(Fügen Sie hier ggf
Contents
1. ABC PRODUCTS by Zj Movie Teen Menu page 8 Adjustment of drive axes lock and change of direction of each axis Menu page 8 offers the ability to proceed with only one axis while any unneeded axes are locked Useful for example in very fast motion with programmed limit stops or trips that run very precise in only one axis 1 2 3 Menu Page 8 Lock with LOCK each TILT PAN ROLL drive axes All axles or Change of direction FWD REV for TILT PAN Roll 1 TILT ON axis is activated OFF axis is deactivated FWD REV change of direction for TILT axis 2 PAN ON axis is activated OFF axis is deactivated FWD REV change of direction for PAN axis 3 ROLL ON axis is activated OFF axis is de activated FWD REV change of direction for ROLL axis P15 34 Original user manual ABC ABCH by Y movistecn Menu page 9 Limiting the travel by programming two end positions for each axis Menu page 9 offers the ability to configure the movement window of the remote heads Therefore any overrunning of the planned recording area should be avoided 1 2 3 1 ne ah Tran RO Menu page 8 Limits the travel of each drive Fi axis through high low limits HIGH 3 HIGH for TILT PAN Roll Tilt Pan Clear Clear Record Tilt Pan Roll LOW LOW LOW 1 When pressing the Tilt Clear function the current position is set to 0 Start upper endpoint press T2. ABC by 7 movieroeh Remote Head P15 User Manual P15 ABC N PRODUCTS by Z movietecn Remote Head P15 Date of issue 2011 08 P15 a Original user manual ABC PRODUCTS d by Y movie Teen TABLE OF CONTENTS 1 Eduipment Information 1 1 Contents of 2 axis unit and options 1 1a Additional contents of 3 axis unit and options 1 2 Responsibilities of the manufacturer EC declaration of conformity 1 3 Responsibilities of the operator 1 4 Exploded drawing with spare part numbers 1 5 External interfaces 1 6 Legal notice 2 User manual 2 1 To understand the user manual correctly 2 1 1 Marking on the unit 2 1 2 Markings in this user manual 2 2 Service address 3 Safety precautions 3 1 General safety precautions manufacturer 3 2 General safety precautions Use 3 3 General safety precautions Check 3 4 Intended use of P15 3 5 Personnel requirements 3 6 Safety related environmental conditions 3 7 Possible misuse 3 8 Residual hazards and protective measures 4 Technical information 4 1 Technical data 5 Structure and operation 5 1 Main components 5 2 Optional accessories 5 3 Mounting 5 3 1 Mounting P15 2 axes Base frame with drive module 5 3 2 Mounting of P15 2 axis Mounting of camera plate 5 3 3 Mounting the power cable BUS for 2 axis 5 3 4 Mounting of box zoom focus module for 2 axis operation 5 3 9 Mounting of P15 3 axis 5 3 6 Mounting the power cable BUS for 3 axis installation 9 3 1 Mounting
3. Pantographs Hoists Telescopes Trolleys TE AD SG KA 3 Ys As w v BZ fi DANA ra AT www lastro de Rail systems Studio and stage engineering
4. and disassembly and during operation please see chapter structure and special warnings for each operating phase Warning labels on the product and the manual must be observed e Ensure and guarantee the safe fixing of a camera on the remote head before each use Use additional straps for safe fixing e Electrical equipment like monitors must always be protected against moisture and humidity e Never move the remote head mechanically by hand when switched on P15 12 Original user manual ABC ABCH by Y movie Teen 3 2 General safety precautions Use Follow the instructions on the use of maximum 25 kg camera weight in the 2 axis operation 15kg camera weight in the 3 axis operation Note warnings on the unit special instructions on stability and safe use Do not leave the assembled P15 unattended Secure against unauthorized use Because of the danger of a lightning strike adjust the operation when a storm approaches P15 may be used at an ambient temperature of 5 40 C Do not assemble and disassemble if the maximal permissible wind velocity exceeds 50 km h P15 is suited for studio and limited outdoor use Avoid installing in a sandy dusty wet and salty environment e Avoid dashing the remote heads against any objects and obstacles because of possible damages to materials and the drive Damaged parts above all safety related parts must be replaced by the manufacturer 3 3 General safety precautions che
5. be pressed on all 12 following menu pages If the necessary power supply cable connection to power supply or V mount adapter is 24V DC switche on the equipment by the main switch on the side of the case Menu page 4 Basis adjustment of record and return Menu page 4 You may change each menu page with the and pages To do so touch the corresponding fields with 6 7 8 9 10 11 12 1 Scroll up menu page 2 As built position of TILT axis at degrees 1 2 3 As built position of PAN axis at degrees 4 As built position of ROLL axis at degrees 5 5 Scroll down menu page 6 Focus beam As built position of the focus possible only to objectives with inbuilt motors 7 When pressing Record the record function is switched on red light off white light 8 Tally lights in the Rec mode only in connection with zoom focus module and sensor set mounted on the red light of the camera 9 RET connection function of the camera is triggered 10 Voltage indication current voltage state 11 Beam zoom position only in connection with external motors 12 Beam iris position only in connection with external motors P15 Original user manual moderate finger pressure 30 ABC PRODUCTS d by Y movie Teen Menu page 5 Adjustment of speed and ramp for the tilt pan roll function Menu page 5 offers the ability to adjust the speed of each axis Ramp value may a
6. 0 Canon standard cable set consisting of zoom cable XPin focus cable XPin Art No 8470 2900 Canon digital cable set consisting of XPin focus cable XPin Art No 8470 2800 Fujinon standard cable set consisting of XPin focus cable XPin Art No 8470 2600 Angenieux standard cable consisting of XPin focus cable XPin Illustration IE Insert module with connecting Illustration Module may be set at variable rods in the tilt positions module Fasten clamping bolts with an Allen wrench of size 2 Connect the zoom focus module over a BUS cable with the tilt axis See also display of cable connections Page 39 P15 22 Original user manual ABC PRODUCTS d by Z movie Teen 5 3 5 Mounting P15 3 axes To mount the roll axis the clamp of the tilt axis in the 2 axis operation must be removed The assembly pieces 1 are identical and can be applied for both axle variants Illustration 3 Illustration IE Bring the Module may be module roll in set at variable position for positions Fasten mounting the bolts with an Allen wrench of xx size Position the roll axis unit in such a way to ensure free rotation of the tilt and roll axes CAUTION Determine precise positioning of the weighing with the mounted camera NOTE See also mounting of the camera page 25 The maximum camera additional load is limited in the 3 axis operation to 15kg 5 3 6 Mounting the power cable bus for 3 axis See Schematic diagram Cable connect
7. 100 2 2003 Safety of machinery Basic concepts general principles for design Part 2 technical principles ISO 12100 2 2003 EN ISO 14121 1 2007 Safety of machinery risk evaluation Part 1 principles ISO 14121 1 2007 The following national or international standards or parts clauses thereof and specifications were applied Name and address of the person authorized to compile the technical documentation Mr Sigfried Kaser Mr F Strassmann Place Munich Date 16 06 2011 P15 7 Original user manual ABC PRODUCTS d by Z movistecn 1 3 Responsibilities of the operator Repair requirements Repair of the P15 is only permitted by the MovieTech AG or authorized contract partners Disposal P15 should not be disposed of in domestic waste It must be disposed of at a collection site please check with your municipality or through your dealer manufacturer The recipient address is given on the product label This provides for an environmental friendly disposal Care It is recommended to clean P15 with a damp clean cloth when dirty Avoid any caustic or corrosive cleaning agents 1 4 Exploded drawing with numbering Note Use the indicated numbers to order any spare parts P15 9 3 axis version 2 axis version P15 8 Original user manual ABC ABCH by Y movistecn 1 5 External interfaces P15 may be mounted hanging or standing upside down at a sufficiently stable carrier unit suitable
8. CTS by Z movietecn 5 Structure and operation 5 1 Main components Remote head frame2 axis Basic bracket 2 axis with mounting plate 2x 3 8 bolts Drive module pan axis with mounting pins and lock washer Drive module tilt axis P15 16 Original user manual ABC PRODUCTS by Lmovietwcn P15 Original user manual Touch screen with control unit with emergency stop buiton power on off toggle switch fastening system One man operation joy stick module One man operation focus zoom module Main control cable 20m 17 ABC ABCH by Zj movistecn Connection cable modules 2 lengths for 2 axis version 3 lengths 3 axis version Module box zoom focus power video TALLY VIDEO 12V 15V OK Roll axis unit P15 18 Original user manual ABC PRODUCTS by Lmovietwcn Roll axis control Case 2 3 axis for P15 Art No M2594 Monitor 7 TFT LCD7 HDMI Marshall 800x480 incl battery and charger Subjects to technical changes article may differ from P15 19 Original user manual ABC PRODUCTS d by Zj MevieTeen 9 3 Mounting Please open the transport case with caution Use no sharp tools such as cutters scissors etc that may cause damage to the frame parts or the cable Please control the contents delivered with the delivery slip and list For content list see page 5 6 The contents delivered include only the items illustrated In case of missing
9. IN 12 Pol 4 Control In 20 Pol 5 Power IN 24V DC 6 Roll IN 4Pol Hirose 7 Video out BNC NOTE Emergency stop Press the red emergency stop button inward in case of emergency hazardous situation When the green ring is no longer visible the emergency stop is activated When the green ring is visible the emergency stop is not activated Avoid any contact of the LCD surface with hard objects P15 28 Original user manual ABC ABCH by Y movistecn Back side of the control unit 1 Main switch 2 Fuse 10A MT NOTE Fuse Disconnect the equipment from the power The cover of the twist lock may be removed with a small screwdriver counter clockwise Replace the fuse 10A MT if defective NOTE Note the following points to protect the control unit and avoid any damages Direct sunlight Humidity splashing water Extreme cold Dust sand If protective coatings against humidity or dust are used make sure that the device heat can escape sufficiently to prevent overheating of the electronics 5 4 1 Control unit touch panel operation Operation The software of the remote head P15 features 7 menu pages Home page after switch on the ABC products logo appears Main panel Home page changes 3 seconds after switch on to the main control page SRODUCTS NOTE Menu pages are marked with the following numbers P15 Original user manual 29 ABC had 4 5 6 7 8 9 12 The record key may
10. al property damage and other important information in connection with your equipment NOTE Safety shoes Mandatory sign according to ANSI according to Z 535 3 2007 Meaning Foot protection Foot protection Fall down drop Falling down Warning sign according to ANSI according to Z aS 535 3 2007 Meaning Falling down downward movement danger to feet Fall down drop SY Danger of Bruise crush Crushing YY Crushing Warning sign according to ANSI according to Z 535 3 2007 Meaning Risk of crushing for hands bruise crush 2 2 Service address MovieTech AG Martin Kollar Str 9 D 81829 Munich E mail info movietech de www movietech de Tel 49 0 8943 68 91 3 P15 11 Original user manual ABC ABCH by Zj movierecn 3 Safety precautions 3 1 General safety precautions manufacturer e Before commissioning ensure that you have read and understood the user manual e Do not leave the assembled remote head unattended Secure against unauthorized use e The manufacturer s specified limit values must be strictly adhered to Any excess should be avoided under all circumstances e The remote head may not be assembled under the influence of alcohol drugs or other narcotics e Only qualified persons may be assigned with the assembly and disassembly and operation of the remote head If necessary the assignment must be stated in writing e Beware of possible bruising during assembly
11. ata for FOCUS smoothness speed 5 Data for IRIS smoothness speed only with external motors P15 32 Original user manual ABC ABCH by Y movistecn Menu page 7 Adjustment of Go Home function for all axes at the same time or for one axis Menu page 7 offers the ability to program a defined position for each one or all axes which may start linearly and repeatedly at the push of a button NOTE To save the Go Home function the end stops tilt high and tilt low menu page 9 of each axis must be deleted 1 2 3a b Aalb 5a b lt a TILT Fat BOLL ROLL Programming of All Go Home Tilt function of TILT PAN ROLL Home ad Home All axes or Menu page 7 ZERO ZERO ZERO Single axle Record pare Tilt home a TALLY 23 7V Pan home 8 Roll home 1 Set allto zero The current position of all axles is saved atthe push of a button and the degree indication 0 To save keep button pressed for min 2 3 seconds 2 All Go Home At the push of a button the saved position starts automatically on direct way No programmed cornering or the like possible 3a Tilt zero At the push of a button the current position of the TILT axle is saved with degree indication 0 3b Tilt Home At the push of a button the saved TILT position starts again automatically and directly after the procedure Same function for each PAN 4a b and roll 5a b axes P15 33 Original user manual
12. ck Before each use safety must be checked during operation by visual and functional testing according to DIN15999 In particular pay attention to the following criteria unusual noises during movement deformations e g bending twisting damage e g cracks corrosion missing parts e g retaining pins fasteners defective clamp functions of the adjustment mechanisms defective cables OOOOLOO In case of form changes or damages contact the manufacturer Please observe all other safety instructions in the following chapters 3 4 Intended use of P15 P15 may only be used according to its intended use P15 is designed for horizontal and vertical camera movements around the pivot point of the middle section Therefore the camera thereby must weigh between 0 5 and 25kg 15kg in the 3 axis operation Balancing the camera on all three axes is required before each use to avoid damage to the drive units P15 13 Original user manual ABC ABCH by Y movistocn 3 5 Personnel requirements The operator of P15 should be able to control both the camera picture and the P15 radius of action The operation of P15 must be always assessed in terms of the safety related aspects The responsibility for safe operation lies with the user Distances between the camera and objects must always be assessed properly in terms of safety to avoid accidents and damages You must assume a responsible approach to the product in the res
13. djust how hard or soft each axis will start and stop 1 2 3 4 5 Pan ROLL Pas 2a 2a E AR Menu page 5 You may change each menu page with the and pages To do so touch the corresponding fields with moderate finger pressure 1 The SPEED function for axis velocities is turns yellow when activated 2 The RAMP function is activated with pressure for start and stop hard or soft for increasing value for decreasing value at the same time value in 3 Data for TILT speed RAMP 4 Data for PAN speed RAMP 5 Data for ROLL speed RAMP P15 Original user manual 31 ABC ABCH by Yj movistecn Menu page 6 Adjustment of speed and smoothness for the zoom shot focus iris function Menu page 6 offers the ability to adjust the action velocity of zoom and focus or also iris ext motors Ramp value may adjust how hard or soft these functions must be 1 2 3 4 5 Menu page 6 Adjustment of the velocity speed of zoom focus iris Or handling smoothness hard or soft of zoom focusjiris 1 The SPEED function for zoom focus iris turns yellow when activated and white when not activated 2 The SMOOTH function for hard or soft driving of zoom focus iris turns yellow when activated and white when not activated for increasing value for decreasing value at the same time value in 3 Data for ZOOM smoothness speed 4 D
14. e Die Produktpalette von MovieTech konzentriert sich auf die Bereiche Kamerakr ne Dollys Lichtsysteme Remote Heads und entsprechendes Zubeh r Ziel der Movie Tech AG ist die Herstellung von professionellem Filmequipment das die Arbeit der Anwender am Set oder im Studio wesentlich erleichtert und die Umsetzung der kreativen Ideen erm glicht The MovieTech AG is based in Munich with subsidiaries in Milan and Prague As one of the leading manufacturers in its field it produces and markets products and solutions for the film industry The MovieTech product range concentrates on the areas of Camera cranes dollies remote heads and corresponding accessories as well as studio and stage techniques The MovieTech mission is the manufacture of professional film equipment that not simplifies the work of those using it on the set or in the studio but also faciliates the implementation of creative ideas MovieTech ABC PRODUCTS N MTS Media Technical System Technical Media Technical System LASTRO ENGINEERING MovieTech AG Germany Martin Kollar Str 9 81829 M nchen Tel 49 0 89 43 68 91 3 Fax 49 0 89 43 68 91 55 E Mail info movietech de MovieTech S r l Italia Viale Edison 318 20099 Milano Tel 39 0 2 22 47 00 43 Fax 39 0 2 24 41 01 63 E Mail k shore movietech de MovieTech www movietech de www movietech de www abc products de www mis germany com wy
15. for the load crane or dolly P15 is equipped with a euro mount adapter 80mm outer diameter for attachment to film devices such as dollies or camera cranes A Mitchell adapter is optionally available 1 6 Legal Notice The manufacturers specified limit values must be strictly adhered to Any excess should be avoided under all circumstances In case of accidents due to negligence or abusive use the manufacturer will not be held liable for any damage or injuries The assembly and disassembly sequence specified in the user manual must be observed Use exclusively original parts for the product s maintenance Accessories of other manufacturer may limit neither the use nor the safe use of P15 The people entrusted to operate P15 must have read and understood the original user manual of the manufacturer In case of questions regarding the safe use please contact the manufacturer Contact details may be found among other things on the CE marking on the P15 touch panel Service life of the equipment Service life span is limited by material wear and tear Therefore service life depends on frequency of use and environmental conditions to which P15 is exposed P15 9 Original user manual ABC ABCH by Yj movistocn 2 User manual Thank you for choosing P15 we are thankful for your confidence P15 allows gliding camera movements in horizontal and vertical directions We wish you much joy and success with your new ABC produc
16. ilt HIGH save position press for 3 sec Start lower endpoint press Tilt LOW save position press for 3 sec Travel is saved and limited Same function for 2 PAN and 3 ROLL NOTE To save the Go Home Function menu page 7 the end stops Tilt high and Tilt low of each axis must be deleted Only two end final positions may be saved for each axis Caution Always start slowly any saved end positions for control purposes to check the saved procedure and to avoid damage to camera If the saves procedure has not been programmed the remote head moves beyond the planned end position If necessary repeat saved procedure Again by a slow process check end position P15 35 Original user manual ABC PRODUCTS d by Y movie Teen Menu page 12 Adjusting the joystick window Menu page 12 offers the ability to adjust the size of the joystick window 1 2 Menu page 12 EE Adjusting the joystick window i h 1 Minimizing the window 2 Maximizing the window TEL HM The smaller the value the faster the remote head Record UBatt responds to the deflection TALLY RET 23 6V H movement P15 36 Original user manual ABC PRODUCTS d by Lmovietwcn 5 5 Schematic diagram Connection plan 2 axis version P15 Remote Head Hauptanschlusskabel Main Cable 2 Achsenversion 15V 12V Qut Out PAN Tilt R ckseite Backside Tilt Zoom Focus 24V Out Box Zoo
17. ions page 40 When connecting the BUS connection cable give priority to pan and tilt as in point 5 3 2 Mounting the power cable BUS for 2 axis Page 22 Additionally the following BUS cables are connected Tilt axis roll axis Roll axis zoom box P15 23 Original user manual ABC PRODUCTS by Zj movietecn 5 3 7 Mounting the zoom focus module for 3 axis operation Illustration Illustration IE Connect the Mounting bus cable tilt illustration for connection 1 zoom focus module mounting with the roll prepared connection When the zoom focus module is not in use no cable connection 1 is required Illustration IE Illustration X Connect the Push the module bus cable tilt in the side holes connection 1 Put on clamp 1 with the roll connection For the assembly of the zoom focus box first insert the filler piece 1 in the bottom bracket see Illustration 10 Then insert the connecting rods of the zoom focus box in the side holes of L bracket Tighten with an enclosed bolt The bracket is fastened by the clamping effect of the filler piece To tare the rotation of the roll axis you may change the position of the box Always tighten fixing bolt securely to clamp the box in order to prevent sliding of the zoom focus box out of the guide way CAUTION P15 24 Original user manual ABC PRODUCTS by Z movie Teen Illustration PA Illustration PP A Insert clamp as base Con
18. m Focus Box LT Cable Lens Video Fr BNC Power Out 12V Zoom Cable Roll IN yon rF nn POWER IN 24V DC Remote IN t a Control IN Touchscreen Control Kontrolleinheit E A i Bi stick Panel PAN BAR vn Joystick Zoom amp Focus single man control Netzteil 24V Adapter Power oder 2x V Mount Supply Akku Power Supply P15 37 Original user manual ABC PRODUCTS d by Zj Movie Teen 5 6 Schematic diagram Connection plan 3 axis version P15 Remote Head Hauptanschlusskabel Main Cable 3 Achsenversion PAN Tilt 15V 12V Qut Out Ruckseite Backside Roll Bus Cable 24V Out 5 mas E Zoom Focus Box 1 4 Focus T Cable Lens Video lie BNC i Out 12V Zoom Cable Roll POWER IN 24V DC Lens i IN Jo In d Roll Remote IN Roll IN Control IN Ek Joystick Panel Fees PAN BAR Netzteil 24V Adapter Power oder 2x V Mount Power Supply P15 38 Original user manual ABC ABCH by Y movistecn 6 Care of the remote heads To clean the remote head frame and drive we recommend a moderately strong air shower to remove dirt particles Clean with a microfiber cloth damp with detergent NOTE Pack the remote head in the system case only when dry 7 General notes and safety information on operation User The user manual must be read and understood by any user before commissioning the equipmen
19. mp Illustration 75 Mounting of the basic clamp Tilt with clamp and 2 x Allen screws M8 Allen wrench Do not remove the screwed stopper of the frame for safety reasons to prevent the sliding of unsecured drive module Illustration TE Mounting of the basic bracket tilt with clamp and 2 x Allen screws M 8 Allen wrench of size 3 Illustration TY Complete assembly illustration Base plate is moved horizontally and vertically 21 ABC PRODUCTS by Zj movietecn 5 3 3 Mounting the power cable BUS for 2 axis NS Illustration A The connection sockets of the tilt module are located on the bottom side of the module Illustration i Mount power cable PAN TILT Lead the cable clamp on the frame part 5 3 4 Mounting of zoom focus module for 2 axis operation The zoom focus module allows following functions for the use of one man operation or control panel e Zoom function of an objective with integrated motor e Focus function of an objective with integrated motor e Rec on off of an objective with zoom function e Ret function of angle camera moves and shows the last seconds of footage e Power cam over 12V out caution output voltage is 15V 5A e Tally function optional sensor required Caution For the use of the module and a broadcast objective with integrated motors a cable set for the manufacturer Canon Canon digital Fujinon Angenieux is required Art No 8470 270
20. nect bus p cable on roll axis B Push and zoom focus zoom focus module module in the holes C Tighten with countering screw 5 3 8 Mounting of the camera To mount camera in the 2 and 3 axis version two 3 8 bolts are included in the contents delivered Mounted accessories such as cameras should be additionally secured by professional security systems such as appropriate steel ropes or straps from falling Caution Additional safety information on page 41 The remote head must be electrically switched off for the levelling procedure The axes of the remote heads should never be moved under voltage as this may damage the transmissions or motors Make sure that the bracket of the tilt axis does not touch the base frame when rotating Perform test at low speed Illustration HE Positioning of the tilt axis Position the camera so that a levelled position in the tilt axis is created and the camera does not turn up or down The adjustment can be made via the camera base plate or L bracker 1 The height adjustment of the tilt axis in the base frame allows you to customize the frame geometry of the camera used Small camera compact volume Note The end stop positions of each axis can be programmed at the controller see page 37 menu 9 if the axis positioning could lead to contact with the base frame P15 20 Original user manual ABC ABCH by Zj movistecn Illustration PZ Positio
21. ning of the roll axis Position the camera so that a levelled position of the roll axis id created and the camera does not turn left or right Determine the necessary distance to the frame by manual rotation The counterbalance may be achieved by adjusting the zoom focus module N Avoid a too small distance between the camera and all frame parts Caution Illustration PS Always install the lock washer over the euro mount tap to secure the remote head P15 Original user manual Perform slow motion tests of the axis to determine spacing Move the axes by hand only when the unit is switched off Illustration PI3 Place the casher according to the hole pattern press down and twist counter clockwise until it stops 26 ABC PRODUCTS by Z movistecn 5 3 9 Attaching main control cable at euro taps P15 Original user manual Illustration Main control cable Art No 8470 1100 Length 20 m Connector designation Lemo Pol Illustration PX Insert main control cable until it stop Illustration PZ Bring cable in position and mind the colored marking To remove pull up the sleeve of the plug 27 ABC PRODUCTS 5 4 Control unit Touch panel Front side Control unit with touch screen 1 Touch screen 2 Adapter for attachment 3 Emergency stop button Back side of control unit 1 Switch for 12V Out not main 2 12V Out Hirose 4 Pol w 3 Remote
22. ns e Using under water e Assembly and taring of the camera with the unit is turned on e Adjusting the drive modules with the unit turned on e Connecting and disconnecting individual cables with the unit turned on e Adjusting the drive modules with the unit turned on e The touch module must be protected against humidity P15 14 Original user manual ABC PRODUCTS d by Y movie Teen 3 8 Residual hazards and protective measures Transport Storage e When transporting the P15 make sure that no point loads rest on single parts e The remote head should be stored in a dry area e The remote head may not be stored in direct sunlight e The remote head may not be transported or shipped without proper packaging e The drive modules of the remote head may not be adjusted under load Loads are always adjusted prior to disassembly according to instructions e All accessories should be disassembled for transport 4 Technical information 4 1 Technical data Remote head P15 Digital BUS Activation Motors Power supply Touch panel Velocity Dead weight Connection Frame dimensions Bearing load P15 Original user manual RS485 DC Motor 24V 24V DC LCD 4 3 TFT Display Vmax 360 Pan 2 Axle ca 4 5 Sec 2 Axle Operation 12kg 3 Axle Operation 20kg Euro mount taps 80mm Optional Mitchell adapter 2 ply frame 520x380mm Bearing load 2 axis 25kg Bearing load 3 axis 15kg 15 ABC PRODU
23. parts inform the manufacturer 5 3 1 Mounting P15 2 axes Base frame with drive modules e The socket mount of the remote head has an outer diameter of AN 80mm e Make sure that the Euro mount connection of P15 is inserted vertically CAUTION into the designated socket 80mm clamping and that this is securely closed e Make sure that the crane or dolly to be operated with the P15 is suitable for the given load e Secure amounted camera always with additional security straps Illustration MP Position the pan module in the frame and fasten the 4 Allen screws with a wrench of size 3 Illustration 0 The Pan module may move in the frame Illustration IE Illustration MT Please leave some room Tilt module for the assembly of the may be moved connection cable in height P15 20 Original user manual ABC PRODUCTS d by Lymovietwcn Illustration ME Fasten the 4 a key of size 3 5 3 2 Mounting P15 2 Axis Mounting of camera plate Note The contents delivered include 2x 3 8 bolts for the mounting of a camera base plate P15 Original user manual Allen scrwes with Illustration The basic clamp tilt is adjustable in height for the taring of the camera Tighten the bolts securely after positioning illustration 0 Install the mounting plate A Lay the connection plate in the slot B Lay the base plate C Screw star bolts from the bottom Photo cla
24. pective environment The user must familiarize himself with and understand the safety related aspects of the operation using the user manual General information for safety at work In operation the P15 entails a risk to dash the head of an actor Within the P15 radius of action only the access to the user when mounting the camera is allowed During the operation of P15 the radius of action should be kept free en Standing or sitting underneath an extension arm with a remote head P15 assembled thereon is not allowed for safety reasons Entering a prohibited area 3 6 Safety related environmental conditions The operation of P15 is suitable for the following environmental conditions e n studio operation and limited outdoor operation e Avoid installing in a sandy dusty salty and wet environment e Avoid operation under heavy rain snowfall and in a strong windy or gusty environment e The base should be even and stable for the necessary total weight loading of P15 e Always keep in mind that the pressure on a crane dolly or individual tripod legs under load if P15 is loaded increases on the ground many times e Avoid installing P15 on snow sand and swampy grounds 3 Possible misuse The following applications are not permitted for the P15 e Using cameras weighting over 25kg 2 axis 15kg 3 axis e Using with untared and insecure cameras e Using P15 for holding lighting systems e Using P15 in sandy conditio
25. t 1 1 x Drive module roll axis 2 1 x Cable bus 3 1 x L handle with base plate 4 2 x Attachment bolts 3 8 long Controls 5 One man control consisting of 1 x Attachment bar with Tripod inclusion 1 x Zoom Focus handle 1 x Joystick handle 6 1 x Holder with rocker 3 axis 7 1 x Panel with joystick zoom focus 8 1 x PanBar cable set 9 Case for 2 3 axis version 10 User manual 11 G stand for one man operation 12 Panel joystick Packed on Date Signature P15 Original user manual ABC ABCH by Y movistecn 1 2 Responsibilities of the manufacturer EC declaration of conformity EC declaration of conformity for machinery directive 2006 42 EC Annex Il 1 A The manufacturer distributor MovieTech AG Martin Kollar Str 9 D 81829 Munich hereby explains that the following product Product name P15 Manufacturer ABC products Serial number Series type name Remote head product Description P15 is a product for the photography and film industry developed to allow weightless camera movements lt conforms to all relevant regulations of the above mentioned directive and the other applied directives following including any current changes thereof at the time of declaration The following harmonized standards were applied EN ISO 12100 1 2003 Safety of machinery Basic concepts general principles for design Part 1 Basic terminology methodology ISO 12100 1 2003 EN ISO 12
26. t Before operating the equipment all electrical and mechanical parts such as cable plugs modules fixed and removable parts screws mounting plates clamps and the like must be checked for proper condition The environmental condition must be suitable for the unit operation Avoid operation with storm water humidity excessive sunlight extreme cold etc Mains used for power supply must me checked for suitability by professionals if necessary through measurements Mounted accessories such as cameras must be additionally secured by professional security systems like suitable steel ropes or straps from falling The manufacturer disclaims any liability resulting from improper and non complying with the equipment regulation handling and from inadequate environmental conditions The same applies for any liability resulting from the use of non system accessories that cause direct or indirect damages during the use of the remote heads The warranty is void when using parts not supplied by the manufacturer and have an impact on the equipment For repairs and services you must contact the manufacturer Any damage resulting from unauthorized interference to the equipment is excluded from liability P15 39 Original user manual Die MovieTech AG mit Hauptsitz in M nchen und Tochtergesellschaften in Mailand und Prag produziert und vermarktet als einer der f hrenden Hersteller Produkte und L sungen f r die Film und Fernsehindustri
27. the zoom focus module for 3 axis operation 5 3 8 Mounting of the camera 5 3 9 Attaching main control cable P15 Original user manual Page AA O O O O N N OU Ff 11 12 12 12 13 13 13 14 14 14 15 15 18 19 19 19 21 21 23 23 24 25 27 ABC ABCH by Zj movistocn 5 4 Control unit Touch panel 5 4 1 Control unit Touch panel operation 5 5 Schematic diagram Connection plan 2 axis version 5 6 Schematic diagram Connection plan 3 axis version 6 Care of the remote heads 7 General notes and safety information on operation P15 Original user manual 28 29 37 38 40 40 ABC N PRODUCTS by Y movie Teen 1 Equipment Information 1 1 Contents of 2 axis unit 10 11 12 13 14 15 16 17 18 P15 1 x Touch panel 1 x Base frame 1 x Drive module pan axis with mounting pins and lock washer 1 x Drive module tilt Axis 1 x L handle with base plate 2 x 3 8 long attachment bolts 1 x Box Zoom Focus Power Cable set Bus for 2 Axis version Set of 1 x Cable Zoom Focus Fujinon 1 x Cable set Zoom Focus Canon 1 x Cable set Zoom Focus Canon Digital 1 x Cable set Zoom Focus Angenieux 1 x set Allen wrench 1 x Main control cable Bus 20m 1x Double battery adapter V Mount 1 x User manual 1x Monitor holder with bolts 1x AC Adapter 24V Original user manual ABC PRODUCTS d by Zj movie Teen 1 1a Additional contents of 3 axis uni
28. ts P15 Your P15 has the following main features quiet propulsion system direct access to programming sliders for data thus 360 swing radius on all axes Short assembly and disassembly times Read this user manual carefully before you use your new equipment for the first time It contains all the information you need to know on the unit operation so that you avoid personal injury and property damage Carefully observe all safety instructions in this user manual Keep this user manual carefully Give this user manual to the new owner if you sell or otherwise leave the unit Inform more users on the necessity of reading and understanding the user manual before the first use 2 1 To understand the user manual correctly 2 1 1 Marking on the unit CE mark This mark means that your equipment meets the safety requirements of all applicable EU directives Dustbin This sign means that you must dispose of the unit only at a local collection site 2 1 2 Markings in this user manual Marking Meaning Draws your attention on the handling and effect of safety information P15 10 Original user manual ABC PRODUCTS d by Y movie Teen Makes you aware of a dangerous situation that can cause you significant injury or death if not avoided WARNING Makes you aware of a dangerous situation that can cause you mild to moderate injury if not avoided CAUTION Makes you aware of potenti
Download Pdf Manuals
Related Search