8 ports 10/100Base-TX Module
Contents
1. 2 3 KI ae E eee Half Duplex Half Duplex Half Duplex Half Duplex Full Duplex Full Duplex Full Duplex Full Duplex Table 3 Four ports 100Base FX Fiber Module DIP switch functions 3 3 LED Descriptions There are two LED indicators for each of the Fiber connection ports If there is no connection to a port the corresponding LED indicators are not lit e Link Activity This LED indicator is green when there is a connection secured to a device a link to the corresponding port The LED indicator blinks when there is a transmission of data activity taking place at the corresponding port e Duplex Mode Collision This LED indicator is orange when the corresponding port is operating in Full Duplex mode When the corresponding port is operating in Half Duplex the LED indicator is not lit When collisions are occurring at the corresponding port the LED indicator blinks 4 1000Base SX LX Fiber Module TETA LK ACT aroa aa To A i j KON UY s MIL S6603LX Figure 7 1000Base SX LX Front View When installed into a Switch hub the 1000Base SX LX Module provides 1 Gigabit Ethernet ports which can connect the Switch to a Gigabit Backbone Switch or Server with Gigabit NIC 1000BASE SX In Multimode the fiber optic segment cannot exceed 220m 62 5 125um or 500m 50 125um in length 1000BASE LX e In Multimode the fiber optic segment cannot exceed 550m 62 5 125um or 550m 50 125um in length In single mode the fiber op2. 8 800 packets per second DIP Switch for decision connection mode with other network devices 1 2 DIP Switch with Link Mode The 8 port 10 100Base TX module provides dip switch for 1 to 4 port to adjust link mode with other network devices Another 4 ports use auto negotiation protocol only There are three type of link mode can be chosen Auto negotiation 100Mbps Full duplex and 10Mbps Full duplex adjustable ports DP Sw itchNer i FulDupkx iauto Figure 2 Dip switch location and mode settings If you adjust to auto negotiation then the DIP for 100Mbps and 10Mbps is not effective If you adjust to Full duplex then the DIP for 100Mbps and 10Mbps is effective The following Table 1 lists the ports operating modes based on the DIP switch position PORTA PORT 2 PORT3 PORT4 swt 1 2 3 a ee ae pin N ab Table 1 8 Ports 10 100Base TX Module DIP switch functions 1 3 LED Descriptions There are three LED indicators for each of the RJ 45 LAN connection ports If there is no connection to a port the corresponding LED indicators are not lit e 100Mps This LED indicator is green when the corresponding port is connected to a 100Mbps device This LED indicator is not lit when the corresponding port is connected to a 10Mbps device e Link Activitv This LED indicator is green when there is a connection secured to a device a link to the corresponding port The LED indicator blinks when there is a transmission
3. MiLAN TECHNOLOGY A Division of Digi International User s Manual MIL S2612 2 port 100BASE FX Module ST MIL S2613 2 port 100BASE FX Module SC MIL S2614 2 port 100BASE FX Module MT RJ MIL S2615 2 port 100BASE FX Module VF 45 MIL S2622 4 port 100BASE FX Module ST MIL S2623 4 port 100BASE FX Module SC MIL S2624 4 port 100BASE FX Module MT RJ MIL S2625 4 port 100BASE FX Module VF 45 MIL S3630 8 port 10 100BASE TX Module RJ 45 MIL S6603SX 1 port 1000BASE SX Module SC MIL S6603LX 1 port 1000BASE LX Module SC 1 8 ports 10 100Base TX Module 100 MAX KREERET SRETNE ERE Bree LKACT FDICOL y 4 LOI A yy Qo r 4 LH n ae L 4 mt A 1 2 3 4 5 6 7 8 AN 1 3 WN YS MIL S3630 Figure 1 Front Panel When installed into a Switch hub the 10 100Base TX Module provides 8 10 100Mbps Switch ports which can connect to 10Mbps or 100Mbps hub or end station 1 1 8 Ports 10 100Base Tx Module Features lt gt 4 lt gt 8 10 100Base TX N Way Switch ports Conforms to IEEE 802 3 IEEE 802 3u and IEEE 802 3x standards Store and forward switch architecture for abnormal packet filtering Support for half and full duplex on all ports Backplane up to 2 4Gbps 2M memory Buffer support Automatic address learning with 12K address entry storage Filtering and forwarding rate of 14 880 14
4. e X 1 RX TX 2 RX TX 3 RX TXARX 6 oo ooloo took ee b 2 Figure 5 4 port 100Base TX FX Front View When installed into a Switch hub this Module provides 4 x 100Mbps Fast Ethernet fiber ports which can be used to e Connect the Switch to the backbone of your network that is to a basement switch hub or router Connector the Switch to a 100Mbps server or end station 3 1 Four ports 100Base FX Fiber Module Feature Conforms to IEEE 802 3u Fast Ethernet standard Support SC ST MT RJ VF 45 fiber connector optional Support half and full duplex via DIP switches Store and forward switch architecture for abnormal packets filtering Backplane up to 2 4Gbps Automatic address learning with 12K address entry storage gt gt 4 Filtering and forwarding rate 148 800 packets per second for 100Mbps lt 100Base FX uses 62 5 125 micron multi mode fiber 3 2 DIP Switch with Link Mode An ST SC MT RJ VF 45 connector provides the link to the multi mode fiber cabling or single mode fiber cabling and two LED indicators show the status of the Module at a glance A DIP switch sets the operating mode to half duplex or full duplex default 7 VA aa g n Ia gt l a o MM Ee 1 w SI g z U Ny ke 5 b A X b 7 N Figure 6 Location and setting duplex mode The following Table 3 lists the ports operating modes based on the DIP switch position PORT1 PORT 2 PORT3 PORT4 SW 1
5. nge when the corresponding port is operating in Full Duplex mode When the corresponding port is operating in Half Duplex the LED indicator is not lit e Collision This LED indicators blinks orange when collisions are occurring at the corresponding port
6. of data activity taking place at the corresponding port e Duplex Mode Collision This LED indicator is orange when the corresponding port is operating in Full Duplex mode When the corresponding port is operating in Half Duplex the LED indicator is not lit When collisions are occurring at the corresponding port the LED indicator blinks 2 Two ports 100Base FX Fiber Module e LK ACT FD COL jooljooj MIL S2612 Figure 3 2 port 100Base FX Module Front View When installed into a Switch hub this Module provides a 100Mbps Fast Ethernet fiber port which can be used to Connect the Switch to the backbone of your network that is to a basement switch hub or router Connect the Switch to a 100Mbps server or end station 2 1 Two ports 100Base FX Fiber Module Features Conforms to IEEE 802 3u Fast Ethernet standard lt Support for SC ST MT RJ VF 45 fiber connectors optional lt Supports half and full duplex modes via DIP switches lt Store and forward switch architecture for abnormal packet filtering 2 switching 100Mbps Fiber Ethernet ports Backplane up to 2 4Gbps gt lt Automatic address learning with 12K address entry storage Filtering and forwarding rate of 148 800 packets per second gt 100Base FX uses 62 5 125 micron multi mode fiber 2 2 DIP Switch with Link Mode An ST SC MT RJ VF 45 connector provide
7. s the link to the multi mode fiber cabling or single mode fiber cabling and two LED indicators show the status of the Module at a glance A DIP switch sets the operating mode to half duplex or full duplex default DP Sw itch Location N EERON NO 7 mewt nam N A EE l E 7 N ai amar N Figure 4 Dip switch location and mode settings The following Table 2 lists the ports operating modes based on the DIP switch position Sn PORI PORT 2 Half Duplex Half Duplex Full Duplex Full Duplex Table 2 Two ports 100Base FX Fiber ModuleDIP switch functions 2 3 LED Descriptions There are two LED indicators for each of the Fiber connection ports If there is no connection to a port the corresponding LED indicators are not lit e Link Activitv This LED indicator is green when there is a connection secured to a device a link to the corresponding port The LED indicator blinks when there is a transmission of data activity taking place at the corresponding port e Duplex Mode Collision This LED indicator is orange when the corresponding port is operating in Full Duplex mode When the corresponding port is operating in Half Duplex the LED indicator is not lit When collisions are occurring at the corresponding port the LED indicator blinks 3 Four Ports 100Base FX Fiber Module e LK ACT s FD COL
8. tic segment cannot exceed 10km 9 125um 4 1 1000Base SX LX Fiber Module Features Conforms to IEEE 802 3z draft 4 2 and 802 3x standard lt 1x1000Base SX LX Ethernet Port 3M memory buffer support Standard auto negotiation for speed duplex mode and flow control for MII and GMII PHYs lt Backpressure option and Limit4 option for half duplex lt Automatic address learning with 12K address entry storage 4 2 DIP Switch with Link Mode DP Sw itch Location No 7 N di0 DEEN tT EE ae eae xadna x XN fa La N Figure 8 Location and setting duplex mode If you adjust to Enable N Way then the DIP for Half Duplex and Full Duplex is not effective If you adjust to Disable N Way then the DIP for Half Duplex and Full Duplex is effective The following Table 4 lists the ports operating modes based on the DIP switch position Gigabit Port 1 ia Sa 1 4 2 Table 4 1000Base SX LX Fiber Module DIP switch functions 4 3 LED Descriptions There are four LED indicators for one Gigabit Fiber connection ports If there is no connection to a port the corresponding LED indicators are not lit e Link Activitv This LED indicator is green when there is a connection secured to a device a link to the corresponding port e Activity This LED indicator blinks green when there is a transmission of data activitv taking place at the corresponding port e Duplex Mode This LED indicator is ora
Download Pdf Manuals
Related Search