Lynx Quick Start
Contents
1. i BS F N LOCAL SOUNDER DISABLE JUMPER CUT DISABLE ALL OUTPUT CIRCUITS ARE POWER LIMITED POWERLINE CARRIER DEVICES PLUG IN TRANSFORMER e g ADEMCO 1332 CANADA USE 1332CN a i TAIS EQUIBWIENT SHOULD BE INSTALLED ia ome ante piezo eeu ovac F 70 2ang 11ovac i EARTH INCOMING HANDSET TIN ACCORDANCE WITH THE NATIONAL ane BONE eae LJ ri pave Onto f FIRE PROTECTION ASSOCIATION S STAN H LINE LINE iB DARD 72 CHAPTER 2 NATIONAL FIRE ak teks tego ee NOTE BACKUP BATTERY IS REQUIRED USE PROTECTION ASSOC BATTERYMARCH 2k OHMS F WAVESEX SINGLE 9V ALKALINE BATTERY e g DURACELL R eH C1604 PROCELL OR SIX 1 5V ALKALINE AA PARK QUINCY MA 02269 PRINTED EOL i INFORMATION DESCRIBING PROPER BATTERIES e g DURACELL MN1500 i INSTALLATION OPERATION TESTING i MAINTENANCE EVACUATION PLANNING i AND REPAIR SERVICE IS TO BE PROVIDED WEEKLY TESTING IS REQUIRED TO ENSURE REPLACE BATTERY AT LEAST EVERY YEAR i BLACK WITH THIS EQUIPMENT PROPER OPERATION isis OF THIS SYSTEM MELLOW POWERLINE INTERFACE ty FR GEVIGE GOLPLIER WIDMER TRORROD RULER T GREEN THIS DEVICE COMPLIES WITH PART 15 OF FCC RULI FOO ID OF SeDLLVAN 1234 OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVE2. 1 2 3 4 5 6 Separate the front assembly from the back plate and mount the back plate DO NOT disconnect the ribbon cable from the terminal strip board Disconnect the cable only from the front assembly board Make wiring connections as follows Connect the incoming phone line to either the 8 position jack or terminals 2 TIP and 3 RING Connect the handset phone lines to either the RJ11 jack or terminals 4 TIP and 5 RING NOTE For full line seize operation see the installation instructions If used connect a piezo sounder to terminals 10 and 11 If used connect a bell to terminals 11 and 12 If using Powerline Carrier Devices connect com data sync lines from the PL513 Powerline Interface Module to terminals 9 13 and 14 respectively Install Powerline Carrier Devices according to their instructions Connect wires from the 1332 1332CN AC Transformer to terminals 15 and 16 After all wiring connections are made carefully reconnect the ribbon cable to the front assembly PC board connector properly aligning the red wire then snap the front assembly to the back plate so it is held by the locking tabs Plug the transformer into a 24 hour 110VAC unswitched outlet Slide out the battery drawer and install either a single 9V alkaline battery or six 1 5V AA alkaline batteries Use only nonrechargeable alkaline batteries After installing the battery ies slide the battery drawer i
3. 94 Download Phone Number then enter the downloading computer phone number up to 20 digits If fewer than 20 digits are used press to end the field Enroll transmitter serial numbers by pressing 83 while in Programming mode then follow the prompts Enter the 2 digit zone number of the first transmitter whose serial number you are entering then press The system displays the C prompt Enter the 7 digit serial number printed on the transmitter If you enter an incorrect digit press the key to back up to that digit and reenter the correct digit When all 7 digits are entered press the key Review the displayed serial number If correct press again to save it The next zone number to be enrolled will display at the C prompt for 30 seconds If this is the desired zone number enter its serial number as described above If not either wait 30 seconds or press the key to display the b prompt The system automatically displays the next zone number for which a serial number may be enrolled Press 1 to return to the C prompt described above to enroll this zone If the zone number displayed is not desired press 0 to return to the A prompt where you can then enter a different zone number After all serial numbers have been enrolled return to the A prompt then enter 00 to exit enrollment mode blinking 83 Press 99 to exit Program mode Page 2 Set RF House
4. function refer to the procedure in the Aux Function section of the User Manual Note The 1 button paging feature field 87 is not enabled with the default programming NOTE The Babysitter Code and Installer Code cannot disarm the system unless it was the code used to arm the system In addition if the system is armed by pressing and holding the Quick Arm buttons neither the Babysitter Code nor the Installer Code can disarm the system REFER TO THE INSTALLATION INSTRUCTIONS FOR THE LIMITATIONS OF THIS SYSTEM AND WARRANTY INFORMATION ADEMCO GROUP 165 Eileen Way Syosset New York 11791 Copyright 1998 N8889QS 10 98
5. 90 ENROLL AS RF ENROLL AS RF Page 3 Keypad Functions when default programming is used Security Functions Checking system status high level messages press again for secondary messages To arm in STAY mode Press and hold down or enter your code See note below To restart exit delay applies only if system is armed in Stay mode To arm in AWAY mode Press and hold down or enter your code See note below To arm with NO DELAY Press and hold down or To disarm the system and silence alarms User Code See note below To bypass a zone s User Code 2 digit zone number s To turn Chime mode on or off Message Center To record a message To stop recording before end of 20 seconds To play back a message Volume Control To adjust message playback system announcement volume 3 Up or 6 Down To mute system announcements To restore announcement sounding 3 or 6 Other Functions To set the time and date User Code 63 To activate or deactivate devices 1 6 or device number To activate or deactivate devices 7 amp 8 User Code or dev no To add a User Code Master Code usernumber User s Code see note below To delete a User Code except Master Code Master Code user number To turn Test mode on User Code To turn Test mode off User Code To use the defined AUX function Press and hold key 2 secs 4 beeps User Code To define the AUX
6. ADEMCO Introduction Quick Start Guide Previous menu N8889QS 10 98 LYNX This Quick Start Guide can help you install the LYNX quickly and easily by providing the basic steps for installation using the built in defaults For more detailed information and important notes refer to the LYNX Installation Instructions The following steps assume that one of the system s default tables will be used For programming data values and Powerline Carrier Devices other than those listed in the default tables see the Installation Instructions Default Table Summary Zone Table 1 Table 2 Table 3 Table 4 Table 5 qo eee ee ee te 2 front door front door front door front door front door 3 back door back door back door back door back door 4 window window window window window 5 motion detector motion detector window window motion detector 6 smoke detector window window 2s 7o eee window window Sc _e motion detector motion detector e a a a smoke detector smoke detector 26 loop 3 arm away t t t 27 loop 2 disarm t En t 28 loop 4 close device 1 t t t 29 loop 1 restore device 1 t t 30 loop 3 arm away t t t 31 loop 2 disarm t t t 32 loop 4 close device 1 t t t 33 loop 1 restore device 1 t 92 duress duress duress duress duress 99 silent alarm silent alarm silent alarm silent alar
7. D INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION LYNX WIRING CONNECTIONS 5800 Series Transmitter Loop Numbers The following illustration shows the compatible transmitters and their associated input types and loop designations CANADA 174810211654 COMPLIES WITH FCC RULES PART 68 FCC REGISTRATION No 5GBUSA 25623 Al RINGER EQUIVALENCE 0 6B 4 WIRE MODULAR PHONE CORD WITH FLYING LEADS Il Loop 3 m too LOOP E LOOP 1 lt LOOP 1 E REREN eee FS crerminats m TERMINALS 1 tars ass LOOP 4 TERNATE YOU MUST 5816 Ag 5816MN a LOCKING TABS ENROLL THIS ENROLL AS RF ron oN ENROLL AS RF ee _ 5802 5802CP Wt A ny iiti ENROLL AS BR pF ENROLL AS UR OR RF ae Loop Mus LOOP 3 PRIMARY NOTE ENROLL THIS 4 2 Loop MAKE SURE BATTERY ON Wares AUX CENTER 1 CLIPS ENTER SLOTS LOOP 4 3 WHEN SNAPPING Loop 1 0x RIGHT 5818 FRONT ASSEMBLY ag ENROLL AS RF TOBACKPLATE f 5817 ENROLL AS RF Loop 2 REED LOOP 1 TERMINALS 5819 LO P3 ENROLL AS RF TERMINALS 5802MN ENROLL AS UR OR RF 5827 SET HOUSE CODE 5804 ENROLL AS BR 5827BD SET HOUSE CODE DISCONNECT THIS END ONLY 5806 5807 5808 5806 SHOWN ENROLL AS RF LOOP Loop 1 MOTION MOTION 5804BD ENROLL AS BR 5849 58
8. ID in the wireless keypads as follows If using a 5827 wireless keypad set the keypad s DIP switches to the RF House ID programmed in field 24 If using a 5804BD button key or 5827BD keypad set the RF House ID per its instructions If using Powerline Carrier Devices set their House ID to A programmed as O or use field 25 to change the ID to avoid conflicts with existing installations Set the Real Time Clock as follows Enter time date setting mode by entering the Installer Code 63 The hour prompt is displayed Enter the correct hour then press to accept and advance For each subsequent prompt enter the correct value then press You will exit this mode automatically after entering the year or if no keys are pressed for 1 minute 9 Test the system as follows After installation and programming enter Installer Code 5 To exit Test mode enter Installer Code OFF 10 Assign desired User Codes by following the procedures on the next page and in the User Guide Show the user how to perform the various system functions 11 Perform site initiated downloader session to load central station ID by Installer Code 1 WARNING HONE TO PREVENT RISK OF SHOCK DISCONNECT TELEPHONE LINE AT TELCO JACK BEFORE SERVICING THIS UNIT EARTH FRONS RJ11 TO HANDSET PHONE ZONE N U SOUNDERS PLCD AC DA C O a S 1 IP RI Sa INCOMING PHONE LINE
9. m silent alarm User 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 Code Install 4 1 1 2 4 1 1 2 4 1 1 2 4 1 1 2 4 1 1 2 Code zones 26 33 are RF button zones and programmed the same as in Table 1 Entering Program Mode installer code 8 0 0 Interactive Mode Used to Program 56 Zone Programming Zone characteristics report codes and serial numbers 83 Sequential Mode 5800 Series transmitter serial numbers 84 Assign Zone Voice Descriptors Voice descriptors for each zone Exiting Program Mode 99 allows re entry into the Program mode using Installer Code 8 0 0 98 inhibits re entry into the Programming mode using the Installer Code NOTES e Tables 2 and 4 support the automatic paging feature open close events reported to pager phone number and a Powerline Carrier Device programmed as device 8 which closes and stays closed upon burglary alarms and restores after bell timeout For other applications or actions e g using a pulsing siren see the 80 Powerline Carrier Device Programming section of the Installation Instructions e Primary report format for all tables is Ademco s Contact ID reporting Tables 2 and 4 also use Contact ID for secondary reporting Tables 1 3 and 5 use 4 1 format for secondary reporting e Tables 1 and 5 record all events in the event log Tables 2 3 and 4 record only alarms alarm restores troubles and trouble restores in their event logs Steps to Installing LYNX
10. nto the back plate only after AC power has been applied Set a programming default Enter Programming mode Installer Code 8 0 0 Press 97 then press a number 1 5 to select a default table from the tables listed on page 1 Program the variable data fields Press 24 RF House ID then enter the desired 2 digit RF House ID for wireless keypads Press 40 PABX Code if used then enter up to 6 digits If fewer than 6 digits are used press to end the field and advance to the next field Press 41 Primary Phone Number then enter the primary phone number up to 20 digits If fewer than 20 digits are used press to end the field and advance to the next field Press 42 Secondary Phone Number if used then enter the secondary phone number up to 24 digits If fewer than 24 digits are used press to end the field and advance to the next field Press 43 Primary Account Number then enter the primary account number If only 3 digits are used press to end the field and advance to the next field Press 44 Secondary Account Number if used then enter the secondary account number If only 3 digits are used press to end the field and advance to the next field Press 88 Pager Characters if using Default Table 2 or 4 then enter up to 16 digits which may be required by your pager service e g account number PIN etc If fewer than 16 digits are used press to end the field and advance to the next field Press
Download Pdf Manuals
Related Search