FCC Certifications CE Mark Warning 1
Contents
1. Mbps 10 Blinking Green port connection and there is 100M data transmitting receiving ff 0 Port disconnected or the port is connected at 1000 Mbps PRR 5 RRR RRR RRR RRR RR ee Re eR eRe RRR RRR RRR RRR RRR Ree ee eee eee eee Attention The Mini GBIC slot shares the same LED indicators with Gigabit RJ 45 copper ports a The Rear Panel Power Receptacle To be compatible with the electric service standards around the world the switch is designed to afford the power supply in the range from 100 to 240VAC 50 60Hz Please make sure that your outlet standard to be within this range To power on the switch plug the female end of the power cord firmly into the receptacle of the switch and the other end into an electric service outlet After the power cord installation please check if the power LED is illuminated for a normal power status Installation This switch can be placed on your desktop directly or mounted in a rack The installation is a snap Users can use all the features of the switch with simply attaching the cables and turning the power on Before installing the switch we strongly recommend 1 The switch is placed with appropriate ventilation environment A minimum 25mm space around the unit is recommended The switch and the relevant components are away from sources of electrical noise such as radios transmitters and broadband amplifiers The switch is away from environments beyond recommend m2. Interface 16 24 10 100 1000 Mbps auto MDI MDI X RJ 45 switching ports 4 Mini GBIC module sockets Cable Connections RJ 45 1LOBase T Category 3 4 5 UTP STP RJ 45 100Base TX Category 5 UTP STP RJ 45 1000Base T Category 5 5e enhanced UTP STP Fiber depend on Mini GBIC types Or Transmission Mode 10 100Mbps Full duplex Half duplex LOOOMbps Full duplex LED indications System Power 16 24 10 100M Link ACT 16 24 1000M Link ACT Memory 8192 MAC entries 16 Port 2 72M bits Buffer Memory 24 Port 4M bits Buffer Memory Power Supply Internal power supply 100 240V 50 60 Hz universal input Dimensions 441mm W x 130mm D x 44mm H 17 36 W x 5 12 D x 1 73 H Weight 1 5Kg 3 3lbs Operating Temperature 0C 45 C 32 F 113 F Storage Temperature 10 C 70 C 14 F 158 Operating Humidity 5 95 non condensing Emission FCC Part 15 Class A CE Mark Class A VCCI Class A
3. No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2006 All Rights Reserved Unpacking Information Thank you for purchasing this product Before installation please verify that your package contains the following items 1 One 16 24 Port Gigabit Ethernet Switch with 4 Port Mini GBIC 2 One AC power cord 3 Rack mount brackets optional 4 User s Manual Introduction General Description Easily boost your networking throughput the product equips 16 24 Gigabit ports that lead you to a real Gigabit connection Users are now able to transfer large and high bandwidth needed files faster and hence get a real efficiency improvement In addition to the copper ports 4 of the ports supports fiber connection with the equipped Mini GBIC ports for obtaining long distance communication This product offers users with fast and reliable network The store and forward architecture filters errors and forwards packets in a non blocking environment Flow control prevent data loss while transmitting The 802 3x and backpressure flow control mechanisms work respectively for full and half duplex modes The switch features with easy installation and maintenance It Supports Nway auto negotiation protocol that detects the networking speed 10 100 1000 Mbps and the duplex modes F
4. FCC Certifications FC This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the latest information
5. oisture Desktop Installation Attach the provided robber feet to the bottom of the switch to keep the switch from slipping The recommend position has been square marked Install the switch on a level surface that can support the weight of the unit and the relevant components Plug the switch with the female end of the provided power cord and plug the male end to the power outlet Rack mount Installation Rack mounting facilitate to an orderly installation when series of networking devices being installed The switch is supplied with rack mounting brackets and screws for rack mounting the unit Procedures to Rack Mount the Switch in the rack Disconnect all the cables from the switch before continuing Place the unit the right way up on a hard flat surface with the front facing you Locate a mounting bracket over the mounting holes on one side of the unit Insert the screws and fully tighten with a suitable screwdriver Repeat the two previous steps for the other side of the unit Insert the unit into the rack and secure with suitable screws optional Reconnect all the cables Network Cables I nstallation 1 Crossover or straight through cable All the ports on the switch Support Auto MDI MDI X functionality Both straight through or crossover cables can be used to connect the Switch with PCs as well as other devices like switches hubs or router 2 Category 3 4 5 or 5e UTP STP cable To make a valid connecti
6. on and obtain the optimal performance Appropriate cables corresponding to different transmitting receiving speed is required To choose a suitable cable please refer to the following table Media Speed Wiring 10 100 1000Mbps 10Mbps Category 3 4 5 UTP STP copper 100Mbps Category 5 UTP STP 1000Mbps Category 5 5e UTP STP 1000Mbps Fiber 1000Mbps The cable type differs from Mini GBIC the Mini GBIC you choose required Please refer to the instruction came with your Mini GBIC Port Operation The auto negotiation feature allows ports running at one of the following operation modes 10 100 1000Mbps 10Mbps copper 100Mbps LOOOMbps Fiber 1000 5 Full Duplex Mini GBIC required Note For the last port when both the fiber and copper interfaces are connected the system adapts the fiber interface and disables the relevant copper port automatically Backbone Network Application This switch is ideal for boosting the throughput of backbone For an application sample of network topology please refer to the following chart Y iF EE Oe TI T EEE 100Mbps Switch 000 5 Server 00 File Web Server Product Specifications Standard EEE802 3 10Base T EEE802 3u 100Base TX EEE802 3ab 1000Base T EEE802 3z 1000Base SX LX EEE802 3x full duplex flow control amp half duplex back pressure
7. ull Half automatically Auto MDI MDI X function alleviates the effort to use crossover cables Also rich diagnostic LEDs are provided for users to get real time information of the connection Status Key Features Complies with EEE802 3 IEEE 802 3u IEEE 802 3ab and IEEE 802 3z standards 16 24 10 100 1000 Mbps RJ 45 Nway ports 4 Mini GBIC port for optional fiber optical communication Supports NWay protocol for speed 10 100 1000Mbps and duplex mode Half Full auto detection Supports MDI MDI X auto crossover Supports full and half duplex operation on all copper ports Supports back pressure half duplex and flow control IEEE 802 3x Wire speed packet filtering and forwarding rate 2 Store and forward architecture Supports 9K Bytes Jumbo frame Supports 8192 MAC address entries in whole system 16 Port 2 72M 24 Port 4M bits buffer memory Internal power adapter FCC VCCI CE Class A Meet RoHS The Front Panel The front panel consists of LED indicators For detailed LED definition please refer to the next paragraph atte 2828 22068 9 LEDs Definition System LED Status Operation Steady Green The switch is powered on Off The switch is powered off Status Operation Steady Green Valid port connection at 1000 Mbps Valid port connection and there is N data transmitting receiving ot ok disconnected or the port is connected at 10 Mbps or 100 Mbps Steady Green Valid port connection at 10 100
Download Pdf Manuals
Related Search