Home

PEB-6530VL User`s Manual

1. Standby M ode When enabled and after the set time of system nactivity the fixed disk drive and the video would be shut off while all other devices still operate at full speed The choice 1 Min 2 Min 3 Min 4Min 5Min 6 Min 8Min 10 Min 12 Min 15 Min 16 Min 20 Min 30 Min 40 Min Disabled HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active The choice 1 Min 2 Min 3 Min 4Min 5Min 6 Min 8Min 10 Min 12 Min 15 Min 16 Min 20 Min 30 Min 40 Min Disabled Power Down amp Resume Events Power Down and Resume events are I O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode In effect the system remains alert for anything which occurs to a device which is configured as On even when the system isin a power down mode The following is a list of IRQ s Interrupt ReQ uests which can be exempted much as the COM ports and LPT ports above can When an 17 O device wants to gain the attention of the operating system it signals this by causing an IRQ to occur When the operating system is ready to respond to the request it interrupts itself and performs the service PEB 6530VL User s Manual 4 20 BIOS Setup Information As above the choices are ON and OFF OFF is the default When set OFF activity will neither prevent the system from going into a
2. installed in the computer No floppy drive installed 360K 5 25 in 5 1 4 inch PC type standard drive 360 kilobyte capacity 1 2M 5 25 in 5 1 4 inch AT type high density drive 1 2 megabyte capacity 720K 3 5 in 3 1 2 inch double sided drive 720 kilobyte capacity 1 44M 3 5 in 3 1 2inch double sided drive 1 44 megabyte capacity 2 88M 3 5 in 3 1 2inch double sided drive 2 88 megabyte capacity PEB 6530VL User s Manual 4 8 BIOS Setup Information Video The category selects the type of video adapter used for the primary system monitor Although secondary monitors are supported you do not have to select the type in Setup EGA VGA Enhanced Graphics A dapter Video Graphics Array For EGA VGA SEGA SVGA or PGA monitor adapters CGA 40 Color Graphics A dapter power up in 40 column mode CGA 80 Color Graphics A dapter power up in 80 column mode MONO Monochrome adapter includes high resolution monochrome adapters HaltOn The category determines whether the computer will stop if an error is detected during power up be detected be stopped and you will be prompted stop for all other errors all other errors All But Disk Key The system boot will not stop for a keyboard or disk error it will stop for all other errors Memory The category is display only which is determined by POST Power On Self Test of the BIOS Base M emory The POST will determine the amount of base or conventional memory
3. PCI VGA Palette Snoop Disabled Disabled Enabled OS Select for DRAM gt 64 Non OS2 Non OS2 OS2 Report No FDD for VVIN95 No Yes Video BIOS Shadovv Enabled Enabled Disabled C8000 CBFFF Shadovv Disabled Disabled Enabled DCO00 DFFFF Shadow Cyrix 6x86 MII CPUID Enabled Enabled Disabled e Chipset Features Setup Table BIOS Setup Items BIOS Default Setup Default Other Options SDRAM CAS latency Time 3T 3T 2T Auto SDRAM Clock Ratio Div By 4 4 3 16 bit O Recovery CLK 5 5 Laj 16 8 bit 17 O Recovery CLK 5 5 1 16 USB Controller USB Enabled Enabled Disabled Legacy Support Multiple Monitor Support M B First M B First PCI First Video Memory Size 4 0M 4 0M 1 5M 2 5M None PEB 6530VL User s Manual 4 4 BIOS Setup Information e Integrated Peripherals Features Setup Table BIOS Setup Items BIOS Default Setup Default Other Options IDE HDD Block Mode Disabled Enabled Primary Secondary IDE Enabled Enabled Disabled Channel IDE Primary Secondary Auto Auto Mode 0 Mode 4 Master Slave PIO Mode IDE Primary Secondary Disabled Auto Masteri Slave UDMA KBC Input Clock 8M Hz 8M Hz 6M Hz 12MHz 16M Hz Onboard FDC Controller Enabled Enabled Disabled Onboard Serial Port 1 Port 2 3F8 IRQA 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 2F8 IRQ3 2F8 IRQ3 Disabled Auto Onboard Serial Port 3 Port4 3E8 IRQ9 3E8 IRQ9 3F8 2F8 2E8 IRQ10 2E8 I
4. The choice from 1to 16 CPU clocks 8 bit I O Recovery CLK The I O recovery mechanism adds bus clock cycles between PCI originated 17 O cycles to the ISA bus This delay takes place because the PCI bus is so much faster than the ISA bus This item allows you to determine the recovery time allowed for 8 bit 1 O The choice from 1to 16 CPU clocks USB Controller USB Legacy Support Select Enabled if your system contains a Universal Serial Bus USB controller and you have a USB keyboard The choice Enabled Disabled Multiple Monitor Support The choice M B First PCI First Video Memory Size Select the Video memory size The choice None 1 5M 2 5M 4 0M PEB 6530VL User s Manual 4 16 BIOS Setup Information 4 2 5 INTEGRATED PERIPHERALS FEATURES SETUP ROM PCI ISA BIOS 2A434PUD gt INTEGRATED PERIPHERALS AWARD SOFTWARE INC IDE HDD Block Mode Enabled Primary IDE Channel Master Drive PIO Mode Slave Drive PIO Mode Onboard Parallel Port Secondary IDE Channel Parallel Port Mode Master Drive PIO Mode ECP Mode Use DMA Slave Drive PIO Mode EPP Mode Select Onboard Serial Port 3 IDE Primary Master UDMA Serial Port 3 Use IRQ IDE Primary Slave UDMA Onboard Serial Port 4 IDE Secondary Master UDMA Serial Port 4 Use IRQ IDE Secondary Slave UDMA GPIO Port KBC input clock Onhoard FDC Controller Onboard Serial Port 1 Onhoard Serial Port 2 IDE HDD Block Mode This allows your hard disk
5. 3 Port 4 Connector 2 x 5 shrouded header PIN No Signal Description TX 4 RX oi Ground GN D Data Set Ready DSR Request to Send RTS 8 Clearto Send CTS 9 Ringindicator RI J13 J 8 IDE1 1DE2 Interface Connector PIN No Signal Description PIN No Signal Description RESET 2 LGround PEB 6530VL User s Manual 2 3 Hardware Configuration Setting 25 IOR 25 por CT 26 27 IOCHRDY 28 Pulidown_ _ 31 DMA ACK 31 JINTREQ 32 35 HDC CS0 38 HDC CS1 HDD Active 40 Ground _ ________ J7 ID E1 ID E2 Active LED Header PIN No Signal Description 5V 470 ohm pull up for HDD LED HDD Active LED cathode terminal J21 Compact Flash Connector PIN No Signal Description gt Signal Description GND o DS PEB 6530VL User s Manual 2 4 Hardware Configuration Setting J6 Power LED Connector Signal Description 5V 330 ohm pull up for power LED 14 16 Serial Port 1 Port 2 Connector PIN No Signal Description 6 Data Set Ready DSR 8 Cleartosend CTS SSS o Ring Indicator RI J9 FDC Interface Connector PIN No _ Signal Description PIN No Signal Description 5 Grond 6 INC _ O 7 Grond 8 Index _ _ _ _ _ 9 Ground 10 MotorENA PEB 6530VL User s Manual 2 5 Hardware Configuration Setting 2 13 USBx2 Interface Connector Signal Description USBDY D2
6. J4 Ethernet R 45 Interface Connector PIN No Signal D escription Termination to Ground RX Termination to Ground Termination to Ground ESA e J 10 Parallel Port Connector PIN No _ Signal Description PIN No Signal Description 6 Datat 19 Ground 8 Dae6 Ground 9 Daa7 Ground PEB 6530VL User s Manual 2 6 Hardware Configuration Setting J17 PS 2 Keyboard M ouse Connector Signal D escription AC Ne J1 On board VGA DSUB 15 Connector PIN No Signal D escription CON _____s e con Coo e o J5 External Speaker H eader PIN No Signal Description Speaker signal MA N C PEB 6530VL User s Manual 2 7 Hardware Configuration Setting PA GPIO Interface Connector Signal D escription PEB 6530VL User s Manual 2 8 System Installation Chapter 3 System Installation This chapter provides you with instructions on how to set up your computer system using PEB 6530VL Panel Computer Board The additional information shows you how to install Ethernet Graphic in an Operating System 3 1 Graphic Driver Installation for NS Geode GX1 XpressGRAPHICS Theon chip XPRESS Graphics is based on the GX1 CPU and the CS5530A Companion chip and this graphics controller is very cost efficient since almost no additional components are required This is achieved by using the SDRAM as frame buffer and by integrating the graphics engine and display interface in th
7. Level Edge Slot 1 Use IRQ No Auto Auto 3 4 5 6 7 9 10 11 12 14 15 Slot 2 Use IRQ No Auto Auto 3 4 5 6 7 9 10 11 12 14 15 Slot 3UseIRQ No Auto Auto 3 4 5 6 7 9 10 11 12 14 15 Slot 4UseIRQ No Auto Auto 3 4 5 6 7 9 10 11 12 14 15 PEB 6530VL User s Manual 4 6 BIOS Setup Information 4 2 1 STANDARD CMOS SETUP The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each tem ROM PCLZISA BIOS 2A434PUD gt STANDARD CMOS SETUP AWARD SOFTWARE INC Date mm dd yy gt Time hh mm 3ss gt HARD DISKS o CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Primary Slave Secondary Master Secondary Slave Drive A Drive B Base Menory 640K 8 x Extended Menory 257024K rio E Other Menory 384K Total Henory 258048K ESC Quit TESE Select Item PU PD Modify Fi Help CShift gt F2 Change Color Date mm dd yy The date format is lt day gt lt date gt lt month gt lt year gt Press lt F3 gt to show the calendar Day The day from Sun to Sat determined by the BIOS and is display only The date from 1 to 31 or the maximum allowed in the month The month Jan through Dec The year from 1900 through 2099 Time hh mm ss The ti
8. controller to use the fast block mode to transfer data to and from your hard disk drive HDD Enabled IDE controller uses block mode Disabled IDE controller uses standard mode Primary Secondary IDE Channel Y ou may separately disablethe primary second channel on an IDE interface installed in aPCI expansion slot The choice Enabled Disabled IDE Primary Secondary M aster Slave PIO Mode The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes O through 4 provide successively increased performance In Auto mode the sy stem automatically determines the best mode for each device The choice Auto Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 IDE Primary Secondary M aster Slave UDMA This item allows you to enable disable the IDE Primary Secondary Master Slave UDMA mode The choice Auto Disabled PEB 6530VL User s Manual 4 17 BIOS Setup Information KBC Input Clock This item allows you to select the KBC input clock frequency The choice 6M Hz 8M Hz 12M Hz 16MHz Onboard FDD Controller This should be enabled if your system has a floppy disk drive FDD installed on the system board and you wish to use it Even when so equipped if you add a higher performance controller you will need to disable this feature The choice Enabled Disabled Onboard Serial Port 1 Port 2 This item allows you to determine access
9. disk drive then floppy disk drive A C SCSI System will first search for floppy disk drive then hard disk drive CDROM C A System will first search for CDROM drive then hard disk drive and the next is floppy disk drive C CDROM A System will first search for hard disk drive then CDROM drive and the next is floppy disk drive AJ Conly LS120 C Swap Floppy Drive This item allows you to determine whether enable the swap floppy drive or not The choice Enabled Disabled Boot Up Floppy Seek During POST BIOS will determine if the floppy disk drive installed is 40 or 80 tracks 360K type is 40 tracks while 760K 1 2M and 1 44M are all 80 tracks Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks Note that BIOS cannot tell from 720K 1 2M or 1 44M drive type as they are all 80 tracks drive installed is 360K Disabled BIOS will not search for the type of floppy disk drive by track number Note that there will not be any warning message if the PEB 6530VL User s Manual 4 11 BIOS Setup Information Boot Up NumLock Status This allows you to determine the default state of the numeric keypad By default the sy stem boots up with NumLock on On O Keypad is number keys Keypad is arrow keys I Boot Up System Speed Selects the default system speed the normal operating speed at power up High Set the speed to high Low Set the speed to low Gate A 20 Option This entry all
10. installed in the system The value of the base memory is typically 512K for systems with 512K memory installed on the SBC or 640K for systems with 640K or more memory installed on the SBC Extended Memory The BIOS determines how much extended memory is present during the POST This isthe amount of memory located above 1MBin the CPU s memory address map PEB 6530VL User s Manual 4 9 BIOS Setup Information Other M emory This refers to the memory located in the 640K to 1024K address space This is memory that can be used for different applications DOS uses this area to load device drivers in an effort to keep as much base memory free for application programs The BIOS is the most frequent user of this RAM area since this is where it shadows RAM 4 2 2 BIOS FEATURES SETUP This section allows you to configure your system for basic operation You have the opportunity to select the system s default speed boot up sequence keyboard operation shadowing and security ROM PCIZISA BIOS C2A434PUD BIOS FEATURES SETUP AWARD SOFTWARE INC Virus Warning Disable Video BIOS Shadow CPU Internal Cache z C8BEB CEBFFF Shadow CC BG CFFFF Shadow Quick Power On Self Test DBBEB D3FFF Shadow Boot Sequence z D4066 D7FFF Shadow Swap y py Drive D8BBB DBFFF Shadow Boot gt pr Seek DC BG DFFFF Shadow Boot uD NumLock Status z Cyrix 6x86 MII CPUID Boot Up System Speed Gate A28 Option Memory Parity Check Typematic Rate Setting Typem
11. power management mode nor awaken it e RQ1 Keyboard e IRQ3 COM 2 e IRQ4 COM1 e IRQ5 LPT 2 e IRQ6 Floppy Disk e IRQ7 LPT 1 e RQ9 IRQ2 Redir e RQ10 Reserved e RQ11 Reserved e RQ12 PS 2 Mouse e RQ13 Coprocessor e RQ14 Hard Disk e RQ15 Reserved 4 2 7 PNP PCI CONFIGURATION SETUP This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows 17 O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings ROM PCI ISA BIOS 24434PUD gt PNP PCI CONFIGURATION AVARD SOFTUARE INC PNP OS Installed No PCI IRQ Actived By Resources Controlled By Reset Configuration Data Slot 1 Use IRQ Ho Auto Slot 2 Use TIRO Ho Auto Slot 3 Use TIRO Ho Auto Slot 4 Use TIRO Ho Auto PCI IRQ Actived By Level gt Quit Hi gt e Select Item Help PU PD Modify Old Values CShift gt F2 Color Load BIOS Defaults Load Setup Defaults PEB 6530VL User s Manual 4 21 BIOS Setup Information PNP OS Installed This determines whether the PnP OS is installed or not Choices are Yes and No Resource Controlled By The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug a
12. 1 5 Introduction 1 3 7 Ethernet The Ethernet interfaces are based on one Intel 82559 Ethernet controller which support both 100M bit as well as IOM bit Base T interface The Ethernet controllers are attached to the PCI bus and use PCI bus mastering for data transfer The CPU is thereby not loaded during the actual data transfer 1 3 8 Winbond W83977F A 8 W83977ATF AW The Winbond W83977F A Super I O chip provides most input output interfaces of the system asthefollowing COM 1 2 Operates in RS 232 mode through a charge pump driver Only 5V supply is required COM 3 8 4 A RS422 RS485 driver is used whereby RS 422 and RS 485 are provided Selection of the mode is made by hardware jumper Driver uses charge pumps whereby only 5V is required u LPT Support for SPP EPP and ECP modes Floppy interface u Keyboard interface a PS 2 Mouse interface Provision of buffered ISA data bus for BIOS denoted XDBus NVRAM with battery backup for BIOS configuration and real time clock a Watchdog timer 1 3 9 Compact Flash Interface A Compact Flash typell connector is connected to the secondary IDE controller The Compact Flash storage card is IDE compatible It is an ideal replacement for standard IDE hard drives The solid state design offers no seek errors even under extreme shock and vibration conditions The Compact Flash storage card is extremely small and highly suitable for rugged environments thus providing an excelle
13. Hard Disk Type STANDARD CMOS SAETUP This setup page includes all the items in a standard AT compatible BIOS such as Time Date Hard Disk Type BIOS FEATURES SETUP This setup page includes all the items of Award special enhanced features such as Virus Protection Boot Sequence PASSWORD SETTING Change set or disable password It allows you to limit access to the system and Setup or just to Setup CHIPSET FEATURES SETUP This setup page includes all the items of chipset special features such as AT Clock DRAM timings PEB 6530VL User s Manual 4 2 BIOS Setup Information POWER MANAGEMENT SETUP This entry only appears if your system supports Power Management Green PC standards You can set up time period for power saving mode such as Sleep timer Suspend timer PNP PCI CONFIGURATION This entry appears if your system supports PNP PCI such as IRQ Settings Latency Timers LOAD BIOS DEFAULTS The default settings load BIOS Defaults except Standard CMOS SETUP LOAD SETUP DEFAULTS The chipset defaults are settings which provide for maximum system performance While Award has designed the custom BIOS to maximize performance the manufacturer has the right to change these defaults to meet their needs INTEGRATED PERIPHERALS This section page includes all the items of IDE hard drive and Programmed Input Output features such as On board I O IRQ DMA Assignment IDEHDD AUTO DETECTION Au
14. Interface for bi directional parallel port x 1 Supports SPP ECP and EPP modes e Serial port Two internal header supports RS 232 x 2 two internal header supports RS 422 485 x 2 Ports can be configured as COM1 COM2 COM3 COM4 or disabled individually 16C550 equivalent e KB M ouse connector Internal header PS2 Keyboard Mouse connector x 1 e USB connectors One 5 x 2 header on board supports dual USB ports or external down link 2 connector e Watchdog Timer Super watchdog timer from 0 5 to 64 sec by hardware count amp software trigger o DMA 7 DMA channels 8237 equivalent e Interrupt 15 interrupt levels 8259 equivalent e Power management I O peripheral devices support power saving and doze standby suspend modes APM 1 2 compliant PEB 6530VL User s Manual 1 2 Introduction e Display Chipset NS Geode CS5530A Display memory Shared display memory up to 4MB e Display type Supports non interlaced CRT e Resolution Up to 1024x768x16 bpp e Fast Ethernet Chipset One Intel 82559 PCI bus Ethernet controllers on board e Ethernet interface PCI 100 10 Mbps IEEE 802 3U compatible Remote Boot ROM For diskless system e SSD interface One CF socket supports Typell Compact Flash Card Support 8 320M B Compact flash Expansion interface One PICMG Golden Finger Connectors on the bracket VGA DB 15 Ethernet RJ 45 PS 2 Keyboard Mouse and USB for Specific Power connectors From PICMG G
15. PEB 6530VL Embedded System Board User s Manual P N B8980920 Version 1 0 Copyright Portwell Inc 2002 All rights reserved All other brand names are registered trademarks of their respective owners Preface Table of Contents How to Use This Manual Chapter 1 Tn 1 1 11 Check Lit iii naaa din 11 12 Product Specifications aseti 4 064 be ation oN e Geet d 1 2 12 1 Mechanical and Environmental ocociciccicicinnnnnnnncccnnnncrrrcncnnr rra 13 1 2 2 Mechanical Drawing cocine 1 4 13 System Architecture cui d sd n einen eee aie 1 4 13 1 GPU GX Tand S5530A nuse nd Ane dd di red de dened el a dene 1 4 13 2 XPRESS Grapes wink ening ii a ae aA ATL Ratha nia 15 13 3 PERBUSK ne ett e e terete Neat 1 5 13 4 SDRAM Interfaces s ndves ee dendi aureus er 15 13 5 IDE Interface tn A ie Meo ee 1 5 13 6 USB irvine sh a a aie aie fe ea 15 1 3 7 EMM saith a ata sateen a a ale eNA ETEEN 16 13 8 Winbond W83977F A W83977ATF AW aauuuaaacaca cave veze zezez ez er ee tee e rere re reze zer eren 16 13 9 Compact Flash INTE AQE u uv ae eee vere re reze re zeze eee e rere e nene e netet eter e zez 1 6 Chapter 2 Hardware Configuration Setting cccesccesseeeseeeeeeeeeesseesesneeeeseeeeseaesnseeeeees 2 1 2 1 Jumper SEEING duarve parit vez ve is odie dow aie AAA udh to 2 1 2 2 CON TELE 2 3 Chapter 3 System InstallatioN i cociociocitacoioiitornccndociniajoticenigeoecdndn s n n vddos ve de s ecen
16. RQ10 IRQ3 4 5 6 7 11 Onboard Parallel Port 3781 IRQ7 3781 IRQ7 2781 IRQS 3BC IRQ7 Disabled Parallel Port Mode SPP SPP ECP EPP ECP EPP ECP ModeUseDMA 3 3 1 EPP Mode Select EPP1 9 EPP1 9 EPP1 7 GPIO Port 200 202H 200 202H 300 302H 400 402H Disabled e Power M anagement Setup Table BIOS Setup Items BIOS Default Setup Default Other Options Power Management Disabled Disabled Min Saving Max Saving User Defined Doze Mode Disabled Disabled 1 2 4 8 10 12 16 Sec Standby Mode Disabled Disabled 1 2 3 4 5 6 8 10 12 15 16 20 40 60 Min HDD Power Down Disabled Disabled 1 2 3 4 5 6 8 10 12 15 16 20 40 60 Min IRQ1 Keyboard ON ON OFF IRQ3 COM 2 OFF OFF ON IRQ4 COM 1 OFF OFF ON IRQ5 LPT 2 OFF OFF ON IRQ6 Floppy Disk OFF OFF ON PEB 6530VL User s Manual 4 5 BIOS Setup Information IRQ7 LPT 1 OFF OFF ON IRQ9 IRQ2 Redir OFF OFF ON IRQ10 Reserved OFF OFF ON IRQ11 Reserved OFF OFF ON IRQ12 PS 2 Mouse OFF OFF ON IRQ13 Coprocessor OFF OFF ON IRQ14 Hard Disk OFF OFF ON IRQ15 Reserved OFF OFF ON e PNP PCI Configuration Setup Table BIOS Setup Items BIOS Default Setup Default Other Options PnP OS Installed No No Yes Resource Controlled By Auto Auto Manual Reset Configuration Data Disabled Disabled Enabled PCI IRQ Activated By Level
17. atic Rate Chars Sec gt Typenatic Delay lt Msec gt Security Option PCI UGA Palette Snoop z E i tire Select Item OS Select For DRAM gt 6 4MB z PU PD Modify Report No FDD For WIN 95 r Old Values lt Shift F2 Color Load BIOS Defaults Load Setup Defaults Virus Warning When this item is Enabled the A ward BIOS will monitor the boot sector and partition table of the hard disk drive for any attempt at modification If an attempt is made the BIOS will halt the system and the following error message will appear Afterwards if necessary you will be able to run an anti virus program to locate and remove the problem before any damage is done WARNING Disk boot sector is to be modified Type Y to accept write or N to abort write Award Software Inc PEB 6530VL User s Manual 4 10 BIOS Setup Information CPU Internal Cache This category speeds up memory access However it depends on CPU chipset design The default value is en able Enabled Enable cache Disabled Disable cache Quick Power On Self Test This category speeds up Power On Self Test POST after you power up the computer If it is set to Enable BIOS will shorten or skip some check items during POST Enabled Enable quick POST Disabled Normal POST Boot Sequence This category determines which drive to search first for the disk operating system i e DOS Default value isA C SCSI C A SCSI System will first search for hard
18. ation 3 2 IDE Interface A primary as well as a secondary IDE controller is provided by the CS5530A companion chip which supports Ultra DMA mode and PCI bus mastering for the data transfer Access to these controllers is provided by a standard IDE 40 pin connector and a Compact Flash type II connector on the solder side of this board 3 3 PCI Bus The PCI bus on the board is provided by the GX1 CPU and will always run at 33M Hz The GX1 CPU provides support for up to three bus masters These bus master signals are used by the CS5530A and one Intel 82559 Ethernet controller 3 4 SDRAM Interface This board uses SODIMM 3 3V PC 100 SDRAM modules are recommended to use 3 5 USB The USB interface provides two USB channels that are controlled by the CS5530A The signals are provided by means of a 5 x 2 header2 or by an optional USB bracket adapter or down link 2 connector 3 6 Compact Flash Interface A Compact Flash type ll connector is connected to the secondary IDE controller The Compact Flash storage card is IDE compatible It is an ideal replacement for standard IDE hard drives The solid state design offers no seek errors even under extreme shock and vibration conditions The Compact Flash storage card is extremely small and highly suitablefor rugged environments thus providing an excellent solution for mobile applications with space limitations It is fully compatible with all consumer applications designed for data storage PC
19. card PDA and Smart Cellular Phones allowing simple use for the end user The Compact Flash storage card is O S independent thus offering an optimal solution for embedded systems operating in non standard computing environments The Compact Flash storage card is IDE compatible and offers various capacities PEB 6530VL User s Manual 3 2 System Installation 3 7 VVinbond W83977F A 8 W83977ATF AW The Winbond W83977F A Super I O chip provides most input output interfaces of the system asthefollowing e COM 12 Operates in RS 232 mode through a charge pump driver Only 5V supply is required 6 COM 34 A RS422 RS485 driver is used whereby RS 422 and RS 485 are provided Selection of the mode is made by hardware jumper adjusting Driver uses charge pumps whereby only 5V is required LPT Support for SPP EPP and ECP modes Floppy interface Keyboard interface PS 2 Mouse interface NVRAM with battery backup for BIOS configuration and real time clock Watchdog timer PEB 6530VL User s Manual 3 3 BIOS Setup Information Chapter 4 BIOS Setup Information 4 1 Starting Setup The Award BIOS is immediately activated when you first power on the computer The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it When it finishes the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system While
20. e GX1 CPU and the CS5530A companion chip This controller provides a CRT Driver Support PEB 6530VL provides one CD Title to support on board VGA device drivers in various operating systems Before installing the device driver please see the reference files in each sub directory If you have problems to install drivers directly from CDROM please copy the files into your hard drive before you proceed with the driver installation e VGA This driver supports VVindovvs 4 0 Windows 9X N ote For more detailed installation steps please refer to our installation guide file Ethernet The Ethernet interfaces are based on one Intel 82559 Ethernet controller which support both 100M bit as well as IOM bit Base T interface The Ethernet controllers are attached to the PCI bus and use PCI bus mastering for data transfer The CPU is thereby not loaded during the actual data transfer Driver Support PEB 6530VL provides one CD Title to support on board Ethernet device drivers in various operating systems Before installing the device driver please see the reference files in each sub directory If you have problems to install drivers directly from CDROM please copy the files into your hard drive before you proceed with the driver installation e Ethernet This driver supports Windows 4 0 VVindovvs 9X N ote For more detailed installation steps please refer to our installation guide file PEB 6530VL User s Manual 3 1 System Install
21. e installed 1 1 Check List The PEB 6530VL package includes the following basic items accompany with this manual 1PEB 6530VL All in One NS Geode GX1 Computing Module 1CD ROM contains the followings User s Manual this manual in PDF file Ethernet driver and utilities VGA drivers and utilities Latest BIOS as of the CD ROM was made a Cable set includes the followings 1 Bracket with one PS 2 K B mouse port cable 1PS 2 Keyboard and mouse Y cable 10 pin Mini DIN 11DE HDD cable 40 pin pitch 2 54mm 1FDD cable 34 pin pitch 2 54mm lbracket with one Printer port cable 26 pin pitch 2 0mm 2bracket with two serial port cable 10 pin pitch 2 54mm 4pinto 4 pin ATX control cable If any of these items is damaged or missed please contact your vendor and save all packing materials for future replacement and maintenance PEB 6530VL User s Manual 1 1 Introduction 1 2 Product Specifications e Main processor Onboard NS Geode GX1 300M Hz BGA package e BIOS Award 256KB Flash BIOS e Chipset N S Geode CS5530A e 1J0 Chipset Winbond W83977F A Winbond W83977ATF AW Memory On board two 144 pin SODIMM socket supports up to 512 Mbytes SDRAM Enhanced IDE Supports two IDE devices Supports Ultra DMA 33 mode with data transfer rate up to 33M B sec e FDD interface Supports up to one floppy disk drives 5 25 360KB and 1 2MB and or 3 5 720KB 1 44M B and 2 88M B e Parallel port
22. econdary controller and a Compact Flash connector on the secondary controller PEB 6530VL User s Manual 1 4 Introduction 1 3 2 XPRESS Graphics The XPRESS Graphics is based on the GX1 CPU and the CS5530A Companion chip and this graphics controller is very cost efficient since almost no additional components are required This is achieved by using the SDRAM as frame buffer and by integrating the graphics engine and display interface in the GX1 CPU and the CS5530A companion chip This controller provides a CRT interface 1 3 3 PCI Bus The PCI bus on the board is provided by the GX1 CPU and will always run at 33M Hz The GX1 CPU provides support for up to three bus masters These bus master signals are used by the CS5530A and the Intel 82559 Ethernet controller 1 3 4 SDRAM Interface This board uses SODIMM up to 512MB 3 3V PC 100 SDRAM modules are recommended to use 1 3 5 IDE Interface A primary as well as a secondary IDE controller is provided by the CS5530A companion chip which supports Ultra DMA mode and PCI bus mastering for the data transfer Access to these controllers is provided by a standard IDE 40 pin connector and a Compact Flash type II connector on the solder side of this board 1 3 6 USB The USB interface provides two USB channels that are controlled by the CS5530A The signals are provided two 5 pin header that can be connected to standard USB bracket adapter or use down link connector PEB 6530VL User s Manual
23. ed Cyrix 6x86 M II CPUID The choice Enabled Disabled 4 2 3 PASSWORD SETTING Password just can only enter but do not have the right to change the options of the setup menus When you select this function the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type the password up to eight characters in length and press lt Enter gt The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press lt Enter gt You may also press lt Esc gt to abort the selection and not enter a password PEB 6530VL User s Manual 4 14 BIOS Setup Information To disable a password just press lt Enter gt when you are prompted to enter the password A message will confirm the password will be disabled Oncethe password is disabled the system will boot and you can enter Setup fredy PASSWORD DISABLED When a password has been enabled you will be prompted to enter it every time you try to enter Setup This prevents an unauthorized person from changing any part of your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time your system s rebooted This would prevent unauthorized use of your computer Y ou determine when the password is required within the BIOS Features Setup Menu and its Security option If
24. es jumpers headers and connectors locations Users may find useful information related to hardware settings in this chapter The default settings are indicated with a start sign Ar 2 1 Jumper Setting For users to customize PEB 6530V L s features In the following sections Short means covering a jumper cap over jumper pins Open or N C Not Connected means removing a jumper cap from jumper pins Open Closed Closed 2 3 za ds Open Closed Closed 2 3 NE ze A ca E o me T at O IF H Jp1 BZ1 BIOS CS5530A Figure 2 1 PEB 6530VL Jumper and Connector Locations PEB 6530VL User s Manual 2 1 Hardware Configuration Setting RTC CMOS Clear Jumper Setting P1 Process Selection Normal Operation Clear CMOS Contents WATCH DOG TIMER Jumper Setting JP5 JP5 1 2 Processor Selection NC Watch DOG Timer Enabled Watch DOG Timer Disabled 10 Port Location 533 033 543 343 JP5 5 6 JP57 8 JP59 10 Twd On board Ethernet enable disable JP3 JP3 Processor Selection On board Ethernet Enabled x On board Ethernet Disabled On board COM port setting Processor Selection RS 422 FOR COM3 x RS 485 FOR COM3 RS 422 FOR COMA x RS 485 FOR COM4 PEB 6530VL User s Manual 2 2 Hardware Configuration Setting 2 2 Connectors JP2 Reset Header PIN No Signal Description 1 Reset 2 Ground JP6 Power On Header PIN No Signal Description 1181 19 Serial Port
25. m you get a confirmation dialog box with a message similar to Load Optimized Defaults Y N N Pressing Y loads the default values that are factory settings for optimal performance system operations IDE HDD AUTO DETECTION SAVE amp EXIT SETUP Pressing lt Enter gt on this item asks for confirmation Save to CMOS and EXIT Y N Y Pressing Y stores the selections made in the menus in CMOS a special section of memory that stays on after you turn your system off The next time you boot your computer the BIOS configures your system according to the Setup selections stored in CMOS After saving the values the system is restarted again EXIT WITHOUT SAVING Pressing lt Enter gt on this item asks for confirmation Quit without saving Y N Y This allows you to exit Setup without storing in CMOS any change The previous selections remain in effect This exits the Setup utility and restarts your computer PEB 6530VL User s Manual 4 23
26. me format is lt hour gt lt minute gt lt second gt The time is calculated based on the 24 hour military time clock For example 1 p m is 13 00 00 Primary M aster Primary Slave Secondary M aster Secondary Slave The categories identify the types of 2 channels that have been installed in the computer The choice Auto User None PEB 6530VL User s Manual 4 7 BIOS Setup Information Press PgUp or PgDn to select a numbered hard disk type or type the number and press lt Enter gt Note that the specifications of your drive must match with the drive table The hard disk will not work properly if you enter improper information for this category If your hard disk drive type is not matched or listed you can use Type User to define your own drive type manually If you select Type User you will need to know the information listed below Enter the information directly from the keyboard and press lt Enter gt This information should be included in the documentation from your hard disk vendor or the system manufacturer If the controller of HDD interface is ESDI the selection shall be Auto If you select Type Auto BIOS will Auto Detect the HDD amp CD ROM Drive at the POST stage and showing the IDE for HDD amp CD ROM Drive If a hard disk has not been installed select NONE and press lt Enter gt DriveA Type DriveB Type The category identifies the types of floppy disk drive A or drive B that have been
27. nd Play compatible devices However this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows 95 Choices are Auto and M anual Reset Configuration Data This item allows you to determine reset the configuration data or not The choice Enabled Disabled Slot 1UseIRQ No The choice Auto 3 4 5 6 7 9 10 11 12 14 15 Slot 2UseIRQ No The choice Auto 3 4 5 6 7 9 10 11 12 14 15 Slot 3 UseIRQ No The choice Auto 3 4 5 6 7 9 10 11 12 14 15 Slot 4UseIRQ No The choice Auto 3 4 5 6 7 9 10 11 12 14 15 IRQ X DMA X Assigned To This item allows you to determine the IRQ DMA assigned to the ISA bus and is not available to any PCI slot The choice Legacy ISA PCI ISA PnP PCI IRQ Activated By This sets the method by which the PCI bus recognizes that an IRQ service is being requested by a device Under all circumstances you should retain the default configuration unless advised otherwise by your system s manufacturer The choice Level Edge PEB 6530VL User s Manual 4 22 BIOS Setup Information LOAD BIOS DEFAULTS When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load Fail Safe Defaults Y N 2 N Pressing Y loads the BIOS default values for the most stable minimal performance system operations LOAD SETUP DEFAULTS When you press lt Enter gt on this ite
28. nt solution for mobile applications with space limitations It is fully compatible with all consumer applications designed for data storage PC card PDA and Smart Cellular Phones allowing simple use for the end user The Compact Flash storage card is O S independent thus offering an optimal solution for embedded systems operating in non standard computing environments The Compact Flash storage card is IDE compatible and offers various capacities The following block diagram shows the architecture and main components of PEB 6530VL PEB 6530VL User s Manual 1 6 Introduction SODIMM SDRAM 100 10 BASE pea RI 45 Processor Clocks Intel nte Serial Packet p 82559 Coms PCI Interface RGB Ports Sompact Flash re PCI Bus Ultra IDE pet RS 232x2 USB 2 Ports jt Graphics Data LPT Geode Video Data Minbond CS5530 ee W83977F A KBD T O Companion 48519 py Analog RGB Mouse W83977ATF AW BIOS Watchdog CRT Timer l 14318 E GPIO ISA Bus Figure 1 1 PEB 6530V L System Block Diagram The two key components on board are the NS Geode GX1 CPU and the CS5530A companion chip These two devices provide the ISA and PCI bus to which all the major components are attached PEB 6530VL User s Manual 1 7 Hardware Configuration Setting Chapter 2 Hardware Configuration Setting This chapter indicat
29. olden Finger 1 2 1 Mechanical and Environmental Power supply voltage 12V 11 4V to 12 6V Typical power requirement 5V 1 66A w GX1300MHz Operating temperature 32 to 122 F Oto 50 C Board size 121 5mm x 185mm PEB 6530VL User s Manual 1 3 Introduction 1 2 2 Mechanical Drawing 185 3 94 THRU 35 178 al sf i ES E 8 gi T BI MIA A LN LI 5 05 alg 8 19 E El 63 75 _ 15 49 2 THRU A 6 E 35 85 5 05 41 82 S 1 3 System Architecture 1 3 1 CPU GX1 and CS5530A The NS Geode GX1 along with the CS5530A companion chip provide the basic functionality and buses of the system Interface to SDRAM 64 bit data bus PC 100 compliant SDRAM must be used PCI interface provided by GX1 CPU PCI to ISA Bridge provided by CS5530A VGA controller with video memory shared with system memory UMA The image data is transferred to the companion chip by means of Pixd bus CRT interface Data provided by the Pixd and Video interface from the CPU Video interface from GX1 to the CS5530A This data stream is buffered and multiplexed with the Pixd bus for windowed video viewing This interface may assist the processor in connection motion picture decoding USB integrated in the CS5530A IDE interface support Ultra DMA Tow connectors are provided A 40 pin pitch 2 54mm standard IDE interface on the primary and s
30. onboard serial port 1 port 2 controller with which 14 O address The choice 3F8 IRQA 2F8 IRQ3 3E8 IRQA 2E8 IRQ3 Disabled Auto Onboard Serial Port3 Port4 This item allows you to determine access onboard serial port 3 port 4 controller with which 14 O address The choice 3F8 2F8 3E8 2E8 Disabled IRQ3 IRQ4 IRQ5 IRQ IRQ7 IRQ9 IRQ10 IRQ11 Onboard Parallel Port Select a logical LPT port name and matching address for the physical parallel printer port The choice 378 IRQ7 278 IRQ5 3BC IRQ7 Disabled Parallel Port M ode Select an operating mode for the onboard parallel port Select Compatible or Extended unless you are certain both your hardware and software support EPP or ECP mode The choice SPP EPP ECP ECP EPP ECP ModeUseDMA Selecta DMA channel for the port The choice 3 1 PEB 6530VL User s Manual 4 18 BIOS Setup Information EPP M ode Select Select EPP porttype 1 7 or 1 9 The choice EPP1 7 EPP1 9 GPIO Port Select GPIO port 1 O port address GPI port address GPO port address The choice 200 202H 300 302H 400 402H Disabled 4 2 6 POWER MANAGEMENT SETUP The Power Management Setup allows you to configure you system to most effectively save energy while operating in a manner consistent with your own style of computer use ROM PCI ISA BIOS 2A434PUD gt POWER MANAGEMENT SETUP AWARD SOFTWARE INC Power Management Disabled lt Ke yBoard gt lt COM 2 g
31. ouncil Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive 897 336 EEC The equipment was evaluated and passed the test the following standards were applied EMC EN 55022 1994 A 1 1995 Class A EN 50082 2 1991 EN 61000 4 2 1995 EN 61000 4 3 1996 EN 61000 4 4 1995 EN 61000 3 2 1995 EN 61000 3 3 1995 The follovving manufacturer is responsible for this dedaration Portwell Inc Company Name 3F No 88 Sec 1 Nei Hu Rd Taipei Taiwan R O C Company Address Taipei R O C Place Date Legal Signature of Authorized Person Introduction Chapter 1 Introduction This manual describes in detail the Portwell PEB 6530VL Embedded System Board This manual aims to provide all necessary information to users who may interest in using all PEB 6530VL s functions The PEB 6530VL is a low power ISA Bus half sized SBC that equips with low power NS Geode GX1 processor VGA and single PCI bus Ethernet interfaces This model is very compact with extensibility For an embedded system Watch Dog Timer is also one standard feature It helps to free the system from undesired hanging without human interface This is unique for many Embedded System applications Other impressive features include the a Compact Flash socket for Compact Flash storage card four serial ports one parallel port and two 144 pin SODIMM sockets allowing for up to 384M B of SDRAM to b
32. ows you to select how the gate A 20 is handled The gate A20 is a device used to address memory above 1 Mbytes Initially the gate A20 was handled via a pin on the keyboard Today while keyboards still provide this support it is more common and much faster for the system chipset to provide support for gate A 20 keyboard Fast chipset M emory Parity Check The choice Enabled Disabled Typematic Rate Setting This determines if the typematic rate is to be used When disabled continually holding down a key on your keyboard will generate only one instance In other words the BIOS will only report that the key is down When the typematic rate is enabled the BIOS will report as before but it will then wait a moment and if the key is still down it will begin the report that the key has been depressed repeatedly For example you would use such a feature to accelerate cursor movements with the arrow keys Enabled Enable typematic rate Disabled Disable typematic rate PEB 6530VL User s Manual 4 12 BIOS Setup Information Typematic Rate Chars Sec When the typematic rate is enabled this selection allows you select the rate at which the keys are accelerated Typematic Delay M sec When the typematic rate is enabled this selection allows you to select the delay between when the key was first depressed and when the acceleration begins Security O ption This category allows you to limit access to the system and Se
33. pecifications and basic system architecture for this mode of single board computer Chapter 2 H ardware Configuration Setting This chapter shows the definitions and locations of Jumpers and Connectors that you can easily configure your system Chapter 3 System Installation This chapter describes how to properly mount the CPU and main memory Solid State Flash disk or optional flat panel display interface module to get a safe installation and give you a programming guide of Watch Dog Timer function Besides it will introduce and show you the driver installation procedure about Graphics Controller Chapter 4 BIOS Setup Information This chapter specifies the meaning of each setup parameters and how to get advanced BIOS performance and update new BIOS In addition POST checkpoint list will give you a guide of trouble shooting The content of this manual and EC declaration document is subject to change without prior notice These changes will be incorporated in new editions of the document Portwell may make supplement or change in the products described in this document at any time Updates to this manual technical clarification and answers to frequently asked questions will be shown on the following web site http www portwell com tw Preface EC Declaration of Conformity To Be Added For the following equipment Product Name Model Name Trade Name is herewith confirmed to comply with the requirements set out in the C
34. t x PM Timers nx lt COM 1 gt Doze Mode Disabled lt LPT 2 Standby Mode Disabled Floppy Disk gt HDD Power Down Disabled lt LPT 1 lt IRQ2 Redir gt lt Reserved gt CReserved gt lt PS 2 Mouse lt Coprocessor Hard Disk gt lt Reserved gt Quit Tiz Select Item Help PU PD Modify Old Values lt Shift gt F2 Color Load BIOS Defaults Load Setup Defaults Power M anagement This category allows you to select the type or degree of power saving and is directly related to the following modes 1 Doze Mode 2 Standby Mode 3 HDD Power Down There are four selections for Power Management three of which have fixed mode settings PEB 6530VL User s Manual 4 19 BIOS Setup Information default Min Saving Minimum power management Doze Mode 16 Sec Standby Mode 60Min and HDD Power Down 60 Min M ax Saving Maximum power management ONLY AVAILABLE FOR SL CPU s Doze Mode 4 Sec Standby Mode 1 min and HDD Power Down 1 Min User Define Allows you to set each mode individually When not disabled each of the ranges are from 1 Sec to 16 Sec except for HDD Power Down and Standby Mode which ranges from 1 Min to 60 Min and disable Doze Mode When enabled and after the set time of system nactivity the CPU clock will run at slower speed while all other devices still operate at full speed The choice 1 Sec 2 Sec 4 Sec 8 Sec 10 Sec 12 Sec 16 Sec Disabled
35. t s 3 1 3 1 Graphic Driver installation for NS Geode GX1 XpressGRA PAC Su u uuuu cuan 3 1 3 2 IDE interface enis A AAA dt At e 3 2 3 3 PEDUS ee A te E Mua et 3 2 3 4 SDRAM Interface cuan iaa racial 3 2 3 5 USB iia 3 2 3 6 Compact Flash interface mc vonon memece sec ec ev ee er ere rere e ere rr 3 2 3 7 Winbond W83977F A W83977A T FA NV 0 uua anon nenen enen e eneve vetevete zezez er eee ete te zeze zezez z er n 3 3 Chapter 4 BIOS Setup Information an uanana nana ann ao nene ne rene ne nene se te tere tet s eee sete tere tet s e nete mene set 4 1 4 1 Starbing S O e ai tats 4 1 4 2 Main Men idad 4 2 4 2 1 STANDARD E MOSSETU P sii ns Ss A Se 4 7 4 2 2 BIOS FEATURES SETU P cc cave ra 4 10 4 2 3 PASSVVORD SETITIN Go ica ad 4 14 4 2 4 CHIPSET FEATURES SETUP icon 4 15 4 2 5 INTEGRATED PERIPHERALS FEATURES SET U Pa uu una cc veze cen e ec 4 17 4 2 6 POWER MANAGEMENT SET U Po uu nana nane nc orare ne ere re reze zee rere ne ronca 4 19 4 2 7 PNP PCI CONFIGURATION SETUP mana naanocec eseve sive eee nene nene nenen eses seen 421 Preface How to Use This Manual The manual describes hovv to configure your PEB 6530VL system to meet various operating requirements It is divided into four chapters with each chapter addressing a basic concept and operation of Embedded Board Computer Chapter 1 Introduction This chapter presents what you have in the inside of box and give you an overview of the product s
36. the BIOS is in control the Setup program can be activated in one of two ways By pressing lt Del gt immediately after switching the system on or By pressing the lt Del gt key when the following message appears briefly at the bottom of the screen during the POST Power On Self Test Press DEL to enter SETUP If the message disappears before you respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing lt Ctrl gt lt Alt gt and lt Delete gt keys If you do not press the keys at the correct time and the sy stem does not boot an error message will be displayed and you will again be asked to Press F1 To Continue DEL to enter SETUP PEB 6530VL User s Manual 4 1 BIOS Setup Information 4 2 Main Menu Once you enter the Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions and two exit choices Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu The main menu includes the following main setup categories Recall that some systems may not include al entries ROM PCIZISA BIOS lt 2A434PUD gt TUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP Esc Quit LU S da Select Item Fi Save amp Exit Setup lt Shift gt F2 Change Color Time Date
37. the Security option is set to System the password will be required both at boot and at entry to Setup If set to Setup prompting only occurs when trying to enter Setup 4 2 4 CHIPSET FEATURES SETUP ROM PCIZISA BIOS 2A434PUD gt CHIPSET FEATURES SETUP AWARD SOFTWARE INC SDRAM CAS latency Time ee SDRAM Clock Ratio Div By 16 bit 1 0 Recovery lt CLK gt 8 bit 1 0 Recovery lt CLK gt USB Controller USB Legacy Support Multiple Monitor Support Video Memory Size gt Quit Ti gt e Select Item Help PU PD Modify Old Values lt Shift gt F2 Color z Load BIOS Defaults Load Setup Defaults ADVANCED OPTIONS The parameters in this screen are for system designers service personnel and technically competent users only Do not reset these values unless you understand the consequences of your changes PEB 6530VL User s Manual 4 15 BIOS Setup Information SDRAM CAS latency Time When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing Do not reset this field from the default value specified by the system designer The choice Auto 2T 3T SDRAM Clock Ratio Div By This item allows user to set the DRAM timing The choice 3 4 16 bit 170 Recovery CLK The I O recovery mechanism adds bus clock cycles between PCI originated 17 O cycles to the ISA bus This delay takes place because the PCI bus is so much faster than the ISA bus
38. tomatically detect and configure hard disk parameters The Award BIOS includes this ability in the event you are uncertain of your hard disk s parameters such as Auto Configure HDD Sector Cylinder Head SAVE EXIT SETUP Save Data to CMOS and Exit SETUP EXIT WITHOUT SAVE Abandon all Data and Exit SETUP PEB 6530VL User s Manual 4 3 BIOS Setup Information Standard CMOS Setup Reference Table This setup reference table includes all the BIOS Setup and Other options setting in each BIOS setup item It is very easy to cross reference If you want to go details you can directly refer to item description in sub section BIOS Features Setups Table BIOS Setup Items BIOS Default Setup Default Other Options Virus Warning Disabled Disabled Enabled CPU internal Cache Enabled Enabled Disabled Quick Power On Self Test Disabled Enabled Boot Sequence A C SCSI A C SCSI CD ROM SCSI LS120 and Others Swap Floppy Drive Disabled Disabled Enabled Boot Up Floppy Seek Enabled Enabled Disabled Boot Up NumLock Status On On Off Boot Up System Speed High High Low Gate A 20 Option Normal Fast Memory Parity Check Enabled Enabled Disabled Typematic Rate Setting Disabled Disabled Enabled Typematic Rate Chars Sec 6 6 8 10 12 15 20 24 30 Typematic Delay M sec 250 250 500 750 1000 Security Option Setup Setup Sy stem
39. tup or just to Setup System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt The system will boot but access to Setup will be denied if the correct password is not entered at the prompt Note To disable security select PASSWORD SETTING at Main Menu and then you will be asked to enter password Do not type anything and just press lt Enter gt it will disable security Once the security is disabled the system will boot and you can enter Setup freely PCI VGA Palette Snoop It determines whether the MPEG ISA VESA VGA Cards can work with PCI VGA or not Enabled When PCI VGA working with MPEG ISA VESA VGA Card Disabled When PCI VGA not working with MPEG ISA VESA VGA Card PEB 6530VL User s Manual 4 13 BIOS Setup Information OS Select for DRAM gt 64 This item allows you to access the memory that over 64MB in OS 2 The choice Non OS2 OS2 Report No FDD for WIN95 The choice Yes No Video BIOS Shadow Determines whether video BIOS will be copied to RAM However it is optional depending on chipset design Video Shadow will increase the video speed Video shadow is enabled Video shadow is disabled C8000 CBFFF Shadow DC000 DFFFF Shadow These categories determine whether option ROMs will be copied to RAM An example of such option ROM would be support of on board SCSI Optional shadow is enabled Disabled Optional shadow is disabl

PEB-6530VL User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents