instruction handbook for electronic double code safes
Contents
1. INSTRUCTION HANDBOOK FOR ELECTRONIC DOUBLE CODE SAFES Please read all of these instructions carefully before commencing using your safe Try all of these procedures with the door open first until you are familiar with how the safe works FEATURES High performance microprocessor ALKALINE BATTERY inner feeding 12 key membrane keyboard 10 keys with O to 9 figures 4 dedicated led and contacts for external emergency feeding in case of exhausted inner battery ON key to activate the circuit ENTER key to confirm code set and consent to the opening Internal programming key for a new personal code in some models it 1s protected with a sliding cover TWO PERSONAL OPENING CODES WHICH CAN BE SET UP DIGITS THAT CAN BE SET minimum 6 maximum 10 the ENTER and ON keys are not valid in the combination 7 2 INTRODUCTION e ALL SAFES ARE PROVIDED WITH SERVICE CODE 111111 e THE SAFE OFFERS TWO CODE TO BE SET UP WE ADVISE TO USE BOTH OF THEM TO AVOID FORGETTING THEM e Before installing the safe check that it works properly and read the instructions carefully to understand the operation Every time a key is pressed the green OK LED lights up and the buzzer sounds pressing the ENTER key causes the green OK LED to light up for correct procedures or the red ERROR LED to light up in the case of incorrect settings 3 FIRST APPLICATION e Alimentation Unscrew the co2. de 6 OPENING THE SAFE USING YOUR PERSONAL CODE e Press ON e Enter your personal code set earlier and press ENTER The green OK LED lights up for five seconds Within this time turn the knob clockwise and open the door 7 SIGNAL INDICATING THAT INTERNAL BATTERIES ARE GOING FLAT When the internal batteries begins to go flat this is indicated at the end of the opening procedure by the red BATTERY LED lighting up and a low beep tone At this point it will still be possible to open the safe a number of times Replace the internal ALKALINE batteries 8 EMERGENCY OPENING WITH INTERNAL BATTERIES FLAT If the failing batteries goes completely flat as soon as the keyboard is pressed to proceed with opening the safe e Itis necessary to use a new 9V LR61 alkaline battery externally see Pic 2 e Press the 9V battery contacts firmly on the corresponding contacts on the keyboards ensuring that they are positioned correctly the of the battery touching the bigger contact and the of the battery touching the small contact e Press ON and enter your personal code followed by the key ENTER e Turn the knob clockwise to open the door ONLY VERSIONS WITH EMERGENCY KEY OPENING WITH EMERGENCY KEY Remove the adhesive label marked with the letter E Pic 3 Insert the key and open the lock up to the stop point turn the knob clockwise and open the door By holding the door open turn
3. r new personal code min 6 max 10 digits and press ENTER 3 Start keying to confirm your personal code and to press the key Enter If you do not want to program the second code wait some seconds and a multiple tone signal shall confirm that your personal code has been stored In order to store a second code go on with following procedure at the end of item 3 within 3 seconds 4 Press the PROGRAMMING Key 5 Start keying to second personal code from 6 to 10 figures and to press the key Enter 6 Start keying to confirm your second personal code and to press the key Enter A multiple tone signal shall confirm that your codes have been stored Instruction Digital Electronic Combination doc Pag I di 2 Note To activate modify the second personal code you shall always program the first one again 5 RESETTING CODES e Is possible cancel the personal codes pressing the button PROGRAMMING and the ON button for 5 sec The first code goes on 111111 and the second code will be deactivated Note If errors have been made while setting your new code this will be indicated by the red ERROR LED lighting up and a beep Proceed in that case a new and correct their own personal code by repeating the steps under item 4 In memory was previously the code set to error a new safe 111111 Before closing the safe it is recommended to carry out a door open some evidence of initiation using its personal co
4. the knob until the emergence of full bolts and remove the key after rotated counter clockwise To replace the label E Note If the opening with key emergency is necessary for the oversight of their own personal code you must store a new code following the instructions at point 4 IMPORTANT e Should replace the batteries once a year e Even new batteries may be defective or short term Therefore in the event of a malfunction of the electronic system ensuring first of all to replace the internal batteries e The manufacturer assumes no liability for non compliance with the instructions or improper use of safe penalty decay of the guarantee pie b In the smallest models the CONTACTS PROGRAMMING key is on the top Detail of the sliding closing to protect the PROGRAMMING key SCREW TO BE REMOVED Instruction Digital Electronic Combination doc Pag 2 di 2 STICKERS KEY FOR EMERGENCY
5. ver screw and put the batteries of the type stated on the label into the proper case on the rear of the lock see picture 1 Screw again the cover screw Use only and exclusively alkaline batteries e Safety block removal remove completely without screwing it any longer the blocking black screw blocking the magnet which is marked by a proper yellow tag WARNING To screw the black screw after removing it compromises the safe operation e Test for opening using the service code 1 1 1 1 1 1 with door open and bolts extended 1 Press ON key in the service code 111111 and press ENTER The green OK LED lights up for about five seconds 2 Within this time with the green LED ON turn the knob clockwise to retract the bolts If the combination is incorrect the red ERROR LED will light up and the buzzer will sound After three attempts with incorrect codes the keyboard will be disabled for one minute and this time will be indicated by the red ERROR LED flashing After this time renewed readiness for operation will be indicated by the green OK LED lighting up and a beep 4 STORING THE PERSONAL CODE 1 With the door open and the bolts outside press the ON key and after that the PROGRAMMING key place on the inside side of the door see Picture 1 The CODE green LED lights up with a fixed light for about 10 seconds 2 Within 10 seconds start keying in you
Download Pdf Manuals
Related Search