User manual
Contents
1. regulated Therefore you do not need a big expensive blower that makes a lot of noise and ruins your training A small handblower is enough to inflate even the biggest AirTracks within 4 minutes Also the AirTrack resembles the real gymnastic floor much better because it s flatter page 14 16 Contact Airlrack Factory Should you have any questions or comments regarding this manual please do not hesitate to contact us AirTrack Factory Bijsterhuizen 11 78 6546AS Nijmegen The Netherlands T 31 0 24 8909659 E info airtrackfactory com W www airtrackfactory com page 15 16 AirTrack Factory Bijsterhuizen 11 78 T 31 0 24 8909659 6546AS Nijmegen E info airtrackfactory com The Netherlands W www airtrackfactory com2. Airtrack Factory User manual AIRTRACK Enjoy your User Manual Table of contents Ch Content Page 1 Introduction 5 2 Safety instructions 6 3 Usage instructions 7 4 Set up 8 10 5 Packing 11 6 Problem solving 12 13 7 FAQ 14 8 Contact 15 page 4 16 Airlrack Factory 1 Introduction This manual describes how to use AirTrack Factory s products Please make sure to read through the safety instructions carefully before using your AirProduct Should anything be unclear do not hesitate to Contact us using the information at the bottom of each page We hope you enjoy your new equipment AirTrack Factory page 5 16 User Manual Safety instructions These instructions apply to all inflatable products from AirTrack Factory These products will be referred to as AirProducts or the equipment AirProducts are designed as training equipment for gymnastics cheerleading tumbling school sports showgroups martial arts parkour freerunning and tricking e USE AIRPRODUCTS ONLY FOR THEIR INTENDED PURPOSE e An AirProduct can only be installed by a qualified instructor e Use the equipment only under the supervision of a qualified instructor who is responsible for the proper and safe use of the AirProduct e Do not wear shoes while on an AirProduct for they may damage the surface e Never place an AirProduct near overhead obstructions such as trees or power lines nor place the equipment on a
3. aging an AirProduct by over pressurizing it A No the extreme pressure needed to actually damaging an AirProduct can not be reached with the blowers we supply nor the excersices you would do on it Q 24 Hours after inflation the airtrack is not hard enough anymore do need to repair this A AirTracks are not designed to maintain their pressure overnight Because of differences in temperatures it loses a bit of air and therefore inflating it once per day is not unusual When you have doubts please contact us for a professional opinion Q What is the lifespan or your products A Obviously this will depend on how the products are used and in what frequency A lifespan of more than 7 years is definitely not uncommon Q What guarantees do you give on your products A We give 2 years guarantee on our products Transport costs are not included Please check our terms of delivery for more detailed info Q When our AirProduct is leaking how can you help us A A puncture in the surface or damage to a seam could cause your AirProduct to leak For both options we have a solution that is both simple and cheap You do not have to send the equipment back to us we will send the repair material to you or assist you in purchasing it locally Repairs take no longer than 10 minutes Q What is the difference between these AirTracks and the old Tumble Tracks A The new generation AirTracks from the AirTrack Factory are very airtight and the pressure can be
4. g equipment for gymnastics cheerleading tumbling school sports showgroups martial arts parkour freerunning and tricking Due to their bounciness they are ideal for training skills that require airtime However this bounciness also renders the airproduct unuseful as a landing mat AirProducts are no replacement for landing mats or foam pits Sportsmen of any skill level age weight and size can use the AirProducts Recommended air pressure levels 10 cm 4 inch 70 mbar 100 140 mbar 200 mbar 20 cm 8 inch 40 mbar 70 110 mbar 110 mbar 33 cm 13 inch 30 mbar 50 60 mbar 80 mbar Above pressure levels can be used as a guideline but the optimal pressure level greatly depends on the skill level and weight of the users as well as the type of sports and preferred effect The bounciness of the AirProduct depends on how much pressure you put in it If filled up to the maximum pressure an AirTrack can feel exactly like a dead floor which is useful for competition training Inflating it to a standard level will make it optimal for low to mid level training while inflating it to a minimum level will make it more fun for recreational purposes Note It is impossible to over pressurize an AirProduct with the blowers we supply To prevent damaging the AirProduct never use a blower other than the one supplied with your equipment page 7 16 User Manual Set up Please make sure you have read the safety instructions before proceedi
5. ght It is normal for an AirProduct to lose some pressure over time and you may need to refill them a few times a day 2 Can t fit the AirProduct back in its bag There are a few things you should pay attention to when deflating and rolling up your mat First of all we recommend using the blower to get the last bits of air out of the equipment Connect the blower s adapter to the input side of the blower Hitachi on the side OV10 on the back and deflate until the AirProduct is flat Also be sure to keep the width of the bag in mind when folding up the AirProduct Place the bag at one end of the mat and match the folds to the bag s width to fit it in perfectly page 12 16 Airlrack Factory A black valve seems to be leaking Black valves are equiped with a rubber inlay that prevents air from escaping This ring may sometimes come loose and slightly pop out of the cap Closing the valve in this condition may cause the rubber inlay to take permanent damage Please contact us if you require a rubber ring replacement Before closing the black valves check if the rubber inlay is still in its correct position The pictures below show the rubber inlay in its correct left and incorrect right position CORRECT INCORRECT N page 13 16 User Manual FAQ Q How long does it take to inflate an AirProduct A All AirProduct are inflated within 4 minutes thanks to our high performance blowers Q Is there a chance of dam
6. ng to set up your AirProduct Pick the right location for the AirProduct To prevent damage make sure there is no debris in the area If you re using the AirProduct outside always use a ground cover Move the AirProduct in its transportbag to the desired location Take the AirProduct out of the bag and make sure it s unrolled far enough to reach all the valves Further instructions depend on the kind of valves on the AirProduct AirProducts with black valves AirProducts without black valves Make sure the small grey valves are Make sure the small grey valves are closed pin out and open one of the black closed pin out valves Attach the grey tube to the Hitachi blower Connect the OV10 blower s adapter to the as shown above and insert it into the grey valve by twisting it in black valve Turn on the blower and wait for the AirProduct to reach the desired pressure Turn off and disconnect the blower Using the black valves Be careful not to damage the screw thread by forcing the cap on Block the airflow with your hand before closing the valve Close the valve Use the Hitachi s black adapter or an OV10 blower on the grey valves to fine tune the pressure A manometer helps determine the perfect pressure Enjoy your AirProduct page 8 16 Airlrack Factoru Below Inflating an object without black valves page 9 16 User Manual Below Inflating an object with black valves page 10 16 Airlrack Facto
7. ry 5 Packing 1 Open all valves to start the deflation Start folding or rolling up the AirProduct to speed up the deflation The blower can be used to deflate the object more rapidly Simply attach the blower s tube to the deflation side of the blower see pictures below B 2 When most of the air is out fold the AirProduct so the width matches the transportbag For regular AirTracks this means you should fold the sides towards the middle line and then fold it once more 3 Rull up the AirProduct towards the valves so they remain unblocked for as long as possible The tighter you roll up the object the easier it will be to transport it 4 IMPORTANT After rolling up the AirProduct make sure to close all valves This prevents the caps from damaging the valves screw thread Use the black strap to keep the mat rolled up tight 5 Slide the bag over the roll and flip it or lift the roll into the bag Close the Velcro flaps then the other flaps and close the bag by tightening the straps page 11 16 User Manual Problem solving 1 Does your AirProduct seem to be leaking Make sure that all valves are closed properly The pins inside of the grey valves are often left open pin in when the cap is placed on the valve which means the valve will still be leaking air Always make sure the valve is closed pin out before placing the cap on it Still leaking Please note that our products are not 100 airti
8. slope greater than 5 e Do not bring any sharp items on or close to the AirProduct e Do not jump or land closer than 20 cm to a valve e Assure that the AirProduct has sufficient air pressure to avoid injury Recommended air pressure levels can be found in this user manual e Do not use the AirProduct without using landingmats on both ends For safety reasons also put landing mats on the sides e The area on which the AirProduct is placed must be clean dry flat and free of obstacles e Always set up the AirProduct in the same area where you will be using it When changing the location do not drag the AirProduct over the surface but carry it by the handles e Do not use the AirProduct in humid areas electrocution may occur e Do not use the AirProduct in the rain While inflating the equipment electrocution may occur and also the surface will be slippery which can cause injuries e When setting up the AirProduct outdoor use a groundsheet to avoid damaging the AirProduct e Never pack store or transport the AirProduct when it is wet e The AirProduct is cleaned with water and soft soap Do not use industrial cleaning products e Never use a damaged AirProduct e Never leave an AirProduct outside unattended and keep the air pressure under the maximum values described in this guide e Be aware that AirProducts are not designed as landing mats page 6 16 Airlrack Factory Usage Instructions AirProducts are designed as trainin
Download Pdf Manuals
Related Search