Stand For Small Holes
Contents
1. Setting rin Workpiece Column slider AN Flat anvil T Figu re 1 Figure 3 Stopper V attachment sold separately No 902798 NOTE Move the lever slowly If it is not moved slowly the measuring instrument and workpiece might interfere with each other causing scratching or damage m Maintenance and repairs The flat anvil can be cleaned by using a dry cloth or a cloth on which a small amount of alcohol cleanser has been applied Metal parts such as the flat anvil and brackets can easily become rusted When not using the stand for a long period time rub the stand with anti corrosive oil and store it in a cool dry place The life of the stand varies significantly depending on the usage environment Be sure to establish a maintenance schedule based on rules that accord with the conditions under which the stand is used such as frequency of use usage environment and usage method and carry out regular inspections based on this schedule 2 Mitutoyo Corporation l u oyo Kawasaki Japan http www mitutoyo co jp2. User s Manual No 99M AG026B Stand For Small Holes Series No 215 Introduction To take full advantage of this instrument read this manual thoroughly first After reading it retain this manual for future reference The product specifications and the information in this manual are subject to change without notice Warranty In the event that the Mitutoyo Comparator Stand should prove defective in workmanship or material within one year from the date of original purchase for use it will be repaired or replaced at our option free of charge upon its prepaid return to us Please contact your Mitutoyo office Export Control Compliance The goods technologies or software described herein may be subject to National or International or Japanese Export Controls To export directly or indirectly such matter without due approval from the appropriate authorities may therefore be a breach of export control regulations and the law On Various Types of Notes IMPORTANT O Type of note that provides information essential to the completion of a task You cannot disregard this note to complete the task NOTE important note is a type of precaution which if neglected could result in a decreased accuracy or instrument malfunction failure O A note emphasizes or supplements important points of the main text It also supplies information about specific situations mw Operating Environments WWH aaam IMPORTANT Use this stand carefully and in an environment in wh
3. ich the operating temperature is between 0 and 40 C and the humidity is between 30 and 70 RH with no condensation Use this stand at a site with a minimum amount of dust oil and oil mist and which is not direct exposed to sunlight Cautions on Use IMPORTANT This stand is for measuring small holes using a 526 series bore gage It cannot be used for a 511 series bore gage Be careful not to drop the stand or knock it over If the stand is dropped or bumped strongly be sure to check that it works properly before using it again Check that the clamp holder and the flat anvil base move up and down smoothly Check that screws used to attach parts are not loose Parts such as the flat anvil can easily become rusted Do not use the stand in a humid environment Do not apply a concentrated load at a single localized point as this might damage the flat anvil which could affect the measurement results Mitutoyo s warranty will become void if the stand is repaired disassembled or modified by other than Mitutoyo E Names of Parts and How to Use Them OThis stand was designed to attach a 526 series bore gage sold separately to enable a large volume of workpieces to be measured quickly and smoothly O First loosen the column slider and slide it up to the top of the column Tighten the column slider and anchor the clamp holder Turn the knob on the front of the clamp holder and anchor the bore gage Place the setting ring o
4. n the flat anvil Figure 1 O Push the lever until it reaches the stopper to raise the flat anvil fasten the flat anvil clamp and anchor the flat anvil in position Lower the clamp holder until the stylus of the bore gage is inserted into the setting ring Hold onto the clamp holder to make sure that it does not drop down suddenly Figure 2 O Loosen the flat anvil clamp and lower the flat anvil Hold onto the flat anvil to make sure that it does not drop down suddenly Return the lever to its original position and confirm that the stylus of the bore gage is inserted firmly in the setting ring Align the setting ring with the origin and place the workpiece on the flat anvil Measure the workpiece Figure 3 O The flat anvil position can be adjusted for measurement by 38 mm when a workpiece is shipped Loosen the hex screw at the base of the lever to loosen the lever and flat anvil Adjust the flat anvil to the desired height and tighten the flat anvil clamp Push the lever until it reaches the stopper and tighten the hex screw OWorkpieces with a diameter of 25 to 50 can be positioned on the flat anvil by using a V attachment No 902798 sold separately allowing even smoother and faster measurement 4 Size of clampable objects A ii 4 08 to 16 iji Bore gage i Maximum flat anvil eed f ch cH adjustment 38 mm pa Clamp holder fe WT j i
Download Pdf Manuals
Related Search