Instructions / Assembly
Contents
1. IS Where Luxury Is Affordable Op leon CEU EET AET cn B 160 Tuscany B 170 Tuscany Grande DO NOT RETURN MERCHANDISE DIRECTLY TO YOUR ORIGINAL SELLING STORE CALL MSPA AFTER SALES SERVICE CENTER FOR ANY PRODUCT QUESTIONS CONTACT US AT info the mspa com www the mspa com SAFETY INSTRUCTIONS WARNING When installing and using this electrical equipment basic safety precaution should always be followed IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS WARNING Risk of electric shock Insert the plug only to a properly grounded socket WARNING This product is provided with a ground fault circuit interrupter The GFCI must be tested be fore each use With the product operating open the service door When the product stops operating this indicates that the door is equipped with an electrical interlock Next push the test button on the GFCI and close the service door The product should not operate Now open the service door push the reset button on the GFCI and close the service door The product should now operate normally When the product fails to operate in this manner there is a ground current flowing indicating the possible risk of an electric shock Disconnect the power until the fault has been identified and corrected WARNING To reduce the risk of electric shock do not use extension cord to connect unit to electric supply provide a properly located receptacle WARNING No part of the appliance is2. if LED displays correctly and if the signal cable is connected properly 3 Press ON OFF button on the control panel open bubble function check if it operates properly 4 After doing the above steps your MSpa should be ready for use Enjoy it Any damage caused by improper storage or failure to do the checklist of reuse will void your warranty DISPOSAL 1 The marking H indicates that this product shall not be disposed with the general household waste Please contact your local community about collection points or ask your dealer 2 This product contains valuable materials that can be recycled and contribute to a sustainable enviroment 3 For recovery recycling and dismantling information for this product please visit us at www the mspa com TROUBLESHOOTING Mspa strives to provide the most trouble free spas on the market If you experience any product related problems do not hesitate to contact us or your local after sales service center Here are some helpful tips to help you to diagnose and rectify some common sources of trouble For any spare parts you need for replacement please refer to the warranty policy for replacing details For any other unknown failures out of the list please contact your national or regional MSpa service cen ter 12 Probable Causes Solutions SS O Control 4 Check that your GFCI plug is ok you must be able to see the indicator light is in red panel display PONET aloe OP C
3. should turn red 3 Then press the TEST button The indicator light should disappear 2 WARNING Do not use if above test fails 4 Press the RESET button again the indicator light should turn red The spa is now ready for use 3 C Assembly USES TSISIREZT STS IESIRETS STS TUG E gt kl 5 gt io oao o Uaa a rst Al t 8 e X K rl R 4 R B annesinin E A E 2 F 1 F 2 F 3 A Connect each piece of foam mat to make a square mat Place the heat preservation foam mat underneath the spa tub Temp barrier mat can prevent heat loss from bottom of the unit and provide better heat preservation with together of the inflatable bladder being used It is possible to install and leave the spa tub outside at a temperature below 4 C 40 F but only if the water temperature inside the pool is higher than 4 C 40 F and water in pipe is not frozen The spa tub can be operated in cold weather with temperature down to maximum 10 C 14 F if the unit is properly set up and no frozen water inside the control box pipes or spa pool It s helpful to put temp barrier mat in between the spa pool and the ground Similar mat which is made of foam material or other materials with temp barrier function can also be used B Before proceeding any further please find Joint Panel and be sure that this is whe
4. LPG emu Sometimes it can be a little bit tricky so please then try to push the RESET button several times rather panel umea Gn quick to see if this helps attends black E EEEE E N Control the pin plug connection between the control box and the control panel without any in Pig i Please also check the ends of the plug if there is some failure of one of the pins etc power at all f it still doesn t work please contact your country MSpa service center to get a new control panel and replace Power supply Please check that the power supply is ok Is there any red indication in the GFCI plug when you push the RESET button Have the ing wet or any severe humidty Please d First find out that your MSpa is connected to a 16A power supply If you have to use one extension cord connecter cable please be sure this is for 16A purpose and for eee use The cable must have minimum the same thickness as the cable from the GFCI plug into the mp Please check that your GFCI plug is not wet To avoid wet conditions please wrap it into some plastic to does not get avoid humidity and component failure warm or Pin plug connection failure Control the pin plug that all thin pin plugs are standing correctly water is too Please check water level that it must reach the water line to make sure filter pump work efficiency hot Please control the filter cartridge and water quality If the filter cartridge is dirty or old the result can be that Water lev
5. NBUB HHHS C Dealer Where Purchased Dealer Store Address Purchase Invoice with purchase date and product model cycled attached Defect Problem Description Spa Pool Cracking ControlBox Other Problems state details in the below _ IMPORTANT For Spa pool body problem Picture of defect part need to be attached along with the mail in warranty card and is MANDATORY to claim the warranty For electric part s or control box problem Send the control box to your local MSpa Service Center See the Service Center Contact List in the manual
6. NING To avoid injury exercise care when entering or exiting the spa WARNING Do not use spa immediately following strenuous exercise WARNING Prolonged immersion in CAUTION Maintain water chemistry in accordance with manufacturer s instruction Consult your physician for recommendations CAUTION The spa should not be setup or left out in temperature lower than 4 C 40 F if the heater is not activated CAUTION Do not use the spa alone CAUTION Always enter and exit the spa slowly and cautiously Wet surfaces are slippery when wet CAUTION To avoid damage to the pump the spa must never be operated unless the spa is filled to the water line marked on the inside of the spa CAUTION Immediately leave spa if uncomfortable or sleepy CAUTION Never add water to chemicals Always add chemicals to water to avoid strong fumes or violent reactions that may result in hazardous chemical spray CAUTION Place only on a surface that can withstand the floor loading requirement of your spa NOTE Please examine equipment before use Notify after service center listed on this manual for any damaged or missing parts at the time of purchase Verify that the equipment components match the model that you purchased WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits f
7. Y CAUSE PUMP FAILURE 2 PLEASE AVOID WATER SPILLAGE WHICH WILL CAUSE DAMAGE TO THE ELECTRIC PARTS Warning to avoid function failure and damage to the control system please do not operate until spa is illed with water to the minimum water mark J Place Spa Cover on the spa Screw Safety Clasps directly into Corner Beams using locking straps to locate Safety Clasp position NOTE Lock up spa cover after each use POWER PACK OPERATION Warning to avoid function failure and damage please do not operate until spa is filled with water to the low water mark It is the responsibility of the spa owner to make sure the above installation conditions are met as well as to follow the Safety and Warning Instructions Any failure and damage which may result from dry run water spillage excessive humidity or structural loading will void the warranty Control panel amp gt 1 ON OFF Button To activate power pack 2 BUBBLE Button To activate Bubbling system which has a 20 minute auto shut off for 10 minutes E feature The light of bubble Button displays green when being activated NOTE If it works more than 15 minutes and stop manually please wait more than 10 mintues to activate manually again 3 FILTER Button To activate Filtration system The light of FILTER button displays green when the filtration system is activated e 4 HEATER Button To activate Heating and Fil
8. arty is authorized to change or modify or extend the terms of this warranty Legal Rights This warranty gives you specific legal rights and you may have other rights which vary from country to country For warranty service contact see the MSpa After Service Center Contact List in the User Manual Manufactured By Oriental Recreational Products Shanghai Co Ltd 1699 Daye Road Wugqiao Fengxian Shanghai China 15 Country Address Tel Fax E mail Address Tel Fax E mail E mail warranty goldendesignsinc com Go Hot Tubs 909 212 5555 Ottawa ON Canada E mail info gohottubs com web www gohottubs com 4 l I l I l I I l I l I l I l I I l I I l l I I l I I l l l I l I I I I I l l I l l I l l I I l I I Spa MSpa Warranty Registration Card Congratulations on purchasing a quality MSpa product To get the most value from your investment please fill in the Warranty Registration Card below By submitting this form your warranty will be registered Note Incomplete form will not to be accepted and honored by MSpa Please fill out the required file with correct info Last Name First Name Mailing Address 1 Address 2 City State Province Zip Postal Code Country Phone Number Email Address Purchase Date ____ mm ___ dd _ yyyy Product Model Serial Number Find the SN underneath the control panel and on the spa pool cover e g 2G
9. cal supplementary equipotent bonding shall connect all extraneous conductive parts in Zones 0 1 and 2 with protective conductors of all exposed conductive parts situated in these zones b The measures of protection by non conducting location and by earth free equipotent bonding are not permitted c Electrical equipment shall have at least the following degrees of protection In Zone 0 IPX8 In Zone 1 IPX5 In Zone 2 IPX4 d Junction boxes shall not be installed in Zones 0 and 1 except in zone 1 where permitted for SELV circuits e In Zones 0 and 1 no switchgear and accessories shall be installed f The transformer must be located outside zone 13 IS MSpa products are designed with reliability and simplicity in mind In addition our internal Qual ity Assurance Team carefully inspects each unit thoroughly before it leaves our facility Oriental Recreational Products Shanghai Co Ltd ORPC is pleased to extend this limited warranty cover age to the original purchaser of an MSpa Product This warranty is not transferable The warranty period commences on the original purchase date through 6 12 months accordingly The Limited Warranty This warranty is subject to the obligations limitations and exclusion listed below 1 Spa pool liner twelve 12 months from original date of purchase 2 Electric Parts Control Box twelve 12 months from original date of purchase 3 Spa rigid wall frames t
10. d can be only filled out by mail All claims must be submitted to ORPC by authorized selling dealers It is essential that all submitted claims provide all of the necessary information including customer name purchase date serial product model problem and part or parts requested without this information the warranty will be invalid Warranty Cards must be completed and mailed to ORPC by authorized dealer within thirty 80 days from the original purchase date Limitations on Warranties This warranty is a limited warranty It does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse or abnormal usage or repairs not provided by ORPC autho rized service personnel to products used for commercial or rental purpose or to products used as store display models 14 Damages caused by or attributable to the following incidents are specially excluded a Any damage caused by the operation of the spa with water temperatures outside the range of 0 C 42 C 32 F 107 6 F Europe Australia or 0 C 40 C 32 F 104 F USA b Any damage caused by clogged dirty or calcified filters c Any damage that are purely aesthetic and do not hinder the function of the MSpa d Any damage to the exterior resulting from improper maintenance or any damage to the exterior attribut able to freight mishandling e Overfilling f Damage resulting from improper winterization g Damage to the spa liner resu
11. e the heating system will restart and light turns into red The FILTER button will be activated automatically at the same time The heat increase rate is maximumly 1 2 to 1 7 C 1 3 F per hour Please note that the following conditions will lead to slow and even heating without heating phenomenon Environmental temperature lower than 10 C 50 F Outdoor wind force above Gentle breeze F 3 Environmental temperature lower than 10 C 50 F and wind power above Gentle breeze F 3 Activate bubbling system when heating Spa lid is not covered or improperly covered when heating In order to conform to the safety regulations MSpa control system uses double heating elements technology When bubble filter heater functions are all on only one heating element is working which is of 675W only OORUN So you are recommended to fill spa with warm water for quick heating and energy saving Maintaining Spa Water Poor water quality can be extremely hazardous to your health We recommend you do following things A Please use filter cartridge Screw the filter onto the water inlet lower fitting on the spa wall by turning it clockwise Ws Note Two filter cartridge one is for use one is spare Note Do not use filter cartridge when only to heat water and to ensure A good heating performance To avoid that the filter cartridge get damaged you take it off when there are children in the pool or more than two persons After finis
12. eight 0 68m 27 0 73m 29 Control System 110 120V 60Hz 110 120V 60Hz Heater 675W x 2 675W x 2 Massage Air Blower 500W 500W Filter Pump AC 24V 50W AC 24V 50W Top Lid Synthetic leather with foil Synthetic leather with foil i and inflatable bladder and inflatable bladder Cord mounted GFCI GFCI Pool Cover Plastic wood Plastic wood Pool Material PVC and Synthetic leather PVC and Synthetic leather INSTRUCTIONS NOTE Ensure to check all parts are present A A Aluminium foil top lid and key 4pcs 1set B Control panel 1set C Spa Liner 1pc D Temp barrier mat 9pcs per set eee F E Drainage hose adapter 1pc 3 F Filter cartridge 2pcs pium G Repair kit 1set H Inflatable bladder 1pc Foam connection and PVC leather strip set J Joint Panel 1pc K Skirt Tpcs L Corner Beam 8pcs M Comfort Rail 8pcs N Wrench 1pc NOTE Drawings for illustration purpose only in this manual Actual product may vary Not to scale A Site Requirements WARNING The floor has to be capable of supporting the expected load WARNING An adequate drainage system has to be provided to deal with overflow water IMPORTANT Because of the combined weight of the spa water and users it is extremely important that the base where the spa is installed is smooth flat level and capable of uniformly supporting the weight for the entire time the spa is
13. el too low and filter the filter pump doesn t get enough water thru the filter to operate as it is made for cartridge dirty Please cut the power supply to your MSpa remove the filter cartridge and then restart without the filter Inlet and outlet loose If there are water leakage like tear drops it s ok for use and you only need to screw them tight Spa leakage Please check the o ring and replace if necessary and make screws tight if they loose Error code F1 F2 Filter system failure Do not use the spa Please contact your country MSpa service center FS FA in the display Error code Pin plug connection failure Please check there is no humidity inside the pin plug connection Control the pin plug that all 12 thin pin SPL amp plugs are standing correctly SPH in the SPL temperature lower than 32 F Please check if there is any water frozen inside the spa and control box use warm water to melt and display get water temperature higher than 32 F SPH abnormal SPH abnormal high temperature temperature Do not use the spa Please contact your country MSpa service center WATER PROTECTION LEVEL Warning Water protection levels of Appliance at different product zones are different see the following scheme NOTE The measured zone dimensions are limited by walls and fi xed partitions Figure 702A Zone dimensions of swimming pools and paddling pools SAFETY amp ANNOUNCEMENTS a a a A lo
14. g away for some weeks and nobody can follow up the water treatment program in your MSpa please drain out the water before leaving and take out some air pressure Spa Pool Repair If the Spa is torn or punctured use the provided Repair Patch Dry the area to be repaired apply the glue for PVC to PVC to the repair patch and then attach it onto the damaged area Smooth the surface to remove any air bubbles A secure unnoticeable repair can usually be made 11 Spa Storage Make sure all water is drained from the Spa and control box This is essential to extend the life of the spa We recommend the use of a wet dry vacuum to blow out or suck up water from the Spa pipes and Pump lines Remove the Filter Cartridge It is recommended you store the spa in its original package in a warm dry place NOTE Make sure all components are completely dry and clean before re packing Store safely in dry condition and out of sunlight Plastic becomes brittle and susceptible to breakage when exposed to subzero temperatures Freezing can severely damage the Spa Improper winterization of your Spa may void your warranty Spa checklist before unpack the unit and re use for the new season In order to have your MSpa runs smoothly and easily for another new season make sure you do the follow 1 Check if there is water in the air pipe If any water is found dry the air pipe before operating the spa tub 2 Connect control panel correctly turn on the spa tub check
15. h bathing replace the filter cartridge N B Clean your filter cartridge at least once a time after it worked continuously for 72 120 hours The filter cartridge should be replaced at least once a week depending on use Please make sure to unplug the power pack from the electrical receptacle before the following actions 1 Unscrew the filter cartridge by turning it counterclockwise 4 a 2 The Filter Cartridge can be rinsed off with a garden hose and reused However if the Filter Cartridge remains soiled f 1 2 and discolored the Filter Cartridge should be replaced Y C Change water every few days or use appropriate pool chemicals All spas require the use of pool chemicals Please consult your local pool supply retailer for more information about chemical maintenance Pay close attention to the chemical manufacturer s instructions Spa damage resulting from misuse of chemicals and mismanagement of spa water is not covered by the warranty a Water Balance we recommend maintain your water pH between 7 2 and 7 8 total alkalinity between 80 and 120ppm and free chlorine between 3 to 5ppm Use test strip to test your water chemistry before each use of the spa no less than once per week Low pH will damage to the spa and pump Damaged resulting from chemical imbalance is not covered by the warranty b Water Sanitation Water Sanitation is the responsibility of the spa owner achieved through the regular and periodic da
16. ily if necessary addition of an approved sanitizer The sanitizer will chemically control the bacteria and viruses present in the fill water or introduced during use of the spa c Use wrench to screw off water inlet and outlet for regular check and clean to make sure they are not blocked Also the use of wrench is only necessary in case of spa problems After repair or replacement assemble the spa pool and control box and then screw clockwise firmly the water inlet and outlet onto the spa pool oH water inlet and outlet Note 1 You must not use chemicals you have in your house or any leftovers from an outdoor inflated pool or a swimming pool 2 Do not use chlorine tablets but use chlorine powder and dissolve first in a bottle 3 Do not mix the water with bath oil or something like that otherwise the pool can be damaged 4 Do only use clean freshwater and not salt water that will damage the pump 10 Special Notice on Water Treatment Please read about water quality and filter in user manual Always shower before you enter your MSpa Please use test strip to test your water chemistry before each use of the spa no less than once per week The pH level must be between 7 2 and 7 8 total alkalinity between 80 and 120ppm and free chlorine between 3 to 5ppm Too low of a pH level will result in excessive wrinkles and damage to the spa pool as well as corrosion in the motor unit Too high of a pH level hard water will resu
17. installed If the spa is placed on a surface which does not meet these require ments any damage caused by improper support will void the warranty It is the responsibility of the spa owner to ensure the integrity of the site at all times Be aware of special requirements if you install the spa indoors 1 The floor must be able to withstand the capacity of the spa 2 The floor should be a non slip level surface 3 Proper drainage is essential for indoor spa installation 4 When building a new room for the spa it is recommended that a floor drain be installed 5 Humidity is naturally present with the spa installation determine the effects of airborne moisture on ex posed wood paper etc in the proposed location 6 To minimize these effects it is best to provide plenty of ventilation to the selected area An architect can help determine if more ventilation is needed NOTE Do not install the spa on carpet or other material that can be damaged by moisture B GFCI Test WARNING RISK OF ELECTRIC SHOCK The GFCI plug must be tested before each use WARNING Insert the GFCI plug into a residual current device GFCI protected power receptacle only WARNING Before inserting the plug into a power receptacle make sure the current rate of the power receptacle and the fixed wiring are suitable for the spa Contact a qualified electrician if you cannot distin guish 1 Insert the plug into the power receptacle 1 2 The indicator light
18. lt in scale incrustation e g sheets of white coagulations inside the filter pump which will lead to block and non working of the filter pump If you have any questions regarding chemicals please contact local spa and pool water treatment specialist stores It is the responsibility of the owner to properly maintain the chemical balance and sanitation of the water Mspa is not responsible for any damages that result from improperly mantained water Improper water maintenance may result in voiding the warranty Cleaning the spa Detergent residues and dissolved solids from bathing suits and chemicals will gradually accumulate in the Spa s water If there is a lot of dirt in the water try and get it out or change water and clean the pool Use a mild soap and water solution to wash the vinyl then rinse with freshwater and drain this out before you fill up your MSpa with new fresh water NOTE Do not use hard brushes or abrasive cleaners Drainage 1 Turn off all the functions on the control panel 2 Connect the drainage hose adapter onto the drainage structure and make sure it is well connected 3 Find your garden hose and connect onto the drainage hose adapter in the other end 4 Screw off the cover of the drainage structure inside of the spa pool let the water flow out of the drainage hose 5 Wait till the spa has no water flow out of the drainage hose empty the the rest of water manually and completely If you are goin
19. lting from improper chemical treatment damage to the spa resulting from exposure to extreme temperatures h Damage to the spa resulting from exposure to direct sunlight and ultraviolet rays while the spa is empty i Damage to the pump motor plumbing and components due to improper maintenance chemical treat ment or exposure j Damage resulting from failure to properly follow user s manual installation operating or maintenance instructions Also exclude are spa accessories optional including but not restricted to the following Comfort set headrests cup holder Filter cartridge Heat preservation mat Seat cushion Test trip Bubble spa overall cover Ice box Foot bath Led light Plastic wood step Any alterations to the spa will void this warranty Alterations include but are not limited to any component or plumbing change electrical conversion or addition of alternate sanitation or heating systems ORPC authorizes no other warranty beyond that specifically set forth above ORPC is not responsible or liable for indirect special or consequential damages arising out or in connection with the use or perfor mance of the product or damages with respect to any economic loss loss of or damage to property includ ing water damage loss of revenue loss of enjoyment or use costs of removal installation or other conse quential damages of whatsoever nature No agent dealer distributor or Service Company or other p
20. mperature to 38 C 100 F F Before entering a spa the user should test the water temperature with an accurate thermometer G The use of alcohol drugs or medication before or during spa use may lead to unconsciousness and in crease the danger of drowning H Obese persons and persons with a history of heart disease low or high blood pressure circulatory sys tem problems or diabetes should consult a physician before using the spa Persons using medication should consult a physician before using a spa since some medication may cause drowsiness while other medication may affect heart rate blood pressure and circulation WARNING TO REDUCE THE RISK OF INJURY Never pour water higher than 40 C 104 F into the spa pool directly WARNING The use of alcohol drugs or medication can greatly increase the risk of fatal hyperthermia Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 37 C 98 6 F The symptoms of hyperthermia include an increase in the internal temperature of the body dizziness lethargy drowsiness and fainting The effects of hyperthermia include failure to perceive heat failure to recognize the need to exit spa unawareness of impending haz ard fetal damage in pregnant women physical inability to exit the spa and unconsciousness resulting in the danger of drowning WARNING People with infectious diseases should not use spa WAR
21. or a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help If shielded cables or special accessories are required for compliance a statement must be included which instructs the user to employ them for example Shielded cables must be used with this unit to ensure compliance with the Class FCC limits SPECIFICATIONS Style No B 160 Tuscany B 170 Tuscany Grande Water Capacity Approx 860L 227gallons 1200L 317gallons Net Weight Approx 60 kgs 132 Ibs 70 kgs 154 Ibs Outside Dimensions 1 62m 64 1 93m 76 H
22. re you wish to locate your control box The first side of the spa is where the control box will be connected and located Also note the Corner Beams shall face outward with the side including bluckle plate and snap end is up otherwise the assembly will be failed finally C Slide Corner Beams onto each side of the Joint Panel Then continue attaching Skirts and Corner Beams until eight sides of the spa are in place Slide Skirt into the eighth side of the spa so that it rests on the Corner Beams Please double check and ensure that eight sides of the spa are in place D Place Comfort Rails around the top of the spa skirts Please note the shorter side of Comfort Rail shall face to the spa pool E Place the Liner inside the spa Note The pipes protruding from the Liner shall face to the Joint Panel and go through the holes of it Stretch the coloured portion of the Liner over the Comfort Rails and snap onto the metal snaps on the Corner Beams Once all eight snaps have been fixed you may have to readjust the Comfort Rails so they sit squarely on top of the Skirt Do this by undoing each snap repositioning the Foam and redoing each snap one at a time Note Push the bottom edges of the Liner tight to the Skirt to remove any wrinkles in the Liner F Connect the control box fittings to the pipes protruding from the Liner Be sure that the rubber gaskets are in place on the control box fittings Hand tighten only holding each pipe steady and twi
23. sting only the fittings Fit the foam connection pieces between the spa and control box until it hold firm Wrap the foam connection piece with the PU leather strip Don t install Mspa onto the lawn as grass may cause air pump damped and rusted which could result the air pump works improperly and will void your warranty T G Screw the control panel onto the spa fasten the ring to the pipe adaptor Precautions 1 When using the spa tub outside air pipe can not be taken off Do not use the spa tub in rains as air pump will not working properly 2 The two O ring part on the air pipe is important to get the spa tub working properly Lost of the O rings could cause air pump rusted or not working properly Missing of the O rings also affects bubbling function H Connect the pin plugs Make sure that plugs are properly matched together screw a cap and then you ll see yellow light on control panel no bent or wet for the pin inside male connector which will cause failure connection Fill the Spa Fill the spa with water from your garden hose to approximately 2 3cm again push the bottom edges of the Liner tight to the Skirt to remove any wrinkles in the Liner Continue pe filling until it reaches the area between two water lines printed inside the Spa wall 1 WARNING 1 FILL INWATER CAREFULLY ESPECIALLY FOR THE FIRST TIME OF USE WATER LEVEL MUST REACH THE MINIMUM WATER LINE BUT NOT EXCEED THE MAXIMUM WATER LINE OTHERWISE IT MA
24. t least 5 feet 1 5 m from all metal surfaces As an alternative the spa may be installed within 5 feet of metal surfaces if each metal surface is permanently connected by a minimum 8 AWG 8 4 mm2 solid copper conductor to the wire connector on the terminal box that is provided for this purpose WARNING RISK OF ELECTRIC SHOCK Never operate any electric appliance when in your spa or when your body is wet Never place any electric appliance such as a light telephone radio or television within 5 feet 1 5 m of a spa WARNING During pregnancy soaking in hot water may cause damage to the fetus Limit use to 10 min utes at a time WARNING TO REDUCE THE RISK OF INJURY A If the supply cord is damaged it must be replaced immediately by the manufacturer its service agent or similarly qualified person in order to avoid a hazard B Do not bury cord Locate cord to minimize abuse from lawn mowers hedge trimmers and other equip ment C Connect to grounded Grounding type receptacle only D The water temperature in a spa should never exceed 40 C 104 F Water temperature between 38 C 100 F and 40 C 104 F are considered safe for a healthy adult Lower water temperatures are recom mended for young children and when spa use exceeds 10 minutes E Since excessive water temperatures increase the potential for causing fetal damage during the early months of pregnancy pregnant or possibly pregnant women should lower the spa water te
25. to be located above the spa during use WARNING Parts containing live parts except parts supplied with safety extra low voltage not exceeding 12V must be inaccessible to a person in spa pool Earthed appliance must be connected to the fixed re ceptacle which is permanently connected to fixed wiring Parts incorporating electrical components except remote control devices must be located or fixed so that they cannot fall into the spa pool Attention Static shocks and how to avoid them You ll often find shocks are worst in the winter when the air outside is cold and dry They may disappear in warmer damper weather Man made floor and shoe sole materials have been main factors in most cases of shocks Static shocks can be a nuisance but are not generally a health risk Tip if the air in your room is very dry you could try keeping an open wide dish of water handy this will evaporate and moisten the air nearby Tip cotton clothes are comfortable and usually give no static problems Tip try different shoes to see if some give less problems Leather soles are often good To avoid static shocks in MSpa wet body and hands or touch metal stuff to dissipate charge before entering into MSpa WARNING The plug of spa should be more than 3 5m away from the pool DANGER Risk of Injury The suction fittings in this spa are sized to match the specific water flow created by the pump Should the need arise to replace the suction fittings or the p
26. tration system at the same time Filtration system cannot be turned off when heating 5 TEMPERATURE Button To set and display water temperature ED 6 UP Button Increase temperature amp 7 DOWN Button Lower temperatrure ES LED Display Once powered up the LED displays the current water temperature automatically NOTE The setting temperature defaults to 38 C 100 F when first plugged in NOTE Temperature adjustment ranges from 20 C 68 F to 40 C 104 F Set your desired temperature by pressing TEMPERATURE Button Note In case when leaving spa under unattended working condition you can press up 4 amp down Y buttons at the same time to lock the conttrol panel to avoid any misoperation by children To press both buttons at the same time again and after hearing sound of DI it will be unlocked The light of the HEATER button displays red when the heating system is activated Note It s normal that filtration system cannot be turned off individually when heating system is working And filtration system can only be turned off by pressing HEATER button but not FILTER button The heater does not stop heating the Spa until the current water temperature reaches the setting temperature Then the FILTER button will be off and the light of HEATER button displays green After the current water temperature drops 2 C 4 F below the set point temperatur
27. ump be sure that the flow rates are compatible WARNING Never operate spa if the suction fittings are broken or missing Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting WARNING Spray head must not be used to fill tub WARNING The outlet of soa must not be connected to any tap or fitting other than those specified WARNING Electric installations should fulfill the requirements of local standards WARNING TO AVOID THE ELECTRIC SHOCK DO NOT USE THE SPA WHEN IT IS RAINING OR THUNDERING AND LIGHTENING WARNING To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all times WARNING Water attracts children Always have the spa locked after each use WARNING Pets should be kept away from spa to avoid damage and or accidental drowning WARNING Modifications are not approved by the party responsible for compliance It could void user s authority to operate the equipment WARNING Do not switch on if there is any possibility that the water in the spa is frozen WARNING Use only approved accessories The use of non approved accessories could void the war ranty WARNING RISK OF ACCIDENTAL DROWNING Extreme caution must be exercised to prevent unau thorized access by children To avoid accidents ensure that children can not use the spa unless they are supervised by an adult WARNING RISK OF ELECTRIC SHOCK Install a
28. wenty four 24 months from original date of purchase Report damage after this time will be subject to rejection Repair replacement parts purchased by the consumer from ORPC after the original coverage has expired on the unit will carry a 90 day warranty valid with a receipt only Any item shown to be defective will be re paired at our discretion No labor coverage is included within these parts Shipping Policy Consumers are responsible for the shipping freight when return the defect parts to MSpa authorized service center or ORPC All subsidized labour costs of removal and reinstallation of parts might be subject to dealer service charges Conditions This warranty applies to the original purchaser and terminates upon any transfer of ownership ORPC s ob ligation under this warranty is only limited to replacing or repairing at ORPC s option once any part or parts of this unit which in our judgment show evidence of such defect All repairs for which warranty claims are made must be pre authorized by ORPC through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid if requested All The authorized selling dealer is responsible for all in field service work carried out on your MSpa prod uct ORPC will not be liable for results or cost of workmanship from unauthorized service persons or deal ers Warranty Registration is required Warranty Registration Car
Download Pdf Manuals
Related Search