Microsoft Word Viewer - FM4200 Sample User Guide v0.4
Contents
1. Pic 3 Standard FM4200 2x10 socket pinout The external 10 30 V DC 12 W Max power supply must be used to power up the device Connect power supply to 1 pin and 11 pin as shown above 2 3 Placement of GPS antenna e GPS antenna must be placed so its state is as horizontal as possible if antenna is leaning more than 30 degrees it is considered incorrect mounting e GPS antenna cable cannot be bent more than 80 degrees e GPS antenna must be placed sticker facing down Pic 4 GPS antenna correct mounting It is recommended to place GPS antenna as close to the window as possible NOTE that most of modern office windows are equipped with filters that could block GPS signal so for best GPS signal quality we recommend to put GPS antenna outside on windowsill some plate etc 2 4 Connect FM4200 to the computer FM4200 Configuration is performed via FM4200 Configurator program Latest FM4200 Configurator versions can be downloaded from http avl1 teltonika It downloads FM42 FM4200 configurator operates on Microsoft Windows OS and uses MS Net Framework 2 0 or higher Please ensure that MS Net Framework 2 0 or higher is installed on your PC before starting configurator Latest MS Net Framework version can be downloaded from official Microsoft web page Module configuration is performed over cable labeled PORT1 2 Configuration process starts from loading FM4200 Configurator program and selecting COM port Select COM port a2. FM4200 Sample User Guide 1 About the document This document contains information about testing the FM4200 samples and configurations commonly used in such cases 1 1 Login to TAVL application TAVL application is used for users to be able to see the AVL data such as GPS location speed ignition and other I O elements values from FM4200 devices in the users friendly way Information required to download and use the TAVL application is provided in the next paragraph After downloading the TAVL application simply open the taviexe file and use your login information provided below Teltonika TA L NET Login Please enter login name and password Tene Client username menue Client password Client Server avl teltonik a lt ki Ei ET a E iglish Connection Settings Pic 1 Login to TAVL application 12 Downloading the TAVL application 1 2 1 PC requirements TAVL application runs on a PC with MS Windows XP or MS Windows Vista with latest service packs MS NET Framework v3 5 SP1 and Crystal Reports are also necessary components TAVL application supports MS MapPoint copyright 2008 Microsoft or any MapX copyright 2008 MapInfo Corporation maps additional maps have to be installed on users PC 1 2 2 NET Framework installation Download NET Framework 3 5 SP1 from Microsoft website and install it url http www microsoft com downloads thankyou aspx familyId ab99342f 5d1a 413d 8319 8
3. moving Only send parameter is 60 seconds and there are more I O elements like in Logbook scenario Following I O elements vales are monitored in every AVL data record DIN1 as ignition values 0 Profile 3 1 Profile 1 DIN2 as panic button values 0 1 AIN1 Analog Input values 0 30 000 mV Movement values 0 object is not moving 1 object is moving Speed values current vehicle speed in km h Odometer values what is driven distance between two coordinate s points e Current profile show in which profile FM4200 works e Power voltage values from 10 V to 30 V according to the power source Additional AVL data records called events are generated on following parameter value changes e If power voltage value falls less than 11 V e Speed is less than 5 km h for more than 1 minute e Panic button is pressed DIN2 1 3 4 2 What is the purpose of testing FM4200 in this scenario This scenario helps to learn about the profile of the exchange of properties since it is one of the most important FM4200 functionality Change the profile allows the collection of detailed data when the object moves and the use of deep sleep functionality to save battery power when the object is not moving In this scenario add two new very important and frequently used settings iButton which helps to authorize a driver and fuel tank level which allows you to see real time what is the tank of fuel
4. this document Again the only additional configuration must be made is the APN configuration The description of the APN configuration is described in paragraph 2 5 1 The Logbook scenario configuration is based on rare periodic AVL data acquisition Min period 1 hour According to this configuration the FM4200 device will generate AVL record every one hour and if any of the below described I O elements values are increased or decreased over the configured thresholds Periodic AVL data is sent via GPRS to the server once a day Min saved records 24 Send period 300 s if no I O event happen If any of the events described below happen the AVL data record with all AVL information is sent to the server as soon as the event appears Following I O elements vales are monitored in every AVL data record e DIN1 as ignition values 0 Off 1 On e DIN2 as panic button values 0 1 e Movement values 0 object is not moving 1 object is moving e Power voltage values from 10 V to 30 V according to the power source Additional AVL data records called events are generated on following parameter value changes e If power voltage value falls less than 11 V e Speed is less than 5 km h for more than 1 minute e Ignition is turned ON OFF DIN1 1 or DIN1 0 e Panic button is pressed DIN2 1 3 3 2 What is the purpose of testing FM4200 in this scenario After the testing is successfully done the
5. 0 device is not moving the AVL data records are generated periodically every 600 seconds Min period 600 s AVL data is sent via GPRS to the server as soon as the AVL data record is generated Min saved records 1 Send period 1s According to this configuration one AVL data record containing information about the GPS position and Input Output I O parameters is sent to the server at least every 600 seconds Following I O elements vales are monitored in every AVL data record e DIN as ignition values 0 Off 1 On e Movement values 0 object is not moving 1 object is moving e Power voltage values from 10 V to 30 V according to the power source Speed values current vehicle speed in km h e Odometer values what is driven distance between two coordinate s points Additional AVI data records called events are generated on following parameter value changes e If power voltage value falls less than 11 V e Speed is less than 5 km h for more than 1 minute e Ignition is turned ON OFF DIN1 1 or DIN1 0 3 2 2 What is the purpose of testing FM4200 in this scenario The main propose of this testing scenario is for the user to see the highly detailed track as in the sample screenshot below of his driven track in the city The user will be able to see his vehicles current position as well as the position in any selected time in the past The user will be able to see the time and points in the ma
6. 1da479ab0d7 amp displayLang en mirror http avl1 teltonika Jt downloads tavl Framework dotnetfx35setupSP1 zip If the download doesn t start automatically click on the Start Download button 1 2 3 Crystal Reports installation Download and install Crystal Reports for NET Framework url http avl1 teltonika It downloads tavl Crystal o20Reports CRRedist2005_ x86 zip 1 2 4 TAVL application installation Downloads and extract latest available version of TAVL application url http avl1 teltonika It Downloads tavl Note that if any additional information about the usage of the TAVL application is needed please see the latest TAVL3 Application User Manual 2 Getting started with FM4200 device This paragraph contains the information needed to successfully launch and use the FM4200 device The steps below should be followed carefully to completely test the FM4200 2 1 SIM card insert scheme Pic 2 Illustration of how to insert the SIM card NOTE must be disabled the PIN code request in SIM card 2 2 Power source connection x EXT BAT 10 fo fo 20 EXT BAT OUT 2 9 fo fla 19 OUT 1 OUT 3 8 fo fla 18 OUT4 AIN 2 7 a flo 17 AIN1 AIN 4 6 aS 16 AIN3 DIN 2 5 fo fa 15 DIN1 DIN 4 4 fo flo 14 DIN3 1W PWR 3 Lo flo 13 1W data CAN L 2 fo fo 12 CANH GND 1 ENEI 11 YCC 10 30 V DC
7. and prevent illegal activities
8. criptions of the sample scenarios and the configuration for each case 3 1 First test Usually the client s office is the first environment in which the FM4200 device is tested at the beginning To make this test faster you should upload 1IstScenarioConfig_FirstTest xml file to the device with the prepared configuration 3 1 1 Configuration The sample FM4200 devices are shipped already uploaded with First test scenario configuration The only additional configuration must be made is the APN configuration The description of the APN configuration is described in paragraph 2 5 1 And don t forget that this scenario must be saved to 3 profile because FM4200 works in 3 profile by default how to do that is shown in Picture 6 The First test scenario configuration is based on fast periodic AVL data acquisition Min period 30 s and AVL data sending via GPRS to the server as soon as the AVL data record is generated Min saved records 1 Send period 1 s According to this configuration one AVL data record containing information about the GPS position and Input Output I O parameters is sent to the server every 30 seconds Following I O elements vales are monitored in every AVL data record e DINI as ignition values 0 Off 1 On e Movement values 0 object is not moving 1 object is moving e Power voltage values from 10 V to 30 V according to the power source 3 1 2 What is the purpose o
9. eset device Get actual Profile Global parameters Temperature sensors Flashna 0 Wersion 4 Source Device COM port COM PE Flash no 1 Fi ga iuztem Flash ng 2 Fz S Flash no 3 Fs sleep Mode Normal l Flash na 4 F4 Send parameters Accelerometer 0 Pic 6 Configuration toolbar view Configuration files for all Sample Scenarios described in 3 paragraph are allready prepared by Teltonika Open the FM4200 Configurator software select correct COM port and click on Load from File button 1 from the main toolbar Browse for the required configuration file and click OK Enter the APN parameters into the GPRS section of the configuration according to the instructions described in 2 5 1 paragraph Click on Save to Flash and Flash no 3 buttons 2 3 to upload the configuration into the FM4200 device FM4200 has 4 user editable profiles stored in Flash no 1 4 memories and one extra profile stored in Flash no 0 which can not be edited by user Profile from Flash no 0 is used by system and can not be selected as active while profiles from Flash no 1 4 are fully editable and can be selected as active Please note that by default FM4200 works in 3 profile so you must save configuration into 3 profile To check the current FM4200 configuration click on Read from Flash 3 4 5 buttons To save the modified configuration click on Save to File button 6 and the configurati
10. f testing FM4200 in this scenario After the testing is successfully done the user is introduced to the basic FM4200 work periodic AVL data acquisition and sending to the server with monitoring of the basic I O parameters The user is able to see his position according to GPS in the TAVL application software 3 2 City Scenatio This scenario is useful when need detailed track and get only very important information from I O elements about which is written below 3 2 1 Configuration To completely test the City Scenario please load the prepared configuration file 2ndScenarioConfig_City xml which has been received together with this document Follow the instructions in paragraph 2 55 to upload the FM4200 with the required configuration Again the only additional configuration must be made is the APN configuration The description of the APN configuration is described in paragraph 2 5 1 The City scenario configuration is based on fast periodic AVL data acquisition mainly according to the change of the objects geographic angle Min Angle 20 degrees According to this configuration the FM4200 device will generate AVL record every time the object s angle is changed more than 20 degrees Such AVL data acquisition is rational in cases the object mostly moves in the city Min Distance 200 meters so the additional AVL record will be generated after driving more than 200 meters in the straight line If the object with FM420
11. n 2 Browse for the required configuration file and click OK After that save global configuration to the flash click on Write to FLASH 3 ___ Set IMEL Reset device Get actual Profile Global parameters J Temper evice COM porth COMI Global parameters Profile Settings F Enable Profile change on event Voice S elt 4 Micsophone level 13 of 0 14 Speaker level 37 af 0 100 Call Siethrags Call umbe al on a Call bigger i evic Feco Setbngs J Start from Newest s Record seanch SIM Settings Accelerometer Settings 46 Accelerometer sanzivty Analog Input Settings ANTANZANJANA 0 04 Anaiog mput vollage range Record Retreth Setting 259200 Record Refresh timeout 2 rre Carnie j t Close Pic 10 Global configuration Additional configuration must be made is the APN configuration but need enter it to profiles 1 profile and 3 profile The description of the APN configuration is described in paragraph 2 5 1 The Profile change on event scenario configuration is based on detailed information send to the server in profile 1 and save battery charge when vehicel not move in deep sleep 3 profile According to this configuration the FM4200 device will generate AVL record with detailed information when ignition is ON or device is moving This scenario 1 profile configuration is like City scenario when object is
12. nd click Connect button If connection is successful then instead of Connect appears Disconnect button ad FM42xx Configurator 1 0 1 24 File Device Help Read From Flash Sawe to Flash Load From File Sawe to File Load Default Profile et IMEI Reset device Get actual Profile Global parameters Temperature sensors PefieNe 0 Veson 0100 E ED j comi System System eai GPS z GSM GPRS SMS Send parameters Accelerometer lO Pic 5 Connect FM4200 2 5 Loading the Configuration into the FM4200 Device FM4200 Configurator must be used to configure the FM4200 device Using the configurator prepared Sample Configurations can be uploaded into the FM4200 or custom device configuration can be made aa FMA Dx Configurator TOT 24 File Device Help 2 Read from Flash Save to Flash Load from File Save to File Load Default Profile Get IMEI Reset device Get actual Profile Global parameters Temperature sensors Souce Device compon oo Flash na 1 Chrlt F1 Pratie Nee 3 Flash na 2 Chrl F2 GPS a nivale Flashna 4 Ctrl F4 E GPRS SMS Send parameters Accelerometer IO sy FM42xx Configurator 1 0 1 240000 nT leg File 4 Device Help 6 F Read from Flash Save to Flash Load from File Save to File Load Default Profile Get IMEI R
13. on will be saved into the file with xml extension The saved configuration will be able to upload into any FM4200 device in the same way as described above Click on the button Get actual profile 7 and you will see currently used profile number E Actual profile 3 Pic 7 Actual profile notification 2 5 1 APN configuration In order to FM4200 device to be able to connect to local GPRS network and send AVL data the following APN data provided by local GSM services provider must be entered into FM4200 configuration e Acces Point Name APN with authentication type CHAP or PAP if required e APN login e APN passwotd Sample below is of GPRS configuration of German EPLUS GSM service provider a FM42xx Configurator 1 0 1 24 File Device Help Bazd kon Flash Save to Flash Load From File Saveto File Load Debau eile ss Get IMEI 1 R Reset h dezicc d Get Lacie eils la Globa peace J Leppera sensors Pat e Ome deen cost Ses TE Point TE APN System aes Authentication type PAP e da eae r Emi kd GPRS epluz APN username SMS Send parameters APN password _ S assword Accelerometer f P rae Geofence Tag IF address Pic 8 GPRS configuration 3 Sample scenarios This section of the document describes the commonly used FM4200 testing scenarios and helps users to perform the detailed testing of the FM4200 device Below you will find the des
14. p in which the ignition has been turned ON OFF power voltage has become less then 11 V car battery needs to be recharged gt es oe i Ya an lt A ANa e oy ee he Gata _ a a Be mt oo ce j i p K F ae it Prat i F IE l aT Es F A i z F od 2 E N a ae eah Space We a il TE AIE AE ia A aia al Ta nay hss Pic 9 Track of the FM4200 working in City scenario The track showed in the screenshot above contains the information of 3 days driving of real vehicle in the city of Vilnius Lithuania Using the service of local GSM service provider Bite GSM 1 MB of data has been transmitted through the GPRS to generate such track NOTE that GPRS traffic differs from the GPRS coverage at the area and the GSM service provider s data averaging policy so the GPRS traffic can be higher than the described in the example above 3 3 Event based Logbook scenario Another useful FM4200 testing scenario is testing the device in the Logbook scenario Working in such scenario the position of the object with FM4200 device and I O elements values are sent to the server via GPRS on high priority events when I O elements values exceeds the configured thresholds 3 3 1 Configuration To test the event based Logbook scenario please load the prepared configuration file 3rdScenarioConfig_Logbook xml which was received together with
15. user is introduced to the FM2200 work based on events Such device s functionality is needed in cases when no detailed track is needed but the work of any vehicle is needed to be monitored The user will be able to see the information about the exact time of turning the ignition ON or OFF Panic Button activation vehicles battery voltage decrease Such event based Logbook is usually needed for the companies administrating big amount of the working vehicles Driver s and vehicle s working hours can be monitored using such case 3 4 Profile change on event One of the most widely used scenarios of the FM4200 testing scenario is testing the device in the Profile change on event Working in such scenario the position of the object is very detailed when it is moving or ignition is ON When device not move 10 minutes or DIN1 is OFF then it change profile from 1 to 3 and after 5 minutes if it not move goes to deep sleep mode 3 4 1 Configuration To test the event based Profile change on event scenario please load the prepared configuration file 4thScenarioConfig_Profilel xml into Flash no 1 as shown in Picture 6 After that please load the prepared configuration file 4thScenarioConfig_Profile3 xml into Flash no 3 and load AthScenarioConfig_GlobalParam xml file to Global parameters as shown below Firstly click on Global parameters 1 button from the main toolbar then on Load from file butto
Download Pdf Manuals
Related Search