Explorer firmware update USER MANUAL
Contents
1. Jois EXPLORER FIRMWARE UPDATE USER MANUAL Jouuis EXPLORER FIRMWARE UPDATE SPORT REBREATHER CONTENTS RO 2 A ass A E A 3 SOFTWARE INSERTION tei fps aint ncaa 4 OPTOCON 4 OPERA TION enore a n e N A A Is ee Nas 4 A 224222 Teer ere ree ee ee ee 4 Hollis 2014 2 Doc 12 4148 r01 3 17 14 Jouuis EXPLORER FIRMWARE UPDATE PORT REBREATHER NOTICES LIMITED WARRANTY For details refer to the Product Warranty section on the Hollis web site www HollisGear com COPYRIGHT NOTICE This operating manual is copyrighted all rights are reserved It may not in whole or in part be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form without prior consent in writing from Hollis Explorer Firmware Update User Manual Doc No 12 4148 O Hollis 2014 San Leandro CA USA 94577 510 729 5110 TRADEMARK TRADE NAME AND SERVICE MARK NOTICE HOLLIS the HOLLIS logo type and Hollis Explorer are registered and unregistered trade marks trade names and service marks of HOLLIS All rights are reserved O Hollis 2014 Doc 12 4148 r01 3 17 14 Jouuis EXPLORER FIRMWARE UPDATE SPORT REBREATHE SOFTWARE INSTALLATION 1 The Optocon USB cable supplied with the EXPLORER requires installation of Virtual COM port software Download the drivers from http www silabs com products mcu pages usbtouartbridgevcpdrivers aspx following the link to Download VCP for Window2. s XP Server 2003 Vista 7 8 Open the downloaded zip file and run CP210xVCPIn staller_x64 exe on a 64 bit machine or CP210xVCPinstaller_x86 exe on a 32 bit machine accept the license agreement click Next gt and Finish 2 Download the EXPLORER Reprogramming Application from http www hollis com support software OPTOCON The technology used for reprogramming the EXPLORER is opti cal The Optocon port on the EXPLORER s LSS Module is very sensitive to light and reprogramming the EXPLORER will be much slower and may not even work at all if the ambient light is too bright If at all possible reprogram the EXPLORER in a dark room or at least with the Optocon port shielded from direct light OPERATION 1 The sensor module must be placed on top of the LSS before attempting a firmware update Fig 7 2 connect the Optocon cable 3 Power on the the Explorer handset 4 Run the EXPLORER Reprogramming Application from Start All Programs EXPLORER Reprogramming Application or the desk top shortcut if that option was chosen in the installer Follow the actions given in the application Fig 2 noting that context sensitive help is given on the Help property sheet with Versions Changes and Log OPERATIONAL NOTES 1 The first time the EXPLORER Reprogramming Application is run with an EXPLORER connected your Windows firewall will detect network access by the application Use the option to unblock the application otherwi
3. se reprogramming will not be possible Hollis 2014 Fig 1 Switch on EXPLORER and connect to PC via Optocon USB cable EXPLORER Connecting IO v M w h Fig 2 Doc 12 4148 r01 3 17 14 Jouuis EXPLORER FIRMWARE UPDATE SPORT REBREATHER 2 If new software is available for your EXPLORER a message will be given to press CONTINUE on the Handset Fig 3 Use a short push on the right button to begin reprogramming If MEW SOFTWARE reprogramming isn t wanted exit the programming application e and then choose DON T UPDATE with a short push on the left AY button 3 During reprogramming a progress screen will be shown Fig 4 Operation of the software is indicated by progressive lighting of the white squares on the bottom of the screen continuously Optocon USB connection activity is indicated by rotation of the Fig 3 single square at the top of the screen Total progress is given by the green progress bar Fully reprogramming the system can take up to 30 minutes 4 Context sensitive help will always be available in the Help tab of the application 5 Once the Firmware has been updated the handset must be turned off before the desktop software application may be exited Fig 4 Hollis 2014 Doc 12 4148 r01 3 17 14
Download Pdf Manuals
Related Search