utility sink with extendable faucet and storage cabinet
Contents
1. 2 Use this unit only the manner intended by the manufacturer If you have any questions contact the manufacturer 3 Installation work and plumbing must be done by qualified person s in accordance with all applicable codes and standards Protect the entire surface during installation AII holes drilled into the unit must be done from the finished surface side with extreme care and caulked very carefully to form a watertight barrier Warranty ONE YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation Conglom Kitchen amp Bath warrants this product to be free from defects in materials or workmanship for one 1 year from the date of purchase Proof of purchase original sales receipt from the original consumer purchaser must be made available to Conglom Kitchen amp Bath for all warranty claims This warranty is non transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer s instructions It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen amp Bath replacement parts Replacement parts may be obtained by e mail at customer service conglomkb com or by calling 1 877 333 0098 between 8 30 am 52. or 1 877 333 0098 Service available in English and French Monday Friday from 8 30am 5pm EST Identify the required part s and have the part number s ready Part Description Code Quantity A Sprayer head QHL115 1 B Ceramic cartridge 0 5121 1 Faucet lever QHL116 1 D Strainer assembly QHS103 1 E Strainer basket QHL118 1 F Handles QHL119 2 G Leveling legs QHL121 4 AA Handle screws QHL120 4 Imported by Conglom KITCHEN amp BATH St Laurent Qu bec H4S 2C3 1 877 333 0098 customer service conglomkb com Service available in English and French Monday Friday from 8 30am 5pm EST www conglomkb com Made in China
3. 00 pm EST installation error abuse misuse or improper care and maintenance whether performed by a plumber contractor service provider or member of the purchaser s household The warranty excludes damage due to aggressive air or water conditions harsh or abrasive cleaners and or materials Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this product We will not be held liable for inconvenience caused by loss of use of this product costs incurred for labour or materials removal and installation of replacement units or any other incidental or consequential damages Costs relating to obtaining access for repair or replacement are the responsibility of the user Our obligation shall be limited to the repair or replacement of a unit at our discretion that may prove by our sole examination to be defective under normal use and service during the warranty period Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty These non warrantable items include but are not limited to Improper installation not in accordance with manufacturer s instructions Dents and or scratches incurred during shipping handling or installation Change in colour or finish due to chemical usage Damage caused by failure to follow care and cleaning guidelines including damage caused by the use of abrasive clean
4. 98 for further assistance Installation continued INSTALLING THE STRAINER 1 Apply a ring of plumber s putty to the underside of the strainer flange 2 Insert the strainer body into the sink 3 Assemble the rubber gasket friction washer and locknut onto the strainer body from under the sink 4 Hand tighten the locknut Do not over tighten the locknut as it may split or deform the strainer body 5 The strainer basket can be placed in the strainer body once the utility sink is installed CA O Jj Sealant Basket Strainer body Rubber gasket Friction washer Locknut Installation continued MOUNTING THE UTILITY SINK 1 Carefully place a bead of sealant all around the top of the cabinet A 2 Easethe utility sink D into the cabinet A Ensure that it is placed evenly and is centered on the cabinet Wipe off any excess sealant Use masking tape to hold the basin in place until the sealant dries 9 CONGLOMKB COM Please contact 1 877 333 0098 for further assistance Installation continued PLACEMENT Move the assembled unit to its final location If required level the unit by adjusting the four leveling legs Ensure that no rocking is exhibited SUPPLY LINE The supply lines which connect the faucet to the household water system are not supplied with this unit Tney need to be purchased separately Follow the supply line manufactur
5. UTILITY SINK WITH PRESENZA EXTENDABLE FAUCET AND STORAGE CABINET INSTALLATION GUIDE AND USER MANUAL ITM ART 485028 Model No QL0282 Table of Contents Table of Contents 2 Installing the Faucet 7 Safety 2 Installing the Strainer 8 Warranty Mounting the Utility 5 9 One Year Limited 3 Placement 10 Warranty Claim 3 SUPPIV LINO s at ea 10 Pre Installation Maintenance Tools Materials 4 Cartridge Replacement 10 Parts Required 0 ccc cece eee eee eens 4 Drawer Removal 11 Package Contents 5 Care and Cleaning Installation Utility Sink iii 11 Installing the Leveling 6 A A 11 Installing the Handles 7 Service Parts 12 Safety Information READ AND SAVE THESE INSTRUCTIONS DANGER Always wear safety goggles and gloves in order to avoid personal injury 1 Inspectyour unit before proceeding Once you unpack your unit check for chips scratches cracks dents or scuff marks If any damage is noticed do not install
6. assembly 1 F Strainer basket 1 G Leveling legs 4 H Caster pre installed on cabinet 1 AA Handle screws 4 CONGLOMKB COM Please contact 1 877 333 0098 for further assistance Installation INSTALLING THE LEVELING LEGS Carefully check the utility sink for damage and or missing parts prior to installation If there is any damage or if you are missing parts WARNING Always wear safety goggles and gloves during do not proceed with the installation Report damage and or missing installation parts immediately to the manufacturer Do not dispose of packaging before you are satisfied with your new utility sink l CAUTION Do not place side load on the leveling legs when righting the cabinet as they may break Remove the utility sink D and place it on a soft protective surface Fig 1 Gently place the cabinet A onto its back on a soft protective surface D I i Fig 1 Screw the four leveling legs G into the pre installed nuts on the bottom of the cabinet Fig 2 y a Gently right the cabinet H Using a carpenter s level turn the base of each leg until the cabinet is level G e NOTE Y The caster H is pre installed Fig 2 Installation continued INSTALLING THE HANDLES Insert two handle screws AA into the pre drilled holes on top panel A
7. er s instructions for proper installation Maintenance CARTRIDGE REPLACEMENT If in the future the ceramic cartridge needs to be replaced 1 2 Turn off the water supply to the faucet Remove the faucet lever by hand Loosen the screw with the Allen wrench provided and pull the handle body out The top lever of the cartridge will be exposed Unscrew the cap and rings making sure not to damage the threads Pull the cartridge out of the faucet body and replace it with a new 35 mm ceramic cartridge Replace the rings then the cap Then place the handle body on the cartridge Hand tighten the screw back into the handle body then tighten it with the Allen wrench Do not over tighten Tighten the faucet lever back on Slowly open the water feed to the faucet to test Cartridge e OW Faucet body Handle Rings gt Screw Handle body Maintenance continued DRAWER REMOVAL AND REPLACEMENT To remove the drawer pull it out to its fullest extension On each of the drawer slides there is a black lever Push the lever on the left slide up and the lever on the right slide down The drawer should now slide away from the cabinet Reverse this procedure to replace the drawer Right drawer slide Black lever jo gt Left drawer slide td Black lever Care and Cleaning UTILITY SINK This utili
8. ers Alterations made to the unit by the purchaser or installer Damage caused by accidental impact fire flood freezing and normal wear Bends and warping caused by forced connections over tightened fittings and inadequate support during installation This warranty does not extend to commercial and institutional installation or use WARRANTY CLAIM PROCEDURE If a claimable defect occurs or replacement parts are needed please contact our customer service team at customer service conglomkb com or 1 877 333 0098 Service available in English and French Monday Friday from 8 30am 5pm EST Before you make your call please ensure that you have Model number or description Proof of sale Details regarding the defect and or part number Name s and address es of the owner and or installer 3 CONGLOMKB COM Please contact 1 877 333 0098 for further assistance Pre Installation TOOLS MATERIALS REQUIRED NOT SUPPLIED Adjustable Needle nose Phillips wrench pliers screwdriver Utility knife Pipe wrench a Sealant Hacksaw Carpenter s level U Allen wrench Safety gloves CAO Safety goggles PARTS REQUIRED NOT SUPPLIED Tail Pipe P Trap Supply line Pre Installation continued PACKAGE CONTENTS pl pene Ga HS Part Description Quantity A Cabinet 1 B Faucet 1 C Drawer handles 2 D Utility sink 1 E Strainer
9. ttach a handle C and tighten the handle screws AA Repeat on bottom drawer INSTALLING THE FAUCET Unscrew the retaining ring 16 from the bottom of the body base 11 ensuring that the gasket 14 and washer 15 are removed with the retaining ring Place the lower part of the body base 11 through the hole in the sink From underneath slide the gasket 14 washer 15 and the retaining ring 16 until in correct position Tighten the retaining ring 16 by hand until it is snug Using a wrench or pliers tighten the entire assembly Gently tighten the two screws 17 on the retaining ring DO NOT OVER TIGHTEN Attach the end of the hose with the small fitting 18 onto the faucet outlet 20 and hand tighten Then using one wrench on the hexagonal nut of the faucet outlet and another on the hose nut tighten the two ends together Tightening with just a single wrench may deform the nut on the hose Install the counterweight 19 on the hose about 432 mm 17 in from the underside of the faucet This can be adjusted based on your own requirements Screw the sprayer head 1 onto the end of the hose 4 Attach the lever 13 to the handle base 12 NOTE Please ensure that the flexible risers included in the faucet are not kinked or forced during installation 14 15 432mm 16 17 in 17 CONGLOMKB COM Please contact 1 877 333 00
10. ty sink is manufactured with premium acrylic With the proper care and enjoyment Use common household cleaners non abrasive or a mild liquid dish washing detergent Rinse well and dry with a clean cloth Remove dust and dry dirt with a soft damp cloth Clean grease oil paint and ink stains with isopropyl rubbing alcohol Immediately rinse with water after removal of stain maintenance it will provide you with many years of Do not allow your acrylic surface to come into contact with products such as acetone nail polish remover nail polish dry cleaning solution lacquer thinners gasoline pine oil etc Use caution when using sharp instruments that may fall and scratch the surface CABINET To maintain the surface of your cabinet follow these tips Remove dust and dry dirt with a soft damp cloth Clean grease oil paint and ink stains with isopropyl rubbing alcohol Immediately rinse with water after stain removal Do not allow your cabinet surface to come into contact with products such as acetone nail polish remover nail polish dry cleaning solution lacquer thinners gasoline pine oil etc Use caution when using sharp instruments that may fall and scratch the surface CONGLOMKB COM Please contact 1 877 333 0098 for further assistance Service Parts If you are missing parts or if you require replacement parts please contact our customer service team at customer service conglomkb com
Download Pdf Manuals
Related Search