CAL ET2412 ON/OFF HEAT CONTROLLER 2 1
Contents
1. PYES Can be modified P no Visible but can t be modified C55c C1 set value security access level PYE 5 Can be modified P no Visible but can t be modified level PYES Can be modified P no Visible but can t be modified The Hyde Business Park Brighton East Sussex BN2 4JU United Kingdom Tel 44 o 1273 606271 CAL www west cs com Fax 44 0 WEST Control Solutions 1273 609990 212 ET2412 E 01 1510122. BN2 4JU United Kingdom www Tel 44 0 1273 606271 west cs com Fax 44 0 1273 609990 TECHNICAL SPECIFICATIONS INPUT Scale Range 60 0 150 0 C 76 0 302 0 F ENVIRONMENTAL CONDITIONS Ambient Storage temperature 0 50 C 25 70 C without icing Relative Humidity Max humidity 80 for temperatures up to 31 C decreasing linearly to 50 relative humidity at 40 C Protection Class According to EN60529 Front panel IP65 Rear panel IP20 Height Max 2000m Do not use the device in locations subject to corrosive and flammable gasses ELECTRICAL CHARACTERISTICS Input Type NTC Sensor Resistance Accuracy EN 60751 1 for full scale 1 Digit Supply 230V AC 10 20 50 60Hz or 12 24V AC DC 10 Power Consumption Max 3VA Wiring Power connector 2 5mm screw terminal Signal connector 1 5mm screw terminal conenction Line Resistance Max 1000hm Data Retention EEPROM Min 10 years EMC EN 61326 1 2013 Performance criterion B is satisfied for EN 61000 4 3 Safety Requirements EN 61010 1 2012 Pollution degree 2 overvoltage category Il Indicator 4 digits 12 5mm 7 segment red LED OUTPUT gt C1 Output 250V AC 8A for resistive load NO and NC control output A1 Output 250V AC 8A for resistive load NO control output Life Expectancy for Relay 30 000 000 Switching for no load operation 300 000 switching for 8A resistive load at 250VAC CONTROL Single setpoint and alarm cont
3. is appeared and temperature setpoint adjustment mode is entered SET then Programming Menu is entered Default v Value for C1 output C iL L Control set point lower limit It can be adjusted between 60 0 and L IHL parameter value cr or C IHL Control set point upper limit for C1 output Aav It can be adjusted between 150 0 and C iit parameter value C HY Output hysteresis value It can be adjusted between 0 1 and Av 20 0 C A v ERROR MESSAGES Sensor is broken Temperature value is higher than the scale Temperature value is lower than the scale Modification Of Parameter Diagram SET r A y Default y 60 A iL L Control set point lower limit for 2 A1 output Ai ouput A 1k Y P E Y Alarm type selection While holding down a key parameter value blinks and by y A using keys the requested value can be adjusted If A key is pressed and held 0 6 seconds the value of the selected parameter increases rapidly If waited enough the value increases a hundred at each step After 1 second following the release of the key initial increasing condition is returned The same procedure is valid for the decrementing C1 Set value A1 Set value Temperature setpoint value is adjusted with A y buttons then when one of these buttons are pressed for the first time blinking setpoint value appears Value AY It can be adjusted between 60 0 and A IHL parame
4. Read this document carefully before using this device The guarantee will be expired by device demages if you don t attend to the directions in the user manual Also we don t accept any compensations for personal injury material damage or capital disadvantages CAL ET2412 ON OFF HEAT CONTROLLER Thank you for choosing CAL ET2412 ON OFF Heat Controller 77 x 35mm sized Single NTC sensor input Zero point input shift Selectable heating or cooling control for C1 relay output A1 Relay output for alarm control Selectable independent deviation and band alarm types In the case of sensor failure relay state can be set to ON or OFF 07 1 Upper and lower setpoint limits can be adjusted C ET2412 ReHS Temperature unit can be selected as C or F Compliant Order Code ET2412 1 Supply Voltage 2 Relay Current Selection 1 2 230 230V AC 08 8A Relay Output 024 24V AC DC 012 12V AC DC 7 24VAC 9 30VDC CONNECTION DIAGRAM CAL ET2412 is intended for installation within control panels Make sure that the device is used only for intended purpose The shielding must be grounded on the instrument side During an installation all of the cables that are connected to the device must be free of electrical power The device must be protected against inadmissible humidity vibrations severe soiling Make sure that the operation temperature is not exceeded All input and output line
5. is selected CEYP LooL Cooling control is selected Un E Temperature unit selection Un t Can be selected as C or F EED dP Decimal point display selection f dP no decimal value is not dotted If dP YES decimal value is dotted AY GH oF FS Offset value AY Zero point shift value is added to the measured value This feature is used for j eliminating the measuring probe distance errors It can be adjusted between 20 0 and 20 0 C ol C1 Output state in case of sensor A on Output is ON in case of sensor failure oFF Output is OFF in case of sensor failure Band Alarm Ale Y 6 AL OFF 1k Ys i SV ASV_ 0 sv j 1 i I I 0 SV C1 output setpoint ASV A1 output setpoint ASV Min 0 ASV Max 300 Default y Value AY PYES BEETS AY Codec AY AY 40 od Access code for security menu This parameter should be 412 When bco O it W keyis f pressed for 4 seconds while SET holding down B key then dPAr is seen on display and the device is returned to factory settings C tbc C Iln Security menu access level non Invisible PYE 5 Can be modified P no Visible but can t be modified A i5c RA ILn Security menu access level non Invisible PYES Can be modified P no Visible but can t be modified o 5c Conf Configuration menu access level non Invisible
6. rol On Off Control 12 bit resolution 100ms sampling time Control Type Control Algorithm AID Converter Hysteresis Adjustable between 0 1 and 20 0 C F Housing Type Suitable for flush panel mounting according to DIN 43 700 Dimensions W77xH35xD61mm Weight Approx 215g After packing Enclosure Materials Self extinguishing plastics nie cleaning the device solvents thinner benzine acid etc or corrosive materials must not be used Dimensions 77mm Depth 5mm 61mm For removing mounting clamps Push the flush mounting clamp E in direction 1 as shown in the B figure below Then pull out the clamp in direction 2 ET2412 r Connection Cable 7 Flush mounting panel 2 clamp kk ee kek Packing we Packing Flush mounting clamp gt v2 LD av Panel cut out Note 1 Panel thickness should Sm PA hie a le 71 5mm gt be maximum 7mm E9YVLZ21209089 8 E muo 1 2 If there is not 60mm free Fm NAT som eld lt E space at the back side of renoon000C NS uosrsossommmam SIOOD TVD BTM E the device itwould be eo difficult to remove it from D o N the panel l 1 2 ET2412 E 01 151012 Measured temperature SET 105 B AOON Default value A C 15E E lt A 15E EA lt J When this button is pressed CSEE message
7. s that are not connected to the supply network must be laid out as shielded and twisted cables These cables should not be close to the power cables or components The installation and electrical connections must be carried out by a qualified staff and must be according to the relevant locally applicable regulations CAL Controls www west cs com SN XXXXXXXXX GALI CAL Controls www west cs com SN XXXXXXXXK CAL Controls www west cs com SN XXXXXXXXX Bena enwosts NI MWIN eos MU DON YONI RR ennor ML TENN ALU Madein Turkey O 8 680407 1721443 Made in Turkey C 86804071721436 Madein Turkey D 86 804071721443 RKE a ayACDE ROAN C A ET AAN C e s Eo p SRR ag R ag R cig i A a ae RS in iy LS UC U2tst4tsTet7 Jefe Lohi OLII UsTel Tete honi OeII Ls Lel ef olih Equipment is protected throughout Holding screw by DOUBLE INSULATION 0 4 0 5Nm NOTE Fuse i Note SERR Sag he Switch 1 Mains supply cords shall meet the requirements of 184 253V AC q Line OC i ry 230V AC IEC 60227 or IEC 60245 50 60Hz 3VA lt 4 Neutral G i 2 In accordance with the safety regulations the power oie e HPEY supply switch shall bring the identification of the Fuse should be connected Cable size 1 5mm relevant instrument and it should be easily accessible by the operator WEST Control Solutions The Hyde Business Park Brighton East Sussex
8. ter value A HL Control set point upper limit for AY It can be adjusted between 150 0 and A iLL parameter value A IHY Atgikist histerisiz de eri 0 1 ile 20 0 C arasinda ayarlanabilir AY Please see A1 Output Format Table for settings AY A E45 A1 Output state in case of sensor failure A V on Output is ON in case of sensor failure oF F Output is OFF in case of sensor failure A1 OUTPUT FORMATS Independent Alarm A it Y in Rl Deviation Alarm A it Y d EAL ON OFF A it Y nA OFF ON A IHY E ASV ASV Min Beginning of Scale ASV Max End of Scale SV C1 output setpoint ASV A1 output setpoint Default Value HEAL CE YP Control type selection A v n h sv SV ASV 4300 3 ASV Min 300 ASV Max 300 gt t Cia gt y If no key is pressed within 3 seconds Running Mode is entered 7 gt m PA gt tie y gt If no key is pressed within 3 seconds Running Mode is entered Ls SET amp A If A key is pressed while holding down im key Entering Running Mode in Programming Mode In Programmin Mode if no keys are pressed for 20 seconds information is saved automatically and Running Mode is entered Alternatively if A and V keys are pressed together Programming Menu is entered In the Programming Menu if A key is pressed while holding SET down m key then Running Mode is entered CEYP HERE Heating control
Download Pdf Manuals
Related Search