ChassisTouch 450 Monitor User`s Installation Guide (Web)
Contents
1. 15 Controlsforadjustingthevideodisplay 15 OSD Controls s 2 5 05 0255 il lella ezeli e e 16 Maintenance and troubleshooting 19 Maintainingyourtouchmonitor 19 Care and Cle amin giyin simler ille sillmesi 19 Eroublesho tM itiiti enerig ni eatis iisk 20 Specifications standards and certifications 23 3M Touch Systems Proprietary Information V About this chapter Features CHAPTER 1 Overview This chapter presents an overview of the ChassisTouch 450 industrial monitor The topics covered in this chapter are Features of the ChassisTouch 450 monitor System requirements of the host computer Packing list for a standard ChassisTouch 450 monitor Related documents 3M Touch Systems support services The ChassisTouch 450 monitor is a flat panel industrial monitor with the following features MicroTouch Near Field Imaging NFI touch screen The NFI touch screen is durable constructed of glass reliable and can be operated with industrial gloves It calculates touches electronically by measuring disturbances in an electrostatic field near the surface of the screen The NFI touch screen comes with an anti glare and anti reflection coating Panel mountable with seal The monitor comes ready to mount in a panel When properly mounted the front of the monitor is sealed to NEMA 4X IP66 ratings Display The monitor s d2. Select AUTO in the OSD menu to auto adjust the monitor s display see Auto adjustment on page 16 Vertical noise is usually adjusted out when the display is auto adjusted If there is still noise after auto adjusting the display adjust the OSD Frequency setting 2 Press the Menu control button to call up the OSD main menu select the PC icon and then select the Frequency sub menu 3 Press the UP or DOWN control buttons so that the vertical bars of noise disappear completely or so that an even amount of noise is distributed across the entire screen To confirm a new frequency setting press the EXIT control button 4 If there is any remaining noise on the screen adjust the Phase setting see Phase on page 17 H Position V Position Selecting the H Position or V Position sub menu allows you to adjust the horizontal vertical position of the displayed image Press the UP or DOWN control buttons to adjust the position of the video image To confirm a new position setting press the EXIT control button 3M Touch Systems Proprietary Information 17 Chassis Touch 450 Monitor User s Installation Guide Sharpness Selecting the Sharpness sub menu allows you to adjust the sharpness of the video image especially when low resolutions are displayed Press the UP or DOWN control buttons until the desired sharpness is achieved To confirm a new sharpness setting press the EXIT control button Color Temperature Select
3. systems insert it in the disk drive and browse the floppy disk to find the file named setup exe Open setup exe The installation Welcome window appears 4 Follow the screen prompts to install the driver and then follow the on screen instructions of the Setup Wizard 3M Touch Systems Proprietary Information 10 Setting up the monitor 5 Follow the Setup Wizard s on screen instructions The Wizard sets the baseline for the touch screen controller downloads linearization data to the controller and aligns the touch screen to the physical display Important The ChassisTouch 450 monitor ships with the linearization data pre installed so when you are prompted to install the linearization file select Skip 6 When the Wizard finishes setting up the software an Install Successful window appears 7 For more information on how to customize NFI drivers for Windows XP and Windows 2000 operating systems see the NFI Touch Screen Software System Software User s Guide for Windows XP and 2000 The guide is available for download at www 3Mtouch com Installing the drivers for Windows NT 4 0 and Windows 9X operating systems NFI drivers for Windows NT Windows 98 and Windows 95 are available for download at www 3Mtouch com For instructions on installing and customizing these drivers see the NFI Touch Screen Software System User s Guide for Windows NT 9X 3 1 and DOS The guide is available for download from
4. by anyone other than 3M Touch Systems 3M Touch Systems shall not be liable in any action against it in any way related to the Products or software for any loss or damages whether non specified direct indirect special incidental or consequential including downtime loss of profits or goodwill regardless of the legal theory asserted Document Number 20375 Rev 2 0 April 2003 MicroTouch Near Field Imaging and ChassisTouch are trademarks of 3M Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation 3M Touch Systems Proprietary Information Intended use Safety notices Important safety information The ChassisTouch 450 monitor is intended to provide touch screen functions when connected to a host computer in an industrial setting The ChassisTouch 450 monitor is not intended for use in hazardous locations The ChassisTouch 450 monitor is a component After it is installed the whole system of which it is a part must be inspected to confirm seal ratings and compliance with all local electrical codes Product safety information N DANGER To reduce the risks associated with fire and explosion which if not avoided will cause death or serious injury and or property damage Do not install or use this product in a hazardous location WARNING To reduce the risks associated with electrical shock fire or explosion which if not avoided could result in death or seri
5. the host computer is powered off 3M Touch Systems Proprietary Information 8 Setting up the monitor b Connect one end of the video cable to the video connector on the ChassisTouch 450 monitor and then connect the other end to the video card in the host computer Figure 2 Typical host computer ChassisTouch 450 monitor OSD buttons and LED RS 232 serial touch screen cab Power supply cable AC DC power Supply Figure 2 Connecting communications and power cables c Connect one end of the RS 232 serial touch screen cable to the ChassisTouch 450 monitor and then connect the other end to an available serial communication COM port on the back of the host computer Important Be sure to tighten all cable connections Route all wiring and cabling away from heat sources and sharp metal edges to avoid damage 3M Touch Systems Proprietary Information 9 Chassis Touch 450 Monitor User s Installation Guide Important The ChassisTouch 450 monitor must be operated with the original power supply d Plug the AC DC power supply into the ChassisTouch 450 monitor Be sure to use the power supply included with the monitor A WARNING To reduce the risks associated with electrical shock which if not avoided could result in death or serious injury and or property damage Make sure that the ground potential difference between the monitor and the host co
6. www 3Mtouch com Customizing NFI touch screen drivers Energy saver The NFI touch screen driver settings that can be modified include m Sensitivity of the screen to touches m Access to right mouse button functions by touch m Response time of the touch screen to double touches For instructions on how to customize touch screen settings refer to the NFI software user s guide that is appropriate for your operating system Software guides are listed in Related documents on page 2 The ChassisTouch 450 monitor conforms to the Video Electronics Standards Association VESA Display Power Management Signaling DPMS standard To benefit from power management or energy saver the monitor must be used in conjunction with a computer and video card that implements the VESA DPMS standard 3M Touch Systems Proprietary Information 11 Chassis Touch 450 Monitor User s Installation Guide Safety recommendations If the ChassisTouch 450 monitor is used in a setting in which unintentionally activating a button on the touch screen might have harmful consequences for people or equipment 3M Touch Systems makes the following recommendations m Set System Standby to Never in the power dialog box of your Windows operating system m Do not use the Power button located on the back of the ChassisTouch 450 monitor The Power button can be used to manually turn the backlights on and off a Make the following chan
7. Colors of image Make sure that are abnormal Video cable is connected properly and securely to the monitor and the computer Nopins are bent in the video cable connector Set colors using your video driver and then auto adjust the monitor s OSD settings for details see Controls for adjusting the video display page 15 Disturbances on Make sure that the video display settings are correct see Controls the screen for adjusting the video display on page 15 3M Touch Systems Proprietary Information 21 Chassis Touch 450 Monitor User s Installation Guide NFI touch screen If you are experiencing problems with the touch screen check the following list of possible issues For a list of NFI touch screen error messages and their meanings refer to the NFI software user s guide that is appropriate for your host computer s operating system see Related documents on page 2 Touch screen bi does not respond to touch Make sure that all cables are properly connected properly Review set up procedures Chapter 2 Power down the monitor wait a few seconds and then power up the monitor again After installing the touch screen driver software restart the host computer to activate the driver Check the communication settings Is the touch screen trying to use the same COM port or IRQ as another device for example a mouse If so a hardware device conflict will result and the touch screen wil
8. EPENDABLE INNOVATIVE TOU n SOLUTIONS MicroTouch m Chassis Touch 450 User s Installation Guide 3M Touch Systems Proprietary Information ChassisTouch 450 Monitor User s Installation Guide Read and understand all safety information before installing and using this product 3M Touch Systems Proprietary Information Copyright Notice Important notice to purchaser Edition Trademarks This manual is 3M 2003 All rights reserved Reproduction of the contents of this copyrighted manual in whole or in part by any means electronic or mechanical for any purpose without written permission of 3M Touch Systems a subsidiary of 3M is prohibited Given the variety of factors that can affect the use and performance of a 3M Touch Systems Product the Product including that solid state equipment has operation characteristics different from electromechanical equipment some of which factors are uniquely within User s knowledge and control it is essential that User evaluate the 3M Touch Systems Product and software to determine whether it is suitable for User s particular purpose and suitable for User s method of application 3M Touch Systems statements engineering technical information and recommendations are provided for User s convenience but their accuracy or completeness is not warranted 3M Touch Systems products and software are not specifically designed for use in medical devices as def
9. Electrical fast transient EN61000 4 4 Surge transient EN61000 4 5 Conducted immunity EN61000 4 6 AC sags and dropouts EN61000 4 11 Electromagnetic emission standards EN55022 Class B EN 61000 3 2 Class A EN 61000 3 3 ICES 003 Class B FCC CFR 47 Part 15 Subpart B Class B CISPR 22 Class B AS NZS 3548 1995 Class B Amendments 1 and 2 3M Touch Systems Proprietary Information 27 Chassis Touch 450 Monitor User s Installation Guide Product certifications FCC B UL Information Technology Equipment United States UL Recognized C UL Information Technology Equipment Canada C Tick Australia New Zealand CE Information Technology Equipment Europe 3M Touch Systems Proprietary Information 28 3M Touch Systems 3M Optical Systems Division 800 Carleton Court Annacis Island New Westminster B C Canada V3M 6L3 www 3Mtouch com 3M 2003 Worldwide Manufacturing Plants Methuen Massachusetts Milwaukee Wisconsin Vancouver BC Canada MicroTouch and ChassisTouch are trademarks of 3M
10. Information 26 Specifications standards and certifications FCC Warning To assure continued FCC compliance the user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores If a BNC cable is going to be used use only a shielded BNC 5 cable Also any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device CE and EMC emissions compliance This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures m The ChassisTouch 450 monitor complies with the CE mark related to the Low Voltage Directive 73 23 EEC as confirmed in the Declaration of Conformity m The ChassisTouch 450 monitor complies with the CE mark related to the EMC Directive 89 336 EEC as confirmed in the Declaration of Conformity Canadian emissions compliance This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appariel numerique de la classe B respecte toutes les exigences due Reglement sur le material brouilleur du Canada Electromagnetic compatibility immunity standards Electromagnetic compatibility immunity standards EN61000 6 2 ITE immunity EN55024 Electrostatic discharge EN61000 4 2 Radiated immunity EN61000 4 3
11. X IEC 529 Degrees of Protection Provided by Enclosures IP66 FCC compliance The equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation 3M Touch Systems Proprietary
12. c shock and or burn related injury that could result in death or serious injury and or property damage Do not open the power supply for the monitor It contains hazardous voltage The power supply has no user serviceable parts or adjustments inside WARNING To reduce the risks associated with electrical shock or fire which if not avoided could result in death or serious injury and or property damage If the monitor will be used in corrosive environments it is the responsibility of the user to test and evaluate the unit in those environments The monitor as shipped has not been evaluated for use in excessively corrosive environments To panel mount the monitor and achieve a NEMA 4X IP66 seal follow these steps Important The ChassisTouch 450 monitor is designed to be mounted in a panel If you choose to VESA mount the monitor use 6 mm screws with a mounting plate that is 1 6 mm thick If the mounting plate is a different thickness adjust the screw length accordingly 1 Tape the full scale cutout template onto the panel where you want to mount the monitor 2 Using the template as your guide cut out the panel 3 Drill holes through the cutout and into the panel deburr all cuts and holes and follow the instructions that appear on the cutout template 4 Bring the power cable and the communications cable up to the cutout WARNING To reduce the risks associated with electrical sho
13. ck fire or explosion which if not avoided could result in death or serious injury and or property damage a Engineer the installation of the monitor to take into account the operating environment e g shock vibration and or thermal factors Provide a clean reliable ground To ensure compliance with electrical codes and safe operation of the monitor have a licensed journeyman electrician familiar with local codes perform all wiring and installation tasks Depending on connector depth and cabinet space you may have to make your connections at this point before installing the unit in the cutout If so skip to steps 9 and 10 and then come back come back to step 5 5 Place the monitor in the cutout aligning the studs with the holes in the panel You may need assistance at this point to hold the unit in place 3M Touch Systems Proprietary Information 6 Setting up the monitor WARNING To reduce the risks associated with electrical shock or fire which if not avoided could result in death or serious injury and or property damage If the monitor is mounted using a NEMA 4X panel gasket install the unit in a Listed UL enclosure 6 Insert the unit in the cutout until the gasket material makes full contact with the panel WARNING To reduce the risks associated with electrical shock fire or explosion which if not avoided could result in death or serious injury and or proper
14. d MS DOS are not applicable to the ChassisTouch 450 monitor Service and repair indicators Do not attempt to service this unit yourself Removing the display cover may expose you to dangerous voltage or other risks Disconnect power from the display and contact 3M Touch Systems technical support staff in the event that the monitor m Does not operate properly when the operating instructions are followed m Has been dropped or the metal enclosure has been damaged m Exhibits a distinct change in performance indicating a need for service m Has a power cable that is damaged of frayed or a power plug that is damaged m Has liquid inside its metal enclosure 3M Touch Systems support services 3M Touch Systems provides extensive support services through our website and technical support organization Visit the 3M Touch Systems website at www 3Mtouch com where you can download touch screen software and drivers obtain regularly updated technical documentation on 3M Touch Systems products and learn more about our company Whenever you contact Technical Support please provide the following information m Part number and serial number from your monitor and the serial number of the NFI touch screen both numbers are on the exterior of the monitor s metal enclosure m Current driver version m Operating system used m Information on additional peripherals Technical support is available Monday through Friday 8 a m to 8 p m US Easte
15. d firmly in the card slot in the host computer Host computer is using a supported display mode and video input from the video card that are within the range of refresh rates for the display see Table A on page 8 Is the monitor in energy saver mode Ifthe LED on the rear of the monitor is flashing orange to green to restore operation try one or more of the following Touch the screen Note If the touch screen is in a setting where safety is an issue and the recommended settings to the Display Properties dialog box have been made see Safety recommendations on page 12 a first touch to reactivate the backlights will not activate the touch screen until it is touched a second time see Testing the monitor on page 13 Press any key on the keyboard Move the mouse Are the brightness and contrast settings too low 1 Use the host computer s video driver to set brightness contrast and other video settings 2 Use the monitor s on screen display controls to Auto adjust the display settings 3 Ifthe brightness and contrast or other display settings are still not satisfactory use OSD menus and sub menus to modify display features see OSD controls on page 16 Abnormal image Make sure that Video input from the video card falls within the refresh rate of the display see Table A on page 8 Video cable is connected properly and securely to the monitor and the host computer
16. educe the risks associated with electric shock and or burn related injury that could result in death or serious injury and or property damage Do not open the power supply for the monitor It contains hazardous voltage The power supply has no user serviceable parts or adjustments inside A WARNING To reduce the risks associated with mechanical function which if not avoided could result in property damage a Do not operate the monitor in conditions outside of the operational specifications N WARNING To reduce the risks associated with skin contact or swallowing of cleaning solutions or fluids which if not avoided may result in minor or moderate injury and or cause property damage a Refer to the cleaner manufacturer s material safety data sheet MSDS and follow all instructions and recommendations on product label N CAUTION To reduce the risks associated with muscle strain which if not avoided may result in minor or moderate injury Avoid using the monitor for long periods of time without breaks CAUTION To reduce the risks associated with eye strain which if not avoided may result in minor or moderate injury Use the monitor where there is neither too much ambient light nor glare on the screen CAUTION To reduce the risks associated with environmental contamination which if not avoided may result in minor or moderate injury and or cause property da
17. em DPMS that is configurable from the display s on screen Utility menu do not turn off the DPMS 3M Touch Systems Proprietary Information 12 Setting up the monitor Testing the monitor To test that the monitor is working properly 1 Turn on the host computer A WARNING To reduce the risks associated with mechanical function which if not avoided could result in property damage a Do not operate the monitor in conditions outside of the operational specifications 2 Make sure the video image is displayed on the monitor s display If it is not visible first check to see if the LED on the back of the monitor is flashing orange to green If not press the Power button on the back of the monitor see Figure 3 on page 16 3 Ifthe LED is flashing the host computer s operating system has an energy saver setting that has timed out If you do not want the energy saver to be active and the monitor is not in a location where safety is a concern see Safety recommendations on page 12 turn off the operating system s energy saver With this setting any touch to the touch to the touch screen will activate the display and will be recognized by the controller as a touch 4 Make sure the video display is centered on the screen If it needs centering follow instructions for auto adjusting the display on page 16 If the image is still not satisfactory after auto adjusting follow instructio
18. ges in the Display Properties dialog box of your Windows operating system 1 On the host computer close all Windows applications and then open the Display Properties dialog box 2 Inthe Screen Saver tab of the dialog box choose the number of minutes that you want to elapse from the last time the screen is touched to when the screen saver will activate 3 Select the power button also located in the Screen Saver tab A power dialog box appears Important The power button is labelled differently in different operating systems In Windows XP and Windows 2000 Power In Windows 9X in the section of the dialog box named Energy Saving Features of the monitor Settings 4 In the Turn off monitor pull down menu choose the number of minutes that will elapse from the last time the screen is touched to when the energy saver will be activated The period chosen must be greater than the period you chose for the screen saver 5 Select OK WARNING To reduce the risks associated with electrical shock or mechanical function which if not avoided could result in death or serious injury and or property damage a If your monitor will be used in an environment where safety is an issue set the time for the Windows energy saver to be greater than the time for the Windows screen saver Do not use a non Windows screen saver in an environment where safety is an issue If your monitor has a display power management syst
19. ined by United States federal law 3M Touch Systems products and software should not be used in such applications without 3M Touch Systems express written consent User should contact its sales representative if User s opportunity involves a medical device application Specifications are subject to change without notice These 3M Touch Systems Products and software are warranted to meet their published specifications from the date of shipment and for the period stated in the specification 3M Touch Systems makes no additional warranties express or implied including but not limited to any implied warranties of merchantability or fitness for a particular purpose User is responsible for determining whether the 3M Touch Systems Products and software are fit for User s particular purpose and suitable for its method of production including intellectual property liability for User s application If the Product software or software media is proven not to have met 3M Touch Systems warranty then 3M Touch Systems sole obligation and User s and Purchaser s exclusive remedy will be at 3M Touch Systems option to repair or replace that Product quantity or software media or to refund its purchase price 3M Touch Systems has no obligation under 3M Touch Systems warranty for any Product software or software media that has been modified or damaged through misuse accident neglect or subsequent manufacturing operations or assemblies
20. ing the Color Temperature sub menu allows you to adjust the color balance and level of the display There are three pre set color settings Red Green Blue and an option for resetting factory default values for color User Color Reset By adjusting a single color you can make the picture look warmer biased towards red or cooler biased towards blue Adjusting all three levels will make colors appear more or less striking OSD on screen display menu Selecting the OSD icon allows you to alter how the OSD menu appears The following adjustments can be made m H Position and V Position allow you to adjust the horizontal vertical position of the OSD menu on the display m OSD Timeout allows you set how long the OSD menu will appear on the display between touches to the screen m Language allows you to choose the language used in the OSD menu and sub menus default is English IT UTILITY Utility menu The Utility sub menus that are accessible by the user are m Reset allows you to reset OSD settings to factory defaults by selecting Yes m Half Tone allows you to make OSD menus transparent by selecting Yes Neither Dynamic Brightness nor Information is configurable by the user 3M Touch Systems Proprietary Information 18 CHAPTER 4 Maintenance and troubleshooting If you have a problem setting up or using your monitor you may be able to solve it yourself Before calling 3M Touch Systems try the suggested actions that are a
21. iquid onto the cloth not the screen m Always handle the touch screen with care Do not pull or stress cables 3M Touch Systems Proprietary Information 19 Chassis Touch 450 Monitor User s Installation Guide Bezel An isopropyl or ethanol alcohol and water solution ratio of 50 50 is the best cleaning agent for your bezel Apply the alcohol solution to a cotton gauze or soft cotton cloth and then clean the bezel with the cloth Do not apply the cleaning agent directly to the bezel A WARNING To reduce the risks associated with skin contact or swallowing of cleaning solutions or fluids which if not avoided may result in minor or moderate injury and or cause property damage a Refer to the cleaner manufacturer s material safety data sheet MSDS and follow all instructions and recommendations on product label Troubleshooting If you have a problem setting up or using the ChassisTouch 450 monitor or the monitor s NFI touch screen you may be able to solve it yourself Before calling 3M Touch Systems try the strategies discussed in this chapter that address the problems you are experiencing If the problem seems to be video related you should also consult the documentation that came with the video card in your host computer WARNING To reduce the risks associated with electrical shock fire or explosion which if not avoided could result in death or serious injury and or property damage Do
22. isplay is a 15 inch active matrix Thin Film Transistor TFT Liquid Crystal Display LCD The ChassisTouch 450 monitor touch screen supports resolutions of 1024 x 768 optimal 800 x 600 and 640 x 480 pixels 3M Touch Systems Proprietary Information 1 Chassis Touch 450 Monitor User s Installation Guide System requirements The Packing list The ChassisTouch 450 monitor requires a host computer that has An available RS 232 serial communication COM port A unique interrupt request IRQ available to the COM port that the ChassisTouch 450 monitor will use The monitor cannot share an IRQ with another device A 9 pin to 25 pin adapter if the available serial port on the host computer has 25 pins A video card and video driver that is already installed For instructions on installing a video card and video driver refer to your host computer s documentation or the video card manufacturer s documentation ChassisTouch 450 monitor comes with the following items ChassisTouch 450 Monitor User s Installation Guide this manual AC power cable North American AC DC power supply 12 VDC output RS 232 serial cable SVGA video cable Full scale cutout template locknuts and washers for mounting the monitor in a panel Floppy disks with Near Field Imaging NFI touch screen drivers for Windows XP Professional and Windows 2000 Professional operating systems If your system requires Windows NT Windows 98 or Windo
23. l not work Cursor is not 7 located directly underneath your finger Align the touch screen by following instructions that appear in the NFI software user s guide that is appropriate for the host computer s operating system for available software user s guides see Related documents on page 2 Cursor is extremely jittery or erratic Adjust the refresh rate using the host computer s video driver and then use the monitor s OSD control buttons to auto adjust the monitor s display settings For more information on video settings see Controls for adjusting the video display starting on page 15 3M Touch Systems Proprietary Information 22 APPENDIX Specifications standards and certifications Enclosure and cutout dimensions 2 14 il 54 22 mm 410 00 mm TI E 12 76 12 76 324 00 mm 324 00 mm SN SN Figure 4 Front and side views of the ChassisTouch 450 monitor with dimensions Table C Enclosure and cutout dimensions Imperial Metric Enclosure 12 76 high x 16 14 wide x 324 00 mm high x 410 00 mm 2 14 deep wide x 54 22 mm deep Panel cutout 11 05 high x 14 50 wide 280 72 mm high x 368 27 mm wide Mounting 2 all around 51 mm all around clearances Weight 14 lbs 6 35 kg Panel stud length 0 63 16mm Thread a M5 3M Touch Systems Proprietary Information 23 Chassis Touch 450 Monitor User s Installation Guide Panel cutout di
24. mage Dispose of the monitor according to applicable local state and federal government regulations 3M Touch Systems Proprietary Information ii Product Safety Safety labels The following safety symbols appear on your ChassisTouch product and its packaging materials S Meaning Consult user instructions Warning Hazardous voltage A ymbol gt Caution Item is susceptible to electrostatic discharge a ESD damage if proper precautions are not taken la 3M Touch Systems Proprietary Information ili Chapter 1 Chapter 2 Chapter 3 Chapter 4 Appendix Contents GOV EMG ee sar a ela nde hiner 1 Redt resi rk in sanan Mia ilan ma e al ee 1 SystemreguiremeniS 0 eee 2 Packing liste vs 166 esate alen ei dee oe Kan kale kefe el e eote 2 Related documents airnn wc ciad eaten el islalkeliniz 2 Serviceandrepairindicators 3 3MTouchSystemssupportservices 3 Setting up themonitor e v 0000 aaa 5 Mountinggandconnecting 5 Installing NFItouchscrecendriver 10 CustomizingNFltouchscrecendrivers 11 Emir yi sav Oris ee am alanlar saza ile visne yi A eeslea 11 Testing th mohlt i sms lena all silen 13 Adjusting the videodisplay
25. mensions ot 2 N 61 01 mm 2 75 157 48 min 69 80 mm 6 20 17 00 431 80 mm 14 41 366 01 mm 14 03 356 37 mm 10 47 265 94 mm 8 5 254 00 mm 350 52 mm 438 15 mm 447 04 mm 508 00 mm 10 00 13 80 17 25 17 60 20 00 215 90 mm 6 165 90 mm 2 97 75 44 mm 2 59 65 79 mm 00 Diameter 24 6 10 mm typical Display specifications Radius 10 2 54 mm typical Operating values given are at room temperature 25 C 5 C Display size and viewing area diagonal 15 Maximum resolution 1024 X 768 XGA Type Color Active TFT Panel colors up to 16 7M Contrast ratio typical 300 1 Brightness without touch screen typical 950 cd m Brightness with touch screen typical 230 cd m Viewing angle typical H 65 V 50 to 60 Backlight life expectancy typical 35 000 hr 3M Touch Systems Proprietary Information 24 Specifications standards and certifications Chemical resistance Bezel The bezel provides resistance to user abuse and to most chemicals and other substances Touch screen The MicroTouch Near Field Imaging NED touch screen is made of glass and will withstand most chemicals and their concentrations that do not corrode glass Supported operating systems NFI touch screen drivers for Windows XP Professional and Windows 2000 Professional operating sys
26. mputer is less than 2V e Connect the power cable to the power source After connecting power the monitor will automatically power on and the LED on the back of the monitor will be illuminated for location of LED see Figure 2 on page 9 If the LED is not illuminated try pressing the Power button located on the back of the monitor If the LED still is not illuminated check that the power supply is functioning properly Installing NFI touch screen driver The Near Field Imaging NFD touch screen driver enables the monitor to work with the host computer NFI drivers for Windows XP Professional and Windows 2000 Professional operating systems came on floppy disks with your ChassisTouch 450 monitor The ChassisTouch 450 monitor ships with the linearization data pre installed so when you are prompted to install the linearization file select Skip If you ever need to reinstall the linearization file you can find it in one of two places m A floppy disk that came with your monitor m On www 3Mtouch com To download the linearization file from the web site you will be prompted to enter your NFI touch screen serial number located on the back of the ChassisTouch 450 monitor Installing the driver for Windows XP 2000 operating systems To install touch screen software for Windows XP or Windows 2000 operating systems 1 Close all open programs 2 Find the floppy disk that includes the driver for Windows XP 2000 operating
27. n Guide Table B OSD functions and locations of video controls on back panel of the monitor Name Function of the control Video controls on back of ChassisTouch 450 monitor MENU O The first press of the menu button calls up the On Screen Display OSD A second press enters the current sub menu of the OSD Additional presses allow you to cycle LED Power through the available sub menu options EXIT Returns to the previous OSD menu e 9006 O If you are at the top level this closes the es MENU EXIT UP DOWN AUTO UP Increases the value of the selected menu option Down O Decreases the value of the selected menu option AUTO Brings video settings to their optimal level OSD controls Selecting MENU will pull up the On Screen Display OSD menu as shown in Figure 3 a T sd OSD UTILITY AUTO BRIGHTNESS is 82 9 CONTRAST ee 65 El PHASE D 32 HI FREGUENCY E gt 50 ID H POSITON 4 ME o 50 ii V POSITION MAN gt 50 A SHARPNESS SHARP NORMAL Oo SOFT COLOR TEMPERATURE PRESS b KEY MENU MOVE lt gt ENTER Figure 3 ChassisTouch 450 monitor On Screen Display OSD menu Al o AUTO Auto adjustment Selecting AUTO on the OSD menu will start an auto adjustment of the monitor s video settings to their optimum level If necessary you can fine tune the parameters by selecting the PC icon and adjusting the options as explained below 3M Touch Systems Proprietary Inf
28. nitor will be used in a setting where safety is an issue Test the monitor Mounting and connecting Materials supplied 14 nylon insert hex locknuts size M5 x 0 80 14 steel washers 15 mm outside diameter 1 full scale panel cutout template 1 panel gasket already installed Note If it is ever necessary to remove the ChassisTouch from its panel mount and remount be sure to install a new front panel gasket for ordering information see 3M Touch Systems support services on page 3 Re using a panel gasket could compromise the NEMA 4X seal N DANGER To reduce the risks associated with fire and explosion which if not avoided will cause death or serious injury and or property damage Do not install or use this product in a hazardous location 3M Touch Systems Proprietary Information 5 Chassis Touch 450 Monitor User s Installation Guide Steps for mounting and connecting WARNING To reduce the risks associated with electrical shock fire or explosion which if not avoided could result in death or serious injury and or property damage Follow all product installation instructions Performance of all procedures described in this document should be by trained personnel Engineer the installation of the monitor to take into account the operating environment e g shock vibration and or thermal factors A WARNING To reduce the risks associated with electri
29. not modify the monitor Do not substitute components Use only 3M components or 3M approved components for repairs WARNING To reduce the risks associated with electrical shock which if not avoided could result in death or serious injury and or property damage Before removing the monitor from its mounting or performing any other service to the monitor disconnect power to the unit Monitor installation No image Is the monitor receiving power Make sure that displayed blank Host computer s power cable is connected properly and securely screen to its power source Monitor s power cable is connected properly and securely to the power source AC DC power supply is connected to the monitor properly and securely and the LED on the AC DC power supply is lit green LED on the rear of the display is lit green If it is not try pressing the Power button on the rear of the monitor Try using another power cable 3M Touch Systems Proprietary Information 20 Maintenance and troubleshooting Is the monitor receiving a valid video signal from the host computer Make sure that Host computer is powered on Video cable is connected properly and securely to monitor and computer LED on the rear of the display is lit green If it is not try pressing the Power button on the rear of the monitor Nopins are bent in the video cable connector Video card is seate
30. ns on page 17 for manually adjusting horizontal and vertical display settings 3M Touch Systems Proprietary Information 13 CHAPTER 3 Adjusting the video display Your ChassisTouch 450 monitor has several control buttons and an on screen menu for adjusting the video display For example you can adjust m Pixel clock and phase to eliminate noise m Image contrast and brightness to your lighting conditions m Horizontal and vertical position of the image This chapter explains presents guidelines for adjusting the video display and describes how to use the available monitor controls to adjust the image to your liking Before you make any adjustments m Set the controls in normal lighting conditions m Display a test image or pattern while making video adjustments m Itis recommended that you first set display settings with the video driver on your host computer After establishing video driver settings run AUTO using the monitor s OSD controls AUTO and other OSD functions are explained in OSD controls in Table B Controls for adjusting the video display Your ChassisTouch 450 monitor has five controls for adjusting the video display Table B On the back panel there is also an LED indicator and a Power button Pressing the Power button turns the monitor s backlights on or off but does not affect power to the monitor 3M Touch Systems Proprietary Information 15 Chassis Touch 450 Monitor User s Installatio
31. ormation 16 Adjusting the video display PC Brightness Selecting the Brightness option as in Figure 3 allows you to adjust the brightness of the display Adjust the brightness using the UP and DOWN buttons Press EXIT to confirm a setting Contrast Selecting Contrast allows you to adjust the overall contrast of the display To change the setting use the UP and DOWN buttons Press EXIT to confirm a setting Phase If the phase of your monitor is not fine tuned you may observe unstable horizontal noise lines and cross talking stretching from the edge of small windows on your display To reduce this horizontal noise follow these steps 1 From the Windows desktop of the host computer select Start and then select Shut Down The Windows Shut Down dialog box appears on the monitor s display Visual noise is more visible and easier to eliminate if the display is in Windows Shut Down mode 2 Press the Menu control button to call up the OSD main menu select the PC icon and then select the Phase sub menu 3 Press the UP or DOWN control buttons to reduce the noise To confirm a new phase setting press the EXIT control button 4 After adjusting the phase setting select Cancel in the Windows Shut Down dialog box to return to your original Windows display Frequency If the Frequency setting is not fine tuned you may observe periodic vertical bars of video noise To reduce this vertical noise follow these steps 1
32. ous injury and or property damage Follow all product instructions Performance of all procedures described in this document should be by trained personnel Any servicing or other procedures not described in this manual are to be performed only by qualified personnel Read and understand all safety information before installing and using the monitor a Engineer the installation of the monitor to take into account the operating environment e g shock vibration and or thermal factors Properly install the monitor with a NEMA 4X gasket that is clean undamaged and effective Do not modify the monitor a Use only 3M components or 3M approved components for repairs f a replacement part is needed contact 3M Touch Systems Provide a clean reliable ground Use locking devices on connectors To ensure compliance with electrical codes and safe operation of the monitor have a licensed journeyman electrician familiar with local codes perform all wiring and installation tasks WARNING To reduce the risks associated with electrical shock or fire which if not avoided could result in death or serious injury and or property damage a If the monitor is mounted using a NEMA 4X panel gasket install the unit in a Listed UL enclosure If the monitor will be used in corrosive environments it is the responsibility of the user to test and evaluate the unit in those environments The monitor as ship
33. ped has not been evaluated for use in excessively corrosive environments 3M Touch Systems Proprietary Information i ChassisTouch 450 Monitor User s Installation Guide A WARNING To reduce the risks associated with electrical shock which if not avoided could result in death or serious injury and or property damage a Make sure that the ground potential difference between the monitor and the host computer is less than 2V Before removing the monitor from its mounting or performing any other service to the monitor disconnect power to the unit Provide adequate strain relief for all communications and power cables Do not use a damaged power supply Do not use a power cable that is damaged or frayed or a power plug that is damaged Do not allow liquid inside the monitor s metal enclosure A WARNING To reduce the risks associated with electrical shock or mechanical function which if not avoided could result in death or serious injury and or property damage If your monitor will be used in an environment where safety is an issue set the time for the Windows energy saver to be greater than the time for the Windows screen saver Do not use a non Windows screen saver in an environment where safety is an issue a If your monitor has a display power management system DPMS that is configurable from the display s on screen Utility menu do not turn off the DPMS A WARNING To r
34. ppropriate for the problems you are experiencing with the monitor You may also want to consult your video card user s manual for additional troubleshooting advice Maintaining your touch monitor To maintain your display and keep your monitor operating at peak performance m Keep your monitor and screen clean m Adjust the monitor video controls Refer to Chapter 3 for more information m Do not install the display in a place where ventilation may be hindered Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation Care and cleaning Touch screen The touch screen requires very little maintenance 3M Touch Systems recommends that you periodically clean the glass touch screen surface 3M Screen Cleaner 675 has been tested and approved for this use When cleaning your touch screen N WARNING To reduce the risks associated with skin contact or swallowing of cleaning solutions or fluids which if not avoided may result in minor or moderate injury and or cause property damage a Refer to the cleaner manufacturer s material safety data sheet MSDS and follow all instructions and recommendations on product label m Do not use any chemical that corrodes glass or any vinegar based solutions m Apply the cleaner with a soft lint free cloth Avoid using gritty cloths m Always dampen the cloth and then clean the screen Be sure to spray the cleaning l
35. r of colors 3M Touch Systems recommends that color depth be set at no less than 16 bit high color The video card must support one of the display modes specified in Table A If you select an unsupported video mode the monitor will stop working or display an unsatisfactory picture quality Table A Supported display modes and refresh rates Display Mode Refresh Rate Hz VGA 640 x 480 60 75 85 15 failsafe mode SVGA 800 x 600 56 60 75 85 15 failsafe mode XGA 1024 x 768 60 75 85 15 failsafe mode 10 Many video cards initially display a screen image at the VGA or SVGA resolution The ChassisTouch 450 monitor supports these resolutions Table A and so can display the desktop controls that let you change to the optimal resolution of 1024 x 768 For information on how to change resolution see Controls for adjusting the video display on page 16 Connect communications and power cables to the ChassisTouch 450 monitor by following these steps A WARNING To reduce the risks associated with electrical shock fire or explosion which if not avoided could result in death or serious injury and or property damage Use locking devices on connectors i f To ensure compliance with electrical codes and safe operation of the monitor have a licensed journeyman electrician familiar with local codes perform all wiring and installation tasks a Make sure that
36. rn Standard Time 9 a m to 5 p m throughout Europe Limited call back service is available on Saturdays and Sundays You can contact 3M Touch Systems Technical Support US only Eastern Standard Time by calling the hot line or sending a fax m Technical Support Hot Line 978 659 9200 m Technical Support Fax 978 659 9400 m Toll Free 1 866 407 6666 m Email US TS techsupport mmm com 3M Touch Systems Proprietary Information 3 Chassis Touch 450 Monitor User s Installation Guide 3M Touch Systems Worldwide Offices All offices can be reached through the web site www 3Mtouch com Country Telephone United Kingdom 44 0 1235 444400 United States 978 659 9000 Australia 61 395 82 4799 Canada 604 521 3962 France 33 1 45 13 90 30 Germany 49 0 2131 14 0 Hong Kong China 852 2333 6138 Italy 39 0 39 230 2230 Japan 81 4 4811 1133 Korea 822 552 3198 Singapore 65 96279173 Spain 34 934 15 6285 Taiwan 886 2 2704 9011 3M Touch Systems Proprietary Information 4 CHAPTER 2 Setting up the monitor About this chapter This chapter describes how to Mount the ChassisTouch 450 monitor in a panel to achieve a NEMA 4X IP66 seal around the front of the unit Connect communications cables Connect power Install Near Field Imaging NFD touch screen driver software Make recommended energy saver settings if the ChassisTouch 450 mo
37. tems ship on floppy disk with the ChassisTouch 250 monitor NFI drivers for the following operating systems may be downloaded at www 3Mtouch com m Windows NT m Windows 98 m Windows 95 Communications The communications ports available on the ChassisTouch 450 monitor are m RS 232C compatible asynchronous serial port m 15 pin female video connector Power With the AC DC power supply the output power is 12 VDC Operating conditions Condition Range Operating temperature 0 to 50 C 32 F to 122 F Humidity 50 C 5 to 95 non condensing Maximum operating altitude 6 560 feet 2 000 meters Vibration 5 to 57 Hz 0 006 in peak displacement 58 to 2000 Hz 1 0 G acceleration Shock Acceleration 15 G Pulse duration 11 ms 3M Touch Systems Proprietary Information 25 Chassis Touch 450 Monitor User s Installation Guide Non operating conditions Condition Range Storage temperature 25 C to 60 C 13 F to 140 F Maximum storage altitude 40 000 feet 12 192 meters Vibration 5 to 57 Hz 0 015 in peak displacement 58 to 2000 Hz 2 5 G acceleration Shock Acceleration 30G Pulse duration 11 ms Safety standards UL 60950 3rd edition for Information Technology Equipment EN 60950 CSA C22 2 for Information Technology Equipment via UL s No 60950 00 C UL certification Dust and moisture resistance NEMA 250 Electrical Enclosures Type 12 Type 4 Type 4
38. ty damage Properly install the monitor with a NEMA 4X gasket that is clean undamaged and effective Use only 3M components or 3M approved components for repairs 7 Attach the monitor to the panel from the back using the locknuts and washers supplied 8 Gradually tighten diagonal pairs of locknuts until the height of the panel gasket is compressed to between 0 125 inches 3 175 mm and 0 1 inches 2 54 mm Important Do not overtighten the panel mounting locknuts If the gasket is compressed to a height that is less than 0 1 inches 2 54 mm the NEMA 4X IP66 seal may be compromised and the 3M Touch Systems warranty will be invalidated ChassisTouch 450 Monitor Panel Locknut ChassisTouch 450 Monitor Gasket Figure 1 Panel mounting the monitor 9 Before making cable connections make sure that an appropriate video card and video driver is installed on the host computer For information on installing the video card and video driver refer to your video card manufacturer s documentation The ideal video settings for the ChassisTouch 450 monitor are Display mode also called desktop area or video resolution 1024 x 768 3M Touch Systems Proprietary Information 7 Chassis Touch 450 Monitor User s Installation Guide m Refresh rate also called vertical scan rate or vertical sync 60 Hz Color depth also called color palette or numbe
39. ws 95 drivers they are available for download from www 3Mtouch com Floppy disk with the linearization file for your NFI touch screen If it is ever necessary to uninstall and reinstall the touch screen driver software you may need the NFI linearization file from the floppy disk Important The linearization file for your monitor can also be retrieved from www 3Mtouch com You will be prompted to enter your NFI touch screen serial number located on the back of the ChassisTouch 450 monitor Related documents For information on how to install and customize driver software for the ChassisTouch 450 monitor refer to the software guide listed below that is appropriate for your operating system The software guides may be downloaded from the 3M Touch Systems web site www 3Mtouch com For Windows XP Professional and Windows 2000 Professional operating systems refer to MicroTouch NFI Software Guide For Windows XP and Windows 2000 3M Touch Systems Proprietary Information 2 Overview Note To install drivers for Windows XP and Windows 2000 on the ChassisTouch 450 monitor follow installation instructions on page 10 of the ChassisTouch 450 User s Installation Guide m For Windows NT 4 0 Windows 98 and Windows 95 operating systems refer to NFI Touch Screen Software Users Guide For Windows NT Windows 9X Windows 3 1 and MS DOS Note The sections of this software guide that pertain to Windows 3 1 an
Download Pdf Manuals
Related Search