Home

Manual

1. Advanced Settings The Advanced Settings menu allows to handle the chart plotter functions The menu options are arranged in sub menus For example all options that relate to the Fix functions are in Fix sub menu See Par 3 5 for informations about Map Setting menu see Par 4 4 about Track menu see par 4 1 2 about Route menu see Par 4 1 1 9 about User Points menu and Par 4 5 about User C CARD menu gt MENU ADVANCED SETTINGS ENTER Once you are in the Menu use your cursor key to highlight the item and press ENTER to activate ot to proceed to the next selection menu 5 1 SETUP The Setup menu allows to enable or disable general options in the chart plotter handling See Par 3 5 3 about Auto Info option gt MENU ADVANCED SETTINGS ENTER SETUP ENTER 5 1 1 TIME REFERENCE Sets UTC or Local Time The default setting is UTC gt MENU ADVANCED SETTINGS ENTER SETUP ENTER TIME REFERENCE ENTER 5 1 2 TIME FORMAT Sets you preferred time between 12 hour and 24 hour The default setting is 24 hour gt MENU ADVANCED SETTINGS ENTER SETUP ENTER TIME FORMAT ENTER User Manual ooo 5 1 3 DATE FORMAT Sets you preferred date between MM DD YY month day year and DD MM YY day month year The default setting is MM DD YY gt MENU ADVANCED SETTINGS ENTER SETUP ENTER DATE FORMAT ENTER 5 1 4 WIND SPEED Selects th
2. ENTER A window is opened select YES and press ENTER to confirm select NO and press ENTER otherwise The route remains on the screen shaded until the screen is redrawn To delete the route see also Par 4 1 1 4 and 4 1 2 2 68 User Manual 4 1 2 8 Safe Route Checking This function checks the presence of particular cartographic objects see the list below on a range set by the user for all route legs e Land Areas Shallow Water e Intertidal Areas e Rocks e Wrecks e Obstructions e Shoreline Constructions Fishing Facility e Dreged Areas Diffusers e Mooring Warping Facility e Production Installation gt Pingos e No Data Available If any of these alarm conditions is detected the function returns the list of dangerous objects and the relative dangerous route leg that is drawn with a different color It is possible to make the Safe Route Check from menu following the procedute gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE CHECK REPORT ENTER of gt Place cursor on route leg ENTER ROUTE CHECK ENTER The list of the dangerous objects found on the charts crossed by the route 1s shown in the route check report It is also possible to activate this function in automatic mode gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER AU TOMATIC CHECK ENTER ON ENTER If Automatic Route Check is activated the modified Route legs are checked ever
3. ENTER Defines the range from the fix within which the AIS Target becomes active The values allowed are from 0 1 to 20 Nm The default setting is 5 Nm 5 7 2 3 CPA Alarm gt MENU AIS SETUP ENTER CPA ALARM ENTER Turns ON ot OFF the alarm The default setting is ON 5 7 2 4 CPA Limit gt MENU AIS SETUP ENTER CPA LIMIT ENTER The values allowed are from 0 1 to 10 Nm The default setting is 0 5 Nm 5 7 2 5 TCPA Alarm gt MENU AIS SETUP ENTER TCPA ALARM ENTER Turns ON ot OFF the alarm The default setting is ON 5 7 2 6 TCPA Limit gt MENU AIS SETUP ENTER TCPA LIMIT ENTER The values allowed are from 1 to 30 min The default setting is 10 min 5 7 5 TO SET THE CHART PLOTTER FOR RECEIVING AIS Make sure that the AIS receiver is properly connected to the chart plottet The chart plotter reads the AIS NMEA message VMD type 1 2 3 and 5 Select the used serial port and transmission speed by following the procedure gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT n INPUT ENTER m ENTER Where n Port 1 Port 2 Port 3 m NMEA 0183 4800 N81 N NMEA 0183 38400 N81 N according to the transmission speed of your AIS receiver 5 7 4 QUICK INFO ON AIS TARGET By placing the cursor over a AIS target icon the following information is displayed Vessel Name MMSI number Radio Call Sign SOG COG BB User Manual
4. 3 5 6 GETTING TIDE INFO When you will see a Tide Info icon you can click on it to query the available infor mation that will immediately be displayed User Manual S Tide Info icon HEH x POSITION SE 42 54 264N 008 19 311E fees SOG Kts COG M 4 0 000 MAP DATUM HGS 1984 SCALE 6 Z Nnm Fig 3 5 6 Tide Info icon Place the cursor on the Tide symbol a Automatic Info window is opened Ge POSITION 42 54 284N OBJECT 008 19 311E Tide height SOG Kts COG m TO CURSOR ST Hu BRG M MAP DATUM WGS 1984 SCALE HH 26Nm Fig 3 5 6a Automatic Info on Tide To display the Tide Graph page press ENTER Values referred to the VERTICAL cursor Values referred to the HORIZONTAL cursor EET VERTICAL cursor Height H Ab Ft Drsught 6 65 Ft i di EG e 61 61 97 1 el mi e eae HORIZONTAL cursor 43 32 860N 010 18 022E 0 18 Port Info O 2 4 6 B i0 12 44 46 18 20 22 24 LIVORNO LEGHORN High Water max 0 86 Ft 13 39 L Low Water min 6 35 Ft 21 66 L Sunrise 67 52 L Sunset 16 53 L Fig 3 5 6b Tide Graph Using the cursor key it is possible to move the cursor anywhere on the graph and display the time height vertical cursor and draught horizontal cursor on a particular graph point Also use ZOOM IN or ZOOM OUT to go to previous or next day and ENTER to set date move the cursor key up down to insert the preferred number a
5. ENTER Points Of Interest ENTER Lat Lon Grid On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Lat Lon Grid ENTER Chart Boundaries On Off Auto The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Chart Boundaries ENTER User Manual o Value Added Data On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Value Added data ENTER Chart Lock On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Chart Lock ENTER Underwater Objects Limit Selects the max depth value to display Underwater Objects The default setting is 3Mt gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Underwater Object Limit ENTER If value is set to 0 Mt the Underwater Objects are not shown on the charts Menu options are greyed out If value is more than 0 Mt i e 10 Mt in the Range from 0 Mt to the selected value the Underwater Objects are displayed according to their setting below Rocks Off Icon Icon Depth The default setting is Icon gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Rocks ENTER Obstructions Off Icon Icont Depth The default setting is Icon gt MENU MAP SETT
6. gt MENU ADVANCED SETTINGS ENTER TRACK ENTER DELETE ENTER Deletes the all track storing After pressing ENTER a warning window appears select Yes and press ENTER to confirm select No otherwise 4 5 6 DELETING SELECTED TRACK gt MENU ADVANCED SETTINGS ENTER TRACK ENTER DELETE SELECTION ENTER Deletes the track selected After pressing ENTER a window appears press ENTER to set the first point then press ENTER to set the second point A warning window appears select Yes and press ENTER to confirm the deletion select No otherwise User Manual 77 4 5 7 SELECTING TRACK MEMORIZING TYPE gt MENU ADVANCED SETTINGS ENTER TRACK ENTER STEP UNIT ENTER Choose Distance Dist the chart plottet can store a fix when the distance from its last stored position is greater than a defined distance Time the chart plotter can store a fix after a defined time Auto the software decides when storing a position on the basis of the straight or curved track The default setting is Time 4 5 8 SELECTING DISTANCE gt MENU ADVANCED SETTINGS ENTER TRACK ENTER DISTANCE ENTER When the tracking function is On and the type of track storing is Distance you can store a fix when the distance from its last stored position is greater than a defined distance Choose in the range 0 01 0 05 0 1 0 5 1 0 2 0 5 0 10 0 Nm the di
7. message and starts the acoustic alarm The default setting 1s Off gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER AN CHOR ALARM ENTER 5 5 4 DEPTH ALARM Sets an acoustic alarm to sound when the received depth value from the depth transducer 1s too shallow The default setting 1s Off gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER DEPTH ALARM ENTER 5 5 5 EXTERNAL ALARM When any alarm condition occurs the pin 1s switched from High Impedance to ground This signal can be used by an external device as a hooter or buzzer The default setting 1s On gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER EX TERNAL ALARM ENTER 5 5 6 GROUNDING ALARM GUARDIAN TECHNOLOGY The chart plotter is provided with a function that by querying the map s data vetifies potential danger to navigation due to shallow water land rocks obstructions and shoreline constructions The maps are scanned periodically every 10 seconds When the Grounding Alarm 1s active the chart plotter scans an area in front of the boat This area 1s identified by a triangle drawn in front of the boat icon whose direction is determined by the current boat heading The length of the triangle is user selectable and its angle is 30 degrees If any of the above objects are found the chart plotter notifies the danger on a dedicated warning message box in the Grounding Alarm Report page see Par 5 5 9
8. rarnnrrnnnnnnrnnvvnnnnnnevnnennnennr 50 124 PIN E 100 place Per 21 place en 21 plate MOB sacarse emafi 20 place Waypoint is ccoxsescagumsnnisaioebersecumptedes 21 Placing EBL amp VRM ronnnnnnnnnnnnrn 21 74 Points Of Interest 15 16 46 47 57 Points per Track saadan 14 Port 1 2 3 4 5 NMEA Output 36 Port 129 45 Output n se 36 Port 12345 NDUT treguedebestege geed 39 Port CARE 56 Port By Name st nad 16 55 Port Info nonnene 40 53 124 Port information 2 eies esgeggeeg ebeue ecirgen 15 Port Services sincieceusssesdesevaniebeveestsenbavades 55 Ports amp Services 15 46 47 53 124 Position Filter ansesarnnesdaees 15 Position Request eeekptekstrstesgsbes eniieter 102 POWER EE 19 22 Power consumption ssnnnnnnnrnnnvnvennnn 17 Presentation Features A 40 EE 107 PTX lav 107 PTX information Window rannnnrnnvnnn 108 PTX LIST PAG n den 108 PTX warning message n 107 Q Quick Info naasna 40 50 85 98 105 Quick Reference rrrnrrrnnnrvrrrrnerennnnnn 115 R RADAR uo ccccceceecceeeeeeeeeeeeeseeseeesseseeaes 21 Radar EE 16 37 110 Radar Page bececiencesessvaeieneneicacaxdaces 21 110 RAM Clear cccsscssesseseeeeeeees 115 117 User Manual RAM Engt ditggegrguegedeteedegreggeggt eet 117 RAM Test 117 Real Time View rrrannnrnorrrrnnnnrrnvnnnnnnr 101 Receive route 67 Receive User Points rrrnnnnnnnnnnnnnnnnnnne 66 Removing C CARD AA 27 Reset
9. 84 4 8 1 6 Graphical representation on Map Display 84 4 8 1 7 Route Data TRO DOM scsirensoteeissincsnpaccessesiscsiaeradeecsusuvteaneress 84 4 8 1 8 Quick Info szccacortenchiiesastaxcumiesedateacuctstaneeetoatadenededexendvones 85 Route Navigation Quick Info on the Destination 85 Quick info on Single Destination rrrrnnrrnerrrnnvvvrrnrn 85 ANTENNE surasini rnanan nA Era EAEEREN EERE EARE RA REEERE 87 EP 87 SJ WR Man E e 87 312 EE NN 87 J NNN 88 S14 Wind De SO EE 88 User Manual User Manual 5 2 5 3 5 4 52 5 6 5 7 5 8 5 9 e BENN ee e mienes cnertert 88 El External Narr 88 SN EE a ln Elie 88 KZ 88 ER OU SC ON ERE ENER 89 5 2 2 NE TEN penn 89 5 23 E Reen 89 524 PET FINGI E 89 525 DCC FINCK eet 89 IN OID EE 89 527 ar FeO OM ING secies pirri niron EESE ERATES 90 528 Statie Navigator EE 90 ME vn 90 531 Cord SEN saassscnsecccanardveoininensrtxecealnaieienssdnindesiontaninedenens 90 RE EEE EE EE 90 EN MN 91 5 3 4 Orientation Resolution wzceceuscvnsncsevenxsneuvspaneunsvnnmiantediedextiensertoumertnce 91 5 3 5 Roll EELER 91 5 3 6 Reset Partial and Total Trip cxssnssiscspaxcuncpnddesnvanessanddenidenibenseoimersene 91 COMPASS EE 91 PE Ne 92 TL NN 92 5 4 3 NNN 92 ALARMS OR EN EE 92 551 AN 92 SE MEN E 93 553 MUNN 93 SoA PT FAI EE 93 555 FAM 93 5 5 6 Grounding Alarm Guardian Technology 93 5 5 7 Grounding Alarm Range EE 94 5 5 8 Grounding Alarmi Width ME 94 5 5
10. ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE REVERSE ENTER Reversing a route plan is most typically used to return to the point where the route originally started 4 1 2 5 Route color gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE COLOR ENTER A window ts opened use the cursor keys to select the route color you want among the eight colors available Press ENTER to confirm The route appears on the screen colored by the selected color It is possible to select a different color for any route 4 1 2 6 Send Receive route To transmit the active route information onto the NMEA output pott gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER SEND ENTER The NMEA WPL amp RTE messages are sent to the output pott To save route information received from the NMEA input port gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER RECEIVE ENTER The received route is saved on the active route overwriting it The NMEA WPL amp RTE messages ate sent to the input port 4 1 2 7 Finding information on route Route Report gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE REPORT ENTER It there are more than 8 Waypoints shown use the cursor key to select another page User Manual EE Waypoint number ROUTE REPORT REPORT Fuel consumption between the Waypoint and BRG LOST TOST I TIME g UEL the previous one W
11. Speed Over Ground Speed of the Vessel relative of the Water PAE TRI 6 4 4 w d Bue 2 me Over Ground KS Water Temperature 40752 150N 011729 B ZE gt J Ship s Coordinates ro nest m Velocity Made Good s9Z2 13m w 156 KEES Bearing Out of route Depth Fix Status icon Distance Cross Track Error Time To Go R Right or L Left Fig 3 1 4 Navigation Data Page Ya CS eer Manual 3 1 5 3D NAVIGATION DATA PAGE The 3D Navigation Data page shows in graphic mode navigation data Distance Compass graphic indicator Time To G Speed of the Vessel sia relative of the Water Depth Water Temperature Bearing Speed Over Ground Fig 3 1 5 3D Navigation Data page 3 1 6 WIND DATA PAGE The Wind Data Page shows data related to the wind TWS True Wind Speed Velocity of the Wind relative to a fixed point on the earth AWS Apparent Wind Speed the Speed at which the Wind appears to blow relative to a moving point also called Relative Wind Speed TWA True Wind Angle and AWA Apparent Wind Angle Also SPEED Ship Speed and HEAD Ship Heading are shown Fig 3 1 6 Wind Data page 3 2 BASIC SETTINGS The Basic Settings menu provides access to the set up functions Here you can choose the language you want see Pat 2 4 Fot Page Preview option see Par Sek gt MENU BASIC SETTINGS ENTER User Manual 3 3 2 1 COURSE
12. The Grounding User Manual 9 Alarm is switched Off by default after a Master Reset Once the Grounding Alarm has been activated a warning message is shown gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER GROUNDING ALARM ENTER Note The Grounding Alarm function only operates with the new C CARDs It also affects the speed of the redraw of the screen If this function is not used it maybe disabled 5 5 7 GROUNDING ALARM RANGE Allows setting the length of the sector to be detected among 0 25 0 5 1 0 Nm The default setting is 0 5 Nm When any of the searched objects is found in the scanned area a tick marker is printed on the relative box in the Grounding Alarm Report page see Pat 5 5 9 to identify which dangerous objects have been currently detected gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER GROUNDING ALARM RANGE ENTER 5 5 8 GROUNDING ALARM WIDTH Allows setting the length of the sector to be detected among Thin Medium and Large The default setting is Large gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER GROUNDING ALARM WIDTH ENTER 5 5 9 GROUNDING ALARM REPORT Allows displaying the report of the dangerous objects currently detected gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER GROUNDING ALARM REPORT ENTER 5 6 SIMULATION The built in Simulator function allows you to become proficient in the us
13. Use the cursor key to select the port and ZOOM IN ZOOM OUT to select next previous page Press ENTER to locate the selected Wreck on the map 3 5 7 4 Finding Obstructions Searches for nearest Obstructions gt MENU FIND ENTER OBSTRUCTIONS ENTER Use the cursor key to select the port and ZOOM IN ZOOM OUT to select next previous page Press ENTER to locate the selected Obstruction 3 5 7 5 Finding Port By Name To select the Port By Name function following the procedute gt MENU FIND ENTER PORT BY NAME ENTER User Manual aS Shows the list of all ports stored on the C CARD in alphabetical order and allows to search ports by name to locate the ports on the map 3 5 7 6 Finding Port By Distance To select the Port By Distance function following the procedute gt MENU FIND ENTER PORT BY DISTANCE ENTER Shows the list of all ports stored on the C CARD in closest distance order and allows to locate the ports on the map 3 5 7 7 Finding Lakes Information Seatches for nearest Lakes Info gt MENU FIND ENTER LAKES INFO ENTER It founds the Outdoor Recreational Area objects See the following picture FIGHING OMEN EE Ia C lt 3 i oi Loo O e rr i j Fig 3 5 7 7 Outdoor Recreational Area objects Use the cursor key to select any objects and press ENTER The list of the nearest lakes containing the facility will be shown on the
14. 100 User Manual 5 9 1 3 Weather Forecast gt MENU C WEATHER SERVICE ENTER FORECAST ENTER Allows selecting the Layer of specific weather data to be displayed on the screen and to change date and time of the forecast preview The following functions are available Panning Default usage of the cursor key is the normal panning function Zoom In Out Zoom in out functions ate allowed as usual by using ZOOM IN ZOOM OUT Set Date and Time ENTER to modify date and time values Layer Selection PAGE to cycle the weather layers Exit CLEAR to close the weather prediction page 5 9 1 4 Real Time View gt MENU C WEATHER SERVICE ENTER REAL TIME VIEW ENTER The following selections are available Real Time View On The data is shown the area of the download at the current date and time received from the GPS Real Time View Off The Weather data is not displayed The layer displayed is the one selected into the previous menu item 5 9 1 5 Type of Data gt MENU C WEATHER SERVICE ENTER TYPE OF DATA ENTER Allows selecting the type of data see the previous Fig 5 9 5 10 DSC The DSC Digital Selective Calling is a method of establishing a VHF radio call it is used to announce urgent maritime safety information broadcasts This system allows mari nets to instantly send Distress Call or and Position Request to the other vessels equipped with a DSC transceiver within range of the transm
15. Fish ne 16 Chart Boundaries aaaaaaaaaaan 15 46 47 Chart Language 000ee 15 49 Chart Lock uns 15 44 46 48 122 Te 18 Glatt POET Olav 19 chart POE Osnes 19 127 Chart plotter setze 17 Chart plotter weight AAA 17 Charts and text area ennnnnnnnrrvrrrrnrn 30 EE ee 19 Clear Info anne 40 Clear VIGEN scescctsoncesnenecdssndeseccbocedumncestebses 40 CG RE 32 122 Compass Calibration ME 16 Compass un TE 91 CONV ASI eege 117 CONVENTIONS rarrorrrvrvvenerrerernsnnnnnnnn 13 Coordinate System rrvrrvrrrrrrrrnrnnnnnnnn 15 Correction rrrrvvvurvnvarnvvverevvnrevenr 89 122 Course Vector escena 16 34 122 GEER 96 CPA Alarm sanee 96 98 CPA Um 96 98 Creating a route rrrnnnnrnrrrrrvrvrrvevvrrerrn 60 Cross Track Error suvneseiresdessdaasssid 126 CT nn 122 Cultural Features rrrrrvrrvrrvrrnrrvveveen 122 Currents Prediction keen 15 45 Cursor Control Lussnenasnerrsmmedsne 17 cursor key assssnssonssnnnnensressrernrneeeene 18 20 D Dangerous Target cccceeeeeeeeeeeees 97 Data E 40 Data Safety Indicator rrrnnnnnnnnnnnnnr 44 Datum revrrrvrnrevnrnrnnevvnrnnnnvrnnnvavenne 90 122 Dead Reckoning errvrarrvrnrrvnvrnrnnnnnnnnnn 16 DST UE EEE 122 Deleting EBL amp VRM nsee 75 Deleting Event rnnnnnnnnnnnnnnnnnnnnennevene 73 Deleting File asc ccancascusssratyespnicenexeusseatinniaes 80 Deleting EE 70 Deleting MOB ssasscdsesexccpexevaseantcv
16. Ship ICOM Mode egiiestngeegeeeeegreedegieeguegce 88 Show Ca E 109 SIM PIN csiascusectusshans spdcecersotsaimeaenaesscwes 100 Simulation aiseee 17 94 gt EE ER 17 User Manual Slave Chart Plotter c cccscceseeees 83 Sleeping Target sssssscsceeeeees 97 Smooth Zoom rrvvnvrnnnnrevvnvenvsvnevvnr 15 41 e e E 32 OE EN 32 124 DUSCHICAUONS asxasivvesnsvariesanessalpnadnbotieatins 14 Speed Reen 33 34 68 124 Speed Filter wianantavivssnsniaieagwarsmncnddwennsiennia 15 SJ Os ee LNI EN 16 Spot Soundings rronenenvnnnnnnnnnnnne 40 124 Static Navigation srnr0r0rorrerrreerereenr 16 SJEL Io EE 124 S EEE 124 SEE ES ERE 116 System Update rennnnnnnvnvrvvrvrvrrerereser 116 T Target 0 20 30 39 61 62 71 73 96 97 124 EP E PAE 96 TOPA Alarm EE 96 98 TOPA Limit EE 96 98 EE 15 90 125 Temperature eessen 17 35 Temperature Un 17 TENNO E 121 He 53 55 125 Tide amp Currents a an 15 40 125 Tide Peke 54 Tide Height verre 52 Tide Info EE 53 125 Tide Stations rrrurrnrvnvnrenvnrvvvunnern 16 55 Tides amp CGumrents 15 46 Tides Preview cccccccsssssesssseeeeeeeeeeeees 40 len a8 sass Seton A 14 Time Simulation esend giess tege 95 time Tee 78 Time Difference uk 125 Time Le 125 Time top 39 62 126 ETE 22 FRA I N E E 21 Re if HACK COOL EE F Track memorizing type 05 78 Track ON 21 77 TCR E 14 Tracks
17. amp Receive Marks Routes enken 36 EL EE eege 37 3267 PN NE 37 3 2 8 8 Cable Wiring Pages uuassmmeemmmenimntiensiriens 37 32 9 ee MENU EE 37 E INI 0 E 37 2 ENN riene 37 N Pan 38 A B C D FUNCTION eegenen 38 3 3 1 Inserting the A B C D POM CN 38 3 3 2 Deleting the A B C D points sovasevessnsacesneessntuenrmucsinaeiisesenedserceane ines 38 3 3 3 Navigating on the A B G D points Laseemsssekaesnssidne 39 NAVIGATING TO A SINGLE DESTINATION c ssccceceesesessteeeeeees 39 3 4 1 Distance and Bearing to Target EEN 39 SE ENN 39 3 4 3 Deleting TT 39 C MAP By Jeppesen MAX CARTOGRAPHY INFORMATION 40 3 5 1 Map Settings Menu iiassnsssinsieccwananamndvactniavenntdavedieisesduecciniuassnidetsin 41 3 5 1 1 3D View Perspective View 41 DEL E 42 3513 Map SEE 42 DE LOOM KEE 42 Fl HEH HEEN 43 3 5 1 6 Dynamic Nav AidS scxcessisnienisctuecutancesnentecenarvadeescdeaveesneres 43 Laly LEN ege 43 3 5 1 8 Safety Status Bar DSI Data Safety Indicator 44 3 5 1 9 Satellite Imagery EE 45 3 5 1 10 Currents Prediction BEE 45 3 5 1 11 Other Map Configurations e teen e t geesde 45 3 5 1 12 Selecting the Chart Language AER 49 3 5 2 Getting Automati NIO EE 49 3 5 2 1 Info on objects with Pictures rrrrrrrvrrvrvvrvvrrrrrrnrnnnnnnnn 50 Change le E 50 3 5 2 2 Quick Info on E 51 EE MO e 51 3 5 3 Info Tree and Expanded Info page rrrrnnnnnnnnnnnvnrnrrnrnnnvvenererreren 52 NNN 52 39 0 GE WING PON INIO EE 53 35 6 ENTEN 5
18. e C Link C Weather Service and C Staff e AIS Automatic Identification System e DSC Digital Selective Calling e MOBILARM System Fish Finder capability if connected to Fish Finder Black Box Radar functions display if connected to Radar scanner e Automatic Info e Find Port Services Tide Stations Wrecks Obstructions Port By Name Port By Dis tance Lakes Information Lakes By Name Points Of Interest Navigation to Destination Speed Unit Mph Kts Kph 16 User Manual e Distance Unit Km Nm Sm e Depth Unit Ft FM Mt e Altitude Unit Ft FL Mt Temperature Unit C F e Alarms Handling Arrival Alarm XTE Alarm Anchor Alarm Depth Alarm Grounding Alarm Ground ing Alarm Range Grounding Alarm Report e MOB Function e Simulation Speed Heading Date Time Cursor Control Activate Simulation Auxiliary Memory User C CARD 1 2 4 MB Interface 3 I O ports Note If connected to Fish Finder Black Box and or Radar scanner 1 2 1 2 Physical Characteristics Controller size inch mm 6 8 x 4 2 x 3 2 172 5 mm x 106 5 mm x 80 2 mm Controller weight 600 gr Display Resolution 640 x 480 or 800 x 600 or 1024 x 768 pixels user selectable Video Output Compatible VGA optional adapter cable Power consumption 2 5 Watt max a 35 Volt de Operating Temperature Range from 0 C to 55 C from 32 F to 131 F Memory e Non volatile with battery back up Keyboard e Silicon rubber backlight
19. that disappears when the cursor is moved from the Target When the Target is placed all navigation data are referred to this Target Note When the chart plotter is turned Off the Target does not remain in memory 3 4 2 TIME TO GO When the Target is set the TTG value is displayed in the Graphic Data Page gt PAGE more times to select the Graphic Data page Note If SOG value is less than 1 0 knots or the BRG is greater than 90 degrees the VIG value is not displayed 3 4 3 DELETING TARGET Place cursor on Target icon press CLEAR the symbol identifies Target disap User Manual BD pears from the screen Otherwise when the cursor is placed in a genetic position on the chart press DEST A window appears to advise that the Destination is present select the item STOP and press ENTER the symbol identifies Target disappears from the screen Note Tf you select the SVART item and press ENTER the Target icon is moved on the new cursor position 3 5 C M P Brenn MAX CARTOGRAPHY INFORMATION MAX is a major evolution of the product technology Key points are Data Features ISO Certification electronic chart production process with quality certification Extra Large Coverage all the C MAP By JEPPESEN electronic chart detail and a huge coverage without having to change cartridge Official data source data based on use of official data sources Detailed World Background worldwide background chart with deta
20. 1 FILE 1 MRKS 2 SAVE FILE EVTS MEG WPTS EVENTS 5 ROUTES 07 02 98 FILE 1 TRACKS 017 01 80 FILE 3 I MARKS i 1 1 80 i Je FILE S MARKS 01 01 80 i 90 00 00 RIES LOAD DELETE FORMAT CHANGE Fig 4 6 1 Save File function 1 Select the file name At first a default name 1s shown use the cursor key to insert the name Press ENTER Select the data type to save among MARK EVENT ROUTE ot TRACK Note When naming a file you may have trouble finding a name that uniquely identifies the file s contents Dates for example are often used in filenames however they take up several characters leaving you with little flexibility The secret is to find a compromise a point where you can combine a date with a word creating a unique filename The maximum length of the filename is 8 characters The characters may be numbers 0 9 letters A Z and spaces for example legal identifiers are ABC AA 12121212 ABC 1 AT and so on Press CLEAR On the screen appears USER C CARD or FILE 1 D OG OG D OG OG OG OG D OG OG 60 60 60 077 02 98 I 17 17 00 i ROUTES I 07 02798 17 17 00 I TRACKS 01 01780 i 00 00 00 TRKS MARKS 01701788 90 00 00 566 FILE S i MARKS 81 61 80 op 00 00 MRKS 2 EVTS 2 WPTS 5 SS LOAD DELETE FORMAT CHANGE Fig 4 6 1a Save File function ID 4 6 2 LOADING FIL
21. B2 Kts COG M 4 0 000 G hi HAYPOINT TO CURSOR ROUTE1 HPT 3 S Im BRG 400N ST Nm BRG M 43 10 S 010 16 159E 3 86 65 0799 for options b gt MAP DATUM WGS 1984 SCALE 16Nm Fig 4 1 1 3 Deleting Waypoint 1 lb User Manual Press ENTER Select DELETE and press ENTER The Waypoint is deleted and a new line between previous and next Waypoint is shown The deleted Waypoint te mains shaded until the screen is redrawn POSITION p 42954 496N Eg em 008 19 311E WPT BI WPTA32 V T pm I S0G Kts COG A J DST Nm BRG 075 A WPT G7 MAP DATUM WGS 1984 V SE f i 4 SCALE EN Kebab Fig 4 1 1 3a Deleting Waypoint II WPTG66 4 1 1 4 Deleting route gt Select Advanced Mode Place cursor on Waypoint Press ENTER Select DELETE ROUTE and press ENTER A window is opened select YES and press ENTER to confirm select NO and press ENTER otherwise The route remains on the screen shaded until the screen 1s redrawn To delete route see also Par 4 1 2 2 and 4 1 2 4 4 1 1 5 Distance and Bearing to Target Once you have positioned the cursor on the desired starting Waypoint it could be the first Waypoint of the route or another one press DEST A circle surrounds the Waypoint symbol A line is shown connecting the Target with the ship s position When the Target is placed all navigation data are referr
22. Background Update The System Update menu is entered from the About Page To select this menu follow the procedute gt Plug the special data C CARD MENU About ENTER MENU Up DATE WORLDWIDE CHARTS ENTER 6 7 SYSTEM TEST If you have connected your position finding device according to the instructions and chosen the proper menu selection for your device and are still having problems with your chart plotter the extended auto test should help determine the problem Make sure the chart plotter is turned Off While pressing and holding any other key turn the chart plotter On A new menu will appear on the display Software name and version XXXX V X yy SYSTE M TEST NTSL V x yy zz R gg mm yyyy RAM menu Dim menu Cartridges Serial ports Modem Test EXTERNAL ALARM NT Software Library version and date Fig 6 7 System Test Use the cursor key to select the preferred test this will display in reverse video and with the relative menu window To choice the test press ENTER To exit from any submenu Mb CU se Manual press CLEAR To exit from the System Test turn Off the chart plotter 6 7 1 RAM MENU This test verifies the integrity of the memories and if preferred during this test all the internal memory can be erased and the default setting restored m RAM Test To vetify the integrity of the RAM If on the screen the message ERROR appears the RAM is physically damaged E R
23. Chapter For the Experienced User introduces the advanced features of the chart plotter 1 1 CONVENTIONS Throughout this User Manual the labelled keys are shown in capitals letters en closed between single inverted commas for example MENU Menu operations are in bold characters listed by keys sequence with the menu names enclosed between tnverted commas for example MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER means press the MENU key using the cursor key select the Basic Settings menu and press ENTER using the cursor key select the Input Output menu and press ENTER Terms underlined for example Mark are explained in the Appendix Terms 1 2 FEATURES The chart plotter is a computer specifically designed for nautical use but more precisely to ease and speed up all calculations which so far have been done manually If User Manual o B connected to a positioning instrument the chart plotter displays the current position the speed and the heading of the boat and its Track The user information like Waypoints Marks and Tracks can then be stored on a User C CARD and can be recalled at any time On the screen are shown navigation data and cartographic information obtained from elec tronic charts of C MAP By Jeppesen C CARD When the package containing the chart plotter is first opened please check it for the following contents if any parts ate missing contact the dealer the chart plotter was p
24. Currents Lagmesmtsminnseise 40 Dynamic Elevation Data 41 Dynamic Nav Aids 15 40 41 43 E EBI EEE 74 123 EBL amp VM 16 EBL amp VRM function csan 74 ECHO 21 Echosounder ccccccsececeeeeeeeeeeeeeeeeeeees 37 Editing EBL amp VRM rrnnnnnnnnnrnrrnrvrnnnn 15 Editing RE 73 FANG MATK anden 71 Editing WAP EE 64 electronic charts ccecce 14 Enhanced Mixing Levels 41 Enhanced Port Info 40 Enhanced Turbo Zoom 0 eceeeeees 41 EEN TERR EE 19 EEE 85 20 Event 20 73 74 123 Expanded N O inesontntatsasionnaniveiaaseesierese 52 External Alarm earevrrrnrnrevnrnrnnenrnrnnnr 118 External Alarm Connection 25 114 External bracket cccccceccseeeeeeeeeeeeees 14 User Manual External NMEA Connections 24 114 External Route erccscwisensciensssansinanioenendwaseinets 84 External Signal cccestussasieisernssdtoetaadwnsenice 37 Extermmal WINING cscessaisiesdiveiveneisectnancests 112 Extra Large Coverage EEN 40 F FEATURES Leer 13 EN 79 80 123 EEE 89 e EEE ERE 40 Find Function rrvrrrnvrevnnevnnennnnnnnnr 16 55 Finding Lakes By Name 16 57 Finding Lakes Information 16 56 Finding Obstructions s 16 55 Finding Points Of Interest 16 57 Finding Port By Distance 16 56 Finding Port By Name l a 16 55 Finding Port Services c0608 16 55 Finding Tide Stations 00000000 16 55 Fin
25. Grid system used on most large and intermediate scale land topographic charts and maps m VAD Value Added Data Collection of additional cartographic objects which are not present on the original paper chart from which the electronic chart derives These objects have been obtained from other sources and then merged to the electronic charts in order to provide more information useful for the navigation VAD object can be any cartographic objects and it can be distinguished from the official chart objects from the Quick Info A dedicated icon is shown on the Quick Info window to indicate that the object queried is a VAD The same icon is also shown on the Full Info page and in addition the extended text Value Added Data is shown on the details of the VAD object m VMG Velocity Made Good Destination closing Velocity The VMG 1s calculated using the current speed of the vessel SOG and the difference between the current vessel course and the bearing to the destination m VRM Variable Range Marker Circle with radius selectable by the uset E WAAS Wide Area Augmentation System The Federal Aviation Administration FAA in cooperation with other DOT organizations and DOD is augmenting the GPS SPS with a satellite based augmentation system the WAAS It will provide a signal in space to WAAS usets to support en route through precision approach navigation After achieving initial operational capability the WAAS will then be incrementally imp
26. Navigation Leg RED Line m 3 Fig 4 8 1 6 Graphical Displaying 4 8 1 7 Route Data Report When the Navigation to the External Route is received it will be possible to display the information related to the External Route by entering the Route Data Report External Route ROUTEOO1 Cruising Speed 12 5 kn Fuel Consumption Rate 8 0 l h Total Route length 71 19Nm Total Fuel Consumption 45 51 Waypoints in Route 4 Initial Fuel Load 255 I Remaining Waypoints 4 Remaining Fuel 209 I DST TTG ETA Cons inmi Uh mm hh mmm Lit To Dest To Heid Wot To Last Wpl Fig 4 8 1 7 External route on Route Data Report External Route name of the External Route from PCMPN 0 Cruising Speed planned cruising speed from PCMPN 1 Fuel Consumption Rate planned fuel consumption rate from PCMPN 1 e Total Route length Route length from first to last Wpt from PCMPN 1 Initial Fuel Load volume of fuel available before the navigation was started liters Total Fuel Consumption calculated fuel consumption to navigate the whole Route 0 User Manual Waypoints in Route Remaining Waypoints Distance to Destination Distance to Next Wpt Distance to Last Wpt TTG To Destination TTG To Next Wpt TTG to Last Wpt ETA to Destination ETA to Next Waypoint ETA to Last Wpt 4 8 1 8 Quick Info EXTERNAL Rte ROUTEON DST Tit Cons inmi hh mm Lit Dest 1193 00 57 7d No of Wpts in the Route
27. Nm Nautical Miles Sm statute miles Km chilometres The default setting is Nm gt MENU BASIC SETTINGS ENTER DISTANCE ENTER BAC eer Manual Depth Ft Feet FM Fathoms Mt Meters The default setting is Mt gt MENU BASIC SETTINGS ENTER DEPTH ENTER Altitude Ft Feet FL Flight Level Mt Meters The default setting is Mt gt MENU BASIC SETTINGS ENTER ALTITUDE ENTER Temperature C F The default setting is C gt MENU BASIC SETTINGS ENTER TEMPERATURE ENTER 3 2 7 NAV AIDS PRESENTATION Allows to set the Nav Aids presentation as US or INTERNATIONAL The de fault setting is INTERNATIONAL When selected it affects Lights Signals Buoys amp Bea cons display International Draws Nav Aids using international symbology All components of Complex Objects are shown US Draw Nav Aids using NOAA symbology All components of Complex Ob jects ate shown gt MENU BASIC SETTINGS ENTER NAV AIDS PRESENTATION ENTER 3 2 8 INPUT OUTPUT MENU WARNING gt gt After every software upgrade the RAM is cleared and the chart plotter re starts with the usual default settings Please 20 to the Input output menu and set the proper input format once again 3 2 8 1 Port 1 Port 2 Port 3 Port 4 Port 5 Input Sets or disables the format for the navigation data input serial Port 2 3 4 5 The default setting is NMEA 0183 4800 N81 N For e
28. Page see Par 5 11 4 3 Both Goto and List functions also mute the Audible Alarm Note The List function is active if more than one PTX is store 5 11 3 2 PTX is received again When PTX has been received again it is already present on the chart plotter memory If the received PTX is NOT the active one the user must confirmed to navigate to It Otherwise if the received PTX is the active one the PTX on which we are navigat ing to navigation data ate updated in memory the new PTX coordinates becomes the Destination position and the current Fix position becomes the starting position The map 1s not automatically centered on it The PTX icon appears at the new position and a pop up warning window appears It is possible to close all menus data pages if open and center the chart on the received PTX see Par 5 11 4 4 Otherwise you could close the alarm window and stay on the active screen 5 11 4 MOVING CURSOR ON THE PTX ICON Placing the cursor on the PTX icon shown on the screen an information window containing the PTX Identifier position and status Overboard or Recovered appears User Manual 107 41943 334N 009 30 702E 1 0 359 TO CURSOR D Ve eam ites r i T e Id Time y 000001A0 10 16 79 PM V GH OH Dri Main A ions r hy P E x A e g 1 322 097 Pests Darema 3 Fig 5 11 4 Example of PTX information window 5 11 4 1 Deleting PTX The Delete PTX function permanently removes th
29. Points Of Interest On Off Off Off Off On Lat Lon Grid On Off Off Off Off On Chart Boundaries On Auto Off Off Off Auto Value Added Data On Off Off Off Off On Chart Lock On On On On On On Und Objects Limit 9999Mt 10Mt 10Mt 10Mt 10Mt 3Mt Rocks Icon Depth Icon Icon Icon Icon Icon Obstructions Icon Depth Icon Icon Icon Icon Icon Diffusers Icon Depth Icon Icon Icon Icon Icon Wrecks Icon Depth Icon Icon Icon Icon Icon Names On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Names ENTER Name Tags On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Name Tags ENTER Nav Aids amp Light Sectors On Nav Aids amp Light Sectors are shown Off Nav Aids amp Light Sectors are not shown No Sector Nav Aids are shown Light Sectors are hidden The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Nav Aids amp Light Sectors ENTER Attention Areas On Off The default setting is On The Attention Areas will always be contour only when On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Attention Areas ENTER Tides amp Currents On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Tides amp Currents ENTER 46 User Manual Seabed
30. RESET PARTIAL AND TOTAL TRIP Resets the partial or total distance travelled by the ship from the first activation of the chart plotter or starting from the values reset The partial or total trip value is shown on the top of the Navigation Data page gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER RESET PARTIAL TRIP ENTER gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER RESET TOTAL TRIP ENTER 5 4 COMPASS The Compass menu sets the desired value for Bearing and Magnetic Variation and selects the Calibration page gt MENU ADVANCED SETTINGS ENTER COMPASS ENTER User Manual 5 4 1 BEARINGS Selects either degrees Auto Magnetic or True If magnetic readings are selected the variation is computed automatically for every zone as soon as the chart is displayed The default setting is Mag gt MENU ADVANCED SETTINGS ENTER COMPASS ENTER BEARINGS ENTER 5 4 2 VARIATION It is possible to calculate the Magnetic Variation in an Automatic or manual mode by inserting the step for calculation of Magnetic Variation The default setting is Auto gt MENU ADVANCED SETTINGS ENTER COMPASS ENTER VARI ATION ENTER 5 4 3 CALIBRATION The variation table is used to match magnetic value readout on the chart plotter comparable with the value given by the compass of the boat In other words since the compass of the
31. Terms This section explains the terms that may be unfamiliar to the reader E Advanced Mode The chart plotter can operate in two different modes Basic Mode and Advanced Mode In Advanced Mode it is possible to have mote available functions for example it is possible to handle Waypoints E AIS Automatic Identification System It has been introduced to improve the safety of navigation by assisting in the efficient operation of ship to ship ship reporting and VTS applications E Altitude Altitude of GPS Antenna on the medium sea level E Arrival Time The estimated time of day you will reach your destination based on your current speed and track from GPS E Attention Areas Attention Areas are areas in which special attention by the mariner is required because of natural or man made hazards or sailing regulations and restrictions Moreover a special symbol I is placed inside the area selecting On option This is valid also for the categories FISHING FACILITY MARINE FARM CUL TURE MILITARY PRACTICE AREA RESTRICTED AREA SEAPLANE LANDING AREA When the area is small it is identified only by the boundary E Azimuth The angular measurement from the horizon to a satellite or another object E Basic Mode The chart plotter can operate in two different modes Basic Mode and Advanced Mode In the first mode thete is a restricted number of functions and it is not possible to handle Waypoints Marks Events and A B C D function E B
32. Tree s items The upper side of the page contains the Info Tree and the Lower side contains the expanded information While moving the cursor through the Info Tree all the relevant information of the selected object is shown on the lower part of the page When the selected object is a Tide Height pressing ENTER the Tide page is shown Pressing CLEAR the page is closed 3 5 4 INFO FUNCTION Place the cursor in any place you want and press gt MENU INFO to show the Info Tree and Expanded Info page see Par 3 5 4 SC ee Manual 3 5 5 GETTING PORT INFO Upon viewing the chart of a port ot harbour you will see a Port Info icon that can be clicked on to quety the available information immediately displayed with many details The Port Info icon is visible only if the Ports amp Services option is On default setting Port Info icon amp POSITION 42 54 186N 008 19 311E SOG Kts COG M 000 DST Nm BRG M 066 MAP DATUM WGS 1984 SCALE H H 8 26Nm Fig 3 5 5 Port Info icon The available information is shown in the Automatic Info window where icons of the available services are shown OBJECT LIVORNO C P 0 BEPPE CROCE LIVO POSITION HEER SE EEE TE Er ela 4a ETY To cursor BEER Seeger SS MAP DATUM WGS 1984 SCALE tt d 8 Z Nm Fig 3 5 5a Automatic Info window To expand information about that object press ENTER
33. alarm mes sages full quick info list of objects found by find nearest function and on charts such as place s names buoy s names and so on The default setting is Italian To select the language you want gt MENU BASIC SETTINGS ENTER LANGUAGE ENTER Choose the language you prefer and press ENTER to confirm Note If the selected language is not available on cartographic data English language is used instead MM User Manual WARNING II gt gt Tf you have accidentally selected an incomprehensible language and you don t be able to reselect your language the above procedure is not of help to you follow this procedure press MENU move the cursor to highlight the third selection starting from the top which corresponds to the Basic Settings menu and press ENTER Then a window appears with Language message press ENTER now select your language and press ENTER again Anyway if you in trouble see Chapter System Test fora RAM Clear operation the chart plotter will also return all selections in particular language to original default values 2 4 EXTERNAL CONNECTIONS 2 4 1 GPS CONNECTIONS Connects the GPS to the GPS serial Port 3 D EN D SP ANTENNA SMART GPS SENSOR 7 GPS SENSOR CABLE PIN WIRE COLOR FUNCTION O 1 RED POWER OUTPUT EVER DUTPUT GOSS v g 35 Vdc 2 GREEN GPS RX 3 BROWN GPS TX 6_ BLACK YELLOW SHIELD GND COMMON Fig 2 4 1 GP
34. amp Routes 15 46 47 125 TN 126 True Type Font penn 40 TIG rsisi 39 62 85 126 Turbo Zoom vrevvnrnevvnvevvnnnvvsnevrsveere 15 41 T daa ee 126 131 TOM E re 22 VRV 74 126 TU Na 22 EE ER ET NE 36 TWA ped chccasios ce secede siceceomsesaduesceaecanee cece 33 KO EE 33 W Type of Data EE 101 WAAG ees 36 126 Typical Connections ne 112 Waypoint 60 61 63 65 67 68 88 92 126 U Waypoint placing ssssseseesesseesesersreeen 60 Under ZOOM EEN 44 EE 36 Underwater Objects Limit 15 46 48 Weather Forecast nsseneneeeeeeeeeene 101 Units Selection rarrrrrrnrnrrnrnnnnnnnnnnnn 34 TE EN 17 User C CARD 17 26 78 80 100 118 WGS 1984 vasene de 90 126 User Point 14 34 65 66 72 74 126 Wind Data Page rrrrrrvvrnrrrrrrnnrnnnn 21 33 User Points Det 65 72 74 World Background Charts 05 116 BR LE E 87 126 worldwide background 40 VIN uer 15 90 126 WPL enter en nee ne ee ae 67 Wrecks sassone 15 16 46 48 55 V VAD E 126 X Value Added Data 15 46 48 126 ME eE 2 eecenceteneceeeee 36 126 TU 16 XTE Alarm ere 17 PP 32 ET EEE 17 Z VHF radio 2 sosescsintevarisvcuvnedenccensnoesnacenss 102 F ee EE 41 44 Video Input sanert 17 ZOOM IN WE 20 43 Video er EE 17 ZOO OU aseri rana 20 43 IVI Ga EE 126 ZTV PPs 15 42 Voice Mode uuinesnesnnedsajenoriamnain 37 ZOOMA EE 126 do Lee JE NERE 22 ZF Oen 126 132 CU se Manual
35. continuously sent to the Slave until the navigation is active If the Master is Navigating to a Single Destination the Slave will show the Destination position and acti vate the navigation to it If the Master is navigating to a Route the Slave will show the Route Leg composed by the Destination and the Waypoint after the Destination Next Waypoint and activate the navigation to it Any variation to the current C Link Navigation Data will be transferred from the Master to the Slave The Slave will be provided with a few dedicated pages to show the C Link Navigation Data received from the Master 4 8 1 OPERATIONS 4 8 1 1 Introductive elements It is important remark once more that this function does not transfer the whole Route but just the information relative to the navigation Such information will be removed from the Slave chart plotter as soon as the navigation is terminated C Link Navigation Data is exchanged by using two NMEA 0183 C MAP proprietary sentences PCMPN 1 and PCMPN 2 When the navigation is activated on the Master it starts outputting the C Link Navigation Data If the Slave 1s connected all C Link Navigation Data received ate stored in its memory and the navigation is started The information sent by the Master consists of the following values Navigation mode to Single Destination to a Route Route Name Destination ID User Manual Destination Position Next Waypoint ID Range from Destination to next Waypo
36. disables Off or insert the time 2 5 10 15 minutes for the Navi gation Voice mode If it is On the message is always sent as fast as possible Instead if it is one among the available values for example 2 minutes the message is sent related to the selected time in the previous example every two minutes gt MENU BASIC SETTINGS ENTER C VOICE ENTER NAVIGATION ENTER 3 2 9 2 Echosounder Enables On or disables Off the Echosounder Voice mode If it is On the Depth message is spoken The message is spoken if a valid depth data is received by the chart plotter or if it 1s in Simulation mode The default setting is Off User Manual 37 gt MENU BASIC SETTINGS ENTER C VOICE ENTER ECHOSOUNDER ENTER 3 2 9 3 Output Port Selects the Output Port for the Voice function The default setting is Port 1 gt MENU BASIC SETTINGS ENTER C VOICE ENTER OUTPUT PORT ENTER 3 3 A B C D FUNCTION The A B C D function allows you to create the B C D points and to delete them 3 3 1 INSERTING THE A B C D POINTS Place the cursor on the desired position and press ENTERon MAGNUM Pro ot A B C D on MAGNUM P vs on the screen the A point and an information window on A appear Move the cursor and press ENTER on MAGNUM Pro or A B C D on MAGNUM Prus again the B point appears connected to A with a straight segment an information window on A B segment distance
37. from NMEA Input port gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER RECEIVE 4 1 2 ROUTES The following functions are used for the route management The chart plotter handles routes from 1 20 which are permanently stored in the memory as they are created Only one route can be selected for work at any one time 4 1 2 1 Selecting route gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER CURRENT ROUTE ENTER A window appears with the route number list and the related route name Use the cursor key to scroll the list up down Pressing ENTER the selected route becames the current route Note If there is the Target in the current route it is not possible to change the current route So if the Current Route item is selected a Warning window appears because Target is placed in the current route 4 1 2 2 Route name gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE NAME ENTER Use the cursor key to insert the route name max 16 alphanumeric char 4 1 2 3 Deleting route gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER DELETE ROUTE ENTER lb Use Manual A window is opened select YES and press ENTER to confirm select NO and press ENTER otherwise The route remains on the screen shaded until the screen is redrawn To delete route see also Par 4 1 1 4 and 4 1 2 4 4 1 2 4 Reversing route gt MENU
38. inserted in the slot the message USER C CARD is shown m C CARD Connector Indicates if there is a malfunction in the connector It is used only in production 6 7 4 SERIAL PORTS If you ate having problems teceiving data from the position finding instrument this test should help determine the problem E Change Parameters To change the parameters of the serial interface This menu allows to select the Port 1 2 3 the Baud Rate between 4800 or 9600 the Data Bits Word Length between 7 or 8 the Parity between even odd or none the Stop Bits between 1 or 2 Default settings are Port Port2 Baud Rate 4800 Data Bits 8 Parity none Stop Bits 1 E Input Data Display To allow the chart plotter to act as a computer terminal and display the incoming data exactly as it received If the data displayed on the screen is unrecognizable you may have selected the wrong input parameters for your particular receiver Check yout re ceiver manual to be sure that you have selected the proper interface format If the screen is blank you may have a broken connection and no data is being received Use ZOOM IN to stop or continue after pause data displaying ENTER to show data in hex or ASCH mode normal or small and CLEAR to exit 6 7 5 EXTERNAL ALARM To check if the External Alarm has been transmitted 6 7 6 DISPLAY SETTINGS To select the display resolution E Resolution Sets the resolution among 1024x768 800x6
39. page A pop up screen advises the user that a Distress Call has been received Within the pop up screen it asks the user if he would like to view the call on the Chart page or exit the pop up screen By selecting the item VIEW ON CHART and press ENTER two options ate shown GoTo Vessel Activates the navigation to the Distress Call or Position Request icon The chart plotter changes the map scale to allow showing the Distress Call or Position Re quest icon and the vessel s icon simultaneously on the screen The chart plotter then verifies if there are obstructions land or low water between the two positions If obstructions are found the chart plotter shows a pop up screen saying that the navigation to the Distress Call cannot be set automatically and the user must define a route to avoid the obstacles Stay on View Exits the pop up screen and remains on the selected map screen 102 CU see Manual 5 10 2 DSC MENU To select the DSC menu gt MENU DSC ENTER The DSC menu is shown on the screen the items are described in the following paragraphs 5 10 2 1 DSC LOG gt MENU DSC ENTER LOG ENTER Selecting Log shows the Distress Call Log page or Position Request Log page it depends which of the two was selected NAME MMS 0080457645 ROY 0023244524 BOBI EO EN os GLR ONE POSITION REQUEST Fig 5 10 2 1 Example of DSC Log page Press GO TO to set the navigation on the selected D
40. screen Fig 3 5 7 7a Nearest Lakes list Then choose the lake you want and press ENTER the Full Info page is shown 56 CS eer Manual 3 5 7 8 Finding Lakes By Name Selects the Lakes By Names function gt MENU FIND ENTER LAKES BY NAME ENTER Shows the list of all lakes stored on the C CARD in alphabetic ordet Pressing MENU to insert the Lake name 3 5 7 9 Finding Points Of Interest Searches for nearest Points Of Interest gt MENU FIND ENTER POINTS OF INTEREST ENTER A sub menu is opened to find different categories of Points Of Interest 3 6 MAN OVERBOARD MOB It is an important function useful in the case someone or something falls over board 3 6 1 INSERTING MOB Press ov MAGNUM Pius MOD and on MAGNUM Pro EVENT for 2 sec onds to place MOB symbol at ship s coordinates On the screen the MOB symbol and a window to advise that the MOB is activated appear press CLEAR to delete this window Data displayed in Text Area are related to MOB Placing the cursor on the MOB symbol an information window appears BU POSITION 43 44 252N en E MAP DATUM NGS 1984 H SCALE ee r Fig 3 6 1 Man Overboard D Note In the information window the bottom side ENTER for Options appears only if the Advanced Functions item in the Basic Settings menu is activated On User Manual 11711 DI 3 6 2 DELETING MOB Press ov MAGNUM Pru
41. the MOB is placed to delete MOB The key ONLY ON MAGNUM Pro In Basic Mode pressing EVENT places Event at ship s coordinates in Advanced Mode places deletes edits and moves Event Pressing EVENT for 2 seconds sets MOB Man Overboard Pressing EVENT for 2 seconds when the MOB is placed to delete MOB The ee key Pressing MENU selects the Functions Menu The kent key Place the cursor and press DEST to set Target The FAQ key onty on MAGNUM Pius Press A B C D to place the A B C D points at cursor coordinates MM Use Manual The 4N key ONLY ON MAGNUM Pro In Basic Mode pressing MARK places Mark at cursor coordinates in Advanced Mode places deletes edits and moves Mark The Ka FUNCTION key ONLY ON MAGNUM Pius This key can be customized to have a quick access to the main functions Press FUNCTION for 1 second allows setting the shortcut to one of the following functions WIND select Wind pages Map place Mark EVENT place Event WAYPOINT place Waypoint EBL VRM place EBL and VRM C WEATHER shows C Weather Forecast mode Press and release FUNCTION executes the function that was assigned Note The selections Mark Event Waypoint and EBL VRM are available even if Advanced Functions is Off The key ONLY ON MAGNUM Pro Pressing TRACK enables or disables the track storing The SC key If Radar is connected pressing RADAR selects the Radar Page and pressing RA
42. to North the map 1s shown with North upwards Head the map is shown with the ship s current heading upwards Course the map is displayed with the currently selected course leg upwards The default setting is North It is possible to select the resolution angle for the Map Orientation 3 5 1 4 Zoom Type gt MENU MAP SETTINGS ENTER Zoom Type ENTER This feature allows more expansions or compression of the chart scale while zoom ing in ot out Zoom Type has two options Standard default or Flexi Zoom When in Flexi Zoom mode a short ZOOM push causes a change of chart whilst a long ZOOM push press and hold causes a pop up window to be displayed on a corner of the screen ADC et Manual The window shows the current Zoom factor By pressing ZOOM IN ZOOM OUT the map is expanded or compressed according to the zoom factor selected The window is automatically closed it ZOOM is not pressed for 2 seconds and the selected zoom factor will be used at the next zoom in out 3 5 1 5 Fonts amp Symbols gt MENU MAP SETTINGS ENTER Fonts amp Symbols ENTER On MAX charts it is possible to set the size of all names and symbols drawn on the charts selecting between Normal size the regular characters size and Large size NORMAL size LARGE size WON Bay Needles Channel Ce d AN ig a N Fig 3 5 1 5 Example of Normal size on the left side and Large side on the right
43. view of the chart As the upper side of the map 1s more compressed than the lower side a wider map area is visible The perspective view allows showing mote chart information immediately ahead and around the cursor The default setting is Off User Manual 4 Fig 3 5 1 1 Perspective View 3 5 1 2 Palette gt MENU MAP SETTINGS ENTER Palette ENTER It is possible to set the palette used to enhance the visibility of the screen depending on the surrounding light condition The possible choices are Normal Classic NOAA Night and Sunlight Normal is recommended when the chart plotter is not exposed to the direct sunlight When this mode is set the maps are displayed in order to use colors as similar as possible to the ones used in the original paper charts Classic uses mote vivid colors it is the default setting Night is recommended when the environment is dark in order to reduce the glare of the display The chart plotter displays maps and screen in darker colors Sunlight is designed to enhance the visibility of the screen when the chart plotter is exposed to the sunlight The maps are much brighter than in the other modes and the depth areas ate filled with white color so different depth areas are not easily distinguishable NOAA allows setting NOAA paper chart colors presentation 3 5 1 3 Map Orientation gt MENU MAP SETTINGS ENTER Map Orientation ENTER Selects the orientation of your chart according
44. 00 640x480 default 118 CU see Manual E Horizontal Size Allows entering the actual horizontal size of the screen The value can be entered either in centimeters or inches the default is 30 5 cm The unit of measure is user selectable see Screen Size Unit option If the unit of measure is changed the value is converted E Screen Size Unit Allows entering the screen size unit among cm and inch Centimeters is the default unit E Apply settings Sets the values Resolution and Horizontal size When this function is executed the fol lowing message ate shown The Display settings will be applied after power off Do you want to restart the unit now If the display will not be visible shut off the chart plotter again then power it up keeping pressed ZOOM IN to set default resolution 640x480 Choosing YES the chart plotter will be restarted and the new settings applied Choosing NO the new settings will be applied only next time the chart plotter 1s powered up Choosing ABORT will discarded all changes and nothing will be applied The original values of Resolution and Horizontal Size are restored and displayed Note It is possible to restore the lowest screen resolution 640x480 by pressing and holding ZOOM IN while the chart plotter is switched to ON This is useful when the image is not shown on the screen for example as effect of changing the display or display not compatible with the set resolution User Manual 119
45. 3 357 FANN 55 3 5 7 1 Finding Port Services E 55 3 5 7 2 Finding Tide Stations E 55 De AT ee E 55 357 4 Finding OSTEN GE 55 9515 PINGING POM BY TEE 55 3 5 7 6 Finding Port BY Distance Laursen enninnd 56 User Manual User Manual 3 5 7 7 Finding Lakes IESSE gtegegges tegerbeg ege ggeegdregesge 56 3 5 7 8 Finding Lakes By Name siruesiescxossnscheduprecnnietemiciecasneate 57 3 5 7 9 Finding PONS OF NESS 2 vsesanpe menne Bi 3 6 MAN OVERBOARD MOB ee Sr TNB eegene Eege S 36 2 Deleting MOB EE 58 For th Experienced Eet 59 4 1 MORE ABOUT CREATING AND USING ROUTES ees 59 Gu Ne Un GE 59 4 1 1 1 Adding Waypoint EE 59 TE NNN 60 4 1 1 3 Deleting Waypoint ceinsestnnssindusepencnesvndOnisepdtedentdeadetecasustiane 60 4 1 1 4 Deleting FOULS seaman 61 4 1 1 5 Distance and Bearing to Target Anke 61 MUS GO ERE 62 Deleting DR E re EE 62 4 1 1 6 Moving Waypoint E 62 4 1 1 7 NE MH EE 63 4 1 1 8 Editing Waypoint EE 64 4 1 1 9 Finding info on Waypoints User Points List page 65 Finding User Points snsadeisrcuduesyaxdessvenstnateasniceedersenmereeer 65 Deleting selected User Point rrnnnnnnnnnonnonvvnvnnnnnnnnvnnnn 65 Deleting all User Points with the same symbol 65 Deleting all User Points with the same type 65 Deleting all stored User Points rrrnnnnnnnonnvrnvrnnrnnnnnnn 66 Send Receive User Points cccccccccceeeeeeeseeeeeeseees 66 e EE 66 4 1 2 1 Seetmgro e uarvaassu
46. 3 2 DELETING EBL amp VRM gt Select Advanced Mode Place cursor on the cross EBL amp VRM ENTER Select DELETE and press ENTER the line and circle disappear from the screen 4 3 3 EDITING EBL amp VRM Select Advanced Mode Place cursor on the cross EBL amp VRM ENTER Select EDIT and press ENTER with the cursor key move the line and the circle when the desired position is selected press ENTER A window is shown containing the bearing value for the EBL and the radius value for the VRM 4 4 MORE ABOUT A B C D FUNCTION The A B C D function explained tn the previous paragraph 3 2 if Advanced Mode is selected allows you not only to create the A B C D points and to delete them but also to modify and move them 4 4 1 INSERTING THE A B C D POINTS Place the cursor on the desired position and oxn MAGNUM Pro press ENTER on the screen the Create window appears by using the cursor key select A B C D and press ENTER on MAGNUM Prus press A B C D The A point and an information window on A appear Move the cursor and ov MAGNUM Pro press ENTER select A B C D and press ENTER again on MAGNUM Pus press A B C D the B point appears connected to with a straight segment an information window on A B segment distance DST bearing BRG and total distance from the first point appears Moving the cursor following the above procedure the C and D points are placed see previous Fig SR User Man
47. 72 information ON route rrrrnrrrvvrnrrnnnnrrr 67 information on Waypoint rerrrnnnnnnnnnne 65 Inserting C CARD vussmnaiuanmivanseesn 26 Inserting MOB EE 57 Inserting the A B C D points 38 75 76 Inserting Waypoint snnnnnnnnnnnnnnnnnnne 63 Interface EEE 17 ISO Certification rrnnnnnnnnnnnnnnnnnnnr 40 K JO EE incaensuens 18 Keyboard s rie geg edd gg 17 19 keyboard brightness urrrrvnvvrvvvvvnnnnn 19 L LAKES rrrrnnrnrrrrrrrrvvrvererreserenrr 51 56 57 Lakes By Name mmmnnnnnnrnnnnnnnnnvrnnnn 16 57 Lakes jmo 16 51 56 Land Elevation Values 15 46 47 Land Elevations 15 40 46 47 language EE 22 49 LAT LON EEE 123 Lat Lon Gd 15 46 47 Latitude rrrnrrorrrrrrrrvrvreverrrnonrornornnnnnn 123 EAN FINS ur 79 ei 123 ORIGINS a sisstiasiassvenieenmusescdteniatineivionsiens 123 MON gt AEE 123 BOSE TAJO EE 97 M Magnetic Deviation nnrnnrnnnnnnnnonnnnne 123 129 Magnetic Variation ornnnnnnnnnr 92 123 Man OverBoard sosesc 20 57 MAP Aer 21 Map DA sassanidene 15 MADE vaere 84 Map Orientation ernrnnnnnnrrr 15 42 91 Map Settings rrrrrnrnnrnnnnnnn 15 21 41 MARK EEE EE 21 Mark er 21 70 72 88 123 Master Chart Plotter AAA 82 VE 40 MEMNON v rre 17 78 MENU er 20 Mixing Levels AA 15 41 43 Vd 96 98 102 104 MER Gueeeneet nce are 17 20 57 83 107 Vue E E 16 105 123 Ve ECO KE 107 MOBILA
48. 9 Grounding Alarm Report sessteccesvedscasiesavenxsrewosinisinswoexenatercesereounencaee 94 SIMULATION EE 94 5 6 1 Activate EE E 94 OL e BEE 95 e HEN W 95 3604 Dateand WR H 95 Bee GUIS OF end 95 Ed CS RE 95 5 7 1 AS System Definitions wxtsucs voveverdnsereninadpartanaverianenadendsecseianeninedemens 96 EE EGNE Ns eebe Eegen 97 TL EN ee E e E E 97 5 7 2 2 Activation range EE 98 ME COPAAN E 98 5 7 2 4 PAN 98 dd TOPA Ne 98 5 726 VPA 98 5 7 3 To Set the Chart Plotter for Receiving AIS 98 5 7 4 Quick Info on AIS Target eebe Seege 98 E ET 99 C WEATHER SERVICE E 99 5 9 1 C Weather Service Menu cccccccceeceeceeeeeeeeeeeeeeenenensaeeneeeeees 100 10 5 9 1 1 Download EE 100 Select Country to Call aus een 100 SM E 100 Download E 100 5 9 1 2 Copy from User C CARD egesgeegeegeesd ege gees nevne 100 5 9 1 3 Weather Forecast Lavdereddese deed 101 5 9 1 4 Real Time View see E NEEEES ENEREEeEEEEENEEE EN ECR egen 101 59015 TV DC Ol DAIA verre 101 510 DSC eebe 101 5 10 1 Distress Call and Position Request cccccccscceeseeeeeeeeseaeeeneens 102 5 10 2 DSG Men 103 81021 DSG LOG Lureri 103 eier gt ENE NE 103 Delete 0 ceecceceeeeseesssaceeeeceeeeeeeeeeeeseeesesesseeseeseeaaeaeeees 103 Delete All cccccccccccccseeceeceeceeceeeesseeeseeesseseaseaeeeeeeees 103 Hide Show 103 Position Request Distress Call l enn 103 EE Ne 104 El 104 MU 104 Delete nnnnnnnenenennnnenennnnnnrnrnr
49. AM Clear To clear internal memory If the chart plotter exhibits unusual behaviour or appears to be malfunctioning it may be possible to correct the problem by clearing RAM This opera tion will erase all Marks Events Routes stored track plots and destinations It will also return all selections Input Data Format Autopilot selection etc to original default values To confirm to clear RAM press ENTER again but if at this time you do not wish to clear RAM press CLEAR 6 7 2 DIM MENU To select the preferred value for contrast and backlight E Contrast Each time you ptessed the cursor key to right the screen will decrease brightness in stead of to left it will increase brightness E Backlight To set the backlight Operates in similar mode as Contrast 6 7 3 CARTRIDGES To check the C CARD and its connector E Background ROM To test the WorldWideBackground If there is not a malfunction the code of the Back ground and the message OK are shown m C CARD Test To test the C CARD There are the possible situations 1 it there is a C CARD inserted in the slot and there is not a malfunction the name of User Manual 117 the C CARD zone and the message OK ate shown 2 if there is a C CARD inserted in the slot but it is a damaged C CARD the name of the C CARD zone and the message Faulty are shown 3 if there is not any C CARD inserted in the slot the message not present is shown 4 if there is an User C CARD
50. COMMON WIRE COLOR FUNCTION POWER INPUT 10 35 ee POWER OUTPUT 10 35 Vdc INPUT 1 GPS RX OUTPUT 1 GPS on Port 1 12 CS ee Manual SMART GPS SENSOR GPS SENSOR CABLE PWR GND COMMON POWER OUTPUT 10 35 Vdc POWER INPUT 10 35 Vdc GPS RX OUTPUT 2 GPS TX INPUT 2 GPS on Port 2 GPS SENSOR CABLE pg ER WIRE COLOR FUNCTION mn POWER OUTPUT 10 35 Vdc GPS RX GPS TX BLACK YELLOW SHIELD GND COMMON GPS ANTENNA GPS on Port 3 6 4 2 AUTOPILOT CONNECTIONS POWER SUPPLY POWER amp I O CABLE PIN WIRE COLOR FUNCTION __ PWR GND COMMON POWER INPUT 10 35 Vdc INPUT 1 AUTOPILOT COMMON OUTPUT 1 COMMON Autopilot on Port 1 POWER amp I O CABLE PIN WIRE COLOR FUNCTION __ PWR GND COMMON COMMON OUTPUT 2 RX INPUT 2 Autopilot on Port 2 User Manual 113 6 4 3 EXTERNAL NMEA CONNECTIONS POWER amp I O CABLE PIN WIRE COLOR FUNCTION EEN EXTERNAL 1 PWR GND COMMON POWER INPUT 10 35 Vdc NMEA INPUT 1 DEVICE COMMON OUTPUT 1 EXTERNAL COMMON PWR GND COMMON NMEA POWER INPUT 10 35 Vdc DEVICE External NMEA on Port 2 6 4 4 C COM CONNECTION PIN CABLE COLOR FUNCTION PWR GND COMMON PWR 10 35 Vdc Used by C COM Used by C COM OUTPUT 2 Used by C COM INPUT 2 OUTPUT EXTERNAL ALAR
51. DAR fot 1 second selects the Radar menu The mar key Pressing MAD selects the desired map page and pressing MAD for 1 second selects the Functions menu The Ze key If Fish Finder is connected pressing ECHO selects the Fish Finder Page and pressing ECHO for 1 second selects the Fish Finder menu The act key Pressing PAGE selects the page you want User Manual CD 2 2 TURNING THE CHART PLOTTER ON AND OFF Before powering On the chart plotter check for the correct voltage 10 35 volt dc and the correct connections with the positioning instrument POWER amp I O CONNECTOR CABLE WIRE COLOR BLACK GND COMMON Fig 2 2 Power On 2 2 1 TURNING ON Press and hold the tight side of POWER for 1 second The chart plotter emits one rapid beep sound and a title page is opened After a few seconds the first of the two Caution Notice pages is displayed remind ing you that the chart plotter is only an aid to navigation and should be used with appropri ate prudence The electronic charts are not intended to substitute for the official charts Then the cartographic screen is displayed 2 2 2 TURNING OFF Press the right side of POWER and hold for 3 seconds a countdown timer ap pears on the screen if you release the key before the countdown timer reaches zero the chart plotter will remain On 2 3 SELECTING THE USER INTERFACE LANGUAGE It is possible to set the language to display menus data pages warning
52. DELETE DELETE ALL Fig 5 10 2 2 Example of DSC Directory page Edit gt MENU DSC ENTER DIRECTORY ENTER EDIT ENTER Edit the fields of any existing entry in the Directory Vessel Name MMSI number contact and phone numbet Add gt MENU DSC ENTER DIRECTORY ENTER ADD ENTER Add a new entry to the Directory Delete gt MENU DSC ENTER DIRECTORY ENTER DELETE ENTER Delete the selected entry Delete All gt MENU DSC ENTER DIRECTORY ENTER DELETE ALL ENTER Deletes all entries in the page 104 CS se Manual 5 10 3 QUICK INFO ON DSC ICONS Placing the cursor on the Distress Call or Position Request icon the following information is displayed Vessel Name MMSI Number Position Date and Time Distance and Bearing from current vessel s position Pressing ENTER it is possible by selecting DELETE deletes the DSC icon from the DSC Log page otherwise by selecting DSC LOG the DSC Log page ts shown 5 11 MOBILARM SYSTEM The MOBILARM is an automated crew monitoring system dedicated to monitor ing onboard crew by maintaining a constant link between the crew member and the boat The instant a man overboard event happens an automatic alarm is sounded and the vessels position is logged Connect the MOBILARM System to a serial port of the chart plotter 5 11 1 SOFTWARE SETUP After connections have been made the chart plot
53. DST beating BRG and total distance from the first point appears Moving the cursor and pressing ENTER on MAGNUM Pro ot A B C D on MAGNUM Paus places the C and D points Ess onaco PFTT TT EE POSITION 43 01 953N 008907 970E SOG Kts COG M c D S Jm y RG v EDRI BRG 215 M AEE MAP DATUM SCALE 26Nm Fig 3 3 1 A B C D points 3 3 2 DELETING THE A B C D POINTS Place the cursor on the desired point A B C or D and press CLEAR the point is deleted When the point is deleted the cursor is placed on the previous point if existed The labels of the next points are renamed W 0 User Manual 3 3 3 NAVIGATING ON THE A B C D POINTS If fix received is good place the cursor on the desired point A B C or D and press DEST When the ship arrives to the Destination point navigation follows to the next point if existed 3 4 NAVIGATING TO A SINGLE DESTINATION 3 4 1 DISTANCE AND BEARING TO TARGET Once you have positioned the cursor on your desired location a generic point on the map press DEST POSITION 43 01 984N 008 07 970E mm e T menn SOG Kts COG DST Nm BRG M E MAP DATUM Distance to Target Bearing to Target SCALE Z Nm Fig 3 4 1 Navigation to a single destination On the screen is shown a straight line connecting the Target called DEST with the ship s position and an information window with Target position
54. E gt MENU ADVANCED SETTINGS ENTER USER C CARD ENTER LOAD ENTER Before pressing ENTER choose file name in the list shown on the screen using the cursor key User Manual TY 4 6 3 DELETING FILE gt MENU ADVANCED SETTINGS ENTER USER C CARD ENTER DELETE ENTER warning window is shown select YES and press ENTER to confirm deletion select NO otherwise This operation remove old or unnecessary files to clean up your User C CARD Remember that this option permanently erases the file 4 6 4 FORMATTING USER C CARD gt MENU ADVANCED SETTINGS ENTER USER C CARD ENTER FORMAT ENTER A warning window is shown select YES and press ENTER to confirm the formatting select NO otherwise The format of User C CARD must be done before using a new User C CARD this operation prepares the User C CARD to receive and store information 4 6 5 CHANGING USER C CARD gt MENU ADVANCED SETTINGS ENTER USER C CARD ENTER CHANGE ENTER Allows to change the User C CARD 4 7 C LINK C Link system 1s a feature which allows to sharing the same cartographic data between two chart plotter units linked via serial I O port In order to activate C Link function a MAX data C CARD called REGULAR C CARD must be inserted into one of the two chart plotters and a special MAX data C CARD called MIRROR C CARD must be inserted on the ot
55. ENTER The C Map Weather Service menu 1s shown on the screen the items are described in the following paragraphs 5 9 1 1 Download gt MENU C WEATHER SERVICE ENTER DOWNLOAD ENTER Allows to connect the software to the Jeppesen Marine weather server and to download weather data directly via C COM Select Country to Call Allows the selection of the country to call The whole telephone number set is automati cally updated after every download SIM PIN Allows inserting of the PIN of the SIM Download Area Allows the weather download a squared grey area where the weather data will be downloaded is centered on cursor position See the following picture Area of coverage of downloaded data is located by default with its centre on the cursor position Cursor is locked to the gray area Moving the cursor also moves the gray area allowing locating it over the area where the user wants to download the Meteo forecast Indicates the LAT LON position of the cursor Fig 5 9 1 1 Download Area Press ENTER to activate the C Weather Download the whole data package see the previous Weather data package table are downloaded CLEAR allows to inter rupt the data download At the end of the operation press CLEAR to close the window 5 9 1 2 Copy from User C CARD gt MENU C WEATHER SERVICE ENTER COPY FROM USER C CARD ENTER Allows the C Weather Data loading from the User C CARD
56. GPS receiver connected to or integrated in the chart plotter so that the chart plotter converts the position received from the GPS to the Map Datum currently selected m the menu in order to match the position from the GPS with the position on the charts You must know what datum reference is used by the GPS and set it in the Fix Datum option WGS 1984 is the default Fix Datum M User Manual gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER FIX DATUM ENTER 5 3 3 MAP DATUM Allows selecting any Geodetic Datum reference from the over 100 available on the chart plotter Map Datum selection switches to the selected reference datum applying the datum offsets stored with the charts WGS 1984 is the default Map Datum gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER MAP DATUM ENTER 5 3 4 ORIENTATION RESOLUTION Selects the orientation of your chart according to your personal needs see Par 3 5 1 3 for more information The Orientation Resolution is the resolution angle for the Map Orientation range 5 60 The default setting is 10 gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER ORIENT RESOLUTION ENTER 5 3 5 ROLL ROAD SCALE Sets you preferred Rolling Road Scale among 0 2 0 5 1 0 2 0 4 0 10 0 The default setting Is 0 2 gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER ROLL ROAD SCALE ENTER 5 3 6
57. H Always uses English e LOCAL Uses the first Local language present on data If no Local language is available English is used instead gt MENU MAP SETTINGS ENTER Chart Language ENTER Mode ENTER Note a When User Interface Language is changed Chart Language settings are set as follows MODE ze set to Off and Chart Language is set as the User Interface Language selection if available on the chart data otherwise is set to English D Ifthe cartographic data is changed for example the C CARD is removed or replaced Chart Language settings should be verified and if necessary changed 3 5 2 GETTING AUTOMATIC INFO The type of Automatic Info is user selectable gt MENU ADVANCED SETTINGS ENTER SETUP ENTER AUTO INFO ENTER The possible settings are Off disabled no automatic info shown at all On Points only on points This is the default setting On All on all objects points lines and areas The Automatic Info On Points shows information when the cursor is placed on points as Port Services Tides lights wrecks rocks buoys beacons obstructions land markers etc The Automatic Info On All shows information when the cursor is placed on points on lines as Depth contours Traffic Separation Territorial Sea Cartographic Lines etc on ateas Depth Built up Sea Attention Restricted etc and on names on the beginning of the text hot spot or on any of t
58. HDG Off gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 1 2 3 4 5 NMEA OUTPUT ENTER 3 2 8 4 GPS Setup Menu It is possible to set the your preferred configuration for the connected GPS gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER GPS SETUP ENTER Note This item is shown alternately to the selection of the output messages when to the related port is connected a GPS identificable by the chart plotter Restart GPS Restarts all GPS processes Once executed the message Done is shown gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER GPS SETUP ENTER RESTART GPS ENTER Differential Correction Source Allows setting what kind of Differential Correction will be used by the GPS between WAAS EGNOS and RTCM beacon correction The default setting is WAAS EGNOS gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER GPS SETUP ENTER DIFF CORRECTION SOURCE ENTER Navigation Speed Allows setting the Navigation Speed among Low Speed Medium Speed and High Speed gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER GPS SETUP ENTER NAVIGATION SPEED ENTER 3 2 8 5 Send amp Receive Marks Routes Sets the desired port used for transferring User Points and Routes functions gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER SEND REC ROUTES amp MARKS ENTER Por
59. INGS ENTER Other Map Configurations ENTER Obstructions ENTER Diffusers Off Icon Icont Depth The default setting is Icon gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Diffusers ENTER Wrecks Off Icon Icon Depth The default setting is Icon gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Wrecks ENTER Note Choose the option SOF the object is not visible independently of the selected Underwater Object Depth Value e ICON the object icon is visible without tags in the range selected from Underwater Object Depth Value option e ICON DEPTH the object icon and tag is visible in the range selected from Underwater Object Depth Value option 48 User Manual 3 5 1 12 Selecting the Cuart Language gt MENU MAP SETTINGS ENTER Chart Language ENTER The possible choices ate Language Allows setting the language to display chart information The language is chosen among the list of languages available on the cartographic data C CARD or embedded charts gt MENU MAP SETTINGS ENTER Chart Language ENTER Lan guage ENTER Mode Defines how objects are translated It is possible to choose between the three following options OFF Uses the same Language used for LANGUAGE If the selected language is not present on the objects information English is used instead ENGLIS
60. KEE D MAP DATUM apraia WGS 1984 Fig 4 1 1 8 Edit Waypoint 1 Use the cursor key to select the field If you have selected Name field press ENTER use the cursor key to insert the character 8 characters max then press ENTER If Symbol field is selected press ENTER a window with 16 different symbols appears Secche Di IA WII 7 ze POSITION 43 09 014N mm mm mm mm mm mm 1 EE E SOG Kts COG M KE Cum x GL DST Nm BRG M l MAP DATUM apraia MAP DATUM l WGS 1984 N 6 V LIDTOGZ Fig 4 1 1 8a Edit Waypoint II Waypoint symbols 4 CS ee Manual Use the cursor key to select the symbol and press ENTER If select Coordinates field press ENTER and then use the cursor key to insert the value Then press CLEAR If Color field is selected press ENTER a window with 8 different colors appears use the cursor key to select the desired color and press ENTER POSITION Ch 43 09 033N 009 53 757E T S0G Kts COG M im KOTY b WPTEe6 N Gs Fig 4 1 1 8b Edit Waypoint III 4 1 1 9 Finding information on Waypoints User Points List page gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER Move up down the cursor key to select the User Point you wish If the page con tains more than 8 User Points the list continues in the next pages Finding User Points gt MENU ADVANCED SETTINGS ENTER USER
61. LE LORENZ MARINE ELECTRONICS One Touch To Choose Your World MAGNUM PRO CODE S3egLZctcmp Oww 1602g970 A01 160709 MAGNUM PLUS CODE S3egLZctcms Oww 1602g970 A01 160709 USER MANUAL Copyright 2009 LORENZ ELECTRONICS Italia All rights reserved Printed in Italy No part of this publication may be reproduced or distributed in any form or by any means or stored in a database or retrieval system without prior written permission of the publisher Warning Electronic charts displayed by the chart plotter are believed to be accurate and reliable but they are not intended to substitute for the official charts which should remain your main reference for all the matters related to the execution of a safe navigation For this reason we would like to remind you that you are required to carry on board and use the officially published and approved nautical charts Caution E Please read through this manual before the first operation If you have any questions please contact the Company customer service or your local dealer E The chart plotter is not built water proof Please give attention to avoid water intrusion into the chart plotter Water damage is not covered by the warranty E Extensive exposure to heat may result in damage to the chart plotter E Connection to the power source with reversed polarity will damage the chart plotter severely This damage may not be covered by the warranty E The chart plotter contains dang
62. LP ENTER Using ZOOM IN and ZOOM OUT select previous and next page respectly 6 6 3 IF YOU NEED ASSISTANCE The list above should allow you to solve most of the operating problems you ate likely to encounter Simply disconnecting the chart plotter from power for a moment may solve your problem as well If this does not help you can try one additional memory clear option This is a factory default RAM Clear that should only be tried after all other attempts have been made When using the RAM Clear feature you will loose all user stored information and the chart plotter will default to factory settings Before this step you have the option of saving uset Marks Track history and Routes to a User C CARD this is an optional purchase from User Manual YS your dealer To perform a RAM Clear see Par 6 6 1 If you still need assistance call your local dealer reporting the Software Release and Cartography information available in the About Page gt MENU About ENTER 6 6 3 1 World Background Charts The internal background charts can be updated to include the MAX A and B level charts which provide improved marine data rivers lakes terrestrial data major streets highways railways etc Nav Aids depth areas territorial water areas etc by reading them from a special data C CARDs contact your local dealer All units must have the WorldWide Background upload function that is activated from the system Worldwide
63. M 6 4 5 EXTERNAL ALARM CONNECTION POWER amp I O POWER SUPPLY POWER amp I O CONNECTOR CABLE PIR CABLE COLOR FUNCTION 1 BLACK PWR GND COMMON 2 RED PWR 10 35 Vdc 8 BLUE OUTPUT EXTERNAL ALARM Open Collector 1144 oSo User Manual 6 6 TROUBLESHOOTING The following is a brief guide to some of the problems you may experience while using the chart plotter with common solutions 6 6 1 PROBLEMS AND SOLUTIONS The chart plotter does not turn On Make sure that the correct voltage 10 35 volt de is present Check also that the polarity is correct Refer to the Par 2 2 The chart plotter does not turn Off If after a POWER pressure for at least 3 seconds the chart plotter does not turn Off then turn Off the voltage The chart plotter does not respond to any command Try to turn Off and then turn On If the problem persists erase the memory see Par 6 6 1 The chart plotter does not get a valid fix Make sure that no metal obstacle 1s placed around the chart plotter acting as a shield for the antenna If after 15 minutes the chart plotter does not get the fix turn it Off and On again The chart plotter screen becames very dark after a long exposure to direct sunlight Control the contrast see Par 2 3 6 6 2 QUICK REFERENCE GUIDE It is available an help on line to explain as the chart plotter works gt MENU HE
64. NG THE USER INTERFACE LANGUAGE rnnnorvvvverrrrnrnrnvvveen 22 2 4 EXTERNAL CONNECTIONS eegene 23 2 4 1 Een ee 23 2 4 2 Autopilot Connections EE 23 2 4 3 External NMEA Connections as cccsccieccerts nennseveiesesnsdicdeeicectrteseeencces 24 2 44 C COM Connections NEEN 25 2 4 5 External Alarm Connection ccccccccececeeseeeeeeeeeeeenenaneeeeeeeeeeees 25 2 5 ADDITIONAL C CARDS saus efa dende 26 2591 Inseting C CARD EE ARRS 26 2 5 2 Removing C CARD uLeraamestvasrsrsaamsemrnissensievi rei ne 27 26 MENU e age LEE 27 PAET eer eer etre eee er ere ew ere enn el eee trey een 27 POP UNGINGW USER sissioni EE 29 3 1 SCREEN DISPLAY CONFIGURATION ssecicscencdecincesecusireccecetexdendvoleentedees 29 3 1 1 Charts and Text EE 30 JE DN EE E 31 313 GPS ere PAGE anse eege dn 32 3 1 4 Navigation Data Page avvek 32 3 1 5 3D Navigation Data Page EE 33 316 Wina Data Page EE 33 3 2 BASIC SETTINGS E 33 Jed COURSE VENN EE 34 32 2 05 EE 0 ERE See 34 32 9 FANGET FUNCIONS sveaerne Dauuareinisdoccanees 34 121 VE PONISI 34 325 DOR NNN re 34 20 Units SUG EE 34 3 2 7 Nav Aids Presentation ansees Aden 35 328 Inp tOutput ET EE 35 3 3 3 4 3 5 3 2 8 1 Port 1 Port 2 Port 3 Port 4 Port 5 Input n se 35 3 2 8 2 Port 1 Port 2 Port 3 Port 4 Port 5 Output n se 36 3 2 8 3 Port 1 Port 2 Port 3 Port 4 Port 5 NMEA Output 36 Se GPS Setup MENU EE 36 Restan E 36 Differential Correction Source AAA 36 Navigation Speed EE 36 3 2 8 5 Send
65. NGS ENTER INPUT OUTPUT ENTER PORT 2 OUTPUT ENTER Then choose your preferred setting among the NMEA available settings NMEA 183 4800 N81 N NMEA 0180 NMEA 0180 CDX the default setting is NMEA 0183 4800 N81 N and press ENTER to confirm 2 4 3 EXTERNAL NMEA CONNECTIONS To connect the External NMEA to the serial Port 1 see the following picture R IS La POWER SUPPLY Be e t POWER amp I O POWER amp UO CABLE PIN WIRE COLOR FUNCTION COMNEN EXTERNAL 1 BLACK PWR GND COMMON 3 WHITE INPUT 1 Eo O O O O O O DEVICE 4 GREEN COMMON 6 YELLOW OUTPUT 1 Fig 2 4 3 External NMEA Connections on Port I To choose your preferted setting follow the procedure gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 1 INPUT ENTER Then choose your preferred setting among the NMEA available settings NMEA 1200 N81 N NMEA 4800 N81 N NMEA 4800 N82 N NMEA 9600 081 N NMEA 9600 N81 N the default setting is 4800 N81 N and press ENTER to confirm M User Manual To connect the External NMEA to the setial Port 2 see the following picture aN IS gt POWER SUPPLY o POWER amp I O POWER amp UO CABLE EXTERNAL PIN WIRE COLOR FUNCTION ___ COMMON NMEA 1 BLACK PWR GND COMMON 7 5 IGRAY OUTPUT 2 7 BROWN INPUT 2 Fig 2 4 3b External NMEA Connections on Port 2 To choose your pr
66. Over Zoom between chart levels resulting in optimal scale display for any situation Dynamic Elevation Data optimized palettes including the NOAA color palette Perspective View Real World perspective view of the chart updated real time during navigation Smooth Zoom smooth transition of cartographic levels Enhanced Turbo Zoom extra fast cartography level change displaying the most important cartographic objects Enhanced Mixing Levels seamless data presentation Off line redraw cartography level transition without image construction Cartographic Data related Features Guardian Alarm automatic control and alarm over obstacles on charts in front of your boat Safety Toolbar interactive alarm system for situational awareness on screen Safety Route Check sophisticated function checking dangerous objects along your navigation route MAX and NT NT C CARD coexistence When NT data and MAX data cover different areas the chart plotter gets data from both charts depending on the current position When NT data and MAX data cover the same area the chart plottet gets data only from MAX chatt 3 5 1 MAP SETTINGS MENU It is possible to select the Map Settings Menu following the procedure gt MENU MAP SETTINGS ENTER 3 5 1 1 3D View Perspective View gt MENU MAP SETTINGS ENTER 3D View ENTER Chart data may be projected in perspective mode during navigation This function allows setting the panoramic
67. POINTS ENTER FIND ENTER The chart plotter exits from the User Points List page and redraws the chart The selected point appears with the cursor placed on it Deleting selected User Point gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER CLR ONE ENTER Deletes the selected User Point A warning message appears select YES and press EN TER CLEAR otherwise Deleting all User Points with the same symbol gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER CLR SYM ENTER Deletes all User Points which have the same identifier of that shown in the selected row A warning message appears select YES and press ENTER CLEAR otherwise Deleting all User Points with the same type gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER CLR TYP ENTER User Manual 685 Deletes all User Points which have the same type of that shown in the selected row A warning message appears select YES and press ENTER CLEAR otherwise Deleting all stored User Points gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER CLR ALL ENTER warning message appears select YES and press ENTER CLEAR otherwise to delete all stored User Points Send Receive User Points Sends all User Points to an external device using the sertal port gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER SEND Reads all User Points
68. Partial Trip ans neste 16 Reset Total TAP nceaseivnisicesisenceeelpeneiaunseniat 16 DEET veer 118 Restart GPS Larsasnesenannus 36 Reversing route ceeeeeeeeeeeees 67 68 VL 36 RMB erd 36 RMG vane 36 Roads 15 40 46 47 ROCKS ou cc eecceeceeecseeeseeeeeeeseueeees 15 46 48 Rolling Road Scale vuassmminidine 16 91 rOUte oo eeeeeeeees 14 59 60 61 63 66 68 72 81 124 route check report ccccceeceeeseeeeeees 69 Route 610 0 Geteste 67 Route Data Hepnort nen 68 84 Route Name nnnnnnnnnrnnnnnrrnnnnnnnnnvrnvnnnnnn 66 Route planning sement 60 Route Report rrrnnnnrnnnnnrnnnnnnnnvnnn 67 69 PUG EEE 124 5 EEE 67 S Safe Route Check 14 41 69 Safety Status Bar rrrrrrvrrvonnrnenn 15 44 Safety Toolbar sicavecisaniataeusorunivontenimedsiers 41 Satellite image Coverage AN 15 Satellite Imagery snnnnnnrnvnvnnnnnre 15 45 SAVNO ae 79 0 EE 44 Screen Amplifier scscsccceeeeeees 34 Seabed Type cccccccseeseeeeeees 15 46 47 Search amp Find via cescksensccssoseeeeddeotensassinncts 40 selecting active Track AAA 77 Selecting distance track c000 78 Selecting route AE 66 68 Selecting time track rrrrrrrrrnrrnnrnnnn 78 Send amp Receive Marks Routes 36 Send Receive route rrrrrvrrrvvrrrrrrnnnnnnn 67 Send Receive User Points rrrvrrrnrnnn 66 Serial Porte 4 118 Setup MONA scivinnaiavauweisisavscornidendanimessnics 87
69. RM Status osson 105 MOdEM EE 25 Modem Test 2 eket rgbetdeessdeteedCV esegCgeg 118 Moving Mark EEE 71 Moving the A B C D poomts 76 Moving Waypoint saisnciiewnensueinananmsveutiensute 62 Multilanguage EE 15 40 N KE CC 15 46 Names rrrnnnnnnnnnnnnnnnnvnnnnnnevnnnnnnnnnnee 15 46 Natural Features aaaeeeaa 123 Nav Aids amp Light Sectors 15 46 Nav Aids Presentation 35 Ke E 19 72 Navigate mode arrnnnnnnnnnnnnnnnnnnnnnnnr 124 Navigate menu n se 90 Navigating on the A B C D points 39 Ke Elei 16 37 Navigation Data Page rnnnnnnnnnrr 32 91 Navigation mode errrrnnnnnrrrrnrnnnnnnnnnnnn 81 Navigation Speed E 36 Nearest Services rrrrrrrnrrrrrrnrrnnnnnnnnn 16 NMEA EE 24 NMEA output PO E 67 NMEA 018323 35 36 81 88 98 124 NO ere 35 42 NT NTH EE 40 O OPE EE 40 Obstructions 15 16 46 48 55 Off line redraw rrnnnnnnnnnnanornvnnvrnnnnvnnnnn 41 Official data source 40 opto isolated E 4 130 OSGB eege 15 90 124 Other Map Configurations 00 45 Dut PON s n 38 Over ZOOM EE 44 P ale e 14 E 29 Page PICVICW wecccvdrrsevirasuvcninsdweliepevesinses 29 Page Selection rrrrrarrrrnrnnnnnnnvnvvvnnnn 29 PA Las 15 42 POMPN ceccectstaneseaedsndeteedbsdandensedevtecedendes 81 Perspective View rrrrnrrrrnnnrrnnnvrre 15 41 Photos amp Diagrams errrrnnnrnnnnnrr 15 40 Picture Size guruen 50 Pictures
70. S Connection on Port 3 Control the input setting following the procedure gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 3 INPUT ENTER NMEA 4800 N81 N ENTER The GPS can be connected also to the Port 1 and 2 in this case select NMEA 0183 4800 N81 N on the used pott 2 4 2 AUTOPILOT CONNECTIONS To connect the Autopilot to the serial Port 1 see the following picture POWER SUPPLY POWER amp I O CABLE PIN WIRE COLOR FUNCTION __ POWER INPUT 10 35 Vdc INPUT 1 AUTOPILOT COMMON COMMON OUTPUT 1 Fig 2 4 2 Autopilot Connections on Port 1 To choose your preferred setting follow the procedure gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 1 OUTPUT ENTER Then choose your preferred setting among the NMEA available settings NMEA User Manual DY 0183 4800 N81 N NMEA 0180 NMEA 0180 CDX the default setting is NMEA 0183 4800 N81 N and press ENTER to confirm To connect the Autopilot to the serial Port 2 see the following picture POWER amp I O POWER amp I O CABLE PIN WIRE COLOR FUNCTION 1 BLACK PWR GND COMMON 2 RED POWER INPUT 10 35 vdo AUTOPILOT 5 GRAY OUTPUT 2 BA 7 BROWN INPUT 2 Fig 2 4 2a Autopilot Connections on Port 2 POWER SUPPLY To choose your preferred setting follow the procedure gt MENU BASIC SETTI
71. S is an Automatic Identification System It has been introduced to improve the safety of navigation by assisting in the efficient operation of ship to ship ship reporting and VTS applications The system should enable operators to obtain information from the ship automatically requiring a minimum of involvement of ship s personnel and should have a high level of availability AIS transponders installed on IMO vessels use VHF fre quencies to User Manual DS Transmit details of their own vessel Receive details from other vessels or navigation aids within VHF range Information being transmitted from vessels over 300 tons that due to recent world wide legislation are required to fit Class AT AIS transponders Connecting to the chart plotter an AIS receiver please contact your local dealer vessels with AIS transponder within VHF range are displayed on screen giving the skipper of navigator a visual interpretation of the data of nearby vessels This improves safety and specifically for collision avoidance reasons 5 7 1 96 AIS SYSTEM DEFINITIONS Target It is a vessel equipped with AIS Information about the targets is being received by AIS Receiver and displayed on the screen CPA Closest Point of Approach is the closest distance that will be achieved between your vessel and the tracked target based on yout vessel s speed and direction and the target s speed and direction CPA Limit This is the distance from your ve
72. SC point Other available functions ate Locate gt MENU DSC ENTER LOG ENTER LOCATE ENTER Centers the map on the selected DSC position Delete gt MENU DSC ENTER LOG ENTER DELETE ENTER Deletes selected DSC position Delete All gt MENU DSC ENTER LOG ENTER DELETE ALL ENTER Deletes all entries Hide Show gt MENU DSC ENTER LOG ENTER HIDE SHOW ENTER Allows hiding showing the selected DSC position on the chart display Position Request Distress Call gt MENU DSC ENTER LOG ENTER POSITION REQUEST DIS TRESS CALL ENTER User Manual 103 Shows Position Request Distress Call page When Position Request page is active this mes sage changes to Distress Call 5 10 2 2 DSC Directory gt MENU DSC ENTER DIRECTORY ENTER Selects the DSC Directory page From this page the user can assign the Vessel Name Contact Name and Phone number to any MMSI Maritime Mobile Service Identity so that when a DSC Distress Call or Position Request is received the name of the vessel is displayed in place of the MMSI number a unique number that is assigned to a DSC radio station for use in emergency situations VESSEL NAME MMSI CONTACT PHONE SCORPION 0046712433 ERICH SMITH 12372133456 STRIKE 99 0036612458 JIMMY PAGE 22832178345 JUPITER 0036612459 ROBERT PIO 22114433001 SARA 0063412123 SUSANNE 44332211001
73. Type On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Seabed Type ENTER Ports amp Services On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Ports amp Services ENTER Tracks amp Routes On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Tracks amp Routes ENTER Depth Range Min Sets a min reference depth value The default setting is 0Mt gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Depth Range Min ENTER Depth Range Max Sets a max reference depth value The default setting is 10 Mt gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Depth Range Max ENTER Land Elevations On Off The default setting is Off gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Land Elevations ENTER Land Elevation Values On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Land Elevation Values ENTER Roads On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Roads ENTER Points Of Interest On Off The default setting is On gt MENU MAP SETTINGS ENTER Other Map Configurations
74. User Manual n e 1 3 BASICS The chart plotter is controlled by using 14 keys There is also a cursor key to move a cursor across the screen s you press a key a single audio beep confirms the key action every time the key pressed is not valid three rapid beeps sound indicates that no response is available Fig 1 3a MAGNUM Plus 18 CU set Manual Before You Begin This chapter provides basic information to get you start using the chart plotter it will help you to become familiar with the chart display and the functions of the controls before you start using the chart plotter 2 1 THE KEYBOARD The C POWER key Press POWER down for 1 second to turn the chart plotter On Press and hold POWER down once the chart plotter has been turned On for 3 seconds turns the chart plotter Off Press and immediately release POWER to adjust the keyboard brightness The key Excluding specific situations returns to the previous menu or leaves a menu with out making changes If you are not into a menu if the GPS computing a valid fix position and the chart plotter is not in Home mode pressing CLEAR sets Home mode When Home called also Navigate mode 1s set the cursor is not shown anymore and all carto graphic functions zoom scroll etc are leaded by the fix position The fix is centered in the map display and the
75. VECTOR Disables Off the Course Vector or selects the preferred time among 2 10 30 Min 1 hour 2 hours Infinite The default setting is Infinite gt MENU BASIC SETTINGS ENTER COURSE VECTOR ENTER 3 2 2 SCREEN AMPLIFIER The Screen Amplifier function allows when it is On and Home mode is set to place map on the screen telated to the fix position and direction so the map shown is that before the ship The default setting is On gt MENU BASIC SETTINGS ENTER SCREEN AMPLIFIER ENTER 3 2 3 ADVANCED FUNCTIONS When it is On the chart plotter works in Advanced Mode otherwise when it is Off the chart plotter works in Basic Mode The default setting 1s Off gt MENU BASIC SETTINGS ENTER ADVANCED FUNCTIONS ENTER 3 2 4 USER POINTS Selects the User Point display among On Off or Icon The default setting is On gt MENU BASIC SETTINGS ENTER USER POINTS ENTER 3 2 5 DEPTH WINDOW Enables Disables the display on the Depth Window on the screen The default setting is Off gt MENU BASIC SETTINGS ENTER DEPTH WINDOW ENTER 3 2 6 UNITS SELECTION Allows to select the preferred unit for Distance Speed Depth and Altitude alti tude of GPS Antenna on the medium sea level Speed Kts knots Mph miles per hour Kph chilometres per hour The default setting is Kts gt MENU BASIC SETTINGS ENTER SPEED ENTER Distance
76. Window Cal Cal Zem or Ship Coordinates Distance and Bearing from Ship to Cursor from Ship to Target if Target is set from Ship to MOB if MOB is set Chart Scale The second is with text area on the bottom line of the screen with partial informa tion on SOG Cursor Coordinates J 43 01 765N g 008 22 970E DST 10 9 Nm BRG 090 M Distance and Bearing from Ship To Cursor from Ship to Target if Target is set from Ship to MOB i MOB is set Speed Over Ground Fig 3 1 1a Chart Data Window on bottom If Target is set in the previous Fig 3 1 1a instead of the only SOG information window a text line with DST BRG XTE SOG and TTG information appears Then it is possible to see on the screen only charts 30 User Manual EI E Ps Fe Fig 3 1 1b Chart full screen 3 1 2 DEPTH GRAPH The depth graph can be shown in two different modes Depth graph displayed only on 1 4 of the screen E CURSOR d 43 01 765N 008922 970E dch 10 9 090 000 D Fig 3 1 2 Chart Depth 1 4 ot Depth graph EE on 1 2 of the screen 43 01 765N 008 18 470E H 7 67 dr 090 Fig 3 1 2a Chart Depth 1 2 User Manual o y 4 1 3 GPS STATUS PAGE The GPS Status page shows in graphic mode GPS data iA Fix Status Used Satellite 44 03 576N
77. aypoint position Navigation time from the Waypoint and Bearing the previous one Leg Distance l Total Distance Distance between the es from the first Waypoint and the previous one eg SPEEDIG GKts FUEL 198 h REVERSE CLEAR aypoint of the route Fig 4 1 2 7 Route Data Report page Selecting route gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE REPORT ENTER ROUTE tt ENTER Use the cursor key to select the route number and press ENTER The route shown by straight segments is centered on the screen with the cursor on the central Waypoint See also Par 4 1 2 1 Note If there is the Target in the current route it is not possible to change the current route So if the Route H item is selected the chart plotter emits three beeps Changing Speed amp Fuel values gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE REPORT ENTER It is possible to modify the Speed and Fuel consumption values respectively by selecting SPEED and FUEL Insert value by using the cursor key and pressing ENTER Reversing route gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE REPORT ENTER REVERSE ENTER Reversing a route plan is most typically used to return to the point where the route originally started See also Par 4 1 2 3 Deleting route gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE REPORT ENTER CLEAR
78. boat must be compensated due to the iron masses we use the same values given by the chart plotter This means that for example if the BRG to the next Waypoint readout in the chart plotter display is X Mag degree if you steer the boat reading X Mag degree from the compass you ate driving well toward the next Waypoint gt MENU ADVANCED SETTINGS ENTER COMPASS ENTER CALI BRATION ENTER 5 5 ALARMS The chart plotter provides alarm settings for various functions Here you can set the system for your navigational requirements gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER 5 5 1 ARRIVAL ALARM Sets an acoustic alarm to sound when the vessel 1s approaching the destination The default setting is Off gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER AR RIVAL ALARM ENTER 2 User Manual 5 5 2 XTE ALARM Sets an acoustic alarm to sound when the vessel is deviating from a defined course The default setting is Off gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER XTE ALARM ENTER 5 5 3 ANCHOR ALARM This function allows inserting of the limit of anchor dragging beyond that the alarm is activated The chart plotter computes the distance between the current GPS posi tion and the GPS position saved at the activation of the anchor alarm in the menu If the computed distance exceeds the value set in the menu the chart plotter shows the alarm
79. ding User Point aaeeea 65 Finding e 16 55 Fish Ender 16 109 Fish Finder Dual Frequency 16 Fish Finder Full Screen rrrnnnnnnnnnnnne 16 Fish Finder Page cceee 21 109 Fish Finder Zoom egtegeegeugueegeiestesgekdereg 16 el e SE 15 Pe PWM EE 16 PIX FUNCIONS setescssseossccatceseuesdeeansacnessaded 15 FIX MENU EE eeni 88 lext Zoom 41 42 POMS Ge SYMONS scenscnsucseernscenteiess 15 43 Format User C CARD rrrrnnnnnnnnnnvnnnnnn 80 Eeer 68 Ul GA EE 31 Full Inio ees 50 51 FUNCION EE 21 Functions MENU gcegee eegen gees e ggokeg 20 G GGA onnnnissssnsesnrrrsseertrrrrrssrrrrrnnrseerren rnn 36 G EE EE 36 GO TO EE 39 71 73 103 Eege 71 73 123 Goto EE 108 GPS 19 23 32 36 88 90 112 123 GPS Connections errunvnvrvvnvevvnnr 20 112 GPS Data Page EE 32 GPS Setup MENU Lu namssvasmnesnespnis 36 GPS Status page eeben 32 Graphic Data Page sasansnnsene 33 39 Grounding Alar sausressmsssvssaevesevenensnnnr 17 User Manual Grounding Alarm Range aeeeeeeeaeeae 17 Grounding Alarm Report 0 0 eee 17 Guardian Alarm aeeoe 14 41 Guardian Technology Ak 93 H HDG EE EE 36 123 PDOP EE 32 123 HEAD steere 33 le ui aueoiraceeca E T 123 HOME seerunnnnnnvnnnnnnnvnnevnnennnensnne 19 20 123 Eeer 36 ener 17 HMO FUNCIO vanene 52 Info on E 51 Info on eier 50 aea Ke 52 information on Event rrnnnvrrnrnnrnnnnrrr 74 information on Mark ccccccccssseeeeeeeees
80. e CPA and TCPA values Note The selected AIS target icon is surrounded by a square frame when user places the cursor over the icon 5 8 C STAFF The C Staff functions ate based on STAFF Concept Satellite Tracking Aided Fleet Fishing The STAFF Concept is designed for professional fishing purpose to allow monitoring the position of the vessels of a fleet from each vessel the fleet may have until 20 vessels max gt MENU C STAFF ENTER For more information see the specific User Manual 5 9 C WEATHER SERVICE C Weather Service 1s an innovative meteorological forecasting system with the ability to visualize the weather forecast overlaying it on cartography The weather data is held on Jeppesen Marine s weather server which can be accessed via a C COM modem connected to the chart plotter or by using the PC Planner or the DPS Dealer Programming System saving the weather data on a User C CARD The weather data are overlaid on a map page as layers The weather format data available are Data Type WIND Speed amp Dir WAVE Height amp Dir TEMPERATURE HUMIDITY VISIBILITY WEATHER TYPE Sun WEATHER TYPE Rain WEATHER TYPE Fog WEATHER TYPE Snow WEATHER TYPE Clouds WEATHER TYPE Partly Cloudy WEATHER TYPE Thunderstorm Fig 5 9 Weather data package User Manual NY 5 9 1 C WEATHER SERVICE MENU To select the menu gt MENU C WEATHER SERVICE
81. e Wind Speed unit among Kts Knots m s Bft Mph and Kph kilometers per hour The default setting is Kph gt MENU ADVANCED SETTINGS ENTER SETUP ENTER WIND SPEED ENTER 5 1 5 BEEPER Turns On Off the sound after pressing a key beep The default setting is Off gt MENU ADVANCED SETTINGS ENTER SETUP ENTER BEEPER ENTER 5 1 6 EXTERNAL WPT The coordinates of a Waypoint received from a GPS connected to the chart plotter can be stored into the chart plotter if the GPS is NMEA 0183 protocol compatible and support the BWC sentence this symbol remains on the screen for 30 seconds You may save it by placing a Waypoint or a Mark onto that symbol As soon as the chart plotter receives another BWC sentence with the coordinates of a new Waypoint the symbol moves to the new point The default setting 1s Off gt MENU ADVANCED SETTINGS ENTER SETUP ENTER EXTERN WPT ENTER 5 1 7 SHIP ICON MODE Sets the ship icon as Steady or Blinking The default setting 1s Steady MENU ADVANCED SETTINGS ENTER SETUP ENTER SHIP ICON MODE ENTER 5 2 FIX The Fix menu handles functions telated to the Fix gt MENU ADVANCED SETTINGS ENTER FIX ENTER 88 CU ee Manual 5 2 1 FIX CORRECTION Turns On Off the Correction from the positioning system If the new Correction is calculated but the Correction is not enabled the ship s positi
82. e of the chart plotter No current position fix is required because the chatt plotter simulates position data internally gt MENU ADVANCED SETTINGS ENTER SIMULATION ENTER 5 6 1 ACTIVATE SIMULATION Once the settings are selected turn on the Simulator DAC ee Manual gt MENU ADVANCED SETTINGS ENTER SIMULATION ENTER ACTIVATE SIMULATION ENTER To turn On the Simulation select Off The default setting is Off 5 6 2 SPEED To start the simulator you can insert the Speed value Using the cursor key select the Eer Speed and press ENTER The default setting is 01 0 Kts MENU ADVANCED SETTINGS ENTER SIMULATION ENTER SPEED ENTER 5 6 3 HEADING To start the simulator you can insert the Heading value Using the cursor key select the RE Heading and press ENTER The default setting is 000 M MENU ADVANCED SETTINGS ENTER SIMULATION ENTER HEADING ENTER 5 Ge 4 DATE AND TIME MENU ADVANCED SETTINGS ENTER SIMULATION ENTER DATE ENTER MENU ADVANCED SETTINGS ENTER SIMULATION ENTER TIME ENTER Using the cursor key insert the preferred Date and Time and press ENTER 5 6 5 CURSOR CONTROL Enables On disables Off the cursor control The default setting is Off gt MENU ADVANCED SETTINGS ENTER SIMULATION ENTER CURSOR CONTROL ENTER 5 7 AIS MENU AI
83. e selected PTX from the chart plotter memory and from the chart display Move the cursor over the PTX to delete Press ENTER using the cursor select DELETE and press ENTER A warning pop up window will be shown Select YES and press ENTER 5 11 4 2 Goto PTX The Goto PTX function activates the navigation to the selected PTX Place the cursor on PTX cursor Press ENTER using the cursor select GOTO and press ENTER If the navigation is set to the selected PTX to terminate the navigation press EN TER using the cursor select STOP GOTO and press ENTER 5 11 4 3 MOBILARM PTX List Page The MOBILARM Alarm Status List shows the list of all PTX that returned an alarm event To obtain the page press ENTER using the cursor select LIST and press ENTER PTX status RECOVERED Time of PTX creation PTX position Fig 5 11 4 3 Example of MOBILARM PIX List page 108 CS se Manual This page allows you to Goto Activates navigation to the selected PTX Once the navigation has been activated close all menus data pages if open and center the chart selected PTX Delete Deletes the selected PTX Show Centers the chart on the selected PTX Show All Selects the best chart scale to see PTX icons on the map at the same time 5 11 4 4 Show PTX The Show function is available when PTX has been received again it is already present on the chart plotter memory and it is the active one To select
84. eacon prominent specially constructed object forming a conspicuous vertical mark as a fixed aid to navigation E Buoy A floating object moored to the sea bottom in a particular charted place as an aid to navigation E Buoys and Beacons Buoys and Beacons are used to indicate to mariners recommended ot established Routes underwater dangers restrictions and regulations They can be lighted or not and are colored according to their international code E BRG Bearing Angle between the North True or Magnetic and a destination It represents the direction to follow E Chain Selects the preferred chain The Loran chains are groups of transmitting stations that use timed radio pulse User Manual transmissions In each of these chains there is a master station and two or more slave or secondary stations Stations belonging to a same chain transmit pulses in timing groups a different time base identifies each chain The time base of each chain is the Group Repetition Interval or GRI This GRI identifies the chain in unique mode For example the GRI 4990 identifies the chain of Central Pacific zone E Chart Lock When Chart Lock is On the available zoom scales are only the ones containing cartographic data Instead when Chart Lock is Off it 1s possible to zoom down into zoom scales not covered by cartographic data after the last available zoom scale covered by cartographic data Warning When an empty level is entered the m
85. ed to this Target POSITION 43 08 844N f SOG Kts COG M 000 DST Nm BRG M 022 MAP DATUM WGS 1984 l i i es LIPTMA SNm Fig 4 1 1 5 Selecting destination Target The destination will automatically switch to the next Waypoint on the route when you reach or pass the present destination User Manual 6 Time To Go When the Target is set the TTG value is displayed in the Graphic Data page gt PAGE more times to select Graphic Data page Note If SOG value is less than 1 0 knots or the BRG is greater than 90 degrees the TTG value is not displayed Deleting Target If in Basic Mode place cursor on Target icon and press CLEAR the symbol that identifies Target disappears from the screen but the Waypoint remains If in Advanced Mode see Pat 3 4 3 place cursor on Target icon press ENTER select STOP NAV and press ENTER the symbol that identifies Target disappears from the screen but the Waypoint remains NOR c a If you select NEXT PREV and press ENTER the Target icon is moved on the next previous Waypoint in the route Otherwise in both Modes when the cursor is placed in a generic position on the chart press DEST A window appears to advice that the Destination point is present select STOP and press ENTER the symbol that identifies Target disappears from the screen but the Waypoint remains Note Ifyou select START and press ENTER the Ta
86. eferred setting follow the procedure gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 2 INPUT ENTER Then choose your preferred setting among the NMEA available settings NMEA 1200 N81 N NMEA 4800 N81 N NMEA 4800 N82 N NMEA 9600 081 N NMEA 9600 N81 N the default setting is 4800 N81 N and press ENTER to confirm 2 4 4 C COM CONNECTIONS To connect the modem C COM to the chart plotter follow the procedure 1 Connect Power amp I O as follows PIN CABLE COLOR FUNCTION i PWR GND COMMON PWR 10 35 Vdc Used by C COM Used by C COM OUTPUT 2 Used by C COM INPUT 2 OUTPUT EXTERNAL ALARM Fig 2 4 4 C COM Connection Note The connection is valid for the C COM IR and C COM RS232 too 2 Into the Input Output menu set the C COM for Port 1 as follows gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 1 INPUT ENTER C COM ENTER Also the modem C COM can be connected to the other Ports in this case set the format for the selected Port 2 4 5 EXTERNAL ALARM CONNECTION To connect the External Alarm device see the following picture User Manual DS POWER amp I O POWER SUPPLY POWER amp I O CONNECTOR CABLE PIN CABLE COLOR FUNCTION IS o 1 BLACK PWR GND COMMON GF RED Me Vde 8 BLUE OUTPUT EXTERNAL ALARM Open Collector Fig 2 4 5 External Alarm Connection O
87. erous high voltage circuits which only experienced technicians can handle E The C MAP By Jerresen C CARD are available from your local dealer E We will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material E Exposure of display to UV rays may shorten life of the liquid crystals used in your chart plotter This limitation is due to the current technology of the LCD displays Avoid overheating which may cause loss of contrast and in extreme cases a darkening of the screen Problems which occur from overheating are reversible when temperature decreases Warning on Serial Ports Connection gt gt gt Please be aware that the serial ports are not opto isolated and then the external device is electrically connected to the chart plotter This allows the connection of high speed devices like Fish Finder Ifyou are connecting a NME40183 device and you would like to isolate it from the chart plotter you have to add the opto isolator externally Table of Content User Manual idee te 0 1 EE 13 T1 CONVENTIONS soseri rined ai iE EAA EAREN 13 FETE 13 12 1 Nr 14 1 2 1 1 Main Characteristics uuaassmnamunenrinmemssmna 14 T2212 Physical Cachet sssri kaiini 17 To BASCS EE 18 Before YOU CTT Un NEE 19 21 TAE KEYBOARD ME 19 2 2 TURNING THE CHART PLOTTER ON AND OFF ccccceeeseeetteees 22 Aal TONNO AG GE 22 EG Le OR EE E 22 2 3 SELECTI
88. essage No cartographic coverage is shown on a window in a corner of the map display The warning message is always displayed as long as the current zoom has no data coverage E COG Course Over Ground Direction of the path over ground actually followed by a vessel E Correction To compute fix error in automatic mode place cursor on ship s real position and then follow the procedure compute correction It is also possible to compute the fix error in manual mode correction offset Once you computed the error you can turn the fix correction On or Off E Course Vector Graphical indication of the direction in which the Vessel is heading The Course Vector origin is the vessel s position so the time line movement is synchronized with the vessels Icon Course Vector coutse is given by the value of COG Course Over Ground and its length is proportional to the SOG Speed Over Ground E CTS Course To Steer The optimum direction the boat should be steered in order to efficiently make headway back to the coutseline while also proceeding toward the destination Waypoint E Cultural Features Any man made topographic feature as built up area buildings roads E Datum The Latitude and Longitude lines printed on any map are based on certain models of the shape of the earth these models ate called Datum or Coordinate Systems There are many different Datum in use each one gives different Lat Lon positions for an identical point on the
89. et from the Input Output menu Not Detected the device has never been detected since the chart plotter was turned On and input format was set to MOBILARM Connected the communication with MOBILARM device is Ok Signal Lost the device has been detected but now the signal is no longer received No Valid GPS Position the communication with MOBILARM device is Ok but the GPS position fix is not received 5 11 3 MOBILARM PTX PTX is the personal transponder device that is worn by the crew If a PTX is disconnected from the system a man overboard alarm is raised So a MOB Waypoint ap pears on the chart plotter display In the following for brevity this MOB Waypoint position is called PTX Warning Activating navigation to PTX pay attention and don t get too near the man overboard don t knock the man down 5 11 3 1 PTX is received When a PTX has been received the PTX data are saved on the chart plotter memory and the PTX icon appears on the map 106 Use Manual Fig 5 11 3 1 PIX icon All menus and or pages are closed and the chart is centered on the PTX received position The Audible Alarm starts beeping and a pop up warning window appears to no tify that a PTX has been received MOBILARM 33 27 090N 220 34 020W T Id Time 000001A0 10 16 29 PM L Fig 5 11 3 2 Example of PTX warning message It is possible to navigate to the received PTX see Par 5 11 4 2 and open the MOBILARM PTX List
90. ete 20 58 Deleting CA KE 108 Deleting route rrrrrnvrnrnnnnrnr 61 66 68 Deleting Target srnnnnnnnnnnnnvanennnn 39 62 Deleting the A B C D points 38 76 Deleting the A B C D Segment 76 Deleting Track ceccuiscnistaevcerenenostexgneteniaties 77 Deleting User Point neen 65 Deleting Waypoint A 60 EE 35 Depth Alarm NEE 17 Depth Area Range annnnnnnnnnnnnnnnnnnennn 122 Depth Graph chececewsse resessie 31 DEE es 122 Depth Range Max 08 15 46 47 Depth Range Min evvnnnrnnnnrr 15 46 47 Dept UN E 17 128 Depth Window EE 34 Depths amp Land Elevation 008 40 DES W 20 destination rrunrrrrnnnrnnvuvnnnnnr 61 62 81 Detailed Port Plan 40 Detailed World Background 40 BLE EEE 122 Bs ENE 124 Differential Correction Source 36 Differential GPS oo eee 122 DIffUSers o oo ee ceee cess eeee eens 15 46 48 Dim Menu verrnnnrevnrnvanennnnnnnnevnnnvunensnne 117 KEE 17 Display Mode sce teiswaccsnentetwnszanscvnies 15 45 Display Settings E 118 Displaying Track E L Distance rrnrrnnnnnnrnnnnanevnnevnnennnnnnnnr 14 34 distance track rrrrrrvvrvvrrvrrvrrrrrrrnnnnnn 78 Distance Unit rrerrrrvnnnrernnrrevrerenrnrennnr 17 Distress Call 101 Download er 100 Download Area errnrrvvrrnrnvnrnnnnvvrvnrrerrs 100 DSG sans isernia nas 16 101 122 DSG Directory vasene 104 DSC LOG EE 103 DSC Men 103 5 EE EE 44 Dynamic
91. ey 1s pressed 2 by selecting the page from the Page Selection menu The desired way to select the page is set by changing Page Preview following the procedute gt MENU BASIC SETTINGS ENTER PAGE PREVIEW ENTER When Page Preview is Off PAGE allows setting the next page 1 When Page Preview is On PAGE opens the Page Selection menu 2 on which the icons representing the pages are shown the icon of the currently selected page is identified by a bold frame move the selection with the Cursor keys or PAGE the name of the currently selected page icon is shown in the lower side of the Page Selection menu Pressing ENTER the Page Selection menu is closed and the currently selected page 1s activated User Manual DD 3 1 1 CHARTS AND TEXT AREA The charts and text area can be shown in two different modes The first is with text area on the right side of the screen Fix received Indication if fix is not received the following icon is shown ts if a Differential GPS signal is received the following icon is shown d Charting or Navigation Home I Ship icon Ai if in Charting the displayed icon Is lt gt POSITION 43 01 767N 008907 970E M Speed Over Ground 7 d SG Kts COG 4 LOM TO CURSOR Nm BRG M Course Over Ground 40 97 090 MAP DATUM WGS 1984 SCALE Map Datum selected Z tie Fig 3 1 1 Chart General Data
92. from PCMPN 1 No of Wpts from Destination to last Wpt from PCMPN 1 distance from ship to Destination calculated distance to travel from ship to the Wpt after the des tination calculated Distance to Dest Next Route Leg length distance to travel from ship to the end of the Route calculated Distance to Dest Distance from Dest to last Wpt received from PCMPN 1 estimated time to travel the Distance to Last Wor Calculated using Cruising Speed estimated time to travel the Distance to Next Waypoint Calculated using Cruising Speed estimated time to travel the Distance to Last Wpr Calculated using Cruising Speed Estimate Time of Arrival to the Destination point Calculated Current Time TTG To Destination Estimate Time of Arrival to the Waypoint after the Destination Calculated Current Time TTG To Next Waypoint Estimate Time of Arrival to the end of the Route Calculated Current Time TTG To Last Wpt Route Navigation Quick Info on the Destination Route Name DESTINATION ID Wpt1 4 Last 8312 06 41 544 Distance TTG and Consumption from Ship to Dest Houle Lenglh 71 18 Nm Distance TTG and Consumption from Ship to Last Wpt Fig 4 8 1 8 Quick Info on Destination Quick info on Single Destination EXTERNAL DESTINATION WPTOO2 Der BRG 7 41Nm 082 M Fig 4 8 1 8a Quick Info on Single Destination User Manual 8S
93. function is not used it maybe disabled 3 5 1 8 Safety Status Bar DSI Data Safety Indicator gt MENU MAP SETTINGS ENTER Safety Status Bar ENTER It is possible to choose between the three following options gt ON the Safety Status Bar is shown OFF the Safety Status Bar is not shown e ICON the Safety Status Bar is not shown but a warning alarm icon is shown on the corner of the map screen as soon as any item con trolled by the DSI function returns an alarm condition The Warn ing Icon remains displayed until the alarm condition persists Plac ing the cursor over it a quick help message is shown next to the DSI icon allowing to show the DSI bar In this case when the DSI bar is opened via DSI alarm icon it is allowed to obtain information about each active DSI box the red ones tt 1s pos sible to select them by cursor movement left right and a list of active alarms 1s shown underneath the selected box By pressing CLEAR the DSI bar is removed from the screen When Safety Status Bar is On this feature displays a status bar with six boxes showing the status of certain functions Any warning or alarm condition is identified by the red colour to indicate possible risk NORMAL BEST MAP DATA OFF DECLUT DANGERS CAUTIONS Fig 3 5 1 8 Safety Status Bar Boxes definition is as follows 1 Zoom Normal when the chart is displayed at normal scale U Zoom ted when the c
94. hart is under zoomed out mote than twice normal scale gray otherwise 0 Zoom ted when the chart is over zoomed in more than twice normal scale gray otherwise Chart Lock ted when the chart is zoomed in more than twice normal scale gray otherwise Q Best Scale Red when a more detailed chart is available under the cursor position AC ee Manual 3 Data Off Red when at least one of the following objects ot layers is turned off by the user Depths soundings Wrecks obstructions Tracks routes Attention areas Nav Aids 4 Clear View Displays when Cleat View function is On 5 Dangers Red when Guardian Technology detects one of the following objects Land Intertidal Depth Area Rocks Obstructions Shoreline Constructions Fishing Fa cility Wrecks Dragged area Diffusion area Mooring facilities Pingos and Produc tion installations 6 Caution Red when Guardian Technology detects cautionary or restricted area 3 5 1 9 Satellite Imagery gt MENU MAP SETTINGS ENTER SATELLITE IMAGERY ENTER It is possible to overlay the Satellite image for background map When it is set On the Palette 1s set to Normal to display the proper colors 3 5 1 10 Currents Prediction gt MENU MAP SETTINGS ENTER Currents Prediction ENTER It is possible to see the variation of the Tidal arrows on the selected area at any given time A window is shown on the low left side of the char
95. he characters of the name name message box The details on Land Source of Data Cartographic Area and Spot Soundings are not shown User Manual YD DIGA ap N e POSITION Pn SPEC PUNR I 42954 119N G 08919 311E EICH 18512m7M G Kts COG M 4 0 000 IT Nm BRG MM 94 54 0659 MAP DATUM SCALE eI 1 Nm Fig 3 5 2 Automatic Info on Points window If you press ENTER you get the information about that object 3 5 2 1 Info on objects with Pictures On the Quick Info there will be the camera icon on the top bar of the window if at least one of the objects found has one or mote pictures associated OBJECT E Building single m Sia to expand Fig 3 5 2 1 Example of Quick Info on objects with picture On the Full Info there will be the small camera icon on a corner of the square containing the object icon or a big photo icon centered on the square for the object without icon Land el Land elevation Di National territorial area Data source Building Multimedia Information MultiMedia Object ENTER to show the picture Fig 3 5 2 1a Example of Full Info on objects with picture To see the picture press MENU when the object with a picture is highlighted Change Picture Size When the picture is shown it is possible to fit it to screen by pressing ENTER 50 User Manual 3 5 2 2 Quick Info on Lakes Upon viewing the chart of a lake you will click on to query the avai
96. her chart plotter The two MAX data C CARDs must have the same code and revision So the MIRROR C CARD can be utilized only on a chart plotter linked to another chart plotter provided with the equivalent REGULAR C CARD It is important to point out that the two chart plotters must have the update software versions that allow C Link function 4 7 1 HOW C LINK SYSTEM WORKS When the chart plotter is powered up it switches into the Stand Alone Mode In this work mode the chart plotter unit periodically scans all the available C CARD slots searching for MIRROR C CARDs When one or more MIRROR C CARD is found in SOC ee Manual one ot both chart plotters a special connection is established between the chart plotters to habilitate the MIRROR C CARDs If a regular C CARD which has previously activated a MIRROR C CARD is temoved even the MIRROR C CARD will be not read anymore on the other unit 4 8 C LINK NAVIGATION DATA TRANSFER This function allows transferring C Link Navigation Data Route Name Destina tion ID amp Position Next Waypoint ID amp Position Total Route length Fuel Consumption Rate ETA TIG etc between two chart plotters linked through the C Link system The chatt plotters can be set to operate in two modes MASTER mode Primary chart plotter that sends data SLAVE mode Secondary chart plotter that recetves data When the navigation 1s activated on the Master chart plotter the C Link Naviga tion Data will be
97. igation system operated by the US Department of Defense It gives the navigator a posi tion 24 hours a day 365 days a year under any weather conditions E HDG Heading Horizontal direction in which a ship actually points or heads in any moment see also COG E HDOP Horizontal Dilution Of Precision Index for position fixing accuracy The smaller the HDOP value the more accurately the position can be fixed E Home In this operating mode called also Navigate mode all operations refer to the ship s position E Latitude Angular distance North or South of the equator measured by lines encircling the earth parallel to the equator in degrees from 0 to 90 E LAT LON Coordinate system using Latitude and Longitude coordinates to define a position on earth E LOG Speed of the vessel relative to the water E Longitude Angular distance East or West of the prime meridian Greenwich meridian as measured by lines perpen dicular to the parallels and converging at the poles from 0 to 180 E Loran The Loran Chains are groups of transmitting stations that use timed radio pulse transmissions E Magnetic Deviation Angle between the Magnetic North and the Compass North E Magnetic Variation Angle between the magnetic and geographic meridians at any place expressed in degrees West or Fast to indicate the direction of magnetic North from true North It changes from point to point and at the same point with time E Mark Refe
98. ill not be moved to the next Waypoint on the Route MOB handling If the navigation to the external destination is active and MOB ts pressed on the Slave chart plotter the MOB is placed but the navigation to the MOB 1s not activated Notes While navigating to the external destination the operating mode is switched to Master mode the navigation to the external destination will be terminated An appropriate warning mes sage will be shown to notify that the navigation to the external destination 1s active and to confirm whether Slave mode can be set Setting Slave mode the C Link Navigation Data will be deleted The C Link Navigation Data are deleted at Power Off User Manual 8 4 8 1 5 C Link Navigation Data acquisition and display s soon as the C Link Navigation Data is received the Slave parses the information recetved and executes the relative actions depending on its current working status Important gt When the navigation to the external destination is activated the Slave chart plotter will show all relevant C Link Navigation Data exactly like when the destination is not the external one Destination Name DST and BRG to Destination calculate XTE calculate VIG etc These values will be displayed all places where required and they will be used to format NMEA 0183 output data 4 8 1 6 Graphical representation on Map Display External Destination RED Icon WPT002 Next Waypoint GREEN Icon WPT003
99. ils Depths amp Land Elevation color shading of sea depth and land altitude for improved chart reading Bathymetric amp Spot Soundings additional Data Base with depth and bathy information for an extraordinary view of the seabed depth Detailed Port Plan complete port and marina charts with detail Search amp Find quickly locates chart contents and objects Tides Preview dynamic simulation of tides Dynamic Currents current arrows dynamically display direction and speed Dynamic Nav Aids dsplays Nav Aids in true color and with real interval lighting Port Info all the information of the available services in the ports and how to contact them Enhanced Port Info amp Roads details of the available facilities and services in ports and surrounding areas Object Info indicates restricted area details and related information Quick Info fill information on objects buoys wrecks shoals and Nav Aids Photos amp Diagrams high definition pictures of ports piers bridge diagrams and nav aids Multilanguage Support displays charts in the local character set True Type Font improves text on chart for optimal reading Presentation Features Clear View advanced legibility techniques providing more chart data on the screen Cleat Info sophisticated Human Dictionary to translate Nav Aid abbreviations found on 4 User Manual paper charts Dynamic Nav Aids an innovative and dynamic presentation mode Flexi Zoom increased Under and
100. ing Mark gt Select Advanced Mode Place cursor on Mark Press ENTER Select DELETE and press ENTER the Mark remains on the screen shaded until the next screen is redrawn Note If you try to delete a Mark that belongs to many routes the chart plotter emits three beeps and on the screen a Warning message appears If you want to delete the Mark press ENTER M SC eer Manual 4 2 1 3 Goto gt Place cursor on Mark Press DEST a circle encloses the Mark symbol A straight line is shown on the screen connecting the Target with the ship s position When the Target ts placed all naviga tion data are referred to this Target 4 2 1 4 Moving Mark Select Advanced Mode Place cursor on Mark Press ENTER Select MOVE and press ENTER Move the cursor by the cur sot key a dotted line connecting the Mark with the new position is shown Dis POSITION 43 09 124N 009 S53 757E SOG Kts COG mM 4 0 0009 OST Nm BRG M 39 89 0129 SCALE D x 4 k MRK S fr y TO CURSOR 4 Fig 4 2 1 4 Moving Mark function 1 Press ENTER S e POSITION 43 09 143N 009 53 757E SOG Kts CoG M LL 000 TO CURSOR DST Nm BRG M 0470 MAP DATUM i WGS 1984 Te Ge CN SCALE 7 HH Nr a 2 Nm e Fig 4 2 1 4a Moving Mark function II The Mark is placed in the new position the old Mark remains on the screen shaded until the screen is redrawn Note Tf
101. ing the A B C D points rernnnnnnrnnrnneneennernnernnrnnnnevnersevnsennnnne 76 4 4 5 Inserting the A B C D points use EEE REENEN 76 4 4 6 Navigating on the A B C D points rnrrrnnnnnnnnnnnvnvnvvnvnnnnnnnnnnnnnnn 76 4 5 USING THE TRACK FUNCTIONS tivscincssuenianinniveddessnmonsesuedtedeciadiucdsduvans 76 451 Selecting active Ve 77 252 Enabling Track e o Te NEE 77 453 Displaying DR WEE 71 4 5 4 Selecting track Color srvvverrvrererverernnnnnnnnenennnnnnnnnnnvnvenennnensenenener 77 255 P Tre 77 4 5 6 Deleting Selected Track 77 4 5 7 Selecting Track memorizing type e seseeeeeeeeeeeeeeeeeeeeeeees 78 4 5 8 Selecting ele Te 78 459 Selecting IME serseri aiani oni SEN NSE ERRENA nA 78 4 6 USER C CARD MENU vr 78 AGT Saving File E 79 Bee NE 79 AGS Deleting E 80 4 6 4 Formatting User CG CARINE 80 4 6 5 Changing User C CARD cicisvicsadentsvniassiveareianatsavisesassbveveiwiiaeandnberns 80 4 7 C LUNK gt NE EEE EN ENE 80 4 7 1 How C Link system works Senge getgebageeresrs eggr ee Eed EE Eege Eeebeeg 80 4 8 C LINK NAVIGATION DATA TRANSFER ennnnrvvevrrrrnrnnnvnvnvnrerrrrnssnnrnneenr 81 OS el 81 4 8 1 1 Introductive elements rrnnnnrnrvnvvvvvnvrerrrrrvrvrrrrrnrnernrnnn 81 48 12 G LINK senal ele 82 4 8 1 3 Master Chart e EE 82 Operating 10100 EE 82 48 14 Slave Chart Plotter vezuaseaamsasbsnenpemrmnnadeie 83 Op rating MOTE EE 83 4 8 1 5 C Link Navigation Data acquisition and display
102. int Bearing from Destination to next Waypoint Route Length Distance from Destination to Last Route Waypoint Remaining Route Legs Planned Cruising Speed Average Fuel Consumption Initial Fuel Load C Link Navigation Data can refer to Single Destination navigation Route Following navigation Values identified by are sent only for Route Following navigation The Destination Icon Navigation leg Fix Position to Destination the Next Waypoint Icon and all other relevant C Link Navigation Data will be shown on the Slave chart plotter Any variation of the C Link Navigation Data on the Master will be communi cated to the Slave so to keep data aligned on both devices 4 8 1 2 C Link serial connection The two chart plotters should be connected via serial ports Any of the available ports can be used the software will recognize automatically the sertal ports used A typical connection is as follows Chart Plotter 1 Chart Plotter 2 TX RX RX Bee TX GND gt GND 4 8 1 3 Master Chart Plotter Operating mode To select the Master mode Primary Station follow the procedure gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER C LINK ENTER Primary Station ENTER Master mode is the default factory setting All regular chart plotters functions are allowed As soon as the Destination is placed the Master chart plotter will start transmitting all C Link Navigation Data In Master mode the C Link Navigati
103. ission The Distress Call that allows to receive a position of the vessel in distress and the User Manual 101 Position Request a great feature for anyone wanting to know the location of another vessel for example you buddy that is catching fish or finding the location of a person you are cruising with are performed by an external device the DSC VHF radio The chart plotter interfaced with a DSC VHF radio prompts the uset to see the GPS position of the vessel in distress and also allows for easy navigation to the vessel The Distress Call and the Position Request icons that are displaying on the screen are shown in the following table DESCRIPTION SYMBOL Position Request icon Distress Call icon Fig 5 10 Distress Call and Position Request icons Note The label can be the MMSI or the corresponding vessel s name If in the DSC Directory the MMSI has been associated to its relative vessel name the vessel s name is shown in the label instead of the MMSI 5 10 1 DISTRESS CALL AND POSITION REQUEST During a distress situation a vessel that is equipped with a DSC VHF radio and connected to a GPS has the capability to transmit a DSC Distress Call with GPS Position When the VHF radio receives a DSC Distress Call the position information of the vessel in distress is transferred to the chart plotter The chart plottet logs the Distress Call into the DSC Log and also marks the position of the vessel in distress on the Chart
104. ks Events and Waypoints Move up down the cursor key to select the User Point you wish If the page contains more than 8 User Points the list continues in the next pages See Par 4 1 1 9 4 2 2 6 Add to route gt Place cursor on Event Press ENTER Select ADD TO ROUTE and press ENTER the selected Event is connected to the current route The same Event can be added in many routes NOE An existing Event can be connected to the current route in another mode too Place cursor on Event the information window related to the Event appears press CLEAR to close the window and then press ENTER select the Waypoint option and press ENTER The Event is connected to the current route 4 3 EBL amp VRM FUNCTION EBL amp VRM function enables to create a dotted line and a circle respectly with direction and radius determined by the uset 4 3 1 PLACING EBL amp VRM Select Advanced Mode ENTER EBL amp VRM ENTER ot ON MAGNUM Pus gt ErrL VrM if it is present On the screen a dotted line and a circle appear you can move in any direction you choose moving the cursor keys When the desired position is selected press ENTER A window is shown containing the beating value for the EBL and the radius value for the VRM 4 CS eer Manual 47 VU Jalocle x p e 44 25 490N 0 ROTATORIO pa 008 41 250E 1 0 000 d gt A i TO CURSOR SCALE bete Fig 4 3 1 EBL amp VRM 4
105. lable informa tion immediately displayed with many details For example see the following picture Lakes Info icon When the cursor is placed over the icon the icons of the available services are shown Fig 3 5 2 2a Quick Info available services If you press ENTER all available information about the cartographic point under the cursor will be shown See the next paragraph 3 5 2 3 Full Info on Lakes The following is an example of Full Info on Lakes User Manual 5 OUT DNR RECREA T TIONAL AREA STATE FISHING BEASDON AND BAG LIMITS HILT Tae SEASON AND BAG LIMITS BEID FEFHAINT WALLETE TROUT RAIMEOW h TROUT LAKE TROUT BROWN TROUT BROOK SUNFISH PAUMPKINGEED SUNFISH BLUEGILL SHAD AMERICAN SALMON KOK ANEE PIKE NORTHERN PICKEREL CHAIN PERCH YELLOW PERCH WHITE CATFISH WHITE CATFISH CHANNEL CARP COMMON BULLHEAD BROWN BASS SMALL MOUTH RASS ROOK BASS LARGEMOUTHM AMERICAN EEL TMA TI RI to show Picture Fig 3 5 2 3 Example of Full Info page To see the Fishing object press MENU when the Fishing object is high lighted On the screen appears Walleye Fig 3 5 2 3a Example of picture associated to the Fishing object 3 5 3 INFO TREE AND EXPANDED INFO PAGE This page combines the Info Tree and the Expanded Info pages this gives the advantage of showing the details of the object selected on the Info Tree while the cursot is moving through the Info
106. map scrolls underneath as the fix position changes To deactivate Home mode move the cursor In Basic Mode deletes the A B C D points the User Point Mark Event Waypoint the MOB the Target identified by the cursor The key Selects the desired option confirms selection ONLY ON MAGNUM Pro pressing ENTER in Basic Mode places B C D points on the cursor coordinates in Advanced Mode creates Objects Waypoint EBL VRM A B C D ONLY ON MAGNUM Prus pressing ENTER in Advanced Mode creates Ob jects Mark Event Waypoint EBL VRM User Manual LE Moves the cursor about on the display screen quickly and accurately The cursor starts moving slowly the cursor key is initially pressed then accelerates after a while if the cursor key is pressed and hold It also scrolls the desired option in the menu page s up down move the current menu selection right executes the function assigned to the active selection in the menu same as ENTER left quit menu same as CLEAR If in Home Navigate mode it allows to exit from Home mode The Gu and kB keys Press ZOOM IN shows mote details of a smaller area by changing the chart scale and zooming in on your display Press ZOOM OUT to operate similarly to the ZOOM IN except in reverse changing the scale and showing a wider otherwise less detailed view The key ONLY ON MAGNUM Pius Press VOD to place MOB Man OverBoard Pressing VOD when
107. mits three beeps and on the screen a Warning message appears If you want to delete the Event press ENTER 4 2 2 3 Goto gt Place cursor on Event Press DEST a circle encloses the Event symbol A straight line is shown on the screen connecting the Target with the ship s position When the Target ts placed all naviga tion data are referred to this Target 4 2 2 4 Editing Event gt Place cursor on Event Press ENTER Select EDIT and press ENTER A window appears to modify Name Symbol Color of the existing Event d LE gf a UH i H N I I L j POSITION 43 09 196N 009953 757E Jevra s SOG Kts CoG M Giraglia 009 53 755E 000 DST Nm BRG M 0 750 MAP DATUM WGS 1984 SCALE H SNm User Manual o y Use the cursor key to select the field If you have selected Name field press ENTER use the cursor key to insert the character 8 characters max then press ENTER If Color field is selected press ENTER a window with 8 different colors appears use the cursor key to select the desired color and press ENTER If Symbol field is selected press ENTER a window with 16 different symbols appears Use the cursor key to select the symbol and press ENTER Then press CLEAR 4 2 2 5 Finding information on Events User Points List page gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER A full window is opened showing information about all stored User Points Mar
108. mnomessssirisnmsnria osnme 66 4 1 2 2 Route name snr genee Eed ee 66 4 1 2 3 Deleting route een 66 4 1 2 4 Reversing route E 67 4129 MOWE COOL EE 67 4 1 2 6 Send Receive route ccccceseseseeecencccececeeeeeeeeeeeeeeees 67 4 1 2 7 Finding information on route Route Report 67 es 19311110 go 10 E 68 Changing Speed amp Fuel values rrannnnnnnnnnnnnnnnnnnnnn 68 Reversing roul EE EE iaSi 68 Deleting MOUS EE 68 4 1 2 8 Safe Route Checking r rrnnnnannnnvnvvvvvvvvvrvvvvvevenernannnnennn 69 4 2 MARK amp EVENT ee 70 EG NE 70 2 WE elle RO 70 42 1 2 PENN ae 70 42 13 TN 71 212 MOVNO MAK Laser r 212105 ENN D 4 2 1 6 Finding information on Marks User Points List page 72 4 2 1 7 Add t route seede 72 4 2 2 Events EE 72 4 2 2 1 Adding Event E 73 4222 AN EAN eee ne 73 ER EE 6 0 EEE EE EE EE EE 73 4224 BEN E 73 4 2 2 5 Finding information on Events User Points List page 74 4 2 2 6 Add t e 74 4 3 EBL amp VRM FUNCTION WE 74 201 Placing EBLA VRM EE 74 432 Deleting EBL Verd 15 4 3 3 Editing EBL amp Ve 75 4 4 MORE ABOUT A B C D FUNCTION cc ccccceeessesssteeeeeeessessssseeees 75 4 4 1 Inserting the A B C D points rrrrrnernernernnennernvernerrerrevrseensenssnnnnnne 75 4 4 2 Deleting the A B C D points rronnnornornernvennennnnnnnnnerrerseensensennnnnen 76 4 4 3 Deleting the A B C D segment rmrnnnnnnnnnnnnnnnnnnnnnnnnnvnvnvnnnnnnnnnnnr 76 4 4 4 Mov
109. n insert a Waypoint between two existing ones find any Waypoint at anytime Every time you place the cursor on a Waypoint the following functions are available 4 1 1 1 Adding Waypoint Select Advanced Mode ENTER WAYPOINT ENTER ot ON MAGNUM PLus gt Wayroint if it is present The Waypoint appears on the cursor position An info window is shown contain ing route number Waypoint name symbol and Latitude Longitude User Manual ID GE POSITION 42 54 437N WAYPOINT p 008 19 311E ROUTE1 WPToo1 AE i SSE H RECH 4 0 0009 ST Nm PER M E Kapen y MAP DATUM Bs WGS 1984 LS SE Se SCALE SE a rrara Fig 4 1 1 1 Waypoint placing 4 1 1 2 Creating a route Repeat the Adding Waypoint procedure described in the previous Par 4 1 1 1 The sequence of moving the cursor and pressing ENTER is continued to create the route until you have reached the last Waypoint your final destination Segments connecting the Waypoints are shown and the starting point is identified by a circle surrounding the first Waypoint of the route HK POSITION 42 54 456N TO CURSOR ST Nm BRG M 74 72 0940 MAP DATUM 3 WGS 1984 7 SCALE HH 4 1 NM Fig 4 1 1 2 Route planning 4 1 1 3 Deleting Waypoint Select Advanced Mode Place cursor on Waypoint SC locla BEN S f POSITION EN 42 54 476N KN 008 19 3141E HPT BI WPT
110. n Areas Tides amp Currents Seabed Type Ports amp Services Tracks amp Routes Depth Settings Depth Range Min Max e Land Settings Land Elevations Land Elevation Values Roads Points Of Interest e Chart Settings Lat Lon Grid Chart Boundaries Value Added Data Chart Lock e Underwater Objects Settings Underwater Objects Limit Rocks Obstructions Diffusers Wrecks Map Settings 3D View Perspective View e Palette Map Orientation North Head Course Zoom Type e Fonts amp Symbols Dynamic Nav Aids e Mixing Levels e Safety Status Bar e Satellite Imagery e Currents Prediction e Chart Language Fix Functions Fix Correction manual and automatic Position Filter e Speed Filter User Manual 45 Dead Reckoning Reset Total and Partial Trip Rolling Road Scale e Fix Datum Compass Calibration Bearings True and Magnetic Variation user selectable e Course Vector Static Navigation e A B C D Function EBL amp VRM Function Report Pages e Depth Graph Page GPS Status Page Navigation Data Page 3D Navigation Data Page Fish Finder full screen Page e Fish Finder Dual Frequency Page e Fish Finder Zoom Page e Chart Fish Finder Page Radar full screen Page Radar Chart Page Radar Fish Finder Page e Radar 3D Navigation Data Page Radar Fish Finder Chart NavData Page e Wind Data Page About Page Special Functions
111. n data time is available Tidal stream arrows are shown on the charts indicating the direction and strength of the Tide Fig A 1a Tides amp Currents If no data time is available from the GPS or the chart plotter is not in Simulation mode the icon on the map is generic one The color of the arrow denotes the strength of the current as follows O to 0 1 kn 0 2 to 1 0 kn 1 1 to 2 0 kn 2 1 to 3 0 kn 3 1 to 9 9 kn Fig A 1b Tides amp Currents table When the chart plotter receives a valid position fix the Tide icons are shown on the charts on the basis of the current date and time the screen displays and changes arrows as date time changes E Time Line The location where the ship will be after the time set by the user E Tracks amp Routes Recommended and established routes for ships at sea including traffic separation schemes deep water routes User Manual 125 E TRN Turning Difference between COG and BRG If COG is 80 and BRG is 75 TRN is 5 Left E TTG Time To Go Estimated time needed to reach your destination based on your current speed and the distance to destination E User Point Place on the chart identified by its coordinates and displayed on the screen with a reference symbol see Mark Waypoint and Event E UTC Universal Time Coordinated Time scale based on the rotation of the earth that is used by most broadcast time services E UTM Universal Transverse Mercator Metric
112. nce the connection is active to enable the External Alarm follow the procedure gt MENU ADVANCED SETTINGS ENTER ALARMS ENTER EX TERNAL ALARM ENTER ON ENTER 2 5 ADDITIONAL C CARDS The chart plotter uses two types of C MAP By JEPPESEN cartridges either a chart cartridge or a data storage cartridge A chart cartridge called C CARD contains detailed charts of the area covered A data storage cartridge called User C CARD can be used to permanently store your routes Waypoints Marks Events and tracks Note During normal operations the C CARD should not be removed since the chart plotter may lock up 2 5 1 INSERTING C CARD Hold the C CARD by the short inclined side so that you can see the C MAP label INCLINED SIDES Fig 2 5 1 Inserting C CARD 1 Gently push the C CARD into one of the two slots 1 push the C CARD in as far as it will go then move it to the bottom 2 to hold fixed into the slot 3 WW User Manual Fig 2 5 1a Inserting C CARD II 2 5 2 REMOVING C CARD Press lightly the C CARD you wish to remove 1 and move it to the top 2 until you hear a click the C CARD will ejected out of the slot 3 L d An Note C MAP By JEPPESEN ts continuously creating new charts and revising old ones If you wish to receive information on the newest available charts you can write for the catalog of available C MAP By JEPPESEN C CARD at
113. nd use it left right to move cursor to left right 54 User Manual Note Tide graphs are an approximation of the tide and they should be used in conjunction with traditional tide tables and navigational methods 3 5 7 FIND FUNCTION The chart plotter allows finding Nearest Services Tide Stations Wrecks Obstruc tions Port By Name Port By Distance Lakes Info Lakes By Name Points Of Interest 3 5 7 1 Finding Port Services To locate and display the nearest available facilities of a particular type 1e the nearest Hospital sailmaker bank etc gt MENU FIND ENTER NEAREST SERVICES ENTER The icons of the available services are shown Use the cursor key to select any facility and press ENTER The list of the nearest ports up to 10 containing the facility will be shown on the screen Then choose the port you want and press ENTER 3 5 7 2 Finding Tide Stations Finds the nearest Tide Stations up to 10 on the map from the boat position if a valid fix is received or from the cursor position if the received fix position is not good gt MENU FIND ENTER TIDE STATIONS ENTER A new window will appear in few seconds Choose the Tide Stations you want and press ENTER or Finp to display the Tide Graph page see Pat 3 5 4 Press CLEAR to display the Tide Station chosen 3 5 7 3 Finding Wrecks Searches for nearest Wrecks gt MENU FIND ENTER WRECKS ENTER
114. nnnnnnnnnsenesrenrnrrrrrrrrnrnnnne 104 Delete All rrrnrrnrrrvrvrenererrrnonronnrsnnnnnnnnrnrnrrrnnnnenessenennr 104 5 10 3 Quick Info on DSC ICONS rrrrrnrnrrnornonnnnnnnnnnnnnnnrnrrrrnrnnnneneneessnsnnn 105 511 MOBILARM SY SIEM socccentoestcntasndanddeanescxodsascnotudacansuessindecteassensduoetadxteds 105 AT SPE NT 105 5 11 2 MOBILARM Status rrrrrrrrrrrrnerrrrornonnrnnnnnnnnnrrnrrrnnnnnnsenerssnsnnnnnnnnnn 105 5 11 3 MOBILARM PTX rrorrrrrrrrrererrrnerrarsrsnrnnnnnnnrnrrnrnrrnnnnnesnsnssnsnsnnnnnnnn 106 SKS PTA E ancrtssscansndeensnesiesdcbcuaneneasacetaseenutecensseedee 106 5 11 3 2 PTX is received again riet genge gege deeg Gree ebeetesgesgg 107 5 11 4 Moving Cursor on the PTX ICON wicseisniveaierinadseunseseassviecesdsetereeans 107 STAT SIS due F TA EE 108 51142 Goto PTX E 108 5 11 43 MOBILARM PTX List Page rrrrrnrnrrnrrrrrornrrnrnnnnrnnnnnnn 108 5 11 4 4 Show BIN en 109 512 FISH FINDER MENU E 109 5 13 RADAR SETUP MENU Lu usegseap ee 110 For he TECHNICIAN save 111 6 1 DIMENSIONS sceeceeesdecctened cedccdecseedsduinaianduadanddantsdecceacodesdentdsdexdsdeboiendaees 111 62 INSTALLATION seccesecserceaeccnaciocnssnnnsdelesnaacundseusepdoodnceacndiecunddvneaanduearadexeas 111 63 EXTERNAL WIRING sepscticeccceccicncacscpacnapstdunseatesnsnesneseedevincsidiacdenendunesacgeses 112 6 4 TYPICAL CONNECTIONS POWER amp I O Connector rrrrrrrrnrrnrn 112 6 4 1 GPS Connections rrrrnrrrnnnvvrvrrrrnnnnnrrrrovrvvn
115. on Data received from the NMEA port is ignored So if the two chart plotters are both operating in Master mode the C Link Navigation Data sent by the other chart plotter never processed Under such condition if the navigation 1s activated on one of the two chart plotters a warning message 2 0 User Manual will be shown to notify that the C Link Navigation Data will be ignored by the other chart plotter 4 8 1 4 Slave Chart Plotter Operating mode To select the Slave mode Secondary Station follow the procedure gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER C LINK ENTER Secondary Station ENTER When Slave mode is set the chart plotter cannot manipulate the C Link Navigation Data anymore Stop current navigation If the navigation was already active it will be disabled as soon as Slave mode is set An apptoptiate warning message will be shown to notify that the navigation is already active and to confirm whether Slave mode can be set Inhibit navigation operation As soon as Slave mode is set the destination cannot be placed anymore either the C Link Navigation Data is received from the Master or not Also when the C Link Navigation Data is received from the Master it will not be allowed to deactivate the navigation Inhibit route following While navigating to the Route received from the Master the destination is reached either applying distance or perpendicular criteria the destination w
116. on is not changed The default setting is Off gt MENU ADVANCED SETTINGS ENTER FIX ENTER FIX COR RECTION ENTER 5 2 2 COMPUTE CORRECTION Corrects fixes from the positioning instrument By placing the cursor on the ship s real position and selecting this option the error is calculated and internally memorized for appropriate correction but not applied gt MENU ADVANCED SETTINGS ENTER FIX ENTER COMPUTE CORRECTION ENTER 5 2 3 CORRECTION OFFSET Manual correction of fix position gt MENU ADVANCED SETTINGS ENTER FIX ENTER CORRECTION OFFSET ENTER Insert the preferred value and press ENTER 5 2 4 POSITION FILTER Turns On Off the Position Filter In case of a jittering fix this option makes the ship position more stable and the track smoother The default setting is Off gt MENU ADVANCED SETTINGS ENTER FIX ENTER POSITION FILTER ENTER 5 2 5 SPEED FILTER Turns On Off the Speed Filter When it is On you can filter the speed of the ship to optimize it The default setting is Off gt MENU ADVANCED SETTINGS ENTER FIX ENTER SPEED FILTER ENTER 5 2 6 FILTER DUMP Inserts the value for the Filter in the range 500 12000 The default setting is 500 gt MENU ADVANCED SETTINGS ENTER FIX ENTER FILTER DUMP ENTER User Manual 5 2 7 DEAD RECKONING Enables On
117. or disables Off the Dead Reckoning The default setting is Off gt MENU ADVANCED SETTINGS ENTER FIX ENTER DEAD RECKONING ENTER 5 2 8 STATIC NAVIGATION Sets up a threshold for the speed When the speed received from the positioning device is under that threshold the chart plotter displays zero speed The default value is 0 0 Knots gt MENU ADVANCED SETTINGS ENTER FIX ENTER STATIC NAVIGATION ENTER 5 3 NAVIGATE The Navigate menu allows to handle functions related to navigation gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER 5 3 1 COORDINATE SYSTEM Sets your preferred Coordinate System among ddd mm ss ddd mm mm ddd mm mmm UTM OSGB TD The default setting is ddd mm mmm gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER COORDINATE SYSTEM ENTER If TD has been selected a new menu is shown on the screen gt MENU ADVANCED SETTINGS ENTER NAVIGATE ENTER COORDINATE SYSTEM ENTER TD ENTER Chain Selects the preferred chain The default setting is 9970 Pair Selects the pair of stations in the selected chain The default setting is W X ASF 1 2 Sets the ASF Additional Second Factor for the slave in the selected chain The default setting is 0 Alter Turns On Off the Alternate Solution in the chain The default setting is Off 5 3 2 FIX DATUM Sets the datum reference used by the
118. pare 3 Lo iegg Ship s coordinates EEE COG Course Over Ground Date and time E 0 elevation C 45 elevation D 90 elevation Bars to indicate IN Ratio Tracked but not Horizontal dilution of used Satellite precision Index for position fixing Speed Over Ground accuracy C Over Ground Vertical dilution of EE D Kts ALT Ft HDOP 12 5 precision Index for 0 T VDOP 33 2 SB position fixing Altitude Ed gt accuracy Fig 3 1 3 GPS Status page H On the right side of the screen see Fig 3 1 3 there is a polar representation of the azimuth and elevation of each satellites The circle contains a number indicating the PRN of the satellite and it is filled when it is used for the fix solution On the lett side there are histograms indicating the S N ratio SNR The bar is filled when the satellite is used for solution As example the satellite with PRN 10 is used for solution with N 44 Azimuth 127degree and Elevation 70degree When a valid fix is received the Lat Lon Date Time Altitude VDOP HDOP SOG and COG are shown in the page 3 1 4 NAVIGATION DATA PAGE The Navigation Data page shows information about speed SOG and course COG of the ship status of the received signal ship s coordinate and other general information Total and Partial distance traveled by the sik from the first x 44 00 m AST activation of the chartplotter or starting from the values reset zer AA Om
119. point navigation follows the next point if exists When Target is set three options are available STOP NAV NEXT and PREV 4 5 USING THE TRACK FUNCTIONS As long as the chart plotter is connected to a positioning instrument it stores all points in its memory The chart plotter can store a fix when the distance from its last stored position 1s greater than a defined distance or after a defined time A line connects such W SC eer Manual points and represents the past course called the track of the ship gt MENU ADVANCED SETTINGS ENTER TRACK ENTER 4 5 1 SELECTING ACTIVE TRACK gt MENU ADVANCED SETTINGS ENTER TRACK ENTER ACTIVE TRK ENTER Select the number of the active track The default setting is 1 4 5 2 ENABLING TRACK STORING gt MENU ADVANCED SETTINGS ENTER TRACK ENTER TRACK ENTER To enable On or disable Off the track storing It is not possible to use the track storing if you ate not receiving a valid fix The default setting 1s On 4 5 3 DISPLAYING TRACK gt MENU ADVANCED SETTINGS ENTER TRACK ENTER VIS IBLE ENTER To enable On ot disable Off the displaying of track The default setting is On 4 5 4 SELECTING TRACK COLOR gt MENU ADVANCED SETTINGS ENTER TRACK ENTER COLOR ENTER Selects the desired color among the eight colors available for the track 4 5 5 DELETING TRACK
120. rence points related to cursor position E MOBILARM Automated crew monitoring system dedicated to monitoring onboard crew by maintaining a constant link between the crew member and the boat The instant a man ovet board event happens an automatic alarm is sounded and the vessels position is logged E Natural Features Any topographic feature formed by the action of natural processes coastlines relief glaciers User Manual o Y FG E Navigate mode Operating mode called also Home mode all operations refer to the ship s position E NMEA 0183 The NMEA 0183 Data Interface Standard was developed by the National Marine Electronics Association of America It 1s an international standard that enables equipment from many different manufactures to be connected together and to share information m Pictures and Diagrams The MAX data format allows assigning one or mote image to any cartographic object These Pictures are typically used to facilitate the identification of cartographic objects or places around the map they can be the landscape layout nearby a harbour the shape of a bridge or of a buoy etc On some objects such as bridges the image associated can represent the Diagram representing the shape of the objects and the various charac teristics length height type of bridge etc e SST CSR a E Wwe M I gn D en FP EN De Fig A 1 Pictures and Diagrams E OSGB Ordnance Survey of Grea
121. rget icon is moved on the new cursor position 4 1 1 6 Moving Waypoint gt Select Advanced Mode Place cursor on Waypoint Press ENTER Select MOVE and press ENTER Use the cursor key to move the cursor a dotted line connecting the Waypoint to the new position is shown Secche Di vada K POSITION 43 08 880N E SOG Kts COG M DST Nm BRG MM 19 60 079 MAP DATUM WGS 1984 Bs MPT OA Fig 4 1 1 6 Moving Waypoint function 1 To place the Waypoint in the new position choose the new place and press ENTER CLEAR otherwise Waypoint appears in the new position 620 SC eer Manual Secche Di ia ep OSS gt i POSITION PARZ 43 08 899N 009953 757E K SOG Kts CoG H DST Nm BRG M 19 32 094 MAP DATUM WGS 1984 A y 6 LIPTAA Fig 4 1 1 6a Moving Waypoint function II 4 1 1 7 Inserting Waypoint Every time you place the cursor on the segment connecting two existing Waypoints of a route the following function 1s available gt Place cursor on route leg Secche Di DAOR vada A 4 d POSITION FROM WPTOO1Z TO HP T002 for options ee i 13 99 064 Capraia HPTOGE MAP DATUM HGS 1984 3 mH MIPTAAP SNm Fig 4 1 1 7 Placing Waypoint between two existing ones 1 Press ENTER Select INSERT and press ENTER The line between the two Waypoints is turned into a dotted line move the cursor to the new position When the c
122. roved over the next years to expand the area of coverage increase the availability of precision approaches increase signal redundancy and reduce opera tional restrictions E Waypoint Any point to which one intends to navigate sequence of Waypoints makes up a Route plan E WGS 84 World Geodetic System 1984 Coordinates System or Datum developed by the Defense Mapping Agency DMA E Zoom In Shows more detail in a smaller area E Zoom Out Operates similarly to zoom in but in the reverse showing a wider but less detailed view E XTE Cross Track Error The distance from the ship s present position to the closest point on a line between the origin and destina tions Waypoints of the navigation leg being travelled 126 CS ee Manual Analytical Index 3D Navigation Data page 16 33 EE ee 15 A PET Dyre 20 A B C D function rerrnnrernnrr 16 38 75 About Page eege 106 116 Activation Range ssesesseeeeeees 97 98 Active Target EE 97 active TEE 77 Add to e tt 72 74 Adding Event E 73 Adding Way PO EE 60 Advanced Functions rrrrrnrrrvrrnnrrennnnr 34 Advanced Mode 34 59 62 75 121 Advanced Settings A 87 EE 16 95 121 AIS MEN en 97 AIS NMEA message rnnnnnnnnnnnnnnnnnnnnnr 98 AIS SymDOlS EE EN 97 PN EE 92 96 118 Alarm Report sansen 94 Alarm Status si 108 Alarms leese tee cant 17 Altitude Lese Maud De 95 T21 Altitude Unit vanene 17 Anchor Alarm ar
123. rrrnnnnnnnserennnrrrnnnssnnnn 112 6 4 2 Autopilot ENN urene 113 6 4 3 External NMEA Connections A 114 6 4 4 C COM Conedbhuuueseseassgsssdsmvkanana gne 114 6 4 5 External Alarm Connection annnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnonnnnnnnnnnn 114 6 6 TROUBLESHOOTING scscncccncsotcsnnnacdueennacundsausentesasedant secuinteeeencsdweanadensey 115 6 6 1 Problems and Solutions 2 0 0 ccceececececeeeeseeeesseeeeeeesesseeeeeseeeeees 115 6 6 2 Quick Reference Guide rrrrrrrrrarnarornnnnnnnnnnnnnnrnrrrvnvnnvnnnenennensnsnnn 115 6 6 3 If you need assistance arsen EE eegend 115 6 6 3 1 World Background Charts es eegeeettegedtee eege eege 116 Worldwide Background Update nennnnnnvnonnnrnnnnnnnn 116 User Manual O7 HR RR EE 116 6 7 1 RAM WGI EEN 117 6 7 2 DONN 117 SEE tele 117 Br DEE e 118 6 7 5 External AlarM EEN 118 6 7 6 Display Settings EE 118 A Tee EEN 121 Anahucalindex pekes 127 User Manual 11 Introduction Congratulations on your purchase of the chart plotter If you have not used a position finding instrument before and intend to use your chart plotter for navigating we suggest you should read this User Manual and make sure you ate familiar with its contents The User Manual is divided into three main parts Chapter Before You Begin introduces you to the basic information to get you start using the chart plotter Chapter For the New User should be read first to become familiar with your new instrument
124. s MOB and on MAGNUM Pro EVENT for 2 sec onds select CANCEL and press ENTER again The MOB symbol remains on the screen shaded until the next screen redraws Note If the Advanced Settings item in the menu Basic Settings is activated On placing the cursor on MOB the information window appears as shown in the previous Fig 5e Press ENTER select CANCEL and press ENTER again the MOB symbol remains on the screen shaded until the next screen redraws WB CS eer Manual For the Experienced User Now you have had a chance to became familiar with your new chart plotter there are a great number of advanced features that you will find helpful First of all the use of the Advanced Mode The chart plotter can operate in two different modes Basic Mode and Advanced Mode In the first mode there is a restricted number of functions while in Advanced Mode itis possible to have more available functions for example it is possible to handle Waypoints To select the Advanced Mode gt MENU BASIC SETTINGS ENTER ADVANCED FUNCTIONS ENTER ON ENTER When Advanced Functions is Off the chart plotter operates in Basic Mode 4 1 MORE ABOUT CREATING AND USING ROUTES At anytime you may add or delete Waypoints see a route summary reverse the direction of the route or erase the entire route 4 1 1 WAYPOINT You may add Waypoints delete Waypoints from a route move any Waypoint in the route to another locatio
125. side settings 3 5 1 6 Dynamic Nav Aids gt MENU MAP SETTINGS ENTER Dynamic Nav Aids ENTER This function allows settings blinking lights on Nav Aids The blink period and color of each Nav aid is read from the Nav Aid attributes available on the data cartridge When the ship is inside the Nav Aid nominal range the light of the Nav Aid will start blinking The default setting is Off When Dynamic Nav Aids option is set to On when the flashing light is Off or when fix position is out of the sector the light color is displayed by using a faint light color 3 5 1 7 Mixing Levels gt MENU MAP SETTINGS ENTER Mixing Levels ENTER When the map coverage at the current zoom level does not fill the entire screen the chart plotter draws the rest of the map expanding the cartographic information read from at most two zoom levels above the current zoom level For this reason the map is drawn three times firstly 1t draws the two levels before the current level and then the current level The area covered by the cartographic data read from the previous levels is identified by a dotted pattern When the cursor 1s moved on an atea not covered by data of the current level the chart plotter zooms out to the first level covered by cartographic data The default setting 1s On User Manual EF Note The Mixing Levels function works only with the new C CARDs It also affects the speed of the redraw of the screen If this
126. ssel that a target may reach before a target is deemed a threat CPA Alarm Occurs if CPA is less or equal to CPA Limit This test is done fot active targets only TCPA Time to closest Point of Approach is the time remaining until the CPA will occur TCPA Limit This is the time remaining before the CPA is reached TCPA Alarm Occurs if TCPA 1s less or equal to TCPA Limit This test is done for active targets only and if CPA value is less or equal to CPA Limit Radio Call Sign International call sign assigned to vessel often used on voice radio Name Name of ship 20 characters MMSI Maritime Mobile Service Identity MMSI number unique H digit number that is assigned to a DSC radio station It primarily regis ters the boat information in the US Coast Guatd s national distress database for use in emergency situations User Manual Active Target Target located within the Activation Range Active target is represented by oriented triangle with COG and Heading vectors Rate of turn may also be displayed Dangerous Target Target detected by CPA or TCPA Alarm Dangerous target 1s Active Target by definition For better visibility Dangerous Target symbol is flashing Sleeping Target Target located outside the Activation Range Sleeping target is represented by a small oriented triangle Lost Target When the AIS info is not received from that vessel for 3 5 minutes The presenta tion will be a flashing black triangle
127. ssing MENU For more information see the specific User Manual Note The Radar display page is available only if the Radar is connected and powered On 110 Uer Manual 6 Z COA LAN M VID 1 2 49 7 2 gt lt gt 30 5 LS 0 STI INSTALLATION For the Technician 6 1 DIMENSIONS i 6 2 111 User Manual 6 3 EXTERNAL WIRING AUX IN I O CONNECTOR CABLE PIN WIRE COLOR FUNCTION GND COMMON POWER OUTPUT 10 35 Vdc ONER DEE PIN FUNCTION GND OUTPUT 5 OUTPUT 4 INPUT 5 EXTERNAL ALARM OUTPUT HSYNC VSYNC N C BRIGHTNESS CONTROL WO OIN DUA JW N e SMART GPS SENSOR pr POWER amp I O CONNECTOR CABLE PINIWIRE COLOR FUNCTION GND COMMON GPS CONNECTOR CABLE POWER INPUT 10 35 Vdc PINIWIRE COLOR FUNCTION INPUT 1 POWER OUTPUT 10 35 Vdc GND OUTPUT 3 OUTPUT 2 INPUT 3 OUTPUT 1 INPUT 2 EXTERNAL ALARM OUTPUT BLACK YELLOW SHIELD GND SIGNAL RETURN NOTE Add in series to power cord both Red and black wire a 1A Fuse supplied POWER SUPPLY 6 4 TYPICAL CONNECTIONS Power amp I O Connector 6 4 1 GPS CONNECTIONS SMART GPS SENSOR POWER SUPPLY POWER amp I O CABLE PIN WIRE COLOR FUNCTION GPS SENSOR CABLE PWR GND
128. stance unit is selected by the user see Cap 5 The default setting is 0 01 Nm 4 5 9 SELECTING TIME gt MENU ADVANCED SETTINGS ENTER TRACK ENTER TIME ENTER When the tracking function is On and the type of track storing 1s Time the chart plottet can store a fix after a defined time Choose among 1 5 10 30 sec 1 5 10 min The default setting is 1 sec 4 6 USER C CARD MENU The chart plotter allows to copy information to an User C CARD You can also return the information to internal memory at a later time This allows virtually unlimited storage gt MENU ADVANCED SETTINGS ENTER USER C CARD ENTER Number of Selected Slot USER C CARD Date and Time of file creation JILE G TRACKS D OG OG l FILE 2 i MARKS e 66 00 00 File name FILE 7 TRACKS 60 00 00 FILE 4 i MARKS i 66 00 00 JILE 71 I TRACKS GILE S TRACKS Ng GJLE 7 TRACKS 1 01 80 I Borgo FILE S i MARKS 87 02 98 FILE S ROUTES I 07 02 98 i FILE 1 TRACKS 1 01 80 FILE 3 i MARKS 1 1 8 00 00 TRS FILE S MARKS 1 01 80 00 00 00 Number of Selected file WETS RIES dE Type WAS hie Waypoint fie Fig 4 6 User C CARD Menu WB Use Manual 4 6 1 SAVING FILE gt MENU ADVANCED SETTINGS ENTER USER C CARD ENTER SAVE ENTER A window is opened to insert the file name and the type of data to save USER CARD SLOT
129. surface of the earth E Default Indicates a value or a setting which 1s used if the user has not defined a particular value You can modify this value using the menu settings E Depth Area Range The sea area that 1s beyond the selected range 1s filled by an uniform white color the sea area that is inside the selected range is filled by ordinary multicolor shading The Spot Soundings and Depth Contours are displayed on the range only E Depth Lines Imaginary lines connecting points of equal water depth E DGPS Differential GPS Provides even greater positioning accuracy than standard GPS E DSC Digital Selective Calling Method of establishing a VHF radio call it is used to announce urgent maritime safety information broad casts This system allows mariners to instantly send Distress Call or and Position Request to the other vessels equipped with a DSC transceiver within range of the transmission 122 User Manual E EBL Electronic Bearing Line Dotted line with direction selectable by the user E Event User Point that refers to the ship s position It is simply a way of marking where the boat is E File Collection of information of the same type stored on a User C CARD Each file must have a unique name ideally one that describes its contents Filenames are kept in a directory on each User C CARD E Goto Sets a particular mark on the map called Target or Destination E GPS Global Positioning System Satellite based nav
130. t press ENTER to set the date and time manually MENU to decrease time and GOTO to increase time Press CLEAR to exit 3 5 1 11 Other Map Configurations gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER This function allows the user to customize the following selections and is divided into the following settings Marine Settings Depth Settings Land Settings and Chart Settings Display Mode To simplify the customization of the chart display the map settings are now fe organized in modes allowing the user to choose the preferred setting Pre pto grammed settings are user selectable from Full Medium Low Radar Tides Custom The default setting is Custom gt MENU MAP SETTINGS ENTER Other Map Configurations ENTER Display Mode ENTER The table below shows the selections for each mode User Manual oo Setting Full Medium Low Radar Tides Custom Default values Names On On On On On On Name Tags On Off Off Off Off On Nav Aids amp Light Sectors On No Sector No Sector No Sector Off On Attention Areas On On Off Off Off On Tides amp Currents On Off Off Off On On Seabed Type On Off Off Off Off On Ports amp Services On On Off On Off On Tracks amp Routes On Off Off Off Off On Depth Range Min OMt OMt OMt OMt OMt OMt Depth Range Max 9999Mt 9999Mt 9999Mt 9999Mt 9999Mt 5Mt Land Elevations On On Off Off Off Off Land Elevation Values On Off Off Off Off On Roads On Off Off Off Off On
131. t Britain Coordinate system describing only Great Britain Generally used with GBR36 datum which also describes only Great Britain This coordinate system cannot be used in any other part of the world E Port Info The Port Info function is a combination of a Port Info database containing all the relevant Safety and Navigational information normally found in good pilot books and a presentation software which displays special Port Facility Symbols E Ports amp Services Areas along shore with facilities for mooring downloading and uploading of ships generally sheltered from waves and winds Port installations are piers wharves pontoons dry docks cranes E Route Sequence of Waypoints connected by segments Among the available Routes only one is the active Route which is shown by a straight line and arrows to indicate the direction E RICM Radio Technical Commission for Maritime Services The data format created by the Radio Technical Commission Maritime to transmit Differential GPS corrections E SOG Speed Over Ground Calculation of the rate of movement of the ship over the ground E Speed Current velocity at which you ate travelling relative to a ground location E Spot Sounding Depth of the water in a specific and charted position E STR Steering Difference between COG and CTS If COG is 25 and CTS is 30 then STR is 5 Right E Target In order to tag on the chart the point towards which the ship is Heading yo
132. t1 Port2 ENTER W User Manual 3 2 8 6 C Link Selects the Master unit Primary Station ot the Slave unit Secondary Station gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER C LINK ENTER Secondary Station Primary Station ENTER 3 2 8 7 External Signal Sets the External Output Then choose your preferred setting among External Alarm when activated this pin goes to GND level It is used to command an external buzzer External Power it is command switch for the Radar It must be used in conjunc tion with the Radar Junction box device and Off gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER EXTERNAL SIGNAL ENTER 3 2 8 8 Cable Wiring Pages Shows a window containing the interface cable wiring See Par 6 3 and 6 4 MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER POWER I O CABLE WIRING ENTER MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER GPS CABLE WIRING ENTER MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER AUX IN I O CABLE WIRING ENTER 3 2 9 C VOICE MENU AVAILABLE ONLY IF THE CHART PLOTTER IS CONNECTED TO VOICE NAVIGATION SYSTEM The chart plotter has two different vocal modes Navigation and Echosounder According to what mode is selected the messages spoken from the chart plotter are different gt MENU BASIC SETTINGS ENTER C VOICE ENTER 3 2 9 1 Navigation Enables On
133. ter has to be setup to be able to receive NMEA information from the MOBILARM When a MOBILARM is connected to the chart plotter any input port of the NMEA Input Output menu must be changed to MOBILARM as shown below for communications gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER se lect any input port you want ENTER MOBILARM ENTER The chart plotter continuously verifies the communication status with MOBILARM instruments If there is no communication for more than one minute an alarm window appears 5 11 2 MOBILARM STATUS If you want to know information about the MOBILARM connected follow the procedure gt MENU About ENTER User Manual 105 CHARTING OPERATING SYSTEM Copyright C 2008 JEPPESEN Italia S r l Software XXXX V X yy R GG MM YYYY NTSL v7 0 8 49 R 22 06 2007 1 KERNEL v1 37 0 R 29 10 2007 1 FILE SYSTEM 3 21 0 R 15 01 2007 1 BIOS 1 4 22 M 29 03 2007 1 GPS Generic FF library v1 26 00R 19 11 20071 FF module BBFF 507200 RADAR library 1 19 00R C20 11 20071 RADAR module S N 655351 C HEATHER 1 14 00 R 26 10 2007 1 C CARD 1 EM B954 66 LIGURIAN HIGH TYRR AND C CARD 2 No C CARD User Points Routes Track Points Tracks 5 MOBILARM Connected wa to System Update Fig 5 11 2 Example of About Page In the About Page a new item appears related to MOBILARM status where status can be Function Not Activated MOBILARM input format has not been s
134. this function press ENTER using the cursor select SHOW and press ENTER to close all menus data pages if open and center the chart on the received PTX 5 12 FISH FINDER MENU The chart plotter combined with the sonar performance of the Fish Finder is one of the most advanced marine navigation system available gt MENU FISH FINDER SETUP ENTER ONLY ON MAGNUM Pius gt ECHO for 1 second To select the Fish Finder pages gt lt PAGE gt cursor keys ENTER to select the desired Fish Finder page ONLY ON MAGNUM PLus gt ECHO For more information see the specific User Manual Note The Fish Finder display page is available only if the Fish Finder is connected and powered On User Manual 109 5 13 RADAR SETUP MENU The Radar consists of a scanner unit which illuminates targets with microwave energy and then collects the echoes from those targets The scanner unit includes the Radar antenna transmitter receiver and necessary electronics The scanner unit is connected to a chart plotter equipped with software capable of displaying the Radar functions To select the Radar menu first select one of the four page related to the Radar gt MENU RADAR SETUP ENTER ONLY ON MAGNUM PLus gt RADAR for 1 second To select the Radar pages gt lt PAGE gt cursor keys ENTER to select the desired Radar page ONLY ON MAGNUM Prus gt RADAR Once the Radar page ts selected access the Radar menu by pre
135. u can use a special mark called 1240 CS se Manual Target When the Target is placed all navigation data are referred to this Target E TD Time Difference Loran positions are determined by precise timing of the intervals between reception of pulses transmitted by pairs of stations in the selected chain Between any two stations a ship must be located somewhere along a line of possible positions where the measured Time Difference TD between arrival of pulses from those stations would be observed The TD is measured from the time of reception of the master station signal to the time of reception of the slave station signal E Tide Periodic rise and fall of the surface of oceans bays etc due principally to the gravitational interactions between the Moon and Earth E Tide Info Combination of a tide heights database that will be included within C CARDs and features which calculate the tide graph for all primary and secondary ports worldwide This function can calculate the tide heights for any past or future date and as a by product of this calculation will also display the Maximum and Minimum Tide height and time for the day selected plus the times of Sunrise and Sunset At some chart levels the chart plotter will display a new Tide Diamond Symbol for every Port or tide point in the database covered by that particular C CARD m Tide amp Currents The worldwide database with tidal stream information is available with MAX C CARDs Whe
136. ual 7 4 4 2 DELETING THE A B C D POINTS When placing the cursor on the desired point A B C or D the information window appears Press ENTER select DELETE and press ENTER again the point is deleted When the point is deleted the cursor is placed on the previous point if existed The labels of the next points are renamed 4 4 3 DELETING THE A B C D SEGMENT When placing the cursor on the desired point A B C or D or on segment between two points the information window appears Press ENTER select DELETE ALL and press ENTER again all points and connecting segments are deleted 4 4 4 MOVING THE A B C D POINTS When placing the cursor on the desired point A B C ot D the information window appears Press ENTER select MOVE and press ENTER by the cursor key move the cursor on the screen a dotted line connecting the point to move with the new position appears By pressing ENTER the point is placing in the new position 4 4 5 INSERTING THE A B C D POINTS Placing cursor on the segment connecting two points the information window appears Select INSERT and press ENTER by the cursor key move the cursor on the screen a dotted line appears By pressing ENTER the new point is placing between the two existed points which are renamed 4 4 6 NAVIGATING ON THE A B C D POINTS If fix received is good place the cursor on the desired point A B C or D and press DEST When ship teaches the Destination
137. up down the cursor key to select the User Point you wish If the page contains more than 8 User Points the list continues in the next pages See Par 4 1 1 9 4 2 1 7 Add to route Select Advanced Mode Place cursor on Mark Press ENTER Select ADD TO ROUTE and press ENTER the selected Mark is connected to the current route The same Mark can be added in many routes Note An existing Mark can be connected to the current route in another mode too Place cursor on Mark the information window related to the Mark appears press CT E ART to close the window and then press ENTER select the Waypoint option and press ENTER The Mark is connected to the current route 4 2 2 EVENTS In Navigate mode you may place a location with an Event symbol and number directly on the ship s position Move the cursor to exit from Navigate mode place the ToC ee Manual cursor on an Event to access the following functions 4 2 2 1 Adding Event ONLY ON MAGNUM Pius Select Advanced Mode CLEAR then ENTER EVENT ENTER Of gt Event if it is present ONLY ON MAGNUM Pro gt CLEAR EVENT An Event is placed directly on the ship s position 4 2 2 2 Deleting Event gt Place cursor on Event Press ENTER Select DELETE and press ENTER the Event remains on the screen shaded until the next screen is redrawn Note If you try to delete a Event that belongs to many routes the chart plotter e
138. urchased from e External bracket kit e AUX IN I O cable 1 5 mt 5 9 feet 2 Fuses I Amp fuseholder I O cable CBCOFS0603 e Power supply and I O CBCOFS0804 e Video Cable CBCHMS0700 e User Manual C MAP By Jeppesen C CARD cartography data cards are available through your local dealer For additional information on C MAP By JEPPESEN Cartography visit web site at www jeppesen com 1 2 1 SPECIFICATIONS 1 2 1 1 Main Characteristics Recordable Individual points User Points 1000 Type of User Points 16 Routes Routes lt 20 Max Uset Points per Route e 100 Tracking Tracks Points per Track 5000 Step by Distance Q01005 0105 1 27 5 len Step by Time 1 5 10 30 Sec 1 5 10 Min Cartographic Functions Detailed Map by using C MAP By Jeppesen C CARD e C MAP By Jeppesen MAX electronic charts object oriented chart system with en hanced functionality including Guardian alarm Safety Status Bar Safety route check 4 User Manual Perspective view Satellite image coverage Turbo and Smooth Zoom Multilanguage Enhanced Port information database Tides amp Currents data Photos amp Diagrams Automatic information on all chart objects Search function for ports tidal information service facilities Coordinate System ddd mm ss ddd mm mm ddd mm mmm UTM OSGB TD e Map Datum Display Mode Full Medium Low Radar Tides Custom Marine Settings Names Name Tags Nav Aids amp Light Sectors Attentio
139. ursor is stationary for one second or two the line will rubber band drawing a dotted line between the last Waypoint and the cursor and another dotted line between the cursor and the next Waypoint T Secche Di A mr Vada Al be X d POSITION 43 08 938N 009 S3 757E SOG Kts CoG M am mm e m a e e D TT M 19 118 067 MAP DATUM WGS 1984 ws 6 Fig 4 1 1 7a Placing Waypoint between two existing ones II User Manual Once you have positioned the cursor at new location press ENTER press CLEAR to abort operation t A h Secche Di u AN amp l Vada i POSITION tye a A 43 08 957N IW 009 S3 757E T d f S0G Kts COG M VK d HPTOGS WPT aa2 La WPT 96 000 DST Nm BRG M 5 276 MAP DATUM WGS 1984 SCALE ae p UPTAAZ SNm Fig 4 1 1 7b Placing Waypoint between two existing ones II GW 4 1 1 8 Editing Waypoint Select Advanced Mode Place cursor on Waypoint Press ENTER Select EDIT and press ENTER to modify a Waypoint A win dow will be shown with Name Symbol Color and Latitude Longitude of the Waypoint advising about what Waypoint data are modifiable Secche Di AL OG 7 a POSITION 43 08 976N 009 S3 757E mmm mm mm mm oe es E SoG Kts COG M S DGiluzae 43 12 549N M pes 18 85 079 e Sp
140. vrnrvnnrnvnnnnnnnnnnnnvnnevanener 17 PE 36 Arrival Armand 17 Arrival TIME Lue 121 DF 90 ASS St ANCE en 115 Attention Areas rrrvrrnnnrennn 15 46 121 Automatic Info E 16 49 te ei og EE Ramer ey reer 23 Autopilot Connections xxrrnrvn 23 113 AUX IN W O cable Lunner NONE 14 Auxiliary Memory ege ee 17 EE 33 EN detects 33 PU 32 121 B Background C CR 117 User Manual Ba 16 EN 117 Basic Mode 34 59 62 121 Basic Settings E 33 PAN GUC urnen 40 Gel EE ee enn ere eee ae 121 PE eri 61 121 Bearings Magnetic rrrrrernnvvnnennnnnnrnnenn 16 Bearings True varen 16 EP 36 BP Gee ene anne ee enrene ee nr aerial 121 le 121 Buoys and Beacons nnrnnnnnnnvovovnvennn 121 EV 36 88 C ETR 14 26 117 C CARD Connector s ssssseseesseeeeeeeeenn 118 SENDE 117 GO ene sane eee nee arene ene ane 25 114 C COM Connection rernnrrrnnnnnrr 25 114 GE apeemeone renee reenter 16 37 80 81 C Link Navigation Data 81 84 C Link serial CONNECTION eee 82 C MAP G GARD E 14 C MAP cartridges cscsccceeeeeees 26 Ge AAA E 16 99 ONC ee 37 C Weather EE 21 C Weather Service rrrnrrnrnnnnererrerrenr 16 Cable Wiring Pages rrrrrrnrvnvrvrrrrrenr 37 Cartographic Data uunsunnmmnmenssnk 41 Cartographic Functions mesen 14 CARTOGRAPHY INFORMATION 40 CANO GCS EEE 117 Caution NEIE ee geet Ee ee 22 GE EE 90 121 Changing User C CARD rrrnvrrvererrerr 80 Chart
141. with a cross through Activation Range Range around your boat where targets become active AIS target become active within this range Activation Range should be greater than CPA Limit by definition Note A target is removed from the screen if data is not received for 10 minutes The maximum number of tracked targets is 200 Depending on the scale the presentation of the targets change to remove clutter on the screen This information 1s updated every 3 seconds to 6 minutes depending on speed and rate of turn enabling the track of the vessels in range to be plotted TARGET STATUS DESCRIPTION SYMBOL ACTIVE TARGET Target located within the Activation Range Target detected by CPA or TCPA Alarm CA Dangerous Target is Active Target by definition Flashing DANGEROUS TARGET SLEEPING TARGET Target located outside the Activation Range A LOST TARGET Ais info is not received from that vessel for 3 5 minutes A Fig 5 7 1 AIS Symbols 5 7 2 AIS MENU To configure the chart plotter to receive AIS data follow the procedure gt MENU AIS SETUP ENTER The AIS menu is shown on the screen the items are described in the following paragraphs 5 7 2 1 Display gt MENU AIS SETUP ENTER DISPLAY ENTER Turns the display of AIS targets overlay on the cartography ON or OFF The default setting is ON User Manual WT 5 7 2 2 Activation range gt MENU AIS SETUP ENTER ACTIVATION RANGE
142. xample to set the Port 2 as NMEA 0183 4800 Baud Rate Parity None 8 Bits Number 1 Stop Bit and Normal Polar ity you must select gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 1 2 3 4 5 INPUT ENTER Choose your preferred setting and press ENTER to confirm Note The port selection for C COM or BBFF Fish Finder system defines on which Port in Input or Output are to be connected the two systems It is important to remark that this setting affects the Input and the Output of the selected Port If the C COM or BBFF Fish Finder was already assigned to one Port and the user tries to set the C COM or BBFF Fish Finder to another port the chart plotter will show a message that warns the user about the current settings and asks if the new settings should overwrite the previous ones User Manual 31313137 35 3 2 8 2 Port 1 Port 2 Port 3 Port 4 Port 5 Output Sets or disables the output interface The default setting is NMEA 0183 4800 N81 N gt MENU BASIC SETTINGS ENTER INPUT OUTPUT ENTER PORT 1 2 3 4 5 OUTPUT ENTER 3 2 8 3 Port 1 Port 2 Port 3 Port 4 Port 5 NMEA Output The chart plotter allows customizing the NMEA 0183 sentence transmitted on each port Each port can transmit a different set of sentences among GLL VIG BOD XTE BWC RMA RMB RMC APB WCV GGA HSL HDG The default setting 1s GLL VIG XTE RMB RMC APB On and BOD BWC RMA WCV GGA HSL
143. you try to move a Mark that belongs to many routes the chart plotter emits three beeps and on the screen a Warning message appears If you want to move the Mark press ENTER 4 2 1 5 Editing Mark gt Select Advanced Mode Place cursor on Mark User Manual 7 Press ENTER Select EDIT and press ENTER A window appears to modify Name Symbol Color and coordinates of the existing Mark BE POSITION 4 4 d 1 1 H MARK 43 09 161N d 009 53 757E K rpkaes H SOG Kts CoG M LL 000 43 48 016N TO CURSOR DST Nm BRG M MAP DATUM WGS 1984 SCALE ki 2 NM Fig 4 2 1 5 Edit Mark Use the cursor key to select the field If you have selected Name field press ENTER use the cursor key to insert the character 8 characters max then press ENTER If Symbol field is selected press ENTER a window with 16 different symbols appears Use the cursor key to select the symbol and press ENTER If Color field is selected press ENTER a window with 8 different colors appears use the cursor key to select the desired color and press ENTER If Coordinates field is selected press ENTER and then use the cursor key to insert the value Then press CLEAR 4 2 1 6 Finding information on Marks User Points List page gt MENU ADVANCED SETTINGS ENTER USER POINTS ENTER A full window is opened showing information about all stored User Points Marks Events and Waypoints Move
144. your dealer sg Fig 2 5 2 Removing C CARD 2 6 MENU OPTIONS You may select how the chart plotter displays primary information such as how time is displayed from the Functions Menu gt MENU Refer to Chapter 5 for more information on Main Menu 2 7 DATA ENTRY Information is keyed into the chart plotter when editing a Waypoint entering a Route or using the Fix Correction functions When the field 1s highlighted Enter or edit data by pressing up down cursor key to step through the available characters until the preferred character 1s displayed User Manual DDT 28 Press right cursor key to move the cursor to the right Use left cursor key to move the cursor to the lett User Manual For the New User In order to get started using your chart plottet you must do the following things 1 Your chart plotter must have been installed properly according to the installation instruction on Par 6 2 2 You must have performed the proper settings for use with your positioning instrument see Par 2 4 and inserting the C CARD for navigating in area you wish see Par SC 3 You must have turned on the chart plotter and adjust the brightness and contrast of the display see Par 2 2 Once this is done you can use your chart plotter for navigation 3 1 SCREEN DISPLAY CONFIGURATION Use PAGF to select the desired page in two different ways 1 by showing the next page as the relative k
145. ytime a Waypoint is added inserted edited or moved Before activating the function you could change the function parameters as the width and the depth of the detected area and the research accuracy To select the width of the detected area aside the route gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE WIDTH ENTER Note Safe Route width value represents half the total width checked by the function User Manual 69 To select the depth of the detected area aside the route gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER ROUTE DEPTH ENTER It also possible to select the accuracy for the route check among Very Low Low Medium High and Very High gt MENU ADVANCED SETTINGS ENTER ROUTE ENTER AC CURACY ENTER 4 2 MARK amp EVENT You may place a Mark as it 1s called at your cursor position while Event is created at yout vessel position 4 2 1 MARKS You may tag a location on the chart with a Mark symbol and number which you can record for later use Every time you place the cursor on a Mark the following functions ate available 4 2 1 1 Adding Mark ONLY on MAGNUM PLus gt Select Advanced Mode ENTER MARK ENTER ot gt Marx if it is present ONLY on MAGNUM Pro gt MARK The new Mark appears on your cursor position An info window containing Mark name symbol and Latitude Longitude is shown 4 2 1 2 Delet

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents