groLEDs - Jameco Electronics
Contents
1. LOOK AT THE PICTURE FOR THIS STEP CAREFULLY All 50 resistors are mounted on the back side of the printed circuit board All 50 resistors are mounted vertically with the body of the resistor residing over the larger round pad as shown and the flying lead in parallel with the body of the resistor being installed in the smaller octagonal pad as shown All 50 LEDs 3 colors in 2 different sizes are mounted on the top side of the printed circuit board the side with the white silkscreen print on it All 50 LEDs are installed identically with the anode lead the longer of the two leads being installed in the round hole and the cathode lead the shorter of the two leads AND the lead closest to the flat spot on the body of the LED being installed in the square hole For each resistor and LED pair of components the resistor is installed and soldered PRIOR to the LED s installation and soldering in order to ensure that the hot soldering iron does NOT melt the lens body of the LED ASSEMBLY GENERAL ORDER NOTE Task a a resistor row or group in a row is installed on the back side of the board bending the leads on the top side for retention Task b the leads for all of the resistors installed in task a above are soldered and trimmed Task c the leads of a LED row or group in a row is installed on the top side of the board bending the leads on the back side for retention Task d the leads for all the LEDs insta2. 1 800 831 4242 www Jameco com groLEDs Computer Controllable Adjustable Broad Spectrum High Brightness grow 50 LEDs lamp Kit PART NO 2259817 The groLEDs kit offers an economical versatile safe efficient and easy to use alternative to traditional and commercial grade Grow Lamp Light products BRIGHT The three different colors of LEDs all include high luminosity intensity ratings measured in candelas cd instead of normal LED millicandela mcd ratings The blue LEDs emit 57cd 57 000mcd the white LEDs emit 80cd 80 000mcd and the red LEDs emit 80cd 80 000mcd when they are powered at their nominal operating voltage The equivalent light output is that of very bright 217 standard candles when all LEDs are lit When the kit is for sale the Web Page will include an additional document the User s Manual which includes performance data listing lux and footcandle values for various combinations of LEDs red white and blue at different voltage levels The groLEDs lit photographs picture with this overview were all taken at the lowest light levels possible very low input voltages to prevent the blinding of the camera ADJUSTABLE SPECTRUM Unlike many full spectrum grow light products which attempt to provide some additional red and blue light energy mixed with the standard yellow white the groLEDs kit is designed to enable the user to specifically select the light color output based upon growing n
3. maintain their flat on the board BEFORE SOLDERING ensure that the flat edge of the body of all 5 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the red highlighted locations in the assembly drawing in the picture for this step all OK then position on the top side of the board Turn the board over and solder both leads of each LED at all 5 locations gt gt gt SAFETY NOTE E r Install Red LEDs JameCo 2095171 at five places LED44 LED41 R48 left of center LED50 and LED49 right of center iro Sou co Cumcolfcon fom co Onji 5 7 6 om colon oo oo co on co oo oo om co oo o oO Step 16 Assembly instructions for the last 5 White LEDs LOOK AT THE PICTURE FOR THIS STEP CAREFULLY The dashed blue and red boxes mostly in the center of the assembly drawing in the picture for this step shows where previously installed red white and blue LEDs are already on the board before starting this step Find the smaller 3mm T 1 size White LEDs they each have a diffused clear lens JAMECO 2174881 and remove the last 5 of them from their packaging Remember when installing the LEDs the long lead goes in the round pad hole Anode and the shorter lead goes in the square pad hole Cathode NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALITY At each of the 5 locations highlighted in a smaller red o
4. gt SAFETY NOTE BLUS rol Install Blue LEDs JameCo 2193889 at four places LED19 LED14 eft of center LEDS and LED18 right of center oc Qa GQ CS ob Ico Gato so o oo ogn Sn ige SH colon o lon 6nloo on co colon co 0n calzo SCMIico colon co jou onee og onog coo 5E oni e a p a o0 om coo oo oco orn co om oo om oo orn oo om oo co icgs Sool o og log 4 5E 2s ono Lo eno 2b cco om oo om O o Step 15 Assembly instructions for the last 5 Red LEDs mm LOOK AT THE PICTURE FOR THIS STEP CAREFULLY The dashed blue boxes mostly in the center of the assembly drawing in the picture for this step shows where previously installed LEDs of all three colors are already on the board before starting this step Find the 5mm T 1 3 4 size Red LEDs they each have a clear lens JAMECO 2203813 and remove the last 5 of them from their packaging Remember when installing the LEDs the long lead goes in the round hole Anode and the shorter lead goes in the square pad hole Cathode NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALITY At each of the 5 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs
5. in blue on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs maintain their flat on the board position on the top side of the board BEFORE SOLDERING ensure that the flat edge of the body of all 14 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the blue highlighted locations in the assembly drawing in the picture for this step If they are all OK then Turn the board over and solder both leads of each LED at all 14 locations Install Blue LEDs JameCo 2193889 at fourteen places LEDs 21 20 13 10 7 6 5 eft of center and LEDs 3 8 1 11 2 24 12 right of center gt gt gt SAFETY NOTE Seto 22D IEF ty 2 _ Ey LF 9 DOEDE OGG DGGE SSS Step 19 Assembly instructions Some Final Notes TASK Turn off your soldering iron you are finished for now mm LOOK AT THE PICTURE FOR THIS STEP The bottom left corner of the picture for this step shows what the bottom edge of the back side of the board assembly looks like if all four optional components are installed Their installation and operation is discussed in the User s Manual ABOUT THE USER s MANUAL A separate document also down loadable from the Jameco web site includes the following topics 1 Assembly installat
6. in detail in steps 2 and 3 SPECIAL NOTE Two resistors R3 amp R21 are rotated from normal At each of the 14 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the resistor body over the large hole from the backside of the PC board bending the leads on the top side of the board to retain them in place while ensuring that the resistors maintain their vertical orientation on the backside of the board Turn the board over and solder both leads of each resistor at all 14 locations gt gt gt SAFETY NOTE fol Install 56Q JameCo 690566 at 14 places R21 R20 R13 R10 R7 R6 R5 right of center R3 R8 R1 R11 R2 R24 and R12 left of center note rotations Step 18 Assembly instructions for the last 14 Blue LEDs LOOK AT THE PICTURE FOR THIS STEP CAREFULLY The dashed blue box in the center of the assembly drawing in the picture for this step shows where previously installed blue red and white LEDs are already on the board before starting this step Find the 5mm T 1 3 4 size Blue LEDs they each have a clear lens JAMECO 2193889 and remove 14 of them from their packaging Remember when installing the LEDs the long lead goes in the round hole Anode and the shorter lead goes in the square pad hole Cathode NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALITY At each of the 14 locations highlighted
7. 0566 Resistor Carbon Film 56 Ohm 1 4 Watt 5 Bag of 10 Step 1 General Introduction In just 5 072 of Printed Circuit Board area up to 104 thru hole components will be installed 50 LEDs in 3 colors in 2 different sizes will be installed on the top side Shown at bottom center of picture for this step and 50 resistors in 2 values in 1 size will be mounted vertically on the back side with optionally 3 power switches and 1 connector ABOUT THIS DOCUMENT This particular document ONLY presents a brief INTRO introduction to the groLEDs kit followed by ONLY the ASSY assembly instructions for building the kit The Separate User s Manual contains more information ABOUT THE USER s MANUAL A separate document also down loadable from the Jameco web site includes the following topics 1 Assembly installation of the optional components 2 Control Connections for manual or automatic operations or both 3 How to wire multiple groLEDs kits to a single tower computer power supply 4 PERFORMANCE data including a light level outputs in Lux for b light level output in Foot Candles for c input power current levels for d for seven different color combinations e all with varying input voltage levels 3 0V to 5 5V 5 Technical Drawings including a annotated schematic b Printed Circuit Board black white photoplot Top Copper layer c Printed Circuit board black white photoplot Bottom Copper Layer d Assem
8. 37 R38 R34 R18 left of center R19 R32 R40 an R14 right of center E sF ter thivstep 14 lete Step 14 Assembly instructions for the next 4 Blue LEDs LOOK AT THE PICTURE FOR THIS STEP CAREFULLY The dashed blue box in the center of the assembly drawing in the picture for this step shows where previously installed blue red and white LEDs are already on the board before starting this step Find the 5mm T 1 3 4 size Blue LEDs they each have a clear lens JAMECO 2193889 and remove 4 of them from their packaging Remember when installing the LEDs the long lead goes in the round hole Anode and the shorter lead goes in the square pad hole Cathode NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALITY At each of the 4 locations highlighted in blue on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs maintain their flat on the board position on the top side of the board BEFORE SOLDERING ensure that the flat edge of the body of all 4 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the blue highlighted locations in the assembly drawing in the picture for this step If they are all OK then Turn the board over and solder both leads of each LED at all 4 locations gt gt
9. 66 and remove 9 of them from their packaging Bend one of the leads down alongside the body of the resistor for each of the 9 resistors as shown in the picture for this step and as shown in detail in steps 2 and 3 At each of the 9 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the resistor body over the large hole from the backside of the PC board bending the leads on the top side of the board to retain them in place while ensuring that the resistors maintain their vertical orientation on the backside of the board Turn the board over and solder both leads of each resistor at all 9 locations gt gt gt SAFETY NOTE Install 5602 JameCo 690566 at nine places R4 R36 R35 R17 left of center R27 R39 R33 R31 and R15 right of center Step 9 Assembly instructions for the next 4 Blue LEDs LOOK AT THE PICTURE FOR THIS STEP CAREFULLY The dashed blue box in the center of the assembly drawing in the picture for this step shows where previously installed blue LEDs are already on the board before starting this step Find the 5mm T 1 3 4 size Blue LEDs they each have a clear lens JAMECO 2193889 and remove 4 of them from their packaging Remember when installing the LEDs the long lead goes in the round hole Anode and the shorter lead goes in the square pad hole Cathode NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALIT
10. Icoon oo b KOS A a 5O 6n soleno ce on p om co cB o01 q oo ree 6 So 6n colon 6 6n om toms coloni om BLUS cof unAt lt gt lt gt ee 6 yy Step 11 Assembly instructions for the first 5 White LEDs mm LOOK AT THE PICTURE FOR THIS STEP CAREFULLY The dashed blue and red boxes mostly in the center of the assembly drawing in the picture for this step shows where previously installed blue and red LEDs are already on the board before starting this step Find the smaller 3mm T 1 size White LEDs they each have a diffused clear lens JAMECO 2174881 and remove 5 of them from their packaging Remember when installing the LEDs the long lead goes in the round pad hole Anode and the shorter lead goes in the square pad hole Cathode NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALITY At each of the 5 locations highlighted in a smaller red blue LED body symbol on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs maintain their flat on the board position on the top side of the board BEFORE SOLDERING ensure that the flat edge of the body of all 5 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the highlighted locations in the assembly drawing in the picture for
11. Y At each of the 4 locations highlighted in blue on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs maintain their flat on the board position on the top side of the board BEFORE SOLDERING ensure that the flat edge of the body of all 4 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the blue highlighted locations in the assembly drawing in the picture for this step If they are all OK then Turn the board over and solder both leads of each LED at all 4 locations Install Blue LEDs JameCo 2193889 at four places LED27 LED15 eft of center LED4 and LED17 right of center gt gt gt SAFETY NOTE o 29 Pf Foo obn colonjyc coms on co lco co Sn co 6N co 6nIicO on so 6n so on colom co n SO of cO Col go 20 om co 6 colon co OR so n coIlCHlce on so 6n co CHICO pn co 6R SO OB cOIGO co CH 20 Om co ff1 0 00 co OA cO CF coloom cOo on co om co conlco on co on 5O Go colonise Co sO om d co aon BLUS Se OD WHT PEO O Step 10 Assembly instructions for the first 5 Red LEDs mm LOOK AT THE PICTURE FOR THIS STEP CAREFULLY The dashed blue boxes mostly in the center of the assembly drawing in the picture for this step shows where previously installed blue LEDs are already
12. atively high heat conditions are prone to fail long before the actual light emitting diodes themselves The groLEDs kit uses only passive components making it much more dependable for many years of service Unlike most Christmas LED strings if and when a LED fails on the groLEDs kit all the other LEDs remain lit without changing their intensities ADJUSTABLE BRIGHTNESS Since the groLEDs kit is completely passive it is possible for the user to vary the light intensity as needed by varying the 5V input down to 3 0V up to about 5 5V to decrease or increase the brightness level as needed for specific growing requirements Details about these voltage levels and the overall power requirements are included in the User Manual for this kit THRU HOLE ONLY The small 1 95 x 2 6 2 layer printed circuit board uses thru hole components only making it a kit that can be built by any level of expertise All 50 LEDs are mounted on one side of the board see the picture with this overview and all of the other componenis including optional ones are mounted on the backside of the board Since this is not a typical assembly process to include thru hole components on both sides of a printed circuit board the instructions walk the kit builder through the process to ensure reliable solder connections and no scorched LEDs or fingers There are four 0 2 diameter holes in each of the corners of the groLEDs kit assembly for mounting or hanging the fixtur
13. bly Drawings for both the top and the bottom of the board e Printed Circuit Board Statistics size of board number and sizes of holes trace space dimensions etc The groLEDs kit overview discuses not repeated here important features and functions including Adjustable Brightness Adjustable Spectrum Directional Light Focus Ease of Control Safety Low Cost and Reliability to name a few THRU HOLE ONLY The small 1 95 x 2 6 2 layer printed circuit board uses thru hole components only making it a kit that can be built by any level of expertise All 50 LEDs are mounted on one side of the board see the picture with this step and all of the other components including optional ones are mounted on the backside of the board Since this is not a typical assembly process to include thru hole components on both sides of a printed circuit board the instructions steps that follow walk the kit builder through the process to ensure reliable solder connections and no scorched LEDs or fingers There are four 0 2 diameter holes in each of the corners of the groLEDs kit assembly for mounting or hanging the fixture for usage GENERAL ASSEMBLY FLOW Moving from the center of the board outwards resistors will be installed on the backside before their corresponding LEDs will be installed on the top side of the board to ensure that the hot soldering iron does not melt the temperature sensitive dome lenses of the LEDs More details are provided i
14. e ALL facing the right edge as shown in the picture for this step m IT IS VERY IMPORTANT TO GET THE RIGHT LEDs MOUNTED IN THE RIGHT HOLES Each of the assembly steps that follow that are involved with installing LEDs will include a highlighted assembly view diagram showing exactly where the LEDs are to be installed per step One other note All 50 LEDs have a clear lens so they do NOT look like the picture associated with this step when they are not lit As a matter of fact the Red and Blue LEDs look identical when not lit so be careful not to mix them up during your assembly work te TURN ON YOUR SOLDERING IRON Step 5 Assembly instructions for the first 8 resistors LOOK AT THE PICTURE FOR THIS STEP CAREFULLY Find the 56o0hms resistors JAMECO 690566 and remove 8 of them from their packaging Bend one of the leads down alongside the body of the resistor for each of the 8 resistors as shown in the picture for this step and as shown in detail in steps 2 and 3 At each of the 8 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the resistor body over the large hole from the backside of the PC board bending the leads on the top side of the board to retain them in place while ensuring that the resistors maintain their vertical orientation on the backside of the board Turn the board over and solder both leads of each resistor at all 8 l
15. e for usage WHY My wife and live in the woods where consistent growing sun light is unheard of making it difficult to start new plants and even to keep mature plants growing properly during the winter We have tried many artificial light sources all of them with various short comings most of them extremely expensive Necessity is the Mother of Invention hope that you enjoy the fruits of this labor WARNING If you are unsure of the dangers involved with your particular project consult with someone who is experienced Always wear eye protection and gloves FAILURE TO INITIATE AND FOLLOW YOUR OWN SAFETY PROCEDURES MAY RESULT IN BODILY INJURY OR DEATH Time Required 3 4 hours depending upon depending on experience Experience Level Beginner Required tools and parts e Soldering iron and solder e Wire cutters e Needle nose pliers OPTIONAL COMPONENTS details later 1 5Vdc 2Amp power supply see User Manual for more details and options 2 3 SPDT Slide Switches Jameco 109171 for on board on off switches on the backside 3 2 position Terminal Block Jameco TBD for on board wire to board terminal block connection on the backside Bill of Materials Jameco SKU Component Name 2193889 T1 3 4 5mm Clear Lens Blue LED 1900mcd 468nm 2174881 3mm 8000mcd White LED with Diffused Lens 2203813 LED Ultra Red Water Clear T1 3 4 8000mcd 635Nm 1 7Vf 20 View Angle 690620 Resistor Carbon Film 100 Ohm 1 4 Watt 5 In Bags of 10 69
16. eeds The color combinations include 1 OFF emulating night time darkness 2 BLUE Only ON or 3 RED Only ON or 4 WHITE Only ON or 5 BLUE and RED Only ON or 6 BLUE and WHITE Only ON or 7 RED and WHITE Only ON or 8 BLUE and RED and WHITE all ON This enables the user to emphasize the blue end of the spectrum when attempting to promote healthy vegetation growth while the red end is used when enhancing the budding and flowering phases of growth depending upon specific growth requirements DIRECTIONALLY FOCUSED Common grow lamps in the shape of T5 Florescent Tubes or common incandescent shaped bulbs broadcast their light in almost all directions requiring mirror reflectors to aim the light where it is needed by the plants LED Lamps with narrow beam widths aim their light like spot lights right where it is needed by the plants EASILY CONTROLLED Most grow lamps including many hi tech LED lamp fixtures only provide on off capability The groLEDs kit is designed so that each bank of colors blue white and red can be individually controlled manually or automatically via computer controlled relay contacts or both This enables the user to control the spectrum and the time that light is on versus off changing as the growing cycles change on a per plant basis if desired POWER SAFE Mixing water and 115VAC never seemed like a good idea in any kind of growing environment Nearly every grow light available includin
17. g most LED grow lamps are powered by 115VAC whether by a power cord that plugs into a nearby socket or one that screws into a lamp socket wired for 115VAC The groLEDs kit is designed to be run from 5VDC enabling the user to safely use water near the groLEDs kit fixture without fear of electrocution The user places the 5V power supply in a safe dry location remote from the growing watering area Again the User Manual will list the light output values and the operating current levels for a broad range of operating voltages from about 3 0V up to over 5 5V INEXPENSIVE Compared to all other grow light solutions the groLEDs kit is very inexpensive Not including the printed circuit board and optional components the Jameco catalog list price for all 50 LEDs and their current limiters is just 21 45 Many groLEDs kits can be powered from a single extremely inexpensive 15 00 common Computer tower power supply Because these power supplies source high current levels for both 3 3V and 5 0V relay control of light levels and colors is very simple to implement RELIABLE LEDs have a life cycle measured in tens of thousands of hours or many years significantly longer than any other grow light solution Many commercially available 115VAC powered LED Grow bulbs include integrated AC to DC converters to create the proper power parameters for powering the LEDs within the bulb fixture These converters being active electronics subjected to rel
18. ide of the board and 2 1000hms located at just 10 positions on the backside of the board m IT IS VERY IMPORTANT TO GET THE RIGHT RESISTORS MOUNTED IN THE RIGHT HOLES Each of the ASSY assembly steps that follow involved with installing resistors will depict a similar assembly diagram as shown for this step highlighting the correct locations for the resistors assembly for that given step REMEMBER to install the resistor s body lead into the larger of the two pads with the flying lead in the smaller one 40 resistors all 56 2 in value are mounted at locations Ri gt R40 like R3 shown in the left corner in this view Side View of R3 Miounted WVertically off of the back of the Printed Circuit Board Step 4 Introduction to the LEDs and their locations The printed circuit board for the groLEDs kit uses two unique shapes and sizes of solder hole pads for assisting the kit builder in properly installing the 3 different colors in 2 different sizes of LEDs LOOK AT THE PICTURE FOR THIS STEP CAREFULLY All 50 LEDs are installed identically with the anode lead the longer of the two leads being installed in the round hole and the cathode lead the shorter of the two leads AND the lead closest to the flat spot on the body of the LED being installed in the square hole All 50 LEDs are oriented in the same direction so that the flat side of the body of the LED indicating the Cathode Lead ar
19. ion of the optional components 2 Control Connections for manual or automatic operations or both 3 How to wire multiple groLEDs kits to a single tower computer power supply 4 PERFORMANCE data including a light level outputs in Lux for b light level output in Foot Candles for c input power current levels for d for seven different color combinations e all with varying input voltage levels 3 0V to 5 5V 5 Technical Drawings including a annotated schematic b Printed Circuit Board black white photoplot Top Copper layer c Printed Circuit board black white photoplot Bottom Copper Layer d Assembly Drawings for both the top and the bottom of the board e Printed Circuit Board Statistics size of board number and sizes of holes trace space dimensions etc Now go GROW with your new groLEDs kit assembly Ao f 2 j 9 ol Cis wv ie 16 9666 5 080 5 Me ZS k 9999 opis vy d YAA w wW WIGAN 6QH d Ead A a o ANg AA hg Ms Kj G 4 7 f te o e y D S o E NOE 1 sa A Q 2 Sas Vila aN details about installing optional componen see left how to apply and control power and other useful information eer
20. lled in task c above are soldered and trimmed Then the next rows are installed from the center row outward until all 100 components 50 resistors and 50 LEDs are installed 50 Resistors all Mounted Vertically onthe ide of the PC Board with the resistor body mounted over the larger round hole and the flying lead installed inthe smaller octagonal hole Installed on lt 1 Back lt side of PC Board ontop gt side of gt Board Sob co 6 k 50 LEDs all Mounted on the top side 4 Installed M Soldered on of the PC Board withthe longestlead on top Ri the Back Anode installed inthe round hole A side of DB side of and the shorter lead Cathode Board WEF Pc Board installed inthe square hole Step 3 Introduction to the Resistors and their locations The printed circuit board for the groLEDs kit uses two unique shapes and sizes of solder hole pads for assisting the kit builder in properly installing the 50 resistors LOOK AT THE PICTURE FOR THIS STEP CAREFULLY All 50 resistors are mounted on the back side of the printed circuit board All 50 resistors are mounted vertically with the body of the resistor residing over the larger round pad as shown and the flying lead in parallel with the body of the resistor being installed in the smaller octagonal pad as shown There are two different values of resistors 1 56ohms located at 40 different positions on the backs
21. lue LED body symbol on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs maintain their flat on the board position on the top side of the board BEFORE SOLDERING ensure that the flat edge of the body of all 5 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the highlighted locations in the assembly drawing in the picture for this step If they are all OK then Turn the board over and solder both leads of each LED at all 5 locations gt gt gt SAFETY NOTE rol Install White LEDs JameCo 2174881 at five places LED32 LED40 left of center LED37 LED38 and LED34 right of center f 6 Fan BR NT DQ 6n jco Onco lorn on ejon co oo oo io oo oo col FE 6n zgion co Oni co cO Og o on re jon 200 on SO l n ico 20 on ts on co ED oO GR a o0 log co On oO on lejon so 6ni o0 SE co of cojoni co ong cP co 6ni rOn ous 8 0 CO wn ep E Step 17 Assembly instructions for the next 9 resistors LOOK AT THE PICTURE FOR THIS STEP CAREFULLY Find the 560hms resistors JAMECO 690566 and remove 14 of them from their packaging Bend one of the leads down alongside the body of the resistor for each of the 9 resistors as shown in the picture for this step and as shown
22. n the next 3 INTRO steps prior to actual assembly work same luminous intensity in a 7 Give as standard Candles VERVER GNT BRIGHT as cru 30 different Blue et Bre opis change RA LEDs 1900mcd pays nee CUWA each 468nm 15 growing Dbl Viewing angle Most GROW Lamps are fixed in Spectrum e Bright Blue clear lens Narrow Beam spot 57 000mcd total 10 different White LEDs 8000mcd each dominant gt c r High Voltage can be aa Current z 5 very remote from Orne Limiters 650nm 120 gy OL s amp water sa Viewing angle ee l Broad White ef aw Power Connect l ANL Options Always diffused lens We ON Manual s or ON OFF Switch Wide Beam flood 80 000mcd total Relay Control et al Theg etl Os kitis small amp easy to mount where needed unlike larger commercial LEDs 8000mcd grade light assemblies Pg ae E Sime each 635nm 20 providing directed a pa I ap ERAR Viewing angle light where needed p ane 10 different Red x 274 Bright Red clear lens instead of broadcasting cs 5 lightin all directions lt PC Board Narrow Beam spot wasting most 1 95 x 2 60 80 000mcd total Step 2 Introduction to the Footprints The printed circuit board for the groLEDs kit uses four unique shapes and sizes of solder hole pads for assisting the kit builder in the assembly process
23. ocations Install 5602 JameCo 690566 at eight places R29 R26 R22 R23 R30 R25 R28 and R16 gt gt gt SAFETY NOTE DI0vGnon 99000 WOoG bond p 2000006 0 pi 0000000 7 pow i ms I ba oc Cc lt gt a ejje 0g TEOS ooo oo 0 agag 0 0 0HE qag 0 agg 06 Step 6 Assembly instructions for the first 8 Blue LEDs LOOK AT THE PICTURE FOR THIS STEP CAREFULLY Find the 5mm T 1 3 4 size Blue LEDs they each have a clear lens JAMECO 2193889 and remove 8 of them from their packaging The inset in the picture for this step depicts one of these Blue LEDs on its side on the top side of the board The longer lead the Anode is close to the round pad into which it is installed The shorter lead the Cathode is close to the square pad into which it is installed NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALITY At each of the 8 locations highlighted in blue on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs maintain their flat on the board position on the top side of the board BEFORE SOLDERING ensure that the flat edge of the body of all 8 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the blue highlighted locations in the a
24. on the board before starting this step Find the 5mm T 1 3 4 size Red LEDs they each have a clear lens JAMECO 2203813 and remove 5 of them from their packaging Remember when installing the LEDs the long lead goes in the round hole Anode and the shorter lead goes in the square pad hole Cathode NOTE THESE LEDS MUST BE INSTALLED CORRECTLY FOR PROPER FUNCTIONALITY At each of the 5 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the LED on the top side of the PC board bending the leads on the backside of the board to retain them in place while ensuring that the LEDs maintain their flat on the board position on the top side of the board BEFORE SOLDERING ensure that the flat edge of the body of all 5 LEDs are all facing towards the right edge of the board as depicted by the exaggerated flat edge of the red highlighted locations in the assembly drawing in the picture for this step If they are all OK then Turn the board over and solder both leads of each LED at all 5 locations gt gt gt SAFETY NOTE rol Install Red LEDs JameCo 2095171 at five places LED45 LED43 eft of center LED46 LED47 and LED42 right of center o 2O Fo pp O 00 Cm col bnlicoj niso o0 6a ss conu cg on 65n co on1 30 a cO of o poulco og hs e om co celon o0 L gt SO 6m oo Calce on a ogn co njeo hog F oO OF o IOO oO orn a 4 S om o o
25. ssembly drawing in the picture for this step If they are all OK then Turn the board over and solder both leads of each LED at all 8 locations gt gt gt SAFETY NOTE Install Blue LEDs JameCo 2193889 at eight places LED29 LED26 LED22 LED23 LED3O LED25 LED28 and LED16 x v 5 _ z g gt y Step 7 Assembly instructions for the next 5 resistors LOOK AT THE PICTURE FOR THIS STEP CAREFULLY Find the 100ohms resistors JAMECO 690620 and remove 5 of them from their packaging Bend one of the leads down alongside the body of the resistor for each of the 5 resistors as shown in the picture for this step and as shown in detail in steps 2 and 3 At each of the 5 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the resistor body over the large hole from the backside of the PC board bending the leads on the top side of the board to retain them in place while ensuring that the resistors maintain their vertical orientation on the backside of the board Turn the board over and solder both leads of each resistor at all 5 locations Install 100C JameCo 690620 at five places R46 R47 R42 left of center R45 and R43 right of center gt gt gt SAFETY NOTE y Step 8 Assembly instructions for the next 9 resistors LOOK AT THE PICTURE FOR THIS STEP CAREFULLY Find the 560hms resistors JAMECO 6905
26. stall LOOC2 JameCo 690620 at five places R50 R49 left of center R44 R41 and R48 right of center gt gt gt SAFETY NOTE LEDs Soldered Leads Oo oo io me 00g0 Oc OO O Oo At Keyi HO oo no Oc no G amp G aco gt oc no Oc Bo o Ge Co FES mo ao o no oo no uo Oc HO os no Oc go Oo EO oo no Oc no gt oo Oco OOS Cc Oo ob no oo mo no oc no oc no Oco Bo goo UC Cc no Oo HO oc no Oc no gt oo oc ao Oc OO oo UOC Oo mo Oc Mo Oc no Oo no o no Oc no Oc no Oo Hog guo Ooo oO go sos o86 009 Step 13 Assembly instructions for the next 9 resistors LOOK AT THE PICTURE FOR THIS STEP CAREFULLY Find the 56ohms resistors JAMECO 690566 and remove 9 of them from their packaging Bend one of the leads down alongside the body of the resistor for each of the 9 resistors as shown in the picture for this step and as shown in detail in steps 2 and 3 At each of the 9 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the resistor body over the large hole from the backside of the PC board bending the leads on the top side of the board to retain them in place while ensuring that the resistors maintain their vertical orientation on the backside of the board Turn the board over and solder both leads of each resistor at all 9 locations gt gt gt SAFETY NOTE Install 5602 JameCo 690566 at nine places R9 R
27. this step If they are all OK then Turn the board over and solder both leads of each LED at all 5 locations gt gt gt SAFETY NOTE rol Install White LEDs JameCo 2174881 at five places LED39 LED33 LED31 eft of center LED36 and LED35 right of center o 22 o 29 g0 00 OSD e59 cp 02 n colton oO 6nico om oo on ssiou sejon co Off c n Solon co on o r O ool 16r ZQ 6m colon col on so on on e io So om ie oni co 6 gt rejon i om 29 691 gt 61 cO Gn sp1Co lt e 90 cO oo isolen co of OAA colonj eion so ot ion co onl aac BLU Be sOn Tmt gp EP 5000 Step 12 Assembly instructions for the last 5 100ohms resistors LOOK AT THE PICTURE FOR THIS STEP CAREFULLY Find the remaining 100o0hms resistors JAMECO 690620 and remove them from their packaging Bend one of the leads down alongside the body of the resistor for each of the 5 resistors as shown in the picture for this step and as shown in detail in steps 2 and 3 At each of the 5 locations highlighted in red on the assembly drawing on the left side of the picture for this step install the resistor body over the large hole from the backside of the PC board bending the leads on the top side of the board to retain them in place while ensuring that the resistors maintain their vertical orientation on the backside of the board Turn the board over and solder both leads of each resistor at all 5 locations In
Download Pdf Manuals
Related Search