INSTRUCTION MANUAL ScanSpeed 1730R
Contents
1. 10 5 3 ROOF 12 16566008 10 5 4 Moving or shipping of instrument 10 6 Trouble Shooting s tri 2112443 215121502416443304118435 330 19 052s81 4Etg283 025548Z2122x72 26aYy31123v5 35 V200 11 Enclosure Declaration of conformity 19052013RS01 eee Page 3 of 11 Model 1730R D gt SCANSPEED 1 Precautions The instrument must be installed on a flat stable horizontal and solid surface Before operating the instrument check if the rotor and the rotor lid are securely fastened Do not move the instrument when it is not completely stopped Operate with a stable amp appropriate power inlet Do not place dangerous materials within 30cm distance around the instrument Only use rotors from LaboGene ApS with appropriate tubes for centrifugation Do not use hazardous inflammable or radioactive materials as samples When it is necessary to use toxic or radioactive materials or pathogenic micro organisms which belong to the Risk Group 11 of WHO Laboratory Bio safety Manual follows national regulations Use the emergency door open function only when the door key on the control panel is not working The sample must be loaded weight balanced way not to cause imbalance The density of sample material must not exceed 1 2g ml at Max RPM or RCF Any improper handling or any usage of un qualified accessories is not able to be S S v v v v v v protected 2 TECHNICAL SPE2. SCANSPEED INSTRUCTION MANUAL v lest Bi REFRIGERATED HIGH SPEED MICROCENTRIFUGE ScanSpeed 1730R Er ass 6 at No 9 900 900 729 Model 1730R v oe LABOGENE LaboGene ApS Industrivej 6 8 Vassinger d DK 3540 Lynge Denmark Phone No 45 39 40 25 66 Fax No 45 39 95 25 66 Mail info labogene com Internet www labogene com 19052013RS01 Cat No 9 900 900 729 CopyRight 2013 SCANSPEED Page 2 of 11 Model 1730R D gt SCANSPEED Table of contents 1 PrecautiOns HH Hi h Hi Hi ii Hi 4 2 Technical Specifications wd 3 IiSfal af OIn lt lt nu nh HH hi Hi in im 5 3 1 Delivery Checklist areenaa eanne mm Gre 5 3 2 Unpacking the instrument 5 3 3 Installation place 1D 3 4 Supply the power ud 0 in cece anaiarena ranana araa a aAA E AEREA Aa OPAR AAEE ONERVA EINEN 5 3 5 On off and the door ODenn 5 lt S2 121125111511 9 111 none renn HH TH KH KH ky 5 3 6 Rotor coupling and disassembling 6 4 Operation sissies nasia 7 4 1 Control Panel 7 4 2 Function Description 7 4 3 Operation Sequence wng 4 4 Miscellaneous FUNCHONS sirean aai aE 9 5 Maintenance m murneveneveervervverensensvernennennvennennennvennennnenvennennvennennnnnnennennennnennennnennennennnensene 10 5 1 Outer part of instrument 10 5 2 Inner part of instrument
3. acceleration amp deceleration levels to protect sensitive samples Press ACC then default ACC value blinks Press the arrow button to select your preferred lever from 0 to 5 Press the Enter button to complete the setting Press DEC then default DEC value blinks Press the arrow button to select your preferred lever from 0 to 5 Press the Enter button to complete the setting 4 2 6 Program saving amp recalling v Use to save a set of setting values or call the saved setting values Saving or Editing 01 Press the PROG button longer than 2 seconds for saving your preferred set of the test values Check the message of PROGRAM SAVE at the display and any number of HH blinks 3 Press the arrow button and select a number between 01 99 Press the Enter button to complete the saving or editing Recalling To retrieve the saved program just press the PROG shortly Check the message of PROGRAM CALL at the display Choose the number with the arrow button and then press the Enter button 4 2 7 Pulse It is for simple and fast spin down As soon as it reaches to a preset RPM it is decelerated promptly 4 2 8 Fast Cool Press the FAST COOL button then centrifuge is refrigerated to setting temperature in a short time The rotor runs with low speed 1 000 rpm and green light blinks during fast cool When temperature reached to setting data operating s
4. unit 10 rpm v Speed accuracy lt 2 at maximum speed Press the RPM RCF button 2 Press the arrow button to change input value 3 Press the Enter button to complete the setting If not pressing the Enter button the setting values are disappeared but not saved 4 2 2 RCF Relative Centrifugal Force v The conversion value from RPM to RCF is calculated automatically based on the maximum radius and revolution Press the RPM RCF button twice 2 Press the arrow button to change input value 3 Press the Enter button to complete the setting 4 2 3 Time 19052013RS01 ever arken Page 7 of 11 Model 1730R D gt SCANSPEED v Time display 99 min 59 sec 2 digit display v Time is down counted after starting centrifugation Press the TIME button Display shows the default time data and hour data links 2 Press the arrow button to change hour 3 Press the Enter button to complete setting the minute data blinks automatically 4 Press the arrow button to change minute data Press the Enter button to complete setting 4 2 4 Temperature v Temp setting unit 1 C v Temp display unit 1 C v Temperature can be set from 20 C to 40 C 1C unit Press the TEMP button Default temperature data blinks in display Press the arrow button to change temperature data 3 Press the Enter button to complete setting 4 2 5 Acceleration Deceleration v Use the adjustment function of
5. CIFICATIONS 1730R with angle rotor 1730R with PCR rotor Max RPM 17 000 rpm 15 000 rpm Max RCF 27 237 xg 14 187 xg Max capacity 1 5mlx30 0 2mlx64 Temp set range 20 40 C Run time lt 99 min 59 sec or continuous Noise level lt 60 dB Acceleration levels 5 Deceleration levels 5 Program memory 100 Imbalance Recognition Automatic Rotor Recognition Automatic Motor High torque AC induction motor Safety Lid lock Power amp Frequency 220V 50 60Hz Dimension WxDxH mm 310 x 620 x 265 Weight 43 Kg for main body only CE Certification Yes Cat No 9 900 900 729 19052013RS01 CopyRight 2013 Page 4 of 11 Model 1730R D gt SCANSPEED 3 INSTALLATION The 1730R is a rotor auto recognized model But the instrument is delivered without rotor so when you turn on the machine the system tries to recognize a rotor automatically and Error 9 is appeared because of absence of rotor In this case open the door manually using the emergency door open function refer to section 4 4 1 Mount the rotor and turn off the machine and turn on again Then the instrument recognizes rotor properly 3 1 3 4 3 3 5 3 5 1 3 5 2 3 5 3 Delivery Checklist Main body 168 Power cable 168 Emergency door open tool 1ea Rotor coupling device T tool 168 User s manual 1ea Unpacking the instrument Lift the carton upward and remove the safety padding Lift the instrument on the four sides of the machine with appropriate n
6. When running the door is opened Check the door latch Stop running power off and on E3 Over temperature of motor Check the motor temperature Check supply voltage E4 LOW voltage Use AVR to provide proper voltage Check supply voltage ES MON voltage Use AVR to provide proper voltage Stop running power off and on Ee L2 oao Tuning of the firmware Download Stop running power off and on ET FE NOEN Tuning of the firmware Download E8 inbalance Check amount of samples Check weight balances of samples Check attached place of RPM sensor E9 RPM sensor recognition error Check connection of cable for RPM sensor Fail to auto recognition of a rotor Change RPM sensor Check the rotor mounting status Any wire disconnection or tuning of the instrument must be performed only by a service engineer who is authorized by LaboGene ApS 19052013RS01 Cat No 9 900 900 729 CopyRight 2013 Page 11 of 11 SCANSPEED Declaration of conformity We declare under our responsibility that the following product Model ScanSpeed 1730R High Speed Refrigerated Micro Centrifuge to which this declaration relates is in conformity with the following standard s directives or other normative document s In compliance with EN 61010 1 Safety requirements for electrical equipment for measurement control and laboratory use General requirements EN 61010 2 020 Safety requirements for electrical e
7. ction of clockwise until it is tightly assembled 13 To disassemble the rotor rotate the T tool in a counter clockwise direction To open or close of rotor lid grasp the rotor with one hand and rotate the rotor lid nut in a counter clockwise direction for open and clockwise direction for close 3 6 3 3 6 4 19052013RS01 eee Page 6 of 11 Model 1730R D gt SCANSPEED 4 4 1 AKKKKAANKANKKA Re ere AD he O 060 i G2 05 OPERATION Control Panel Q i 8 GO E 8 SBH Display LCD Shows the data of each setting Up amp down arrow Uses to change the input data Fast Cool Uses to high speed refrigeration up to the setting temperature Pulse Uses to accelerate to set RPM and decelerate rapidly Door Uses to open the door RPM RCF Uses to switch RPM RCF TIME Uses to set test time up to 99 min 59 sec 00 continuous TEMP Uses to set test temperature ACC DEC Uses to set the acceleration amp deceleration level from 1 to 5 steps 0 step means natural acc dec and speed is faster for bigger numbers of steps PROG Uses to save a set of setting values or call the saved setting values Start Stop Uses to start amp stop operation Enter Uses to complete data setting If you press the arrow button longer than 3 seconds the numbers change very rapidly and the set up is achieved faster 4 2 Function Description 4 2 1 RPM v Speed display unit 1 rom v Speed setting
8. quipment control and laboratory use Particular requirements for laboratory centrifuges EN 61000 6 1 Electromagnetic compatibility Generic immunity emission standard EN ISO 11201 Acoustics Noise emitted by machinery and equipment Following the provisions of 2006 42 EC Machinery Directive as amended 2006 95 EC Low Voltage Directive as amended 2004 100 00 EMC Directive as amended 2011 65 EU RoHS Directive 2012 19 EU WEEE Directive Lynge January 2013 4 Drad Rasmus S rensen QA Manager LaboGene ApS Industrivej 6 8 Vassinger d 3540 Lynge Denmark 08012013QA 4
9. tops automatically Be careful to check if the rotor 19052013RS01 enna Page 8 of 11 Model 1730R D gt SCANSPEED is fastened before using fast cool function Also it should be checked if the sample is safe at 1 000 rpm 4 2 9 Door Press the Door button to open the door The door is not opened while the instrument is running 4 2 10 Start Stop Pressing the Start Stop button the operation is started to run with setting or stopped to run in any case 4 3 Operation Sequence 4 3 1 Connect the AC cord to the appropriate voltage 4 3 2 Turn on the power switch located at the left side of the unit 4 3 3 The system recognize a rotor automatically 4 3 4 All of displays are blinking with beeping sound and the default setting value is displayed 4 3 5 Input the function values as your preferences or call any preferable program 4 3 6 Press the START button to start the operation 4 3 7 As soon as the set time is ended the centrifugation will be stopped according to the set deceleration level If you want to interrupt before the set time press the STOP button 4 4 Miscellaneous Functions 4 4 1 In any cases needed emergency open you can use emergency door open tool as long as the machine is idle Insert the emergency tool into the emergency door open hole at the left upside of the unit 4 4 2 Imbalance Alarm When the rotor is imbalanced and the vibration is severe the operation is urgentl
10. umber of helpers Place it to the flat space Installation place Install the machine on the solid and flat floor or table If you place the centrifuge at the slope the axis of rotation is possibly changed because of the rotor weight Install the machine about 30cm away from the wall for the efficient air circulation Install the machine at the place with appropriate temperature and humidity It also has to be maintained with the proper temperature amp humidity Install the machine at the place without any kinds of corrosive gases Supply the power 1730R model uses 110V or 220V Check proper voltage of your instrument and connect to adequate power outlet lf the power input is more than 10 of the recommended voltage or fluctuating frequently it may affect some functions of the instrument It is advised to use AVR Automatic Voltage Regulator If you want to use the instrument at other voltage range please contact us On off and the door open Turn on the instrument by pressing a switch on the left side of the machine Press the Door button to open the door Remove the protection materials inside the chamber Cat No 9 900 900 729 19052013RS01 ir Page 5 of 11 Model 1730R D gt SCANSPEED Rotor coupling and disassembling 3 6 1 Mount the rotor fitting with the motor shaft 3 6 2 Grasp the rotor with one hand and place rotor coupling device T tool at the central groove of rotor Rotate the T tool in the dire
11. y stopped with the error message on the display and the alarming sound 19052013RS01 een ark Page 9 of 11 Model 1730R D gt SCANSPEED 5 3 1 5 3 2 5 4 5 4 1 5 4 2 5 4 3 MAINTENANCE Outer part of instrument Clean the outside of the machine with a dry soft cloth If necessary dip the cloth with neutral detergents and clean contaminated parts Keep completely dry after cleaning Do not use any volatile chemicals such as alcohol benzene etc If any rust appears clean with neutral detergents and dry it Inner part of instrument Keep dry inside the chamber after every use of the machine Clean the shaft always for avoiding an imbalance during the rotation If any part is contaminated clean with neutral detergents Rotor Clean the rotor if any parts are contaminated with samples Keep dry after usage Moving or shipping of instrument If you need to move or ship the instrument be cautious to protect the shaft from any physical impact Remove the rotor and fill inside the chamber with proper materials to keep the shaft on place l is recommended to move or ship rotors separately if no original safety padding is available Cat No 9 900 900 729 19052013RS01 pe Page 10 of 11 Model 1730R D gt SCANSPEED 6 TROUBLE SHOOTING Error Possible Causes Actions E 1 Failure to reach to 200RPM within 2 Check the RPM sensor sec Check the connection of a RPM connector or a wire E2
Download Pdf Manuals
Related Search