Camco CAI CP-IP Remote Control Manual
Contents
1. Scan Devices Button to open the Scan Devices Window 3 Press the Scan Button to search available Devices connected to your EtherCai Node 4 Press the Save Button to save the result 5 4 Manual Setup of CAI equipped Devices 5 4 1 Adding a Device Open the Device Setup Window Setup Devices Select a Type of Device and press the ADD Device Button Select the new Device and press the Edit Button You must now enter the correct CAl Address assign it to the correct EtherCAI Node and switch it On You can change the Name of the device the Type of Device and the Visualisation 6 Please press the Save Button RON o 5 4 2 Removing a Device 1 Open the Device Setup Window Setup Devices 2 Select the Device you want to remove and press the Remove Device Button 5 4 3 Edit a Device 1 Open the Device Setup Window Setup Devices 2 Select an Available Device and press the Edit Button 3 You must now enter the correct CAl Address assign it to the correct EtherCAI Node and switch it On 4 You can change the Name of the device the Type of Device and the Visualisation 5 Please press the Save Button Your Setup is now finished2. CAMCO CAI TCP IP Remote Control This file contains install and setup instructions for the CAMCO WinCAI2004 Software and the EtherCAI Nodes to run the CAMCO CAI TCP IP Remote Control System Copyright c 2004 by CAMCO GmbH All rights reserved Content 1 System Definitions 1 1 CAI Overview 1 2 EtherCAl Nodes 1 3 CAI equipped devices CED 1 4 Connectivity 2 System Requirements 3 Hardware Configuration 4 Software Installation 5 Starting WinCAI 2004 5 1 Automatic Setup of EtherCAl Nodes 5 2 Manual Setup of EtherCAl Nodes 5 3 Automatic Setup of CAI equipped Devices 5 4 Manual Setup of CAI equipped Devices 1 System Definitions 1 1 CAI Overview CAI TCP IP remote control www camcosudio com WinCAl 2004 32 Bit Remote Control Software featuring Multithreading communication Full integration of CAMCO Vortex Series amplifiers amp NEXO NX241 controllers Access to any parameters including protection Monitoring of the NX241 and Load Monitoring of the Vortex amplifiers Zoning and controlling multiple NX241 input amp Output meters and all NX241 parameters displayed on a single page EtherCai and NX CAI NetworkCards 100 Ethernet and TCPAP compatible Remote Control potentials via WLAN and Internet Network bridge between IP Network and CAI Network Interface EtherCAl Connect to a Labtop or switcher RJ45 Connector Interface CAI RS485 connection with other CAI equipment RJ11 Connector 32 Un
3. its NX241 amp Vortex Amplifiers per Ethernet Node Unlimited numbers of NX241 and Vortex Amplifiers controlled on the EtherCAI Network 1 2 EtherCAl Nodes Two Types of EtherCAI Nodes are currently available 1 EtherCAI Interface Box 2 NX CAI Network Card plug in module for the Nexo NX241 2 Digital Controller Note Every EtherCAI Node is able to control up to 32 devices 1 3 CAI equipped devices CED 1 CAMCO VORTEX Amplifiers with a full integrated CAI Interface 2 CAMCO DX DL Amplifiers with optinal Modules 3 NEXO NX241 2 Digital Controller with an optional Modul Note Modules for the CAMCO TECTON Series Amplifiers are currently under development 1 4 Connectivity There are two different types of Network Connections used in the System requiring different cables and connectors 1 RS485 cable using RJ11 connectors on the CAI Bus EtherCAI Node to CAI equipped devices CEDs CED to CED 2 CAT5 cable using RJ45 connectors on the Ethernet PC Notebook to Router Router to EtherCAI Node Note RJ stands for Registered Jack RJ XX is a general term for electrical connector designs registered with the US Federal Communications Commission FCC 2 System Requirements 1 IBM compatible PC Notebook running WindowsNT 2000 XP OS equipped with a Network Interface TCP IP protocol installed DHCP Client activated 2 Router or Switch running a DHCP Server 3 One or more EtherCAI Nodes 4 One or more CAI e
4. quipped devices 3 Hardware Configuration Establish a Network connection between your PC Notebook and the Router please refer to section 1 1 CAI Overview of this document 1 Connect the EtherCAI Node to the Router 2 Connect the CAI equipped devices to the EtherCAI Node 3 Switch on all units in the following order Router Computer EtherCAl Nodes CAI equipped devices 4 Program a unique per EtherCAI Node Address into the CAI equipped devices Please refer to the User Manual for the devices how to program the Address 4 Software Installation Please start WCSetup exe and follow the instructions for the Installation 5 Starting WinCAI 2004 Please start WinCAI2004 The Main and the Preset Window will now open Please close the Preset Window and go to step 5 1 5 1 Automatic Setup of EtherCAl Nodes Attention Administrator Privileges are required for Scan Operations 1 Open the EtherCAI Nodes Setup Window Setup EtherCAl 2 Click on the Scan Devices Button to open the Scan Ethernet for EtherCAlI Nodes Window WinCAI2004 checks the TCP IP settings of your computer and automatically provides the settings into the Address Range Fields e g 192 168 10 1 192 168 10 245 and the destination Port Number of your EtherCAI Node 9000 by default Attention Never enter different values unless you are aware of the effect If you are unsure please refer to your System administrator 3 Press the Scan But
5. ton to search available EtherCai Nodes on your network 4 Press the Save Button to save the result 5 Finally restart WinCAI2004 to open the EtherCAl connections Note Any change of EtherCAlI settings require a restart of WinCAI2004 5 2 Manual Setup of EtherCAl Nodes 5 2 1 Adding an EtherCAI Node Open the EtherCAI Nodes Setup Window Setup EtherCAl Select a Type of EtherCAl Node and press the ADD EtherCAI Node Button Select the new Device and press the Edit Button You must now enter the correct IP and Port Number 9000 by default of the device and switch it On You can change the Name of the device and the Type of EtherCAI Node Please press the Save Button RON oo 5 2 2 Removing an EtherCAI Node 1 Open the EtherCAI Nodes Setup Window Setup EtherCAl 2 Select the Device you want to remove and press the Remove an EtherCAI Node Button 5 2 3 Edit an EtherCAl Node 1 Open the EtherCAI Nodes Setup Window Setup EtherCAl 2 Select an Available Device and press the Edit Button 3 You must now enter the correct IP and Port Number 9000 by default of the device and switch it On You can change the Name of the device and the Type of EtherCAI Node Please press the Save Button ak Note Any change of EtherCAI settings require a restart of WinCAI2004 5 3 Automatic Setup of CAI equipped Devices 1 Open the Device Setup Window Setup Devices 2 Click on the
Download Pdf Manuals
Related Search