FRONT PANEL: BACK PANEL:
Contents
1. 0 OO D8 a adia amp FRONT PANEL 1 Mic INPUT This is a balanced XLR input for connecting a dynamic microphone This can be a vocal mic to sing into while you play or alternatively an instrument mic to amplify an all acoustic instrument that does not feature an onboard preamp system You may also use this input to connet an electro acoustic instrument with a balanced output signal 2 Mic LEVEL This control determines the output volume of the sound picked up by a microphone if one is used 3 Instrument INPUT This is a 1 4 6 3 mm input jack socket for plugging in an electro acoustic instrument We recommend that you always use a high quality shielded guitar cable to prevent any background noise interference or unwanted feedback 4 Instrument LEVEL This control determines the output volume of any instrument plugged into the amplifier via the guitar input jack 5 PASSIVE ACTIVE SWITCH This switch enables the user to choose between passive and active modes according to whether the instrument connected is passive without preamp or active with preamp 6 TREBLE This control determines the level of high frequencies in the output signal Adding TREBLE will make your guitar sound brighter and sharper 7 MID This control determines the level of middle frequencies in the output signal Adding MID will make your guitar sound rounder and fuller 8 PARAMETRIC MID This control allows you to fine tune your guit2. HAZARD DO NOT EXPOSE THIS APPLIANCE TO MOISTURE OR RAIN DO NOT OPEN CASE NO USER SERVICEABLE PARTS QUALIFIED SERVICE PERSONNEL REAR PANEL MAY BECOME TOO HOT TO TOUCH LEAVE ENOUGH SPACE FOR PROPER VENTILATION POWER CONSUMPTION 185W BACK PANEL WARNING This amplifier must be earthed Please check that the supply voltage details given on the rating label located on the rear panel are in accordance with your electricity supply 1 POWER SWITCH This switch turns the amplifier on or off 2 MAINS INPUT This is the input socket into which the mains power cable must be connected This amplifier is supplied with a power cable with a moulded on plug If the socket outlets in the home are not suitable for this plug use an appropriate plug adapter that can handle the power required for the amplifier 3 POWER FUSE In the event of the power fuse having to be replaced first unplug the power cable from the mains outlet Then remove the fuse cover and replace the power fuse with another fuse of the same type and value Never plug the power cable back into the mains outlet without the fuse cover If the power fuse blows up again when powering on the amplifier take the apparatus to a suitable service centre for repair 4 EXTERNAL SPEAKER OUTPUT This is a 1 4 output jack with which you can connect an external speaker cabinet if desired This output is adapted for an 8 Ohm impedance load The external speake
3. ON position the power LED will glow and your amplifier is ready for use IMPORTANT SAFETY INSTRUCTIONS READ AND KEEP THESE INSTRUCTIONS HEED ALL WARNING e If after you have followed the instructions outlined above your amplifier fails to function please contact your dealer Under no circumstances should the amplifier be opened Leave all servicing to qualified personnel e Electrical appliances must never be used in conditions of high humidity or heat To prevent any risk of fire or electric shock never spill or splash liquids on the amplifier Should this happen unplug the power cable from the mains outlet immediately e We would like to draw your intention to the instructions printed on the notice attached to the back of the amplifier CAUTION TO PREVENT THE RISK OF FIRE AND SHOCK CAUTION HAZARD DO NOT EXPOSE THIS APPLIANCE TO MOISTURE OR RAIN DO NOT OPEN REAR PANEL MAY CASE NO USER BECOME TOO HOT SERVICEABLE PARTS TO TOUCH INSIDE REFER SERVICING TO QUALIFIED SERVICE HOT LEAVE ENOUGH SPACE FOR PROPER PERSONNEL VENTILATION e Exposure to extremely high noise levels may cause permanent hearing damage especially when using headphones Please use this amplifier responsibly for you and your neighbourhood MARKING amp CONFORMITY 1 The CE mark on this product means it conforms to the EMC Directive 89 69 EEC CE marking Directive 93 68 EEC and Low Voltage Directive 72 23 EEC 2 The Cros
4. ar sound by cutting or boosting the mid frequency parameters of the output signal At a low level the PARAMETRIC MID control will emphasize the lower mids while increasing the level will bring out the upper mids The PARAMETRIC MID control can help you explore a wide variety of different guitar tones 9 BASS This control determines the level of low frequencies in the output signal Adding BASS will make your guitar sound warmer and heavier 10 SPRING REVERB This is the reverb intensity control This controls the amount of reverb that is added back to the original dry signal Adding REVERB will produce a reverberation effect in your instrument sound as though you were playing in a large hall A little can go a long way in adding that special depth to your sound If engaged the reverb is always active in both microphone and guitar channels 11 CD MP3 INPUT This is a line level 1 4 6 3 mm stereo jack into which an MP3 CD Tape player may be connected 12 PHONES This is a 1 4 6 3 mm stereo jack output to connect the headphones When headphones are connected no sound is produced from the speaker 13 DI OUTPUT This is a line level balanced XLR output that enables you to connect the amplifier directly to a recording or mixing console USER S MANUAL a 60 AAR ACOUSTIC AMPLIFIER z AA pl EXTERNAL SPEAKER z MIN 40W 8 OHMS FUSE T800mAH 250V CAUTION TO PREVENT THE RISK OF FIRE AND SHOCK
5. r must therefore have a minimum impedance of 8 Ohms and a minimum power handling of 40 watts Under no circumstances should you connect a 4 Ohm speaker cabinet as this can severely damage your amplifier A 16 Ohm cabinet will present no danger though the full power of the amplifier will be slightly compromised Always use a properly designated speaker cable and NOT a guitar cable when connecting external speakers TECHNICAL SPECIFICATIONS 60 Watts RMS 4 Ohms load 10 8 Ohms internal Speaker Ma RATEN Power EOuespesnes w Coaxial Tweeter 8 Ohms external Speaker Frequency Response 20 Hz to 20 kHz Signal to Noise Ratio 64 dB max Rated Power Input Impedance 100k Ohms Power Consumption 185 Watts max Maximum Input Level 80 mV RMS asmamen iw O Dimensions H x W x D 45 x 49 x 27 cm 17 7 x 19 3 x 10 6 in Features and Specifications are subject to change without notice 60 AA R 3 USER S MANUAL INSTRUCTIONS FOR USE Plug the mains lead into a suitable power socket and connect your instrument to the input socket of the amplifier with a suitable guitar lead this lead is not supplied with the amplifier but is normally supplied with the guitar You may also plug a microphone into the XLR input provided If connecting a microphone please ensure that the volume level is set low before turning on the amplifier as feedback can otherwise result possibly causing damage to the speaker Finally press the Power Switch to the
6. sed out Wheeled Bin is to draw your attention to the WEEE Waste Electric amp Electronic Equipment Directive 2002 96 EC It means this apparatus must be collected separately for recycling 3 RoHS compliant means this device conforms to the Directive 2002 95EC on the restriction of the use of certain hazardous substances in electrical and electronic equipments such as Mercury Lead Cadmium Hexavalent Chromium Polybrominated Buphenyl PBB and Polybrominated Diphenyl Esthers PBDE DISTRIBUTOR DEALER C X RoHS compliant USER S MANUAL A 60 AAR EMD Music 01 2008 UK E aG Universe al Hure USER S MANUAL EF pT o Pat on as j om ft ACOUSTIC GUITAR AMPLIFIER W SPRING REVERB GO AA R
Download Pdf Manuals
Related Search