Operating Manual
Contents
1. Coin Counter Instruction Manual Model Modele Modell Modello Modelo Malli GH476 UK Safety Tips e Position on a flat stable surface e A service agent qualified technician should carry out installation and any repairs if required Do not remove any components on this product e Consult Local and National Standards to comply with the following o Health and Safety at Work Legislation o BS EN Codes of Practice o Fire Precautions o IEE Wiring Regulations o Building Regulations e DO NOT immerse the appliance in water or use jet pressure washers to clean the appliance e Do not use the appliance for anything other than its intended use e Always switch off and disconnect the power supply to the appliance when not in use e Not suitable for outdoor use e Keep all packaging away from children Dispose of the packaging in accordance to the regulations of local authorities e lf the power cord is damaged it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety Introduction Please take a few moments to carefully read through this manual Correct maintenance and operation of this machine2. to remove the coins for bagging etc Press the BATCH key Previously set batch quantities for each slot will be displayed Press BATCH key to select desired slot number Use and to increase decrease batch quantity Press RESTART key to begin counting When each slot reached desired batch quantity unit will stop To continue counting press RESTART key RS NA Cleaning Care amp Maintenance e Disconnect from power by removing the plug Wipe surfaces with a clean dry cloth e Do not use corrosive cleaning agents as this may damage the unit UK Trouble Shooting Fault Probable Cause LCD display not working No power Aste e sure the machine is plugged in correctly On Off switch in Off position Switch On Off switch to ON position Error message OPEN is Hopper is open Close the A displayed Error message E02 is displayed Counting Wheel sensor error Jia your Buffalo Dealer Error message CSE is displayed Relevant Coin Slot is full Remove coins from SLOT and with flashing Slot Number press RESTART to clear and restart the machine Error message CS01 08 is Counting Sensor Error Contact your Buffalo Dealer displayed Technical Specification Dimensions Weight Voltage hxwx MET mm EA GHa76 24v 24vDC 270x373x382 0 x 373 x 382 Electrical Wiring This appliance is supplied with a 24v AC DC adaptor This is non serviceable and should be replaced if faulty If in doubt consult a qualified electrician E
3. will provide the best possible performance from your BUFFALO product Pack Contents The following is included e BUFFALO Coin Counter e Instruction Manual BUFFALO prides itself on quality and service ensuring that at the time of packaging the contents are supplied fully functional and free of damage Should you find any damage as a result of transit please contact your BUFFALO dealer immediately UK Keyboard and LCD Display A Slot Number B Number of Coins in Slot C Value of all Coins counted D Plus E Minus F Batch Function G Cancel H Stop Restart Operation 1 Connect unit to the power supply and switch on power switch located at the rear of the unit 2 Pour coins to be counted into the hopper 3 Press the RESTART button to commence counting 4 Use hands combined with the feeding guide to feed coins onto the rotating turntable 5 The machine will sort and count the coins Coins will be deposited into the individual hopper trays 6 The LCD display will show how many coins are in each numbered slot 1 8 and the total value of all the sorted coins 7 Press STOP at any time to STOP machine Sorting 8 Press C to reset Counter to 0 UK Value of Slots eo e002 i 8 2 00 Batch Function The BATCH function allows you to count a specific number of coins per slot When the number of coins reaches the desired batch quantity the unit will stop allowing the operator the opportunity
4. e 2004 108 EC ROHS Directive 2002 95 EC EN 60950 1 2006 A12 2011 EN 55022 2010 EN 61000 3 2 2006 EN 61000 3 3 2008 EN 55024 2010 IEC 62321 Buffalo Fourth Way Avonmouth Bristol BS11 STB United Kingdom I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s Date Signature Full Name Position 07 10 13 lm Richard Cromwell Commercial Director GH476_UK_V1
5. lectrical isolation points must be kept clear of any obstructions In the event of any emergency disconnection being required they must be readily accessible UK Compliance The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste To help prevent possible harm to human health and or the environment the product must be disposed of in an approved and environmentally safe recycling process For further information on how to dispose of this product correctly contact the product supplier or the local authority responsible for waste disposal in your area BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international independent and federal authorities BUFFALO products have been approved to carry the following symbol All rights reserved No part of these instructions may be produced or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of BUFFALO Every effort is made to ensure all details are correct at the time of going to press however BUFFALO reserve the right to change specifications without notice DECLARATION OF CONFORMITY Equipment Type Model e Application of Council Directives s Standards Producer Name Producer Address Coin Counter GH476 LVD Directive 2006 95 EC EMC Directiv
Download Pdf Manuals
Related Search