User`s manual "VENTS CF" ( PDF 1,53Mb )
Contents
1. GY VEIT O VENTE 0 F FAN ELECTRICAL CONNECTION AN WARNING The fan shall be connected through the switch with the gap between the dead contacts not less than 3 mm for all poles Mounting and connection examples of the fan are shown in fig 13 31 and diagrams 1 6 The connection of the fan to the power supply network is as follows route the supply cables through an opening in the casing bottom or make a special hole in the casing cover in case of the lateral cable connection fig 14 strip the cable ends for 7 8 mm and insert those into respective terminals to the stop and fasten with screws fig 15 fix the cables with a retaining clip fig 14 cover the fan fig 16 connect the fan to the power supply network fig 17 The connection of the three speed fan to the power network is as follows lead out the supply cables through an opening in the casing bottom or cut a special hole in the casing cover in case of cable connection on side fig 14 screw out the cover of the electrical part of the fan fig 22 strip the cable ends for 7 8 mm and insert those into respective terminals to the stop and fasten with screws fig 23 fix the cables with a retaining clip as shown in fig 14 cover the fan fig 24 connect the fan to the power supply network fig 25 All mounting and connection works are allowed with the fan disconnec2. User s manual CONVENTI CONTENT Purpose Delivery set Basic technical data Fan designation key Safety requirements Fan structure Mounting and preparation to operation Mounting options Mounting sequence Fan electrical connection Wiring diagrams Servicing and maintenance Storage rules Manufacturer s warranty Acceptance certificate Warranty card DODDODODODDODODODSD GE 0 0 N Ao A Y O OQ 12 14 23 23 25 27 27 GE The centrifugal fan VENTS CF further referred as the fan is designed for exhaust ventilation of living spaces offices shops kitchens WCs and other residential and public premises heated during winter time The fan is suitable for ceiling or wall mounting The operating medium must not contain any dust or other solid particles sticky substances and fibrous materials concentrated above 100 mg m The delivery set comprises fan 1 pce decorative front panel 1 pce dowels and screws 4 sets user s manual 1 pce packing box 1 pce The delivery set for the CF 100 turbo comprises 3 sets The fan is designed for connecting to single phase AC power supply network with voltage 220 240 V and 50 Hz frequency or 12 V voltage and 50 Hz frequency for low voltage 12 V modifications The fan is designed for operation in the temperature range between 0 C and 45 C The fan does not cause interference with radio TV or video equipment The m
3. system must be equipped with an automatic circuit breaker The fan shall be connected through the switch integrated into fixed wiring system Keep the clearance between the dead contacts not less than 3 mm for all poles Before installation works make sure that the fan impeller casing and grille are free of any visible damages and that the casing has no foreign objects inside that can damage the impeller blades Misuse of the device any unauthorized alteration or modification is prohibited The device is not designed to be used by children physically or mentally disabled persons persons with sensory disorder persons with no appropriate life experience and or expertise unless they are properly instructed about the device use or supervised by the person in charge for their safety Keep the device out of reach of children or supervise the children to avoid their playing with the device SAFETY REQUIREMENTS A WARNING amp PROHIBITED a WARNING O VENTE 0 F Take precautions to prevent penetration of smoke carbon monoxide and other flame products into the room through open chimney flues or other fire protection devices Take also measures to disable gas back draft in case of using gas or open flame devices The operating medium must not contain any dust or other solid particles sticky substances and fibrous materials The fan operation in the environment containing flammable substances or vapo
4. ble for wall and ceiling mounting The mounting options are shown in fig 2 7 In case of wall mounting fig 2 the fan is fastened to the wall with self tapping screws included into delivery set In case of mounting as shown in fig 3 the fan is mounted by means of the fastening brackets Bend the fastening brackets for the required length to suit mounting requirements The mounting option in fig 4 provides the fan installation on the construction foam The mounting option in fig 5 provides the fan installation of the fan in a specially designed recess The fan is mounted to ceiling either with fastening brackets fig 6 or inserted into a specially designed recess fig 7 The wall mounting sequence is shown in fig 8 10 The built in wall mounting sequence is shown in fig 11 and the ceiling built in mounting sequence is shown in fig 12 The basic delivery set does not include fastening brackets WENT GE 99 1 u VY Sn Barty VN noe no a ada Woven gt Flush wall mounting with fastening brackets Flush wall mounting with construction Built in recess mounting O VENTI Ceiling mounting with fastening brackets MOUNTING SEQUENCE Ceiling mounting inside a specially designed recess eu IN ES WL La CD soc a
5. e of sale Turbo 12 QVANTS ACCEPTANCE CERTIFICATE WARRANTY CARD V18EN 02
6. ff after a time period between 2 and 30 minutes that is adjusted by rotating the potentiometer T clockwise to increase the turn off time and counter clockwise to decrease it respectively fig 27 The fans with timer and humidity sensor modification have the function of automatic turning on as the humidity level in the ventilated area reaches the set value adjusted by rotating the potentiometer between 50 and 90 clockwise to increase the set value and counter clockwise to decrease it within the time period set by the timer fig 28 The timer circuit is under mains voltage Any adjustments are allowed with the fan WARNING disconnected from power supply network only A OYENTE C F Wiring diagram of the fan with timer timer and humidity sensor modification connected in parallel with the lighting lamp and controlled from a common switch After the light in the room is turned off the fan continues operation within the time period set by the timer CEILING MOUNTING B junction box M fan C lighting lamp S light switch diagram 5 Cc F O VENTI The fans with timer and motion sensor modification have the function of the automatic turning on in case of motion detection at the distance from 1m to 4m and the horizontal viewing angle range 100 as well as automatic turning off within the time period set by the timer from 2 to 30
7. he fan with other unsorted municipal trash GE GY VEIT E QYVANTS While purchasing the unit the Customer accepts the following warranty terms Manufacturer hereby guarantees steady performance of the fan within 60 months since the date of its sale in accordance to the rules of transportation storage assembling and operation MANUFACTURER S WARRANTY The warranty is valid only with this user s manual filled in manufacturing date and invoice The fan model shall be of the same type as stated in the user s manual In case of no confirmation of sales date the warranty period is calculated from the production date Failure to submit the user s manual with filled manufacture and sales date may result in refuse for free servicing of faulty equipment All the units and components belonging to the faulty goods and replaced within the warranty period shall be covered by the previous warranty period and general warranty conditions Thus the warranty period is neither extended nor renewed for the replaced components or the unit In case of any failures due to faulty manufacturing during warranty period the Customer has the right to have the goods replaced at the manufacturing facility The accessories operated together with the unit both included and not included into the delivery list as well as other equipment operating jointly with the unit shall not be covered by the warranty The company is not respons
8. ible for compatibility of their goods with other producers goods The warranty covers only the manufacturing defects All the defects and faults resulting from mechanical effect during operation process or natural wear and tear shall not be covered by the warranty conditions The faults caused by violence of operation servicing and maintenance guidelines either by Customer or third parties or caused by unauthorized design modifications shall not be covered by warranty O VENTI C F NO LIABILITY FOR THE RELATED DAMAGES The manufacturer is not responsible for any mechanical or physical damages resulting from the manual requirements violence the unit misuse or gross mechanical effect The indirect damages such as re installation or re connection of the unit direct or indirect losses etc related to the unit replacement shall not be indemnified Mounting dismantling connection disconnection and regulation of the unit shall not be covered by the warranty The contractor in charge for quality of mounting electric mounting and adjustment works shall be responsible for the warranty thereof In any case the indemnity amount shall not exceed the actually paid value for the defective unit price GE 5 CF 3 100 TH CFA TP The fan is recognized as serviceable Stamp of the acceptance inspector Manufacturing date Sold by name of the vendor stamp of the shop Dat
9. inimum service life is 5 years O VENTI PURPOSE DELIVERY SET BASIC TECHNICAL DATA OY VENTS FAN DESIGNATION CXXX 100 X X KEY Fan and filter type C centrifugal F synthetic filter FA aluminium filter Number of speeds _ the fan has one speed by default 3 three speed fan 100 exhaust pipe diameter mm V electrical switch modification GE Motor modifications T timer modification TH timer and humidity sensor modification TP timer and motion sensor modification Designation key example turbo high powered motor 12 low voltage motor 12V 50 Hz VENTS CF 100 VTH turbo CF series fan sincludes a synthetic filter flange diameter 100 mm equipped with an electric switch timer humidity sensor and single phase high powered motor C P O VENTI Protection rating against access to dangerous parts and water penetration IP 24 for fans with a synthetic filter IP 34 for fans with aluminium filter Disconnect the fan from power mains prior to all connection adjustment servicing and repair works Only the qualified electricians authorized for independent electrical works at electrical installations with the voltage up to 1000 V are allowed for servicing and maintenance of the fan after reading this manual Single phase power network used for connection of the device must be in compliance with the acting norms and standards The fixed wiring
10. minutes and adjusted by rotating the rotating the potentiometer T clockwise to increase the turn off time and counter clockwise to decrease it respectively fig 30 The timer circuit is under mains voltage Any adjustments are allowed with the fan WARNING disconnected from power supply network only IN BY VENTI 0 F Wiring diagram of the fan equipped with timer and motion sensor B junction box M fan C lighting lamp S light switch Diagram 6 C F O VENTE Maintenance works are allowed after the fan is disconnected from power supply SERVICING AND network only MAINTENANCE Maintenance means regular cleaning of the fan surfaces from dust and dirt The synthetic filter should be replaced when clogged but at least once in 6 months To clean the aluminium filter remove the cover with the filter fig 33 remove the filter fig 34 wash it with warm water and detergent solution fig 35 and dry it out install the filter inside the cover and snap the grille fig 36 cover the fan Store the fan in the original packaging in a ventilated premise at the temperature from STORAGE 5 C to 40 C and relative humidity not exceeding 60 at 20 C RULES Vapours of acid alkaline and other aggressive admixtures in the operating medium Are not allowed Recycle the device at the end of service life Do not dispose t
11. ted from power supply network only QVANTS __ AQ SD VENTE 0 F WIRING DIAGRAMS Wiring diagram of the fan for connection to the external socket S light switch C lighting lamp B junction box M fan E external socket diagram 1 C P O VENTI Wiring diagram of the fan with built in switch B junction box M fan C lighting lamp S light switch diagram 2 OYENTE C F Wiring diagram of the fan without built in switch through the external switch B junction box M fan C lighting lamp S light switch Sm external switch of the fan Diagram 3 QVANTS P3 1 300 O VENTI C F Wiring diagram of the three speed fan with external speed switch P3 1 300 B junction box M fan C lighting lamp S light switch Sm external switch of the fan P3 1 300 not included into delivery set diagram 4 C F O VENTI The fans with timer modification have the function of automatic shuto
12. urs such as spirit gasoline insecticides etc is not allowed Do not close or block unit inlet and outlet vents to ensure the most effective air passage Do not sit or put objects on the unit The owner of the goods should follow the requirements set forth herein Don t use the fan for operation in explosive dust air mixture environment Do not operate the fan beyond the specified operating temperature conditions as well as in environments containing aggressive mixtures Disconnect the fan from power mains prior to all installation connection adjustment and repair works C E DVENTS FAN STRUCTURE casing removable cover filter grille decorative frame runner scroll casing indicating lamp ANOAAARWNH The VENTS CF fan fig 1 consists of the casing 1 with the motor and impeller 6 assembled inside of the casing The impeller 6 is located in the scroll casing 7 The frame 5 is locked inside the casing 1 and functions as a stopper in case of Through the wall mounting The swivel cover 2 with the fixed grille 4 is attached to the casing The filter 3 is inserted into a space between the cover and the grille The back valve is installed on the fan back side in the exhaust pipe The LED lamp 8 indicates the fan ON OFF operation O VENTI 0 F MOUNTING AND PREPARATION TO OPERATION MOUNTING Wall mounting OPTIONS The VENTS CF fans are suita
Download Pdf Manuals
Related Search