Home

elmc1

1. 4 Ventilation The Player should be situated so that its location or position does not inter fere with its proper ventilation For example the player should not be situated on a bed sofa rug or similar surface that may block the ventilation openings or placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings 5 Heat The player should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat 6 Power Sources The player should be connected to a power supply only of the type described in the operating instructions or as marked on the Player 7 Servicing The user should not attempt to service the Player beyond that described in the operating instructions All other servicing should be referred to quali fied service personnel The Player should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the Player C The Player has been exposed to rain or water D The Player does not appear to operate normally or exhibits a marked change in performance American Audio www americanaudio us The serial and model number for this unit is located on the rear panel Please write down the numbers here and retain for future refer ence Model No Serial
2. NOTE This feature has an auto repeat feature so the slider will move smoothly as if a fader was being move 2 FX SELECT SAMPLER SELECT LOOP ADJUSTMENT FX SELECT This knob is used to set the desired FX Once the desired effect appears in the American Audio www americanaudio us ELMC 1 Instruction Manual Page 8 GENERAL FUNCTIONS AND CONTROLS Cont effect window in Virtual DJ press the knob to activate the effect Once an effect is active this knob will temporarily control the effect parameter till the effect is deactivated Press the knob to deactivate the effect SAMPLER SELECT Holding SHIFT while turning this knob will set the sampler on in the sam ple window Rotate the knob left or right once the the desired effect is found Start Stop the sampler by pressing the knob If a sample is active the knob will control the volume temporarily while the sample is playing LOOP ADJUSTMENT If a loop is active this knob can control adjust the loop size till the loop is exited 3 MIXER SECTION CHANNEL GAIN CONTROL This adjustment is used to adjust the audio source signal input gain for a channel Never use the gain control to adjust a channels output volume Setting the gain level properly will ensure a clean output signal An improper gain level adjustment will send a distorted signal throughout the entire audio line which may damage speakers and amplifiers To properly set a channels gain level control 1 Be sure the MAS
3. No Purchase Notes Date of Purchase Dealer Name Dealer Address Dealer Phone ELMC 1 Instruction Manual Page 5 UNPACKING Every ELMC 1 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your player for any damage and be sure all equipment necessary to operate the player has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for further instructions Please do not return the player to your dealer without first contacting customer support INTRODUCTION Introduction Congratulations and thank you for purchasing the American Audioe ELMC 1 Media Controller This controller is a representation of American Audio s continuing commitment to produce the best and highest quality audio products possible at an affordable price Please read and understand this manual completely before attempting to operate your new player This booklet contains important information concerning the proper and safe operation of your new controller Customer Support American Audioe provides a toll free customer support line to provide set up help and answer any question should you encounter problems during your initial set up or operation You may also visit us on the web at www americanaudio us f
4. _ OBJECT AND LIQUID ENTRY Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel DAMAGE REQUIRING SERVICE Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the product If the product has been exposed to rain or water Ifthe product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation Ifthe product has been dropped or damaged in any way When the product exhibits a distinct change in performance this indicates a need for service REPLACEMENT PARTS When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the
5. and maintenance servicing instructions in the user manual accompanying the Media Controller American Audio www americanaudio us RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE CAREFULLY INSERTED TO PREVENT BLADE EXPOSURE CAUTION USE OF CONTROLS OR ADJUSTMENTS OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE THE Media Controller SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL NOTE This unit may cause interference to radio and television reception Please carefully read and understand the instructions in this manual thoroughly before attempting to operate this unit These instruc tions contain important safety information regarding the use and maintenance of this unit Take special care to follow all warning symbols and labels both on the unit and printed in this manual Also Please keep this manual with the unit for future reference CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER TYPE OF ELECTRICAL OUTLET UNLESS THE WIDE BLADES CAN BE CAREFULLY INSERTED INTO A MATCHING WIDE SLOT ATTENTION POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLON GATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT ELMC 1 Instruction M
6. because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or peri odic check up During the period specified above American Audio will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of American Audio under this warranty shall be lim ited to the repair of the product or replacement thereof including parts at the sole discretion of Ameri can Audioe All products covered by this warranty were manufactured after January 1 1990 and bear identifying marks to that effect E American Audioe reserves the right to make changes in design and or improvements upon its prod ucts without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warran ties made by American Audioe in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and o
7. not recommended by the product manufacturer as they may cause hazards WATER AND MOISTURE Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub ina wet basement or near a swimming pool and the like ACCESSORIES Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer CART A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn LA rs VENTILATION Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to POWER SOURCES This product should be operated only fr
8. original part Unauthorized substitutions may resultin fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition WALL OR CEILING MOUNTING The product should not be mounted to a wall or ceiling HEAT The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat isa ANTENNA k LEAD IN WIRE CLAMP ELECTRIC SERVICE EQUIPMENT Fig A GROUND ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE American Audio www americanaudio us ELMC 1 Instruction Manual Page 4 SAFETY INSTRUCTIONS Read Instructions All the safety and operat ing instructions should be read before the Player is operated The safety and operating instructions should be saved for future reference 2 Heed Warnings All warnings on the Player and in the operating instructions should be adhered to 3 Water and Moisture The player should not be used near water for example near a bath tub kitchen sink laundry tub in a wet basement or near a swimming pool etc
9. AMERICAN AUDIO ELMC 1 Professional Digital Producer Featuring SEPEN T 9 Obch grio Seaitiless loon User Guide and Reference Manual 4 13 CONTENTS SAFETY PRECAUTIONS erat at AE cna we E pa chau DU ncaa na ace emdeapenanee 3 BLEG TRIGAL PRECAUTION Sess sissecsitexantenteaseinicvatencnesisnist be nedenreuexavaveustavetinndeien ontario areae daia sgulsentavansl 4 SM I cela tea aes ta cineca saint tal aut nail saad nanttsas siaaadnadanar Dura easimedaucaa saad 5 UNPACKING cas atantasuantezntestescuazeieradenssteadbaassacsnnevennacanssdstasgaaasiarantaansiantausiassecah eaiausabetaslaisiacacuaneiansaneoand 6 CUSTOMER SUPPORT arrea reenact liter E A anauncddagamacinctands 6 SET UP PRECAUTIONS cscesetiessecaiatitas akin esvicaetbas uleniebavevcrisaeeiens vel EEEN EI REEE ENE Pata Sea EEEE rada 6 FEATURES eke aa e E EEE EE E E E E E E E E E E 7 SETUR eeano n a A a E E EAA dads E a 7 FUNCTIONS AND CONTROL S cpaiisictca asia dnattinds rE ERE EEEE AREARE tind EEEE EROARE EEEE EEEE EREE 8 COMPUTER CONNEC TON cclrssizasiainicienss sine iavaarewasailpieeissa siacavateuutecuadeeje si dirada daaa aai Raada TREdi 11 WARRANT Veiane eaea E E E E E E A A AE AE EE 13 SPECIFICATIONS ssgirptsi riepen ariere EARE ERE EAA ETA DE aE ENA Epa 15 Please Note All specifications and improvements to and in the design of this unit and this manuals are subject to change at any time without any prior written or published noticed For service parts visit ht
10. TDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode See Figure A LIGHTNING For added protection for this product during alightning storm or when itis left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges POWER LINES An outside antenna system should notbe located in the vicinity of overhead powerlines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal OVERLOADING Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock IMPORTANT SAFETY INSTRUCTIONS
11. TER VOLUME CONTROL is set to level 4 2 Set the GAIN KNOB to level 8 3 Begin playback on an audio source connected to the channel you are adjusting 4 Use the Gain Control to adjust an average output volume of 4 dB 5 Repeat this step for all channels CHANNEL TREBLE CONTROL This knob is used to adjust the treble levels of a channel allowing for a maximum treble gain of 6dB or maximum decrease of 100dB Turning the knob in a counter clockwise direction will decrease the amount of treble applied to a channel signal turning the knob in a clockwise direction will increase the amount of treble applied to a channel signal CHANNEL MIDRANGE CONTROL This knob is used to adjust the midrange levels of a channel allowing for a maximum midrange gain of 6dB or maximum decrease of 100dB Turning the knob in a counter clockwise direction will decrease the amount of midrange applied to a channel signal turn ing the knob in a clockwise direction will increase the amount of midrange applied to a channel signal CHANNEL BASS CONTROL This knob is used to adjust the low frequency levels of a channel allowing for a maximum bass gain of 6dB or maximum signal decrease of 100dB Turning the knob in a counter clockwise direction will decrease the amount of bass applied to a channel signal turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal 4 MASTER VOLUME CONTROL This knob is used to control the mast
12. anual Page 3 ELECTRICAL SAFETY PRECAUTIONS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons ELECTRICAL PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER OR BACK THERE ARE NO USER SERVICEABLE PARTS INSIDE REFER SERVICE TO YOUR AUTHORIZED AMERICAN AUDIO SERVICE TECHNICIAN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance READ INSTRUCTIONS All the safety and operating instructions should be read before the product is operated RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference HEED WARNINGS All warnings on the product and in the operating instructions should be adhered to FOLLOW INSTRUCTIONS All operating and use instructions should be followed CLEANING The product should be cleaned only with a polishing cloth or a soft dry cloth Never clean with furniture wax benzine insecticides or other volatile liquids since they may corrode the cabinet ATTACHMENTS Do not use attachments
13. ch sensitive and the outside edge of the wheel is not Example You can scratch by touching the inside or center of the wheel and pitch bend when you touch the outside edge of the wheel REAR PANEL GENERAL FUNCTIONS AND CONTROLS LLL A N AQ of k do not ssf pata ln Rafer servico to qualfedsordca RISK en AN Fe cE z4 DO NOT OPEN 13 REAR PANEL 13 USB PORT Connect to your PC for MIDI interface American Audio www americanaudio us ELMC 1 Instruction Manual Page 10 COMPUTER CONNECTION 1 CONNECTING THE ELMC 1 TO YOUR PC Connect the ELMC 1 to your PC by using the USB ports located on the rear of the ELMC 1 and your PC Connect the supplied USB cable to the USB port on the rear of the ELMC 1 and the other end connects to the USB port on your computer NOTE Before connecting your ELMC 1 to your computer or laptop we highly recommend that you install the provided software The Virtual DJ version included with this product is specifically tailored to work with the ELMC 1 with no setup required The setup of other non factory authorized drivers and software is far more complex and in some instances not as reliable Simple Output Configuration Line output ck or RCA l A Mini jack to Mini Jac j DX O O KO ala sound card is optional and not included American Audio www americanaudio us ELMC 1 I
14. er output level To avoid distorted output try to maintain an average output signal level no greater than 4dB To avoid speaker damage that may be caused by excessive volume be sure this knob is always set to zero completely down before turning the unit on 5 NAVIGATION BUTTONS These buttons allow easy navigation of your music library on your soft ware BROWSE KNOB Turn this knob to scroll through and select your music tracks in the soft ware To enter a folder or return to the last folder in the software press the knob LOAD BUTTON Press this button to load the selected track to that deck Pressing this button and the SHIFT button will CUE the source to the headphones SHIFT BUTTON Hold this to use secondary commands for certain buttons American Audio www americanaudio us ELMC 1 Instruction Manual Page 9 GENERAL FUNCTIONS AND CONTROLS Cont 6 LOOP This button will set a 4 beat loop and activate loop divide and multiply functions on the FX select knob 7 PLAY PAUSE BUTTON Press this button to PLAY PAUSE what ever music source is playing 8 CUE Pressing the CUE button during playback immediately pauses playback and returns the track to the last set cue point The red CUE LED will glow when the unit is in cue mode The LED will also flash every time a new CUE POINT is set The CUE button can be held down to momentarily play the track When you release the CUE button it instantly returns to the CUE POINT Y
15. erence 3 Connections 1 Connect USB Cable American Audio www americanaudio us ELMC 1 Instruction Manual Page 7 GENERAL FUNCTIONS AND CONTROLS Figure 1 FX SELECT pe OFXSELECT O OOOO OO PITCHBEND PITCH BEND SAMPLER __ AM RICAN AUDIO FA SAMPLER v PITCH amp A PLAYER FRONT FIGURE 1 1 PITCH BEND BUTTON The pitch bend function creates a momentary Slow Down in the BPM s Beats per minute while it is playing This will allow you to match the beats between two play ing audio sources Remember this is a momentary function When you remove your finger from the pitch button the BPM s will automatically return to the set pitch value Holding down this button will give a maximum of 100 pitch Use this function to slow to another playing music source Be sure to notice that this function is a momentary pitch adjustment for a more precise adjustment use the PITCH FADER to match the BPM s with another playing music source PITCH BEND BUTTON The pitch bend function creates a momentary BUMP in the BPM s Beats per minute while it is playing This will allow you to match the beats between two play ing audio sources Remember this is a momentary function When you remove your finger from this button the BPM s will automatically return to the selected pitch Holding down this button will give a maximum of 100 pitch Hold SHIFT and the PITCH BUTTONS to adjust the pitch fader
16. ngs Keep the unit out of direct sunlight and away from heaters Operate the player only after becoming familiar with its functions Do not permit operation by persons not qualified for operating the unit Most damages are the result of unprofessional operation American Audio www americanaudio us ELMC 1 Instruction Manual Page 6 MAIN FEATURES e MIDI Control e Seamless Loop uninterrupted loop playback e Master Volume Control 3 Band EQ e Crossfader e Durable Touch Sensitive Jog Wheel MINIMUM SYSTEM REQUIREMENTS PC Requirements Windows XP Sp2 or Windows Vista 32 bit amp 64 bit supported PIV 1 2GHz Computer SSE2 CPU AMD 64 or Greater 1024_768 SVGA Video 2 GIG RAM Vista 40MB Free on the Hard Drive Recommended 2000MB DirectX 9 0 Mac Requirements e Mac OS X 10 5 PPC Intel 10 5 6 Intel or 10 6 Intel 1 86GHz e 2GB RAM System Requirements may differ due to manufacturer software SET UP 1 Checking the Contents Be sure your ELMC 1 was shipped with the following 1 ELMC 1 Controller 2 Operating Instructions This Booklet 3 USB Cable 4 Virtual DJ Software 5 Warranty card 2 Installing the Units 1 Place your unit on a flat surface or secure case 2 Be sure the player is in a well ventilated area where it will not be exposed to direct sunlight high temperatures or high humidity 3 Place the unit as far as possible from TVs and tuners as the unit may cause undesirable interf
17. nstruction Manual Page 11 CLEANING Due to fog residue smoke and dust cleaning the mixer should be carried out periodically to residue build up I 2 3 4 Use normal glass cleaner and a soft cloth to wipe down the outside casing Use a cleaner specially designed for electronics to spray in and around the knobs and switch This will reduce small particle built up that can effect the proper operation of the mixer Cleaning should be carried out every 30 60 days to prevent heavy built up Always be sure to dry all parts completely before plugging the mixer in Cleaning frequency depends on the environment in which the mixer operates i e smoke fog residue dust dew American Audio www americanaudio us ELMC 1 Instruction Manual Page 12 WARRANTY WARRANTY INFORMATION The ELMC 1 carries a ONE year 365 days limited warranty This warranty covers parts and labor Please fill out the enclosed warranty card to validate your purchase and warranty All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact American Audios customer support at 800 322 6337 for a R A number All package not displaying a R A number on the outside of the package will be returned to the shipper 1 YEAR LIMITED WARRANTY A American Audioe hereby warrants to the o
18. om the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company LOCATION The appliance should be installed in a stable location NONUSE PERIODS The power cord of the appliance should be unplugged from the outlet when left un used for a long period of time GROUNDING OR POLARIZATION Ifthis productis equipped with a polarized alternating current line plug a plug having one blade wider than the other it will fit into the outlet only one way This is asafety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug If this product is equipped with a three wire grounding type plug a plug having a third grounding pin it will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product OU
19. or any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 823 582 2610 E mail support americanaudio us To purchase parts online visit http parts americandj com Caution There are no user serviceable parts inside this Media Controller Do not attempt any repairs yourself without being instructed to do so by an authorized American Audio service technician Doing so will void your manufactures warranty In the unlikely event your Media Controller may require ser vice please contact American Audiow customer support Do not discard the packing carton in the trash Please recycle when ever possible SET UP PRECAUTIONS Please be sure to make any connections before plugging the player in to an electrical outlet All fader and volume controls should be set to zero or minimum position before the player is switched on If the player has been exposed to drastic temperature fluctuation e g after transportation do not switch on the player immediately The arising condensation of water might damage your device Leave the device switched off until it has reached room temperature Operating Determinations e When installing this player please make sure that the device is not exposed or will not be ex posed to extreme heat moisture or dust Do not operate the player in extremely hot more than 40 104 F or extremely cold less than 5 C 40 F surroundi
20. ou can also tap the CUE button to create a BOP EFFECT 9 SYNC BUTTON Use this button to set this deck to master and auto sync and the other deck s tempo to master 10 VINYL BUTTON Pushing this button activates SCRATCH mode 11 CROSSFADER This fader is used to blend the output signals of channels A and B together When the fader is in the full left position channel A the output signal of channel A will be controlled by the master volume level The same fundamentals will apply for channel B Sliding the fader from one position to another will vary the output signals of channels A and B respectively When the cross fader is set in the center position the output signals of both the channels A and channels B will be even 12 JOG WHEEL This wheel has three functions Attention Make sure that NOTHING is touch or resting on the jog wheels when you power on the ELMC 1 A The wheel works as a pitch bend during Playback Turning the wheel clockwise can increase the pitch percentage up to 100 and turning the wheel in the counter clockwise direction can de crease the pitch percentage down to 100 The pitch bend will be determined on how long you turn the jog wheel continuously B The jog wheel also controls the scratch effect when the scratch effect is active C The jog wheel can also serve as frame search To use frame search the track must be paused and the scratch effect must be disabled Note The inside of the wheel is tou
21. r Dealer s sole remedy shall be such repair or replace ment as is expressly provided above and under no circumstances shall American Audio be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product G This warranty is the only written warranty applicable to American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published American Audio www americanaudio us ELMC 1 Instruction Manual Page 13 NOTES American Audio www americanaudio us ELMC 1 Instruction Manual Page 14 SPECIFICATIONS GENERAL Model American Audio ELMC 1 PC Media Controller Dimensions 399 L x 300 W x 40 H mm 15 7 L x 12 W x 1 5 H Installation Place on flat surface or mount in flat case Weight 10 9 Lbs 4 93 Kgs Power supply USB CHECK THE AMERICAN AUDIO WEBSITE FOR DOWNLOADABLE USER SOFTWARE UPDATES CE American Audio www americanaudio us ELMC 1 Instruction Manual Page 15 American Audio World Headquarters 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 3322 Fax 323 582 3311 Web www americanaudio us E mail info americanaudio us American DJ Europe Junostraat 2 6468 EW Kerkrade Netherlands service americandj eu www americandj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99
22. riginal purchaser American Audio products to be free of manufacturing defects in material and workmanship for a period of 1 Year 865 days from the date of purchase This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service send the product only to the American Audio factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty American Audioe will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in its original package No accessories should be shipped with the product If any accessories are shipped with the product American Audio shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which American Audio concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the American Audioe factory unless prior written authorization was issued to purchaser by American Audioe if the product is damaged
23. tp parts americandj com American Audio www americanaudio us ELMC 1 Instruction Manual Page 2 IMPORTANT SAFETY PRECAUTIONS TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD IMPORTANT SAFETY ITEMS FOR U S A amp CANADA MODEL ONLY WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS Media Controller TO WATER OR MOISTURE CAUTION 1 Handle the power supply cord carefully Do not damage or deform it may cause electric shock or malfunction when used Hold plug attach ment when removing from wall outlet Do not pull on the cord N To avoid electric shock do not open the top cover when the unit is plugged in If problems occur with the unit call your local American Audioe dealer 3 Do not place metal objects or spill liquid inside the Media Controller Electric shock or malfunc tion may occur CAUTION AN A AN Risk of electric shock CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER RACK THERE ARE NO USER SERVICEABLE PARTS INSIDE REFER SERVICE TO YOUR AUTHORIZED American Audio DEALER The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated dangerous volt age within the products enclosure and may be of sufficient magnitude to constitute a risk of electric shock The exclamation point triangular symbol is intended to alert the user to the presence of important operating

elmc1

Contents

Download Pdf Manuals

Related Search

Related Contents