Home
English - Belkin
Contents
1. o rs a bo ng NG F d bo 5 pe N l o a J o ka e PF a s a GETTING STARTED Adding Computers to Your Network Wireless devices such as computers network printers and gaming systems can connect to your Router with a few simple steps Manual Setup If you Know what sort of Internet service you have you might try a manual setup For this you will need a Wi Fi enabled smartphone tablet or computer Wirelessly Connect to Your Router The default network name and password are printed on the foot of the Router Use your computer tablet or smartphone to connect to the wireless network shown on the network ID card able baker zebranet When requested please enter the password security key provided on the card Using the WPS Button Start WPS Push Button Connection WPS PBC on your computer or other Wi Fi device that you would like to connect wirelessly to your Router Often there will be a button for this purpose in software that came with the device or a physical WPS button on the device itself Within two minutes press the WPS button on your Router The WPS indicator will blink green while it listens for your Wi Fi device Once a connection is established the light will turn green for about 5 minutes and then go out If a connection is not established the light will blink green for 30s You may repeat the process to try again You can repeat this process for each WPS ena
2. In the address bar of the Web browser type http 192 168 2 1 i belkin Router Setup Home nen Coop Click Login in the upper right corner of the page The Router does not ship with a password so just click Submit Channel and SSID security 23 USING YOUR ROUTER Click on Channel and SSID in the left column under the Wireless heading Configure the following parameters SSID Set the wireless network name The SSID can contain up to 32 alphanumeric characters The default SSID is belkin Broadcast SSID If checked the Router broadcasts its SSID in the wireless network so that wireless clients can scan the SSID and access the wireless network under the SSID The check box is selected by default If the check box is cleared only devices that know the correct SSID can connect to the Router For the remaining settings use the defaults Wireless gt Channel and SSID 002 1 Te WM Qos gt The default channel is Auto It is unnecessary to change the wireless channel unless you notice interference problems with another nearby wireless Router or access point Select a channel that is not being used by any other nearby wireless networks The default mode is 802 11b g n If you do not know which mode to use select 802 11b g n The default bandwidth is 20 40MHz The default protected mode is Off In most situations best performance is achieved with Protected Mo
3. E Desktop gt E Ed my Documents J 4 My Computer My Recent Jmy Network Places Documents F5D8232 6_WiW_1 E 123 D My Network File name F5DB232 6 ww 16 bin v Places Files of type All Files z Select the firmware file an img file by left clicking on it and then click the Open button in the lower right corner of the window This will take you back into the Router s interface Click the Update button Congratulations The firmware has been updated successfully Utilities gt Firmware Update From time in tine Bekin may eines mre versions ofthe Routers taman Fimeware updates contain imprreeniant and fame bo probia Iha may here emrited Click ihe link below lo nag here id a naw frente update available fortis Router NOTE Pinann backup your current satinga betore updating jo anew version otra Click Here do go fo te Bamailhaekyp current malinga page Damiana et koa FEPNA Nye TON Check For Mew Ariana Pagalon Check Ameera Aqu rio Hina 3 CO Dacument and Sofia Aad CU Lipe Utilities 5 Firmware Update Successfully Router is rebooting52seconds remaining 34 USING YOUR ROUTER Configuring Administrator Password The Router ships with NO password entered If you wish to add a password for more security you can set a password here Keep your password in a safe place as you will need this password if you need to log into the Router in the fu
4. Wireless and Network From there select Wi Fi to see the list of available networks Select your wireless network from the list If asked to do so enter your network password Windows 7 Your computer provides a menu of available wireless networks at the right end of the task bar Right click on the icon that looks like signal strength bars Select your wireless network from the list If asked enter your network password network key Windows Vista and Windows XP Your device provides a menu of available wireless networks at the right end of the task bar Right click on the icon that shows a computer with wireless waves XP or two computers Windows Vista cq Choose View Available Wireless Networks XP or Connect to a network Vista from the menu Select your wireless network from the list If asked enter your network password network key GETTING TO KNOW YOUR ROUTER Front Panel Your Router s status is shown by the lights on the front panel Power Light Off The Router is not plugged into a power source Solid Green Power is supplied to the Router WLAN Light Off WLAN is disabled Blinking Green Wireless data is being transmitted in the WLAN Solid Green WLAN is enabled but no data transfer Wi Fi Protected Setup WPS Light Off Idle Blinking Green The Router is listening for a WPS enabled computer or other device Successful Connection The WPS li
5. Utilities gt Restore Previous Saved Settings This Option will allow you to restore a previously Saved configuration C Documents and Settings AdmunistratoriDe sil Browse Chagas file AD biy Fini Damei Ej Criit upip Flinn fi A 5 Tie of tyga ET Microsoft Internet Explorer 2 Do you mark to continue and restore settings 30 USING YOUR ROUTER A prompt asking Do you want to continue and restore settings will appear Click OK and then the Router begins to restore the previous settings The previous settings have been restored successfully Enabling Auto Firmware Update for Your Router The Router has the capability to automatically check for a newer version of firmware and alert you when it s available You can choose to download the new version or ignore it By default this feature is enabled Note We recommend you use a computer that has a wired connection to the Router Setup Steps Router is rebooting 38 seconds remaining Click on System Settings in the left hand column under the Utilities heading Toward the lower half side of the screen you will find Auto Update Firmware Enabling Select the Enable radio button Click Apply Changes Utilities Restart Router Restore Factory Defaults Save Backup Settings Restore Previous Settings Firmware Update System Settings Self Healing Auto Update Firmware Enabling ADVANCED FEA
6. automatically assigning IP addresses to comupters in the LAN Users do not need to configure TCP IP protocol paramters such as the IP address the subnet mask the gateway and the DNS server information for computers connected to the Router s LAN Setup steps Open a Web browser on the computer In the address bar of the Web browser type http 192 168 2 1 3 belkin Router Setup Home Help Login Click Login in the upper right corner of the page The Router does not ship with a password so just click Submit DHCP Client List Click on LAN Settings in the left column under the LAN Setup heading P fed Gling Atn P Foa Latag Acorens gt Select the On button to use the Router as a DHCP server Configure the parameters below IP Pool Starting Address IP Pool Ending Address Set the starting and ending IP addresses to specify a pool of IP addresses to be assigned by the DHCP server After you set Starting IP Address Ending IP Address hosts in the LAN obtain IP addresses that are in the range of the starting and ending IP addresses 15 USING YOUR ROUTER Lease Time The valid time for an IP address that is automatically assigned to a device by the DHCP server to a host The DHCP server does not assign the IP address to other hosts within the specified time If selecting Forever you save devices in the LAN with fixed addresses Configuring the Local Domain N
7. the Router s wireless network Please refer to Adding Computers to Your Network in this manual for instructions 40 TROUBLESHOOTING SUPPORT AND WARRANTY can t connect to the Internet wirelessly and my network name is not listed in Available Networks 1 Verify that your Router is on and the front panel light shows solid green 2 If you are far from the Router you might try moving closer to see if you might have been out of range 3 Using a computer attached to the Router via a network cable visit http router and ensure that Broadcast SSID is ON This setting is found on the Channel and SSID page My wireless network performance is slow inconsistent suffers from weak signal or I m having difficulty maintaining a VPN connection Wireless technology is radio based which means connectivity and the throughput performance between devices decreases when the distance between devices increases Other factors that will cause signal degradation metal is generally the worst culprit are obstructions such as walls and metal appliances Note also that connection speed may decrease as you move farther away from the Router In order to determine if wireless issues are related to range we suggest temporarily moving the computer within 10 feet from the Router if possible Changing the wireless channel Depending on local wireless traffic and interference switching the wireless channel of your netw
8. 33 35 20 00 www belkin com de networking www belkin com nl networking www belkin com fr networking www belkin com uk networking www belkin com uk networking www belkin com uk networking www belkin com fr networking www belkin com de networking www belkin com uk networking www belkin com uk networking www belkin com uk networking www belkin com uk networking www belkin com it networking www belkin com uk networking www belkin com nl networking www belkin com uk networking www belkin com uk networking www belkin com uk networking www belkin com networking www belkin com networking www belkin com networking www belkin com uk networking www belkin com es networking www belkin com uk networking www belkin com de networking www belkin com fr networking www belkin com uk networking 44 TROUBLESHOOTING SUPPORT AND WARRANTY Belkin International Inc Limited 2 Year Product Warranty What this warranty covers Belkin International Inc Belkin warrants to the original purchaser of this Belkin product that the product shall be free of defects in design assembly material or workmanship What the period of coverage is Belkin warrants the Belkin product for two years What will we do to correct problems Product Warranty Belkin will repair or replace at its option any defective product free of charge except for shipping charges for the product Belkin reserves the right
9. C address and will allow the connection to work If you are not sure if your ISP needs to see the original MAC address simply clone the MAC address of the computer that was originally connected to the modem Cloning the address will not cause any problems with your network To Clone your MAC address make sure that you are using the computer which was ORIGINALLY CONNECTED to your modem before the Router was installed Click the Clone button and click Apply Changes Your MAC address is now cloned to the Router 22 USING YOUR ROUTER Enabling Website Filtering The Router allows you to restrict website access to guard you from unsafe and inappropriate websites on any devices on your network Parental Controls gt Website Filters Provides a frst kayan of whole Nome intermet protecton fo guard you Pon ungate ang 7 ape coriste mabs os on any Space OF our Network Filtering Opbons gt Bock Madonos AAS and other non family Inendy Sees togs malame DISTT and Scam sies and ASD saan Tat Contam penalty epici material Mataro content fom sicohel Decco cime cull drugs gaming Nata suicide or vicience Bock Maca araf Akit Shee Mods malware phishing scam pips anc nian Tit Contam saia egct content Bock Matos Sites Hows maiya panang 3853 Icam pitie Configuring Basic Wireless Settings You can view and specify the wireless security settings of your Router Setup steps Open a Web browser on the computer
10. N 1 5 ips HOME NETWORK User Manual Ig gt Q amp A m IN TABLE OF CONTENTS GETTING STARTED 222220244355 nI EEEE REEE e E EEE a a 1 What sh Ne BOX au sad ee ee bis Ea inten Mig et le 1 WM AS OVO aa o Sassi Ng BANGKA AG BE AG toca Pe th vale wed Meader edie 1 Howto Sett UP sas ita ee tata ON dite LG seh ck A a edt ats 2 Adding Computers to Your Network 00e aa 3 Manually Set Up Your Internet Connection 4 GETTING TO KNOW YOUR ROUTER 10 Front Paneles cerises aaea PAA 10 Back Paneliti itra a t a a a eee SE a a ae TA 11 Technical Details ssizasssssepsessasa sa db Spade ds 12 Technical FORNOS aaa RES SD NA AA RG E 12 System RequirementsS 0 00 cece eee cera 13 USING YOUR ROUTER paanakin eres 14 Using the LAN IP Setup ese screen so aan bree ete Wee es 14 Configuring Your Internet Connection 00 cece eee 16 Cloning your MAC address 000 cece cence tenes 22 Enabling Website Filtering 02 e ee eee ees 23 Configuring Basic Wireless Settings 23 Restarting Your Router 0 04 sa kaaa kana Ah ieee a E news 25 Restoring Your Router to Factory Defaults 26 Backing Up Your Configuration cee eee 27 Restoring Previous Settings 0 0 e eee eee 29 Enabling Auto Firmware Update for Your Router 31 Updating the Router s Firmware cece eee eee 32 Conf
11. NTP server If you reside in an area that observes Daylight Saving then place a checkmark in the box next to Daylight Savings Click Apply Changes Time and Time Zone January 01 2011 9 54 47 PM The Router ships with NO password entered If you wish to add a password for more security you can set a password here More Info Time Zone gt GMT 08 00 Pacific Time Tijuana Daylight Savings gt Automatically Adjust Daylight Saving Primary NTP Server gt 192 43 244 18 North America Secondary NTP Server gt 132 163 4 102 North America 36 USING YOUR ROUTER Configuring Remote Management Remote management allows you to make changes to your Router s settings from anywhere on the Internet Before you enable this function make sure you have set the administrator password Setup Steps Utilities Restart Router Restore Factory Defaults Save Backup Settings Restore Previous Settings Firmware Update System Settings Self Healin Click on System Settings in the left hand column under the Utilities heading If you select the Any IP address can remotely manage the router check box you are allowed to access the Router from anywhere on the Internet by typing in your WAN IP address from any computer on the Internet If you do not select the Any IP address can remotely manage the router check box specify an IP address to remotely manage
12. Protocol over Ethernet as the connection type If you use a DSL modem to connect to the Internet your ISP may use PPPoE to log you into the service Setup steps Click Connection Type in the left column under the Internet WAN heading Select PPPoE in the Connection Type page that appears WAN gt Connection Type gt PPPoE ter your PPPOE setings type in your information below and click Apply changes More Info User Nama gt Password gt Retype Password gt Service Name Optional gt IP assigned by ISP gt YES IP Ackiress gt MTU 500 1500 gt 454 12 Anen 1454 More info More info 19 USING YOUR ROUTER Configure the parameters below User Name and Password Enter the user name and password provided by the ISP The user name and password are used to log in to the ISP server Retype Password Enter the password again Service Name If several PPPoE servers are available specify which server to use IP assigned by ISP You can select either to an IP address assigned by your ISP or to manually set an IP address in the IP Address field MTU The maximum transmission unit We strongly recommend you to use the default setting unless your ISP gives you a specific MTU setting If you select the Disconnect after xxx minutes of no activity check box and specify a time interval the system interrupts the Internet connection when there is no Internet
13. TURE Allows you to automatically check the availability of firmware updates for your router More Info Auto Update Firmware Enable Disable gt Enable Disable 31 USING YOUR ROUTER Updating the Router s Firmware The following steps show you how to update your Router s firmware using its Web interface Checking for New Firmware in the Firmware Upgrade Screen N150 Router allows you to check for a new firmware update available for this Router Setup steps Utilities Restart Router Restore Factory Defaults Save Backup Settings Restore Previous Settings rrmware Update System Settings Self Healing Click on Firmware Update in the left hand column under the Utilities heading Click Check Firmware to check for new firmware versions If a new version is found you can directly update your firmware by following the prompts Firmware Version gt F9K1009 YY 100 0 Check For New Firmware Version 3 d Check Firmware D Update Firmware gt Browse Update 32 USING YOUR ROUTER Updating Manually to New Router Firmware You can also manually update your Router firmware Setup Steps Locate and download the firmware file from the Belkin support site Type your part number into the search box in the top right corner and look for Firmware in the title Save the file to a location on your computer where you can get to it easily such a
14. access behavior within the specified time Click Apply Changes If after a few minutes your Internet Status says Connected you re done You can surf the Internet PPTP L2TP Connection Some ISPs require a connection using the PPTP or L2TP protocol Enter the account and password provided by your ISP The following takes PPTP connection as an example Setup steps Click Connection Type in the left column under the Internet WAN heading Select PPTP in the Connection Type page that appears WAN gt Connection Type gt PPTP 20 USING YOUR ROUTER Configure the parameters below PPTP Account and PPTP Password Enter the PPTP account and password provided by the ISP The PPTP account and password are used to log in to the ISP server Retype Password Enter the password again Host Name Optional Enter the host name Service Address Enter the IP address of the ISP server IP Address Assignment You can select either to dynamically get an IP address from the ISP or to use a static IP address If you select Use Static IP Address manually enter the IP address the subnet mask and the default gateway C Disconnect after 5 minutes of no activity More Info If you select the Disconnect after xxx minutes of no activity check box and specify a time interval the system interrupts the Internet connection when there is no Internet access behavior within the speci
15. ame The local domain name is a user friendly name for your Router At the bottom of the LAN Settings page you can set a local domain name The default name is Belkin There is no need to change this setting unless required Local Domain Name gt Belkin Optional A feature that lets you assign a name to your network More Info Configuring Your Internet Connection Settings related to your Internet service are specified in the Connection Type page under the Internet WAN heading Select a WAN connection type Contact your ISP if you do not know your WAN connection mode Dynamic Connection Cable and fiber customers generally require a dynamic connection Setup steps Click Connection Type in the left column under the Internet WAN heading WAN gt Connection Type Dhima Theri Bapor ipar i amip 16 USING YOUR ROUTER Select Dynamic in the Connection Type page that appears Click Next WAN gt Connection Type gt Dynamic IP To enter your Dynamic IP settings type in your information below and click Apply changes More Info Host Name A name that some Internet Service Providers require for connection to their system Change WAN MAC Address 17 Enter the host name provided by your Internet provider Click Apply Changes Internet Status Connected USING YOUR ROUTER If after a few minutes your Internet Status says Conne
16. bled device you d like to add to your network GETTING STARTED Manually Set Up Your Internet Connection y p You can also try visiting http 192 168 2 1 Use a browser to visit http Router The Router homepage should appear http router Internet Status Connected GETTING STARTED The status of your Internet connection is shown in the upper right corner of the Router homepage If after a few moments it says Connected you re done You can surf the Internet Internet WAN Connection Type DNS MAC Address erental Controls If not select Connection Type from the menu on the left LE belkin Router Setup Login Before pou can change amy seling pow need bo bag in mih a pagawond E pow hae nol yel sala orlom pasword internet WAN bhen heave thes bald blank and dick Submil Password Dilmi kako blank Paremini Com rods co is GETTING STARTED If a password screen appears press Submit WAN gt Connection Type Select your connection type Dynamic A Dynamic type of connection is the most common If you use a cable modem then most likely you will have a dynamic connection If you have a cable modem or you are not sure of your connection type use this Static A Static IP address connection type is less common than others Use this selection only if your ISP gave you an IP address that never changes PPPoE lf you use a DSL modem and or y
17. cted you re done You can surf the Internet Static Connection Select Static IP if your ISP provides the IP address subnet mask and information about the gateway and DNS server Setup steps Click Connection Type in the left column under the Internet WAN heading Select Static in the Connection Type page that appears WAN gt Connection Type gt Static IP es More Into IP Address gt Subnet Mask gt ISP Galaway Address gt Configure the parameters below These parameters cannot be left blank IP Address Enter the WAN IP address provided by the ISP The parameter must be entered Subnet Mask Enter the WAN subnet mask provided by the ISP It varies with the network type It is usually 255 255 255 0 Class C ISP Gateway Address Enter the IP address of the gateway provided by the ISP It is the IP address used for connecting to the ISP 18 USING YOUR ROUTER Click Click here to enter your DNS Settings to configure DNS information Clear the Automatic from ISP check box In the DNS Address and Secondary DNS Address fields enter the IP addresses of the primary DNS server and the secondary server if available At least enter one DNS server IP address Click Apply Changes If after a few minutes your Internet Status says Connected you re done You can surf the Internet PPPoE Connection Most DSL providers use PPPoE Point to Point
18. de Off If you are operating in an environment with HEAVY 802 11b traffic or interference best performance may be achieved with Protected Mode On The default 802 11e WMM QoS mode is On QoS prioritizes important data on your network such as multimedia content and voice over IP VoIP so it will not be interfered by other data being sent over the network Click Apply Changes 24 USING YOUR ROUTER Restarting Your Router Sometimes in order to make some changes take effect you need to restart the Router Setup Steps Utilities Restart Router Click on Restart Router in the left hand column under the Utilities heading Click on the Restart Router button toward the middle of screen Microsol Internet Explorer Y Are you sure you want to restart the Router Restarting the Router mil not affect your configuration A dialog box appears to ask you whether to restart the Router Click the OK button to restart the Router Router is rebooting seconds remaining After clicking the OK button the Router begins to restart 25 USING YOUR ROUTER Restoring Your Router to Factory Defaults Resetting the Router will restore the Router s normal operation while maintaining the programmed settings Reset the Router in rare cases when the Router may function improperly Using the Reset Button Use the restore option in instances where you may have forgotten your cus
19. e type then click the Save button When the download process is complete click Close Your Router s configurations have been successfully saved to your local PC Domload complete ih Download Completo Kage water coord frome DALIG E Coss hm dudog boo Kahan doers pamplinag Gen Opened Restoring Previous Settings Sometimes you need to restore the previous settings This may be because the Router is not performing as expected or you wish to remove all current settings Setup Steps Utilities Restart Router Restore Factory Defaults Save Dackup Settings restore Previous Settings Firmware Update System Settings Self Healing 29 USING YOUR ROUTER Click on Restore Previous Settings in the left hand column under the Utilities heading Click the Browse button toward the middle of the screen to search for the file you saved previously Note The version of configuration file in the images below is depicted as an example Your file name will vary depending on your model and version Utilities gt Restore Previous Saved Settings This option will allow you to restore a previously saved configuration Browse D Restore Select the configuration file by left clicking on it and then click the Open button in the lower right corner of the window This will take you back into the Router s interface Click the Restore button
20. elkin product b Where you purchased the product c When you purchased the product d Copy of original receipt 2 Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim Belkin reserves the right to review the damaged Belkin product All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser If Belkin determines in its sole discretion that it is impractical to ship the damaged equipment to Belkin Belkin may designate in its sole discretion an equipment repair facility to inspect and estimate the cost to repair such equipment The cost if any of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser Damaged equipment must remain available for inspection until the claim is finalized Whenever claims are settled Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have 46 REGULATORY INFORMATION European Compliance Statement Belkin International hereby declares that this F9K1009 Wireless N Router is in compliance with the essential requirements and other revelant provisions of the RTT amp E Directive 1999 5 EC the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 5 EC Conformity was assessed using a Technical Construction File A copy of the European Union CE ma
21. et If these steps do not work try restarting your modem and repeating the process If not we ll try a PPPoE connection next Internet Status Connected O WAN gt Connection Type Select your connection type Dynamic A Dynamic type of connection is the most common If you use a cable modem then most likely you will have 3 dynamic connection If you Nave a cable modem r you are nal Sure of your Connection type use Mis Static A Static IP address connection type is less common than others Use this selection only f your ISP gave you an IP address that newer changes PPPoE if you use a OSL modem and or your ISP gave you a User Name and Password then your connection type is PPPoE Use this connection type PPIP European Counties Only This type of connection is most common in European counines E your ISP has specifically told you that you use PPTP and has supplied you with the proper PPTP information Men use this option L2TP European Countnes Only This type of connection is most common in European counties E your ISP has specifically told you thal you use L2TP and has supplied you with the proper LATP information then use this apSon Telstra Bigpond OptusNet Cable Use this aption for Bigpond Cable and OptusNet Cable connections only ma GETTING STARTED PPPoE Connection Enter the username and password supplied by your Internet provider and click Apply Changes Ignore the other fie
22. fied time Click here to enter your DNS Settings Clear Changes Apply Changes WAN gt DNS lf your ISP provided you with a specific DNS address to use enter the address in this window and click Apply Changes C Automatic from ISP DNS Address gt 192 168 123 3 sa a a DNS Domain Name Server A server located on the Internet that translates URL s Uniform Resource Locator like www belkin com to IP addresses You must enter the DNS settings provided by your ISP if you don t use the Automatic DNS function More info Secondary DNS Address gt Clear Changes Apply Changes 21 USING YOUR ROUTER Click Click here to enter your DNS Settings to configure DNS information Either select or clear the Automatic from ISP check box If you clear the check box in the DNS Address and Secondary DNS Address fields enter the IP addresses of the primary DNS server and the secondary server if available At least enter one DNS server IP address Click Apply Changes If after a few minutes your Internet Status says Connected you re done You can surf the Internet Telstra Bigpond OptusNet Cable Use this option for Bigpond Cable and OptusNet Cable connections only Cloning your MAC address Belkin provides the ability to clone copy the MAC address of the computer into the Router This MAC address in turn will be seen by the ISP s system as the original MA
23. ght is SOLID GREEN for 5 minutes and then goes out when the Router has made a secure connection with the computer or other device Failed Connection The WPS light is BLINKING GREEN for 30s after the WPS connection fails WAN Light Off WAN connection is not created Blinking Green Data is being transmitted on the WAN port Solid Green The Router is connected to the Internet LAN Light Off LAN connection is not created Blinking Green Data is being transmitted on the LAN port Solid Green The Router is connected to devices through Ethernet cables 10 GETTING TO KNOW YOUR ROUTER Back Panel Reset Button This button is used to restore the factory default settings To reset the Router press and hold this button for 8 10 seconds Power Connector Connect the included power supply to this jack Modem WAN Connector Connect your modem to this port using an Ethernet cable Wired LAN Connectors Connect computers and other wired network device to these ports using Ethernet cables WPS Button The WPS button on the back of your Router can be used to help establish a secure connection between your Router and other WPS enabled Wi Fi devices such as computers To use the WPS feature on your Router see Getting Started gt Adding Computers to Your Network gt Using the WPS Button 11 TECHNICAL DETAILS Technical Features Integrated 802 11n Wireless Access Point The N150 technol
24. iguring Administrator Password 000 cece nee eee 35 Configuring Time ZONG 44 pans ANG vane dss eu Ewe ean Ped eRe 36 Configuring Remote Management a 37 Configuring NG ada AA AA PAA 38 Configuring the Eco Mode a 38 Configuring Self Healing a 39 Troubleshooting Support and Warranty 40 Troubleshooting kaaa tip AANGAL kaa Ted be bb ham ha 40 Belkin International Inc Limited 2 Year Product Warranty 0c eee ee eee eee ee 45 Regulatory Information 00 022 e eee eee ee eee 47 European Compliance Statement eee eee ees 47 General Safety Information 00 ccc eee ee 47 GETTING STARTED What s in the Box N150 Wireless Router Ethernet cable Power supply Belkin CD with User Manual Quick Installation Guide Service Card Initial Setup Where to Place Your Router For the best results place the Router next to your modem in an open location away from large metal objects and magnets such as those found in speakers Raising the Router above floor level can improve the strength of your wireless signal GETTING STARTED 3 Power up your modem by plugging in its power supply How to Set It UP do 4 Power up your Router by plugging in its power supply Connect Your N150 Router 1 Turn off your modem by disconnecting its power supply 2 Connect your Router to your modem using the cable 3 k NG
25. lds Some DSL customers require a PPPoE connection Select PPPoE this time and press Next WAN gt Connection Type gt PPPoE Internet Status Connected To enter your PPPoE settings type in your information below and click Apply changes More Info User Name gt fo Password gt Retype Password gt Service Name Optional gt Doo IP assigned by ISP gt MTU 500 1500 gt Do not make changes to the MTU setting unless your ISP specifically requires a different setting than 1454 More Info C Disconnect after 5 minutes of no activity More Info ___Car Changes Apply Changes GETTING STARTED If after a few minutes your Internet Status says Connected you re done You can surf the Internet If these steps do not work try restarting your modem and repeating the process Connecting Additional Devices iOS iphone iPad and iPod touch Open the Settings app and select the Wi Fi menu item Select your wireless network from the list that appears there If asked to do so enter the network password Mac OS X Your Mac provides a menu of available wireless networks at the right end of the menu bar Click on the icon showing wireless waves Select your wireless network from the list that appears there If asked to do so enter the network password Android phones and tablets 4 Open the Settings app and select
26. ogy enhances your Router s wire less capabilities allowing for data transfer speeds of up to 150Mbps across your network NAT IP Address Sharing To save you the cost of adding IP addresses per com puter in your house your Belkin Router uses Network Address Translation NAT technology allowing you to share a single IP address across your network SPI Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common attacks and viruses Universal Plug and Play UPnP Compatibility The UPnP Universal Plug and Play feature in your Router offers seamless operation of voice and video messaging games and other applications that are UPnP compliant Web Based Advanced User Interface You can easily make changes to your Router s ad vanced settings through your web browser These changes can be made from any computer on your network Integrated 4 Port 10 100 Switch Your Router has a built in 4 port network switch to al low your wired computers to share printers data MP3 files digital photos and much more TECHNICAL DETAILS System Requirements Router Broadband Internet connection such as a cable or DSL modem with RJ45 Ethernet connection At least one computer with an installed network interface adapter TCP IP networking protocol installed on each computer RJ45 Ethernet networking cable Internet browser 13 USING YOUR ROUTER Using the LAN IP Set
27. onnect wirelessly to your Router You will need to find the network settings on your client select the network name printed on the card from the list of available networks and enter the password when prompted to join the wireless network 42 TROUBLESHOOTING SUPPORT AND WARRANTY Does the Router support Wireless Protected Access WPA security The Router ships with WPA WPA2 security turned on Windows XP and some older network hardware may require a software update to support WPA WPA2 am having difficulty setting up WPA security on my Router 1 Log in to your Router by visiting http router with your web browser Click on the Login button in the top right hand corner of the screen You will be asked to enter your password If you have never set a password leave the Password field blank and click Submit 2 Click Wireless in the left hand menu Then click Security just below that 3 Select the WPA WPA2 option 4 Enter a password This can be from 8 63 characters of your choice including spaces and punctuation OR a 64 digit hexadecimal number using only the numbers 0 9 and letters A F 5 Click Apply Changes to finish Your wireless connection is now encrypted Each computer using your wireless network will need to use the new key Note If you are configuring the Router over a wireless connection you will have to re connect to the Router after changing any securi
28. ork can improve performance and reliability See the section titled Changing the Wireless Channel for instructions on how to choose other channels 41 TROUBLESHOOTING SUPPORT AND WARRANTY Limiting the wireless transmit rate Limiting the wireless transmit rate can help improve range and connection stability Most wireless cards have the ability to limit the transmission rate To change this property in Windows go to the Windows Control Panel open Network Connections and double click on your wireless card s connection In the properties dialog select the Configure button on the General tab then choose the Advanced tab and select the rate property Wireless client cards are usually set to automatically adjust the wireless transmit rate for you but doing so can cause periodic disconnects when the wireless signal is too weak as a rule slower transmission rates are more stable Experiment with different connection rates until you find the best one for your environment Note that all available transmission rates should be acceptable for browsing the Internet For more assistance see your wireless card s user manual I ve installed this new Router and some of my network clients computers game consoles etc are now unable to connect Your new Router came pre configured with a network name and password found printed on an attached card All clients must use this network name and password to c
29. our ISP gave you a User Name and Password then your connection type is PPPoE Use this connection type PPTP European Countries Only This type of connection is most common in European countries If your ISP has specifically told you that you use PPTP and has supplied you with the proper PPTP information then use this option L2TP European Countries Only This type of connection is most common in European countries If your ISP has specifically told you that you use L2TP and has supplied you with the proper L2TP information then use this option Telstra Bigpond OptusNet Cable Use this option for Bigpond Cable and OptusNet Cable connections only Net Dynamic Connection Cable and fiber customers generally require a dynamic connection Some DSL customers require a PPPoE connection Let s try dynamic first Select Dynamic from the menu that appears and press Next WAN gt Connection Type gt Dynamic IP To enter your Dynamic IP settings type in your information below and click Apply changes More Info Host Name gt Host Name Aname that some Internet Service Providers require for connection to their system Change WAN MAC Address Cancel Changes Apply Changes GETTING STARTED Enter the host name provided by your Internet If after a few minutes your Internet Status says service provider Click Apply Changes Connected you re done You can surf the Intern
30. rking Declaration of Conformity may be obtained at the website www belkin com doc CED For information on product disposal please refer to http environmental belkin com Es General Safety Information e For indoor installation only e For installation with supplied power adapter only e The supplied power adapter is the product s switch off device The base socket must be near the product and easily accessible 47 belkin com 2012 Belkin International Inc All rights reserved All trade names are registered trademarks of respective manufacturers listed Mac Mac OS and Safari are trademarks of Apple Inc registered in the U S and other countries Windows Windows Vista Internet Explorer and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries F9K1009_8820ed01125_uk Belkin Ltd Express Business Park Shipton Way Rushden NN10 6GL United Kingdom Belkin Iberia Avda de Barajas 24 Edificio Gamma 4 pta 28108 Alcobendas Madrid Spain Belkin SAS 130 rue de Silly 92100 Boulogne Billancourt France Belkin Italy amp Greece Via Nino Bonnet 4 6 Milan 20154 Italy Belkin GmbH Otto Hahn StraBe 20 85609 Aschheim Germany Belkin B V Tupoleviaan 1 1119 NW Schiphol Rijk Netherlands
31. s your desktop Connect the computer to one of the four LAN ports on the Router Open a web browser on the computer In the address bar of the web browser type http 192 168 2 1 and press Enter on your keyboard Click Login in the upper right hand corner of the page The Router does not ship with a password so just click Submit Click on Firmware Update in the left hand column under the Utilities heading Utilities Restart Router Restore Factory Defaults Backup Settings Restore Previous Settings rirtmvare Update System Settings Self Healing utilities Firmware Update Emma fires Do irha bislbin moy release r improvermente and tenes be prohtemoe that may hayo osictod Click Hie li UPON GR Gb for ihe subir tiia PT Bee Ee LO rr ri ret bernard od lee k bobos tie geo dfihora Seana ie a mas BIT DT MOTE Please backup Four dumani seins before updabng lo fr version GT rire are Click Noo bs go to ma up cure ng Dare mc Hinga pag Pee Nag mas a PASA TEH AAP AG E Check Por Hee Pinaasa a fad ain Check Kamera ba Relate Flea Lineetaene 33 USING YOUR ROUTER Click the Browse button toward the middle of the screen to search for the file you saved previously Note The firmware version in the images below is depicted as an example Your file name will vary depending on your model and version Choose file Look in
32. the Router Note Selecting Only this IP address can remotely manage the router is more secure but less convenient In the Remote Access Port field set the port number for accessing the router through remote Web management Click Apply Changes Remote Management ADVANCED FEATURE Remote management allows you to make changes to your Router s settings from anywhere on the Internet Before you enable this function MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD More Info C Any IP address can remotely manage the router Only this IP address can remotely manage the router Remote Access Port gt pi 37 USING YOUR ROUTER Configuring the Eco Mode Configuring UPnP This function allows you to dim the LEDs on the front of the Router to UPnP Universal Plug and Play offers seamless save power and disable the wireless radio at predetermined times operation of voice messaging video messaging games and other applications that are UPnP compliant Setup Steps The Router ships with the UPnP feature enabled If you are using any applications that are UPnP compliant and wish to take Click on System Settings in the left hand advantage of the UPnP features you can enable the UPnP feature column under the Utilities heading Utilities Restart Router UPnP Enabling ADVANCED FEATURE Allows you to turn the UPnP feature of the Router on or off If you use applica
33. tions that support UPnP enabling UPnP will allow these applications to automatically configure the router More Info UPnP Enable Disable gt Enable O Disable Self Healing 38 USING YOUR ROUTER Select the Disable radio from to enable the Eco mode Click on Self Healing in the left hand column under the Utilities heading Specify the days you want to use the Eco mode Select the Enabled radio button to enable Click Apply Changes automatically initialization for your Router Specify the days and the time for automatically initialization Configuring Self Healing iek Apply Changes The self healing function allows the Router to implement regular restart reducing equipment function failure You can arrange a schedule for Router s auto initialization Setup Steps Health gt Regular Maintenance Utilities ce then sie Leas Regular router re initialization is helpful in maintaining a more problem free network Restart Router Auto initialize my router gt G Enabled Disabled Set days gt I sun I MON F TUE T WED I THU I FRI I sat 03 30 AM x Clear Changes Apply Changes Restore Factory De Set time gt 39 TROUBLESHOOTING SUPPORT AND WARRANTY Troubleshooting can t connect to the Internet wirelessly If the light on the front of the Router is solid green then your Router is connected to the Internet You may not be connected to
34. to discontinue any of its products without notice and disclaims any limited warranty to repair or replace any such discontinued products In the event that Belkin is unable to repair or replace the product for example because it has been discontinued Belkin will offer either a refund or a credit toward the purchase of another product from Belkin com in an amount equal to the purchase price of the product as evidenced on the Original purchase receipt as discounted by its natural use What is not covered by this warranty All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin s request at the sole expense of the purchaser or if Belkin determines that the Belkin product has been improperly installed altered in any way or tampered with The Belkin Product Warranty does not protect against acts of God such as flood lightning earthquake war vandalism theft normal use wear and tear erosion depletion obsolescence abuse damage due to low voltage disturbances i e brownouts or sags non authorized program or system equipment modification or alteration 45 TROUBLESHOOTING SUPPORT AND WARRANTY How to get service To get service for your Belkin product you must take the following steps 1 Contact Belkin Tech Support at the number listed on page 44 within 15 days of the Occurrence Be prepared to provide the following information a The part number of the B
35. tom password or when the Router may function improperly Push and hold the Reset button for 8 10 seconds and then release it The LAN light on the Router will momentarily flash and the WLAN light will turn out When the LAN and WLAN lights become solid green again the reset is complete Restoring the Router to Default Settings Using the Web Interface You can also restore the factory defaults using the web interface This may be because the Router is not performing as expected or you wish to remove all previously configured settings Setup Steps Click on Restore Factory Defaults in the left hand column under the Utilities heading Utilities Restart Router Restore Factory Defaults Save Backup Settings Restore Previous Settings Firmware Update System Settings Self Healing Unites gt Aesiora Factory Detecta 26 USING YOUR ROUTER Click on the Restore Defaults button A warning box will open that says Warning All your settings will be lost Are you sure you want to do this Click OK The Router will begin the restoration process Once the restoration process is complete the Router will reboot Note This may take several minutes Your Router has been successfully restored to its factory settings Microsoft Internet Explorer 2 WARNING All Your Settings Will be Lost 4re You Sure You want ko do this Backing Up Your Configuration The configuration se
36. ttings of the Router are stored within the Router in a configuration file You can back up save the file and retrieve it for later use We recommend that you back up your configuration file after you complete settings If the Router fails or becomes corrupted or an administrator password is lost you can easily re obtain your configuration by restoring the configuration file Setup Steps Utilities Restart Router Restore Factory Defaults save Backup Settings Restore Previous Settings irmware Update tings 27 USING YOUR ROUTER Click on Save Backup Settings in the left hand column under the Utilities heading Click on the Save button Ubites fae Bechup Cyerent Salting fe eee pour Seo ET pete E pe Reh iban poe E erie ast wia SG rd jid elgg arm bos AA EE Pee oss bie Pear ver jar ced i a kee ee el Hile Download Do you want to open a seve thes file a Name user conf Tyee HIM Documerk Frome 192 168 2 1 Open Swe Canc A Wide Glee hom the Internet can be utab sorte kisa can polartully ham your Comguder I pou do rot busi he souon do nol open ot sarve thes tke wha y thee nigh A dialog box will open that says Do you want to open or save this file Click Save Semi G Ort LJM Deca mario 14 nee Cita etext Paces 28 USING YOUR ROUTER Select the location for saving the configuration file Enter the file name and select the fil
37. ture It is also recommended that you set a password if you plan to use the remote management feature of this Router Setup Steps Utilities Restart Router Restore Factory Defaults SavelMDackup Settings Restore Previous Settings Firmware Update System Settings Self Healing Click on System Settings in the left hand column under the Utilities heading Configuring the administrator password and login timeout Click Apply Changes Utilities gt System Settings Alin aor Passion ik Tha Router ahipa wih MO pasa prisepd Hi yo wish io mad a pend for Pera Daruri you Can sot a Pe here hore lr Tree inam Parii Tape inner Pariwo Camiini nem Passed Login Timea ig 1 94 minutes 35 USING YOUR ROUTER Configuring Time Zone The Router keeps time by connecting to a Simple Network Time Protocol SNTP server This allows the Router to synchronize the system clock to the global Internet The synchronized clock in the Router is used to record the security log and control client filtering Select the time zone that you reside in The system clock may not update immediately Setup Steps Utilities Restart Router Restore Factory Defaults SaveMDackup Settings Restore Previous Settings Firmware Update System Settings Self Healing Click on System Settings in the left hand column under the Utilities heading Select the time zone that you reside in and the
38. ty settings Note Some older networking hardware supports only WEP encryption If your older computers cannot connect to your network try 128 bit or 64 bit WEP or seek software updates from their manufacturers 43 TROUBLESHOOTING SUPPORT AND WARRANTY Technical Support US http www belkin com support UK http www belkin com uk support Australia http www belkin com au support New Zealand http www belkin com au support Singapore 1800 622 1130 Europe http www belkin com uk support You can find technical support information on our website www belkin com by navigating to the tech support section If you want to contact technical support by phone please call the number you need from this list Local rates apply AUSTRIA BELGIUM CZECH REPUBLIC DENMARK FINLAND FRANCE GERMANY GREECE HUNGARY ICELAND IRELAND ITALY LUXEMBOURG NETHERLANDS NORWAY POLAND PORTUGAL RUSSIA SLOVAKIA SLOVENIA SOUTH AFRICA SPAIN SWEDEN SWITZERLAND UNITED KINGDOM OTHER COUNTRIES 0820 200766 07 07 00 073 239 000 406 701 22 403 0972519123 08 25 54 00 26 0180 500 57 09 00800 44 14 23 90 06 17 77 49 06 800 8534 0818 55 50 06 02 69 43 02 51 34 20 80 85 60 0900 040 07 90 0 10 per minute 81 50 0287 00800 441 17 37 707 200 676 495 580 9541 08000 04614 0800 80510 0800 99 15 21 902 02 43 66 07 71 400453 08 48 00 02 19 0845 607 77 87 44 19
39. up The LAN Settings page allows changing the Router s LAN IP address as required and configuring Dynamic Host Configuration Protocol DHCP Configuring Parameters of LAN IP Setup LAN IP setup parameters are advanced settings that you may require if you are a network administrator or your network requires a different IP addressing scheme The Router is shipped with the default IP address on the LAN side and with the DHCP server enabled Note If you change the default LAN IP address you must use the new LAN IP address to log in Setup steps Open a Web browser on the computer In the address bar of the Web browser type http 192 168 2 1 belkin Router Setup Home Help Login Click Login in the upper right corner of the page The Router does not ship with a password so just click Submit DHCP Client List Click on LAN Settings in the left column under the LAN Setup heading IP Address gt 192 168 2 1 More Info Subnet Mask gt More Info 255 255 0 USING YOUR ROUTER Configure the IP address and subnet mask IP Address The IP address that a LAN user uses to access the Router The default IP is 192 168 2 1 IP Subnet Mask Subnet mask of the LAN port You can enter a different subnet mask according to the actual network status Click Apply Using the Router as a DHCP Server By default the Router acts as a DHCP server
Download Pdf Manuals
Related Search
Related Contents
OM, BZ27, BZ34, 2006-05 Observer via une visite virtuelle (Street View) des éléments distants Franke Consumer Products FRC05 User's Manual Tecumseh AEA9415ZXCSS Technical Data Sheet ダウンロード OPTION KIT PDF(生産終了品) PDF版 - 大塚硝子 Hewlett Packard Enterprise 10508-V Et si j`osais ! Digitus DN-94015 Copyright © All rights reserved.
Failed to retrieve file