Home
A704 Series User Manual
Contents
1. 2015 Carmanah Technologies Corporation 11 A704 SERIES Carmanah USER MANUAL 4 2 2 Push Button p The push button is used for configuration and control It can be used in conjunction with or instead of a Handheld Controller for most modes and features The two types of push button inputs are Hold Pressing and holding the push button down for several sec will cycle through the command levels The command level is indicated by the number of amber indicator LED flashes Once the desired command level has been reached release the push button Press Momentarily pressing the push button 1x 5x chooses a command within that command level Each momentary press must be quick and less than 1 sec You must select a command within 10 sec of entering a command level otherwise the light exits that command level The green indicator LED flashes the number of accepted momentary presses The red indicator LED flashes three times if the command has not been accepted Indicator LED and push button sequences will be referred to as hold push button for a group of amber flashes press push button For example 4 2 is 1 Hold the push button for a group of 4x amber flashes 2 Press the push button 2x green indicator LED flashes quickly 2x to confirm O 2015 Carmanah Technologies Corporation 12 6 A704 SERIES Carmanah USER MANUAL The following are available push button commands Step 1 Hold fora Step 2 Press for comman
2. 3 3 Standby Mode f Standby Mode turns off the output LEDs and waits for the next day to night transition After this transition the light enters its previous Autonomous Mode Standby Mode is enabled by push button sequence 0 1 or the Handheld Controller 4 3 4 Lights Off Mode i Lights Off Mode turns off the output LEDs indefinitely until it receives a command to turn them on Lights Off Mode is enabled by the Handheld Controller 4 3 5 Emergency Mode Emergency Mode sets all lights in all groups to emergency flash Emergency flash is TEMP HIGH FLASH After 15 min the lights revert to their previous Autonomous modes Emergency Mode is enabled by the Handheld Controller 4 3 6 ARCAL Mode i The Aircraft Radio Control of Aerodrome Lighting ARCAL feature works in conjunction with an ARCAL VHF receiver to allow aircraft pilots to control the lights ARCAL Mode is enabled by the Handheld Controller 4 3 7 Storage Mode p Storage Mode is a low power state used for storing or shipping the light Lights are shipped from the factory in Storage Mode e No response to wireless control and no output from the LEDs e Indicator LEDs are off e Stores the last mode before entering Storage Mode e Sunlight or external power will continue to charge the battery If the ambient light level is 30 lux or less for 24 hours the light will automatically enable Storage Mode Storage Mode is enabled by push button sequence 2 1 To disable S
3. A704 has the following applications The A704 VL has the following applications Self contained high performance solar powered light source Optional 900 MHz ISM wireless control with 2 5 miles 4 km range with available Handheld a Controller SE Easy to install and low maintenance with long life light emitting diodes LEDs Available in red green yellow white blue omnidirectional and white white red green yellow white and bidirectional visible LED output colors Indicator LEDs and push button user interface Intelligent Energy Management System EMS Visible LED and night vision goggle NVG compatible infrared IR LED outputs Aviation yellow or olive drab chassis Optional external connector provides long term high power operation and battery charging Replaceable battery packs Applications Runway edge omnidirectional MIRL amp directional HIRL Runway threshold Emergency or temporary airfield Construction barricade Obstruction Taxiway amp apron edge Helipad Emergency or temporary helipad O 2015 Carmanah Technologies Corporation 6 e carmanah 3 0 Installation Each shipment includes e A704 or A704 VL e Manual e Antenna wireless models only rt lj MILLE Ta NUN 2015 Carmanah Technologies Corporation NAN A704 SERIES USER MANUAL A704 SERIES carmanah USER MANUAL 3 1 Antenna An antenna is includ
4. Carmanah USER MANUAL 4 4 4 Battery Check Push button sequence 4 1 checks the battery state of charge The indicator LEDs then show the following for 10 Sec Indieator Battery State of Charge Charge 50 75 Flashing Red LVD lt 10 4 4 5 Flash Toggle Push button sequence 0 5 toggles between steady on and flashing output LEDs Rate of flash is 0 25 sec on 0 75 sec off 4 4 6 Infrared Toggle p Push button sequence 3 1 toggles between visible and infrared output LEDs 4 4 7 Push Button Lock Toggle Push button sequence 5 2 toggles between locking and unlocking the push button e Red indicator LED flashes 2x when the push button is first locked e When locked push button commands are ignored e f any other push button command is given other than unlocking the push button the red indicator LED flashes 3x e Green indicator LED flashes 2x when the push button is unlocked 4 4 8 Diagnose D The battery state of charge and radio health can be queried via the Handheld Controller using its Diagnose function Diagnose is disabled when LVD is entered 2015 Carmanah Technologies Corporation 19 6 A704 SERIES Carmanah USER MANUAL 4 4 9 Grouping W Y Grouping allows independent control of different subsets of lights on an airfield There are 8 groups numbered 1 through 8 Each light can be assigned to only one group A handheld controller can control multiple groups at a time A light ca
5. Corporation 4 6 A704 SERIES Carmanah USER MANUAL The rate of battery self discharge is very dependent upon temperature The warmer the temperature the faster the batteries will discharge Lights that have been stored will usually require a top up charge before they are put into service The most accurate battery health status reading is obtained when the unit has been in a dark location and in off mode for at least 24 hours 1 3 Wireless Precautions Keep the Handheld Controller at a distance of at least 3 ft 1 m from the antennas of lights or other Handheld Controllers It transmits a powerful radio signal that could damage sensitive receiver circuitry if operated at close range 1 4 Regulatory This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications however there is no g
6. time For security the user has to manually interact with the light for UCS configuration 1 Light must be on for at least 10 sec and not in Storage Mode 2 Press the push button 1x This instructs the light to receive UCS configurations from the Handheld Controller for 5 min 3 UCS configuration is sent from Handheld Controller 4 After successfully receiving a UCS configuration the light flashes for 5 sec Push button sequence 4 2 requests the UCS status from the indicator LEDs Factory default is UCS disabled 4 4 11 Factory Reset p Push button sequence 5 5 performs a Factory Reset that sets the light back to a known state e AUTO LOW visible LED steady on e Group 1 e UCS off Green amber and red indicator LEDs momentarily turn on then turn off once the reset is complete O 2015 Carmanah Technologies Corporation 21 6 A704 SERIES Carmanah USER MANUAL 5 0 Maintenance 5 1 Inspection Although the light is maintenance free significant performance gains can be made with clean solar panels and lenses e Clean the solar panels monthly Use water and a soft sponge or cloth A mild non abrasive cleanser can be used for more stubborn residue Rinse well e Clean solar panels and lenses more frequently during drier months as they may become covered in dust more quickly A pressure washer is not recommended e Visual inspection check the exterior for cracks missing or broken hardware or other potential prob
7. A704 Series e carmanah USER MANUAL pooooo0o DONA i5 Orrro we put solar to work o A704 SERIES carmanah USER MANUAL O 2015 Carmanah Technologies Corporation 2 carmanah USER MANUAL Contents tO Salety Usage ion iio 4 Ll MIGWINGPRECAUTIONS aaa aa 4 DEM uu PESCA ul Said das dass 4 1 3 Wireless PreCautions ccccccccsssccccesseeecseececseeeecceuscesseeseeecsaueeecsauecesseuseeessadeeeesageeesseseeessuseeessaneeessegeeessages 5 ta NRSC ONY estresado TT 5 iS Nara Discreta 9 ME ede mee E 6 ZA O a DE aaa NGAEN aab anapa na aa Ak Laa a Siki 6 22 APPICA ON REESE 6 SEMEL Seti osa 7 Sl uiii cte tmn 8 22 eet EE m TE 9 Ss qe M TP 9 3 DIMENSIONS MOULIN A mU T 10 0 ODO P 11 41 THEON or OSTA ON Nate kaka e A e b kag Ue n tore icd tutes a o ec eaters aaa ees aa a aa 11 4 2 User Ima Lum 11 ds MOdES a UU eee m 14 AA O O ccm S 17 50 CIERTO LLL LPS 22 NEM Ince ero EET mmm 22 5 2 Slagg Battery G Marin is 22 5 9 Battery heplacelerib assunti aba oi iia 23 SD EB evel ew rx 26 5 5 A704 Head Replacement on A704 5 ChaSSiS occccccccconccnnccononnnnnononancnnnononancnnnnnnnnnrnnnnnnnnnrnnnnnnnnnrnnnnnnnnnennnnnnnas 26 6 0 SProUbleshOOllig risa 30 TO Waranty sasana ME 31 A704 SERIES O 2015 Carmanah Technologies Corporation 3 6 A704 SERIES Carmanah USER MANUAL 1 0 Safety amp Usag
8. Energy Management System EMS The capacity of the battery ensures that even with poor levels of sunlight over an extended period the light has enough reserve power to continue to perform reliably Stored battery energy is then available to power the output LEDs in one of several modes These modes are selected using the push button user interface on the light or a Handheld Controller The most commonly used modes are Autonomous and Temporary Modes The Handheld Controller is a transmitting radio that sends commands to a receiving radio inside the light The Handheld Controller is optional and only communicates with lights that have optional wireless control For Handheld Controller operation and button sequences see its manual 4 2 User Interface 4 2 1 Indicator LEDs Inside the lens near the push button are three indicator LEDs that illuminate green amber or red They e Guide push button operation e Indicate diagnostic feedback e Indicate normal operating state after the push button has not been used for 10 sec Green indicator Amber indicator Red indicator Push Button All indicators are off Autonomous or Temporary Mode Infrared LED output Storage Mode Green indicator flashes 1x every 2 sec Autonomous or Temporary Mode Visible LED output Amber indicator flashes 1x every 1 sec Battery is charging via the external connector Amber indicator flashes 1x every 2 sec Battery is charging via the solar panel
9. connect the locking battery harness and remove the chassis disconnect the optional locking charge port harness gt na An ES EA re e NG DN y iN TU B o cu J E Ll n A U soan e um 3 M Tan EC Y n wALED LEAD va A LED LEAD m a ABL O 2015 Carmanah Technologies Corporation 24 A704 SERIES Carmanah USER MANUAL Installing a battery pack is similar to the above steps 1 Slide the battery pack over the mounting post noting the correct orientation to the base plate Tighten the central bolt and its hardware to 40 in lbs Connect the optional charge port harness Ensure the base plate gasket is clean and seated in its groove Hold the chassis over the battery pack and connect the battery harness Align the handle with the base plate and battery pack and slowly slide the chassis down Ol eS 7 Tighten 4 base plate screws to 40 in Ibs 2015 Carmanah Technologies Corporation 25 A704 SERIES carmanah USER MANUAL 5 4 Recycling This product required the extraction and use of natural resources It may contain substances that could be harmful to the environment or human health if improperly handled at the product s end of life In order to avoid release of such substances into the environment and to reduce the use of natural resources we encourage you to recycle the product in an appropriate way that will ensure most of the materials are reused or recycled appropriately Check
10. d group of No hold Standby Mode utonomous Low Autonomous Med Autonomous High Flash Toggle 0 1 0 2 0 3 0 4 0 5 Temporary Low Temporary Med Temporary High 1ambertiash TU Ta ra oem group of gt Storage Mode 2 amber flashes 2 1 Infrared Output Visible Output Visible amp Infrared ONLY 8 1 ONLY 8 2 Outputs 3 3 Infrared Toggle 3 1 group of gt Battery Check UCS Status 4 amber flashes 4 1 4 2 group of gt Button Lock Toggle Factory Reset 5 amber flashes 5 2 5 5 For engineering purposes only use may result in unpredictable behavior of the light For optional wireless control toggling between Visible and Infrared Outputs is done with 3 1 or by using the Handheld Controller Use the command once to toggle from Visible gt Infrared A second command will toggle the output from Infrared gt Visible 2015 Carmanah Technologies Corporation 13 6 A704 SERIES Carmanah USER MANUAL 4 3 Modes 4 3 1 Autonomous Mode Q In Autonomous Mode the output LEDs turn on during the night and turn off during the day The change from day to night or night to day is known as a transition A built in ambient brightness sensor detects transitions Autonomous Mode setting is recommended by a solar simulation NOTE oee carmanah com for a solar simulation for your application Correct setting is important to ensure sustainable year round operation The Autonomous Mode setting is selected by pus
11. e The following symbols indicate important safety warnings and precautions throughout this manual WARNING indicates that serious bodily harm or death may result from failure to adhere to the precautions CAUTION indicates that damage to equipment may result if the instructions are not followed NOTE suggests optimal conditions and provides additional information WIRELESS features and functions that require a Handheld Controller PUSH BUTTON features and functions that require interaction with the push button on the light 1 1 Viewing Precautions Do not view an actively emitting infrared or visible light from the side or top of the light close to or on beam from a range of less than 4 ft 1 2 m Q A safe limit for near infrared viewing established by the American Conference of Governmental and Industrial Hygienists ACGIH is 65 mW in 10 mW cm as the maximum exposure limit for viewing for up to 16 minutes This power density can be produced at the lens surface when actively emitting infrared light 1 2 Battery Precautions Use extreme caution when handling the light This product is capable of generating enormous short circuit currents Remove all jewelry bracelets metal strap watches rings before attempting to handle or remove the batteries Charge your battery periodically Permanent damage and reduced capacity will result if the battery is not correctly maintained gt Q 2015 Carmanah Technologies
12. ed with each light ordered with optional wireless control Grip the antenna by its metal base and hand tighten it onto the antenna connector The effective range of the wireless control system is 2 5 miles 4 km Wireless range is greatly affected by use and location To achieve the best wireless range e Handheld Controller antenna is parallel to the light s antenna e Elevate the Handheld Controller s antenna e Ensure surrounding grass and foliage is trimmed e Clear line of sight between antennas 2015 Carmanah Technologies Corporation 8 6 A704 SERIES Carmanah USER MANUAL 3 2 Location Year round unrestricted solar exposure is critical to long term performance Shade dramatically reduces the ability of the light to charge its battery Year round sun During the winter the sun is lower on the horizon Because the angle of the sun changes with the seasons be aware that obstructions such as trees buildings and mountains that do not shade the solar panel during the summer may shade it during the winter 4 77 NN INN i Y N HAHAHA ih HH HET ANNA TT HL y NN ANNAN NN N NA SE Cooler is better The battery lasts longest if you can minimize its exposure to high temperatures Choose a location that is away from hot dark colored surfaces like asphalt or black steel plate Mounting kits are available that elevate t
13. h button sequence 0 2 0 3 0 4 or the Handheld Controller AUTO LOW AUTO LOW IR No AUTO LOW FLASH 0 25 sec on 0 75 sec off AUTO MED FLASH 0 25 sec on 0 75 sec off AUTO HIGH FLASH 0 25 sec on 0 75 sec off AUTO LOW IR FLASH 0 25 sec on 0 75 sec off AUTO MED IR FLASH 0 25 sec on 0 75 sec off AUTO HIGH IR FLASH 0 25 sec on 0 75 sec off Factory default is AUTO LOW visible LED steady on Active Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn Dusk to dawn 2015 Carmanah Technologies Corporation 14 6 A704 SERIES Carmanah USER MANUAL 4 3 2 Temporary Mode Y A Temporary Mode activation interrupts other modes and ignores transitions This activation lasts for a preset time of 15 minutes and then the light reverts to its previous Autonomous Mode Maximum number of Temporary Mode activations per day is recommended by a solar simulation NOTE See carmanah com for a solar simulation for your application Correct usage is important to ensure sustainable year round operation The Temporary Mode setting is selected by push button sequence 1 1 1 2 1 3 or the Handheld Controller Activation Activation Output Handheld push Intensity LEDs Controller button command command O 2015 Carmanah Technologies Corporation 15 6 A704 SERIES Carmanah USER MANUAL 4
14. he light and can help reduce the temperature of the battery Flat Ensure the mounting surface is flat and level 3 3 Orientation The handle can be used to orient the light relative to the runway This is useful for directional and bidirectional lights 3 8 7967 Hed Green directional m e 4 b N Ji et White mes directional omnidirectional O 2015 Carmanah Technologies Corporation 9 d A704 SERIES carmanah USER MANUAL 3 4 Dimensions amp Mounting The A704 has a common head and base The solar engine varies depending on the application Compact Solar Engine Standard Solar Engine Large Solar Engine Optional wireless antenna shown Optional wireless antenna shown Optional wireless antenna shown Optimal for high solar or Optimal for most applications Optimal for low solar or low use applications high use applications 4 2 vdc 15 Ahr battery 63 Whr total 4 2 vdc 24 Ahr battery 101 Whr total 4x 1 7 W Solar Panels 6 8 W total 4x 3 8 W Solar Panels 15 2 W total 4x 3 8 W Solar Panels 15 2 W total Mount using 0 5 in 12 mm fasteners Fasteners are not included but are available as kits 7 87in 200mm BOLT 0 65in 9 25in CIRCLE 15 7mm 6 HOLES SN 3 HOLE MOUNTING 4 HOLE MOUNTING 2015 Carmanah Technologies Corporation 10 6 A704 SERIES Carmanah USER MANUAL 4 0 Operation 4 1 Theory of Operation During daylight the solar panels charge the battery using the
15. ight and wait flashing brightness is above 500 lux 20 sec for the light to turn on Nearby lights are Increase distance between lights illuminating the ambient turn off unneeded lights or shield Use push button infrared toggle 3 1 brightness sensor lights O 2015 Carmanah Technologies Corporation 30 A704 SERIES Carmanah USER MANUAL 7 0 Warranty This product is covered by the Carmanah warranty Visit carmanah com for additional information Before contacting Carmanah s customer service department please have the serial number of your light available a brief description of the problem as well as all details of the installation and recharging efforts To contact Customer Service Mail Carmanah Technologies Corp 250 Bay Street Victoria BC Canada V9A 3K5 Phone 1 250 380 0052 worldwide 1 877 722 8877 toll free U S and Canada Fax 1 250 380 0062 Email customerservice carmanah com Website carmanah com 2015 Carmanah Technologies Corporation 31 O 2015 Carmanah Technologies Corporation carmanah 2015 Carmanah Technologies Corporation Technical Support Email customerservice carmanah com Toll Free 1 877 722 8877 US Canada Worldwide 1 250 380 0052 Fax 1 250 380 0062 Web carmanah com we put solar to work 72936 A704 UserManual RevC
16. is ready for service 2015 Carmanah Technologies Corporation 29 6 A704 SERIES Carmanah USER MANUAL 6 0 Troubleshooting Output LEDs are off All indicator LEDs are Infrared output LEDs are on De select the IR button on the Handheld Controller and send a visible output command Unresponsive to 2n wireless control Use push button infrared toggle 3 1 otorage Mode is active De activate Storage Mode by pressing push button 1x Output LEDs flash LVD is entered Charge the battery once every 60 sec Hed indicator LED is flashing Output LEDs are on Green indicator LED is Mismatched groups Ensure the Handheld Controller s or off flashing and light s group match E a UCS is enabled Ensure the Handheld Controller s and light s UCS match or turn off UCS Antenna not installed Ensure the light s antenna is properly installed Handheld Controller Check Handheld Controller problem battery PIN status and Pass through Battery is bad Replace the battery Output LEDs are off All indicator LEDs are Unresponsive to Ru Wales MISI Battery is not connected Check that the battery connector is fully inserted Unresponsive to push button Output LEDs are off All indicator LEDs are Infrared output LEDs are on De select the IR button on the in Autonomous off Handheld Controller and send a Mode visible output command Green indicator LED is Daylight ambient Darken the entire l
17. lems 5 2 Storage amp Battery Charging When storing the light it is important to maintain the battery e Put the light in Storage Mode or disconnect the battery e Store in a cool location e Check the battery state of charge once per month Do not use the Lights Off Mode for storing the light The radio is still active in this mode and may receive wireless commands If charging is required charge the battery fully using one of several methods Time to Charge from 10 to 100 State of Charge Incandescent light bulb 60 W gt 1000 hrs 12 in 30 cm from solar panels Halogen light bulb 500 W 600 hrs 24 in 60 cm from solar panels Direct sunlight 150 hrs Available AC plug in charger attached to the optional charge 18 hrs port O 2015 Carmanah Technologies Corporation 22 A704 SERIES USER MANUAL Carmanah 5 3 Battery Replacement DO NOT INSTALL A702 A703 A704 5 A704 H 800 Series BATTERY PACKS A704 battery packs are nominal 4 2 vdc and have unique harnessing 4 2V Use of an incorrect battery pack will damage the EMS permanently Look for the red 4 2V label on the top of the pack A704 is configurable and has several battery pack options This instruction shows a typical battery pack If the battery is permanently damaged and needs to be replaced 1 Remove the 4 base plate screws using a 5 32 in hex driver O 2015 Carmanah Technologies Corporation 23 6 A704 SERIES carmanah USER MANUAL 3 Dis
18. longer be used with the new head Do not leave the screw loose in the bottom of the chassis as this could cause damage to the light during handling 5 Using a Y in hex socket remove the battery retention bolt holding down the ground cable Remove the ground cable and recycle Reinstall the battery retention bolt and hardware tighten to 200 in lbs O 2015 Carmanah Technologies Corporation 27 6 A704 SERIES Carmanah USER MANUAL 6 Install the adaptor harness that came in the kit onto the main head connector Ensure the white dots are aligned Press the two sides together until 2 audible clicks are heard Care must be taken to ensure that the pins in the adaptor harness are aligned correctly or a battery short circuit may occur a 7 Reconnect the battery harness and press together until it is latched 8 Connect the free end of the harness to head connector The indicator LEDs will light and then start blinking The head handle must be aligned with the military charge port 2015 Carmanah Technologies Corporation 28 6 A704 SERIES Carmanah USER MANUAL 9 Place head on to light ensuring no wires are pinched between the chassis body and the head Also ensure the gasket is inside the groove in the head Reinstall the 4 top security hex screws in in a star pattern tighten to 70 in lbs The plastic washer is no longer needed and can be recycled 10 The head replacement is complete and your light
19. n be reassigned to another group as required When adding a light to a group the Handheld Controller re sends the last mode to everyone in that group In order to configure the group of a light ile 2 3 4 D Light must be powered for at least 10 sec and not in Storage Mode Press the push button 1x This instructs the light to receive grouping configurations from the Handheld Controller for 5 min Grouping configuration is sent from Handheld Controller After successfully receiving a grouping configuration the light receives that group s last mode from the Handheld Controller Light exits its 5 min window where it would receive grouping configurations Factory default is group 1 O 2015 Carmanah Technologies Corporation 20 6 A704 SERIES Carmanah USER MANUAL 4 4 10 Unique Code Sequence amp Unique Code Sequence UCS allows one or more Handheld Controllers to be uniquely associated to one or more lights When UCS is enabled the Handheld Controller sends a code with each radio transmission Only lights configured to accept that particular code will respond to the transmission The benefits are Independence Nearby installations of lights can be operated independently by different Handheld Controllers without interference Security It is not possible for another Handheld Controller to interrupt airfield operation The Handheld Controller cannot control UCS configured and non UCS configured lights at the same
20. torage Mode press the push button 1x O 2015 Carmanah Technologies Corporation 16 6 A704 SERIES Carmanah USER MANUAL 4 4 Features 4 4 1 Low Voltage Disconnect Low Voltage Disconnect LVD protects the battery from being discharged to levels low enough to cause permanent damage When LVD is entered e Radio and output LEDs are disabled e Output LEDs flashes 0 1 sec every 60 sec to let the user Know the light needs attention e Red indicator LED is flashing e Battery continues charging e When the battery state of charge reaches an acceptable level LVD is exited LVD is enabled in all modes 4 4 2 Automatic Light Control Automatic Light Control ALC is a patented algorithm that matches the light s energy consumption to its energy storage As the battery state of charge diminishes ALC decreases the output LED intensity ALC has 4 intensity steps until finally entering LVD The ALC step depends on the battery state of charge This ensures the light will continue to operate through periods of poor sunlight ALC is enabled in all Autonomous Modes ALC is disabled in all Temporary Modes 4 4 3 External Power Charge Ports If continuous high intensity output or backup power is required external power can be provided to the charge port on the base plate When connected external power is used to power up the light and charge its battery External power is not a control signal and cannot configure the light The push bu
21. tton or Handheld Controller is still used for normal operations When external power is provided to the connector on the base plate the light will not exit Temporary Mode after a preset time It will remain in Temporary Mode until commanded otherwise or until the light detects that external power is no longer available There are 2 optional charge ports charge port and military charge port O 2015 Carmanah Technologies Corporation 17 A704 SERIES carmanah USER MANUAL 4 4 3 1 Military Charge Port The military charge port is on top of the base plate Remove the connector cap and attach a power cable terminated with the correct mating connector and pin out PIN C NOT USED PIN A INPUT GROUND PIN B 9 0 to 13 5 VDC INPUT Military Charge Port e MS3116 connector detailed in MIL DTL 26482 approved vendor Amphenol PT06 E 8 3P SR 025 e Connector accepts 24 20 AWG stranded wire e 9 0 to 13 5 VDC input O 2 2 A max 4 4 3 2 Charge Port The charge port underneath the base plate is intended for temporary indoor charging and not for permanent outdoor installations Remove the connector cap and attach a power cable terminated with a barrel connector Route the cable out under one of the base plates notches Pp A ALIEN ARIES Y NO DN e 9 0 to 13 5 VDC input 2 2 A max 5 5 mm OD 2 5 mm ID INPUT 9 0 TO 13 5 GROUND VDC INPUT O 2015 Carmanah Technologies Corporation 18 6 A704 SERIES
22. uarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off or on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada 1 5 Warranty Disclaimer This manual will familiarize you with the features and operating standards of the product Failure to comply with the use storage maintenance or installation instructions detailed in this manual could void the user warranty Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Installation work must be done by a qualified person s in accordance with all application local codes and standards O 2015 Carmanah Technologies Corporation 5 A704 SERIES carmanah USER MANUAL 2 0 Introduction 2 1 Features The A704 Solar Airfield Light has the following features 2 2 The
23. your local municipality for electronics recyclers pl The symbol indicates that this product complies with the European Union s requirements according to Directive 2002 96 EC on waste electrical and electronic equipment WEEE EET AY e The battery is a rechargeable lead acid battery Consult your local laws for information on recycling Pb 5 5 A704 Head Replacement on A704 5 Chassis If you have an A704 5 and you have received an A704 head replacement please follow these instructions below To determine if your light is an A704 5 please check the white label located on the circuit board inside the lens See the pictures below for examples of an A704 5 Use extreme caution when handling the batteries Do not allow any metal object to contact the exposed battery terminals 1 Remove the 4 top head screws using the included 5 32 in security hex driver included in the kit 2 Lift off the head by the handle and disconnect the white connector by pressing the latch and pulling apart O 2015 Carmanah Technologies Corporation 26 A704 SERIES carmanah USER MANUAL 3 Remove the main head connector by pressing on the two raised sides and pulling straight apart Be very careful not to bend or damage pins in this connector It may short the battery or permanently damage the connector 4 Using a 2 Phillips screwdriver remove the ground screw from the top of the head This screw can be recycled since it will no
Download Pdf Manuals
Related Search
Related Contents
Omega Vehicle Security CN3271 Series User's Manual The Hive Specification - Co 20RC01-00 E4 User Manual iDVR - GeniusEye.com EasyMax - Bedienungsanleitung Copyright © All rights reserved.
Failed to retrieve file