User`s Manual of RDC644XG Control System
Contents
1. Current work time To forecast the running time of the current file the current file No is showed on the main interface and the time is accurate to 1ms Clear all count To clear the running times of every file in the memory Delete all file To delete all memory files Format speedily To format memory speedily and then all the files in memory will be deleted e Format drastically To format memory drastically and then all the files in memory will be deleted Total the total running times of all the files 8 4 2 U Disk File If the Udisk entry in figure 8 4 1 is pressed the system will show as figure 8 4 3 and the operation method is all the same as figure 8 4 1 34 Read udisk Copy to memery Figure 8 4 3 e Read Udisk read the file list in the Udisk Copy to memory copy the target Udisk file to the memory e Delete delete the selected Udisk file This system supports such file formats of Udisk as FAT32 and FAT 16 34 but it can identify them when the files are put under the root directory of Prompt Udisk The file name of more than 8 characters will automatically be cut out by the system The file name that has only English letters and digits will not show when they are copied to the mainboard The files copied from the mainboard to Udisk will be placed under the root directory of Udisk 8 5 Introduction to some alarm info When users are operating the system or when the machine is runni2. RDLC420 RDC6332G RDC6342G RDC644XG One way 5V Only one way 24V Only one way 24V Only one way 24V one way 24V compatible with 36V compatible with 36V independent for power supply but for power supply but not recommended not recommended compatible with 36V for power supply but not recommended One way digit Two way digits and Two way digits and Two way digits port and one way two way analog port two way analog port analog settable settable independently and independently and non interacted non interacted settable independently and non interacted RuiDa ACS Shenzhen Reader Technology Co Ltd Speed Jl Compatibility Support USB Support all USB Support all USB Support all USB disks disks with disks with different disks with different capacities capacities with different capacities small capacity Capacity 256M 256M 128M Fault Common Tolerance Capable of checking Capable of checking Capable of checking defective track and defective track and defective track and formatting and good formatting and good formatting and good in in fault tolerance in fault tolerance fault tolerance Input Port Two ways 4 ways two for 4 ways two for 4 ways two for general general two Tor general two for two for specialties specialties specialties Output Port 1 way low 4 ways 500mA high 4 ways 500mA high 4 ways 50
3. 8 Push Z U key to move the changing item then push X keys and Y keys to change the value when all the IP value and the Gateway value are changed push Enter key to validate the change or Esc key to invalidate the change 8 3 12 Diagnoses If the Diagnoses item is pressed the system will show as below 3l X Limit m X Limit m Y Limit Y Limit Z Limit Z Limit U Limit U Limit _ Water proti _ Water prot2 Open prot KEN Figure 8 3 9 This interface shows some system input information such as limiter status the status of the water protecting and the status of the foot switch etc When the input is validated the color frame will be green otherwise it s gray 8 3 13 Screen Origin If the Screen Origin item is pressed the system will show as below Origin locat Top left lt gt To modify press gt Modified press Enter Figure 8 3 10 There are four entries to be selected Top Left Top Right Bottom Left and Bottom Right When one is selected the previewed graph on the screen would be enantiomorphous based on X or Y direction 32 This item is only used to preview the file on the screen and it is no meaning to the machine s movement Caution 8 4 File Key 8 4 1 Memory File On the main interface if File key is pressed it will show as below Read mem file Files 300mm s TET Speed MaxP
4. A Udisk 24V HMI PC USB CNT GN CN3 ENZ z RIS lee p EXE Lr S 7 D E BA E 23 3833 222878 2 9sz28z 218 s s z elele N 6121213 Oslo t 61S Ab Si T SU E21 054 26 RD EE T E E N IIE E ES UE EE ISIS T EARS SIEG l E Compressor O Jar solenoid A ira ID vr Work status Lamp Air compressor Relay Relay Figure 7 2 1 example of output 20 lm IRR 4 PRA E 8 Operating Instruction of Panel 8 1 Introduction to the Panel and Keys 8 1 1 The whole panel Enter 369 Origin Frame m X BS an Pulse Speed MinPower MaxPower File Start Pause 8 1 2 Introduction to the Keys Reset the whole system p Get the relative origin Let the Laser to splash To track by the current file s frame 21 RuiDa ACS RuiDa ACS TRUITT IRR Bi zx E e File The management of the memory and U disc files e speed move speed Set the speed of the current running layer or set the direction keys e Set the max laser power of the current running layer or set the power of Laser Key Set the min laser power of the current running layer e b e bad To start or pause the work e D To move the X axes or the left right cursor D Y To move the Y axes or the up down cursor e Q The Z U key can be pressed when the system is idle or the work is finished On pressing this key it will show some entries in the interface each
5. ANISY ANXISX 15 14 13 12 11 0 9 Sl lt a 1a 39 e IEEE Ethernet 2 8 a la le SEXESEIEJEIEIE SENE 2 een adire scis dicendo MGR GND LED9 LEDIS RDC 644XG A LEDI LEDS Udisk N E 24V HMI PC USB CNI CN2 BE NG CNL alal s al 2 u 81 we zz L pT 313 S 29828285 222225 ISIS z 258 Ss EI R O m a dl Ee RES T TS TERRIER UE RESI TESTES TEES IESSE AAT IESSE SUE OY 4 5 V Qu 00000000 Foot Door Manual switch protection Laser On Off X Y Z U Limiter input Figure 7 1 1 example of input 19 D Shenzhen Reader Technology Co Ltd RuiDa ACS 7 2 Output All outputs are isolated through the optocoupler and 500mA current for each OC gate output each can directly drive the 6V 24V relay led lamp buzzer etc Output connection shown as below 1 1 Sum 12 19 9 8 7 6 5 4 3 2 JEANA CERE IEEE SE SIT cm mB TL lt S ergi 3 22 3128 eai esi vali 18 3 E 6 216 GEAR Can lt e T e g ALS AFE IE SEED d ele ee CN6 CNS AXISU AXISZ AXISY AXISX 15 14 13 12 11 10 9 CNRC EE Ethernet E slal E S s SEIER 3 2 died LEDS LEDIS LTEDI LEDS Tdisk ka Z RDC644XG
6. e e NY IC PE S II S 1 15 Shenzhen Reader Technology Co Ltd 5 3 Examples of RF Laser RF Laser2 RF Laserl ISI USUS vor 8 5 i i 0000000002000 i Ethernet Udisk HMI PC USB 16 RD RuiDa ACS 6 Examples of Driver Interface for Step servo Motor 6 1 Brief The input signal end of step servo motor driver employs the light coupled isolation technology For the step by step impulse signal some isolate the side OC diode from cutoff to conduction e g the valid falling edge of pulse signal inputted from the diode minus end and some do so from conduction to cutoff e g the valid rising edge of pulse signal inputted from the diode minus end When it is indicated whether the pulse signal of motor driver is the valid rising edge or the valid falling edge it will be subject to the pulse signal inputted from the minus end of side OC diode Some input signals of motor driver are independent and some are internally of common anode so some have 4 external leading out wires and some 3 wires only the pulse and directional signals are counted as shown in Figure 6 1 1 and 6 1 2 RDC644XG Controller has four groups of 3 wires motion driver interface each interface has one direction signal one pulse signal and one 5V positive output the direction signal and the pulse signal are all OC output RDC644XG controller must be common anode with the
7. green block is on this item push the Enter key to show as below Muti origin enable Origin enable1 Origin enable3 Origin enable2 Origin enable4 Set origin lt gt o Next origin lt gt Press Z U move item Modified press Enter Figure 8 3 5 28 Push Z U key to move the green block to the anticipant item and when the green block is on enable items push Enter key to enable or disable the item when enabled the small diamonds is green and when disabled the small diamonds is grey When the green block is on the Set origin item or the Next origin item push the X keys to select the value Pay attention to if when the green block is on the Set origin item push the X keys to select a value then Enter key must be pushed to valid the change or the change is invalid Each item introduced as below Multiple Origins Enable Yes or No can be selected If you select No the system will use the single origin logic You can press the Origin key and set the origin and only this origin can become valid If you select Yes the system will use the multiple origin logic and the Origin key on the keyboard become invalid In such a case the parameter of each origin must be set in the menu as follows Origin Enable1 2 3 4 after the multiple origin logic is enabled the four origins can independently be prohibited and enabled oet Origin 1 2 3 4 after t
8. motor driver The polarity of the direction signal can be changed in the factory parameters and the valid edge of the pulse signal can also be changed Figure 6 1 1 Four Inputs Independent Figure 6 1 2 Three Inputs Common anode Input Signal of Driver Input Signal of Driver D RuiDa ACS Shenzhen Reader Technology Co Ltd 6 2 Examples of Motor Driver Connection 220 VAC L 220 VAC N OV DC36V N OV 36V 36V 36V Motor d Motor d Y U X U U U V v Vi Ve Driver K Driver Nd Motor GND Motor GND Y ENA X ENA ENA ENA DIR DIR DIR DIR PLS PLS PLS PLS 15714 13212716 10 97 8 7 ooooooooo T o 2 GG kl a E AXISU 15 14 13 12 11 10 9 Ethernet Z B T ma LED1 LED8 Udisk sails PC USB 18 D 7 Examples of lO port Wiring 7 1 Input The two water protection inputs are 24V logic level all other inputs are compatible with 5V 12V 24V logic level Input connection shown as below IET le OP Oe 287 Om na on ee 2 Kalb ah ab ab ah db dh ab ab ab ab Ab db l Jj Se Ses HR RR SE RE an o E32 524 spes eese Tes 534223272 V TT 8 e EEEE T eng E Mg ig oid g al l 2 STH SHI L ED e SE EE Ee CN6 CN5 ANXISU ANISZ
9. signal used by this laser in general glass tube is about 20KHZ RF laser is about 5KHZ the maximum minimum power is used to set the limit power of this laser that is to say during the operation the maximum power set by the user can t be higher than that set here and the minimum power set by the user can t be less than that set here either When a laser s power is attenuated then the laser attenuation quotiety may be set If it is only provided with the single laser it can show the one path parameter Prompt 3 Other manufacturer parameters Machine configuration gt Machine Type In most cases the general engraving machine should be selected and other types used for specific purposes gt Transmission Mode generally the Belt Stepping Type should be made choice of The control algorithm will be changed a little when other types are selected gt Feeding Mode it has single way mode and two way mode for option If it is of single way feeding it is unnecessary to check the coordinates Feeding can be conducted in the single way mode if it is of two way feeding the system will check the maximum and minimum coordinates The odd sequence means feeding should be done to one direction and the even sequence means feeding done to the other direction The initial direction for the first time can be changed through setting the directional polarity or modifying the plus and minus values of the feeding length gt Power O
10. water protector 1 can be unconnected Water protection input must be 24V logic level The analog signals for Laser Power If Glass Tube is used this pin is recommended to control the power of the Laser ZY Please correctly select the laser type in the factory parameters Prompt 13 5 Examples of Laser Power Interface 5 1 Brief This control system has two independent and adjustable digital laser power control interfaces which can be used to control glass tube laser power and RF laser Please correctly select the laser type in the factory parameters or the laser control is incorrect D RuiDa ACS Shenzhen Reader Technology Co Ltd 5 2 Examples of Glass tube Laser Power Water protect Switch ki Laser CO2 L Cathode Anode A B Water protect Switch kint Laser CO2 Lg Cathode Anode A B GND GND Laser Powerl 15 14 13 32 3I 30779 8 6 Se Ses T SE SEXES E E SELLE BI LS CNS LAXISU AXISZ 151 14 13 12 11 10 9 E SIS esl Ethernet ce Eig S EE z 28 8 2 2 4 d GND W GU E es a ER I les EL ele Been 2 S LED9 LEDIS RDC644XG A LEDI LEDS Udisk HMI PC USB TONG zw 9 5 5 SEN 2933438828 2 Sis S 18918198 G6 6lalel 19121516 al S Ado iE c
11. 0mA high current for each OC current for each OC output no reverse output no reverse current SO additional drive current for each OC output reverse current is needed current protection current protection protection included Power off YES YES YES YES restart for awe e E LN Logics Backup YES the work time YES the work time Logics Work Preview time YES the work time accurate to 1ms accurate to 1ms accurate to 1ms Online Update Mainboard Program YES Z O O S m o Online YES YES Modification Laser Power Speed Offline Modification Layer parameters YES YES um k _ Online Update Startup Display File dynamic static preview Run progress bar display Modification Factory User s para on display Display type 128 64 320 240 TFT display 320 240 TFT display Kom YES YES NO YES O O O O 320 480 TFT display YES O Shenzhen Reader ECH Co Ltd Hard Spacing Linkage Feeding Feature Single double direction direction for option Power on Resetting Configurable for each axes D RuiDa ACS Single double direction for option Single double direction for option Configurable for each Configurable for each Key Speed Configurable Configurable Configurable 4 3 2 configurable to flat or feedin axes axes is Realtime clock and battery integra
12. 81 Fall Pol EE 29 3 3 0 Del Fact T OO ossussi esse EPUM TERDUM ISIN NE POPDI FE INPS A 30 NOR TAO FOCUS m 30 3 3710 E eM Uum 30 NERIS E 240 31 ee 12 A OS EE 3 5 3 13 Seen ONGI asioinnin naan eee ne E EE EE E EA ee Tere ee enero 32 V MINE d eebe EE 33 o4 1 Memory mE 33 GA U e 34 8 5 INTRODUCTION TO SOME ALARM INFO 35 9 MANUFACTURER USER PARAMETERS EXPLANATION sseesssocesssoeesssocesssoeesssoeesssoeesss 37 9 1 MANUFACTURER PAR AMETERS sese 37 OZ USER PARAMETER NC 40 IH 1 Overview 1 1 Briefing RDC644XG system is a new generation system for control of laser engraving and cutting which is developed by RD Co Ltd In addition to high hardware stability high voltage or static electricity rejection and friendly 3 5 TFT man machine display This system is provided with stronger software function including perfect 4 axle motion control function large capacity file storage two channel adjustable digits laser power control interface USB driver of stronger compatibility multi channel general special IO control and this system can communicate with PC by USB2 0 or Ethernet and the communication mode is automatically checked by the system 1 2 Description of Controller Model RDCO44XG Conventional Edition 320 480 TFT 4 axle Card Hardware Sub Edition Hardware Edition Laser Control RD Technical Products 1 3 Comparison of Controller Performance
13. IC IP The same as the Single controller to PC with single NIC above 43 D RuiDa ACS XIII RUAA 4 RA n STEP 2 The second NIC may be connected to internet with router So the router should be configured First 1 Open IE and input the IP address 192 168 1 1 just for most NIC And then enter the NIC configuration interface Then input the password default is Admin TP LINK Status Setup wizard aa EC Eng LAN Setup The basic LAN settings on this page e WAN Qa TM WAN Settings MAC address AS 15 4D B2 AE AF E Eege IP address 192 168 2 1 MAC Clone Wireless Setup Subnet mask 255 255 255 0 v Wireless 2 4GHz Wireless 5GHz DHCP Server Set the router IP address to be 192 168 2 1 make sure the IP to difference with other routers 2 Get the router DNS TP LINK G Vervisons Setup wizard LAN Setup Software 3 13 23 Build 130319 Rel 53557n e Wireless Setup Firmware WDR3320 v2 00000000 n Wireless 2 4GHz Wireless 5GHz DHCP Server WAN Status MAC address 8 15 4D B2 AE BO IP address 183 14 140 230 PPPoE auto connect Subnet mask 255 255 255 255 183 14 140 230 Routing rules Security function Parental control Net control Routing function Time of net 1 day s 20 29 36 Disconnect IP bandwidth control Record the DNS server 3 Configure the second NIC IP address and DNS server Seen as follows 44 General You c
14. OF GLASS TUBE LASER DOWER rennen nnne shes urhe tasse ste stessa eser testes t ene 15 5 3 EXAMPLES OF RASE 16 6 EXAMPLES OF DRIVER INTERFACE FOR STEP SERVO MOTOR e e 17 MIS MMNMMKU PE20ROIA 17 6 2 EXAMPLES OF MOTOR DRIVER CONNECTION 18 7 EXAMPLES OF IO PORT WIRINGQ 4 e eee eee eee een eere eene eee e ette eso etes sese eese see esses es aasa 19 F NC E RRRRD e 19 5 324 8 BU 14 ER TTT 20 8 OPERATING INSTRUCTION OF PANEL cc cccecccccccccccccccccoccccoocco00c0000c000c0000000000000000000000000 21 8 1 INTRODUCTION TO THE PANEL AND KEYS 21 8 1 1 The whole panel ssrsanursssoiierninniiemaen a aa a E a eeka aiei 21 II 8 4 2 Introduction To the EE 21 5 2 INTRODUCTION TO THE MAIN INTEREAQG Eni aaae AREA AEZH aOd oiai Ear 23 3 2 1 Th main Bierre 23 5 2 2 8D6EU E 24 8 2 3 Max Min power E 24 8 2 4 Set the layer parameters ssssssssssssssse eene ee e ee eene nenne enne nennen nennen nns 25 L 08 qo P 26 EUN IPAE 1107 26 CO IOC E YY 9 0 26 3 33 AXIS TOSO ARE CRA CT 26 Dod Maa Ee 27 386 E48 E21 ENG eee 28 E Eelere EE 28 e 5
15. Start Pause GL Reset Figure 3 2 1 Object Picture of Panel RuiDa ACS D RuiDa ACS Shenzhen Reader Technology Co Ltd 3 3 Electric connection L 220 VAC L 220 VAC lt 1220 VAC N N Water protect Switch Ethernet cable ov gt Laser CO2 24V Ad e Cathode AC220 D 220 VAC L C gt y Anode Ac220 24V gt DC36V oY Laser svi 24V LD gt D ov 5 D 36V 5 Power GNDD 36V gt wP 5 36V gt R TLI gt L r T n FF L L H H wD wD Vv v ovrrvr v v 1 Zn Motor yB Motor YR oF Y uD X uD T TEL vH uH 15 00 14012 11710 BES 495201 Driver VP Der E o0000000002020000 Motor NOD Motor NOD 3 3 3 2 Y ENA gt c 5 r 5 ENA X a D 6 8 IP G ar S gt PLS lI dasdi PLS LD Ethernet 341321031 EEE EEE aja 51218 s 3 s eJ a 3 2 8E SE Udisk gt HMI PC USB Usb cable Compressor solenoid T Air compressor V U A EI UA z O Ororo OF OF OF OF C9 0 E o e i Current Work status Lamp limiter Pl a 2 9 Jj Em O Ou LTA OOO OID Foot i Door Manual XUZVU limiter Switch protection Laser on off Figure 3 3 1 electric connection 4 Description of Interface Signal for MainBoard 4 1 Interface of Main Power Source CNO Symbols Definitions Pin This control system employs single 24 power supply For a certain margin it is suggested to select 24V 2A power Besides thi
16. User s Manual of RDC644XG Control System Shenzhen Reader Technology Co Ltd RD Co Ltd Copyright Declaration Shenzhen Reader Technology Co Ltd reserves all rights Shenzhen Reader Technology Co Ltd hereinafter referred to as RD Co Ltd holds the patent right copyright and other intellectual property rights for this product and its related software Without authorization no one is allowed to copy manufacture process and use this product and its relative parts directly or indirectly RD Co Ltd is entitled to increase or reduce and modify the shape and functions of this product stated herein as well as amend any documents attached to this product without prior notification The users should peruse this Manual prior to using the product stated herein RD Co Ltd Shall not be responsible for the direct indirect special incidental or corresponding losses or damages arising out of improper use hereof or of this product The machine in operation is dangerous so the users are obliged to design and institute the effective mechanism for error handling and safety protection RD Co Ltd shall not undertake any duties or responsibilities for the incidental or corresponding losses arising therefrom II Version History V1 1 The original version V1 2 1 The sixth pins definition of CN3 and CN4 is changed 2 The fifth pins definition of CN5 and CN5 is changed 3 Some explanation of the user parameters is ch
17. acceleration can be set higher to reduce the working time of the whole figure but if they are set too high it may cause the jarring of track so comprehensive consideration should be given to the setting Idle Move Delay If this parameter is zero then after idle moving there is no delay or there is delay and the speed will decrease to turn off speed Turning Speed it means the speed of turning at the acute angle corner which is also the highest speed in the whole cutting process Turning Acceleration it means the acceleration of turning at the acute angle corner when cutting If the two speeds are set too high jarring will happen to the turning if set too low it will influence the cutting speed This acceleration is the least value of the whole graph Cutting Acceleration it means the highest acceleration value in the whole cutting process Acc Factor This parameter indicates how speedy the cutting acceleration is changing GO Acc Factor This parameter indicates how speedy the idle move acceleration is changing Speed Factor This parameter indicates the cutting speed of the arc of various curvatures Key Setting This is a button but not a parameter this button is used to recommend some experiential cutting parameters 2 Scanning parameters Only affect scanning arts 40 V V V V X axle Starting Speed Y axle Starting Speed X axle Acceleration Y axle Acceleration The above four parameters are used to set the sta
18. an get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 1907 188 2 21 Subnet mask 255 255 255 Dn Default gateway 1922 188 2 1 Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server 202 96 134 33 Alternate DNS server 202 96 128 88 Validate settings upon exit e PC and Multi controller to concentrator Concentrator PC controller controller2 O controllerx 1 PC connects the input of the concentrator Multi controller connects to the output of the concentrator 2 Different IP address should be configured for every controller But all of the IP address should be set between 192 168 001 100 192 168 001 149 3 Then set the PC IP address between 192 168 001 2 192 168 001 049 PC and Multi controller to concentrator And the 45 concentrator connects to router router input Concentrator output PC controller controller2 o o o controllerx 1 PC and multi controller connect to output on the concentrator 2 Different IP address should be configured for every controller But all of the IP address should b
19. anged 4 Some of the Object Pictures of MainBoard silk screen is changed CONTENTS OVERVIEW oae E E E N 1 L E O EE l 1 2 DESCRIPTION OF CONTROLLER MODEL 1 1 3 COMPARISON OF CONTROLLER BPEREORMANCE eene rer erererererererereretere rere on l 2 INSTALLATION TEE 4 2 1 INSTALLATION SIZE OF MAINBOARD EE 4 22 SAP OF T 5 3 OBJECT PICTURES AND INTERFACES ccecccceccccccccccccccocccocccoscccooocoooocoooecoocccuoccuoecouescuueus 6 3 1 OBJECT PICTURES OF MAINBONMXRD ioc xeseecedevewenweedandlebvacodeaidavedsewecexweseondeaseanes 6 32 OBIECT PICT IRES OF TET 7 3 3 ELECTRIC CONNECTION EE 8 4 DESCRIPTION OF INTERFACE SIGNAL FOR MAINBOARD ccccsccsssccccsssccceees 9 4 1 INTERFACE OF MAIN POWER SOURCE CNU enne en enne ererne terere estere teret enis 9 4 2 PANEL SIGNAL CABLE INTERFACE HM 9 4 3 UDISK INTERFACE Rm Em 9 4 4 PC USB INTERFACE ee 9 4 5 ETHERNET ER E e DEE 9 4 6 GENERAL OUTPUT PORT CNT 10 4 7 GENERAL INPUT PORT OCN EEN 10 4 8 4 AXLE SPACING INPUT INTERFACE CN 3 CNA ccc cecceeccceccecccecccesccesccusccesccaeccesccasccusccueseaecensens 11 4 9 X Y Z U AXLE MOTOR DRIVER INTERFACE AXIS X AXIS U 12 4 10 LASER POWER CONTROL INTERFACE CNSCNG eher eee tese teee tese esee serene 12 5 EXAMPLES OF LASER POWER INTERFA QG E e ecce ee eee eere eene e eo aa anana aaa ananas 14 ABI MEE 14 5 2 EXAMPLES
20. aximum limit of motion speed that this axle can bear This parameter has something to do with the driving force of motor the inertia of motion axle and its drive ratio For example the typical value is 200 500mm s Maximum Acceleration it means the maximum acceleration of the motion axle in accelerated or decelerated motion If the acceleration is set too large it will make the motor lose steps jar and even squeak if too small it will cause the reduction of acceleration so as to reduce the running speed of the whole figure For the axles with larger inertia such as Y axle corresponding to the beam its typical setting range is 800 3000mm s2 for the axles with smaller inertia such as X axle corresponding to the car its typical setting range is 8000 20000mm s2 Scram Acceleration if this axle enables the hard spacing protection when this axle moves to the spacing position it will scram operation at the scram acceleration This value can be 2 3 times of the maximum acceleration for this axle Key parameters Key Move Takeoff Speed it means the starting speed to move this axle by way of the keys on the keyboard which can t be higher than the takeoff speed Key Move Acceleration it means the acceleration to move this axle by way of the keys on the keyboard which can t be higher than the maximum acceleration of this axle Key Polarity it is used to control the movement direction of the axle that is moved through manual operation of th
21. e keys After the direction polarity is correctly set if you press the directional keys on the operating panel this axle will move to the opposite direction In such a case the polarity of keys should be modified 2 Laser parameters Y Y V V V V Laser Configuration single laser and double lasers are available for option and set in accordance with the laser tube quantity provided by the manufacturer Laser Type glass tube RF laser not need pre ignition pulse and RF laser needing pre ignition pulse available for option Laser Attenuation Quotiety Laser Enable When double lasers are used then each laser can be respectively enabled or disabled Minimum Power Maximum Power Laser PWM Frequency Pre generation Frequency 38 gt Pre generation pulse scale When the laser is RF laser and its need to pre generate PWM then set the Pre generation Frequency and the Pre generation pulse scale gt Water Protector Enabled When the water protector is enabled the mainboard will detect the input port of water protector If this port is of low level it will be deemed normal if this port is of high level the mainboard will forcibly close the laser to suspend the work in progress and the system will warn If the water protector is not enabled the mainboard will not detect the input port of water protector and so the water protector can be unconnected Laser PWM Frequency is used to set the pulse frequency of control
22. e set between 192 168 001 100 192 168 001 149 3 Configured step please reference to Single controller to PC with multi NIC 46
23. entry includes some functions Z axes move U axes move each axes to go home etc To stop work or to exit to some menu e E e Enter Validate the change 22 8 2 Introduction to the Main Interface 8 2 1 The main interface When the system is powered on the screen will show as below Running parameters Graph display area IN File 01 Speed 300mm s MaxPow 30 0 30 0 Y 153 5 T ZEE 3000 E Coordinate m Graph layer Running parameters i Ze r 4 99 X 180 5 mm Y 235 6 mm connect as Figure 8 2 1 Running Status Working Number e Graph Display Area To display the whole file s track and display the running track e Running parameters To display the running file s file number speed max power etc Coordinate To display the current coordinate of X Y and Z axes e Graph layer parameters To display the layers information of the current file such as max or min power speed etc When system is idle dblclick the layer then users can change the layer s parameters and the changing would be saved e Running Status To display the current status of the machine such as Idle Run Pause Finish etc Running Progress Bar To display the progress bar of the current running file Working Number To accumulate the work number of the current file File Dimension To display the dimension of the current file Net status To display t
24. ff Restart Delay it can be set to be 0 3000ms After the power off of the electricity grid the power supply of the system will not drop to 0 at once There is a delay during this time The delay value set here should basically consistent with the actual off delay value If the deviation of set value is larger on the de energizing for continuous engraving either the figure processed for the second time is not closed with that before the cutoff or it is coincided with that too much 39 Y After the configuration parameters in the manufacturer parameters such as directional polarity control mode laser type and laser PWM Prompt frequency are modified the system should be reset Such a modification gt gt can function upon the resetting of the system Enable parameters Door Opening Protection If this item is enabled then the door opening protection must be connected to the controller or the machine will not run Whether to enable the blower If using wind out port to control the blower by the graph layer parameter this item must be enabled or the wind output is a signal for other using 9 2 User parameters 1 Cutting parameters Only affect cutting arts Idle Move Speed this parameter decides the highest speed of all non lighting lines for the machine in the movement process Idle Move Acceleration it means the highest acceleration of all non lighting lines Idle stroke speed and idle stroke
25. he connecting status of the Ethernet When work is Idle or finished all keys can be pushed users can select a file to run 23 EE set some parameters preview to a select file etc But when work is running or paused some keys don t respond when they are pushed 8 2 2 Speed key Push the Speed key when the screen is on the main interface it will show as below Modified press Enter Figure 8 2 2 Push the X Keys to move the cursor in the numeral area and push the Y keys to change the value then push the Enter key to save the change push the Esc key to invalidate the change 8 2 3 Max Min power keys Push the Max Power or the Min Power keys when the screen is on the main interface it will show as below MaxPowerl 30 0 MaxPower2 30 0 Press Z U move item Modified press Enter Figure 8 2 3 24 MinPowerl 30 0 MinPower2 Press Z U move item Modified press Enter Figure 8 2 4 When Z U key is pushed the green block can move up and down to denote the changing item then Y keys and X keys can be used to change the value 8 2 4 Set the layer parameters After selecting a file to preview on the main interface user can push Enter key to let the cursor move to the first layer then Y Keys can be pushed to select the intent layer on that time user can push Enter key to check the selected layer s pa
26. he multiple origin logic is enabled you can stop the cursor at Set as Origin 1 2 3 4 Press the Enter key on the keyboard and the system will take the coordinate figures of current X Y axles as the corresponding ones to the origin 1 2 3 4 Next Origin there are such five digits as 0 4 for option which are the origins to be used for the next figure Origin 0 means the origin set by the Origin key on the panel in the single origin logic 1 4 means the serial number of the origins in the multiple origin logic Next origin can be modified to any one of origin 1 4 so as to control the start location of next work the premise is that the origin is enabled but it can t be modified to origin O Once the multiple origin logic is selected and if the serial number of the next origin is 1 and four origins are enabled when the memory file function is started or the processing file is uploaded into the PC and this file selects Take the Original Origin as current Origin the work started for each time will use different origins The rotation order of origin is 1 gt 2 gt 3 gt 4 gt 1 gt 2 8 3 7 Set Fact Para After the Set Fact Para is selected and the Enter key pressed the interface will show the specific password to be entered when set as default parameter 29 Password Password error 0123456789 ABC DEFGHIJ KLMNOPQRST UVWXYZ Figure 8 3 6 Push X keys and Y keys to select the characters and push
27. ng some alarm information such as water protecting error maybe shows as below 35 Water error Figure 8 5 1 Push Enter key or Esc key the system will execute some relative steps 36 9 Manufacturer User Parameters Explanation 9 1 Manufacturer parameters 1 Motor parameters X Y Z U axle parameters Direction Polarity Modification of direction polarity can move the motor to the opposite direction The modification purpose can move this axle to the origin on resetting If this axle moves far from the origin on resetting it means the direction polarity of this axle is wrong in setting and should be modified Spacing Polarity it is used to set the high and low level mode of spacing signal When the motion axle arrives at the spacing position and input a low level signal to the mainboard the spacing polarity at this time should be set to be minus gt scope it means the farthest distance that the motion axle can move which is determined in accordance with the actual condition of the machine Distance from Origin to Hard Spacing if this axle enables hard spacing protection generally this value should be set to be 2 5mm if it is set to be O when this motion axle moves to the smallest coordinate i e O this spacing may be validate which may wrongly triggers the hard spacing protection and scram the machine If the hard spacing protection is not enabled this value can be set to be 0 5mm gt Con
28. ow 30 0 30 0 A C D Others 1 502 lum Track 3000 mm Work time Clear count Delete Copy to udisk Idle 00 00 00 Count 99 X 180 5 mm Y 235 6 mm connect Figure 8 4 1 When showing this menu the system would read the memory file firstly the file name and the work times would be listed in the area and the selected file is previewed in the bottom right area Y keys could be used to move the cursor on the file name list When the cursor is on a target file name presses the Enter key the selected file will be previewed on the main interface and then if Esc key is pushed the preview will disappear X keys could be used to move the cursor left and right All the item show as below Read mem file read the memory file list Udisk read the U disk file list Other the other operation of the memory files e Run To run the selected file Track To track the selected file and the track mode is optional Work time To forecast the running time of the selected file and the time is accurate to 1ms Clear count To clear the running times of the selected file 33 Delete To delete the selected file in the memory Copy to Udisk To copy the selected file to Udisk If the Other entry is pressed the system will show as below Current work time Clear all count delete all file Format speedly Format drastically Total 10 Figure 8 4 2
29. ower switch can be set separately on each layer If the relay is connected externally the relay coil will be broken over when the blower is on the relay coil will be cut off when the blower is off 24V Power positive output If the interface of main power source is powered with 24V power supply this pin should be 24V if it is powered with 36 V power supply this pin should be 36V All outputs are isolated through the optocoupler and 500mA current for each OC gate output each can directly drive the 6V 24V relay 4 7 General Input Port CN2 Pin Symbols Definitions 1 GND Power ground output FootSW Input port of foot switch The connection method is when the pedal is stepped down the low level signal will be inputted to this port when the pedal is released the port will be disconnected or the high level signal can be inputted to this port when the stepped down pedal is held for not less than 100 ms if the machine lies idle it can be started for work if the machine is in the working state the work will be suspended of the machine is in the suspension the work will 10 be restarted that is to say the function of the pedal switch is the same as that of the Start Pause key If the interval time to the first stepping down of the pedal should be less than 100ms when the pedal is stepped down once again the second stepping down of the pedal will be considered invalid by the mainboard DrProc Input from protecti
30. rameters show as below Figure 8 2 5 Speed 4 MinPowerl 22 0 MinPower2 30 0 MaxPowerl MaxPower2 3 Press Z U move item Modified press Enter Figure 8 2 6 25 User can push Z U Keys to move the green block on the intent parameter then he could change the parameter if needed OK to validate the change and Esc to invalidate the change 8 3 Z U Key The Z U key can be pressed when the system is idle or the work is finished On pressing this key it will show some entries in the following interface Z move Language U move IP setup Axis reset Diagnoses Manual Set Screen Origin Laser Set Origin set Set Fact Para Def Fact Para Auto Focus zme Figure 8 3 1 Push Y keys to move the green block to the anticipant item and then push the Enter key to display the sub menu 8 3 1 Z move When the green block is on Z Move item X keys can be used to move the z axes 8 3 2 U move When the green block is on U Move item X keys can be used to move the u axes 8 3 3 Axis reset When the green block is on this item push the Enter key to show as below 26 RuiDa ACS AIN IRR BA HR n XY axis reset X axis reset Y axis reset Z axis reset U axis reset Figure 8 3 2 Push the Y Keys to move the cursor to one of the entry then push Enter key to restart the selected axis the
31. rting speed and acceleration of two axles on the scanning The higher the two speeds are the quicker the scanning is Scanning Line feed Speed this parameter is specially used to control the highest speed at which that the previous line vertically moves to the next line in the scanning mode If the space between lines is larger during the scanning or if the distance of each block is larger during the scanning and deblocking of figure it is necessary to position each line or block accurately In such a case the speed of scanning line feed can be set as a lower value Scanning Mode it is divided into general mode and special mode for option If special mode is used the laser power should be increased The smaller the speckle percentage is the more the laser power reduces The laser power to set should be larger _ _ar to reach the same scanning depth The purpose to select the special mode is to make the laser light at high power and short time On the depth scanning the effect that the bottom is flatter is obtained but it should be noticeable that if the speckle adjustment is not appropriate it can achieve this goal If the high power remains short the lighting mode will influence the life of the laser The system will default the selection of general mode Speckle Size When the general mode is selected as the scanning mode this parameter will become ineffective when the special mode is selected this parameter will become effective The con
32. rtup 4 Go scale parameters gt Go scale Mode Blanked Bordering means idling to start border preview Outputted Border Cutting can manually cut off the well processed figure 4 corner Dotting means to emit the light at four corner points of the frame to make a point and turn off light The size and position of this figure can be checked intuitively through the four points The bordering speed is the speed value set on the keyboard when the system is idle For light output its minimum maximum power is the corresponding value set on the keyboard when the system is idle The lasering power on the 4 corner dotting means the well set maximum power gt Go scale Blank It means whether to extend a certain length outside the actual frame of the figure on the preview cutting of frame If the frame crosses the border the interface will prompt it If the Enter key is pressed at this time the system will cut the border at the Prompt maximum minimum coordinates first and then border the figure This bordering can be given up 5 Other user parameters gt Array Mode Two way array or one way array can be selected Two way array means the to and fro cutting of array in sequence one way array means the cutting of array from one direction to another On selecting one way array the elements of each array are the same in action mode and completely uniform in action fluency which takes a little more time than two way array Two wa
33. s The Controller must be common anode with the motor driver Prompt 4 10 Laser Power Control Interface CN5 CN6 This control system has two independent and adjustable digital laser power control interfaces Signals of the two interfaces are similar and the first digital interface CN5 is hereby exampled Pin Symbols Definitions 1 GND Power ground output L ON1 Laser enabled control interface 1 When the laser is the RF laser this pin will not be used 2 When the laser is a glass tube if the used laser is outputted in the low level form this pin will be connected with the laser power enable end and used to control the ON Off of laser Power control interface of laser laser tube 1 When the laser is the RF laser this pin will be connected with the laser RF PWM end 2 When the laser is a glass tube this pin will be connected with RuiDa ACS Shenzhen Reader Technology Co Ltd the laser power PWM end and used to control the power of the laser The input port of water protector for the first laser power source When the water protector 1 is enabled the mainboard will detect the input port of water protector 1 If this port is of low level it will be deemed normal if this port is of high level the mainboard will forcibly close the laser to suspend the work in progress and the system will warn If the water protector 1 is not enabled the mainboard will not detect the input port of water protector 1 and so the
34. s system is compatible with 36V power that is to say the 36V power of Motion driver can directly be connected to this main power port of this system but generally it is not suggested to do so 4 2 Panel Signal Cable Interface HMI The panel signal cable is a pin to pin cable which is included in the factory shipper bill 4 3 Udisk Interface Udisk is a USB AM interface The controller may visit the u disk by this interface 4 4 PC USB Interface PC USB is a USB BM interface The controller may communicate with PC by this port 4 5 Ethernet Interface Using this interface the mainboard can communicate with PC by 10 100MHZ Ethernet Pin to Pin Ethernet parallel line is recommended Caution 4 6 General Output Port CN1 Definition of general output port Symbols Definitions GND Power ground output Out2 General output with the function reserved Out General output with the function reserved Status General output for the signal port of running status If this port is externally connected with the relay the relay coil is broken over when it works no influence is produced when it suspends working When its work ends or is stopped manually the relay coil will be cut off General output for blower control When the blower control is enabled this port will output the control signal of the blower otherwise it will output other special control signals When the blower is connected and its control enabled the bl
35. screen will show some information when resetting 8 3 4 Manual sett When the green block is on this item push the Enter key to show as below manual mm Press Z U move item Modified press Enter Figure 8 3 3 Push Z U key to move the green block and when the green block is on the Mode item push X keys to select the anticipant value Continue or Manual When Continue item is selected then the Manual item is not valid on that time push the direction keys to move the corresponding axes and when the pushed key is loosed then the corresponding axes will finish moving When the Mode item is manual then pushing the direction key one time the corresponding axes will move a fixed length unless the scope is overstepped 27 8 3 5 Laser set When the green block is on this item push the Enter key to show as below Laser Set ms Press Z U move item Modified press Enter Figure 8 3 4 Push Z U key to move the green block and when the green block is on the Mode item push X keys to select the anticipant value Continue or Manual When Continue item is selected then the Laser Set item is not valid on that time push the Laser key to splash the enabled lasers and when Laser key is loosed then the lasers will finish splashing When the Mode item is manual then pushing the Laser key one time the enabled lasers will splash a fixed time 8 3 6 Origin sett When the
36. ted for hardware encryption 10 100MHZ Ethernet or USB2 0 Encryption based on the 3 Z axes is 4 configurable to flat or feedin axes Realtime clock and battery integrated for hardware encryption 10 100MHZ Ethernet or USB2 0 No realtime clock but encryption included 10 100MHZ Ethernet or USB2 0 communication mode checked is automatically 2 Installation Size 2 1 Installation Size of MainBoard The unit of all sizes is millimeter mm and the size accurate to 0 1mm the four holes are symmetrical Figure 2 1 1 2 2 Size of Panel The unit of all sizes is millimeter mm and the size accurate to 0 1mm i 170 108 Q PSS SS SSS SS EE E ET SES Re CN p mI Figure 2 2 1 RuiDa ACS Shenzhen Reader Technology Co Ltd 3 Object Pictures and Interfaces 3 1 Object Pictures of MainBoard For more detailed pin description see the Chapter 4 Description of Interface Signal for MainBoard EE EE ae GND z LED9 LED15 RD C 644XG A LEDi LEDS Udisk 24V HMI PC USB Figure 3 1 1 Object Picture of MainBoard Shenzhen Reader Technology Co Ltd 3 2 Object Pictures of Panel iB H fi XE Esc Enter E fil Origin Frame Ei Bx B SH Pulse Speed MinPower MaxPower File
37. the Enter key to valid the characters when finishing enter the password that is to say the six characters if the password is error it prompts there is some error or all parameters are stored After the manufacturer regulates all parameters of the machine well including all manufacturer parameters and user parameters this function can be used to store the well regulated parameters to help users to recover the original parameters including all manufacturer parameters and user parameters through selecting Recover Para when they regulate parameters improperly 8 3 8 Def Fact Para After the Def Fact Para is selected and the Enter key pressed the Successful Recovery dialog box will pop up to prompt that all manufacturer parameters and user parameters are recovered successfully You can return to the previous menu by press the Enter key 8 3 9 Auto Focus When the cursor stops at Auto Focus press the Enter key to search for the focus When there is z axes and the z axes reset function is enabled the auto focusing is valid press the Esc key to return the prior menu 8 3 10 Language The item Language helps you to select a appropriate langue which is displayed on the pane 30 5m Tradition English Figure 8 3 7 8 3 11 IP Setup When the green block is on this item push the Enter key to show as below IP address Gateway Press Z U move item Modified press Enter Figure 8 3
38. trol Mode Double pulse or direction single pulse are optional in general direction single pulse is selected Motor Stepping it means the impulse equivalent the absolute distance gone by the corresponding motion axle when a pulse is delivered to the motor Prior to the correct setting of this value a large rectangle can be cut with the machine the larger the figure is the smaller the difference is The motor stepping can automatically be calculated according to the figure length and measuring length Hard spacing Protection it is used for whether the hard spacing protection of this axle is enabled gt PWM Rising edge valid To set the motor driver s pulse signal rising edge valid or falling edge valid If this item is disabled the pulse is falling edge valid or it s rising edge valid Reset Enable if the machine is provided with this axle its Reset Enable should be opened if no its Reset Enable should be prohibited Takeoff Speed it means the speed of the motion axle in direct start from the idle condition If this value is excessively large it will make the motor lose steps jar and even squeak if small it will reduce the running speed of the whole figure If the inertia of the motion axle is larger the axle is heavier you can set a smaller 37 takeoff speed if smaller the axle is lighter you can increase the takeoff speed For example the typical value is 5 30mm s Maximum Speed it means the m
39. troller will control this parameter among 50 99 The cutting and scanning parameters can t exceed the limited ones in the axle parameters If so the setting will become ineffective and the system will automatically cover the parameters with the axle parameters 3 Feeding parameters Before feeding Time Lag settable at 0 300s The lagged time can facilitate user s feeding and picking on the feeding device After feeding Time Lag settable at 0 9 9s It can facilitate the feeding device s delaying in jarring after moving to the correct position and waiting for the 2 work after the feeding axle stands still completely Progressive feeding If this item is enabled then the dummy array graph on Y direction will run in the same position running one line graph the U axes moving one time to feed the moving length of U axes is the interval of the two lines graph on Y direction Progressive feeding repay Because of the imprecision of U axes moving there can set a value to repay the interval of the two lines graph on Y direction 41 4 Reset parameters Reset Speed it means the speed of X Y axle linkage reset to the origin X axle start up reset Auto home Y axle start up reset Auto home Z axle start up reset Auto home V V V V Y U axle start up reset Auto home You can select Yes or No in the field of the above four parameters which is used to confirm whether each axle can be reset on the sta
40. ut but when it leaves the spacing the corresponding indicator will light and the spacing polarity become positive The mistaken setting of spacing polarity will result that the spacing can t be detected when the system is reset so as to lead to the collision of axles The pin definitions of Z U axle spacing input CN3 are the same as CN4 11 All XYZU axle spacing inputs are compatible to 5V 12V 24V logic level inputs 4 9 X Y Z U axle Motor Driver Interface AXIS X AXIS U The interfaces of the above four motion axles are the same The AXIS X interface is exampled Symbols Definitions DIR Directional signal OC output PUL Pulse signal OC output 5V 5V Power positive output The polarity of directional signal for driver pulse signal can be set Where a certain axle is reset it will move to the opposite direction of machine origin which means the polarity of directional signal for this axle is not correct In such a case the connection between this axle and the motor driver can be broken first otherwise the mainboard can not be detected to the spacing so as to lead to the collision of this axle and then such a polarity can be corrected after this axle is reset completely Upon the correction the reset key can be pressed against to reset the mainboard And the Pulse signal can be falling edge valid or rising edge valid The default setting is falling edge valid The Pulse signal and the directional signal are all OC output
41. ve port If the machine needs to be protected in the special state such as door open protection the protective signal can be inputted from this pin This pin can be enabled and prohibited This signal is not inquired by the mainboard if this pin is prohibited if this pin is enabled when the input is high leveled or this input port is suspended the machine will be protected the work suspended and the laser closed Input for manual laser on off Low level is to open laser and high level or no connection is to close laser General Input with the function reserved 24V Power positive output If the interface of main power source is powered with 24V power supply this pin should be 24V if itis powered with 36 V power supply this pin should be 36V 4 8 4 axle Spacing Input Interface CN3 CN4 X Y axle spacing input CNA Symbols Definitions Power ground output The spacing from axle Y and Y to O coordinate The spacing from axle Y and Y to max coordinate The spacing from axle X and X to 0 coordinate The spacing from axle X and X to max coordinate 5V Power positive output The spacing polarity is optional that is to say when the motion axle reaches the spacing position it will trigger a low level signal so as to make the corresponding LED under the cover light when the motion axle leaves the spacing position it will trigger a high level signal or disconnect the spacing signal so as to make the spacing indicator go o
42. y array is the default option gt Back Position The origin the relative origin and the machine s absolute origin can be selected This parameter decides the parking position of laser head after each work gt Focus Setting it means the distance from the focal point of laser head lens to Z axle origin When there is no automatic focusing function this parameter becomes invalid gt Backlash X The X axes backlash accurate to 1um gt Backlash Y The Y axes backlash accurate to 1um 42 10 controller to PC with single NIC Single controller to PC with single NIC STEP 1 Set the work mode to be ETHERNET on the panel And then set the controller IP address between 192 168 001 100 192 168 001 149 STEP 2 Set the IP address in the PC The IP address is between 192 168 001 2 192 168 001 049 Reference to picturel 1 General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address Subnet mask 200 i200 299 D Default gateway 122 SI d x i Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server _ Validate settings upon exit Picturel 1 PC IP configuration e Single controller to PC with multi NIC STEP 1 set the first N
Download Pdf Manuals
Related Search