Home

Emulex Drivers for Solaris FC version 2.75h User Manual

1. cccececeeeseteeeeeees 39 Fibre Channel Fabric FCF Events ccccceeeeeeeeeeeeeeennneeeeeeeeseteneeeeeees 41 Emulex Drivers for Solaris User Manual Page iv gt EMULEX Introduction This document provides the information needed to use the Emulex Fibre Channel FC out of box drivers for Solaris StorEdge SAN Foundation Software SFS which is part of the SFS Leadville stack The module name for the out of box Emulex FC driver for Solaris SFS is elxfc You should be familiar with Solaris and have access to standard system information before installing or using this driver For the FC driver familiarity with Oracle Storage SFS and FC is essential Important Considerations New in This Release e Support for Solaris 11 e FC driver supports Solaris 11 NPIV virtual ports Known Issues See the product release notes for the latest information Driver Information FC Prerequisites One of the following operating systems must be installed Solaris 10 SPARC e Solaris 10 x64 and x86 Solaris 11 SPARC e Solaris 11 for x64 Compatibility For a list of adapters that are compatible with the Emulex FC driver refer to the driver s Downloads page on the Emulex website For compatible firmware versions see the Downloads page for the specific adapter Emulex Drivers for Solaris User Manual Page 1 gt G EMULEX Installing the Drivers Installing the Out of Box Drivers for Solaris 10 and 11 1 Login as
2. Note If you want to override a driver parameter for a single driver loading session you can specify it as a parameter to the modload command For example modload kernel drv elxfc automap 0 for 32 bit platforms or modload kernel drv sparcv9 elxfc automap 0 for 64 bit platforms Emulex Drivers for Solaris User Manual Page 6 Table 1 FC Configuration File Parameters gt G EMULEX Property Name Default Min Max Activation Comments ackO Adapter reset Uses ACKO for class 2 If ACKO is 1 the adapter attempts to use ACKO when running Class 2 traffic to a device If the device doesn t support ACKO then the adapter uses ACK1 If ACKO is 0 only ACK1 is used when running Class 2 traffic adisc support Dynamic Sets the driver level support for the FC ADISC login I O recovery method 1 Partial support Flushes I O s for non FCP2 target devices at link down 0 No support Flushes active I O s for all FCP target devices at link down 2 Full support Holds active I O s for all devices at link down assign alpa 0x00 0x00 Oxef Link reset This property is only valid if the topology is set to loop A 0x00 setting means no preference If multiple adapter instances on the same host are on the same loop set this property differently for each adapter console errors 0x00000000 0x00000000 OxFFFFFFFF Dynamic Verbose mask for error messag
3. MSG_ID 0811 DEBUG Abnormal ELS completion VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that an ELS command completed with a status error in the IOCB It could mean the Fibre Channel device on the network is not responding or the Fibre Channel device is not an FCP target The driver will automatically SEVERITY LEVEL Debug MESSAGE Abnormal ELS completion ACTION retry this ELS command if needed If the command is a PLOGI or PRLI and the destination PortID is not an FCP Target no action is needed Otherwise check physical connections to Fibre Channel network and the state the remote PortID is in Emulex Drivers for Solaris User Manual Page 28 gt E EMULEX MSG_ID 0820 DEBUG ELS rcvd VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that an unsolicited ELS command was received SEVERITY LEVEL Debug MESSAGE ELS rcvd ACTION No action needed informational MSG_ID 0821 DEBUG Unsolicited ELS dropped VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that an unsolicited ELS command was received and then dropped for some reason SEVERITY LEVEL Debug MESSAGE Unsolicited ELS dropped ACTION No action needed informational MSG_ID 0822 DEBUG ELS reply VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that a reply is being sent for an unsolicited ELS command SEVERITY LEVEL Debug MESSAGE ELS reply ACTION No action needed informational M
4. num nodes 4096 Adapter reset The number of remote FC nodes NPorts the driver supports 0 no_limit else must be gt 2 pci max read 2048 512 4096 Adapter reset Sets the PCI X max memory read byte count 512 1024 2048 or 4096 pm support Reboot Enables or disables power management support in the driver 0 Disables power management support 1 Enables power management support target depth 512 2048 Link reset Sets remote FCP target queue depth 0 no_limit N Maximum active I Os Emulex Drivers for Solaris User Manual Page 9 gt G EMULEX Table 1 FC Configuration File Parameters Continued Property Name Default Min Max Activation Comments target mode Reboot Solaris 11 only Enables or disables COMSTAR target mode support If target mode is enabled for that port then the SFS initiator mode is disabled for that port topology 0 0 loop then PTP 2 PTP only 4 loop only 6 PTP then loop Link reset Set to point to point mode if you want to run as an N_Port Set to loop mode if you want to run as an NL_Port ub bufs vport 16320 Sets the number of unsolicited buffers the driver should allocate 1000 40 Reboot Solaris 10 only Virtual port registration table The enable npiv must be set to 1 The vport table may have any number of comma delimited entries Eac
5. MSG_ID 1411 DEBUG DFC detail VERBOSE_MASK LOG_IOCTL_DETAIL 0x04000000 DESCRIPTION This provides detailed information about the driver s DFC interface SEVERITY LEVEL Debug MESSAGE DFC detail ACTION No action needed informational MSG_ID 1420 DEBUG DFC Error VERBOSE_MASK LOG_IOCTL 0x00004000 DESCRIPTION This indicates that an error was found while processing a DFC request SEVERITY LEVEL Debug MESSAGE DFC Error ACTION No action needed informational Firmware Download Events MSG_ID 1500 DEBUG Firmware image VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This provides general information about the firmware image SEVERITY LEVEL Debug MESSAGE Firmware image ACTION No action needed informational MSG_ID 1501 DEBUG Firmware detail VERBOSE_MASK LOG_FIRMWARE_ DETAIL 0x10000000 DESCRIPTION This provides detailed information about the firmware image SEVERITY LEVEL Debug MESSAGE Firmware detail ACTION No action needed informational MSG_ID 1502 NOTICE Firmware Library VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This shows the versions of firmware contained in the driver s library SEVERITY LEVEL Notice MESSAGE Firmware Library ACTION No action needed informational MSG_ID 1510 ERROR Bad firmware image VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that a bad firmware image was provided to the download function SEVERITY LEVEL
6. SAN and accept logins from all ports NOTE In a SAN where there are other initiators this feature greatly reduces the driver s use of hardware resources Emulex Drivers for Solaris User Manual Page 11 gt G EMULEX Console and Log Messages Driver Logs General Situations If an FC link fails to come up verify that an 8 Gb s adapter is not attempting to connect to a 1 Gb s device Only 2 Gb s 4 Gb s and 8 Gb s devices are supported on 8 Gb s adapters Messages This section describes the type of console and log messages you may see Security levels and an extensive listing of message IDs and descriptions are also provided Log messages are logged to the var adm messages system file Table 2 lists the types of notices warnings and error logging levels you may set Table 2 Notice Warnings and Error Types driver errors to the console Driver Property Site Effect of Changing Default Related Ipfc Driver Property console notices 0 Sets the verbose level for log only when set to 0 log driver notices to the console messages are logged to the system log file and also printed console warnings 0 Sets the verbose level for on the console driver warnings to the console console errors 0 Sets the verbose level for Defaut Disablea log notices Oxffffffff Sets the verbose level for driver notices to the system log file log warnings Oxffffffff Sets the verbose level for
7. report this error to your customer service representative MSG_ID 1523 WARNING Firmware updated VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that new firmware has been updated on the adapter SEVERITY LEVEL Warning MESSAGE Firmware updated ACTION A reboot or adapter power cycle will be required to activate the new firmware MSG_ID 1530 DEBUG Firmware dump VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that a firmware core dump has occurred SEVERITY LEVEL Debug MESSAGE Firmware dump ACTION Check your hardware configuration If the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 37 gt G EMULEX MSG_ID 1540 WARNING Firmware update required VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that a firmware update is required on the adapter SEVERITY LEVEL Warning MESSAGE Firmware update required ACTION The user must perform a manual adapter reset or link reset once the host environment is stable to trigger an automatic firmware download Do not power cycle or reboot the system during the download operation Common Transport Events MSG_ID 1600 DEBUG CT sent VERBOSE_MASK LOG_CT 0x00010000 DESCRIPTION This indicates that a CT command is being sent SEVERITY LEVEL Debug MESSAGE CT sent ACTION No action needed informational MSG_ID 1601 DEBUG CT c
8. DESCRIPTION This indicates that an error was found while processing a DFC request SEVERITY LEVEL Debug MESSAGE FCSP error ACTION No action needed informational MSG_ID 1705 DEBUG FCSP state VERBOSE_MASK LOG_FCSP 0x00020000 DESCRIPTION This indicates that an authentication state is changing SEVERITY LEVEL Debug MESSAGE FCSP state ACTION No action needed informational MSG_ID 1706 DEBUG FCSP event VERBOSE_MASK LOG_FCSP 0x00020000 DESCRIPTION This indicates that an authentication event has occurred SEVERITY LEVEL Debug MESSAGE FCSP event ACTION No action needed informational MSG_ID 1707 DEBUG FCSP status VERBOSE_MASK LOG_FCSP 0x00020000 DESCRIPTION This indicates that an authentication status is being updated SEVERITY LEVEL Debug MESSAGE FCSP status ACTION No action needed informational MSG_ID 1710 DEBUG FCSP start VERBOSE_MASK LOG_FCSP 0x00020000 DESCRIPTION This indicates that authentication is being started to a specific node SEVERITY LEVEL Debug MESSAGE FCSP start ACTION No action needed informational MSG_ID 1720 DEBUG FCSP comp VERBOSE_MASK LOG_FCSP 0x00020000 DESCRIPTION This indicates that authentication is being stopped or completed to a specific node SEVERITY LEVEL Debug MESSAGE FCSP comp ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 40 gt EMULEX Fibre Channel Fabric FCF Events
9. Error MESSAGE Bad firmware image ACTION Obtain the proper image file If the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 36 gt E EMULEX MSG_ID 1511 ERROR Firmware image not compatible VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that the firmware image provided was not compatible with the existing hardware SEVERITY LEVEL Error MESSAGE Firmware image not compatible ACTION Obtain the proper image file If the problem persists report this error to your customer service representative MSG_ID 1520 NOTICE Firmware download VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that an attempt to download a firmware image has occurred SEVERITY LEVEL Notice MESSAGE Firmware download ACTION No action needed informational MSG_ID 1521 NOTICE Firmware download complete VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that an attempt to download a firmware image was successful SEVERITY LEVEL Notice MESSAGE Firmware download complete ACTION No action needed informational MSG_ID 1522 ERROR Firmware download failed VERBOSE_MASK LOG_FIRMWARE 0x00008000 DESCRIPTION This indicates that an attempt to download a firmware image was failed SEVERITY LEVEL Error MESSAGE Firmware download failed ACTION Check your hardware configuration If the problem persists
10. driver warnings to the system log file log errors Oxffffffff Sets the verbose level for driver errors to the system log file log verbose when set to non zero verbose messages are generated Default Disabled Table 3 lists the types of log messages that can be logged to the system file Table 3 Log Message Types LOG Message Verbose Verbose Bit Verbose Description Mask LOG_MISC 0x00000001 Miscellaneous events LOG_DRIVER 0x00000002 Driver attach and detach events Emulex Drivers for Solaris User Manual Page 12 Table 3 Log Message Types Continued gt G EMULEX LOG Message Verbose Verbose Description Mask Verbose Bit LOG_INIT 0x00000004 HBA Initialization events LOG_MEM 0x00000008 Memory management events LOG_SLI 0x00000010 Service Level Interface SLI events LOG_MBOX 0x00000020 Mailbox events LOG_NODE 0x00000040 Node events LOG_LINK 0x00000080 Link events LOG_ELS 0x00000100 ELS events LOG_PKT 0x00000200 General I O packet events LOG_FCP 0x00000400 FCP traffic events LOG_FCT 0x00000800 FCP target mode events LOG_IP 0x00001000 IP traffic events LOG_SFS 0x00002000 Solaris SFS events LOG_IOCTL 0x00004000 IOCTL events LOG_FIRMWARE 0x00008000 Firmware download events LOG_CT 0x00010000 CT events LOG_FCSP 0x00020000 FCSP events LOG_RESERVED 0x007C0000 Reserved for f
11. gt 56 EMULEX Emulex Drivers for Solaris FC version 2 75h User Manual Emulex Connects P007643 01A Rev A Servers Storage and People gt G EMULEX Copyright 2003 2011 Emulex All rights reserved worldwide No part of this document may be reproduced by any means or translated to any electronic medium without the prior written consent of Emulex Information furnished by Emulex is believed to be accurate and reliable However no responsibility is assumed by Emulex for its use or for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent copyright or related rights of Emulex Emulex the Emulex logo AutoPilot Installer AutoPilot Manager BlockGuard Connectivity Continuum Convergenomics Emulex Connect Emulex Secure EZPilot FibreSpy InSpeed LightPulse MultiPulse OneCommand OneConnect One Network One Company SBOD SLI and VEngine are trademarks of Emulex All other brand or product names referenced herein are trademarks or registered trademarks of their respective companies or organizations Emulex provides this manual as is without any warranty of any kind either expressed or implied including but not limited to the implied warranties of merchantability or fitness for a particular purpose Emulex may make improvements and changes to the product described in this manual at any time and without any notice Emulex a
12. more information refer to the OneCommand Manager Application User Manual e Using the Emulex FCA utilities emlxadm utility and emlxdrv utility For overviews on the emlxadm and emlxdrv utilities refer to page 2 For more information refer to the Solaris FCA Utilities User Manual If the Emulex LPFC driver for Solaris is already installed you can migrate to the SFS FCA driver either by customizing and running the unsupported sample scripts provided by Emulex or by manually performing a set of procedures Changing Driver Properties Using the Configuration File The configuration file contains all the properties necessary to initialize the Emulex SFS FCA driver The configurable driver properties are described in Table 1 on page 7 All adapter specific properties have an elxfcX prefix where X is the driver instance number For example setting emfcO link speed 4 makes 4 the default link speed setting for the zero instance of the driver Changes to the configuration file require you to unload and reload the driver To change driver properties 1 Open the configuration file in a text editor 2 Change the properties you want 3 Save the file Note Refer to Table 1 on page 7 for activation requirements Enabling NPIV Support on Solaris 10 To enable N_Port ID Virtualization NPIV support in the driver Login as or su to root Set enable npiv to 1 in the configuration file The fp driver properties are updated when t
13. not complete because of some issue SEVERITY LEVEL Warning MESSAGE Diagnostic error ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 1311 DEBUG ECHO diagnostic completed VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This indicates that an ECHO diagnostic has completed SEVERITY LEVEL Debug MESSAGE ECHO diagnostic completed ACTION No action needed informational MSG_ID 1312 WARNING ECHO diagnostic failed VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This indicates that an ECHO diagnostic has failed to return a positive result This could indicate a connectivity problem with your FC network SEVERITY LEVEL Warning MESSAGE ECHO diagnostic failed ACTION Check your network connections If the problem persists report this error to your system administrator MSG_ID 1313 DEBUG BIU diagnostic completed VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This indicates that a BIU diagnostic has completed SEVERITY LEVEL Debug MESSAGE BIU diagnostic completed ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 34 gt G EMULEX MSG_ID 1314 ERROR BIU diagnostic failed VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This indicates that a BIU diagnostic has failed to return a positive result This usually caused by an adapter hardware problem SEVERITY LEVEL Error MESSAGE
14. the error or event occurred sunv240 identifies the name of the host machine lt module name gt identifies that the message came from the Emulex inbox or out of box driver ID 349649 kern info identifies a Solaris specific message ID and kernel message level This will change from one driver message to another 5 0336 identifies the driver message context tag This may change from one driver version to another elxfcO identifies the message is coming from the elxfc driver instance zero This will change from one driver instance to another NOTICE identifies the driver message severity level This may change from one driver version to another 720 identifies the driver message id This will not change from one driver version to another Link up identifies the actual error or event message This will not change from one driver version to another 1 Gb s fabric identifies additional information specific to the error or event message This information is normally intended for technical support engineering use This may change from one driver version to another Emulex Drivers for Solaris User Manual Page 14 Miscellaneous Events MSG_ID 0001 DEBUG VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This is a general purpose informational message SEVERITY LEVEL Debug MESSAGE None ACTION No action needed informational MSG_ID 0002 NOTICE VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This is a general purp
15. 000040 DESCRIPTION This indicates that a node has been updated for a remote device SEVERITY LEVEL Debug MESSAGE Node updated ACTION No action needed informational MSG_ID 0610 DEBUG Node destroy VERBOSE_MASK LOG_NODE 0x00000040 DESCRIPTION This indicates that a node has been destroyed for a remote device SEVERITY LEVEL Debug MESSAGE Node destroy ACTION No action needed informational MSG_ID 0611 DEBUG Node closed VERBOSE_MASK LOG_NODE_DETAIL 0x02000000 DESCRIPTION This indicates that a node has been temporarily closed for I O transport SEVERITY LEVEL Debug MESSAGE Node closed ACTION No action needed informational MSG_ID 0612 NOTICE Node missing VERBOSE_MASK LOG_NODE 0x00000040 DESCRIPTION This indicates that a FCP2 device node has been found missing SEVERITY LEVEL Notice MESSAGE Node missing ACTION No action needed informational MSG_1ID 0620 DEBUG Node not found VERBOSE_MASK LOG_NODE 0x00000040 DESCRIPTION This indicates that there was an attempt to send an I O pkt to an unknown device node The driver maintains a node table entry for every device it needs to communicate with on the FC network SEVERITY LEVEL Debug MESSAGE Node not found ACTION No action needed informational However if the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 26 gt G EMULEX MSG_ID 0621 DEBUG N
16. BIU diagnostic failed ACTION Contact your customer service representative MSG_ID 1315 DEBUG POST diagnostic completed VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This indicates that a POST diagnostic has completed SEVERITY LEVEL Debug MESSAGE POST diagnostic completed ACTION No action needed informational MSG_ID 1316 ERROR POST diagnostic failed VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This indicates that a POST diagnostic has failed to return a positive result This is usually caused by an adapter hardware problem SEVERITY LEVEL Error MESSAGE POST diagnostic failed ACTION Contact your customer service representative IOCTL Events MSG_ID 1400 DEBUG IOCTL VERBOSE_MASK LOG_IOCTL 0x00004000 DESCRIPTION This provides general information about the driver s IOCTL interface SEVERITY LEVEL Debug MESSAGE IOCTL ACTION No action needed informational MSG_ID 1401 DEBUG IOCTL detail VERBOSE_MASK LOG_IOCTL_DETAIL 0x04000000 DESCRIPTION This provides detailed information about the driver s IOCTL interface SEVERITY LEVEL Debug MESSAGE IOCTL detail ACTION No action needed informational MSG_ID 1410 DEBUG DFC VERBOSE_MASK LOG_IOCTL 0x00004000 DESCRIPTION This provides general information about the driver s DFC interface SEVERITY LEVEL Debug MESSAGE DFC ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 35 gt G EMULEX
17. CRIPTION This indicates that an unsolicited CT command was received and then dropped for some reason SEVERITY LEVEL Debug MESSAGE Unsolicited CT dropped ACTION No action needed informational MSG_ID 1622 DEBUG CT reply VERBOSE_MASK LOG_CT 0x00010000 DESCRIPTION This indicates that a reply is being sent for an unsolicited CT command SEVERITY LEVEL Debug MESSAGE CT reply ACTION No action needed informational MSG_ID 1630 ERROR Invalid CT command found VERBOSE_MASK LOG_CT 0x00010000 DESCRIPTION This indicates that a CT command was found with an invalid command code SEVERITY LEVEL Error MESSAGE Invalid CT command found ACTION No action needed informational However if the problem persists report this error to your customer service representative Fibre Channel Security Protocol FCSP Events MSG_ID 1700 DEBUG FCSP VERBOSE_MASK LOG_FCSP 0x00020000 DESCRIPTION This provides general information about the driver s FCSP interface SEVERITY LEVEL Debug MESSAGE FCSP ACTION No action needed informational MSG_ID 1701 DEBUG FCSP detail VERBOSE_MASK LOG_FCSP_DETAIL 0x01000000 DESCRIPTION This provides detailed information about the driver s FCSP interface SEVERITY LEVEL Debug MESSAGE FCSP detail ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 39 gt E EMULEX MSG_ID 1702 DEBUG FCSP error VERBOSE_MASK LOG_FCSP 0x00020000
18. ICE Adapter Async Status VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter has provided general information about the adapter s async status SEVERITY LEVEL Notice MESSAGE Adapter Async Status ACTION No action needed informational MSG_ID 0430 DEBUG Ring event VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an SLI ring event has occurred SEVERITY LEVEL Debug MESSAGE Ring event ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 22 gt G EMULEX MSG_ID 0431 DEBUG Ring error VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an SLI ring error is being reported by the adapter SEVERITY LEVEL Debug MESSAGE Ring error ACTION No action needed informational MSG_ID 0432 DEBUG Ring reset VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an SLI ring is being reset SEVERITY LEVEL Debug MESSAGE Ring reset ACTION No action needed informational MSG_ID 0440 DEBUG Adapter msg VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that a message was sent to the driver from the adapter SEVERITY LEVEL Debug MESSAGE Adapter msg ACTION No action needed informational MSG_ID 0450 ERROR IOCB invalid VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an IOCB was received from the adapter with an illegal value This error could indicate a
19. ITY LEVEL Debug MESSAGE Link atten ACTION No action needed informational MSG_ID 0411 DEBUG State change VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter has changed state SEVERITY LEVEL Debug MESSAGE State change ACTION No action needed informational MSG_ID 0412 DEBUG Link Up atten VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter has triggered a link up attention interrupt SEVERITY LEVEL Debug MESSAGE Link Up atten ACTION No action needed informational MSG_ID 0413 DEBUG Link Down atten VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter has triggered a link down attention interrupt SEVERITY LEVEL Debug MESSAGE Link Down atten ACTION No action needed informational MSG_ID 0420 ERROR Adapter hardware error VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an interrupt has occurred and the status register indicates a nonrecoverable hardware error SEVERITY LEVEL Error MESSAGE Adapter hardware error ACTION This error usually indicates a hardware problem with the adapter Try running adapter diagnostics Report these errors to customer service MSG_ID 0421 NOTICE Adapter temperature VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter has provided general information about the adapter s temperature SEVERITY LEVEL Notice MESSAGE Ad
20. MESSAGE Adapter online ACTION No action needed informational MSG_ID 0230 DEBUG Adapter offline VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that the adapter is offline and unable to communicate SEVERITY LEVEL Debug MESSAGE Adapter offline ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 18 gt G EMULEX MSG_ID 0231 WARNING Adapter shutdown VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that the adapter has been shutdown and will require a reboot to reinitialize SEVERITY LEVEL Warning MESSAGE Adapter shutdown ACTION Contact your customer service representative MSG_ID 0240 ERROR Adapter reset failed VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that an attempt to reset the adapter has failed SEVERITY LEVEL Error MESSAGE Adapter reset failed ACTION Check your hardware configuration If the problem persists report this error to your customer service representative Memory Management Events MSG_ID 0300 DEBUG Memory alloc VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This indicates that the driver allocated system memory SEVERITY LEVEL Debug MESSAGE Memory alloc ACTION No action needed informational MSG_ID 0301 ERROR Memory alloc failed VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This indicates that the driver was unable to allocate system memory The system is low on memory
21. MSG_ID 1800 DEBUG FCF VERBOSE_MASK DESCRIPTION This provides general information about the driver s FCF interface SEVERITY LEVEL Debug MESSAGE FCF ACTION No action needed informational MSG_ID 1801 DEBUG FCF detail VERBOSE_MASK DESCRIPTION This provides detailed information about the driver s FCF interface SEVERITY LEVEL Debug MESSAGE FCF detail ACTION No action needed informational MSG_ID 1810 DEBUG FCF error VERBOSE_MASK DESCRIPTION This indicates that an error was found while processing an FCF request SEVERITY LEVEL Debug MESSAGE FCF error ACTION No action needed informational MSG_ID 1820 DEBUG FCF state VERBOSE_MASK DESCRIPTION This indicates that an FCF object state is changing SEVERITY LEVEL Debug MESSAGE FCF state ACTION No action needed informational MSG_ID 1830 DEBUG FCF event VERBOSE_MASK DESCRIPTION This indicates that an FCF event has occurred SEVERITY LEVEL Debug MESSAGE FCF event ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 41
22. RBOSE_MASK DESCRIPTION This provides an API trace with the driver s FCT interface SEVERITY LEVEL Debug MESSAGE FCT API ACTION No action needed informational IP Traffic Events MSG_ID 1200 DEBUG IP detail VERBOSE_MASK LOG_IP_DETAIL 0x08000000 DESCRIPTION This provides detailed information about the driver s IP interface SEVERITY LEVEL Debug MESSAGE IP detail ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 32 gt E EMULEX MSG_ID 1210 ERROR Stray IP completion VERBOSE_MASK LOG_IP 0x00001000 DESCRIPTION This indicates that an IP sequence completion was received without issuing a corresponding IP sequence This error could indicate a driver or firmware problem SEVERITY LEVEL Error MESSAGE Stray IP completion ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 1211 DEBUG Abnormal IP completion VERBOSE_MASK LOG_IP 0x00001000 DESCRIPTION This indicates that an IP sequence completed with a status error in the IOCB It could mean the Fibre Channel device on the network is not responding SEVERITY LEVEL Debug MESSAGE Abnormal IP completion ACTION No action needed informational However if the problem persists report this error to your system administrator MSG_ID 1220 DEBUG Unsolicited IP dropped VERBOSE_MASK LOG_IP 0x00001000 DESCRIPTION This ind
23. SG_1ID 0830 ERROR Invalid ELS command found VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that an ELS command was found with an invalid command code SEVERITY LEVEL Error MESSAGE Invalid ELS command found ACTION No action needed informational However if the problem persists report this error to your customer service representative General I O Packet Events MSG_ID 0900 NOTICE Packet abort VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an I O packet is being aborted SEVERITY LEVEL Notice MESSAGE Packet abort ACTION No action needed informational MSG_ID 0901 WARNING Packet abort failed VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an attempt to abort an I O packet has failed SEVERITY LEVEL Warning MESSAGE Packet abort failed ACTION No action needed informational However if the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 29 gt E EMULEX MSG_ID 0910 DEBUG Packet timeout VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an I O packet has timed out and is being aborted SEVERITY LEVEL Debug MESSAGE Packet timeout ACTION No action needed informational MSG_ID 0911 DEBUG CHANNEL watchdog VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that I O s are getting stale waiting on a I O channel tx queue SEVERIT
24. Y LEVEL Debug MESSAGE CHANNEL watchdog ACTION No action needed informational MSG_ID 0912 DEBUG TXQ watchdog VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an I O was found missing from the transmit queue SEVERITY LEVEL Debug MESSAGE TXQ watchdog ACTION No action needed informational MSG_ID 0920 DEBUG Packet flush VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an I O packet is being flushed SEVERITY LEVEL Debug MESSAGE Packet flush ACTION No action needed informational MSG_ID 0921 DEBUG Packet flushed VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an I O packet has been flushed SEVERITY LEVEL Debug MESSAGE Packet flushed ACTION No action needed informational MSG_ID 0922 NOTICE Packet flush timeout VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an I O packet flush request has timed out with some I O packets s still not completed The driver will attempt to recover by itself SEVERITY LEVEL Notice MESSAGE Packet flush timeout ACTION No action needed informational However if the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 30 gt E EMULEX MSG_ID 0930 NOTICE Packet transport failed VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an attempt to send an I O packet failed The I O packet
25. aaeeeeeeeesaaaaeeeeeeeeseeeeenaas 15 Driver EVENS susssissrcnsnaaaathaathanatnansnencnandeatonanan eandnandhoneaduaeananeesnonaaanendednanane 16 HBA Initialization Events cccccccecceeeeeeeeeeeeeeaeeeeeeeeeeeeeeeaaaaeeeeeeeeeeeeesaaas 18 Memory Management Events isiissiissstnastnesssansnestsastnedenentoaseoastonsenastinnenenanese 19 Service Level Interface SLI Events ccceecceeeeeeeecneeeeeeeeteteetceeeeeees 20 MalIDOxX EVE MISS aiaa E A E E 24 Node Event C EAEE 25 EINK EVENTS aoaaa AEA a E E E EA AE 27 ESE A 6 28 General I O Packet Events seesseseseeeeessesserrrrtsserrennnttsserrnennnennsestnenn 29 FCP Traffic Events cccccccccccccccceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess 31 FOT Traffic Events ss ccccseeacucecevaceccshaacuecsuasescacenacuactuaacuecsuaacueceucaceactsauasacaeaeas 32 IP Traffic Events cccccececeeeeeeeeeeeeeeeeeaeeeeeeeeeeeeeaaaeeaeeeeeeeeesaaaaneeeeeeeeesaaa 32 Solaris SFS EVENS ssssissssecssssssaccecesdinceensdancqnnsddannansddannansddannanahdenaaadaaaaadaned 34 IOCTL EV nts cccccccccccceeccceeeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeness 35 Firmware Download Events cccccccceeeeeeeeeeeeeecaeeeeeeeeeeeeeeeaaaeeeeeeeeeeeeaas 36 Common Transport Events cccccceeseeeeeeeceeeeeeeeeeeeecaaeeeeeeeeeseeesnaeeeeeers 38 Emulex Drivers for Solaris User Manual Page iii Fibre Channel Security Protocol FCSP Events
26. apter temperature ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 21 gt E EMULEX MSG_ID 0422 WARNING Adapter temperature VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter s temperature is too hot SEVERITY LEVEL Warning MESSAGE Adapter temperature ACTION Check hardware ventilation Reduce adapter usage Shutdown host system MSG_ID 0423 NOTICE Adapter notice VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter has provided general information about the adapter s condition SEVERITY LEVEL Notice MESSAGE Adapter notice ACTION No action needed informational MSG_ID 0424 WARNING Adapter warning VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an interrupt has occurred indicating a recoverable adapter error SEVERITY LEVEL Warning MESSAGE Adapter warning ACTION This error usually indicates a hardware or firmware problem with the adapter Check and or update firmware levels Report these errors to customer service MSG_ID 0425 ERROR Adapter error VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that a recoverable adapter error has occurred SEVERITY LEVEL Error MESSAGE Adapter error ACTION This error usually indicates a hardware or firmware problem with the adapter Check and or update firmware levels Report these errors to customer service MSG_ID 0426 NOT
27. ction needed informational MSG_ID 0462 DEBUG SLI DEBUG VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This provides debug information about an SLI event SEVERITY LEVEL Debug MESSAGE SLI DEBUG ACTION No action needed informational Mailbox Events MSG_ID 0500 DEBUG Mailbox event VERBOSE_MASK LOG_MBOX 0x00000020 DESCRIPTION This indicates that a mailbox event has occurred SEVERITY LEVEL Debug MESSAGE Mailbox event ACTION No action needed informational MSG_ID 0501 DEBUG Mailbox detail VERBOSE_MASK LOG_MBOX_DETAIL 0x40000000 DESCRIPTION This provides detailed information about a mailbox event SEVERITY LEVEL Debug MESSAGE Mailbox detail ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 24 gt E EMULEX MSG_ID 0510 DEBUG Stray mailbox interrupt VERBOSE_MASK LOG_MBOX 0x00000020 DESCRIPTION This indicates that a mailbox command completion interrupt was received and the mailbox is not valid This error could indicate a driver or firmware problem SEVERITY LEVEL Debug MESSAGE Stray mailbox interrupt ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 0520 DEBUG Mailbox error VERBOSE_MASK LOG_MBOX 0x00000020 DESCRIPTION This indicates that an unsupported or illegal mailbox command was completed This error could indicate a driver or firmware
28. driver or firmware problem SEVERITY LEVEL Error MESSAGE IOCB invalid ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 0451 DEBUG IOCB queue full VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the IOCB queue is full This will occur during normal operation SEVERITY LEVEL Debug MESSAGE IOCB queue full ACTION No action needed informational MSG_ID 0452 DEBUG IOCB event VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an IOCB local error event is being reported by the adapter SEVERITY LEVEL Debug MESSAGE IOCB event ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 23 gt G EMULEX MSG_ID 0453 DEBUG IOCB stale VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that an IOCB completed after its associated packet completed SEVERITY LEVEL Debug MESSAGE IOCB stale ACTION No action needed informational MSG_ID 0460 DEBUG SLI detail VERBOSE_MASK LOG_SLI_DETAIL 0x80000000 DESCRIPTION This provides detailed information about an SLI event SEVERITY LEVEL Debug MESSAGE SLI detail ACTION No action needed informational MSG_ID 0461 ERROR SLI ERROR VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This error provides information about an SLI event SEVERITY LEVEL Error MESSAGE SLI ERROR ACTION No a
29. eeeeccnaeeeeeeeeeseeccaeeeeeeeeseeeecceeeeeees 4 alt cele Ue 6 9 Wenectrererer ere eerrnerenere a ere errr cre a E E 4 Changing Driver Properties Using the Configuration File eecseeeeeeeeeeeeeees 4 Enabling NPIV Support on Solaris 10 c cccceecceeeeeeeeeeeeeeeeeeenceeeeeeeeeeeeesaaaes 4 Enabling NPIV Support on Solaris 11 cccccceeeeeeeeecneeeeeeeeeeeeeenceeeeeeeeeeeeeaaees 5 NPIV Configuration Limits 0 cccceeeccceceeeeeee eter ee eeeecaaeeeeeeeeeeeeecaeeeeeeeeeetees 5 NPIV and OS Virtualization seccu 5 Using VPorts with Oracle VM Server for SPARC Containers and Oracle VM Server for X86 0 0 nennen nnn nnn nnnnnnnnnnnnnnnnnnnnn ennenen 5 Configuring Target Mode Support for Solaris 11 eeseseeeeeeeeeee eeen 6 Emulex SFS FCA Driver Properties c cccceeeeeeeeeceeeeeeeeeeeeeecneeeeeeeeeeeeenaaaes 6 The Configuration File eeeeeseeseneeeeeeerneessesrerrrrrrnrtsssrrrnnrnnnsserrrenssernnnnn 6 Console and Log MeSSagQes ccccceeeeeeeeeecneeeeeeeeeeeecaaeeeeeeeeeeeeecaaaeeeeeeeeeeecenaeeeeeees 12 Dior ele EERE E E E E E E E E EE 12 General SIU ANONS sseni iaa aa aa aaia 12 MESSA S C T EE eenes 12 Severity LeVEIS ccccccccceeeeeeeeccneeeeeeeeeeeeeeaeeeeeeeeeeeececaaeeeeeeeeeseescnaeeeeeees 14 Message Log Example nscisssssssssnsessstansseestanuanentanseaautannsaadsansnandeansedeutpeceecede 14 Miscellaneous Events cccceeeecceeeeeeceeeeeeeeeeeeca
30. er reset Sets the driver wait period seconds for a link up after adapter initialization log errors OxFFFFFFFF 0x00000000 OxFFFFFFFF Dynamic Verbose mask for error messages to the messages file log notices OxFFFFFFFF 0x00000000 OxFFFFFFFF Dynamic Verbose mask for notice messages to the messages file log warnings OxFFFFFFFF 0x00000000 OxFFFFFFFF Dynamic Verbose mask for warning messages to the messages file Emulex Drivers for Solaris User Manual Page 8 Table 1 FC Configuration File Parameters Continued gt G EMULEX Property Name Default Min Max Activation Comments max xfer size 339968 131072 1388544 Reboot Sets the maximum SCSI transfer size in bytes per I O This property is only used by the driver on i386 platforms The driver does not limit transfer size on SPARC platforms This property determines the scatter gather list buffer size A pool of buffers is reallocated by the driver during boot A larger transfer size requires a larger memory allocation Memory_model max xfer size Small 131072 339968 Medium 339969 688128 Large 688129 1388544 network on Reboot Enables disables IP networking support in the driver O Disabled 1 Enabled num iocbs 1024 128 10240 Adapter reset The number of Input Output Control Block IOCB buffers to allocate
31. er or firmware problem SEVERITY LEVEL Debug MESSAGE Stray FCP completion ACTION No action needed informational However if the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 31 gt G EMULEX MSG_ID 1001 DEBUG FCP completion error VERBOSE_MASK LOG_FCP 0x00000400 DESCRIPTION This indicates that an FCP command completed with an error status These errors can occur during normal operation SEVERITY LEVEL Debug MESSAGE FCP completion error ACTION No action needed informational FCT Traffic Events MSG_ID 1100 DEBUG FCT detail VERBOSE_MASK LOG_FCT_DETAIL 0x00800000 DESCRIPTION This provides detailed information about the driver s FCT interface SEVERITY LEVEL Debug MESSAGE FCT detail ACTION No action needed informational MSG_ID 1110 DEBUG FCT debug VERBOSE_MASK LOG_FCT 0x00000800 DESCRIPTION This provides general information about the driver s FCT interface SEVERITY LEVEL Debug MESSAGE FCT debug ACTION No action needed informational MSG_ID 1120 DEBUG FCT error VERBOSE_MASK LOG_FCT 0x00000800 DESCRIPTION This indicates that a general error has occurred in the driver s FCT interface SEVERITY LEVEL Debug MESSAGE FCT error ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 1130 DEBUG FCT API VE
32. es to the console console notices 0x00000000 0x00000000 OxFFFFFFFF Dynamic Verbose mask for notice messages to the console console warnings 0x00000000 0x00000000 OxFFFFFFFF Dynamic Verbose mask for warning messages to the console cr count 255 Link reset Specifies a count of I O completions after which an interrupt response is generated This property is disabled if cr delay is set to 0 Emulex Drivers for Solaris User Manual Page 7 Table 1 FC Configuration File Parameters Continued gt G EMULEX Property Name Default Min Max Activation Comments cr delay 63 Link reset Specifies a count of milliseconds after which an interrupt response generated if cr count has not been satisfied This property is set to 0 to disable the Coalesce Response feature as default enable auth Link reset Enables DHCHAP support in the driver 0 Disabled 1 Enabled enable npiv Adapter reset Enables NPIV support in the driver 0 Disabled remove all vports first 1 Enabled requires SLI3 fct queue depth 4096 Reboot Queue depth of target mode port 0 max determined by type of HBA link speed 0 Auto Detect 0 Auto Detect 2 2 Gb s 4 4 Gb s 8 8 Gb s 16 16 Gb s Link reset Sets the link speed for initializing FC connection linkup delay 10 0 60 Adapt
33. exhausted The I O will be dropped and most likely retried by the remote device SEVERITY LEVEL Notice MESSAGE No unsolicited buffer available ACTION If the problem occurs frequently you may be able to configure more resources for that pool If this does not solve the problem report these errors to customer service MSG_ID 0330 ERROR Invalid access handle VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This indicates that the driver had an invalid access handle assigned by the system SEVERITY LEVEL Error MESSAGE Invalid access handle ACTION If the problem occurs frequently report these errors to customer service MSG_ID 0331 ERROR Invalid DMA handle VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This indicates that the driver had an invalid dma handle assigned by the system SEVERITY LEVEL Error MESSAGE Invalid DMA handle ACTION If the problem occurs frequently report these errors to customer service Service Level Interface SLI Events MSG_ID 0400 DEBUG Vital Product Data VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This provides vendor specific information about the adapter SEVERITY LEVEL Debug MESSAGE Vital Product Data ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 20 gt E EMULEX MSG_ID 0410 DEBUG Link atten VERBOSE_MASK LOG_SLI 0x00000010 DESCRIPTION This indicates that the adapter has triggered a link attention interrupt SEVER
34. ges the FCA drivers for each FC adapter attached to the host system Emulex Drivers for Solaris User Manual Page 2 gt G EMULEX The emlxadm Utility The emlxadm utility is used to change driver parameters through a local interactive or command line interface It can also be used for firmware updates on non Oracle branded devices Refer to the Solaris FCA Utilities User Manual for more information The emIxdrv Utility The emlxdrv utility associates the Emulex Solaris SFS out of box drivers and the Solaris LPFC driver to the various models of Emulex Fibre Channel adapters The emlxdrv utility is used for binding associating the Emulex Leadville Fibre Channel out of box drivers and the Emulex LPFC traditional non Leadville Fibre Channel driver to the various models of Emulex FC adapters If the driver binding configuration is changed the host system must usually be rebooted for the new configuration to take effect Refer to the Solaris FCA Utilities User Manual for more information Emulex Drivers for Solaris User Manual Page 3 gt G EMULEX FC Configuration and Migration Introduction elxfc is the module name for the Emulex SFS FCA out of box driver You can configure the Emulex SFS FCA driver properties by e Editing the configuration file emlxs conf or elxfc conf which is described in this section e Using the OneCommand Manager application For an overview on the OneCommand Manager application refer to page 2 For
35. guration If the problem persists report this error to your customer service representative MSG_ID 0112 DEBUG Driver detach VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver is performing a detach operation SEVERITY LEVEL Debug MESSAGE Driver detach ACTION No action needed informational MSG_ID 0120 DEBUG Driver suspend VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver is performing a suspend operation SEVERITY LEVEL Debug MESSAGE Driver suspend ACTION No action needed informational MSG_ID 0121 ERROR Driver suspend failed VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver was unable to suspend due to some issue SEVERITY LEVEL Error MESSAGE Driver suspend failed ACTION Check your hardware and software configuration If the problem persists report this error to your customer service representative MSG_ID 0130 DEBUG Driver resume VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver is performing a resume operation SEVERITY LEVEL Debug MESSAGE Driver resume ACTION No action needed informational MSG_ID 0131 ERROR Driver resume failed VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver was unable to resume due to some issue SEVERITY LEVEL Error MESSAGE Driver resume failed ACTION Check your hardware and software co
36. h entry must be of the form PHYS WWPN VPORT_WWNN VPORT_WWPN VPORT_ID PHYS_WWPN World Wide Port Name of adapter s physical port VPORT_WWNN Desired World Wide Node Name of virtual port VPORT_WWPN Desired World Wide Port Name of virtual port VPORT_ID Desired virtual port ID 1 to max vports The port IDs must start at 1 and increment by 1 with no gaps in the count The virtual port ID 0 is reserved for the physical port For example vport 10000000c9123456 28010000cC9123456 20010000cC9123456 1 10000000cC9123456 28020000C9123456 20020000C9123456 2 10000000cC9123457 28010000C9123457 20010000C9123457 1 10000000C9123457 28020000C9123457 20020000C9123457 2 10000000C9123457 28030000C9123457 20030000C9123457 3 All entries are automatically created or removed by the OneCommand Manager application Emulex Drivers for Solaris User Manual Page 10 Table 1 FC Configuration File Parameters Continued gt G EMULEX Property Name Default Min Max Activation Comments vport restrict login Link reset Sets the virtual port s behavior when discovering targets in the SAN 1 prevents the VPort from logging into other initiator ports on the SAN Also rejects logins from other ports in the SAN because it assumes that all ports that send a PLOGI are initiators When this parameter is turned off 0 the driver attempts to login to every port that it can access in the
37. he EMLXemlxu is installed Entries from 2 to 255 are added to the kernel drv fp conf file For example name fp class fibre channel port 0 name fp class fibre channel port 1 name fp class fibre channel port 2 name fp class fibre channel port 3 name fp class fibre channel port 4 name fp class fibre channel port 5 Emulex Drivers for Solaris User Manual Page 4 gt G EMULEX name fp class fibre channel port 6 name fp class fibre channel port 7 name fp class fibre channel port 8 name fp class fibre channel port 9 The first two lines are by default The above example adds ports 2 to 9 to support up to 10 virtual ports The port number of each entry must be in order with no gaps in between 4 Reboot the system To create delete and list virtual ports after a system reboot refer to the OneCommand Manager Application User Manual Enabling NPIV Support on Solaris 11 To enable NPIV support in the driver 1 Login as or su to root 2 Set enable npiv to 1 in the configuration file This is set to 0 by default 3 Reboot the system If enable npiv is already set do not reboot 4 Refer to Chapter 6 of the Solaris Express SAN Configuration and Multipathing Guide NPIV Configuration Limits The following limitations apply to NPIV e There is no Fibre Channel over IP FC IP support on virtual ports e You cannot delete a virt
38. icates that an unsolicited IP sequence was received but was dropped for some reason SEVERITY LEVEL Debug MESSAGE Unsolicited IP dropped ACTION No action needed informational MSG_ID 1221 DEBUG IP recvd VERBOSE_MASK LOG_IP 0x00001000 DESCRIPTION This indicates that an unsolicited IP sequence was received SEVERITY LEVEL Debug MESSAGE IP recvd ACTION No action needed informational MSG_ID 1230 ERROR Invalid IP sequence found VERBOSE_MASK LOG_IP 0x00001000 DESCRIPTION This indicates that an IP sequence was found with an invalid code SEVERITY LEVEL Error MESSAGE Invalid IP sequence found ACTION No action needed informational However if the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 33 gt G EMULEX Solaris SFS Events MSG_ID 1300 DEBUG SFS VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This provides general information about the driver s SFS interface SEVERITY LEVEL Debug MESSAGE SFS ACTION No action needed informational MSG_ID 1301 DEBUG SFS detail VERBOSE_MASK LOG_SFS_DETAIL 0x20000000 DESCRIPTION This provides detailed information about the driver s SFS interface SEVERITY LEVEL Debug MESSAGE SFS detail ACTION No action needed informational MSG_ID 1310 WARNING Diagnostic error VERBOSE_MASK LOG_SFS 0x00002000 DESCRIPTION This indicates that a diagnostic request did
39. lable on FC HBAs To configure target mode support for Solaris 11 Login as or su to root 2 Set target mode to 1 in the configuration file You can also set individual paths to target mode elxfcxX target mode 1 Where X is the specific numeric path For example when elxfc1 is set to target mode all other paths will stay in initiator mode 3 Uncomment the line ddi forceattach 1 4 Reboot the system To configure targets refer to the Oracle COMSTAR Administration document Emulex SFS FCA Driver Properties e The configuration file contains all the properties necessary to initialize the Emulex SFS FCA driver e The OneCommand Manager application reflects the configuration file driver properties Refer to the OneCommand Manager Application User Manual for more information about using the OneCommand Manager application with the Emulex SFS FCA driver e All properties are adapter specific Note If you are migrating from the LPFC driver to the out of box driver and if any of the default property values were changed verify that this change will not impact the migration before you proceed The Configuration File In the configuration file all adapter specific parameters have an elxfcX prefix where X is the driver instance number for example setting elxfcO link speed 4 makes 4 Gb s the default link speed For any changes to the configuration file to take effect you must unload and reload the driver
40. mational Driver Events MSG_ID 0100 NOTICE Driver attach VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver is performing an attach operation SEVERITY LEVEL Notice MESSAGE Driver attach ACTION No action needed informational MSG_ID 0101 ERROR Driver attach failed VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver was unable to attach due to some issue SEVERITY LEVEL Error MESSAGE Driver attach failed ACTION Check your hardware and software configuration If the problem persists report this error to your customer service representative MSG_ID 0102 DEBUG Driver attach VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver is performing a attach operation SEVERITY LEVEL Debug MESSAGE Driver attach ACTION No action needed informational MSG_ID 0110 NOTICE Driver detach VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver is performing a detach operation SEVERITY LEVEL Notice MESSAGE Driver detach ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 16 gt G EMULEX MSG_ID 0111 ERROR Driver detach failed VERBOSE_MASK LOG_DRIVER 0x00000002 DESCRIPTION This indicates that the driver was unable to detach due to some issue SEVERITY LEVEL Error MESSAGE Driver detach failed ACTION Check your hardware and software confi
41. nfiguration If the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 17 gt G EMULEX HBA Initialization Events MSG_ID 0200 NOTICE Adapter initialization VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that the adapter is initializing SEVERITY LEVEL Notice MESSAGE Adapter initialization ACTION No action needed informational MSG_ID 0201 ERROR Adapter initialization failed VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that an attempt to initialize the adapter has failed SEVERITY LEVEL Error MESSAGE Adapter initialization failed ACTION Check your hardware configuration If the problem persists report this error to your customer service representative MSG_ID 0202 DEBUG Adapter initialization VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that the adapter is initializing SEVERITY LEVEL Debug MESSAGE Adapter initialization ACTION No action needed informational MSG_ID 0210 DEBUG Adapter transition VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that the adapter is changing states SEVERITY LEVEL Debug MESSAGE Adapter transition ACTION No action needed informational MSG_ID 0220 DEBUG Adapter online VERBOSE_MASK LOG_INIT 0x00000004 DESCRIPTION This indicates that the adapter is online and ready to communicate SEVERITY LEVEL Debug
42. ode timeout VERBOSE_MASK LOG_NODE 0x00000040 DESCRIPTION This indicates that the node timer expired the node is ready to be opened or it has been offline too long and needs to be flushed SEVERITY LEVEL Debug MESSAGE Node timeout ACTION No action needed informational Link Events MSG_ID 0700 DEBUG Link event VERBOSE_MASK LOG_SLI 0x00000010 or LOG_LINK 0x00000080 DESCRIPTION This indicates that a link event has occurred SEVERITY LEVEL Debug MESSAGE Link event ACTION No action needed informational MSG_ID 0710 NOTICE Link down VERBOSE_MASK LOG_LINK 0x00000080 DESCRIPTION This indicates that the Fibre Channel link is down to the adapter SEVERITY LEVEL Notice MESSAGE Link down ACTION Check your network connections If the problem persists report this error to your system administrator MSG_ID 0720 NOTICE Link up VERBOSE_MASK LOG_LINK 0x00000080 DESCRIPTION This indicates that the Fibre Channel link is up SEVERITY LEVEL Notice MESSAGE Link up ACTION No action needed informational MSG_ID 0721 NOTICE NPIV Link up VERBOSE_MASK LOG_LINK 0x00000080 DESCRIPTION This indicates that the Fibre Channel link is up for all virtual ports SEVERITY LEVEL Notice MESSAGE NPIV Link up ACTION No action needed informational MSG_1ID 0730 NOTICE Link reset VERBOSE_MASK LOG_LINK 0x00000080 or LOG_SFS 0x00002000 DESCRIPTION This indicates that an issue ha
43. omp VERBOSE_MASK LOG_CT 0x00010000 DESCRIPTION This indicates that a CT command completed normally SEVERITY LEVEL Debug MESSAGE CT comp ACTION No action needed informational MSG_ID 1610 ERROR Stray CT completion VERBOSE_MASK LOG_CT 0x00010000 DESCRIPTION This indicates that a CT command completion was received without issuing a corresponding CT command This error could indicate a driver or firmware problem SEVERITY LEVEL Error MESSAGE Stray CT completion ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 1611 DEBUG Abnormal CT completion VERBOSE_MASK LOG_CT 0x00010000 DESCRIPTION This indicates that a CT command completed with a status error in the IOCB It could mean the Fibre Channel device on the network is not responding The driver will automatically retry this CT command if needed SEVERITY LEVEL Debug MESSAGE Abnormal CT completion ACTION Check physical connections to Fibre Channel network and the state the remote PortID is in Emulex Drivers for Solaris User Manual Page 38 gt G EMULEX MSG_ID 1620 DEBUG CT revd VERBOSE_MASK LOG_CT 0x00010000 DESCRIPTION This indicates that an unsolicited CT command was received SEVERITY LEVEL Debug MESSAGE CT revd ACTION No action needed informational MSG_ID 1621 DEBUG Unsolicited CT dropped VERBOSE_MASK LOG_CT 0x00010000 DES
44. ose informational message SEVERITY LEVEL Notice MESSAGE None ACTION No action needed informational MSG_ID 0003 WARNING VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This is a general purpose warning message SEVERITY LEVEL Warning MESSAGE None ACTION No action needed informational MSG_ID 0004 ERROR VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This is a general purpose error message SEVERITY LEVEL Error MESSAGE None ACTION No action needed informational MSG_ID 0005 PANIC VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This is a general purpose panic message SEVERITY LEVEL Panic Severe MESSAGE None ACTION Contact your customer service representative MSG_ID 0010 DEBUG Event VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This is debug information about a driver event SEVERITY LEVEL Debug MESSAGE Event ACTION No action needed informational Emulex Drivers for Solaris User Manual gt G EMULEX Page 15 gt G EMULEX MSG_ID 0011 DEBUG Event queued VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This indicates that a driver event is being queued SEVERITY LEVEL Debug MESSAGE Event queued ACTION No action needed informational MSG_ID 0012 DEBUG Event dequeued VERBOSE_MASK LOG_MISC 0x00000001 DESCRIPTION This indicates that a driver event is being dequeued SEVERITY LEVEL Debug MESSAGE Event dequeued ACTION No action needed infor
45. problem SEVERITY LEVEL Debug MESSAGE Mailbox error ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 0530 ERROR Mailbox timeout VERBOSE_MASK LOG_MBOX 0x00000020 DESCRIPTION The firmware did not response a mailbox command This error could indicate a hardware or firmware problem SEVERITY LEVEL Error MESSAGE Mailbox timeout ACTION No action needed informational However if the problem persists report this error to your customer service representative Node Events MSG_ID 0600 DEBUG Node create VERBOSE_MASK LOG_NODE 0x00000040 DESCRIPTION This indicates that a node has been created for a remote device SEVERITY LEVEL Debug MESSAGE Node create ACTION No action needed informational MSG_ID 0601 DEBUG Node opened VERBOSE_MASK LOG_NODE_DETAIL 0x02000000 DESCRIPTION This indicates that a node has been opened for I O transport SEVERITY LEVEL Debug MESSAGE Node opened ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 25 gt E EMULEX MSG_ID 0602 NOTICE Node create failed VERBOSE_MASK LOG_NODE 0x00000040 DESCRIPTION This indicates that a node create request for a remote device has failed SEVERITY LEVEL Notice MESSAGE Node create failed ACTION No action needed informational MSG_ID 0603 DEBUG Node updated VERBOSE_MASK LOG_NODE 0x00
46. resources SEVERITY LEVEL Error MESSAGE Memory alloc failed ACTION No action needed informational However if the problem persists report this error to your system administrator MSG_ID 0310 ERROR Memory pool error VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This indicates that a problem has occurred with the memory buffer pool management SEVERITY LEVEL Error MESSAGE Memory pool error ACTION No action needed informational However if the problem persists report this error to your customer service representative Emulex Drivers for Solaris User Manual Page 19 gt G EMULEX MSG_ID 0311 DEBUG Memory pool alloc failed VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This indicates that the driver was unable to allocate memory from one of its own memory pools SEVERITY LEVEL Debug MESSAGE Memory pool alloc failed ACTION If the problem occurs frequently you may be able to configure more resources for that pool If this does not solve the problem report these errors to customer service MSG_ID 0312 DEBUG Memory pool detail VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This provides detailed information about memory bufferpool management SEVERITY LEVEL Debug MESSAGE Memory pool detail ACTION No action needed informational MSG_ID 0320 NOTICE No unsolicited buffer available VERBOSE_MASK LOG_MEM 0x00000008 DESCRIPTION This indicates that the driver s unsolicited buffer pool is
47. root 2 Download the platform specific FC out of box driver from the Emulex website to a convenient directory The file is a regular tar file 3 Extract the installation image from the tar file For example cd lt location of driver package gt tar xvf elxfc_kit 2 66d s10 sparc tar 4 Install the driver kit For example cd lt location of driver package gt pkgadd d 5 Reboot the system Uninstalling the Drivers To uninstall the out of box driver Login as root 2 Remove the out of box driver by typing pkgrm lt OOB_pkg_name gt For example pkgrm EMLXelxfc 3 Reboot the system Utilities Emulex provides three utilities to facilitate configuring and using the Solaris drivers The OneCommand Manager application The emlxadm utility included in the FCA utility e The emlxdrv utility included in the FCA utility Note When you install the OneCommand Manager application also install the Solaris FCA Utilities The OneCommand Manager Application The OneCommand Manager application provides all the functions of emlxadm and a number of additional ones allowing you to remotely manage multiple systems It offers a choice of a graphical user interface and a scriptable command line interface It is a direct user interface to the FC input output FCIO interface provided by the Oracle StorEdge SFS The FCIO interface provides an Oracle common ioctl interface to the FC transport library FCTL which mana
48. s forced the Fibre Channel link to be reset SEVERITY LEVEL Notice MESSAGE Link reset ACTION No action needed informational Emulex Drivers for Solaris User Manual Page 27 gt G EMULEX MSG_ID 0731 ERROR Link reset failed VERBOSE_MASK LOG_LINK 0x00000080 or LOG_SFS 0x00002000 DESCRIPTION This indicates that an attempt to reset the Fibre Channel link has failed SEVERITY LEVEL Error MESSAGE Link reset failed ACTION No action needed informational However if the problem persists report this error to your customer service representative ELS Events MSG_ID 0800 DEBUG ELS sent VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that an ELS command is being sent SEVERITY LEVEL Debug MESSAGE ELS sent ACTION No action needed informational MSG_ID 0801 DEBUG ELS comp VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that an ELS command completed normally SEVERITY LEVEL Debug MESSAGE ELS comp ACTION No action needed informational MSG_ID 0810 ERROR Stray ELS completion VERBOSE_MASK LOG_ELS 0x00000100 DESCRIPTION This indicates that an ELS command completion was received without issuing a corresponding ELS command This error could indicate a driver or firmware problem SEVERITY LEVEL Error MESSAGE Stray ELS completion ACTION No action needed informational However if the problem persists report this error to your customer service representative
49. ssumes no responsibility for its use nor for any infringements of patents or other rights of third parties that may result Periodic changes are made to information contained herein although these changes will be incorporated into new editions of this manual Emulex disclaims any undertaking to give notice of such changes Emulex 3333 Susan Street Costa Mesa CA 92626 Emulex Drivers for Solaris User Manual Page ii Intro CU COUN OIE xe cea ets ss ect ce wn vse sto nee ts me ts cee eee 1 Important CONSideratiONS cece ee aaa aaa aaa aaa 1 New in This REIS ASE sicieieetsaicn ieiceocelind elles tae anenncgetiecane da daleoc iiie aia valida aA aiaia 1 KNOWN ISSUCS sicaire 1 Driver Information FO nannaa anaana edad AAAA aeiaai 1 FNS TS CMS IOS ct ccc E E E ccc cc ccc E 1 GON etIOIN TEs 2 as che ce hc sxe ce cece ches A ors cheese cee eect 1 Installing the Drivers 2 c2e tise dintia taal ea aa 2 Installing the Out of Box Drivers for Solaris 10 ANd 11 0 cccceeeeeeeeeeeeeees 2 Uninstalling the Drivers cccccceeeeeeeeeeeceaeeeeeeeeeeeeeeeaaeaeeeeeeeeeeeaaaaaeeeeeeeeeesaaaeneeeeeess 2 MUU S ieee ceca sna mi eee ect E e cause tent ecbuucarbceeertcucsunaznn cece ceceseuacaen centre eunnaaanne 2 The OneCommand Manager Application cccccccecseeeeeeeeeeeeeeeeeteeeeeeetee 2 Teemad WTI esseen AAA 3 The cmkan UUN eonen rennen renn onenn Ene E O E 3 FC Configuration and Migration c cccccccccceeccceeeeeeeee
50. ual port with a mounted file system e Due to the limitation of the Solaris Leadville stack deleting a virtual port causes that virtual port to go offline e The Emulex LightPulse LP11000 and LPe11000 family of adapters can support up to 100 virtual ports e The Emulex LightPulse LPe12000 family of adapters can support up to 255 virtual ports NPIV and OS Virtualization Solaris has several OS virtualization solutions including Oracle VM for SPARC Oracle VM for x86 and containers Devices configured to be seen on an Emulex FC port either a physical port or a virtual port can be used with any of these OS virtualization solutions Emulex strongly recommends that you consult the latest document on these technologies to learn the best use of resources related to NPIV technology Using VPorts with Oracle VM Server for SPARC Containers and Oracle VM Server for x86 To use NPIV with Oracle VM Server for SPARC formerly Logical Domains Solaris containers or Oracle VM Server for x86 formerly xVM user domains 1 Create virtual ports for the domains containers to which you want to present dedicated storage 2 Discover and attach the targets to the virtual ports 3 Assign the target to the domain or container The attachment runs through the virtual port that provides the path to the target Emulex Drivers for Solaris User Manual Page 5 gt G EMULEX Configuring Target Mode Support for Solaris 11 Target mode support is only avai
51. uture use LOG_FCT_DETAIL 0x00800000 Detailed FCT events LOG_FCSP_DETAIL 0x01000000 Detailed FCSP events LOG_NODE_DETAIL 0x02000000 Detailed node events LOG_IOCTL_DETAIL 0x04000000 Detailed IOCTL events LOG_IP_DETAIL 0x08000000 Detailed IP events LOG_FIRMWARE_DETAIL 0x10000000 Detailed Firmware events LOG_SFS_DETAIL 0x20000000 Detailed Solaris SFS events LOG_MBOX_DETAIL 0x40000000 Detailed Mailbox events LOG_SLI_DETAIL 0x80000000 Detailed HBA SLI events LOG_ALL_MSG OXFFFFFFFF Detailed Node events Emulex Drivers for Solaris User Manual Page 13 gt G EMULEX Severity Levels Table 4 Severity Levels Level Message Description DEBUG Informational Message provides engineering debug information NOTICE Informational Message provides a general purpose information WARNING Message provides a general purpose warning ERROR Message indicates that a driver error has occurred PANIC Severe Message indicates that the driver has forced a system panic to occur Message Log Example The following is an example of a message on the system console 5 0336 elxfc0 NOTICE 720 Link up 1Gb fabric The following is an example of the same message in the system message log var adm messages file Jan 19 14 45 36 sunv240 elxfc ID 349649 kern info 5 0336 elxfcO NOTICE 720 Link up 1Gb fabric In the above system log message Jan 19 14 45 36 unidentified the date and time when
52. will be retried by the upper layer SEVERITY LEVEL Notice MESSAGE Packet transport failed ACTION No action needed informational MSG_ID 0931 ERROR Packet transport error VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an error occurred while attempting to send an I O packet The I O packet will likely be failed back to the user application SEVERITY LEVEL Error MESSAGE Packet transport error ACTION No action needed informational However if the problem persists report this error to your customer service representative MSG_ID 0932 DEBUG Packet transport VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This provides additional information about a packet being sent SEVERITY LEVEL Debug MESSAGE Packet transport ACTION No action needed informational MSG_ID 0940 DEBUG Packet completion error VERBOSE_MASK LOG_PKT 0x00000200 DESCRIPTION This indicates that an I O packet was completed with an error status This can occur during normal operation SEVERITY LEVEL Debug MESSAGE Packet completion error ACTION No action needed informational However if the problem persists report this error to your customer service representative FCP Traffic Events MSG_ID 1000 DEBUG Stray FCP completion VERBOSE_MASK LOG_FCP 0x00000400 DESCRIPTION This indicates that an FCP command completion was received without issuing a corresponding FCP command This error could indicate a driv

Emulex Drivers for Solaris FC version 2.75h User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents