Meteor (user)
Contents
1. spring studs in the pre drilled holes in the tipping bar IMPORTANT Always make sure that both anti tip rollers are correctly positioned before using the wheelchair The balance of the wheelchair can be adjusted by selecting from three wheel positions see FIG 9 Figure 9 IMPORTANT It is advisable that this procedure be carried out by your wheelchair supplier who should ensure that the driving characteristics meet your requirements The brakes will also need to be repositioned if you have selected an alternative wheel position see FIG 10 Loosen the two socket head cap screws Position the brake assembly on the wheelchair frame ensuring that the brake is effective Finally tighten the two socket head cap screws in the clamp to 13 55 16 26 Nm 10 12 Ibs fit IMPORTANT It is advisable that brake resetting is carried out by your wheelchair supplier After resetting check the effectiveness of the brakes by sitting in the wheelchair with the brakes applied and attempt to propel the wheels If the wheelchair moves the brakes require further adjustment 5 FOLDING THE METEOR WHEELCHAIR FOR STORAGE OR TRAVEL Release the footrest bar A from the retaining pin B and flip up the footrest bar Slide each locking pin c and lift and rotate each footrest hanger D upwards to remove see FIG 1 Release the Velcro flaps A retaining each skirt guard Remove the backrest by rotating lever B on2. DENTLY It is safer to avoid kerbs wherever possible and use ramped kerbs or slopes It is possible to take yourself up and down kerbs unaided particularly as the Meteor has been designed for active users wishing to have a high degree of independence Users can quickly become proficient and fully independent in getting up and down kerbs providing they have practised and developed a safe technique that is suited to their abilities It may be necessary for the user to obtain training advice ensuring that those more difficult manoeuvres are conducted safely and efficiently We recommend the following as being sources of training information Disability Information Service Disablement Service Centre Banstead Mobility Damson Way Fountain Drive Queen Marys Avenue Carshalton Surrey SM5 4NR Telephone 0181 770 1151 Royal Association for Disability and Rehabilitation Unit 12 City Forum 250 City Road London EC1V 8AF Telephone 0171 250 3222 Disabled Living Foundation 380 384 Harrow Road London W9 2HU Telephone 0171 289 6111 18 IMPORTANT Movement of the occupant could cause the wheelchair to tip on kerbs and steps GOING UP A KERB FORWARDS WITH AN ATTENDANT For those users who are unable to independently climb kerbs an attendant should provide assistance by pushing using the backrest pushing bar if ascending or restraining if descending whilst the occupant controls the wheels and brake operations 1 2 Make s
3. M THE FRONT GETTING OUT FROM THE FRONT SIDE TRANSFER TO A WHEELCHAIR SIDE TRANSFER FROM A WHEELCHAIR USING YOUR WHEELCHAIR DO S AND DON TS ASCENDING AND DESCENDING SLOPES ASCENDING AND DESCENDING KERBS UNEVEN SLIPPERY AND SOFT SURFACES CARE AND MAINTENANCE FACTORY FITTED OPTIONS ACCESSORIES SERVICE HISTORY WARRANTY METUSA 1 INTRODUCTION The Meteor is a lightweight active user wheelchair designed to combine rigidity with a high degree of manoeuvrability The Meteor is intended for everyday indoor and outdoor use by an adult whose weight should not exceed 102Kg 16 stone Primarily for use and control by the occupant it has 61cm 24 diameter quick release rear wheels fitted with pneumatic or puncture proof tyres and hand rims for user self propulsion The Meteor is painted in a choice of durable powder coated colour finishes Seating and backrest materials are flame retardant nylon 1 1 WHEELCHAIR TRANSPORTATION IN MOTOR VEHICLES All of the wheelchairs in our range are designed to be easily transported and most of them dismantle into manageable parts in seconds Consideration should be given to the type of vehicle in which the wheelchair may be carried A small car with a heavy power chair in the boot may be affected in the way in which it steers or brakes so care should be taken to distribute the load sensibly It should also be noted that even a lightweight manual wheelchair has considerable mass in the event of e
4. RANSFER FROM A WHEELCHAIR This can only be done comfortably to a seating position that is at the same level and to a seat that does not have side arms which may obstruct movement Flip up the footrest slide the footrest hanger locking pin and swing the footrest assembly to the side Place the side of the wheelchair up against the seat you want to sit on and apply the brakes If an assistant is available ask them to steady the wheelchair to prevent any movement that may take place You may find the use of a transfer board helpful Place one hand on the seat rail and place the other hand on the seat or surface that you are transferring to ensuring it is stable Move forwards in the wheelchair and leaning slightly forwards push upwards and slide sideways Z ot DLE IMPORTANT Care should be taken to ensure that the user can support their own body weight when transferring 15 13 USING YOUR WHEELCHAIR DO S AND DON TS Moving forward and backwards is achieved by grasping both handrims and rotating in the required direction Turning left and right is achieved by holding the wheel stationary in the direction of travel whilst rotating the opposite wheel in the forward motion Braking of the wheelchair can be achieved by gripping the handrims to slow rotation Be aware that high speeds may cause friction burns Gloves may be advisable DO obtain tr
5. RJ MOBILITY LTD METEOR USER MANUAL THE WHEELCHAIR THAT PROVIDES ACTIVE ADULT USER INDEPENDENCE Before using your wheelchair please read this manual as it contains important information for the assembly transportation and use of your wheelchair Thank you for choosing a Meteor lightweight active user wheelchair We hope that it will provide many enjoyable years of reliable service and fulfil all your mobility needs This user manual should be read carefully before you use your wheelchair This user manual contains important information regarding the safe operation and maintenance of your Meteor lightweight active user wheelchair Please make sure that you understand all the instructions thoroughly If you fail to understand anything or have any questions concerning operation and maintenance please contact your supplier who will provide you with expert professional advice R J Mobility Limited is a quality approved manufacturer to BS5750 Part 2 ISO 9002 This product is manufactured to comply with the essential requirements of the Medical Devices Directive 93 42 EEC In line with our policy of continuous improvement we welcome any suggestions that could lead to product improvement a 3 OMDNAAURAN CONTENTS INTRODUCTION USER CATEGORIES PARTS IDENTIFICATION UNFOLDING AND PREPARING FOR USE FOLDING FOR STORAGE OR TRAVEL PUSH HANDLES ATTENDANT PUSHING GETTING IN AND OUT OF YOUR WHEELCHAIR GETTING IN FRO
6. aining or assistance before attempting to kerb climb or descend DO ensure an attendant is present when balancing the wheelchair on its rear wheels until you are fully proficient in kerb ascending and descending DO ensure anti tip rollers are fitted correctly DO take care negotiating inclines uneven soft or slippery surfaces as the risk of tipping over is increased DO be aware of the surface temperature of all the wheelchair parts in hot and cold weather DO be aware that erratic control can cause injury to the user and other people DO be aware that effectiveness of the brakes may be reduced if the tyres are wet muddy or greasy DO observe the Highway Code DO avoid soft ground DO keep clothes rugs covers etc clear of the wheels DO fit a waist safety belt for additional security DO be aware that move pavements slope slightly towards the kerb and the wheelchair may tend to pull towards the road DO fit push handles when attendant pushing for prolonged periods of time DO use two hands for pushing DO ensure that the wheelchair is hygienically clean and suitable for multi user use if applicable DO NOT use the wheelchair without footrests as feet may become trapped underneath DO NOT use the wheelchair if the tyres are not inflated to the correct pressure as this may render the brakes ineffective DO NOT turn quickly as this may cause the wheelchair to tip DO NOT carry heavy objects passengers as this may lead to insta
7. bility DO NOT lift the wheelchair using the armrests or footrests always use the main frame DO NOT trap fingers between the brake pad and the tyre DO NOT use the wheelchair while under the influence of drugs or alcohol DO NOT force the wheelchair forward if it becomes stuck DO NOT stand on the footrests of the wheelchair under any circumstances 16 14 ASCENDING AND DESCENDING SLOPES SAFELY IMPORTANT Movement of the occupant could cause the wheelchair to tip on a slope SLOPE ANGLE MAXIMUM SLOPE ANGLE 1 IN 10 6 The Meteor wheelchair is designed with a short wheelbase in order to make it more manoeuvrable and so that it can be balanced by the user on its rear wheels This makes it more liable to tip back when ascending slopes The Meteor wheelchair remains stable when ascending a slope of 1 in 10 6 Beware if you feel the wheelchair becoming unstable do not proceed When descending a slow speed should be maintained by gripping the handrims firmly Excessive speed could cause friction burns on the hands On steep slopes care should be taken not to slip out of the wheelchair Wherever possible an attendant should provide assistance by pushing if ascending or restraining if descending whilst the occupant controls the wheels Attendants should have sufficient strength to control the wheelchair and occupant when negotiating inclines kerbs or steps 17 15 ASCENDING AND DESCENDING KERBS INDEPEN
8. d by lifting it upwards It should not be possible to remove the backrest if the levers have been located correctly Lift up the skirt guards ensuring that the rear flap A passes around the backrest tube and fasten the Velcro panels tog ether see FIG 4 Fit the footrest hangers by locating each footrest hanger A in to the wheelchair frame socket B and rotate the footrest hanger until it locks into the hole at position C The locking pin D will lock the footrest hanger into position see FIG 5 IMPORTANT Figure 5 B Keep fingers away from the frame socket to avoid trapping fingers Lower the footrest bar A into position and locate on the retaining pin B see FIG 6 Figure 6 B IMPORTANT Keep fingers away from the end of the footrest to prevent trapping fingers The Meteor footrest height is adjusted by releasing the footbar A from the retaining pin B and lifting it upwards Each footrest hanger can be adjusted for length by pressing both spring studs C and sliding the inner stems D to the required length see FIG 7 Figure 7 Anti tip rollers are fitted to inhibit backwards tip and can be adjusted to give a choice of two angles To adjust the angle press both spring studs A and reposition to the pre drilled holes in the tipping bar B see FIG 8 Figure 8 9 The rollers can be removed from operation by rotating the assembly upwards and locating the
9. e ability to co ordinate both arms and hands with sufficient strength to self propel and control the wheelchair safely and maintain an upright seating position A3 Occupant with sufficient upper body control who can maintain an upright seating position IMPORTANT The above identifies the minimum user characteristics suitable for the Meteor Lightweight Active User Wheelchair 3 WHEELCHAIR PARTS IDENTIFICATION FOR METEOR LIGHTWEIGHT ACTIVE USER ADULT WHEELCHAIR Once the packaging has been removed check for missing parts against the diagram below and inspect for damage to the more fragile parts such as handrims spokes seat and back upholstery and footrest assembly There should be nothing bent or broken REMOVABLE BACKREST 2 SKIRT GUARD 10 BACKREST LOCK LEVER 3 FOOTREST RELEASE LEVER 4 BRAKE LEVER 5 FOOTREST HEIGHT ADJUSTER 9 TIPPING LEVER 6 FLIP UP FOOTREST 8 ANTI TIP ee i 7 FRONT CASTOR Please contact your supplier immediately if the wheelchair is not to your satisfaction 4 UNFOLDING ASSEMBLING AND PREPARING THE METEOR WHEELCHAIR FOR USE It may be advisable to have the wheelchair prepared for use for the first time by an able bodied assistant Until the folding components have lost some of their stiffness the wheelchair may require moderate strength and effort to assemble it properly No tools are necessary for the assembly of your wheelchair and the procedure is as follows 1 W
10. e seat and bend slightly forward to bring the body weight to the front of the seat With both feet firmly on the ground and one foot back push into the upright position 11 SIDE TRANSFER TO A WHEELCHAIR This can only be done comfortably from a seating position that is at the same level and from a seat that does not have side arms which may obstruct movement Flip up the footrest slide the footrest hanger locking pins and swing the footrest assemblies to the side Place the side of the wheelchair up against the seat you are on and apply the brakes If an assistant is available ask them to steady the wheelchair to prevent any movement that may take place Beware of the wheel and skirt guard and the upholstery securing screws during the transfer process Sufficient support is needed so that you can clear these components as you transfer You may find the use of a transfer board helpful When you are ready reach out and place one hand on the seat as far away from you as you can reach and push downwards and sideways transferring your weight from your seat to the wheelchair Swing the footrest assemblies into position by rotating them to the front of the wheelchair Beware of catching your ankles or lower leg as you swing them into position Fold down the footrest and place your feet on it IMPORTANT Care should be taken to ensure that the user can support their own body weight when transferring 14 NOTE 12 SIDE T
11. each side to point upwards and lift the back rest upwards until it becomes detached from the wheelchair see FIG 2 Figure 2 Standing to the side of the wheelchair place each hand under the front and back of the seat fabric Lift upwards sharply to ensure the wheelchair fully folds see FIG 3 To remove the wheels ensure the brake are not applied With one hand hold the frame of the wheelchair and with the other hand hold the spokes surrounding the hub and fully depress the centre button Pull the wheel away from the wheelchair and axle bush and release the centre button see FIG 4 Figure 4 10 6 PUSH HANDLES As an active user wheelchair the Meteor is designed so that the user has a high degree of independence Push handles are therefore not supplied as a standard feature However where a reasonable level of attendant control is required push handles are available as an optional accessory from your wheelchair supplier To fit the push handles remove the end caps A from the backrest assembly B and insert the push handles C into the backrest assembly Pass the set screw D through the backrest assembly and push handle Attach the nut E and tighten until it is a snug fit against the backrest assembly see FIG 1 To remove the push handles reverse the above procedures Figure 1 11 7 ATTENDANT PUSHING IMPORTANT It should be noted that the combined weight of the whee
12. eviously described 4 Pull the tilted wheelchair up the kerb and on to the pavement The wheelchair user may wish to self propel to assist the attendant 5 Continue pulling until the castors are over the pavement Gently lower the castors to the ground YS LLLLILALLLLILALLLLLLL ALLL NOLL LLL LLL LLL Lh 20 GOING DOWN A KERB BACKWARDS WITH AN ATTENDANT This is the easiest and smoothest method and is the reverse sequence to that described in GOING UP A KERB FORWARDS As it requires the attendant to step off the kerb backwards into the road exercise extreme caution 1 2 Back the wheelchair to the edge of the kerb Ensure that the anti tip rollers are correctly positioned see Section 4 FIG 7 Use the push bar to pull the rear wheels down onto the road Tilt the wheelchair backwards as previously described and push the tilted wheelchair further into the road The user may wish to restrain the handrim to assist the attendant When the footrests are clear of the kerb lower the front castors on to the road 21 GOING DOWN A KERB FORWARDS WITH AN ATTENDANT This method has the advantage that you can see the traffic more easily The disadvantages are that it is harder physical work and it is not easy to lower the wheelchair gently without jarring the person in the wheelchair 1 Position the wheelchair so that the front castors are close to the edge of the kerb and check that the road is clear Ensure that the a
13. heel Removal and Refitting In order to release the side skirts remove the quick release wheels and re fit them Lift the frame with one hand and the wheel with the other hand Hold the spokes surrounding the hub and fully depress the centre button Pull the wheel from the axle bush and release the centre button You can now lift up the side skirts To refit the wheel press the centre button in and insert the axle fully into the axle bush and release the centre button see FIG 1 Figure 1 PRESS IMPORTANT Always ensure that the wheel is fully locked Pull the wheel outwards without depressing the centre button If located correctly the wheel will not come off 2 Apply the brake by pushing lever A forward see FIG 2 Stand at one side of the folded Meteor Tilt it slightly to balance on one rear wheel and simultaneously press down on the opposite side of the seat and push until the wheelchair is fully open Check that the seat tubes A have located into their cradles B see FIG 3 IMPORTANT Figure 3 Ensure that your fingers are kept above the level of the seat to avoid trapping them between the seat tube and the wheelchair frame Fit the backrest by rotating the lever B at each side of the wheelchair to point upwards and slide the backrest fully into position rotate the two levers B to point downwards thus locking the backrest see FIG 4 Check that the backrest is securely fitte
14. ing increased back support Frame Colour Choice To meet customer requirements a wide choice of colours is available in a durable powder coated finish Seat Height Width Depth Variation To ensure that our product meets all ergonomic needs significant variations to standard are available as made to order variants Reinforced Upholstery Increases weight carrying capacity when associated with other modifications Choice of Upholstery A range of coloured upholstery is available to meet our customers requirements Armrest Assemblies Of tubular construction fitted with foam flame retardant pads these offer a high degree of comfort for the wheelchair user Puncture Proof Tyres An invaluable option for those people who cannot afford the risk and cost associated with punctures JDG 24 METEOR WHEELCHAIR ACCESSORIES Cushions A choice of colour co ordinated backrest and seat cushions is available in either flat or contoured shapes They enhance the wheelchair s appearance as well as offering a high degree of comfort Waist Belt A safety belt fitted with quick release fastener offering user and attendant peace of mind Calf Strap Offers support to the calf for users with impaired leg control Lightweight Carry Bag A useful accessory when travelling this bag ensures that all the wheelchair components remain together without fear of loss Crutch Walking Stick Holder Positioned at the rear of the wheelchair this option enables
15. ion 15 12 8 GETTING IN AND OUT OF YOUR WHEELCHAIR IMPORTANT Do not stand on the footrest Do not lean on one armrest only if fitted Do take extra care on slippery uneven surfaces and slopes Do remove any unnecessary obstructions Do apply the brakes Do fit the backrest as this prevents the wheelchair from folding There is a risk of the wheelchair tipping if you are too far forward on the seat If you have not attempted these movements before or your medical condition does not allow you to support your body weight comfortably it is advised that an able bodied person be in attendance to help and assist 9 GETTING IN THE WHEELCHAIR FROM THE FRONT Apply the brakes Flip up the footrest and slide the footrest hanger locking pins and rotate the footrest assemblies to the side Stand close to the front edge of the seat with your back to the wheelchair and lower yourself into the wheelchair Swing the footrest assemblies back to the front lower the footrest and place your feet on it Beware of catching your ankles or lower legs as you swing the footrests into position IMPORTANT Do not drop your body weight into the wheelchair as this could cause it to tip backwards 13 NOTE 10 GETTING OUT OF YOUR WHEELCHAIR FROM THE FRONT TO A STANDING POSITION Apply the brakes Flip up the footrest and slide the footrest hanger locking pins and rotate the footrest assemblies to the side Move forward on th
16. lchair and user can be quite considerable so take great care when tipping backwards As an active user wheelchair for those requiring a high degree of manoeuvrability and independence the Meteor is not intended for those users requiring a high degree of attendant control Where occasional attendant pushing is provided the following notes apply Attendants assistants will require enough physical strength and agility to safely assist the user when getting in and out of the wheelchair Where possible adequate space should be allowed as physical exertion in confined spaces can lead to strains and injury to both the user and attendant Attendants in control should be mentally mature and responsible The wheelchair occupant should be made comfortable by the attendant who should a Not walk too quickly when pushing the wheelchair b Make all moves slow and deliberate informing the occupant when he or she intends changing direction preferably before the manoeuvre is commenced Tipping the wheelchair or changing speed can cause occupant distress C Pay attention to the road surface avoiding uneven or soft ground d When at a halt ensure that the occupant can see and communicate To assist the attendant push handles are available as an optional accessory For fitting instructions see Section 6 It is safer to avoid kerbs wherever possible and use ramped kerbs or slopes If this cannot be avoided then adopt the procedures in Sect
17. lchair in constant daily use Open the wheelchair All movements should be free throughout the folding range and should not bind or seize whilst operating All pivot bolts should be secure with no sign of nuts or bolts working loose but they must be free enough to allow the component parts to move whilst operating Examine the seat and backrest upholstery for wear or damage Examine the retaining screws for tightness Any that are protruding or loose should be tightened with a Pozidrive cross point screwdriver Examine the brakes for wear damage or misalignment Ensure that both brakes prevent the rear wheels turning when fully applied and the tyres are inflated to the correct pressure If not refer to your wheelchair supplier for adjustment Check the castors for free rotation of the castor wheel and swivel assembly Look for looseness or binding Check the rear wheels for free and easy rotation Check the rims for any buckling or distortion and check for any spokes that may be loose or need tightening Check that the quick release wheels remove and refit securely and that the plunger mechanism operates smoothly without sticking Check the push handles for security and the handgrips for wear or damage and that they are securely attached to the push handles Examine the footrest hangers for effective locking when fully forward 25 23 METEOR FACTORY FITTED OPTIONS Backrest Extension Choice An upholstered extension offer
18. lers and operators of restraint systems should be trained in their correct use by the restraint manufacturer or approved specialist Additional fittings such as trays should be removed and stowed separately It is recommended that wheelchairs with a full height backrest are used R J Mobility have undertaken crash testing to latest known international standard test methods and recommend the use of the Unwin 4 Point Tie Down system The following wheelchairs have been tested and we have published details which are available upon request Barrett 7H Barrett 10H Meteor additional back support is recommended Mini Meteor Maxi Independent Other products in our range and R J Mobility products manufactured prior to testing have been used to transport users in motor vehicles over many years without serious incident and it must be decided by the user carer whether to continue to do so It is not as safe as travelling in a vehicle seat and there are risks involved These are minimised with the use of effective recommended equipment restraints and our company believes in freedom of choice for informed individuals so please be aware of the risks and make your own informed choice To obtain free written details of the tests we have carried out please write to RJ Mobility Limited Boy Lane Wheatley Halifax HX3 5AF England 2 USER CATEGORY FOR THE METEOR LIGHTWEIGHT ACTIVE USER WHEELCHAIR A1 Occupant with all limbs intact and having th
19. mergency braking and some form of restraint is essential when transporting any wheelchair in any vehicle It is strongly recommended that the user transfers to a vehicle seat and the wheelchair is transported separately However if this is not possible and the user intends to travel ina moving vehicle whilst seated in the wheelchair it is essential they follow clear safety guidelines and understand that this is not as safe as using the vehicle seat Many of our wheelchairs have been shown to withstand simulated crash conditions without injury to the user We have compiled a separate document describing the conditions in which these tests were carried out and clearly detailing the manner in which the wheelchair should be restrained Any wheelchair restraints must be separate to the user restraints It is the responsibility of the transport operator and the wheelchair user to ensure that safety measures taken are suitable for both the wheelchair user and other passengers All passengers in motor vehicles accept that risk is involved in travel but this is compounded by wheelchair use The wheelchair brakes are not designed to withstand forces such as cornering acceleration and braking within a motor vehicle therefore additional special restraints must be provided The wheelchair should be secured to the vehicle floor in line with the direction of travel The occupant should be separately restrained to the vehicle and NOT to the wheelchair Instal
20. nti tip rollers are correctly positioned see Section 4 FIG 7 Pull back on the push bar gripping it firmly and at the same time push downwards and forwards with the foot on the tipping lever to balance the wheelchair on its back wheels The person in the wheelchair may be able to help by using the handrims to steady the wheelchair Move the wheelchair forwards and then gently lower the rear wheels down the kerb while supporting some of the wheelchair s weight yourself Make sure that both wheels touch the ground at the same time because if not the wheelchair could tip over sideways Gently lower the front castors Check that the road is still clear before moving off IMPORTANT Never tip the wheelchair forwards when going down a kerb The person in the wheelchair might fall out 16 UNEVEN SLIPPERY AND SOFT SURFACES Care should be taken at all times Maintain a slow speed so that you can keep control Note that grass may be soft and the wheels may sink causing the wheelchair to tip Any moisture or mud on the tyres may affect the proper operation of the parking brakes 22 17 CARE AND MAINTENANCE OF YOUR METEOR WHEELCHAIR Your Meteor wheelchair should require very little maintenance when used with care and discretion and will retain its appearance if looked after and cleaned in accordance with the following instructions Protection of your wheelchair during shipment or travel is dependent upon the type of journey e
21. nvisaged but attention should be given to protecting the more fragile items 18 TYRE PRESSURE IMPORTANT Under no circumstances should garage powered airlines be used If your wheelchair is fitted with pneumatic tyres a hand pump is provided Tyres are best inflated by an assistant with a car type foot pump up to the recommended pressure of 50psi 340 Kilopascals KPA This pressure is also displayed on the wall of the tyre Pressures should be checked weekly using a proprietary pressure gauge and a daily visual check made of the tyre condition Things to look for are nails sharp objects etc stuck in the tyre tread splits cracks or abrasions to the tyre wall and a deflated tyre this would indicate a puncture or leaking valve Excessively worn or damaged tyres should be replaced without delay If the tyre does become deflated or need replacing contact your wheelchair supplier for assistance IMPORTANT Brakes may not work if tyres are under inflated 19 CLEANING The upholstery may be cleaned with warm water and mild soap Never use a solvent of any type to clean your wheelchair The paintwork may be cleaned or polished with a car type polish Wipe off any moisture after outdoor use and store your wheelchair in cool and dry conditions 23 20 LUBRICATION The castors on your wheelchair do not need any additional lubrication Each week a few drops of general purpose oil should be added to frame folding pivo
22. ork carried out Repairer s stamp 6 Months Date Initial Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial 29 26 WARRANTY In the unlikely event of your needing it R J Mobility Limited s warranty is 1 Defective parts and items of faulty workmanship will be replaced or repaired free of charge for the first 12 months following delivery 24 months in the case of the crossbrace and frame 2 This warranty does not apply to fair wear and tear or where deterioration results from neglect carelessness accident misuse unauthorised modification or the fitting of parts not supplied by R J Mobility Limited Please contact the supplier of your wheelchair to arrange warranty repairs This does not affect your statutory rights 30
23. t points and brake pivots Wipe away any excess oil to prevent dirt collection It is essential that the quick release axle and bush are kept lightly lubricated at all times to ensure ease of action It is recommended that a silicon based lubricant is used for this application or a water displacing lubricant eg WD40 21 MAINTENANCE SCHEDULE IMPORTANT It is advisable that professional servicing is carried out at six monthly intervals for a wheelchair in constant daily use For a wheelchair exposed to less usage the weekly checks should be carried out every time the wheelchair is used DAILY CHECK Handrim damage and security Hand grips for secure attachment Brake operation Folding mechanism Loose or bent spokes WEEKLY CHECK Quick release wheel plunger mechanism operates smoothly without sticking Quick release wheel and castor security Seat and backrest upholstery cushions for tears or damage Push handles for security Cross brace folding mechanism Check that the pivot bolts are not loose Tyre pressure and condition Lubrication as above Section 20 24 22 GENERAL CHECKS TO BE CARRIED OUT AT MONTHLY INTERVALS IMPORTANT If any of the items listed below give cause for concern consult your wheelchair supplier immediately Do not overtighten upholstery screws as this can damage the upholstery It is advisable that professional servicing is carried out at six monthly intervals for a whee
24. ure the occupant s feet are on the footplates and will not slip off Release both brakes Place both hands firmly on the push handles Make sure the handgrips are secure and cannot be pulled off Ensure that the anti tip rollers are correctly positioned see Section 4 FIG 8 and put one foot on the tipping lever at the back of the wheelchair see diagrams below Tell the wheelchair occupant you are about to tilt backwards Pull back with both hands and push down and forwards with the foot This will bring the wheelchair onto the back wheels If it is tilted too far back it will be heavy to hold and the person in the wheelchair will feel unsafe Do not let the castors rise more than 4 10cm off the ground Push the wheelchair forwards The user can assist the attendant by propelling the rear wheels Gently lower the front castors on to the pavement and push the back wheels upwards over the kerb 19 GOING UP A KERB BACKWARDS WITH AN ATTENDANT IMPORTANT This is a difficult method requiring more strength and should only be attempted with a light person in the wheelchair 1 Turn the wheelchair around so that the back wheels are resting against the kerb 2 Ensure that the anti tip rollers are correctly positioned see Section 4 FIG 8 3 Pull back on the push bar and push downwards to tilt the wheelchair so that the front castors are off the ground The proximity of the kerb will prevent the use of the tipping levers as pr
25. walking sticks and crutches to be carried conveniently Push Handles Enables the attendant to push the wheelchair more easily A choice of height alternatives is available 27 25 SERVICE HISTORY As it is important to keep a documented record of service and repairs to your wheelchair this section of your manual should be completed by your wheelchair supplier with details of any work carried out This information will also be helpful to your supplier and to you should you decide to sell or exchange your wheelchair Please ensure that this manual accompanies your wheelchair whenever a service is required recommended every 6 months or any work is carried out Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial 28 Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial Service Interval Details of work carried out Repairer s stamp 6 Months Date Initial Service Interval Details of w
Download Pdf Manuals
Related Search