User Manual - Fingerprint Time Attendance
Contents
1. 6senconds Fingerprint identify x 1 to register the master fingerprint Three master fingerprints should be registered after finishing the master code setting to be assured the safety of the lock usage and management Step I Press button then two short Beep sound place master fingerprint to the sensor window for capture the fingerprints move the fingerprints until the light is off And do twice so with the same fingerprints again Step II the system will automatically judge the previous operation is success or fail If one long Beep sound the master fingerprint register completely if three short Beep it means operation is failure The failure reason may befollowings 1 the feature of the fingerprints is few 2 the fingerprint places the incorrect position 3 the fingerprint places too light Step III repeat step LII until no response to press button it means three master fingerprints are enrolled completely Notice If the master fingerprints are less then 3pcs we should register the new one till the master fingerprints in the lock is not less than 3 pcs or it will be not safe x2 to register the user fingerprints The user fingerprints are enrolled after 3pcs master fingerprints were registered completely Step I Press door handle till the red light of the sensor window is on put the master fingerprint on the sensor till the red light is off If long beep sound it means successful if no response it m2. II the system will delete all fingerprints without the serial No x Appendix 1 Correct pose to place finger Face Side O All rights reserved E Focus Industrial Co Ltd info securiticn com 8 E Focus Industrial www vsstr com www securiticn com 1 Fingerprint Collector 2 Finger is touching the face of collector quartz glass 2 Incorrect pose All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com Precaution Before Use please read user manual before use IEI Fingerprint Door Lock 1 ar The fingerprint collector is quartz glass must be kept clean from the external impact or dirt The fingerprint collector part must be cleaned now and then with a damp cloth to keep the surface clean Mild glass cleaner can be used After placing your finger to unlock the door slide down your fingertip to protect the collector surface from the contamination with dirt It may be difficult to enroll if a finger is very dry Then make the finger moist or little only by rubbing your nose or face or rub in a small amount of hand lotion Batteries selection suggestion high quality Alkali batteries Void to use low quality and large discharge batteries Woman and children s fingerprint is light suggest to enroll fingerprint of middle finger or thumb GALOP All rights reserved E Focus Industrial Co Ltd info securiticn com 10
3. don t press the handle in 6 seconds the system will be closed automatically 36 Unlock Mode Setting The lock can be settled as Unlock Mode when users need the lock to be open continuously StepI Press the lock handle till the red light of the sensor window is on put the Fingerprint on the sensor window till the red light is off if one long beep it means operation is successful if no response it means the operation is failed the system will be off automatically Stepll After the long beep reset Turn out and in the anti lock shaft of the back lock body rapidly The lock will be in the Unlock Mode automatically The lock can be open without any identification StepIII Cancel the Mode repeat StepI the mode cancelled 37 Low battery alert Please change battery if any of the indication appears 1 Press the handle the red light of the front lock lights for 6 seconds 2 After successful identification the red and green light of front lock panel both light for 6 seconds Chapter III Advanced operation instruction In the advanced operation mode the user can set the Number for each Fingerprints For management The number of fingerprints is formed by 3 digits eg 012 123 etc Setting the number when register which is convenient for users to delete the fingerprint with pointed number The same user can use the same number which means one number can be used for several fingerprints of the same user which will be more convenien
4. if three short Beep it means operation is failure The failure reason may be followings 1 the feature of the fingerprints is few 2 the fingerprint places the incorrect position 3 the fingerprint places too light 3 3 to delete the pointed fingerprint Step I to be in the management mode there are two ways 3 press the master code beginning from 0 then one short beep the system go intothe management mode 4 press the handle the red light of the sensor window is on to put the master fingerprint on the sensor window then one long beep sound system goes into the management mode Step II Press 1 or 3 digits numbers beginning from 0 8 Step III Press then two short beep sound repeat the same numbers Step IV Press again then one long beep sound it means the operation is successful if three short beep sound it means failure Notice 1 input number 1 the system will delete all fingerprint No beginning from 1 such as 1xx 2 input number 12 the system will delete all fingerprint No 12x 3 input number 123 the system will delete the fingerprint No 123 only 4 to delete the fingerprint without No When the user registered the fingerprints without No the system will record these fingerprints under number 9 automatically so when deletion them following the steps to delete the fingerprint with pointed No but press the number 9 in Step
5. E Focus Industrial www vsstr com www securiticn com User Manual FL310 Series FL310 Technology Specification Access Fingerprint Password Mechanic Key Fingerprint collector Optical based fingerprint collector Fingerprint collection time lt 0 8s Fingerprint matching lt Is Fingerprint matching type 1 N False acceptance rate FAR lt 0 001 False rejection rate FRR lt 1 Memory capacity 32 users Fingerprint templates Password digits 8 Password capacity 32 users LED low voltage alarm lt 4 2V Operation voltage DC 6V Power 4 x 1 5V AA batteries gt 8000 times authentication Operation Temperature 20C 50C Dimension 355Lx195Wx140D mm Net weight 3 5 kg Chapter I Installation 1 Deadblot box position All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com Y WV SG Ly N SORES SSS SN el All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com 2 Illustration All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com Front lock body 8 Mortise shaft 52 2 Keyhole 9 Fix screws 2 S I Back lok cove
6. eans failed the system will be power off Step II after the master fingerprints identify successfully press immediately then two short Beep put the user fingerprint which you want to register to the sensor window till the red light is off And do twice so with the same fingerprints again if no response it means the identified fingerprint in the step I is not the master fingerprint the system will be off automatically Step III the system will automatically judge the previous operation is success or fail If one long Beep sound the user fingerprint register completely if three short Beep it means operation is failure The failure reason may be followings 1 the feature of the fingerprints is few 2 the fingerprint places the incorrect position 3 the fingerprint places too light Notice if there are three short beep after press button in the step II it means the user fingerprints is enrolled fully x3 to delete the pointed fingerprint Step I Identify the master fingerprint Press door handle till the red light of the sensor window is on put the master fingerprint on the sensor till the red light is off If long beep sound it means successful if no response it means failed the system will be power off automatically Step II after the master fingerprints identify successfully press immediately two short beep put the user fingerprint which will be deleted to the sensor window until the red light of the sensor
7. owings 1 the feature of the fingerprints is few 2 the fingerprint places the incorrect position 3 the fingerprint places too light Step V repeat the operation from step I till there is no response after press master fingerprints are registered full Notice the locks should be keeping three master fingerprints GERI button in the step II it means the 2 2 to register the user fingerprints with No Step I to be in the management mode there are two ways 1 press the master code beginning from 0 then one short beep the system go intothe management mode 2 press the handle the red light of the sensor window is on to put the master fingerprint on the sensor window then one long beep sound system goes into the management mode Step II Press 3 digits numbers beginning from 0 8 eg 012 023 Step III Press then two short beep sound to repeat the same numbers All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com Step IV Press then two short beep sound if the number is wrong it will be alarm with three short beep sound to put the user fingerprint to the sensor window with red light till the red light is off And do twice so with the same fingerprints again Step V the system will automatically judge the previous operation is success or fail If one long Beep sound the user fingerprint register completely
8. r 6 Red LED for low power 13 fBatterybox O Chapter II Fast Operation introduction Password identify xr1 to set master code The master code is initiated by 0 6 8digits length 1 1 to set the first group master code Step I Press 6 8 digits code initiated from 0 Step II Press button then two short beep sound to put the same code to confirm If the code in the second time is different from the first time the system will be three beep sound to alarm Then you should repeat the step I again Step III after put in the correct the code in the second time then press 92 one long beep sound it means operation is successful if three short beep sound it means failed 1 2 to set more than one group master code Put any master code has been set before then one short beep sound it means The system is on the code management mode we can set the new master code as Step LILHI in 1 1 Notice in the mode of code management the system will be off automatically If there is no any further operation in 20 seconds 32 to set user code Having set the master codes you can set the user code which can be 4 8 Digits initiated from 1 9 Step I put any master code having set then one short beep the system is on the mode of code management Step II put the code 4 8digits initiated from 1 9 Step III press button then two short beep sound to put the same code to confirm If the code in second
9. t of management Master fingerprint number should be initiated from 0 eg 088 user fingerprint number should be initiated from egong All rights reserved E Focus Industrial Co Ltd info securiticn com 6 E Focus Industrial www vsstr com www securiticn com 14Control cable 1 Front lock body 15 Initialization touch Figure3 x Ltoinitialize Initialize to unload the lock body there is a small hole on the front lock body the initialized button is in the small hole as such 15 of Figure 3 To press this button with the small screwer then one long beep sound initialized operation is finished the fingerprints and codes in the system are cleared x 2 to register the fingerprints with codes 2 1 after initialization to register first 3 master fingerprints Step I Press 3 digits numbers beginning from 0 eg 012 023 Step II Press button then two short beep sound to repeat the same numbers Step III Press then two short beep sound if the number is wrong it will be alarm with three short beep sound to put the master fingerprint to the sensor window with red light till the red light is off And do twice so with the same fingerprints again Step IV the system will automatically judge the previous operation is success or fail If one long Beep sound the user fingerprint register completely if three short Beep it means operation is failure The failure reason may be foll
10. time is different from the first the system will be three short beep sound the operation is stop Step IV if the code in second time is confirmed then press button it will be one long beep sound it means operation is successful if three short beep sound it means failed 3 to delete the pointed code Step I to put any master code have set then one short beep sound it means The system is on the mode of code management Step II to put the code which need to be deleted Step III press button one long beep sound it means deletion operation Is successful three short beep sound means the code you put is not exist 34 to delete all codes Step I press any master code then one short beep sound it means the system All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com Is on the code management mode Step II press for six times then one long beep sound the deletion operation is successful x5 to open lock by code Press any user code if it is correct it will be one long beep sound the door lock can be open if it is incorrect there is no response please press or 4 or waiting for Ssenconds the system will clear the code you pressed then press the correct ones Notice after press the correct code the lock will be in open status press the handle to open door or the lock will be close if not press the handle in
11. window is power off If no response it means the identified fingerprint in the step I is not the master fingerprint the system will be off automatically Step III If one long Beep sound the user fingerprint register completely if three short Beep it means operation is failure All rights reserved E Focus Industrial Co Ltd info securiticn com 5 E Focus Industrial www vsstr com www securiticn com 4 to delete all fingerprints Step I Identify the master fingerprint Press door handle till the red light of the sensor window is on put the master fingerprint on the sensor till the red light is off If long beep sound it means successful if no response it means failed the system will be power off automatically Step II after the master fingerprints identify successfully press 4 button six times immediately till one long beep it means operation is successful If no response it means the identified fingerprint in the step I is not the master fingerprint the system will be off automatically 365 to open lock by fingerprint Press the lock handle till the red light of the sensor window is on put the Fingerprint on the sensor window till the red light is off if one long beep it means operation is successful if no response it means the operation is failed the system will be off automatically Notice after the fingerprint matching successfully the system is in the open model press the handle to open lock if we
Download Pdf Manuals
Related Search