 3 B Factory Default Values iin ccssssssssssssssssssssssusssssssumessessssnsssssssumsssesssnussssssssuessesssuueeseessseeeeseen 4 Rey PU OGRA Sers sA aeea ea ae alae a a aee 4 DAREV LESO AT E 4 E Current COnSUMDLION o 2ccnacenadanaauiacedannnnnananenadannannacaunamanemmanetod 4 F Recommended printer scant acct anst nada eee tnnt 4 AAOC 1 els ek eRe ee eRe eer ere ee er em Irn een ten erm ema amen amen net em rt 6 A Colors and audible signals ws ccsscis tie teat een eee eee tcc
7. adge and or PIN code are entered the PROMI 1000 reader and the second prox imity reader are locked out during 2 minutes and the alarm relay is activated 2 audible beeps sound when the badge PIN code are not valid The LED lights on in red during the time of the lockout The LED flashes in orange when the lockout is finished Event printing When a badge is presented or a Pin code is entered the user number code of badge or Pin Code date hour and operating mode are printed User number Code of badge Date Heure Valid badge Badge 022DC567 25 09 03 17 38 2 Invalid badge Badge 0236AD7C 25 09 03 17 40 2 The last 8 digit of the code of the badge are printed 1000 events are stored in the memory buffer of the controller The 1001 event replaces the first one Door contact Alarm The tamper switch activates the relay of the alarm when the front panel is removed If the alarm time delay is different to 00 the door monitoring door ajar or door forced open is enabled When the door is opened without being activated by the request to exit button or a badge the alarm relay is activated after 1 second and the red LED lights on forced open door When the badge or the request to exit button are used to open a door if the door stays open the open contact will trigger the alarm relay according to the door relay output Momentary output The alarm time delay begins at the end of the door release time If the door is maintained open
8. aster code Press 04 to enter in the master code menu Enter the new 5 digit master code The LED lights on in green Q Then press il The PROMI 1000 returns to the main menu or Edition 10 2003 H Menu 05 Setting date and hour Enter 05 to enter in the date and hour menu Enter the hour and minutes then the day month year and the week day Q Week day Monday enter 1 Tuesday enter 2 Wednesday enter 3 Thursday enter 4 Friday enter 5 Saturday enter 6 Sunday enter 7 Example 09h26 02 September 2003 Tuesday Enter 09 26 02 09 03 2 Then press a ae The PROMI 1000 returns to the main menu o Menu 06 Schedules Press 06 to enter in the schedule menu Each operating mode can be associated with one schedule Enter the schedule number of the operating mode e Ofor the schedule of the operating mode O 1 for the schedule of the operating mode 1 2 for the schedule of the operating mode 2 Enter the hour and the minutes for the start time then the hour and the minutes for the stop time And the week day Q Week day Everyday enter O Monday enter 1 Tuesday enter 2 Wednesday enter 3 Thursday enter 4 Friday enter 5 Saturday enter 6 Sunday enter 7 Monday to Friday enter 8 Saturday and Sunday enter 9 Example start time 9h
9. ber or press on twice Q to delete the badge and Pin code Then present a badge in front of the PROMI 1000 or external reader Enter the 5 digit Pin code o OR Press to skip the pin code o Another search is launch to select an available user number If the printer is connected during the programming then the user number code of badge and Pin code are printed The last 8 digit of the code of the badge are printed Menu 01 Operating mode Press 01 to enter in the operating mode menu Press O to select Badge amp Pin code operating mode The LED lights on in green Q OR Press 1 to select badge only operating mode The LED lights on in green Q Edition 10 2003 OR Press 2 to select badge OR Pin code operating mode The LED lights on in green Q Then press Miisa ar The PROMI 1000 returns to the main menu OL Menu 02 Door release time Enter 02 to enter in the door release time menu Enter the time in seconds from O1 to 99 for a momentarily output or OO for a latched output The LED lights on in green Q Press f Then press back to MENU The PROMI 1000 returns to the main menu oL Menu 03 Alarm time output Enter 03 to enter in the alarm time output menu Enter the time in seconds per 10 seconds O1 to 99 and OO to disable the alarm O1 pour 10s et 99 pour 990s The LED lights on in green Q Press Then press back to MENU The PROMI 1000 returns to the main menu oL Menu 04 M
10. he user number 000 to 999 The LED lights on in red Q 13 Edition 10 2003 Press 1 to authorize the access for the selected user number cardholder or press Oto deny ac cess for the selected user number during the holidays The LED lights on in green Press to go back oL Then press to the Main MENU The PROMI 1000 returns to the main menu OR Press to authorize the access to all the cardholder o Press to confirm and wait 5s until the new configuration is set for all the cardholder The LED lights on in green OR Press to deny access to all the cardholder during the holiday periods or Press to confirm your choice and wait 5 seconds until the new configuration is set for all the cardholder The green LED lights on Press t k Then press tothe dat ata The PROMI 1000 returns to the main menu o Exit from programming You must be in the main menu to exit from programming press Once you exit from programming the PROMI 1000 is on stand by the LED flashes in orange lll OPERATING INSTRUCTIONS A 14 The key in time between two digit is set at 10 seconds Behond that time the data computed is canceled Reset Place the ST1 jumper in 2 3 position The LED flashes in green during 5 seconds The default master code is restored to 12345 Edition 10 2003 The LED flashes in red and a beep is emitted Remove the jumper from 2 3 position then the unit goes back to stand by mode OR Keep the
11. i days ccsssesscssssseccssssseeessesssneeess 13 Q Exit from DrOgh ams cx cnce tert anean Madea ede 14 Ill OPERATING INSTRUCTIONS sxsc onc s sccxcasrz czccodidesvecdeienecesedsdiceltecasasiedcdattenenideinecdtinasdmanaununcateeddes 14 Pee Te aan EE E E AAEE 14 B Operating MOdeS sss sssisssiisssiisssiiissirisssrisssrissrissstirssrtrsstnrsserrnsntisnstrsnstirntnrnnnrnnnnrsnntrsnnn rnnt nraans 15 C LOCKOUT eree a E A sense EEE 15 D Event printing s ssssississsisssirssrirsssrisssrisssrissstissstrrssttrsstnrsstisstisstrssstirstnrsntnrsnetrnan rnnt rnn are rr 16 E Door contact TIN vacastcncc ccdexcacsesazvecerdenecossdsrcacizdonsaaintosrasiedeaeneseisitesitlnnastiasitiamtinaddemnce 16 Fe MEMO y respissopngusnontonnosoninmann ii riii eisi reii bisik iniuiiiknit 17 Sig T AL E oT Eca OAC ce ateateeecccteceten tina cctiandaitetet actiactecttiaes asta acteaa diets adamantane 17 H Setting Dat and OU sorseniesossuoiosionsnonssonn nnani nii 17 V WIRING DIAGRAM s ccsss siccecsrcececatdcentedcwedaaudauudiacsidrecttdaadcertaditaxdutudeadudetadceanccereae 20 VI TEMPLATE ssc ae Nea t nAn E ra knra EEAS EEAS AEEA AE AAE AEAEE AAEE SEEE rannan n rran n nananana 23 It is recommended to read the user manual to familiarize yourself with all the features and the operating instructions An synoptic is available at the end of the user manual The synoptic is usefull to have a general overview on the complete programming instructions
12. jumper on 2 3 position to reset the badges pin codes schedules and holidays from the PROMI 1000 memory The LED flashes in red during 5 seconds then the LED lights on in red during the reset The LED starts flashing in orange when the reset is completed and a beep is emitted Remove the jumper from 2 3 position to go back to stand by mode OR Keep the jumper on 2 3 position to reset the events The LED flashes in orange during 5 seconds then lights on in orange during the reset The LED lights off when the reset of all the events is completed Remove the jumper from 2 3 position to go back to stand by mode B Operating modes Mode 0 badge and Pin code Present the badge in front of the PROMI 1000 unit A beep is emitted when the badge is valid Enter the 5 digit pin code If the Pin code is valid the relay is activated and the access is granted Two beeps are emitted to indicate that the badge or Pin code are invalid Mode 1 badge only Present the badge in front of the PROMI 1000 unit The access is granted if the badge is valid Two beeps are emitted to indicate that the badge is invalid Mode 2 badge or Pin code Present the badge in front of the PROMI 1000 unit The access is granted if the badge is valid Two beeps are emitted to indicate that the badge is invalid OR Enter the 5 digit Pin code If the Pin code is valid the access is granted C Lockout 15 Edition 10 2003 16 After 3 incorrect b
13. reen and a beep is emitted At the end of the printing the a message END PRINTING appears on the report The LED lights on in green Q Press to go back Then press tothe Main MENU OR The PROMI 1000 returns to the main menu oL Press 2 to print the configuration report of the PROMI 1000 control unit Mod 2 Touv Ols Talarm 640s Mait 12345 Mod Operating mode DTR off Pass back on Touv door release time Talarm alarm output time Schedule mode 0 12 56 14 23 0 Schedule mode 1 13 19 15 45 3 Master Master Code Schedule mode 2 19 12 22 47 7 Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday Holiday The LED lights on in green Q OR 11 Edition 10 2003 12 Press 3to print all the code of badge and Pin code To abord the printing report keep pressing on the Okey until the LED lights on in green and a beep is emitted User number Badge 022DC567 12458 023ABD99 54831 023AA1CO 023A9305 89657 02397F8A 55632 Only the last 8 digit of the code of the badge are printed on the report The LED lights on in green i pah a The PROMI 1000 returns to the main menu o Then press OR Press 4if the DTR signal is off on the printer The LED lights on in r Q OR Press 5 if the DTR signal is on the printer printer on line The LED lights on in green Q Press to go back Then press to the Main MENU The PROMI 1000 return
14. s the LED color O for orange G for green and R for red the digit represents the number of beep emitted The LED turns green and the 1 beep is emitted The LED turns Red and 1 beep is emitted Main menu Important Refer to the one page programming Enter the master Enter the master code twice 12345 default The LED turns on to orange code twice and 2 audible beeps are emitted A time delay of 2 minutes is set before the main menu is being shut down Once in the main menu the LED lights on in orange Enter the 2 digit number of the menu to select a menu from 00 to 13 Q Once you enter in the menu the LED lights in red Press on the to exit from programming Menu 00 Program badges and Pin codes Press 00 to enter in badge amp Pin code programming menu The badges and Pin codes are stored in a slot pigeon hole defined as a user number Once in the badge programming menu an automatic search is launch to select the next available user number Once a free user number is selected the LED lights on in Green Q Edition 10 2003 Present the badge in front of the PROMI1000 or in front the external reader o nal reader see Menu 10 OR Select a user number enter the 3 digit user number from 000 to 999 If the user number is available the LED lights on in Green Q present the badge in front the PROMI 1000 or in front of the external reader If the user number is not available enter another user num
15. s to the main menu oL Menu 10 Badge enrolment unit Press 10 to enter in the badge enrolment unit menu The default badge enrolment unit is the controller built in reader Press O to select the controller built in as the badge enrolment reader press 1 to select the re mote reader as the badge enrolment reader Edition 10 2003 The LED lights on in green Press to go back Then press tothe Main MENU The PROMI 1000 returns to the main menu oO To program badges and Pin code selec t Menu 00 The built in reader of the controller is set back as the default badge enrolment unit once you exit from programming Menu 11 Delete schedules Press 11 to enter in the delete schedule menu Enter the schedule of the operating mode to delete R Oto delete schedule of operating mode O 1to delete schedule of operating mode 1 2 to delete schedule of operating mode 2 Press on twice to delete the schedule Press to go back Then press to the Main MENU The PROMI 1000 returns to the main menu Menu 12 Delete holidays Press 12 to enter in the delete holiday menu Enter the holiday number to delete from Olto 16 Press twice to delete the holiday The LED lights on in green Q Press to go back to the Main MENU The PROMI 1000 returns to the main menu Then press OR Enter another holiday number Menu 13 Setting accesses during the holidays Press 13 to enter in the setting holiday menu Enter t
16. ts C Audible signals 1 short beep keypad digit key pressed 1 long beep Access granted or valid data computing 2 short beeps Start or exit from programming or invalid badge read 4 short beeps Error computing data or badge already programmed D Visual signals LED color En lecture En programmation Orange flashing Stand by Error computing data Orange Main menu Green Access granted Validate computing data Red Alarm Validate menu E Current consumption 200 mA F Recommended printer MTP 640 KYOLINE KYOSHA Paper thermal black printer width 112 mm diameter 38 mm Edition 10 2003 reference TP50XSE2C RS232 with DTR signal printer on line 9600 bauds Dip switchs set up on the printer 1 start ON Parity even 12345 67 8 1 stop IBM mode 40 characters CR skip line DTR signal high printer on line low printer off line Terminal Brown Back side Paper error When paper roll is finished the printer LED flashes fast The data is stored in the memory buffer of the printer until it is full Place another paper roll in the printer and press on the feed button until the paper is placed properly and put back the top cover of the printer the LED flashed slowly press promptly on the feed paper button the printer starts printing the data stored in its buffer The LED stops flashing Edition 10 2003 ll PROGRAMMING A Colors and audible signals The letter in bolt represent
Download Pdf Manuals
Related Search