USER MANUAL Model: LMDT-810 Self programming motion
Contents
1. ex factory Brightness lux setting H M L Frequency 433 92 MHz Waterproof IP44 Transmitting distance with receiver 20M closed area Battery 3V DC Alkaline battery AAA 1 5V x 2 Excluded in LMDT 810 ex factory Angle of detection vertical max 202 degrees horizontal max 110 degrees without lens cover 20 degree with lens cover uncut ex factory TROUBLE SHOOTING a No activation check battery life or polarity or unsuccessful connection b Receiver stays ON continuously LMDT 810 may be suffering from false activation Adjust the position angle of the detector to solve the problem Note After installation please check LMDT 810 is working properly in all switch settings with compatible self programming receiver WARNING LMDT 810 working compatible receiver DOES NOT operate in common with other transmitter Otherwise if the receiver lamp 1s switched ON already by another transmitter for example handy transmitter LYCT 505 then when LMDT 810 detects movement and sends ON signal to the same receiver this receiver lamp starts to dim Do not use LMDT 810 with dimmer 2 x Fresh AAA 1 5V battery installed in LMDT 810 are important for providing stable current voltage to LMDT 810 thus enhancing detection and transmission capability Also 2 fresh batteries can help to keep each other s battery life as long as it should be www nexa se support nexa se2. range in order to switch on the light and upon delay off time switch off the light automatically Manual switch After the code is learnt the Set Del switch can also be set as a manual switch to manually switch the light on off Adjust to Set to switch the light on adjust to Del to switch the light off Manually adjust to Del when LMDT 810 detects movement can still switch on connected light and automatically switches off the light at delay time end However if manually adjusted to Set to switch light on the light will not switch off automatically at delay time end Another connected transmitter must be used to switch the light off D Code deletion Purpose of code deletion the user does not want LMDT 810 to work with a certain receiver In this case the user should delete LMDT 810 code from the limited memories of the self programming receiver to release the memory to the next transmitter code setting Place LMDT 810 in SET mode near to self programming receiver which it works with Press learning button of the receiver LED flashes continuously Slide LMDT 810 learn switch from SET to DEL LMDT 810 sends code to receiver Receiver connected lamp flashes twice to confirm the code deletion Receiver LED stops flashing oe oe a LMDT 810 and receiver are no longer connected TECHNICAL SPECIFICATION Delay off Time 5sec 1min Smin 10min Learn Switch in DEL mode when LMDT 810
3. ELECTRONICS USER MANUAL Model LMDT 810 Self programming motion detector transmitter for outdoor use IP44 FEATURES 67 million code combinations no interference from neighbours Easy operation no wiring battery operated Outdoor use compatible with ARC self programming type receivers connected to lamp or doorbell as home safety system Not suitable for dimmer receiver Delay off time switch design After delay LMDT 810 sends a signal to switch off the receiver Battery low indication INSTALLATION A INSTALLATION STEPS I 3 0m 1 Select required location position 3 4 metres above ground away from trees direct sources of heat and direct sunlight Remove LMDT 810 from base Using base as a template mark and drill 4 suitable holes Secure base to wall using screws Re attach LMDT 810 Adjust angle and direction oo a aaa Battery replacement illustrations B DETECTION ANGLE AND RANGE a LMDT 810 detection angle is 110 degrees To reduce the angle of detection keep the attached lens cover on LMDT 810 If necessary cut off lens cover determine the detection angle size from min 20 degrees to max 110 degrees qi Z Y kea SW b Detection range adjust LMDT 810 bracket to select required range 10 metres max FUNCTION OF SWITCHES A Delay off Time Switch 4 options 5sec Imin Smin 1 0min Each option indicates when the time period ends LMDT 810 send
4. ove D Battery Low Indicator Battery low indicator is positioned inside the sensor lens If the battery is low the indicator flashes after LMDT 810 delay time ends Within delay time period LMDT 810 still works normally until delay time ends When the battery is low the battery indicator starts to flash to inform the user to replace the battery When the battery is low battery low indicator starts to flash LMDT 810 does not work until the user replaces the batteries and re starts OPERATION A Code learning as 1 Place LMDT 810 in DEL mode near to self programming s receiver which it will work with 2 Press learning button of the receiver LED flashes continuously Slide LMDT 810 learn switch from DEL to SET LMDT 810 sends code to receiver 4 Receiver connected lamp flashes twice to confirm the learned code Receiver LED stops flashing DELSET CC LEARN B Set up Delay off Time Switch 5sec Imin Smin 10min as option See FUNCTION OF SWITCHES C Set up Lux Setting Switch H M L as option See FUNCTION OF SWITCHES Note whether there 1s surrounding light that can influence the brightness and affect the Lux setting choice For example in the late evening the lux setting is L However if there is a lamp in environments where LMDT 810 would be able to detect the user may change lux setting to M After each set up process LMDT 810 detects movements within the detection
5. s an OFF signal to the receiver to switch off the receiver and its connected lamp or light Doorbells are not restricted by delay off time As long as LMDT 810 detects an object again it sends an ON signal to the receiver to switch on the receiver and its connected lamp light or doorbell again The delay off time counts down when the object stops moving B Learn Switch DEL SET 2 options DEL means delete learning code from compatible receiver SET means set up learning code with compatible receiver C Lux Setting Switch 3 options H M L H 24 hours in standby As long as the object is within E Horane detection distance it will be detected At H setting delay off time switch is disabled When LMDT 810 works with doorbell receiver set H mode M detects when brightness is below 20 5 lux late afternoon L detects when brightness is below 10 5 lux late evening After switching from M to L for example there should be a pause of at least 30 seconds leaving LMDT 810 detecting unchanged light and no movement the L lux setting can be accurately set up activate from the product IC When it is darker than the L lux level LMDT 810 can detect objects A similar situation applies for switching from H to M or H to L or vice versa switching from darker level to brighter level There is a need to remain unchanged for 30 seconds as described ab
Download Pdf Manuals
Related Search