SmartLIGHT single colour Manual
Contents
1. RISK AND LONG LIFE OPERATION For your safety please kindly pay attention to all of the warnings listed below Always plug in the power plug last and disconnect from the mains when the device is not in use or before cleaning Do not install and operate the device in rain or extreme heat moisture or dusty environments This device is for indoor use only and in a dry environment Do not switch on immediately but wait until it reaches to room temperature if the device has been exposed to drastic temperature fluctuations Do not shake the device and avoid brute force when installing or operating Do not spread a fog or bubble effect machine directly at the device Do not use the device during thunderstorms Disconnect the power Do not use solvents or aggressive detergent to clean the device Use a soft and clean cloth Do not modify the device or the power cord in anyway Use appropriate safety rope for added safety Do not stare to the light The symbol mf determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 5m SmartLIGHT User Manual Page 4 CONTROL DISPLAY _ OOO CO MODE ESC UP DOWN ENTER MODE ESC Menu or withdraw the last menu UP Increase one step each time DOWN Decrease one step each time ENTER Confirms the functions you select a a oS Note the display will turn off if no activity for 20 seconds PRIM2. 6 SmartLIGHT User Manual Page 7
3. ARY FUNCTION WG qtx AOO1 A512 DMX 512 Address from 1 to 512 LED Display Action _ O O O o O AUTO Auto Fade in and fade out SOU1 Sound to light strobe SOU2 Sound to light pulse strobe Brightness 25 of full potential Brightness 50 of full potential If there is a breakdown in the DMX connection Brightness 75 of full potential L100 Brightness 100 of full potential SmartLIGHT User Manual Page 9 REAR LAYOUT WG qtx St ee ee lS DMX IN DMX OUT Sound sensitivity Microphone IEC Power OUT IEC Power IN Fuse F1A and F3A for SL Q12 SmartLIGHT User Manual Page 8 WG qtx CONNECT WITH POWER SUPPLY THE GROUND WIRE MUST BE CONNECTED Use the IEC plug to connect to the main power supply as follows a e E E QUICK TROUBLE SHOOTING If the unit is not functioning properly follow the below guidelines Check the IEC cable is fitted correctly Check the fuse hasn t blown in both the IEC cable and unit see below Check any DMX cables are connected correctly Check the DMX address has been set correctly Check the operating mode of the device see later on in this manual If the unit still fails to respond then contact your retailer DO NOT ATTEMPT TO REPAIR YOURSELF REPLACING FUSE First disconnect from the main power supply then remove the fuse holder above the IEC Socket to reveal the fuse Replace with the correct fuse rating as stated on the product safety label Then lock th
4. WG qtx G qtx TECHNICAL SPECIFICATION See individual item for full details aynrdLlrehir For more information visit www avsl qtx com SINGLE COLOUR PAR CANS User Manual DISPOSAL Sy Please disposal of an unserviceable device according to the current statutory requirement Errors and omissions excepted VERSION 1 0 Copyright 2012 AVSL Group Ltd SmartLIGHT User Manual Page 12 www avsl qtx com an EMSS group brand WG qtx INTRODUCTION LED SMARTLIGHT SINGLE COLOUR PAR CAN The QTX SmartLIGHT family of LED Par cans have been designed for a variety of applications whether you re a mobile DJ a band singer a bar nightclub theater company or production company then this range of PAR cans will cover most requirements Please read this manual carefully to ensure you get the best out of these products This manual is a generic manual that covers all available single colour SmartLIGHTS in the range Contents Page 3 6 Product Safety and Installation instructions Page 7 9 SmartLIGHT Product layout Page 10 11 SmartLIGHT Operation and functions Page 12 13 SmartLIGHT DMX Operation SmartLIGHT User Manual Page 2 WG qtx DMX The fixture is equipped with 3 pin XLR connectors for DMX input and output The SE connectors are wired in parallel Only use a shielded twisted pair cable designed for 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another DMX
5. e fuse holder cover back into place SmartLIGHT User Manual Page 5 qtx qtx GENERAL MAINTENANCE FRONT LAYOUT GENERAL To maintain optimum performance and minimise wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced life and increased mechanical wear Be sure to power off the fixture before conducting maintenance Unplug fixture from the mains and use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components Clean all glass and Perspex when fixture is cold with a mild cleaning solution to the cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surface until they free of haze and lint The cleaning of external optical lenses must be carried out periodically to optimise light output Cleaning frequently depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can require cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days LED Output Secondary bracket Mounting point for G Clamp Secondary mounting points for more clearance Thumb screw to hold brackets in place oe a oe i Primary bracket SmartLIGHT User Manual Page
6. output DMX input XLR mounting sockets rear view XLR mounting plugs rear view 1 Shield 2 Signal 3 Signal Building a serial DMX chain DMX 512 Controller operation Master slave operation Caution At the last fixture the DMX cable has to end with a terminator Solder a 120 Ohm resistor between PIN 2 and PIN 3 into a 3 pin XLR plug and plug it in the DMX output of the last fixture SmartLIGHT User Manual Page 11 WG qtx MASTER SLAVE If you have more than one unit you wish to operate the same but do not have a DMX controller or foot controller then you can do so in the following simple way Connect a 3 pin DMX XLR cable from the DMX OUT socket on the master unit and plug in to the DMX IN socket on the slave device Then set the Slave device to DMX address to be A001 and it will repeat whatever operation is current on the master unit This can be repeated for up to 32 fixtures DMX OPERATIONS a 007 Function ___ 008 190 298 199 Dimming 100 _ 0 100 191 200 Sound to 191300 Sound to light pulse __ pulse 196 200 Sound to 126 200 Sound to ight strobe __ strobe a T 247 201 247 Strobe sid 248 255 248 255 Open 100 s_ s s 100 SmartLIGHT User Manual Page 10 WG qtx PACKAGE CONTENTS Please check the contents to ensure that the product has been received in good condition Sma
7. rtLIGHT Box SmartLIGHT Unit x 1pcs User s Guide x 1pcs Power Cord x 2pcs EU and UK Mounting brackets x 2pcs If you find any accessory is missing or the product has arrived with any problems please contact your local dealer at once Do not try to fix this item yourself or you will lose the warranty Please keep the original package and invoice for any possible replacement or returned demand INSTALLATION Every person involved with the installation operation and maintenance of this device should be qualified and follow the instructions in this User Guide We recommend that this product should be used within the guidelines of HSG95 When you connect to the main power supply the device will take a few seconds before ready for use MOUNTING INSTRUCTIONS The mounting brackets are already attached to the product when you open the box but you can adjust them giving more clearance You can use them as floor standing or you can fix a G Clamp to the bracket securely ready for mounting After finding the desired position tighten the G Clamp and use a safety wire the security loop for extra security When selecting an installation location take into consideration routine maintenance Safety cables must always be used Never mount in places where the fixture will be exposed to rain high humidity extreme temperatures changes or restricted ventilation SmartLIGHT User Manual Page 3 WG qtx CAUTION TO PREVENT MORTAL ELECTRICAL
Download Pdf Manuals
Related Search