Home

GOT-A900 Series Operating Manual (GT

1. 2 Remove the slot cover Save the removed slot cover carefully If the A9GT J71E71 T is used alone without the slot cover foreign matter will enter the unit causing a failure or malfunction Slot cover s SA Bus connection 3 Fit the bus connection board to the A9GT J71E71 T board 4 Tighten the mounting screws 2 pcs of the bus connection board to the specified torque 36 to 48N e cm to fix the bus connection board 5 After fitting the bus connection board mount the A9GT J71E71 T to the GOT 2 5 About the System Programs The system programs compatible with the GOT must have been installed to use the gateway functions Refer to the following manual for the system programs necessary for the gateway functions their installation methods and precautions lt gt GT Designer2 Version1 Operating Manual 2 6 Precautions for System Configuration Connection to the intranet must be fully safeguarded Consult the network access provider or network manager person who does network planning IP address management etc We have no liability for any system problems that occur at the time of connection to the intranet If a delay occurs due to network congestion take preventive measures e g install a bridge 3 OPERATION SEQUENCE A general procedure for using the gateway functions is given below l Examine the configuration of the whole system Examine the Connection structure of the whole system such as
2. 30 iil ll a eg aam 2 When using gateway devices directly Access to the other station GOT occurs 10 times 1 to 10 When one time of access requires 50ms the necessary processing time is about 500ms Script description example w D200 1 2 w EGO w D201 1 2 w EG1 w D202 1 2 w EG2 w D203 1 2 w EG3 w D204 1 2 w EG4 1 2 w EG5 128 1 2 w EG6 w D1 06 w D205 1 2 w EG7 w D206 1 2 w EG8 1 2 w EG9 5433 EGO to EG9 D106 i D200 to D206 Point P About the written values In the above 1 the gateway devices are batch accessed when the script execution condition is established Therefore the gateway device values available when the condition is established can be processed as the written values In the above 2 the gateway devices are accessed one by one after the script execution condition is established Therefore the written values may differ from the gateway device values available when the condition is established Gateway device setting When assigning the PLC devices to the gateway devices set the same type of devices of the same PLC together where possible By setting the same devices of the same PLC together as in the following 1 the number of access times can be reduced improving the processing speed 1 Devices of host other station and other PLC are set together When the GOT
3. CA gt ftp fto gt open 10 97 14 200 connected to 10 97 14 200 220 GOT900 FTP server ready user GOT900 331 Password required Password 230 User logged in fto gt Login image when the other personal computer has already connected to the GOT CA gt ftp ftp gt open 10 97 14 200 connected to 10 97 14 200 220 GOT900 FTP server ready user GOT900 530 Not logged in ftp gt Login image when the password is incorrect CA gt ftp fto gt open 10 97 14 200 connected to 10 97 14 200 220 GOT900 FTP server ready user GOT900 331 Password required Password 530 Not logged in fto gt Reading the file of the GOT PC card Read the file in the following procedure Notification of no file conversion s sssssssssssnsrnrnnrnsnsene eneen Read of file Read image fto gt binary 200 Command Okey ftp gt get SNAP0001 BMP 200 PORT command successful 150 Opening connection 226 Closing data connection 250 bytes received in 0 02 seconds ftp gt Writing a file to the GOT PC card Write a file in the following procedure Notification of no file conversion cccetecseeseetectteeseeteeneens 2 Selection of the write mode 32 Display of the file name to check for the same file name Deletion made if the same file exists ee 6 File write Write image fto gt binary 200 Command Okey ftp gt quote gtwr 200 command successful
4. b Numerical display function Description D100 to D101 Network c Lamp display function set two Description Device GB100 to GB101 Network 2 GOT 2 setting example a Client setting NET No PLC No IP Address 1 10 97 14 1 b Script function Description Trigger type Data format Screen script While ON bit device that indicates production completion Unsigned BIN 16 bit 1 1 w EG2 w HR200 Writes the production count to the PLC 1 set 1 1 b EG0 00 Turns ON the write completion signal Script 1 Script description 3 GOT 3 setting example a Client setting NET No PLC No IP Address 1 10 97 141 b Script function Item Description Screen script Trigger type While ON bit device that indicates production completion Data format Unsigned BIN 16 bit 1 1 w EG3 w W200 Writes the production count to the PLC 1 set 1 1 b EG0O 01 Turns ON the write completion signal Script 2 Script description 5 17 5 17 5 5 Precautions This section provides the precautions for using the server and client functions Precautions for assigning the devices in the gateway setting 1 The gateway devices are set as at least two points and set on a two point basis thereafter 2 When a bit device is assigned 32 points are set starting from the set device 3 When a device was not assigned the unassigned area empty area is on a wo
5. Definition and Cause Corrective Action A non existing device is monitored in the server setting The IP address of the GOT to be monitored is wrong in the client setting Phenomenon Gateway device cannot be monitored Check the PLC CPU device assigned to the gateway device Check the IP address of the GOT to be monitored Confirm the GOT special register GS211 and GS221 and then take the corrective action 3 Section 8 2 1 Error code Error message Confirm the script function error and then take the corrective action GT Designer2 Version Reference Manual An error occurs in the GOT with server function or client function The script function error occurs 8 4 FTP Server Function 8 4 1 Error codes and error messages The error codes and error messages related to the FTP server function are displayed on the FTP client side The error displaying method changes depending on the used FTP client tool The following tables indicate the errors that the GOT sends to the FTP client Normal codes and messages code Description 125 Transfer is started 150 Connection for transfer is established 200 PORT command succeeded Supported command iist 214 HELP display ends HELP display of corresponding command 220 Connection is established 221 User logged out Good Bye Connection ends 226 Connection for transfer ends 230 Login succeeded 250 CWD current directory change command succeeded 957 ee ok
6. ftp gt Is 200 PORT command successful SNAP0001 BMP SNAP0002 BMP 226 Closing data connection ftp gt delete SNAP 0001 BMP 200 Command Okey ftp gt put SNAP0001 BMP 200 PORT command successful 150 Opening connection 226 Closing data connection 250 bytes sent in 0 01 seconds fto gt binary get file name binary quote gtwr J Is J or dir delete file name J put file name 6 Operating the directory of the GOT PC card Create and change the directory in the following procedure D Current directory display cceccceeseeeeeseeeeeeeeeeeeeeseaeeseeeeeaes pwd 2 Selection of the write mode sseeseesseeseessseesierseerrerrnernreeens quote gtwr Directory creatio Messiaan a T mkdir directory name 4 Current directory change ccccccseeeceeeeeceeeeeeeeeeeaeeeeeeseeeeeeaas cd directory name Directory operation image fto gt pwd 257 A snapshot is current directory fto gt quote gtwr 200 command successful fto gt mkdir bmpdata 275 MKD command successful fto gt cd bmpdata 250 CWD command successful fto gt pwd 257 A snapshot bmpdata is current directory ftp gt cd 250 CWD command successful fto gt pwd 257 A snapshot is current directory fto gt Cutting off the line of the GOT and FTP client Cut off the GOT and FTP client in the following procedure 7 BoMia a E quit Logout line cutoff image ftp gt quit 221 User logged out G
7. 2 4 FUNCTION SETTING 4 1to 4 4 4 1 GOT Setting 4 3 4 2 GT Designer2 Setting 4 4 5 SERVER AND CLIENT FUNCTIONS 5 1 to 5 22 5 1 Gateway Devices 5 1 5 1 1 What are the gateway CeVICES cecceccesceeceeceseeeeeeceeeeeeeaecaeeeeseaesaecaeseeeeaeeaeseseaeeateas 5 1 51 2 Usable gateway Jevis a senina Enea ANEN AENEAN EEEE Rk 5 2 5 1 3 How to monitor the gateway GeVICES 0 0 eeeeeeeneeeeeeneeeeeeeaeeeaeeeaeeeaeeeaeeeaeeeaeeeaeeaeeeaeeeas 5 3 5 1 4 PLC devices that can be assigned eccecceceeceeeeeeeeeeeeseeaeeaeeeeeaesaecaeseeeeaesaeenneaeeate 5 6 5 2 Specifications 5 8 5 2 1 SPeOCificAtions eseeccecceceeeeeeeceeeeeeeaeeaecaeseeeeaecaeceeseaesaesaeseeseaesaesaeseseaesaesaeseeeeaesaeseeseneats 5 8 5 2 2 Access range that Can be monitored 00 eeeeeeeneeeeeeeeeeeeeeaeeeaeeeaeeeaeeeaeetaeeeaeeeaeenatenas 5 9 5 3 Setting Method 5 10 5 4 Examples of Use 5 13 5 5 Precautions 5 18 5 6 For Efficient Use 5 20 6 FTP SERVER FUNCTION 6 1 to 6 13 6 1 Specifications 6 1 6 1 1 Specifications nnne nena aa ee a he eae 6 1 6 1 2 File accessible tange oaii anaa araa Renaa RAAR RERNE PARE RA RANAR a ARUNA EKAA RAE AY 6 2 6 2 Setting Method 6 3 6 3 Operation on the FTP Client Side 6 4 6 3 1 Input command at FTP chent dsaiariininiuruintunnis ratai Taasnynnaunioiintun inina iiaii nanias 6 4 6 3 2 File specitying meod esasa 6 5 6 3 3 Checking the line connection condition ce ceceeeeeeeeeeeeseeeeeeeeeeeeaeeaetaeeee
8. 250 TIM50 330 a fl oo ike Bwalo Mitsubishi PLC Omron PLC 5 1 2 Usable gateway devices The usable gateway devices are indicated below Device Range j Representation EGO to EG32767 Specified bits of above word devices Device Name Max Number of Points Word device 32k points Bit device 5 1 3 How to monitor the gateway devices When accessing the gateway devices from the personal computer Using the functions of MX Component e g Microsoft Excel access the gateway devices of the GOTs Refer to the following manuals for the operation method and programming procedure of MX Component L gt MX Component Operating Manual e MX Component Programming Manual The following functions of MX Component are compatible with the GOT Item Open Close ReadDeviceBlock ReadDeviceBlock2 WriteDeviceBlock WriteDeviceBlock2 ReadDeviceRandom ReadDeviceRandom2 WriteDeviceRandom WriteDeviceRandom2 EntryDeviceStatus FreeDeviceStatus OnDeviceStatus SetDevice SetDevice2 GetDevice GetDevice2 GetCpuType Description Opens the communication line starts communication with the GOT Closes the communication line ends communication with the GOT Batch reads data from devices Batch writes data to devices Randomly reads data from devices Randomly writes data to devices Registers device status watching Cancels registering device status watching Announces event Changes the
9. automatic cutoff and manual cutoff Automatic cutoff The GOT cuts off the line automatically if no command is entered from the FTP client within the time set to the watching timer of command input in the FTP server setting The watching timer of command input is always set Refer to the following for the setting of the watching timer of command input lt Section 6 2 Setting Method Manual cutoff Forcibly cutting off the line Using the GOT special register GS400 b2 bit position 2 you can cut off the line forcibly When you want to cut off the line turn ON GS400 b2 bit position 2 Refer to the following manual for details of the GOT special registers L gt GT Designer2 Versioni Reference Manual Point P Precautions for use of GS400 b2 After confirming that the line has been cut off always turn OFF GS400 b2 E Remark About line cutoff Since the GOT cannot detect the fault status of the FTP client it does not cut off the line immediately if the FTP client could not exited properly e g the personal computer was powered off while the line is connecting However as the watching timer of command input has been set the line is cut off automatically in the predetermined period of time 6 4 Example of Use The example of using the FTP server function is described below In this example of use the Windows MS DOS prompt is used to access the GOT and FTP client When performing operation using the commercially ava
10. lt System configuration example gt Utility menu of the GOT Refer to Section 4 1 Set the IP address and mail sending of the GOT itself Int t mail m c on each GOT ntranet mail server E L Ee p 001 1239 Cua a SS GOT PC No oi 164 Personal Cellular ot ee ee ROUTER ADDRESS 000 000 000 000 Li jute P address 10 97 14 20 computer phone SEND HESE HATT 000 nione CO a00 SEND MESSAGE TIME 03 sec 390 START UP TIME 0 0 3 sec o ess Page 2 2 7 SELECT CHANGE EE A Ethernet e GT Designer2 Refer to Section 7 2 lt Mail send setting gt Specify the mail server and set the mail address and Router others of the send destination IP 10 97 14 254 GOT IP address 10 97 14 10 Router address 10 97 14 254 GOT IP address 10 97 14 11 Router address 10 97 14 254 aa Fi ig IP ili EE 10 97 15 254 Please set Setting for the SoftGOT M 1 Available E Mail with the SoftGOT SMTP Server EROM GOT IP address 10 97 15 10 SUBJECT Router address 10 97 15 254 4 1 GOT Setting Perform the GOT setting in the setup of the utility menu Installing the gateway option driver into the GOT or fitting the A9GT J71E71 T to the GOT displays the following menu Make the necessary settings The settings to be m
11. pl Mase v ersi n1 12 shareware Microsoft WindowsNT Workstation4 0 operating system Winbiff Orange Software Microsoft Windows 2000 Professional operating system 7 1 2 Mail send enabled range Since the IP address is used to specify the SMTP server in the mail send function of the GOT a dial up router cannot be utilized to send mail The SMTP server in the Internet service provider cannot be used Install the SMTP mail sever in the intranet SMTP mail server M mn N lll 4 E Personal computer Cellular phone Ethernet M Mail is sent MJ A ee Se M1 ii router Ce GOT ii a ee Personal computer Cellular phone yyy i IEEE PLC aa 7 2 Setting Method Only one mail send setting can be made for one GOT Operation procedure When either of the following operations is performed the Mail dialog box is displayed e Choose the Common gt Gateway Mail menu e Double click Mail in the workspace Mail dialog box wpe Please set Setting for the SoftGOT M Available E Mail with the SoftGOT SMTP Server FROM SUBJECT Item Description Available E Mail
12. A9GT BUSSU A9GT BUS2SU A9GT QBUS2SU cannot be used for the gateway functions Use the above bus connection board when making bus connection k3 The bus connection board A9GT 50WQBUSS A9GT 50WBUSS dedicated to the A956WGOT cannot be used for the gateway functions Use the above bus connection board when making bus connection with the A956WGOT k4 The memory card interface module is required to use the PC card with the A956WGOT or A956GOT k5 The A985GOT cannot use the compact flash PC card It can be used with the A985GOT V only 2 4 Precautions for Mounting the Communication Board How to mount the communication board to the GOT changes depending on the communication board used The precautions for mounting the communication board are described below Point About the mounting of the communication board Do not mount both the bus connection board and serial communication board to the GOT When using the serial communication board When mounting the serial communication board mount it to the GOT as previously Refer to the following manual for the way to mount the communication board A985GOT A975GOT A970GOT A960GOT User s Manual A950GOT A951GOT A953GOT A956GOT User s Manual When using the bus connection board Mount the bus connection board to the back of the A9GT J71E71 T How to mount the bus connection board is shown below 1 Loosen the mounting screws 2 pcs that fix the slot cover on the back of the A9GT J71E71 T
13. Check here when using the mail send function SMTP Server Set the IP address of the SMTP server used FROM Enter the address of the mail send source Alphanumeric characters only SUBJECT Enter the title of the mail Alphanumeric characters only TO Enter the address of the mail send destination Alphanumeric characters only ce Enter the address of the mail send destination copy Alphanumeric characters only mail can be sent if this address is not entered BCC Enter the address of the mail send destination hidden copy Alphanumeric characters only mail can be sent if this address is not entered 1 Since the GOT does not have the mail receive function set the reply destination in FROM when the mail receiver from the GOT will make a reply When there is no specific reply destination set the address as set in TO 2 When mail is to be received from multiple GOTs the GOTs that have sent mail can be identified if you enter different subjects into the GOTs 3 When setting multiple send destination addresses separate them with a space or comma 7 3 Send Examples When e mail is sent from GOT to the target device the reception header part shown at the destination displays a message that shows that the e mail is from GOT Example of display in the reception header part at the destination DEEE KRE From Tig Mii eee CGSHEREE EH neioet AEREE k Subject GOT 01 X Mailer GOT Point P About mail send
14. ON at completion of write GOT 1 PLC 1 z eainiocom rh GOT internal devices GB128 OFF gt ON GB129 OFF gt ON GOT utility menu GOT NET No 1 GOT PC No 1 IP address 10 97 14 1 GT Designer2 server setting EG device Device Points EGO 0 FF GB128 32 EG2 0 FF D100 2 When the bit device that indicates production completion turns ON HR200 value 233 is transferred to EG2 by script 1 GOT utility menu GOT NET No 1 GOT PC No 2 IP address 10 97 14 2 GT Designer2 client setting N W No PLC No IP Address 1 1 10 97 14 1 Bit device that indicates Production completion OFF gt ON PLC 2 device 5 16 Ethernet ii When the bit device that indicates production completion turns ON W200 value 523 is transferred to EG3 by script 2 GOT utility menu GOT NET No 1 GOT 3 GOTPCNo 3 LIP address 10 97 14 3 4 GT Designer2 client setting N W No PLC No IP Address 1 1 10 97 14 1 Bit device that indicates Production completion OFF gt gt ON PLC 3 device 1 GOT 1 setting example a Server setting EG Device Device Type Points EGO O FF _GB128 32 EG2 O FF D100 2
15. device data values Gets the device data values Gets the GOT model When accessing the gateway device from the GOT The gateway devices cannot be assigned to the object functions Hence the script function is used to monitor them The following explains the setting example for access to the gateway device from the GOT 1 When reading the gateway device value Using the script function read the gateway device value of the GOT server function to the internal device of the GOT client function By monitoring the value read to the internal device using the numerical display function or like the GOT client function can monitor the same value as the gateway device value of the GOT server function EGO value is read to GD100 by script function Mitsubishi PLC Gateway device D100 250 EEE GOT internal device EGO Omron PLC Be TI GD100 330 Assignment definition TIM50 330 EGO TIM50 Ethernet GOT client function Script function Client setting Numerical display 1 for Mitsubishi Numerical display 2 for GOT internal device GOT server function Server setting D100 250 g ill oio of Mitsubishi PLC Omron PLC The read destination of the script function can be set to the device of the Mitsubishi Electric PLC a Setting items of the G
16. dialog box Cancel Used to cancel the settings and close the dialog box Add Used to add new assignment settings Click this switch to display the EG Device setting dialog box and make settings Delete After selecting the setting click this switch to delete the setting Delete All Used to delete all settings Used to check whether the settings are correct or not Check If any setting is incorrect the error message is displayed 2 Precautions for device assignment A gateway device is set on a two point basis Hence the number of assigned points changes depending on the set device type a Assignment of bit device 1 bit device It is assigned on a 32 point basis Example When M0 is assigned to EGO Eco istomo jan Msztomie c Assignment of word device 32 bit device It is assigned on a 1 point basis Example When CN200 32 bits is assigned to EGO EGO CN200 lower bits EG1 CN200 upper bits 5 11 b Assignment of word device 16 bit device It is assigned on a 2 point basis Example When DO 16 bits is assigned to EGO d Assignment of 8 bit device It is assigned on a 4 point basis Example When E0000 is assigned to EGO EGO E0001 E0000 EG1 E0003 E0002 5 11 Client setting In the client setting register the N W No PLC No and IP address of the GOT of the server function to be monitored by the GOT of the client function 1 Client function setting method a Operation procedure When eit
17. system Microsoft WindowsNT Workstation4 0 operating system Microsoft Windows 2000 Professional operating system FFFTP freeware NextFTP Ver 2 shareware 6 1 2 File accessible range The FTP server function can access on the PC card of the GOT within the network to which the FTP client is connected Multiple clients cannot access the PC card of the GOT simultaneously When using a relay device such as a router consult the network manager Personal computer FTP client C Ethernet gi GOT C FTP server function Lar Ji i PLC Router 1 GOT FTP server function TEEL G Simple judgment of whether file access is possible or not Simple judgment of whether file access is possible or not can be made by issuing the ping command to the GOT Example of issuing the ping command Windows MS DOS prompt IP address of GOT 10 97 14 10 e When file can be read C ping 10 97 14 10 pinging 10 97 14 10 with 32 byte of data reply from 10 97 14 10 bytes 32 time lt 10ms ttl 128 reply from 10 97 14 10 bytes 32 time lt 10ms ttl 128 reply from 10 97 14 10 bytes 32 time lt 10ms ttl 128 CA e When file cannot be read C ping 10 97 14 10 pinging 10 97 14 10 with 32 byte of data request
18. the FTP client to the file in the PC card of the GOT Doing so may damage the data in the PC card 6 12 6 12 8 If you reset the GOT or switch power off while the line of the GOT and FTP client is connecting the operation of the FTP client depends on the specifications of the FTP client tool used Use the FTP client tool that supports the detection of an FTP server fault or that can be exited properly 9 Access to a file cannot be made if the memory card access switch of the GOT is OFF 10 Write processing put cannot be performed if the write protect switch of the GOT is ON 11 The GOT does not use any file whose file name is 8 or more characters long Hence if the PC card contains a file whose file name is 9 or more characters long it cannot be accessed from the FTP client Set the file name of a file to be accessed to within 8 characters except a period and extension 12 Depending on the used FTP client tool the time stamp may differ from that of the file in the PC card of the GOT If the time stamp differs check the setting of the FTP client tool Precautions for FTP login 1 If you have forgotten the password for FTP login connection to the GOT cannot be made You can confirm the set password on GT Designer2 2 You cannot log in to the GOT from multiple FTP clients simultaneously 6 13 6 13 pi 7 MAIL SEND FUNCTION This chapter describes the mail send function Point 1 About the mail softwar
19. the GOTs If the PLC CPU of a different maker is monitored use of the server function enables data to be read written with only MX Component and the communication method to be standardized by Ethernet Previously When server function is used Install peripheral software 3 programs of various companies i z Necessary software NN mT is MX Component only j dic l ae MX Component Communication method is standardized by Ethernet O Ethernet M Ti 2 T i E Mitsubishi Company Micro computer A board Communications are made with personal computer in respective communication methods of companies Fa Server Server Server Bus communi RS 232C RS 232C Bus communi RS 232C RS 232C cation communi communi cation communi communi RS 232C cation cation RS 232C cation cation communication RS 422 RS 422 communication RS 422 RS 422 RS 422 communi communi RS 422 communi communi communication cation cation communication cation cation yy
20. to b13 Reserved b14 Turns ON when an error occurs in the server function b15 Turns ON when an error occurs in the client function b Gateway common control GS400 bO to b1 Fixed at OFF b2 Turns ON to cause forced logout in the FTP server function b3 to b10 Fixed at OFF b11 Turns ON to clear the error of the mail send function GS200 b11 GS201 to GS206 b12 to b13 Fixed at OFF b14 Turns ON to clear the error of the server function GS200 b14 GS210 GS211 b15 Turns ON to clear the error of the client function GS200 b15 GS220 GS221 8 3 Server and Client Functions 8 3 1 Error codes and error messages GOT error code list The following table lists the error codes that are stored into the GOT special registers GS211 server function error code and GS221 client function error code Error Code 490 491 492 493 Definition and Cause Corrective Action 1 Set the other GOT as the monitor destination in the script device of the GOT itself using the script function 2 Do not use the script but directly monitor the PLC devices An attempt was made to access a non existing Check the network number PLC station number and Ethernet station settings of the monitor destination 1 Increase the send time out period in the utility menu of the GOT 2 Check the network Check firewall presence absence execute Ping for example 1 Check for cable disconnection and check the mo
21. 1 The format and contents of the display of e mail sent vary depending on the mailer specifications used at the destination 2 When e mail is sent to a mobile phone the display may vary depending on the specifications screen size of the mobile phone 3 GOT can send up to 16 e mail at one time If alarms occur 17 times or more the 17th e mail and subsequent are not sent When sending e mail using the alarm history display function If an alarm occurs in GOT the time and information of the alarm are sent to the destination by e mail Moreover if the alarm recovers the time and information of the alarm recovery are sent to the destination by e mail Refer to the following manual for the way to set the alarm history display function lt gt GT Designer2 Versioni Reference Manual 1 Example of display at the destination when an alarm occurred Alarm history occurred information Occur Time 2002 11 28 09 48 15 a Occur Information Line A supply conveyor stopped b detailed Information Alarm history A line supply converter stopped Check the power source a The comment entered in the alarm history display function is displayed b The content of detailed display entered in the alarm history display function is displayed Detail Information is not displayed if the detail display setting of the alarm history display function has not been made or has been made for the base or window screen Alarm hist
22. 2K ok ok 2k ok ok ok 2K K k k ok IS Current Current directory display directory MKD command sucess MKD directory creation command 275 MKD command successful succeeded 331 Password is required Abnormal codes and messages Error code Description 426 Transfer error 500 Syntax error command cannot be recognized Unsupported command 510 Port open failed File open failed 530 Login failed 550 Command execution failed 8 4 2 Troubleshooting The following table indicates the troubleshooting for use of the FTP server function Phenomenon Definition and Cause Use FTP server function is not checked in the FTP server setting of GT Designer2 The oth ice has logged in to the GOT Line cannot be connected e oiher device has ogg Login cannot be made The login name or password is wrong The file name is 9 or more characters long The reference mode is selected Overwrite disable or similar setting has been made in the FTP client setting File cannot be written The file of the same name exists The PC card is write protected The memory card access switch of the GOT is OFF An attempt was made to read the file that does not exist The memory card access switch of the GOT is OFF The PC card is write protected The memory card access switch of the GOT is OFF File cannot be read File cannot be deleted GOT was powered off during login FTP client software was forcibly exited during login
23. 4DR H 20DT H 28DT H 40DT H 64DT type HL 40DP HL 64DR EH 150 series EH CPU104 EH CPU208 EH CPU308 EH CPU316 FPO C16CT FP0 C32CT FP1 C24C FP1 C40C i FP2 FP2SH FP2 CCU FP3 Matsushita Electric Works PLC FPS FP10 S FP10SH FP M C20TC FP M C32TC About the Symbols In this manual the following symbols are used to represent menus and buttons Description Represents the menu item to be selected from the menu bar Represents the item in the setting dialog box or the utility menu item of the GOT Represents the operation sequence D to to KES Represents the item that provides detailed explanation manual or the chapter section or item of that manual Represents the information that you should know Represents the information that will be useful Represents the supplementary explanation that will be helpful 1 OVERVIEW This manual explains the gateway functions that can be performed on the GOT A900 series There are the following gateway functions to support remote watching and remote maintenance of production sites from an office e Server function e Client function FTP server function e Mail send function 1 1 Features of Server and Client Functions Collection of data by personal computer server function Monitoring the GOTs servers from the personal computer MX Component allows data to be read written indirectly from to the PLC CPU devices being monitored by
24. 92 occurs in GOT of client function This error may occur when there are many clients that access the server To increase the send time out period set the value of already set send time out period xnumber of clients 5 If error code 15 script was not terminated after elapse of script watching time was stored into the script error data GS16 to GS47 when script that used gateway devices was used This error may occur when there are many clients that access the server To increase the script watching time GS385 set the value of already set script watching time xnumber of clients Refer to the following manual for details of the script function lt GT Designer2 Versioni Reference Manual MX Component error code list The following table lists the error codes that may occur when access is made from MX Component to the GOT Error Code Definition and Cause Corrective Action 1 Corrective action for MX Component e Reexamine the time out value in Properties e Make the communication setting again in the communication setting utility e Reexamine the PLC CPU module setting cable status and others Exit from MX Component once and execute it again e Exit from the program and restart the DOS V personal computer lt 3 MX Component Programming Manual Time out error Time out period elapsed but data could not be received 0x 0180840B 2 Corrective action for GOT e Check whether the server setting of GT Design
25. Can monitor the PLC CPU device 1 Can monitor the PLC CPU device assigned to the gateway device of the GOT 1 2 Can monitor the PLC CPU device assigned to the gateway device of the GOT 2 x Cannot monitor Personal computer GOT 1 client GOT 2 client 5 3 Setting Method Server setting In the server setting set the gateway device to be used by the GOT of the server function and the PLC CPU device to be assigned to that gateway device 1 Server function setting method a Operation procedure When either of the following operations is performed the Gateway server dialog box is displayed e Choose the Common gt Gateway Server menu e Double click Gateway Server in the workspace b Gateway server dialog box EG Device Layout Item Description Set the gateway devices used for the GOT of the server function and the PLC CPU devices to be assigned to those gateway devices EG Device Set the gateway device to which the PLC CPU device will be assigned Type Select the type of the device to be assigned Set the N W number PLC station number CPU number and device of the PLC CPU to be assigned to the gateway device PLC Device Refer to the following for the device setting method L gt GT Designer2 Versioni Reference Manual Assignment setting list Points Register the consecutive device points in Points for the device type already set OK Used to confirm the settings and close the
26. Corrective Action Check Use FTP server function After the other device has logged in connect to the line again Issue the Ping command to the GOT and check for a reply Ask the manager for confirmation Enter the correct login name or password Case sensitive Reduce the file name to 8 characters extension Change to the write mode Reexamine the FTP client setting Delete the file or change the file name so that the file of the same name does not exist Cancel the write protection of the PC card Turn ON the memory card access switch of the GOT Check for the file using the dir or Is command Turn ON the memory card access switch of the GOT Cancel the write protection of the PC card Turn ON the memory card access switch of the GOT Since the file being transferred may have been corrupted do not use but delete it The operation of the FTP client changes depending on the specifications of the FTP client Log in to the GOT again after the time set to the watching timer of command input in the FTP server setting has elapsed The GOT logs out after the time set to the command has elapsed 8 5 Mail Send Function 8 5 1 Error codes and error messages The following table indicates the error codes stored into the GOT special register GS202 mail send function error code Definition and Cause The FROM address has not been set The SMTP server has not been set The send destination address h
27. D V A985GOT TBD A975GOT TBD B A970GOT TBD B A970GOT SBD A970GOT SBA EU A970GOT A960GOT EBD A956GOT SBD A956GOT SBD M3 A953GOT SBD A953GOT SBD M3 A951GOT SBD A951GOT SBD M3 A951GOT QSBD A951GOT QTBD M3 _A951GOT QSBD M3 A950GOT SBD A950GOT SBD M3 A985GOT TBA EU A975GOT TBA A975GOT TBD A970GOT TBD A970GOT LBD A970GOT TBA A970GOT LBA A970GOT LBA EU A960GOT EBA EU A956GOT LBD A956GOT LBD M3 A953GOT LBD A953GOT LBD M3 A951GOT LBD A951GOT LBD M3 A951GOT QLBD A951GOT QLBD M3 A950GOT LBD A950GOT LBD M3 A950GOT SBD M3 H A950GOT LBD M3 H A953GOT SBD M3 H A953GOT A951GOT A951GOT Q A950 handy GOT Description A9GT QBUS2S A9GT BUSS A9GT BUS2S A9GT RS2 A9GT RS2T A9GT 50WRS2 Description E Option Generic Term Abbreviation Option E Software Memory board PC card memory card Flash PC card ASGTMEM 10MF Compact card Generic Term Abbreviation GT Works2 Version1 GT Designer2 Version1 Description A9GT FNB A9GT FNB1M A9GT FNB2M A9GT FNB4M A9GT FNB8M A9GT QFNB A9GT QFNB4M A9GT QFNB8M Flash PC card Commercially available flash PC card SRAM type PC card ASGTMEM 20MF A9GTMEM 40MF flash PC Commercially available flash PC card Description SW1D5C GTWK2 E SW1D5C GTD2 E Software GT Designer2 GT Designer2 screen creation software for GOT900 GT Sim
28. FTP server function cccccceesseeeeeseeeeees 8 7 Mail send fUNCtiON ccccceeeeeeesseeeeees 8 9 Server and client functions 8 4 Example of use FTP server function cccccceesseeeesteeeeees 6 8 Mail send fUNCtION ccccceesteeeeeteeeeees 7 6 Server and client functions c ccee 5 13 F Features of FTP server function 0 1 3 Features of mail send function 00 1 3 Features of server and client functions 1 1 File specifying Method eeeeeseseeeeeeeeeees 6 5 FTP Server setting ceceeceeeceeeeeseeeeeeeteeeeees 6 3 FUNCTION setting eeeeeceeeeeeeeneeeeeeeeeeeteeeeees 4 1 G Gateway information c ceceeeeeeteeeee 8 2 GOT setting sss ceciees ennai 4 3 GT Designer2 Setting c ceeeeeeeeereeeeees 4 4 H How to monitor the gateway devices 5 3 Input command on FTP client side 6 4 L Line cUtof feniero 6 7 Index 1 M Mail send enabled range s es 7 2 Mail send setting eee eeeeeeeeeeeeeeeeeeeeeeeeeees 7 3 O Operation on FTP client Side ceeeee 6 4 Operation SEQUENCE ccceeceeeteeseeseeteeeteees 3 1 P PLC devices that can be assigned 5 6 Precautions FTP Server fUNCTtION c ccccccsseeeesseeeeees 6 12 Mail Send function ccccceesseeesteeeeeeees 7 8 Server and client functions eee 5 18 Precautions f
29. However if repairs are required onsite at domestic or overseas location expenses to send an engineer will be solely at the customer s discretion Mitsubishi shall not be held responsible for any re commissioning maintenance or testing on site that involves replacement of the failed module Gratis Warranty Term The gratis warranty term of the product shall be for one year after the date of purchase or delivery to a designated place Note that after manufacture and shipment from Mitsubishi the maximum distribution period shall be six 6 months and the longest gratis warranty term after manufacturing shall be eighteen 18 months The gratis warranty term of repair parts shall not exceed the gratis warranty term before repairs Gratis Warranty Range 1 The range shall be limited to normal use within the usage state usage methods and usage environment etc which follow the conditions and precautions etc given in the instruction manual user s manual and caution labels on the product 2 Even within the gratis warranty term repairs shall be charged for in the following cases 1 Failure occurring from inappropriate storage or handling carelessness or negligence by the user Failure caused by the user s hardware or software design 2 Failure caused by unapproved modifications etc to the product by the user 3 When the Mitsubishi product is assembled into a user s device Failure that could have been avoided if functions or stru
30. MITSUBISHI GOT A900 Series Operating Manual GT Works2 Version1 GT Designer2 Versioni compatible Gateway Functions Manual eratio 900 series MITSUBISHI Graphic Operation Terminal e SAFETY PRECAUTIONS e Always read these instructions before using this equipment Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The instructions given in this manual are concerned with this product For the safety instructions of the programmable controller system please read the CPU module user s manual In this manual the safety instructions are ranked as DANGER and CAUTION N Indicates that incorrect handling may cause hazardous conditions a DANGER resulting in death or severe injury CAUTION Indicates that incorrect handling may cause hazardous conditions resulting in medium or slight personal injury or physical damage Note that the CAUTION level may lead to a serious consequence according to the circumstances Always follow the instructions of both levels because they are important to personal safety Please save this manual to make it accessible when required and always forward it to the end user Precautions for test operation A CAUTION e Before starting test operation for system monitor special function module monitor or ladder monitor bit devic
31. N A173UHCPU A173UHCPU S1 FA controller LM610 LM7600 LM8000 MELDAS C6 C64 FCA C6 FCA C64 E Other PLC Generic Term Abbreviation Description C200HS C200H C200H amp series C200HX C200HG C200HE CQM1 C1000H C2000H Omron PLC CV500 CV1000 CV2000 CVM1 CPU01 CVM1 CPU11 CVM1 CPU21 CS1 CS1D CJ1M CPM1 CPM1A CPM2A CPM2C CPM1H GL60S GL60H GL70H GL120 Yaskawa PLC GL130 CP 9200SH CP 9300MS MP 920 MP 930 MP 940 MP 9200 H PROGIC 8 SLC500 series SLC500 20 SLC500 30 SLC500 40 SLC5 01 SLC5 02 SLC5 03 SLC5 04 SLC5 05 Allen 1761 L10BWA 1761 L10BWB 1761 L16AWA 1761 L16BWA Bradley MicroLogix1000 1761 L16BWB 1761 L16BBB 1761 L32AWA 1761 L32BWA PLC series 1761 L32BWB 1761 L32BBB 1761 L32AAA 1761 L20AWA 5A 1761 L20BWA 5A 1761 L20BWB 5A Eee 500 1764 LSP series JW 21CU JW 22CU JW 31CUH JW 32CUH Sharp PLC JW 33CUH JW 50CUH JW 70CUH JW 100CUH JM 100CU Z 512J i PROSEG 1 T3 T3H T2E T2N Toshiba series ven hi Model3000 S2T SIMATIC S7 200 series SIMATIC S7 300series SIEMENS ETS SIMATIC S7 400 series Large sized H H 302 CPU2 03H H 702 CPU2 07H H 1002 CPU2 10H H 2002 CPU2 20h series H 4010 CPU3 40H H 300 CPU 03Ha H 700 CPU 07Ha H 2000 CPU 20Ha HITACHI H 200 to 252 H 200 CPU 02H CPE 02H H 250 CPU21 02H PLC saries H 252 CPU22 02h H 252B CPU22 02HB HIDEC H H 252C CPU22 02HC CPE22 02HC rieo bined board H 20DR H 28DR H 40DR H 6
32. OT client function e Script function 0 0 eee Make setting to read the gateway device value of the GOT server function to the internal device of the GOT client function e Client Setting cece Register the GOT of the server function whose device value will be read e Numerical display 1 function Make setting to display the device value of the Mitsubishi Electric PLC e Numerical display 2 function Make setting to display the internal device value of the GOT client function b Setting item of the GOT server function e Server Setting Make setting to assign the device of the Omron PLC to the gateway device 2 When writing a value to the gateway device Using the numerical input function or like write a value to the gateway device of the GOT client function Using the script function write the internal device value of the GOT client function the gateway device of the GOT server function GD100 value is written to EGO by script function Ethernet Mitsubishi PLC GOT internal device Gateway device D100 250 GD100 520 EGO Assignment ren REG W definition TIM50 520 EG0 TIM50 GOT client function Script function Client setting Numerical display 1 for Mitsubishi Numerical display 2 for GOT internal device D100 250 A YH Teg The write destination of the script function can be set to the GOT internal device of the s
33. ade change depending on the gateway functions used Refer to the following manual for the way to operate the utility menu L gt GOT A900 Series Operating Manual GT Works2 Version1 GT Designer2 Version compatible Extended Option Functions Manual GOT PC No o1 164 GOT IP ADDRESS 000 000 000 000 GOT PORT No 05001 1024 65534 ROUTER ADDRESS 000 000 000 000 FoweR SUBNET MASK 255 255 255 000 SEND MESSAGE WAIT 000 x10ms 0300 SEND MESSAGE TIME 03 sec 3 90 START UP TIME 0 0 3 sec o ess Page 2 2 7 lt SELECT CHANGE XY aS Setting required Setting required depending on condition Setting not required no problem will arise if setting is made FTP A ane f Server Client Mail Send Setting Item Description Factory Setting h Server A Function Function Function Function GOTNETNO Setthe network No ottheGOT 1 OT of GOT PC NO Setthe station numberoftheGot 1 OO GOT IP ADDRESS Set the IP address oftheGoT ooo o0o 000 000 GOTPORTNO __ SettheportNo oftheor so ROUTER When the system is connected to the other ADDRESS 2 network by a router set the router address of 000 000 000 000 O the network where the GOT is connected When the GOT is connected to the Ethernet network under control of the subnet set the SUBNET MASK subnet mask set commonly to the networks 255 255 255 000 O When the subnet is n
34. ansaction permission Specifications subject to change without notice
35. as not been set Error Code 2 10 11 12 The mail address is incorrect The number of alarms that occurred may be greater than the number of alarms that can be sent by mail The SMTP server could not be connected Time out occurred at the time of connection with the SMTP server Error notification is given from the SMTP server Corrective Action Set FROM Mail send setting on GT Designer2 Set the SMTP server Mail send setting on GT Designer2 Set the send destination TO Mail send setting on GT Designer2 Check whether the mail address settings of FROM TO CC and BCC are correct Mail send setting on GT Designer2 Check the number of alarms that occurred Max number of queuing alarms 16 1 Check whether the SMTP server is normal or not 2 Check whether the IP address setting of the SMTP server is correct or not Mail send setting on GT Designer2 3 Ask the network manager about the router address and sub net mask and set the returned data in the setup of the GOT 4 When a firewall has been built on the network ask the network manager if it has been set to pass through the port 25 1 Check whether the SMTP server is normal or not 2 Increase the send message time value Setup screen of GOT 1 Check whether the SMTP server is normal or not 2 Ask the network manager if mail can be sent without certification e g POP3 certification 8 5 2 Troubleshooting The follo
36. ata CSV file are written to PC cards Ethernet M PC card FTP server PC card ee FTP server PC card FTP server gt T function a function A 7 function Bus communication RS 232C communication RS 422 communication jab i il e Mitsubishi PLC RS 232C communication RS 232C communication RS 422 communication RS 422 communication EE in fe ET Company A PLC Micro computer board 1 3 Features of Mail Send Function Using the alarm history display function you can send the occurrence or restoration information of an error to the personal computer or cellular phone by mail at occurrence of or restoration from the error Intranet mail server i Mail send function Bus communication Alarm history display function Sends alarm occurrence or restoration information LI Personal Cellular computer phone RS 232C communication Mitsubishi PLC a RS 422 communication Ethernet _ Mail send Mail send function function RS 232C communication RS 232C communicat
37. bes the settings common to the gateway functions Chapter 4 Functions Cha ter 5 Server and Client Describes the specifications setting methods precautions and p Functions others of the server and client functions Describes the specifications setting methods precautions and FTP Server Function Chapter 6 others of the FTP server function D ibes th ifications setting methods precautions and Mail Send Function escribes the specifications setting p Chapter 7 others of the mail send function Describes the error messages and troubleshooting for the Troubleshooting I Chapter 8 functions INTRODUCTION Thank you for choosing the Mitsubishi Graphic Operation Terminal Before using the equipment please read this manual carefully to use the equipment to its optimum CONTENTS SAFETY PRECAUTIONS A 1 REVISIONS A 2 Structure of This Manual A 3 INTRODUCTION A 4 About Manuals A 7 About the Generic Terms and Abbreviations A 8 About the Symbols A 11 1 OVERVIEW 1 1to 1 3 1 1 Features of Server and Client Functions 1 1 1 2 Features of FTP Server Function 1 3 1 3 Featuers of Mail Send Function 1 3 2 SYSTEM CONFIGURATION 2 1 to 2 4 2 1 System Configuration of Gateway Functions 2 1 2 2 Connection Form 2 1 2 3 Required Devices 2 2 2 4 Precautions for Mounting the Communication Board 2 2 2 5 About the System Programs 2 4 2 6 Precautions for System Configuration 2 4 3 OPERATION SEQUENCE 3 1 to 3
38. correspondences between the commands that can be used with a general FTP client tool and the FTP server function of the GOT The usable commands change depending on the FTP client tool used For details refer to the manual of the used FTP client tool Usable x Unusable A Setting invalid command does not result in error Command ancien Reference Write Name Mode Mode Additionally writes a file to the GOT PC card x Changes the file transfer mode to the ascii mode A Changes the file transfer mode to the binary mode o Exits the FTP client tool o Changes the current directory of the GOT PC card ee Cuts off the line withthe GOT d oo i Reads the file information in the GOT PC caro ooi Reads a file from the GOT PC card ooo i O Ooi Displays file names in the GOT PC card ii ai Reads the file information in the GOT PC card to the specified file o Reads multiple files O oOo o Reads the file names in the GOT PC card to the specified file O o Connects the ine withthe GOT i O Ooi Creates the current directory ofthe GOT ooi Cuts off the line with the GOT to exit the FTP client too O o o o Used when the GOT dedicated command is used Example quote gw O Enters the user name and password used to log in to the GOT o 1 Since this command is fixed to No file conversion binary in the FTP server function it is invalid if set 2 The rename and rmdir comman
39. cted such as in aircraft medical applications incineration and fuel devices manned transportation equipment for recreation and amusement and safety devices shall also be excluded from the programmable logic controller range of applications However in certain cases some applications may be possible providing the user consults their local Mitsubishi representative outlining the special requirements of the project and providing that all parties concerned agree to the special circumstances solely at the users discretion Microsoft Windows Microsoft Windows NT are registered trademarks of Microsoft Corporation in the United States and other countries Pentium is a registered trademark of Intel Corporation in the United States and other countries Other company and product names herein are either trademarks or registered trademarks of their respective owners SPREAD Copyright C 1998 Farpoint Technologies Inc GOT A900 Series Operating Manual GT Works2 Version1 GT Designer2 Version1 compatible Gateway Functions Manual MODEL SW1 GTD2 O G E MODEL 1DM208 SH NA 080398E C 0407 MEE sfa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE 1 8 12 OFFICE TOWER Z 14F HARUMI CHUO KU 104 6212 JAPAN NAGOYA WORKS 1 14 YADA MINAMI 5 CHOME HIGASHI KU NAGOYA JAPAN When exported from Japan this manual does not require application to the Ministry of Economy Trade and Industry for service tr
40. ction iy ir server function a ERN e ne i Mitsubishi Electric PLC Allen Bradley PLC Remark Restricted script function commands There are restrictions on the following script function commands Refer to the following manual for details of the commands lt GT Designer2 Versioni Reference Manual e Word device specified command names Description Applied Function arithmetic operation sin cos tan asin acos atan abs log logi0 exp Idexp sqrt e Bit device specified command names Description Substitution Device operation set rst alt Operator 5 2 Specifications The specifications of the server and client functions are given below Recommended Max 64 units Max number of nodes GOT server function GOT client function personal computer that communicates with GOTs 64 units Number of clients GOT personal computer that can access servers Max 5 units 7 GOTs simultaneously Other node designation IP address designation max 128 units i gt GT Designer2 Gateway device 32k points of word devices EGO to 32767 Compatible MX Component MX Component Version 3 SW3D5C ACT A or later Memory space Server function 20 20 x number of assigned gateway device points used by GOT GT Designer2 bytes 16 20 x preset number of GOTs of server funct
41. ctures judged as necessary in the legal safety measures the user s device is subject to or as necessary by industry standards had been provided 4 Failure that could have been avoided if consumable parts battery backlight fuse etc designated in the instruction manual had been correctly serviced or replaced 5 Failure caused by external irresistible forces such as fires or abnormal voltages and Failure caused by force majeure such as earthquakes lightning wind and water damage 6 Failure caused by reasons unpredictable by scientific technology standards at time of shipment from Mitsubishi 7 Any other failure found not to be the responsibility of Mitsubishi or that admitted not to be so by the user 2 Onerous repair term after discontinuation of production 1 Mitsubishi shall accept onerous product repairs for seven 7 years after production of the product is discontinued Discontinuation of production shall be notified with Mitsubishi Technical Bulletins etc 2 Product supply including repair parts is not available after production is discontinued 3 Overseas service Overseas repairs shall be accepted by Mitsubishi s local overseas FA Center Note that the repair conditions at each FA Center may differ 4 Exclusion of loss in opportunity and secondary loss from warranty liability Regardless of the gratis warranty term Mitsubishi shall not be liable for compensation of damages caused by any cause found not to be the respo
42. d Gateway Client NIW No PLCNo Type TP address 1 2 cor 1097 142 1 s or usm Port No Communication Lx A FTP server function lt System configuration example gt Utility menu of the GOT Refer to Section 4 1 Set the IP address of the GOT itself on each GOT y i j aed ai General purpose FTP client tool TEEGEE Windows MS DOS prompt or command prompt ROT PEN gt Oh eA IP address 10 97 14 20 ROUTER ADDRESS 000 000 000 000 SUBNET MASK 255 255 255 000 g Ethernet M SEND MESSAGE TME 09 Sec 3290 START UP TIME 0 0 3 sec o ess Page 2 2 T SELECT CHANGE ao oe A e GT Designer2 Refer to Section 6 2 GOT IP address 10 97 14 10 GOT IP address 10 97 14 11 Router address 10 97 14 254 Router address 10 97 14 254 ip ig g71a054 SFTP Server setting gt Set the login name and password used for connection Router f the li f th d GOT nee of the line of the personal computer an 4 FTP x L IV Use FTP Function Login Name E 07900 GOT IP address 10 97 15 10 Password eoTs00 watching timer of command input 15 Min Cancel Router address 10 97 15 254 Mail send function
43. devices it may take some time to cancel When the execution of automatic screen save has been specified it may take more time than the specified For example when the script processing time is 2 seconds the screen save is canceled in a maximum of 2 seconds after the screen is touched 5 6 For Efficient Use This section explains the points for efficient use of the server and client functions Script function setting When the gateway devices are used directly to execute a program the number of times to access the other GOT increases slowing the processing By performing batch read from the GOT internal devices and performing batch write after execution of the processing as shown in the following 1 the number of access times can be decreased improving the processing speed 1 When performing batch read from GOT internal devices GD and performing batch write after processing Access to the other station GOT occurs twice 1 3 When one time of access requires 50ms the necessary processing time is about 100ms Script description example bmov 1 2 w EGO w GD100 10 w D200 w GD100 1 1 w D201 w GD101 3 w D202 w GD102 EGO to EG9 GD100 to GD109 w D203 w GD 103 Server Client w D204 w GD1 04 2 Processing 2 w GD105 128 w GD106 w D106 a ly 3 w D205 w GD107 2 iE w D206 w GD1 08 w GD109 5433 3 bmov w GD100 1 2 w EGO 10
44. ds are unusable ololololololololololololololololololo lo lo GOT dedicated commands When the line with the GOT is connected the FTP client is in the reference mode in which only file read is enabled Before executing file write delete or directory creation change it to the write mode To select the reference mode or write mode issue a mode change command Usable A Setting invalid command does not result in error mand quote gtwr Changes the FTP server function mode of the GOT to the write mode o A quote gtrd Changes the FTP server function mode of the GOT to the reference mode i OQ Displays the general purpose actual commands of the FTP protocol supported by the quote help play g purp p pp y EJ FTP server function of the GOT 6 3 2 File specifying method There are two file specifying methods one is to specify one file directly and the other is to specify multiple files that meet the condition Specifying the file name to read Specify the file name period and extension of the file to be specified Filename Extension Represents the file type Separates the file name and extension The file name to be read The FTP server function mainly uses files having the following extensions Extension Application on GOT csv Recipe file recipe function alarm history file alarm history display function bmp p Monitor screen image hardcopy function Jpg Specifying the files t
45. dule mounting status 2 Check the network Check firewall presence absence execute Ping for example A communication time error occurred A communication error occurred The error that will occur in the GOT of the server function is the error code 493 only Point 1 If error code 493 occurs in GOT of server function This error may occur when networks coexist If no error has occurred on the target client side it poses no specific problem since communication is restored to normal by the retry processing on the client side 2 System that uses a router If the error code 493 occurred in the GOT of the server function note that the IP Ethernet T address of the target client is the address of the router At 493 error not the IP address of the client but the IP address of the router 10 97 14 254 is stored into the GOT internal device IP 10 97 15 254 Server Router GOT IP address 10 97 14 10 IP 10 97 15 254 LI Client GOT IP address 10 97 15 10 3 If an error occurs in the GOT with client function If an error occurs in the GOT with client function the script will stop Take the corrective action and then re execute the script Refer to the following manual for details of Script function lt GT Designer2 Versioni Reference Manual 4 If error code 4
46. e The GOT send source does not require mail software 2 About the system when using the mail send function The SMTP mail server must be installed in the intranet to use the mail send function 7 1 Specifications The specifications of the mail send function are given below Item Specifications Setting Method IP address setting 1 server only Fixed SMTP server Fixed Server certification Disabled c 1 to 32 max 64 characters for 1 address Alphanumeric Send To AN characters only r destination GT Designer2 Address 0 to 32 max 64 characters for 1 address Alphanumeric characters only Subject Max 128 characters alphanumeric characters only GT Designer2 Either of the following two different comments can be sent Alarm comment Max 512 characters alphanumeric characters Text data size Detailed comment Max 512 characters alphanumeric characters Attached file Disabled Encoding No 20 4x number of destinations 2 2 x total number of Memory space used by GOT bytes z et GT Designer2 destination subject and sender characters The following table indicates the mail software programs that have been confirmed to operate properly by Mitsubishi Electric Name Maker Compatible OS OutlookExpress5 Microsoft Windows 95 operating system BAN Netscape Communicator 4 7 or later Microso ee 98 operating system f Re i Microsoft Windows Millennium Edition operating system
47. e ON OFF word device present value changing timer counter set value present value changing buffer memory present value changing please read the manual carefully to fully understand the operation methods For the devices that perform significant operations for the system never perform test operation to change data Doing so can cause accidents due to false outputs or malfunctions REVISIONS The manual number is given on the bottom left of the back cover SH NA 080398E A Jan 2004 SH NA 080398E B Chapter 4 Section 5 4 Jul 2004 SH NA 080398E C Partial corrections Section 5 5 MODEL CODE change Changed from 1D0J00 to 1DM208 Japanese Manual Version SH 080352 C This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property ights which may occur as a result of using the contents noted in this manual 2003 MITSUBISHI ELECTRIC CORPORATION Structure of This Manual This manual is made up of the following chapters Chapter 1 Overview Describes the features of the gateway functions Chapter 2 System Configuration Describes the system configuration of the gateway functions Chapter 3 Operation Sequence Provides the general procedure for using the gateway functions Settings Common to Descri
48. eeaeeaeeaetenteaeeas 6 6 OS A IME CULOTT a5 ies dace ht Secs cS vee eet E ceed ane cee eee eat oe eee at ee ee 6 7 6 4 Example of Use 6 8 6 5 Precautions 6 12 7 MAIL SEND FUNCTION 7 1to 7 8 7 1 Specifications 7 1 7A SPCCHICATIONS ae ktik EART E AA dsl te ieee titel A AAE 7 1 7 1 2 Mail send enabled range eeceeceesceescesseeeeeeeeeeeeeeeeeeseeeeeeeeeeeeeeeeeeeeeeeseeeseeeseeeseeeeses 7 2 7 2 Setting Method 7 3 7 3 Send Examples 7 4 7 4 Examples of Use 7 6 7 5 Precautions 7 8 8 TROUBLESHOOTING 8 1 to 8 9 8 1 Troubleshooting Common to Gateway Functions 8 1 8 2 Gateway Information 8 2 8 3 Server and Client Functions 8 4 8 3 1 Error codes and error MESSAGES eeeeceeeeeeeeeeeeeeeeeeaeeeeeeeaeeeaeeeaeeeaeeeaeeeaeeaeeeaeeeaeeeaeenas 8 4 8 3 2 Troubleshooting Asi ian a ar aAa Ca aai aAa Aa DAAI IAAT T DARS AAAA A AAP A 8 6 8 4 FTP Server Function 8 7 8 4 1 Error codes and error MESSAGES eeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeaeeeaeeeaeeeaeeeaeeeaeeaeeeaeeeaeeeaeenas 8 7 8 42 TT roublESNOOLING ii iste nee nite oie AAR a a EAR ARARE ARA AEA a ieee E EARRA 8 8 8 5 Mail Send Function 8 9 8 5 1 Error codes and error MESSAGES eeeeceeeceeeeeeeeeeeeeeeneeeaeeeaeeeaeeeaeeeaeeeaeeeaeeaeeeaeeeaeeeaeeeas 8 9 8 5 2 Troubleshootings4 si cd se is Sse ne aed dd Aa TA A TEAR A 8 9 INDEX Index 1 to Index 2 About Manuals The following manuals are also related to this product In necessary order them by quoting the details
49. end 8 TROUBLESHOOTING This chapter describes the troubleshooting of the gateway functions 8 1 Troubleshooting Common to Gateway Functions The following troubleshooting is common to the gateway functions Definition and Cause The mounting position of the serial Phenomenon The GOT displays the Check Communication message communication board is incorrect The version of the ROM_BIOS OS installed in the GOT is incorrect The ERR LED is lit on the PLC x1 The used A9GT J71E71 T is not compatible with the gateway functions The used A9GT J71E71 T is not compatible with the gateway functions The extended function OS of the gateway functions has not been installed in the GOT When all bits of The memory board has not been mounted When A985GOT A97 x GOT A960GOT or A956WGOT is used not used When A956GOT is used The IP address has not been set to the GOT The mounting position of the bus connection board is incorrect The memory extension type M3 type GOT is Corrective Action Mount the serial communication board on the GOT lt gt User s Manual of used GOT Match the versions of the OSs to be installed All versions of the basic function OS PLC communication driver and extended function OS should be Ver 9 or later gt GT Designer2 Versioni Reference Manual Use the A9GT J71E71 T hardware version E June 2002 or later that is compatible with the
50. er2 has been made or not lt _3 Section 5 3 Use the A9GT J71E71 T that is compatible with the gatewa The used A9GT J71E71 T is not compatible with p SENAY the gateway functions L Section 2 3 0x010F4030 In the server setting of GT Designer2 check whether device been assigned to the accessed gateway device assignment is correct or the set device exists 0x010F4031 In the server setting of GT Designer2 check whether the device been assigned to the accessed gateway device within the monitor range has been assigned 1 Check for cable disconnection and check the communication board communication module mounting status and PLC status 2 This error may occur if the PLC load increases at other station access At that time move the other station data to the host Communication time out occurred PLC and monitor them on the host Module or cable is not loaded properly 3 If the sequence scan is long insert the COM instruction 4 Check the GOT error codes of the alarm list display function system alarm and system information If an error has occurred take the corresponding corrective action 1 0x 010F4B00 1 About the GOT error codes Refer to the following manuals for details of the GOT error codes gt A985GOT A975GOT A970GOT A960GOT User s Manual e A950GOT A951GOT A953GOT A956GOT User s Manual 8 3 2 Troubleshooting The following table indicates the troubleshooting for use of the server and client functions
51. ete files for screen copy For motion monitor data storage for screen copy For servo amplifier monitor data storage C for screen copy In addition to the above do not delete the file whose extension is ini GOT information file 6 3 3 Checking the line connection condition The connection condition of the line between the GOT and FTP client is stored into the GOT special register GS200 b2 bit position 2 By referring to this bit on the GOT you can check whether the line is connecting or not Device Name OFF GS200 b2 Connecting Cutt Refer to the following manual for details of the GOT special registers L gt GT Designer2 Versioni Reference Manual Example of using GS200 b2 1 Using the above device with the lamp display function you can create a line condition confirmation lamp GS200 b2 OFF GS200 b2 ON G Hint Line Connecting gt gt om pia 2 By setting the above device to the operation condition as a trigger using the touch key function or numerical input function you can restrict operation input while the line is connecting GS200 b2 OFF GS200 b2 ON Manufacturing line Using the touch key function or numerical input function make setting to enable input only when the device GS200 b2 is OFF 6 3 4 Line cutoff There are two line cutoff methods
52. ever function GOT server function Server setting Mitsubishi PLC Omron PLC a Setting items of the GOT client function e Script function s s s Make setting to write the internal device value of the GOT client function to the gateway device of the GOT server function e Client setting cece Register the GOT of the server function where the value will be written e Numerical input 1 function Make setting to input a value to the device of the Mitsubishi Electric PLC e Numerical input 2 function Make setting to input a value to the internal device of the GOT client function Z Setting item of the GOT server function e Server setting Make setting to assign the device of the Omron PLC to the gateway device Point About details of the script function Refer to the following manual for details of the script function lt gt GT Designer2 Versioni Reference Manual For the examples using the script function refer to Section 5 4 of this manual 5 1 4 PLC devices that can be assigned PLC devices that can be assigned The PLC PCU devices that can be monitored by the GOT and the GOT internal devices can be assigned to the gateway devices Refer to the following manual for the devices that can be monitored by the GOT lt gt GT Designer2 Versioni Reference Manual Precau
53. gateway functions gt Section 2 3 Use the A9GT J71E71 T hardware version E June 2002 or later that is compatible with the gateway functions gt Section 2 3 Install the extended function OS of the gateway functions into the GOT lt gt GT Designer2 Versioni Reference Manual Mount the memory board to the GOT Use the memory extension type M3 type GOT Using the utility function of the GOT check whether the IP address has not been set to the GOT Mount the bus connection board on the A9GT J71E71 T gt Section 2 4 Refer to the troubleshooting of the function corresponding to the ON bit and take a corrective action lt gt Section 8 2 1 1401 SP UNIT DOWN is displayed in the PLC diagnostics of GX Developer 2 Refer to the following for details of the gateway common information GS200 a a Section 8 2 Gateway Information x3 Check whether response is made to Ping or not by issuing the Ping command to the GOT from the personal computer Example ping IP address of GOT in Command Prompt GS200 are OFF and no response The is made to Ping gateway 2 3 functions are not executed When any of the GS200 bits is ON and response is made to Ping 2 3 8 1 8 2 Gateway Information The error information of the gateway functions is stored into the GOT special registers GS By monitoring the following GOT special registers you can confirm the error informati
54. hat meet the condition wild card When specifying multiple files you can use or as a wild card Example When specifying only JPEG fileS ecccceeeeeeseeeeeeeeeeteeeeaeeeeeeeeeaees jpg When specifying the CSV files that begin with Main 0 eee Main csv When specifying the files whose extensions begin with b b Point 1 Precautions for specifying the file name For the FTP server function do not put a space into a file name or extension The file that has a space cannot be read or written as a correct file name 2 About data in PC card The PC card of the GOT contains the files that can cause the operation fault of the GOT if they are deleted To prevent the operation fault of the GOT do not access the folders which store the above files from the FTP client lt Folder structure in the PC card gt _ ALARMHST gt For alarm history file storage Can be used with RECIPE For recipe file storage the FTP server lt REPORT gt For report file storage function SNAPSHOT gt For screen image file storage LSNAPHDCP BMP Work file for printer printout Cannotbe sed USERDATA For monitor screen data storage for screen copy OS eniai eiea For OS storage for OS copy with the FTP SYSTEMD 6e For OS system screen storage for OS copy server function SPCDATA eee For special function module monitor data storage Do not del
55. her of the following operations is performed the Gateway client dialog box is displayed e Choose the Common gt Gateway gt Client menu e Double click Gateway Client in the workspace b Gateway client dialog box 10 97 142 10 97 143 Item Description Set the N W numbers PLC numbers types etc of the GOTs of the server function to be monitored by the function GOT li Server function GOT list SOT of the client function N W No Register the network No of the corresponding GOT PLC No Register the PLC No station number of the corresponding GOT Type Fixed to GOT IP address Register the IP address of the corresponding GOT Port No Fixed to 5011 Communication Fixed to UDP OK Used to confirm the settings and close the dialog box Cancel Used to cancel the settings and close the dialog box Add Used to add a new GOT of the server function Click this switch to add the GOT of the server function and make settings Delete After selecting the settings click this switch to delete the settings Delete All Used to delete all settings Copy After selecting the settings click this switch to copy the settings 5 4 Examples of Use The following gives the examples of using the sever and client functions Making access to the PLC from the personal computer via the GOT The device values of EGO to EG5 of the GOT 1 server function are displayed on MX Component EG devices EGO to EG5 of GOT 1 are mon
56. ilable FTP client tool or like refer to the manual of the FTP client tool used General procedure Start Vv Connect the line of the GOT and FTP client perie Refer to Read the file of the GOT PC card poce Refer to Write a file to the GOT PC card peee Refer to y Operate the directory of the GOT PC card ErREHS Refer to 6 Cut off the line of the GOT and FTP client Refer to End Point P Precautions for file write When writing a file to the GOT PC card or operating the directory turn ON the memory card access switch of the GOT to make the PC card write enabled System configuration TAT FTP client File read File write Directory operation FTP server IP address i PC card 10 97 14 200 a Connecting the line of the GOT and FTP client Connect the GOT and FTP client in the following procedure Star of the FTP Client osc c5 cte See eens ftp Connection with the GOT s ssssnssnssssnsinrisrnsnsrnrisrnrnsrssnnrnnenns open IP address of GOT 2 Input of the login Name aasssessssesssrressrrresrrrnessnnnesrnnnesnnnesnnnnennnn login name 4 Input Of the password sssssssisssssssssrnrrensssetrrnnnnnsstnrnnnnnnnsn ene password Login image when the line was connected properly
57. in the tables below Related Manuals Manual Name GT Designer2 Version1 Operating Manual Describes methods of operating GT Designer2 and transmitting data to GOT Option GT Designer2 Version1 Reference Manual Describes the specifications and settings of each object function used in GT Designer2 Option GOT A900 Series Operating Manual GT Works2 Version1 GT Designer2 Versioni compatible Extended Option Functions Manual Describes the following extended functions and optional functions applicable to GOT e Ladder monitor e Network monitor e Servo amplifier monitor Utility Special module monitor Module monitor e Font change e System monitor List editing CNC monitor Option GOT A900 Series User s Manual GT Works2 Version1 GT Designer2 Version1 compatible Connection System Manual Describes the system configuration of which connection method is compatible with GOT A900 series as well as processing cables Option A985GOT A975GOT A970GOT A960GOT User s Manual Explains the performance specifications installation methods communication board communication unit mounting methods and others of the GOTs Option A950GOT A951 GOT A953GOT A956GOT User s Manual Explains the performance specifications installation methods communication board communication unit mounting methods and others of the GOTs Option MX Component Version3 Operating Manual Explains the setting and operating methods of the utilities on MX Com
58. ion Since the GOT cannot receive mail set FROM as the mail address of the personal computer or like on the production site This allows the mail to be returned from the office manager to the production site and the mail requesting confirmation of the restoration condition to be sent to the production site 1 GOT setting example a Utility menu of GOT Item Description IP address 10 97 14 1 Send message wait 000 x 10ms Send message time 03 seconds Startup time 003 seconds b Mail setting Item Description SMTP mail server 10 97 14 12 FROM Mail address of personal computer 1 TO Mail address of personal computer 1 cc Mail address of personal computer 2 Mail address of Cellular phone subject GOT01 c Alarm history display function alarm history common setting Description Monitor device Mail send Send mail Occurred restored Preset the comment to be displayed for the alarm history display function 7 5 Precautions The precautions for using the mail send function are described below 1 The languages that can be sent by mail is only English The other languages are sent as by mail 2 The GOT refers to the PLC CPU clock every 60 minutes Note that if the time is changed on the PLC side an error of up to 60 minutes will be produced 3 The mail send date time is the time of the SMTP server at the time of s
59. ion x1 If six or more clients GOT personal computer make simultaneous access to the servers GOTs the scripts of the clients may stop 5 2 2 Access range that can be monitored The access range of the server and client functions is shown below When the PLC CPU is monitored via the GOT only the PLC CPU device set to the gateway device of the GOT can be accessed e The device of the PLC CPU as the network destination can be monitored when it is assigned to the gateway device of the GOT connected e The GOT cannot monitor the PLC CPU of Ethernet connection Ethernet PLC 1 GOT 1 Bus connection RS 232C RS 422 communication GOT 2 Bus connection RS 232C RS 422 communication Personal computer MX Component Monitor Destination Personal GOT 1 GOT 2 PLC 1 PLC 2 PLC 3 PLC 4 PLC 5 computer Server Server Monitor Source Fis e or PE cramer pee ae e ee Pe 2r eee Cees eso Eos ee 5 ee ee Can monitor the gateway device
60. ion RS 422 communication RS 422 communication l Be oF T Company A PLC Micro computer board 2 SYSTEM CONFIGURATION This chapter describes the system configuration of the gateway functions 2 1 System Configuration of Gateway Functions 2 When the gateway functions are used one GOT connects to Ethernet and PLCs and therefore both the Ethernet communication module and communication board must be mounted to the GOT Hence the gateway functions cannot be used for the GOT that cannot be mounted with the Ethernet communication module and for the connection form that uses the communication module Example 1 For A951GOT Example 2 For CC Link connection Since the Ethernet communication module cannot be Since two different communication modules cannot be mounted the gateway functions cannot be used mounted to one GOT the gateway functions cannot be used lt k R s CC Link Xe communication module A951GOT Ethernet GOT communication module Ethernet communication module 2 2 Connection Form The GOTs that can use the gateway functions are indicated on a connection form basis Refer to the following manual for details of the connection forms lt gt GOT A900 Series User s Manual GT Works2 Version1 GT Designer2 Version1 compatible Connection System Manual Usable Xx Unusable Notconnectable A950 oT A970 A956W A956QOT ee GT Bus connection CPU direct connec
61. itored MX Component lt EG0 150 EG1 480 EG2 230 EG3 370 EG4 80 EGS 25 Device batch read function is issued to GOT to monitor EGO to EG5 devices of GOT Ethernet 7 PLC devices D10 to D15 GOT utility menu ORS are monitored GOT NET No H D10 150 D11 480 GOT PC No 2 GOT 1 D12 230 D13 370 GOT IP address 10 97 14 2 L D14 80 D15 25 GT Designer2 Gateway server setting Bus connection EG device Device Points RS 422 communication EGO 0 FF D10 6 RS 232C communication PLC device values D10 150 D11 480 D12 230 D13 370 D14 80 D15 25 PLC e Tabea E rE 1 GOT 1 setting example a Server setting EG Device Points EG 0 FF D10 Word b Numerical display function Description Device D10 to D15 Network 2 Personal computer setting Set the personal computer in the environment where Ethernet can be used 5 13 5 13 Displaying on the client GOT the alarms that occurred on multiple PLCs The device values of the PLC 2 and PLC 3 are transferred to the internal devices GD100 to GD147 of the GOT 1 The GOT 1 monitors its own internal devices and if an alarm occurs on the PLC 2 or PLC 3 displays the occurrence information GT Designer2 clie
62. k Performance of server and client functions reference values The following table indicates the performance of the server and client functions reference values when and on the previous pages are used The reference values of the performance assume the following conditions e System consists of one GOT of server function and one GOT of client function e GOT of server function Numerical input setting of 64 points e GOT of client function Numerical input setting of 64 points e Number of assigned device points Word devices of 10 points eee bmov is used Response speed for bus Response speed for Batch access together connection CPU direct connection 1 Approx t4oms Approx 260ms 2 oF Approx 700ms Approx 1300ms s doo x prox 700ms_ Approx 1300ms 4 Approx 1300ms When there are multiple clients the response speed is the above response speedxnumber of clients When there are five clients in above 1 the response speed for bus connection is approximately 700ms 6 FIP SERVER FUNCTION This chapter descries the FTP server function 6 1 Specifications The specifications of the FTP server function are indicated below Item Specifications Setting Method FTP server function setting Whether the function will be used or not can be set default Not used GT Designer2 1 to 12 alphanumeric characters case sensitivity anonymous must not User name GT Designer2 be used defaul
63. l to Ethernet Fit the communication board to the GOT or Ethernet communication module and connect it with the PLC by the cable For QnA ACPU bus connection make setting with the extension number and I O slot switches on the communication board l To next page Section 2 4 in this manual Connection System Manual Ce ee KH Ee Fit the Ethernet communication module to the GOT and connect the User s manual of the used Ethernet cable GOT From previous page Set the gateway functions to be used When using the server and client functions Make server and client settings on GT Designer2 When using the FTP server function Create monitor Make FTP server setting on GT Designer2 screen data When using the mail send function Set the mail of each object on GT Designer2 Set the send destination and SMTP server in the mail send setting Create monitor screen data Download the i Transfer the monitor screen data to the GOTs monitor screen Transfer by RS 232C communication or transfer using the PC cards data Debug End Sections 5 3 6 2 7 2 in this manual GT Designer2 Version1 Reference Manual GT Designer2 Version1 Operating Manual 4 FUNCTION SETTING To use the gateway functions settings related to the gateway functions must be made on both the GOT and GT Designer2 Settings to be made on the GOT and GT Designer2 will be described below Server a
64. n Transfers the data of 32 points starting from EGO of GOT 2 to GD100 and later of GOT 1 Script 1 e Script function for GOT 3 alarm display Item Description Type Screen script Trigger type Sampling 5 sec Unsigned BIN 16 bit bmov 1 3 w EGO w GD132 16 Script description Transfers the data of 16 points starting from EGO of GOT 3 to GD132 and later of GOT 1 Script 2 2 GOT 2 setting example a Server setting Points O FF _ 1B200 es 512 EG Device 3 GOT 3 setting example a Server setting EG Device Points Point P About the trigger type When using the script function do not set the trigger type as Ordinary or Sampling within 2 seconds Doing so may affect the other monitor operations 5 15 5 15 Monitoring and controlling the production conditions of multiple PLCs with the server GOT The device values of the PLC 2 and PLC 3 are transferred to the EG devices of the GOT 1 devices of the PLC 1 When values are written to the PLC 1 the EG devices of the GOT 1 internal devices GB100 GB101 of the GOT 1 turn ON Check completion of write using the lamp display function or like The GOT 1 monitors the devices of the PLC 1 to check the production conditions of the PLC 2 and PLC 3 PLC 1 devices D100 233 D101 EG0 b0 OFF gt ON EG0 b1 OFF ON EG2 233 EG3 523 523 EG0 b0 EG1 b1 turn
65. nd client functions lt System configuration example gt e Utility menu of the GOT Refer to Section 4 1 Set the network No station number IP address MX Component etc of the GOT itself on each GOT IP address 10 97 14 20 001 1239 4 GOT PC No 01 164 GOT IP ADDRESS 000 000 000 000 GOT PORT No 05001 102465534 ROUTER ADDRESS 000 000 000 000 SUBNET MASK 255 255 255 000 SEND MESSAGE WAIT 000 x10ms 0300 IP SEND MESSAGE TIME 03 sec 3 90 7 START UP TIME 0 0 3 sec o ess 10 97 14 254 Page 272 T SELECT CHANGE ao E E Ethernet GOTNWNo 1 GOT PC No 2 GOT IP address 10 97 14 11 Router address 10 97 14 254 GOTNWNo 1 GOT PC No 1 GOT IP address 10 97 14 10 Router address 10 97 14 254 E IP e GT Designer2 Refer to Section 5 3 10 97 15 254 lt Server setting gt Setting of the server function to the GOT Assign the PLC CPU devices to the gateway devices to be accessed by MX Component and E the GOT of the client function GOTNWNo 2 GOT PC No 4 GOT IP address 10 97 15 10 Router address 10 97 15 254 Em Delete All ex lt Client setting gt Setting of the client function to the GOT Register its the network No PLC No and IP addresses of the GOTs of the server function to be accesse
66. nsibility of Mitsubishi loss in opportunity lost profits incurred to the user by Failures of Mitsubishi products special damages and secondary damages whether foreseeable or not compensation for accidents and compensation for damages to products other than Mitsubishi products replacement by the user maintenance of on site equipment start up test run and other tasks 5 Changes in product specifications The specifications given in the catalogs manuals or technical documents are subject to change without prior notice 6 Product application 1 In using the Mitsubishi MELSEC programmable logic controller the usage conditions shall be that the application will not lead to a major accident even if any problem or fault should occur in the programmable logic controller device and that backup and fail safe functions are systematically provided outside of the device for any problem or fault 2 The Mitsubishi programmable logic controller has been designed and manufactured for applications in general industries etc Thus applications in which the public could be affected such as in nuclear power plants and other power plants operated by respective power companies and applications in which a special quality assurance system is required such as for Railway companies or Public service purposes shall be excluded from the programmable logic controller applications In addition applications in which human life or property that could be greatly affe
67. nt setting IP Address 1 2 10 97 14 2 1 3 10 97 14 3 GOT utility menu GOT NET No 1 GOT PC No 1 IP address 10 97 14 1 GOT internal devices I 4 GD100 to 131 GD132 to 147 Transferred by script 2 Transferred by script 1 5 second sampling 5 second sampling Ethernet H GOT utility menu GOT NET No 1 GOT utility menu GOT NET No 1 GOT PC No 3 IP address 10 97 14 3 GOT PC No 2 IP address 10 97 14 2 GT Designer2 server setting EG device Device Points EGO 0 FF 300 256 GT Designer2 server setting EG device Device Points EGO 0 FF IB200 512 oo Moj PLC 2 1 GOT 1 setting example a Client setting IP Address 10 97 14 2 10 97 14 3 b Alarm list display function for GOT 2 alarm display Description Number of device points 512 points consecutive Device GD100 b0 c Alarm list display function for GOT 3 alarm display Description Number of device points 256 points consecutive GD132 b0 Preset the comments that will be displayed by the alarm list display functions 5 14 5 14 d Script function for GOT 2 alarm display Item Description Type Screen script Trigger type Sampling 5 sec Unsigned BIN 16 bit bmov 1 2 w EG0 w GD100 32 Script descriptio
68. of the client function accesses the host devices of the GOT of the server function access can be made with the program that reads 50 points starting from EGO 1 Script description example EG Device Layout 1 bmov W GD100 1 2 w EGO0 50 2 Devices of host other station and other PLC are set not together When the GOT of the client function accesses the host devices of the GOT of the server function access requires the program that reads 40 points starting from EGO 1 and the program that reads 10 points starting from EG130 2 Script description example SEE eee 1 bmov W GD100 1 2 w EGO 40 EGDevice Type PLC Device Ponts 2 bmov w GD140 1 2 w EG130 10 wT pae Delete All i if A Hint To further increase efficiency By reserving together in advance the PLC devices to be used for the server and client functions in the system design stage as shown in the following a the number of times for the GOT of the server function to access the PLC can be decreased improving the processing speed a When PLC devices are assigned together When 100 points of a le devices are accessed access to the PLC occurs Delete only once Delete All b When PLC devices are not assigned together So xi When 100 points of EG Denes Layout devices are accessed access to the PLC must Delet i sls be made five times Delete All Chec
69. on of the gateway functions Refer to the following manual for details of the GOT special registers lt GT Designer2 Versioni Reference Manual Error information list of gateway functions 1 GOT write information Device Description GS200 Gateway common information Refer to a on the next page GS201 Error counter Stores the number of error occurrences GS202 Error code Stores the error code refer to Section 8 4 1 GS203 Stores the year upper byte 2 lower digits of year and month lower byte of the error occurrence date and time in BCD code Occurrence date Stores the day upper byte and hour lower byte of the error occurrence date and time in BCD code Stores the minute upper byte and second lower byte of the error occurrence date and Mail send GS204 function G5203 time in BCD code GS206 to 209 GS210 Error counter Stores the number of error occurrences GS211 Error code Stores the error code refer to Section 8 2 1 Stores the year upper byte 2 lower digits of year and month lower byte of the error GS212 ries occurrence date and time in BCD code Occurrence date Stores the day upper byte and hour lower byte of the error occurrence date and time GS213 4 and time in BCD code Stores the minute upper byte and second lower byte of the error occurrence date and GS214 Piet time in BCD code GS215 Stores the lower part of the IP address of the GOT client function where the er
70. ood Bye Ci gt a Error display An error that occurred in the FTP server function is displayed on the FTP client Refer to the following for the displayed error messages L3 Section 8 2 Error Messages If an attempt was made to read an non existing file snap0010 bmp 6 11 fto gt get snap0010 bmp 200 PORT command successful 550 snap0010 bmp No such file or directory Ci gt 6 5 Precautions The following are the precautions for using the FTP server function Precautions for system design using the FTP server function 1 When writing a recipe file from the FTP client to the GOT set the format of the recipe file as set for the recipe function of the GOT When writing a recipe file from a remote location confirm the operation with the field site personnel before executing write S Before using the FTP client tool refer to the manual of the FTP client tool confirm its functions and operation methods and make tests before starting operation Depending on the FTP client tool used the GOT FTP server may not support some operations Also depending on the FTP client tool used the FTP server function may not be usable since the GOT cannot support the extended command quote and issue the GOT dedicated command 3 If a number of files are read at once under one command e g get or put is executed by specifying a wild card processing may be delayed by network congestion If processing is slow issue commands
71. or mounting the Communication board cccceeceeseeteeseeteees 2 2 R Required devices 2 00 eeeeeeeeeeeeeeeeeeeeeeeeeateees 2 2 S Server setting seat ec es Aedes 5 10 Setting method FTP Server fUnCtiOn ccccccccssecessseeeeessees 6 3 Mail Send function cccceeesseeeeteeeeeeeees 7 3 Server and client functions cee 5 10 Specifications FTP Server fUNCtiONn c ccccccssceessseeeesaes 6 1 Mail Send function ccccccceesseeesseeeeeeees 7 1 Server and client functions cceeeee 5 8 System configuration cceceeeeeeeeeeeeees 2 1 System configuration of gateway functions 2 1 T Troubleshooting FTP server fUnCtiOn c ccccccsseeeesseeeessees 8 8 Mail Send function ccccceeesseeesteeeeeeees 8 9 Server and client functions seeeee 8 6 W What is gateway device eeeeeeeeeeeeeteeees 5 1 When using the bus connection board 2 3 When using the serial communication board 2 2 Index 1 MEMO Index 2 Index 2 WARRANTY Please confirm the following product warranty details before using this product 1 Gratis Warranty Term and Gratis Warranty Range If any faults or defects hereinafter Failure found to be the responsibility of Mitsubishi occurs during use of the product within the gratis warranty term the product shall be repaired at no cost via the sales representative or Mitsubishi Service Company
72. ory detail comment nothing appears under Detail Information To display Detail Information make the detail display setting in the comment window 2 Example of display at destination when an alarm recovered Alarm history repaired information repair Time 2002 11 28 10 38 23 repair Information Alarm Line A supply conveyor stopped recovered Alarmhistory detail comment nothing 7 4 Examples of Use Sending the definition of the alarm that occurred in the GOT to the production site and office by mail If an alarm has occurred in the GOT mail is sent to the personal computer 1 production site operator cellular phone and personal computer 2 office manager On the production site where the alarm was received the system is repaired recovered At the office the manager can send mail to prompt the operator on the production site to report the current restoration condition Mail is sent SMTP mail server m M 10 97 14 12 a z ea i Mail is sent Personal computer 2 Office manager Coren i208 Cellular phone Ethernet Mail is sent Mail is sent M1 H GOT 10 97 14 1 Personal computer 1 mr Production site operator a Ho Jg A sesali el PLC M Mail is returned Operator is asked to check restoration condit
73. ot used the default value is used for operation SEND MESSAGE Set the send message wait to reduce the loads WAIT of the network and target PLC SEND MESSAGE h ime TIME OE E E START UP TIME Set when to start communication in seconds after power on of the GOT x1 Set the IP address after consulting the network manager person who does network planning IP address management etc x 2 Before setting the values have them checked by the network manager 3 When sending multiple mails set the time interval from when one mail is sent until the next mail is sent 4 The send message time for connection with the SMTP server at the start of mail sending has been set to 1 minute fixed Set the send message time after connection of the SMTP server 4 2 GT Designer2 Setting Set the gateway functions in the gateway setting of GT Designer2 For the settings refer to the setting methods of the corresponding functions When using the server and client functions L gt Section 5 3 Setting Method When using the FTP server function lt gt Section 6 2 Setting Method When using the mail send function gt Section 7 2 Setting Method 5 SERVER AND CLIENT FUNCTIONS This chapter explains the server and client functions 5 1 Gateway Devices 5 1 1 What are the gateway devices The gateway devices are virtual devices designed exclusively to perform the server and client functions on the GOT and the PLC CPU device
74. ponent Option MX Component Version3 Programming Manual Explains the programming procedures detailed descriptions and error codes of the ACT controls Option Manual Number Model Code SH 080278E 1DM205 SH 080251 1DM204 SH 080253 1DM206 SH 080255 1DM207 SH 4005 1DM099 SH 080018 1DM103 SH 080271 13JU32 SH 080272 13JF66 About the Generic Terms and Abbreviations The following abbreviations and generic terms are used in this manual E GOT Generic Term Abbreviation A985GOT V A985GOT TBA V A985GOT TBA A975GOT TBA B A975GOT TBA EU A970GOT TBA B A970GOT SBA A970GOT TBA EU A975GOT A960GOT EBA A956WGOT TBD A956GOT TBD A956GOT TBD M3 A953GOT TBD A953GOT TBD M3 A951GOT TBD A951GOT TBD M3 A951GOT QTBD GoT agoo A956GOT Series A950GOT TBD A950GOT TBD M3 A95 h T andy GOT A953GOT LBD M3 H AQ56GOT AQ50GOT Z z g lg z 2BBl 3 18k ol oi ol ol oOo ala IN N N x oO gt de QO x Q o o Q 6 8 18 ea Sell 6 6 18 Q 4 4 4 4 g 30 4 4 A O 4 m E Communication board Communication module Generic Term Abbreviation vec ty Bus connection board A9GT QBUSS Communication board Serial communication A9GT RS4 board A9GT 50WRS4 Communication Ethernet eer A9GT J71E71 T module communication module Option unit Generic Term Abbreviation Memory card i A1SD59J MIF interface module Option module Description A985GOT TB
75. rd basis 4 The network number and PLC station number must be set to assign the MELSEC A QnA Q series PLC CPU devices 5 The CPU number must be set to assign the CPU of the multiple PLC system 6 If station No is changed while monitoring the gateway device to which PLC CPU device has been assigned the monitored device is irrelevant to the station No change Example When station No is changed on the GOT server Use the script function to read EGO to the GOT internal device Ethernet LI L Station No is changed Station number switching device GOT internal devices Gateway device GD100 250 EGO OOFF gt 0101 GD100 D1 Assignment i definition 2 50 EG0 D100 GOT Client function GOT Server function Station No 0 OOFF Monitoring Station No 1 s n Station No 1 3 z 0101 Station No 2 If station No is changed on the GOT server As D100 has not been assigned to the gateway device the station No change is irrelevant to the on the GOT server station No change is executed GOT client
76. ror occurred in BIN code Request source r Stores the upper part of the IP address of the GOT client function where the error GS216 occurred in BIN code GS217 to GS219 GS220 Error counter Stores the number of error occurrences GS221 Stores the error code refer to Section 8 2 1 Stores the year upper byte 2 lower digits of year and month lower byte of the error GS222 x Se occurrence date and time in BCD code Occurrence date Stores the day upper byte and hour lower byte of the error occurrence date and time GS223 and time in BCD code Stores the minute upper byte and second lower byte of the error occurrence date and GS224 ee time in BCD code GS225 Stores the lower part of the IP address of the GOT server function where the error occurred in BIN code Request source 7 Stores the upper part of the IP address of the GOT server function where the error GS226 y occurred in BIN code GS227 to GS229 z 2 GOT read information Device Description GS400 Gateway common control Refer to b given below a Gateway common information GS200 fois b14 bistobi2 oni bioos b be ot vo bO ON while the mail send function is ready b1 ON while the FTP server function is ready b2 Turns ON when the FTP client logs in b3 ON while the server function is ready b4 ON while the client function is ready b5tob10 Reserved b11 Turns ON when an error occurs in the mail send function b12
77. s and GOT s internal devices are assigned to the gateway devices for use When accessing the PLC from the personal computer via the GOT E 5 Accessing the gateway devices of the GOTs server function from the personal computer enables indirect access to the PLC CPU devices Use MX Component Personal computer Version 3 or later Mitsubishi PLC l D100 250 N Omron PLC ll rnc 3 Access to gateway devices C Ethernet M Gateway device Gateway device EGO EGO e Assignment Assignment definition definition EG0 D100 EG0 TIM50 f GOT server function f GOT server function D100 250 Omron PLC Mitsubishi PLC Refer to the following for the devices required for the GOT LF Section 2 3 Required Devices When monitoring the PLC of different maker from one GOT Accessing the gateway device of the GOT server function from the GOT client function enables indirect access to the PLC CPU device Access to gateway device Mitsubishi PLC Gateway device D100 250 ree 7 Assignmen oe Omron RES definition TIMSO EGO TIM50 GOT client function GOT server function Access to PLC D100
78. separately to perform the processing separately Precautions for file read 1 The GOT cuts off the line if no command is input from the FTP client for longer than the time set to the watching timer of command input 2 The line is cut off if any of the GOT IP address router address and subnet mask is changed while the line of the GOT and FTP client is connecting 3 The line is kept connected if the GOT is put offline e g the monitor screen data is downloaded while the line of the GOT and FTP client is connecting 4 When you want to change rewrite the contents of the recipe file make the recipe inactive If the recipe file in the PC card is deleted during recipe processing the function will not operate properly If the recipe file is deleted other than during recipe processing an error system alarm recipe file error will occur in the next recipe operation CF Section 6 3 3 Checking the line connection condition o aS Do not delete the printer printout temporary file If the printer printout temporary file is deleted the function will not operate properly O aS If the FTP client has become faulty personal computer wait until the time set to the watching timer of command input elapses or turn ON the forced logout signal GS400 b2 to cut off the line and log in again The line connecting condition can be checked using GS200 b2 bit position 2 7 Do not power off the GOT while access is being made from
79. t GOT900 9 Password 1 to 8 alphanumeric characters case sensitivity default GOT900 GT Designer2 Port number 20 21 Fixed Number of clients that can connect j 1 unit Fixed simultaneously Time set to i i i oe en a watching timer of command input After login 1 to 60 minutes default 15 minutes GT Designer2 File size that can be read Unlimited max read size depends on PC card capacity Within 8 characters of only alphanumeric characters File name longer file name not acceptable anes Normal Reference mode write to PC card disabled Write is enabled after issue of dedicated command p e General purpose FTP client tool can be used FTP client e Access can be made by FTP command from Windows MS DOS prompt or command prompt Memory space used by GOT bytes 12 2 x total number of login name and password characters GT Designer2 1 The line is cut off if a correct password and login name are not entered within 1 minute after line connection with the GOT 2 The GOT cuts off the line if a command is not input from the FTP client within the time set to the watching timer of command input 3 Microsoft Internet Explorer and Netscape Communicator are unusable The following table indicates the FTP client tools that have been confirmed to operate properly by Mitsubishi Electric Name Compatible OS Microsoft Windows 98 operating system Microsoft Windows Millennium Edition operating
80. that monitors D100 assigned to the gateway device 5 18 5 18 Precautions for setting the script function 1 When setting the script function do not set the trigger type to Ordinary or Sampling within 2 seconds Doing so may affect the other monitor operations 2 The script function cannot be used to monitor the gateway devices of the GOT itself When monitoring the PLC devices assigned to the gateway devices monitor the PLC devices directly Precautions for using GT Simulator for debugging 1 GT Simulator cannot debug the gateway functions An error will occur if the gateway device is monitored or data is written to the gateway device Precautions for monitoring 1 If the GOT monitors devices by transient communication via the network the monitor speed 5 19 will decrease To increase the monitor speed use link devices If the gateway device of the GOT of the server function is monitored in a status where the server and client functions cannot be used an error occurs and the script stops x While power is off when the ROM_BIOS version of the GOT is incompatible or when the memory board is not fitted for example The gateway device to which the PLC device has not been assigned is monitored as 0 OFF for bit When write is executed the written value is invalid If the screen save of the GOT is canceled by a screen touch or the human sensor during execution of the script that uses the gateway
81. the PLCs and system GOTs configuration e PLC setting device assignment etc e GOT setting IP address network number station number etc Connect the GOTs and the personal computer where GT Designer2 has GT Designer2 Version1 started by the RS 232C cable Operating Manual Fit the memory boardstotheGOTs ee User s manual of the used Not required when the A956GOT is used GOT v Check the ROM_BIOS versions of the GOTs sea GT Designer2 Version1 If the ROM_BIOS version does not support the gateway functions install 4 5 di 2 y Operating Manual Install the OSs ROM_BIOS again into the GOTs l Install the system programs into the GOTs e Basic function OS e PLC communication driver Extended function OS gateway functions and other necessary ead GT Designer2 Version1 Operating Manual OS When the GOT is restarted the utility menu appears Select Memory Extended Option information to check whether the installed OSs are correct or not Functions Manual Set the following items in the utility setup of the GOT IP address of the GOT Set the NET No network number and PLC No station number of the GOT e When making bus connection with the QCPU set the extension number and I O slots e When making other connection make communication settings Connect the GOTs such as the transmission speed to the PLC as required Section 4 1 in this manual Connection System Manua
82. timed out request timed out request timed out C 6 2 Setting Method Operation procedure When either of the following operations is performed the FTP dialog box is displayed e Choose the Common gt Gateway FTP menu e Double click FTP in the workspace FTP dialog box Item Use FTP Server Login Name Password Watching timer of command input FTP Ea lV Use FTP Function Login Name E 07900 Password GoTs00 Watching timer of command input 15 Min Cancel Description Check here when using the FTP server function Set the login name used when the FTP client connects to the GOT You can set only one login name up to 12 characters Only alphanumeric characters a to z A to Z 0 to 9 can be used Set the password used when the FTP client connects to the GOT You can set only one password up to 8 characters Only alphanumeric characters a to z A to Z 0 to 9 can be used Set when the line with the GOT will be cut off if no command is entered from the FTP client You can set this time between 1 and 60 minutes in 1 minute increments Normally use it as default 15 minutes 6 3 Operation on the FTP Client Side 6 3 1 Input command at FTP client append ascii binary bye cd close delete dir get Is mdelete mdir mget mkdir mis mput open put pwd quit quote user Com Function Reference Name ee les General commands The following table indicates the
83. tion Computer link connection MELSECNET connection CC Link connection Ethernet connection Third party PLC connection Microcomputer connection x 1 When using the A956GOT use the memory extension type A956GOT TBD M3 A956GOT SBD M3 A956GOT LBD M3 GOT 2 Unable to make RS 232C RS 422 communication the A956GOT cannot be connected with the FXCPU or third party PLC 2 1 2 1 2 3 Required Devices The following devices of the GOTs are required to use the gateway functions A a Fo Application Required Device A97LIGOT A960GOT A956WGOT Connieats GOT 1 Ethernet communication module A9GT J71E71 T Hardware version E June 2002 or later 1 Ethernet system Bus connection QCPU Q mode Bus connection Connects GOT to Communication QnA ACPU A9GT QBUSS or A9GT QBUS2S 2 3 A9GT BUSS or A9GT BUS2S 2 3 PLC RS 232C A9GT RS2 or A9GT RS2T AQGT 50WRS2 communication Cannot be RS 422 connected A9GT RS4 A9GT 50WRS4 communication Executes t JENY Memory board A9GT QFNB 4 8M or A9GT FNB 1 2 4 8M Not required functions with GOT JEIDA Ver 4 2 compliant PCMCIA 2 1 compliant PC card 4 Required to use Flash PC card A9GTMEM 10MF A9GTMEM 20MF Gunes Wasa FTP server Soviet A9GTMEM 40MF function Cannot be Compact flash PC card Compact FlashTM compliant compact flash PC card x5 ead k 1 The gateway functions cannot be used with the hardware version D or earlier k2 The bus connection module
84. tions for monitoring the gateway devices When the following PLC CPU devices are assigned to the gateway devices they cannot be monitored depending on the used script function commands or MX Component functions The restricted commands functions are indicated on a PLC CPU basis No restrictions A Some devices cannot be used unusable device names are indicated in parentheses Restricted Script Function Commands Restricted MX Component Functions ReadDeviceRandom Maker Name bmov fmov Word device Bit device ReadDevice WriteDeviceRandom instruction specified specified Block Bit device specified specified Q QnA A FX CPU motion A A A Mitsubishi TT TC CT CC Z BM Electric TT TN CU CD Allen Bradley PL en Bradley RLE CN TP TA CP Omron PLC Sharp PLC Yaskawa PLC Toshiba PLC TD SS WDT Hitachi PLC MS TMR CU RCU CT R DIF DFN Matsushita Electric Works PLC O TT TN CU CD A CN TP TA CP O O O O TD SS WDT MS TMR CU O RCU CT R DIF SIEMENS PLC a a a a Example When the bmov instruction is used with the script function E The gateway device to which TT Allen Bradley PLC device has been assigned cannot be monitored x1 The devices not indicated in the above table can be monitored x2 Can be monitored if the bit device specified command is used Device TT is assigned to gateway device EG0 T4 0 14 TT GOT client fun
85. ulator2 GT Simulator2 screen simulator for GOT900 GT SoftGOT2 monitoring software MX Component ActiveX communication support tool E CPU Generic Term Abbreviation Description QOOJCPU QOOCPU Q01CPU Q02CPU QCPU Q Mode QO02HCPU QO6HCPU Q12HCPU Q25HCPU QCPU Q12PHCPU Q25PHCPU Q12PRHCPU Q25PRHCPU QCPU A Mode QO02CPU A Q02HCPU A QO6HCPU A Remote I O Network module for MELSECNET H network system remote I O station station QJ71LP25 25 QU72LP25 QJ72BR15 Q2ACPU Q2ACPU S1 Q2AHCPU Q2AHCPU S1 anacpu ONACPU type Q3ACPU Q4ACPU Q4ARCPU QnASCPU type Q2ASCPU Q2ASCPU S1 Q2ASHCPU Q2ASHCPU S1 AnUCPU A2UCPU A2UCPU S1 A3UCPU A4UCPU AnACPU A2ACPU A2ACPU S1 A3ACPU AnNCPU A1NCPU A2NCPU A2NCPU S1 A3NCPU AnCPU type AnUCPU AnACPU AnNCPU AnUS H CPU A2USCPU A2USCPU S1 A2USHCPU S1 ACPU AnS H CPU A1SCPU A1SCPUC24 R2 A2SCPU A2SCPU S1 A1SHCPU A2SHCPU A2SHCPU S1 A1SJ H CPU A1SJCPU A1SJCPU S3 A1SJHCPU AnSCPU type AnUS H CPU AnS H CPU A1SJ H CPU A1FXCPU A1FXCPU AOJ2HCPU A2CCPU A2CCPUC24 A2CJCPU FXo series FXon series FXos series FX series EXCPU FXin series FX nc series FXis series FX2 series FX2c series FXen series FXenc series FXen 10GM 20GM series FXsuc series Motion controller CPU Q series Q172CPU Q173CPU Motion controller A273UCPU A273UHCPU A273UHCPU S3 CPU Motion eoatrallor A373CPU A373UCPU A373UCPU S3 CPU A series A171SCPU A171SCPU S3 A171SCPU S3N A171SHCPU A171SHCPUN A172SHCPU A172SHCPU
86. wing table indicates the troubleshooting for use of the mail send function Phenomenon Mail is not sent Time of sent mail is incorrect Sentence of mail sent received by cellular phone is broken midway Definition and Cause The SMTP server does not operate properly FROM of the send source is not set correctly An attempt was made to send 17 or more mails at one time The time of the SMTP server is wrong The GOT sends mail at the time of the SMTP server The number of characters that can be sent received by the cellular phone was exceeded Corrective Action Ask the network manager if the SMTP server is operating properly Check whether FROM of the send source is set correctly Reduce the number of mails to be sent simultaneously to 16 or less Check whether the time of the SMTP server is precise or not Reduce the number of characters in the sentence sent by mail to within the number of characters that can be sent received by the corresponding cellular phone INDEX A About system programs sses 2 4 Access range FTP server function ccccccceeseeeesseeeeees 6 2 Mail send fUNCtiON cccceeeteeeeeseeeeees 7 2 Server and client functions cccceee 5 9 C Checking the line connection condition 6 6 Client setting ceceeeceeseeseceeseeeeeeeeeieeeeeeees 5 12 Connection FOF ccceceeccesseeseeesseeeseeeesseeeees 2 1 E Error codes and error messages
87. ye Pets TT C7 yi iy aq Eee 57 ELERTE a VA Li 5 YS 00K EEE Ce eZ seed 48 Le Mitsubishi PLC Company APLC Micro computer Mitsubishi PLC Company A PLC Micro computer board board Monitoring of other GOTs from client GOT server function client function Monitoring of the GOTs servers from the GOT client allows data to be read written indirectly from to the PLC CPU devices being monitored by the GOTs servers Use of the client function enables data to be read written indirectly from to the PLC CPUs of different makers that are different from the maker of the PLC CPU connected to the GOT client Ethernet RS 232C communication RS 232C communication Bus communication RS 422 communication RS 422 communication RS 232C communication RS 422 communication ses LU Mitsubishi PLC TH Gin gt Gp a am Be o ei MRO Sof af Company A PLC Micro computer board 1 2 Features of FTP Server Function Using the FTP server function you can read write data recipe alarm history screen image data saved in the PC cards of the GOTs from the personal computer General purpose FTP client tool Windows MS DOS prompt or command prompt Recipe data CSV file alarm history data CSV file or screen image data BMP JPG file are read to personal computer Recipe d

GOT-A900 Series Operating Manual (GT

Contents

Download Pdf Manuals

Related Search

Related Contents