E-flite logo - Scorpio
Contents
1. Elite Power 32 Brushless Outrunner Instructions The Power 32 is designed to deliver clean and quiet power for 30 to 36 size sport and scale airplanes weighing 3 5 to 6 pounds 1 6 to 2 7 kilograms 25 to 36 size 3D airplanes up to 4 5 pounds 2 kilograms or models requiring up to 700 watts of power It is especially a good match for 25 size 3D airplanes such as the E3D Power 32 Brushless Outrunner Features e Equivalent to a 30 to 36 size glow engine for sport and scale airplanes weighing 3 5 to 6 pound 1 6 to 2 7 kilograms e Ideal for 25 to 36 size 3D airplanes up to 4 5 pounds 2 kilograms e Ideal for models requiring up to 700 watts of power e High torque direct drive alternative to inrunner brushless motors e Includes mount prop adapters and mounting hardware e Quiet lightweight operation e External rotor design 5mm shaft can easily be reversed for alternative motor installations e High quality construction with ball bearings and hardened steel shaft e Slotted 12 pole outrunner design Power 32 Specifications Diameter 42mm 1 7 in Case Length 50mm 1 9 in Weight 200g 7 oz Shaft Diameter 5mm 2 in EFLM4032A Kv 770 roms per volt lo 2 4A 10V no load current Ri 02 ohms resistance Continuous Current 42A Max Burst Current 60A Watts up to 700 Cells 10 14 Ni MH Ni Cd or 3 4S Li Po Recommended Props 11x7 to 14x7 Brushless ESC 45 60 Amp Maximum Operating Temperature 2202. EFLA110 Power Meter measures power output in amps volts watts and capacity EFLA241 Gold Bullet Connector Set 3 5mm 3 EFLA249 Gold Bullet Connector Set 4mm 3 EFLM1926 Prop Adapter w Collet 6mm Reversing the Shaft This Outrunner motor has a shaft which exits through the rotating part of the motor If you want to reverse the shaft to exit through the fixed part of the motor follow these instructions carefully for changing the shaft installation NOTE The user assumes all liability for damage that may occur Loosen the set screw on the shaft collar and remove the collar from its location against the bearing Remove the small black donut washer that rests against the bearing Loosen the two set screws in the rotating part of the motor Slide the shaft through the motor It may be necessary to use a small hammer to lightly tap the shaft It is very important that you do not bend the shaft in this process so use extreme caution to assure this does not happen Re install the donut washer against the bearing Do not skip this step Re install the shaft collar back against the washer and bearing Retighten all setscrews making sure you line up with the flat spot on the shaft ee ae ol prp Replacement shafts are available separately Order EFLM40321 for a Power 32 BL Outrunner shaft Operating Instructions 1 This brushless motor requires the use of a sensorless brushless speed control Failure to use the correct speed control
3. degrees Fahrenheit Adequate cooling is required for all motor operation at maximum current levels Maximum Burst Current duration is 30 seconds Adequate time between maximum burst intervals is required for proper cooling and to avoid overheating the motor Maximum Burst Current rating is for 3D and limited motor run flights Lack of proper throttle management may result in damage to the motor since excessive use of burst current may overheat the motor Note The 3 5mm Gold Bullet Connectors included on this motor are rated for current up to 60A Please see our accessory parts listed below for 4mm connector option if you are running more current than we recommend Determine a Model s Power Requirements 1 Power can be measured in watts For example 1 horsepower 746 watts 2 You determine watts by multiplying volts times amps Example 10 volts x 10 amps 100 watts Volts x Amps Watts 3 You can determine the power requirements of a model based on the Input Watts Per Pound guidelines found below using the flying weight of the model with battery 50 70 watts per pound Minimum level of power for decent performance good for lightly loaded slow flyer and park flyer models 70 90 watts per pound Trainer and slow flying scale models 90 110 watts per pound Sport aerobatic and fast flying scale models 110 130 watts per pound Advanced aerobatic and high speed models 130 150 watts per pound Lightly loaded 3D mode
4. of the user to monitor the temperature and prevent overheating Overheating of the motor is not covered under any warranty 7 You can install the propeller on the motor shaft after you have confirmed proper rotation direction Also consult the instruction included with your sensorless electronic speed control for proper adjustments and timing 8 Once the battery is connected to the motor please use extreme caution Stay clear of the rotating propeller since spinning propellers are very dangerous as the motors produce high amounts of torque 9 Never disassemble the motor This will void any warranty Safety Precautions This is a sophisticated hobby product and not a toy It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision The Outrunner motor case is a rotating part so use extreme caution Please read the warning information included with your propellers for safety information related to the operation of motors with propellers Failure to comply with these warnings and or improper use of propellers may result in serious injury Installation NOTE Photo shows typical installation of motor and x mount directly to the outside of the firewall There are other options available including mounting
5. responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision The product manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or injury Questions Assistance and Repairs Your local hobby store and or place of purchase cannot provide warranty support or repair Once assembly setup or use of the product has been started you must contact Horizon Hobby Inc directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance Questions or Assistance For questions or assistance please direct your email to productsupport horizonhobby com or call 877 504 0233 toll free to speak to a service technician Inspection or Repairs If your product needs to be inspected or repaired please call for a Return Merchandise Authorization RMA Pack the product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon Hobby Inc is not responsible for merchandise until it arrives and is accepted at our facility Includ
6. A THP60003S3PPL 6000mAh 3S3P 11 1V Li Po 18GA THP60004S3PPL 6000mAh 4S3P 14 8V Li Po 18GA Examples of Airplane Setups Please see our web site for the most up to date information and airplane setup examples NOTE All data measured at full throttle Actual performance may vary depending on battery and flight conditions E3D 25 size Option 1 Motor Power 32 ESC Castle Creations Phoenix 60 Standard settings with 9V Soft Li Po cut off and no brake CSEPHX60 Prop APC 15x8E APC15080E Battery Thunder Power PRO LITE 6000mAh 3S3P THP60003S3PPL Flying Weight w Battery 3 5 lbs Amps Volts Watts Input Watts Pound RPM 46 0 10 4 480 137 5880 Expect strong power for unlimited aerobatics and 3D flying Speed is good and vertical is strong There is plenty of power for any aerobatic and 3D maneuvers Average duration is approximately 12 18 minutes depending on throttle management 36 size 3D ARF Option 1 Motor Power 32 ESC Castle Creations Phoenix 60 Standard settings with 12V Soft Li Po cut off and no brake CSEPHX60 Prop APC 13x6 5E APC13065E Battery Thunder Power PRO LITE 4200mAh 4S2P THP42002S2PPL x 2 in series Flying Weight w Battery 4 3 lbs Amps Volts Watts Input Watts Pound RPM 50 5 13 9 705 165 8800 Expect excellent power for unlimited aerobatics and 3D flying Speed is good vertical is very strong There is plenty of power for any aerobatic and 3D maneuvers Average duration is approximately 10 12 minutes
7. ack is approximately 10 volts and a 3 cell Li Po pack is approximately 9 9 volts Due to variations in the performance of a given battery the average voltage under load may be higher or lower These however are good starting points for initial calculations Model E3D 25 size ARF Estimated Flying Weight w Battery 3 5 lbs Total Input Watts Required for Desired Performance 455 minimum Motor Power 32 Max Continuous Current 42A Max Burst Current 60A Cells Li Po 3 3 Cells Continuous Power Capability 9 9 Volts 3 x 3 3 x 42 Amps 416 Watts 3 Cells Max Burst Power Capability 9 9 Volts 3 x 3 3 x 60 Amps 594 Watts Per this example the Power 32 motor when using a 3S Li Po pack can deliver up to 594 watts of input power readily capable of powering a 25 size 3D ARF with the desired level of performance requiring 455 watts minimum You must however be sure that the battery chosen for power can adequately supply the current requirements of the system for the required performance Battery Choices We recommend Thunder Power Li Po batteries for the best performance and lowest weight in some cases Ni MH 1800 2200mAh high discharge packs also make good alternatives at the expense of weight and lower capacity Some examples of the packs we recommend for use with the Power 32 motor can be found below THP42002S2PPL 4200mAh 2S82P 7 4V Li Po 13GA THP42003S2PPL 4200mAh 3S2P 11 1V Li Po 18GA THP60002S3PPL 6000mAh 2S3P 7 4V Li Po 13G
8. bby com 2006 Horizon Hobby Inc
9. depending on throttle management Option 2 Motor Power 32 ESC Castle Creations Phoenix 60 Standard settings with 9V Soft Li Po cut off and no brake CSEPHX60 Prop APC 15x8E APC15080E Battery Thunder Power PRO LITE 4200mAh 3S2P THP21003SPL x 2 in parallel Flying Weight w Battery 3 9 Ibs Amps Volts Watts Input Watts Pound RPM 52 0 10 48 545 140 6100 Expect strong power for most maneuvers and good vertical There is good power for any aerobatic and mild 3D maneuvers The acceleration out of a hover is positive but slow Average duration is approximately 10 12 minutes depending on throttle management Option 3 Motor Power 32 ESC Castle Creations Phoenix 60 Standard settings with 12V Soft Li Po cut off and no brake CSEPHX60 Prop APC 15x8E APC15080E Battery Thunder Power Gen II 4200mAh 3S2P THP21003S x 2 in parallel Gen II batteries have been replaced by PRO LITE Flying Weight w Battery 3 9 lbs Amps Volts Watts Input Watts Pound RPM 44 4 9 8 435 115 5960 Expect good power for most maneuvers and decent vertical but not unlimited vertical This setup delivers very good power for sport and aerobatics Average duration is approximately 10 minutes depending on throttle management Accessories See our web site at www E fliteRC com or www horizonhobby com for our complete line of brushless motors We have posted a specification comparison sheet on our web site so you can compare the different motors we offer
10. e your complete name address phone number where you can be reached during business days RMA number and a brief summary of the problem Be sure your name address and RMA number are clearly written on the shipping carton Warranty Inspection and Repairs To receive warranty service you must include your original sales receipt verifying the proof of purchase date Providing warranty conditions have been met your product will be repaired or replaced free of charge Repair or replacement decisions are at the sole discretion of Horizon Hobby Non Warranty Repairs Should your repair not be covered by warranty and the expense exceeds 50 of the retail purchase cost you will be provided with an estimate advising you of your options You will be billed for any return freight for non warranty repairs Please advise us of your preferred method of payment Horizon Hobby accepts money orders and cashiers checks as well as Visa MasterCard American Express and Discover cards If you choose to pay by credit card please include your credit card number and expiration date Any repair left unpaid or unclaimed after 90 days will be considered abandoned and will be disposed of accordingly Motors requiring inspection or repair should be shipped to the following address freight prepaid Horizon Service Center 4105 Fieldstone Road Champaign Illinois 61822 E flite is an exclusive brand of Horizon Hobby Inc 877 504 0233 www E fliteRC com www horizonho
11. enance or attempted repair by anyone other than an authorized Horizon Hobby Inc service center This warranty is limited to the original purchaser and is not transferable In no case shall Horizon Hobby s liability exceed the original cost of the purchased product and will not cover consequential incidental or collateral damage Horizon Hobby Inc reserves the right to inspect any and all equipment involved in a warranty claim Repair or replacement decisions are at the sole discretion of Horizon Hobby Inc Further Horizon Hobby reserves the right to change or modify this warranty without notice REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER HORIZON HOBBY INC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES As Horizon Hobby Inc has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of this product you are advised to return this product immediately in new and unused condition to the place of purchase Safety Precautions This is a sophisticated hobby product and not a toy It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this product in a safe and
12. ls and ducted fans 150 200 watts per pound Unlimited performance 3D models NOTE These guidelines were developed based upon the typical parameters of our E flite motors These guidelines may vary depending on other motors and factors such as efficiency and prop size 4 Determine the Input Watts per Pound required to achieve the desired level of performance Model E3D 25 size ARF Estimated Flying Weight w Battery 3 5 lbs Desired Level of Performance 130 150 watts per pound Lightly loaded 3D models 3 5 Ibs x 130 watts per pound 455 Input Watts of total power minimum required to achieve the desired performance 5 Determine a suitable motor based on the model s power requirements The tips below can help you determine the power capabilities of a particular motor and if it can provide the power your model requires for the desired level of performance Most manufacturers will rate their motors for a range of cell counts continuous current and maximum burst current e In most cases the input power a motor is capable of handling can be determined by Average Voltage depending on cell count x Continuous Current Continuous Input Watts Average Voltage depending on cell count x Max Burst Current Burst Input Watts HINT The typical average voltage under load of a Ni Cd Ni MH cell is 1 0 volt The typical average voltage under load of a Li Po cell is 3 3 volts This means the typical average voltage under load of a 10 cell Ni MH p
13. may result in damage to the motor and or speed control 2 When mounting the motor be sure the correct length of screws are used so damage to the inside of the motor will not occur We suggest you use the mounting hardware included with your motor The use of long screws will damage the motor 3 You may connect the three motor wires directly to the controller with solder or use connectors such as gold plated brushless bullet connectors EFLA241 which will also need to be soldered properly to your wires The three motor wires can be connected in any order to the three output wires or output port on a sensorless brushless speed control Be sure to use heat shrink tubing to properly insulate the wires so the wires will not short Shorting may damage the motor and speed control 4 If you add connectors and you no longer wish to use them never cut the motor wires Remove them by properly desoldering them Shortening the motor wires is considered an improper modification of the motor and may cause the motor to fail 5 When you connect the motor to the esc check the rotation direction of the motor If you find the rotation is reversed switching any two motor wires will reverse the direction so the motor rotates properly 6 Proper cooling of the motor is very important during operation New technology has brought much higher capacity batteries with higher discharge rates which can cause extreme motor temperatures during operation It is the responsibility
14. the motor inside the fuselage requires reversing the shaft direction or extending the motor further forward using aftermarket mount extensions when using cowls 1 You can first trial fit the aluminum x mount against the front of the firewall and use a Sharpie to mark the locations of four holes and drill appropriate size hole to fit the blind nuts provided Always be sure to maintain the proper thrust line and account for adequate prop spinner clearance 2 Attach aluminum x mount to the outrunner motor using the four flat head countersunk screws provided with the motor 3 Install four blind nuts on the inside of the firewall 4 Attached the aluminum x mount and motor to the outside of the firewall using the four socket head cap screws and washers Limited Warranty Period Horizon Hobby Inc guarantees this product to be free from defects in both material and workmanship for a period of 1 year from the date of purchase Limited Warranty amp Limits of Liability Pursuant to this Limited Warranty Horizon Hobby Inc will at its option i repair or ii replace any product determined by Horizon Hobby Inc to be defective In the event of a defect these are your exclusive remedies This warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modification of or to any part of the Product This warranty does not cover damage due to improper installation operation maint
Download Pdf Manuals
Related Search