Home

USB-IF Trademark License Agreement

1. Q Clear Space Avoid visual clutter by maintaining a minimum S amount of clear space around the Logo that is equal to the width of the square of the trident for the size selected Minimum Sizes The minimum size of the largest dimension of the Logo is 5mm 0 2 inches Measurement does not include the Logo Position The Logo can be oriented horizontally with the SS on the left or vertically with the SS at the bottom Licensee is not obligated to use the Circle R and may omit the registered trademark symbol on the SuperSpeed USB Trident Logo for mobile and non mobile Product for which the Licensee is printing engraving on chassis where the reasonable alternatives for the location and size of the Logo do not allow for the symbol to have a maximum dimension of 15mm or more This permission is limited only to these exact situations Where the symbol is so omitted the manufacture Licensees must include the following statement in their user s manual printed materials accompanying the Product The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers Forum Inc and must be accompanied with the image of the mark with the correct rendering of the 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Usage SuperSpeed USB 10 Gbps Trident Logo These requirements apply to the use of the USB IF SuperSpeed USB 10 Gbps T
2. Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 13 10631825 3 EXHIBIT C USB IF ON THE GO Basic Speed USB Logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF ON THE GO Basic Speed UBS Logo COMPANY will receive access to all of the electronic logo art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 14 10631825 3 EXHIBIT D USB IF ON THE GO Hi Speed USB Logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF ON THE GO Hi Speed USB Logo COMPANY will receive access to all of the electronic art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 15 10631825 3 EXHIBIT E USB IF Wireless USB Logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF Wireless USB Logo COMPANY will receive access to all of the electronic art files The logo reproduced above has been protected with a not f
3. Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 24 10631825 3 EXHIBIT N Notification of Passage of USB IF Test Procedure Your Product has passed the USB IF Test Procedure for SuperSpeed USB 10 Gbps SuperSpeed USB Hi Speed USB or Basic Speed USB products or ON THE GO USB IF Test Procedure for Hi Speed USB or Basic Speed USB products or the USB IF Wireless USB Test Procedure for certain Wireless USB products and it has been posted on the USB IF Integrators List As such you are entitled to use the USB IF SuperSpeed USB 10 Gbps SuperSpeed USB Hi Speed USB Basic Speed USB logo or the USB IF ON THE GO Hi Speed USB or Basic Speed USB logo or the USB IF Wireless USB logo or the USB IF Wireless USB GUI logo or the USB Power Delivery or SuperSpeed USB Power Delivery logo or SuperSpeed USB 10 Gbps Power Delivery logo on this Product subject to the terms and conditions of the USB IF Trademark License Agreement and the Exhibits incorporated by reference therein 25 10631825 3 USB Logo Usage Guidelines USB Logo Usage Guidelines N WIRELESS USB am USB UJSB Te SUPERSPEED a SUPERSPEED USB USB 10Gbps 10 a 10 SSS SS e lt gt TM SSS TM USB Logo Usage Guidelines Introduction The Universal Serial Bus USB has gone beyond its original intent to connect peripherals to PCs and is now a dominate standard in t
4. that has been posted on the USB IF Integrators List v the USB IF Wireless USB logo solely in conjunction with product based on the USB IF Wireless USB specification and that use and or interoperate with UWB radios that implement the PHY specification from the WiMedia Alliance that has been submitted to and passed the Wireless USB USB IF Test Procedure and that has been posted on the USB IF Integrators List vi the USB IF Wireless USB GUI logo used on or in connection with a graphical user interface on host hardware implementation products and not on a device that meet all the requirements of Section 1 a v above where use of the USB IF Wireless USB logo set forth in Exhibit E is impracticable provided however that such use is approved in writing by USB IF in advance vii the USB IF SuperSpeed USB logo solely in conjunction with Product that signals at 5 Gbps that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB products and that has been posted on the USB IF Integrators List 10631825 3 viii ix x xi xii xiii xiv xv xvi xvii the USB IF SuperSpeed USB Trident logo solely in conjunction with Product consisting of a cable and connector assembly that signals at 5 Gbps that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB products and that has been posted on the USB IF Integrators List the USB IF SuperSpeed USB T
5. 5 Gbps and that delivers power over USB Vagus and as depicted in the attached Exhibit L and xiii the USB IF SuperSpeed USB 10 Gbps Power Delivery Trident logo for use with product that signals at 10 Gbps and that delivers power over USB Vsus and as depicted in the attached Exhibit M b Product shall mean the specific model or version of COMPANY s product a representative sample of which has been submitted to USB IF has passed the USB IF Test Procedure for Hi Speed USB Basic Speed USB SuperSpeed USB or Wireless USB products and is posted on the USB IF Integrators List c USB IF Test Procedure shall mean the applicable USB IF product testing and compliance requirements as set forth on the USB IF website and as may be amended by USB IF from time to time with reasonable notice d Territory subject to Section 2 e shall mean worldwide e Effective Date shall mean the date of execution of this Agreement by USB IF f Subsidiary ies shall mean a company corporation or other entity in which on a class by class basis more than fifty percent 50 of the stock entitled to vote for the election of directors is owned or controlled directly or indirectly by COMPANY but only so long as 2 10631825 3 such ownership or control exists A Subsidiary is bound by all terms and conditions of this License Agreement to the same extent as COMPANY 2 LICENSE GRANT a Subject to and expressly co
6. a On a dark colored background background of color 2 Color Logo On a dark colored background CERTIRIED PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color Hi Speed USB Versions 3 Color Logo ON THE GO Hi Speed USB Logo USB Red PANTONE 185C CERTIFIED US USB Blue PANTONE 653C ON THE GO Green PANTONE 356C A The 3 color version is the preferred version of the USB IF ON THE GO Hi Speed USB Logo f The 1 color black version of the ON THE GO Hi Speed USB Logo should eae 1 Color Logo be used for single color applications Black CERTIFIED A Choose either the reversed version of the ON THE GO Hi Speed USB Logo or the 3 color version when the ON THE GO Hi Speed USB Logo is used on a dark background A key line has Reverse Logo CERTIFIED been added to the 3 color version to On a dark colored background ensure readability over a background of color 3 Color Logo CERTIFIED USB On a dark colored background a PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All righ
7. passed the USB IF Test Procedure for SuperSpeed USB 10 Gbps products and that has been posted on the USB IF Integrators List or the USB IF SuperSpeed USB 10 Gbps Trident Logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 1 Gen2 specification SuperSpeed USB Trident Logo SuperSpeed USB 10 Gbps Trident Logo 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines The USB IF USB Power Delivery Trident Logo USB Power Delivery may be used solely in conjunction with Product Trident Logo consisting of a cable and connector assembly that signals at 480 Mbps 12 Mbps or 1 5 Mbps and that delivers power over USB VBUS that has been submitted to and passed the USB IF Test Procedure for Basic Speed USB or Hi Speed USB products as applicable and for USB Power Delivery products and that has been posted on the USB IF Integrators List or the USB IF USB Power Delivery Trident Logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 2 0 specification and the USB IF USB Power Delivery specification 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines The USB IF SuperSpeed USB Power Delivery SuperSpeed USB Trident Logo may be used solely in conjunction Power Delivery Logo with Product consisting of
8. radio waves Don t use the wireless Logo without the word WIRELESS eB SUPER Sji i N Don t use the Logo without the word CERTIFIED Don t use the Logo without the word SUPERSPEED Note The Logo don ts guidelines apply to all of the Logo versions 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Don ts Don t use the Logo without the word SUPERSPEED Don t use the Logo without the word 10 Gbps Don t use the Logo without the word CERTIFIED Note The Logo don ts guidelines apply to all of the Logo versions CERTIFIE TZ tesvps SUPERS a CERTIFIE SUPERS AN Ta N 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Don ts TD 200F 2GB Thumbarive Don t use the USB IF SuperSpeed USB Trident Logo or the USB IF SuperSpeed USB 10 Gbps Trident Logo on packaging TD 200F 2GB Thumbdrive Note The Logo don ts guidelines apply to all of the Logo versions 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Incorporating the USB Logo s the USB ON THE GO Logo s the Wireless USB Logo s the SuperSpeed USB Logo s and the SuperSpeed USB 10 Gbps Logo s into your packaging marketing materials advertisements and manuals strengthens
9. utilize the USB IF Marks for wired USB products unless it also passes the Wireless USB Interoperability Test Procedure b The license grant in Section 2 a shall not apply to products functioning as both a wired and a wireless USB Product unless the Product simultaneously passes both the USB IF Wireless and Wired Test Procedures It is not permissible to qualify each functionality independently In the event a Product functioning as both a wired and wireless USB product passes such Test Procedures COMPANY must use the wireless USB Mark in connection with such Product but will have the option of also using the wired USB Mark in connection with such Product c The license grant in Section 2 a shall not apply to Product or product including containing or constituting USB connectors or the designated pins inside the connectors for uses or technology not expressly defined in an applicable USB specification 4 FURTHER CONVEYANCES The license grant in Section 2 a is personal to COMPANY and COMPANY shall not assign transfer or sublicense this License Agreement or any right granted herein in any manner without the prior written consent of USB IF Notwithstanding the foregoing where COMPANY transfers to a third party all or substantially all of the business of COMPANY that is responsible for the manufacture and distribution of Product that party shall be entitled to use the Mark s under the terms of this version of the License Agreement
10. your marketing efforts by informing your consumers of the USB compatibility of your product s The following pages show samples of various marketing materials and examples of the USB Logo placement 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Packaging Packaging is printed in a variety of ways Coarse printing such as flexography on TD 200F corrugate or screen printing on various materials may benefit from using the 1 color or the reverse Logo Product that is printed using finer printing methods such as 4 color process can choose any Logo that best fits their Product box s design The goal is to choose the Logo that will reproduce most attractively onto the material which it is being printed 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Collateral Where you are not restricted by color the full color Logo can be used for your print material In situations where color is restricted use the black or if appropriate 1 color or reverse versions of the Logo p 200F SU PERS PEED Ss USA me ig a I nibh coe AbIscing e oa Ege isq ue tj 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Advertisements For 1 color newspaper advertisements use the black or reverse version of the Logo Full color magazine ads may use the 1 col
11. All rights reserved USB Logo Usage Guidelines Logo Color Basic Speed USB Logo The USB IF Basic Speed USB Logo has been created as a 1 color Logo CERTIFIED PANTONE 653C Other color versions are shown on the following pages It is best to reproduce the Logo using the PANTONE numbers shown at the right When reproducing these colors in 4 color process inks or on screen RGB the screen tints listed here should be used Different color models may reproduce the USB Blue with slight color variations USB Blue e g a Logo printed using USB Blue as a spot color may result in a slightly different hue of blue when compared PORTTA to one printed using 4 color process or Cyan 100 compared to an on screen RGB Logo Mea A Use PANTONE 653C Yellow 0 Black 20 RGB Red 0 PANTONE Colors displayed here may not match PANTONE identified Green 82 standards Consult current PANTONE Color Publications for accurate color Blue 149 PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color Hi Speed USB Logo The USB IF Hi Speed USB Logo has been created as a 2 color Logo Other color versions are shown on the CERTIFIED PANTONE 653C following pages It is best to reproduce PANTONE 185C the Logo using the PANTONE numbers shown at the right When reproducing these colors in 4 color process inks or on
12. COMPANY Address Attention Telephone Fax Email USB IF TRADEMARK LICENSE AGREEMENT This Trademark License Agreement License Agreement is made and entered into as of the Effective Date described below by and between USB Implementers Forum Inc an Oregon USA corporation USB IF and a corporation COMPANY RECITALS WHEREAS USB IF owns good and valuable trademarks and logos WHEREAS USB IF wishes to encourage the distribution of high quality USB products through the maintenance of a USB IF Test Procedure and WHEREAS COMPANY wishes to license use of the Mark s as defined below in accordance with USB IF s terms and conditions described below Now THEREFORE the parties hereby agree as follows 1 DEFINITIONS For purposes of this License Agreement the following terms shall have the following meanings a Mark s shall mean as applicable i the USB IF Basic Speed USB logo for use with product that signals at 12 Mbps or 1 5 Mbps and as depicted in the attached Exhibit A i1 the USB IF Hi Speed USB logo for use with product that signals at 480 Mbps and as depicted in the attached Exhibit B Gii the USB IF ON THE GO Basic Speed USB logo for use with product that signals at 12 Mbps or 1 5 Mbps and as depicted in Exhibit C 10631825 3 iv the USB IF ON THE GO Hi Speed USB logo for use with product that signals at 480 Mbps and as depicted in th
13. Guidelines Logo Usage USB Power Delivery Logos These requirements apply to use of the USB IF USB Power Delivery Trident Logos Licensee in not obligated to use the and may omit the trademark symbol on the USB Power Delivery Trident Logos for mobile and non mobile Product for which the Licensee is printing engraving on chassis where the reasonable alternatives for the location and size of the Logos do not allow for the symbol to have a maximum dimension of 15mm or more This permission is limited only to these exact situations Where the symbol is so omitted the manufacture Licensees must include the following statement in their user s manual printed materials accompanying the Product The USB Power Delivery Trident Logos are trademarks of USB Implementers Forum Inc and must be accompanied with the proper USB Power Delivery Trident image of the mark with the correct rendering of the Clear Space Avoid visual clutter by maintaining a minimum amount of clear space around the Logo that is equal to the width of the battery terminal for the size selected Minimum Size The minimum size of the largest dimension of the Logo is 5mm 0 2 inches Measurement does not include the Logo Position The Logo can be oriented horizontally with the battery terminal to the right or vertically with the battery terminal to the top 2000 2014 USB Implementers Forum Inc USB IF
14. ICT LIABILITY BREACH OF WARRANTIES INFRINGEMENT OF INTELLECTUAL PROPERTY FAILURE OF ESSENTIAL PURPOSE OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT SHALL USB IF BE LIABLE FOR ANY DAMAGES FOR COMPANY S USE OF THE MARK S IN VIOLATION OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT 11 INFRINGEMENT COMPANY shall promptly notify USB IF of any suspected infringement of or challenge to the Mark s or any of its constituent elements 12 TERM OF LICENSE AGREEMENT a The term of this License Agreement shall be for a period of two 2 years from the Effective Date except as to certain Product described in Section 12 b below as to which the term of this License Agreement shall be indefinite provided however that USB IF shall have 8 10631825 3 the right to terminate this License Agreement with cause upon thirty 30 days prior written notice b Upon expiration of this License Agreement the license right set forth herein may be renewed for an additional term by execution of a subsequent version of this License Agreement as amended or not in USB IF s discretion Notwithstanding the foregoing with respect to Product that at the time of the expiration of this License Agreement has passed the USB IF Test Procedure and is posted on the USB IF Integrator s List COMPANY may at its option continue to use the Mark s in conjunction with that Product under the terms of this version of the License A
15. Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Usage SuperSpeed USB Version These requirements apply to use of the USB IF SuperSpeed USB Logo Clear Space Avoid visual clutter by maintaining a minimum amount of clear space around the Logo that is equal to the height of the white space that contains the word certified for the size selected Please note that when the Logo reverses out of a dark background it includes a key line around it The clear space does not include the key line Minimum Size for Print The minimum width of the Logo is 0 75 inch 19 mm and the minimum height for the Logo is 0 38 inch 9 8 mm Minimum Size for On Screen The minimum width of the Logo is 125 pixels The supplied on screen Logos are created with the clear space built into the files The smallest file available 125 pixels is set to the minimum size requirement and should not be scaled down Logo Position To position the Logo correctly use the upper left corner top arrow as the vertical guideline Use the top edge of the word SUPERSPEED as the horizontal guideline _ SUPERSPEED CERTIFIED USB SUPERSPEED Isen CERT aa 3 SUPERSPEED SUPERSPEED arr N USB gt 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Usage SuperSpeed USB 10 Gbps Version These requirements apply to use of
16. PANY may not use or reproduce the Mark s in any manner whatsoever other than as expressly described in Exhibit O g COMPANY agrees and acknowledges that USB IF retains all right title and interest in and to the Mark s Except as expressly granted in this License Agreement COMPANY shall have no rights in the Mark s Under no circumstances will anything in this License Agreement be construed as granting by implication estoppel or otherwise a license to any USB IF technology or proprietary right other than the permitted use of the Mark s pursuant to Section 2 a h COMPANY represents and warrants that it will use the Mark s solely as provided in this License Agreement and will not use the Mark s for promotional goods or products which in USB IF s reasonable judgment will diminish or otherwise damage USB IF s goodwill in the Mark s including but not limited to uses which could be deemed to be obscene pornographic excessively violent or otherwise in poor taste or unlawful or which purpose or objective is to encourage unlawful activities 10631825 3 3 PRODUCTS EXCLUDED FROM LICENSE GRANT a A product utilizing any means of wireless communication operating within the 3 1 to 10 6 GHz spectrum occupying a bandwidth greater than 20 percent of the center frequency or a bandwidth of at least 500 MHz and based on any standard other than the WiMedia PHY and MAC specifications as may be amended from time to time cannot qualify to
17. Please note that the trademark the word certified the plus label and the 10 Gbps label are integral parts of the Logos They are considered part of the Logo art and should not be altered in any way The Logos must be reproduced from the USB IF digital artwork files SuperSpeed USB Version SuperSpeed USB 10 Gbps Version SUPERSPEED SUPERSPEED CERTIFIED USB 10Gbps 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines The USB IF SuperSpeed USB Trident Logo is available with and without the 10 label The SuperSpeed USB Trident Logo is for use with product that signals at 5 Gbps The SuperSpeed USB 10 Gbps Trident Logo is for use with product that signals at 10 Gbps The SuperSpeed USB Trident Logo may be used solely in conjunction with Product consisting of a cable and connector assembly that signals at 5 Gbps that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB products and that has been posted on the USB IF Integrators List or the USB IF SuperSpeed USB Trident Logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 0 and USB 3 1 Gen1 specifications The USB IF SuperSpeed USB 10 Gbps Trident Logo may be used solely in conjunction with Product consisting of a cable and connector assembly that signals at 10 Gbps that has been submitted to and
18. Speed USB Versions To be effective the USB IF Basic Speed USB Logo and the USB IF ON THE GO USB Logo must be treated appropriately and consistently Clear space minimum size and Logo position requirements must be followed These requirements apply to use of both the Basic Speed USB Logo and the USB ON THE GO Logo Logo Usage Clear Space Avoid visual clutter by maintaining a minimum amount of clear space around the Logo that is equal to the height of the blue bar that contains g the word certified for the size selected Please CERTIFIED note that when the Logo reverses out of a dark l background it includes a key line around it The clear space does not include the key line Minimum Size for Print The minimum width of the Logos is 0 5 inch 13 mm and the minimum height for the USB Logo Fz USB i c USB is 0 17 inch 4 3 mm and 0 23 inch 5 85 mm for lt gt the USB ON THE GO Logo Minimum Size for On Screen The minimum width of the Logo is 100 pixels The supplied on screen Logos are created with the clear space built into the files The smallest file available 100 pixels is set to the minimum size requirement and should not be scaled down CERTIFIED Logo Position To position the Logo correctly use the left corner of the Logo as the vertical guideline Use the top edge of the Logo as the horizontal guideline J CERTIFIED 2000 2014 USB Implementers Forum Inc USB IF All ri
19. USB 10 Gbps Logo s the SuperSpeed USB Trident Logo s the SuperSpeed USB 10 Gbps Trident Logo s and the USB Power Delivery Logo s are available in various digital file formats Print Applications Encapsulated Postscript EPS files were created in Adobe Illustrator and can be reproduced at any size without compromising quality Use these versions for printing Each version is a separate file Logos can be printed using either PANTONE colors or the 4 color process mix specified on page 6 Type has been converted to outlines no fonts are required to reproduce the Logos The files have been saved for both Macintosh and PC On Screen Applications These versions are for on screen applications such as the Web or Microsoft PowerPoint presentations They have been created in RGB color mode and should not be used for offset printing These versions were rasterized in Adobe Photoshop from Adobe Illustrator files with the exception of the EPS files Keep in mind that these files look their best when placed at 100 size or smaller PNG and or JPG files are provided for use in on screen applications EPS files were created in Adobe Illustrator and are saved in RGB color format These files are to be used in software applications that utilize vector based artwork e g Adobe Flash Third party names and brands are the property of their respective owners PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Fo
20. a cable and connector assembly that signals at 5 Gbps and that delivers power over USB VBUS that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB products and for USB Power Delivery products and that has been posted on the USB IF Integrators List or the USB IF SuperSpeed USB Power Delivery Trident Logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 0 USB 3 1 Gen1 and the USB IF USB Power Delivery specifications 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines The USB IF SuperSpeed USB 10 Gbps Power SuperSpeed USB 10 Gbps Delivery Trident Logo may be used solely in Power Delivery Logo conjunction with Product consisting of a cable and connector assembly that signals at 10 Gbps and that delivers power over USB VBUS that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB 10 Gbps products and for USB Power Delivery products and that has been posted on the USB IF Integrators List or the USB IF SuperSpeed USB 10 Gbps Power Delivery Trident Logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 1 Gen2 and the USB IF USB Power Delivery specifications TM 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Basic
21. a non USB technology Logo ona Ct different side Example non USB technology Logo displayed as LOGO USB Type C Port not to scale Note The Logo don ts guidelines apply to all of the Logo versions All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved 19 Example A SuperSpeed USB Trident Logo DisplayPort Logo SS SuperSpeed USB Power Delivery Trident Logo DisplayPort Logo ss lt D SuperSpeed USB 10 Gbps Power Delivery Trident Logo DisplayPort Logo Sse M gt All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved SuperSpeed USB Trident Logo MHL Logo SS KMEIL SuperSpeed USB Trident Logo MHL Logo Symbol SuperSpeed USB Power Delivery Trident Logo MHL Logo Ga MHL SuperSpeed USB Power Delivery Trident Logo MHL Logo Symbol All other trademarks are registered to their respective groups Example B 16 SuperSpeed USB 10 Gbps Power Delivery Trident Logo MHL Logo m MEL SuperSpeed USB 10 Gbps Power Delivery Trident Logo MHL Logo Symbol 2000 2014 USB Implementers Forum Inc USB IF All rights reserved
22. access to all of the electronic art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 19 10631825 3 EXHIBIT I USB IF SuperSpeed USB 10 Gbps logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF SuperSpeed USB 10 Gbps logo COMPANY will receive access to all of the electronic art files SUPERSPEED The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 20 10631825 3 EXHIBIT J USB IF SuperSpeed USB 10 Gbps Trident logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF SuperSpeed USB 10 Gbps Trident logo COMPANY will receive access to all of the electronic art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 21 10631825 3 EXHIBIT K USB IF USB Power Delivery Trident logo Do not reproduce this e
23. anuals 43 gt Art Files 44 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines General Logo Usage Guidelines Your company name logo or product name must appear on any products or related materials where the USB Logo s the USB ON THE GO Logo s the Wireless USB Logo s the SuperSpeed USB Logos the SuperSpeed USB 10 Gbps Logo s or the USB Power Delivery Logo s are used The Logos cannot be larger or more prominent than your product name trademark logo or company name You must use the logos exactly as they are shown in the USB IF digital artwork files you may not imitate the USB Logo s the USB ON THE GO Logo s the Wireless USB Logo s the SuperSpeed USB Logo s the SuperSpeed USB 10 Gbps Logo s or the USB Power Delivery Logo s in any of your materials You may not combine the USB Logo s the USB ON THE GO Logo s the Wireless USB Logo s the SuperSpeed USB Logo s the SuperSpeed USB 10 Gbps Logo s or the USB Power Delivery Logo s with any other feature including other marks words graphics photos slogans numbers design features or symbols The USB Logo s the USB ON THE GO Logo s the Wireless USB Logo s the SuperSpeed USB Logo s the SuperSpeed USB 10 Gbps Logo s or the USB Power Delivery Logo s may not be used as a design feature on any of your materials 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage G
24. ared to one printed using 4 color process or compared to an on screen RGB Logo PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc USB Red Use PANTONE 185C 4 color Cyan 0 Magenta 91 Yellow 76 Black 0 RGB Red 239 Green 62 Blue 66 yo g USB USB Blue Use PANTONE 653C Cyan 100 Magenta 62 Yellow 0 Black 20 RGB Red 0 Green 82 Blue 149 PANTONE 185C PANTONE 653C PANTONE 356C ON THE GO Green PANTONE 356C 4 color Cyan 95 Magenta 0 Yellow 100 Black 27 RGB Red 0 Green 133 Blue 63 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color Wireless USB Logo WIRELESS gt The USB IF Wireless USB Logo has been created as a 2 color Logo It is PANTONE 653C PANTONE 185C best to reproduce the Logo using the bu j PANTONE numbers shown at the right When reproducing these colors in 4 color process inks or on screen RGB the screen tints listed here should be used Different color models may reproduce the USB Red and USB Blue with slight color variations e g a Logo printed USB Red USB Blue using USB Red as a spot color may result in a slightly different hue of red Use PANTONE 189G pee Lemna when compared to one printed using 4 color 4 color 4 col
25. as a certification program i e the Mark s do not represent that USB IF certifies COMPANY S Product in any way b Upon passing the USB IF Test Procedure by COMPANY s Product and the posting of the Product on the USB IF Integrators List USB IF shall so notify COMPANY within thirty 30 days substantially in the form of the communication set forth in Exhibit N authorizing COMPANY to utilize the applicable Mark s c COMPANY agrees to ensure its Subsidiaries compliance with the terms and conditions of this License Agreement COMPANY agrees that it shall be jointly and severally liable for any breach of the terms and conditions of this License Agreement by such parties d USB IF represents and warrants that to the best of its knowledge it has the right to enter into this License Agreement including the right to license the Mark s e USB IF may modify the license right set forth in Section 2 a above to eliminate any country or jurisdiction from this License Agreement if USB IF determines in its reasonable judgment that use or continued use of the Mark s in such country or jurisdiction may subject USB IF or any third party to legal liability or may jeopardize USB IF s rights in the Mark s or any other USB IF trademarks in that or any other country or jurisdiction In such event and upon notice from USB IF COMPANY shall with reasonable promptness cease all use of the Mark s in such country or jurisdiction f COM
26. assemblies based on and compliant with the USB 2 0 specification and the USB IF Power Delivery specification the USB IF SuperSpeed USB Power Delivery Trident logo solely in conjunction with Product consisting of a cable and connector assembly that that signals at 5 Gbps and that delivers power over USB Veus that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB products and for USB Power Delivery products and that has been posted on the USB IF Integrators List the USB IF SuperSpeed USB Power Delivery Trident logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 0 USB 3 1 Gen1 and USB IF USB Power Delivery specifications the USB IF SuperSpeed USB 10 Gbps Power Delivery Trident logo solely in conjunction with Product consisting of a cable and connector assembly that that signals at 10 Gbps and that delivers power over USB 4 10631825 3 Vsus that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB 10 Gbps products and for USB Power Delivery products and that has been posted on the USB IF Integrators List and xviii the USB IF SuperSpeed USB 10 Gbps Power Delivery Trident logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 1 Gen2 and USB IF USB Power Delivery specifications The license right set forth in this Section 2 a is not intended
27. e attached Exhibit D v the USB IF Wireless USB logo for use with products based on the USB IF Wireless USB specification and that use and or interoperate with UWB radios that implement the PHY specification from the WiMedia Alliance and as depicted in the attached Exhibit E vi the USB IF Wireless USB GUI logo used on or in connection with a graphical user interface on host hardware implementation products and not on a device that meet all the requirements of Section 1 a v above where use of the USB IF Wireless USB logo set forth in Exhibit E is impracticable and as depicted in the attached Exhibit F vii the USB IF SuperSpeed USB logo for use with product that signals at 5 Gbps and as depicted in the attached Exhibit G viii the USB IF SuperSpeed USB Trident logo for use with product that signals at 5 Gbps and as depicted in the attached Exhibit H ix the USB IF SuperSpeed USB 10 Gbps logo for use with product that signals at 10 Gbps and as depicted in the attached Exhibit I and x the USB IF SuperSpeed USB 10 Gbps Trident logo for use with product that signals at 10 Gbps and as depicted in the attached Exhibit J xi the USB IF USB Power Delivery Trident logo for use with product that signals at 480 Mbps 12 Mbps or 1 5 Mbps and that delivers power over USB Vsus and as depicted in the attached Exhibit K xii the USB IF SuperSpeed USB Power Delivery Trident logo for use with product that signals at
28. en added to the 2 color version to ensure readability over a background of color PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc 2 Color Logo USB Red PANTONE 185C USB Blue PANTONE 653C 1 Color Logo Black Reverse Logo On a dark colored background 2 Color Logo On a dark colored background SUPERSPEED CERTIFIED SUPERSPEED CERTIFIED SUPERSPEED _ lt a USB al SUPERSPEED 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines SuperSpeed USB 10 Gbps Versions SuperSpeed USB 10 Gbps Logo The 2 color version is the preferred version of the USB IF SuperSpeed USB 10 Gbps Logo The 1 color black version of the SuperSpeed USB 10 Gbps Logo should be used for single color applications Choose either the reversed version of the SuperSpeed USB 10 Gbps Logo or the 2 color version when the SuperSpeed USB 10 Gbps Logo is used on a dark background A key line has been added to the 2 color version to ensure readability over a background of color PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc Logo Color 2 Color Logo USB Red PANTONE 185C USB Blue PANTONE 653C 1 Color Lo
29. en 82 standards Consult current PANTONE Color Publications for accurate color Blue 66 Blue 149 PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color SuperSpeed USB 10 Gbps Logo SUPERSPEED The USB IF SuperSpeed USB 10 Gbps bh PANTONE 185C Logo has been created as a 2 color Logo US B CERTIFIED Other color versions are shown on the following pages It is best to reproduce Qe PANTONE 653C the Logo using the PANTONE numbers 10 Gbps shown at the right When reproducing these colors in 4 color process inks or on screen RGB the screen tints listed here should be used Different color models may reproduce the USB Red and USB Blue with slight USB Red USB Blue color variations e g a Logo printed using USB Red as a spot color may Use PANTONE 185C Use PANTONE 653C result in a slightly different hue of color i l 4 color 4 color red when compared to one printed using Cyan 0 Cyan 100 4 color process or compared to an on Magenta 91 Magenta Boe Yellow 76 Yellow 0 screen RGB Logo Black 0 Black 20 RGB RGB Red 239 Red OO PANTONE Colors displayed here may not match PANTONE identified Green 62 Green 82 standards Consult current PANTONE Color Publications for accurate color Blue 66 Blue 149 PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All r
30. er the reversed version of the ON THE GO Basic Speed USB Logo or the 2 color USB Blue and ON THE GO Green version when the ON THE GO Basic Speed USB Logo is used on a dark background A key line has been added to the 2 color USB Blue and ON THE GO Green version to ensure readability over a background of color PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc Logo Color 2 Color Logo USB Blue PANTONE 653 ON THE GO Green PANTONE 356 CERTIFIED US f 1 Color Logo CERTIFIED US Black f Reverse Logo CERTIFIED US B On a dark colored background 2 Color Logo CERTIFIED On a dark colored background q 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color Hi Speed USB Versions z 2 Color Logo J BESDEED Mi Speed USE Logo USB Red PANTONE 185 USB The 2 color version is the preferred USB Blue PANTONE 653 version of the USB IF Hi Speed USB Logo The 1 color black version of the Hi Speed USB Logo should be used for kelinim pee single color applications ma CERTIFIED USB Choose either the reversed version of the Hi Speed USB Logo or the 2 color version when the Hi Speed USB Logo is used on a dark background A key line has been added to the 2 color Reverse Logo version to ensure readability over
31. f its reputation or trademarks USB IF shall be entitled to an immediate injunction in addition to any other legal or equitable remedies 16 HEADINGS Section headings are used in this License Agreement for convenience of reference only and shall not affect the meaning of any provision of this License Agreement 17 WAIVER No waiver of any breach of any provision of this License Agreement shall constitute a waiver of any prior concurrent or subsequent breach of the same or any other provision hereof and no waiver shall be effective unless made in writing and signed by an authorized representative of the waiving party 18 SEVERABILITY If any provision of this License Agreement or any other agreements incorporated herein shall be held by a court of competent jurisdiction to be illegal invalid or unenforceable the remaining provisions shall remain in full force and effect 19 RELATIONSHIP Neither this License Agreement nor any terms and conditions contained hereto shall be construed as creating a partnership joint venture or agency relationship or as granting a franchise USB IF is not a guarantor of the fitness or quality of the Products 20 SURVIVAL The provisions of Sections 2 g 5 8 b 9 10 12 13 15 and 18 shall survive expiration or termination of this License Agreement 10 10631825 3 21 EXHIBITS This License Agreement includes Exhibits A B C D E F G H I J K L M N and O that are hereb
32. ghts reserved USB Logo Usage Guidelines Logo Usage Hi Speed USB Versions These requirements apply to use of both the USB IF Hi Speed USB Logo and the USB IF ON THE GO Hi Speed USB Logo Clear Space Avoid visual clutter by maintaining a minimum amount of clear space around the Logo that is equal to the height of the blue bar that contains the word certified for the size selected Please note that when the Logo reverses out of a dark background it includes a key line around it The clear space does not include the key line Minimum Size for Print The minimum width of the Logos is 0 5 inch 13 mm and the minimum height for the USB Logo is 0 23 inch 5 85 mm and 0 29 inch 7 34 mm for the USB ON THE GO Logo Minimum Size for On Screen The minimum width of the Logo is 100 pixels The supplied on screen Logos are created with the clear space built into the files The smallest file available 100 pixels is set to the minimum size requirement and should not be scaled down Logo Position To position the Logo correctly use the left corner of the Logo as the vertical guideline Use the top edge of the Logo as the horizontal guideline A CERTIFIED 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Usage Wireless USB Version These requirements apply to use of the USB IF Wireless USB Logo Clear Space M Avoid visual clutter by ma
33. go Black Reverse Logo On a dark colored background 2 Color Logo On a dark colored background SUPERSPEED 10 Gbps SUPERSPEED 10 Gbps SUPERSPEED 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Don ts Proper use of the USB Logos strengthens its effectiveness each Don t place the Logo on a busy background A time they are seen The examples to busy background would not follow the clear space the right depict unacceptable uses of guidelines spelled out earlier in this document the USB Logos for both print and on screen applications Don t change the colors of the Logo Don t use any Hi Speed version of the Logos PaA without the word Hi Speed CERTIFI P B I 2 a Note The Logo don ts guidelines apply to all of the Logo versions 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Don ts Don t use any version of the Logos without the word certified Don t use the Logo without the trademark CERTIFI or symbol A lt Don t use the ON THE GO Logos without the words On The Go CERTIFI Note The Logo don ts guidelines apply to all of the Logo versions 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Don ts Don t use the wireless Logo without the
34. greement c From and after termination of this License Agreement COMPANY shall cease and desist from all use of the Mark s However unless the License Agreement is terminated for breach in connection with more than a single Product COMPANY may distribute then existing units of complying Product and advertising materials containing the Mark s for a period of six 6 months from the termination date provided use of the Mark s in connection with such inventory and such inventory is in compliance with the terms and conditions of this License Agreement 13 NOTICES All notices and other communications under this License Agreement shall be in writing and shall be deemed given if delivered personally mailed by registered or certified mail return receipt requested or sent by email or telecopy with a receipt confirmed by telephone to the parties at the addresses herein or to such other addresses as a party may from time to time notify the other parties Provision of an email address at which each party may be contacted is mandatory USB IF USB Implementers Forum Inc 3855 SW 153rd Drive Beaverton OR 97003 USA Telephone 503 619 0426 Fax 503 644 6708 email Address admin usb org COMPANY Information listed at the top of this Agreement 14 ENTIRE LICENSE AGREEMENT AMENDMENT USB IF providing this License Agreement to COMPANY does not constitute an offer by USB IF Upon execution by both USB IF and COMPANY this License Ag
35. he interconnect market USB can be found everywhere from PCs to consumer electronics to mobile devices Because of its ease of use speed and expandability USB is the preferred connection for many consumers This presents a continued market opportunity for the future In order to realize this opportunity USB products must continue to enhance the consumers experience through high quality and ease of use That s why the USB Implementers Forum Inc developed a trademark protected USB Logo s USB ON THE GO Logo s Wireless USB Logo s SuperSpeed USB Logo s SuperSpeed USB 10 Gbps Logo s and USB Power Delivery Logo s for use by qualified parties To qualify for the right to display these logos products must pass the specified USB IF compliance testing for product quality 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Table of Contents P Logos 4 1 gt Logo Usage 12 20 Basic Speed USB Versions 12 Hi Speed USB Versions 13 Wireless USB Version 14 15 SuperSpeed USB Version 16 SuperSpeed USB 10 Gbps Version 17 SuperSpeed USB Trident 18 SuperSpeed USB 10 Gbps Trident 19 USB Power Delivery Logos 20 P Logo Color 21 33 Basic Speed USB Versions 21 27 28 Hi Speed USB Versions 22 23 29 30 Wireless USB Version 24 31 SuperSpeed USB Version 25 32 SuperSpeed USB 10 Gbps Version 26 33 gt Logo Don ts 34 38 P Layout 39 43 Packaging 40 Collateral 41 Advertisements 42 M
36. ights reserved USB Logo Usage Guidelines Logo Color Basic Speed USB Versions Basic Speed USB Logo 1 Color Logo ETIE The USB IF Basic Speed USB Logo has a eae USE been created as a 1 color Logo The 1 color USB Blue version is the preferred version of the Basic Speed USB Logo The 1 color black version of the Basic 1 Color L Speed USB Logo should be used for a a CERTIFIED USB single color applications e Choose either the reversed version of the Basic Speed USB Logo or the 1 color USB Blue version when the Basic Speed USB Logo is used on Reverse Logo a dark background A key line has On a dark colored background been added to the 1 color USB Blue version to ensure readability over a background of color 1 Color Logo CERTIFIED USB On a dark colored background PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Basic Speed USB Versions ON THE GO USB Logo The USB IF ON THE GO USB Logo for Basic Speed has been created as a 2 color Logo The 2 color version USB Blue and ON THE GO Green is the preferred version of the ON THE GO USB Logo The 1 color black version of the ON THE GO Basic Speed USB Logo should be used for single color applications Choose eith
37. ing may be placed around the edge corner of the device or on the top side edge of a device above the USB Type C Port Around the Edge Corner of a Device i ma ax A Logo Grouping may be placed around the edge of the device if 10 nn oa the USB Type C Port is a maximum of 10mm 39 inches or closer to the edge corner of the device where the Logos will be placed around The Logo Grouping must also be placed a maximum of 10mm 39 inches or closer from the edge corner of the device where the USB Type C Logo is placed around max 10 mm Top Side Edge of a Device Top Side Edge of a Device A Logo Grouping may be placed on the top side edge of a device if the S060 USB Type C Port is a maximum of 10mm 39 inches or closer to the top side of the device where the Logo will be placed above The Logo Grouping then must also be placed a maximum of 10mm 39 inches or closer from the top side edge of the device where the USB Type C Logo is placed below C Representative of USB Type C Port Example non USB technology Logo displayed as LOGO All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Logo Placement USB Logos cannot be placed on the back front corner of a product if a non USB technology Logo is adjacent to the USB Type C Port If any Logos can be p
38. intaining a minimum amount of clear space around the Logo that is equal to the height of the blue bar that contains the word certified for the size selected Please note that when the Logo reverses out of a dark background it includes a key line around it The clear space does not include the key line iin ae SB J Minimum Size for Print gt WIRELESS z The minimum width of the Logo is 0 75 inch USB 19 mm and the minimum height for the i Logo is 0 39 inch 9 9 mm Minimum Size for On Screen Eo The minimum width of the Logo is 125 pixels WIRELESS The supplied on screen Logos are created with l the clear space built into the files The smallest Ca A file available 125 pixels is set to the minimum size requirement and should not be scaled down Logo Position N g WIRELESS a z To position the Logo correctly use the left corner ee i ab of the Logo as the vertical guideline Use the top edge of the USB letters as the horizontal guideline 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Usage Wireless USB Graphical Minimum Size for GUI EN EN a User Interface GUI Version The smallest file available 43 x 23 pixels is set to USB E 23 pixels the minimum size requirement and should not be 43 pixels This requirement applies to use of scaled up or down the USB IF Wireless USBGUILogo mg g 2000 2014 USB
39. istered to their respective groups All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts Logo Don ts and Devices that Support Alternate Modes Don t place the Logo on the bottom surface of a Product or its packaging Don t obstruct the Logo with labels or other graphics Don t reproduce USB Type C Port Logos in other colors than white black molded or engraved Don t use more than four Logos in a Logo ss LOGO 676 JGOLOGO Grouping including the USB Logo Example non USB technology Logo displayed as LOGO USB Type C Port not to scale Note The Logo don ts guidelines apply to all of the Logo versions All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Don t make the non USB technology Logo larger SS a in height than a USB Logo Don t place a USB Logo to the right of a Logo Grouping LO G 0 LO G 0 LO G Ze Don t place a USB Logo in the middle of a Logo Grouping LO G e 0 G 0 LO G 0 Don t place a non USB technology Logo next to a USB Type C Port without the appropriate USB Cc HG Logo Don ts Logo included in a proper Logo Grouping Don t place a USB Logo on one side of a USB Type C Port with
40. ith non USB technology Logo s This is called a Logo Grouping The SuperSpeed USB 10 Gbps Trident Logo may be used solely in conjunction with Product as defined in the USB Logo Usage Guidelines The SuperSpeed USB 10 Gbps Power Delivery Trident Logo is for use with a USB Type C Port that delivers power over USB VBUS as defined in the USB Logo Usage Guidelines All other trademarks are registered to their respective groups SuperSpeed USB 10 Gbps Trident Logo Non USB Technology Logo ss LOGO SuperSpeed USB 10 Gbps Power Delivery Trident Logo Non USB Technology Logo a LOGO Example non USB technology Logo displayed as LOGO 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts Logo Grouping and Devices that Support Alternate Modes Logo Grouping Logo Grouping displaying three non USB Technology Logos To properly identify that a USB Type C Port supports Alternate Mode s the SuperSpeed USB Trident Logo the SuperSpeed USB 10 Gbps SS LO 0 LO G 0 LO G 0 Trident Logo or USB Power Delivery Trident ea i wea nl ee Logos may be positioned side by side with 1 3 f non USB technology Logo s This is called a Logo Grouping A USB Logo may not be grouped with more than three non USB technology Logo s Example non USB technology Logo displayed as LOGO USB Type C Port not to scale All other trademarks are registered to their respective group
41. k s in connection with Product at any time upon thirty 30 days notice from USB IF COMPANY shall cooperate fully with USB IF to facilitate periodic review of COMPANY s use of the Mark s and of COMPANY s compliance with the quality standards described in this License Agreement and the attached Exhibit O In any periodic review of COMPANY s compliance Product will be tested under the compliance requirements that were in effect when Product was last submitted to the USB IF Test Procedure c If USB IF in its sole discretion determines that any use of the Mark s or that the quality of any Product submitted to USB IF for quality control purposes fails to conform to this License Agreement USB IF shall provide the COMPANY with written notice of such failure or deficiency The COMPANY shall have sixty 60 days thereafter to satisfy USB IF that the COMPANY has fully corrected and remedied any such deficiencies Should the COMPANY fail to cure the deficiencies within said sixty 60 day period USB IF may terminate this License Agreement with respect to such deficient Product d COMPANY represents and warrants that the representative sample of the specific model or version of COMPANY s Product submitted to USB IF for testing accurately represents the specific model or version of COMPANY s Product at all times Product is available during the term of this License Agreement e COMPANY represents and warrants that it will comply with all app
42. l non USB technology Logos within the Logo Grouping should be scaled proportionately to equal the height of the USB Logo Non USB technology Logos should not be greater in height than the USB Logo Logo Position Logo Groupings should be centered horizontally to the USB Type C Port when placed above or below the Port or centered vertically to the USB Type C Port when placed to the right or to the left of the Port Logo Orientation When placed adjacent to the USB Type C Port SuperSpeed USB Trident Logos and USB Power Delivery Trident Logos can be oriented horizontally with the large circle or SS on the left All other trademarks are registered to their respective groups Placement of Logo Grouping above or below the USB Type C Port Logo Grouping ss lt LOGOLOGO Horizontally centered SS LOGOLOGO Logo Grouping Horizontally centered Placement of Logo Grouping to the right or to the left of the USB Type C Port Logo Grouping ss lt LOGOLOGO oe Logo Grouping ct Ss lt LOGOLOGO Example non USB technology Logo displayed as LOGO USB Type C Port not to scale 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Kojo Placement If the space above below to the right or to the Around the Edge Corner of a Device left of the USB Type C Port is less than the space required by the Logo Grouping a Logo Group
43. laced adjacent to the USB Type C Port the Logo Grouping must include the appropriate USB Logo C Representative of USB Type C Port Example non USB technology Logo displayed as LOGO All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts Logo Placement and Devices that Support Alternate Modes Logo Usage In some situations where space is limited a device may not support the ability to display a USB Logo or Logo Grouping Where the SuperSpeed USB Trident Logo the SuperSpeed USB 10 Gbps Trident Logo or the USB Power Delivery Trident Logos have been omitted on the printing engraving on Product chassis adjacent to the USB Type C Port the manufacturer Licensees must include the following statement s in their user s manual packaging printed materials accompanying the Product The USB Power Delivery Logos are registered trademarks of USB Implementers Forum Inc and or The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers Forum Inc and or The SuperSpeed USB 10 Gbps Trident Logo is a registered trademark of USB Implementers Forum Inc The statement s must be accompanied with the proper USB Power Delivery Tridents SuperSpeed USB Trident or SuperSpeed USB 10 Gbps Trident Logos with the correct rendering of the or All other trademarks are reg
44. lease note that the trademark and the word certified are integral parts of the Logos They are considered part of the Logo art and should not be altered in any way The Logos must be reproduced from the USB IF digital artwork files 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines The USB IF SuperSpeed USB Logo is available with and without the plus and 10 Gbps labels The SuperSpeed USB Logo must be used solely in conjunction with Product that signals at 5 Gbps that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB products and that has been posted on the USB IF Integrators List The SuperSpeed USB 10 Gbps Logo must be used solely in conjunction with Product that signals at 10 Gbps that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB 10 Gbps products and that has been posted on the USB IF Integrators List The SuperSpeed USB Logo may be reproduced only in the versions shown in this document and may not be altered in any way Please note that the trademark and the word certified are integral parts of the Logos They are considered part of the Logo art and should not be altered in any way The Logos must be reproduced from the USB IF digital artwork files The SuperSpeed USB 10 Gbps Logo may be reproduced only in the versions shown in this document and may not be altered in any way
45. licable laws rules and regulations regarding promotion and sale of Product with any of the Marks and will not violate or infringe any right of any third party 8 IDENTIFICATION AND USE a COMPANY shall mark every use of the Mark s with the trademark designation as described in Exhibit O and shall otherwise comply with USB Logo Usage Guidelines as amended by USB IF from time to time with reasonable notice b COMPANY acknowledges USB IF s ownership of the Marks COMPANY shall employ best efforts to use the Mark s in a manner that does not derogate from USB IF s rights in any of the Marks and will take no action that will interfere with or diminish USB IF s rights in the Marks COMPANY agrees not to adopt use or register any corporate name trade name trademark domain name product name service mark or certification mark or other designation similar to the Mark s COMPANY agrees that all use of the Mark s by COMPANY will inure to the benefit of USB IF COMPANY may not use the Mark s in any way that implies endorsement or sponsorship by USB IF of COMPANY s Product or services 10631825 3 9 DEFENSE OF CLAIMS a In the event USB IF receives information concerning an intellectual property infringement claim related to the Mark s USB IF may at its expense without obligation to do so either i procure for COMPANY the right to continue to use the alleged infringing Mark s as set forth in Section 2 a or ii replace or
46. modify the Mark s to make it non infringing and in which case COMPANY shall with reasonable promptness thereafter cease use of the alleged infringing Mark s b USB IF shall have no liability for any intellectual property infringement claim based on COMPANY s manufacture or distribution of Product or its use of the Mark s c USB IF MAKES NO WARRANTIES EITHER EXPRESS IMPLIED STATUTORY OR OTHERWISE WITH RESPECT TO THE MARK S INCLUDING ANY WARRANTY OF NON INFRINGEMENT IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE d COMPANY agrees to indemnify and defend USB IF from and against any and all claims damages costs and expenses including reasonable attorneys fees and pay the amount of any adverse final judgment or settlement to which both parties consent arising out of or related to the Product in any manner including user claims regarding Product s defect failure or malfunction provided COMPANY is notified promptly in writing of any claim and COMPANY has sole control over its defense or settlement 10 CONSEQUENTIAL ET AL DAMAGES EXCEPT AS SET FORTH IN PARAGRAPH 9 d NEITHER PARTY SHALL BE LIABLE FOR ANY CONSEQUENTIAL INCIDENTAL INDIRECT PUNITIVE OR SPECIAL DAMAGES INCLUDING LOSS OF BUSINESS PROFITS ARISING FROM OR RELATED TO COMPANY S MARKETING OR DISTRIBUTION OF PRODUCT OR ANY USE OF THE MARK S REGARDLESS OF WHETHER SUCH LIABILITY IS BASED ON BREACH OF CONTRACT TORT STR
47. nditioned upon compliance with the terms and conditions of this License Agreement USB IF hereby grants to COMPANY and any applicable Subsidiaries of COMPANY a nonexclusive personal right including through manufacturing and distribution agents of COMPANY and Subsidiaries to use in the Territory solely in the manner described in the USB Logo Usage Guidelines set forth in the attached Exhibit J and as may be amended by USB IF from time to time with reasonable notice i the USB IF Basic Speed USB logo solely in conjunction with Product that signals at 12 Mbps or 1 5 Mbps that has been submitted to and passed the USB IF Test Procedure for Basic Speed USB products and that has been posted on the USB IF Integrators List 11 the USB IF Hi Speed USB logo solely in conjunction with Product that signals at 480 Mbps that has been submitted to and passed the USB IF Test Procedure for Hi Speed USB products and that has been posted on the USB IF Integrators List iii the USB IF ON THE GO Basic Speed USB logo solely in conjunction with Product that signals at 12 Mbps or 1 5 Mbps that has been submitted to and passed the ON THE GO USB IF Test Procedure for Basic Speed USB products and that has been posted on the USB IF Integrators List iv the USB IF ON THE GO Hi Speed USB logo solely in conjunction with Product that signals at 480 Mbps that has been submitted to and passed the ON THE GO USB IF Test Procedure for Hi Speed USB products and
48. or reverse or full color versions of the Logo choosing the Logo that works Super Speed best with the design of the ad No Interference 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Manuals Where the or symbols of the USB IF SuperSpeed USB Trident Logo the USB IF SuperSpeed USB 10 Gbps Trident Logo or the USB IF USB Power Delivery Logos have been omitted on User s Manual the printing engraving on Product chassis the manufacture Licensees must include the following statement s in their user s manual printed materials accompanying the Product The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers Forum Inc or The SuperSpeed USB 10 Gbps Trident Logo is a registered trademark of USB Implementers Forum Inc or The USB Power Delivery Trident Logos are trademarks of USB Implementers Forum Inc The SuperSpeed USB Trident Logo is a registered S S trademark of USB Implementers Forum Inc The statement s must be accompanied with the proper USB Power Delivery SuperSpeed USB Trident or SuperSpeed USB 10 Gbps Trident image of the mark s with the correct rendering of the or 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Art Files The USB Logo s the ON THE GO USB Logo s the Wireless USB Logo s the SuperSpeed USB Logo s the SuperSpeed
49. or process or compared to an on Cyan 0 Cyan 100 Magenta 91 Magenta 62 screen RGB Logo Gick 76 Yellow 0 Black 0 Black 20 RGB RGB Red 239 Red 0 PANTONE Colors displayed here may not match PANTONE identified Green 62 Green 82 standards Consult current PANTONE Color Publications for accurate color Blue 66 Blue 149 PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color SuperSpeed USB Logo SUPERSPEED The USB IF SuperSpeed USB Logo E PANTONE 185C has been created as a 2 color Logo US B CERTIFIED Other color versions are shown on the following pages It is best to reproduce Qa PANTONE 653C the Logo using the PANTONE numbers ss shown at the right When reproducing these colors in 4 color process inks or on screen RGB the screen tints listed here should be used Different color models may reproduce the USB Red and USB Blue with slight USB Red USB Blue color variations e g a Logo printed using USB Red as a spot color may Use PANTONE 185C Use PANTONE 653C result in a slightly different hue of red 4 color 4 color when compared to one printed using Cyan 0 Cyan 100 4 color process or compared to an on Magenta 91 Magenta Boe Yellow 76 Yellow 0 screen RGB Logo Black 0 Black 20 RGB RGB Red 239 Red 0 PANTONE Colors displayed here may not match PANTONE identified Green 62 Gre
50. or use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 16 10631825 3 EXHIBIT F USB IF Wireless USB GUI Logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF Wireless USB GUI Logo COMPANY will receive access to all of the electronic art files 55 The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 17 10631825 3 EXHIBIT G USB IF SuperSpeed USB logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF SuperSpeed USB logo COMPANY will receive access to all of the electronic art files SUPERSPEED CERTIFIED The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 18 10631825 3 EXHIBIT H USB IF SuperSpeed USB Trident logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF SuperSpeed USB Trident logo COMPANY will receive
51. reement including all Exhibits contains the entire agreement of the parties with respect to the subject matter hereof and shall supersede and merge all prior and contemporaneous communications It shall not be amended except by a written agreement subsequent to the Effective Date and signed on behalf of the parties by their respective authorized representatives 9 10631825 3 15 GOVERNING LAW ATTORNEYS FEES EQUITABLE RELIEF a This License Agreement shall be governed by and construed in accordance with the laws of the State of California and the applicable federal laws COMPANY hereby consents to jurisdiction and venue in the state and federal courts sitting in the State of California in the Northern District of California The parties agree to accept service of process by U S certified or registered mail return receipt requested or by any other method authorized by applicable law b If either party employs attorneys to enforce any rights arising out of or related to this License Agreement the prevailing party shall be entitled to recover its reasonable attorneys fees costs and other expenses c COMPANY acknowledges that a breach by it of this License Agreement may cause USB IF irreparable damage which cannot be remedied by monetary damages in an action at law and may also constitute infringement of the Mark s In the event of any breach that could cause irreparable harm to USB IF or cause some impairment or dilution o
52. rident Logo Please note that the SuperSpeed USB 10 Gbps Trident Logo is only to be used on cables and devices dia Q Clear Space Avoid visual clutter by maintaining a minimum 1 0 amount of clear space around the Logo that is equal to the width of the square of the trident for the size selected Minimum Sizes The minimum size of the largest dimension of the Logo is 5mm 0 2 inches Measurement does not include the Logo Position The Logo can be oriented horizontally with the SS on the left or vertically with the SS at the bottom Licensee is not obligated to use the Circle R and may omit the registered trademark symbol on the SuperSpeed USB 10 Gbps Trident Logo for mobile and non mobile Product for which the Licensee is printing engraving on chassis where the reasonable alternatives for the location and size of the Logo do not allow for the symbol to have a maximum dimension of 15mm or more This permission is limited only to these exact situations Where the symbol is so omitted the manufacture Licensees must include the following statement in their user s manual printed materials accompanying the Product The SuperSpeed USB 10 Gbps Trident Logo is a registered trademark of USB Implementers Forum Inc and must be accompanied with the image of the mark with the correct rendering of the 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage
53. rident logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 0 and USB 3 1 Gen1 specifications the USB IF SuperSpeed USB 10 Gbps logo solely in conjunction with Product that signals at 10 Gbps that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB 10 Gbps products and that has been posted on the USB IF Integrators List and the USB IF SuperSpeed USB 10 Gbps Trident logo solely in conjunction with Product consisting of a cable and connector assembly that signals at 10 Gbps that has been submitted to and passed the USB IF Test Procedure for SuperSpeed USB 10 Gbps products and that has been posted on the USB IF Integrators List the USB IF SuperSpeed USB 10 Gbps Trident logo solely in conjunction with product other than cable and connector assemblies based on and compliant with the USB 3 1 Gen2 specification the USB IF USB Power Delivery Trident logo solely in conjunction with Product consisting of a cable and connector assembly that that signals at 480 Mbps 12 Mbps or 1 5 Mbps and that delivers power over USB Vgus that has been submitted to and passed the USB IF Test Procedure for Basic Speed USB or Hi speed USB products as applicable and for USB Power Delivery products and that has been posted on the USB IF Integrators List the USB IF USB Power Delivery Trident logo solely in conjunction with product other than cable and connector
54. rum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Introduction The USB Type C specification defines Functional Extensions that enable USB Type C hosts and devices to support optional capabilities The Functional Extensions include Alternate Modes Alt Mode an option that permits a vendor or standards organization to provide additional features within USB Type C hosts and devices These logo guidelines were created for vendors and standards organizations implementing Alternate Modes on USB Type C hosts and devices that have obtained a standard or vendor ID SVID assigned by the USB Implementers Forum USB IF These guidelines outline the proper Logo Groupings Logo Order Logo Clear Space and Logo Placement required for USB Type C Ports on hosts and devices featuring Alternate Mode s capabilities The USB Logos can only be used solely in conjunction with Product as defined in the USB Logo Usage Guidelines All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes To provide the best user experience it is recommended that all SuperSpeed USB Trident Logo USB Type C Ports on hosts and devices that
55. s 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Logo Order Logo Order Logo Order with USB Logo always displayed to the left When the the SuperSpeed USB Trident Logo the SuperSpeed USB 10 Gbps Trident Logo f pi SuperSpeed USB Power Delivery Trident Logo SS Q LOG 0 LOG 0 or a SuperSpeed USB 10 Gbps Power Delivery NE O VU SJ Trident Logo is grouped with a non USB pid E technology Logo s it is required that the USB Logo appear as the furthest Logo to the left of the entire Logo Grouping Within a Logo Grouping the SuperSpeed USB Trident Logo the SuperSpeed USB 10 Gbps Trident Logo or USB Power Delivery Trident Logos should NOT be placed in between or to the right of any non USB technology Logo s All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Logo Clear Space Logo Clear Space These requirements apply to use of the SuperSpeed USB Trident Logo the SuperSpeed USB 10 Gbps Trident Logo and the USB Power Delivery Trident Logos when grouped with a non USB technology Logo s Logo Clear Space When the USB Logos are used avoid visual clutter by maintaining a minimum amount of clear space around the Logos that is equal to the
56. screen RGB the screen tints listed here should be used Different color models may reproduce the USB Red and USB Blue with slight USB Red USB Blue color variations e g a Logo printed using USB Red as a spot color may Use PANTONE 185C Use PANTONE 653C result in a slightly different hue of red i 4 color 4 color when compared to one printed using Cyn 0 Cyan 100 4 color process or compared to an on Magenta 91 Magenta Bee Yellow 76 Yellow 0 screen RGB Logo Black 0 Black 20 RGB RGB Red 239 Red OO PANTONE Colors displayed here may not match PANTONE identified Green 62 Green 82 standards Consult current PANTONE Color Publications for accurate color Blue 66 Blue 149 PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color ON THE GO Hi Speed USB Logo The USB IF ON THE GO Hi Speed USB Logo has been created as a 3 color Logo Other color versions are shown on the following pages It is best to reproduce the Logo using the PANTONE numbers shown at the right When reproducing these colors in 4 color process inks or on screen RGB the screen tints listed here should be used Different color models may reproduce the USB Red and USB Blue and the ON THE GO Green with slight color variations e g a Logo printed using USB Red as a spot color may result in a slightly different hue of red when comp
57. support Alternate Non USB Technology Logo Modes and have obtained a SVID assigned by the USB IF should be prominently identified SSA LO G 0 To visually display that a USB Type C Port supports an Alternate Mode s the SuperSpeed USB Trident Logo or SuperSpeed USB Power Delivery Trident Logo may be positioned side by side with non USB technology logo s This is called a Logo Grouping SuperSpeed USB Power Delivery Trident Logo The SuperSpeed USB Trident Logo may be used solely in conjunction Non USB Technology Lago with Product as defined in the USB Logo Usage Guidelines The SuperSpeed USB Power Delivery Trident Logo is for use with a USB Type C Port that delivers power over USB Veus as defined in CA S LO G 0 the USB Logo Usage Guidelines Example non USB technology Logo displayed as LOGO All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes To provide the best user experience it is recommended that all USB Type C Ports on hosts and devices that support Alternate Modes and have obtained a SVID assigned by the USB IF should be prominently identified To visually display that a USB Type C Port supports an Alternate Mode s the SuperSpeed USB 10 Gbps Trident Logo or Superspeed USB 10 Gbps Power Delivery Trident Logo may be positioned side by side w
58. the USB IF SuperSpeed USB 10 Gbps Logo Clear Space SUPERSPEED Avoid visual clutter by maintaining a minimum amount of clear space around the Logo that is equal to the height of the white space that CERTIFIED USB contains the word certified for the size selected Please note that when the Logo reverses out of a dark background it includes a key line around it The clear space does not include the key line Minimum Size for Print eee The minimum width of the Logo is 0 75 inch USB 19 mm and the minimum height for the Logo is 0 4 inch 10 16 mm Minimum Size for On Screen The minimum width of the Logo is 125 pixels The supplied on screen Logos are created with the clear space built into the files The smallest file available 125 pixels is set to the minimum size requirement and should not be scaled down SUPERSPEED a CERTIFIED USB 10 Gbps Logo Position To position the Logo correctly use the upper left corner top arrow as the vertical guideline Use the top edge of the word SUPERSPEED as the horizontal guideline SUPERSPEED CERTIFIED USB 10 Gbps 9 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Usage SuperSpeed USB Trident Logo These requirements apply to use of the USB IF SuperSpeed USB Trident Logo Please note that the SuperSpeed USB Trident Logo is only to be used on cables and devices
59. ts reserved USB Logo Usage Guidelines Logo Color Wireless USB Versions EN 2 Color Logo WREE Wireless USB Logo USB Red PANTONE 185C USB The 2 color version is the preferred USB Blue PANTONE 653C version of the USB IF Wireless USB Logo The 1 color black version of the Wireless USB Logo should be used for i ere WIRELESS single color applications CelueLoge Choose either the reversed version of oe ams J the Wireless USB Logo or the 2 color S version when the Wireless USB Logo is used on a dark background A key line has been added to the 2 color ee version to ensure readability over a Reverse Logo AS B background of color On a dark colored background y 2 Color Logo On a dark colored background U SB PANTONE Colors displayed here may not match PANTONE identified standards Consult current PANTONE Color Publications for accurate color PANTONE is the property of Pantone Inc 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines Logo Color SuperSpeed USB Versions SuperSpeed USB Logo The 2 color version is the preferred version of the USB IF SuperSpeed USB Logo The 1 color black version of the SuperSpeed USB Logo should be used for single color applications Choose either the reversed version of the SuperSpeed USB Logo or the 2 color version when the SuperSpeed USB Logo is used on a dark background A key line has be
60. uidelines The USB IF Basic Speed USB Logo and Basic Speed USB Versions the USB IF ON THE GO Basic Speed mmm 6 Ay USB Logo are available with and without the Hi Speed USB label The Basic Speed USB Logo and the ON THE GO USB Logo must be used with Basic Speed 12 Mbps or 1 5 Mbps Product The Hi Speed USB Logo and the ON THE GO USB Logo must be used with Hi Speed 480 Mbps Product THE HI SPEED VERSIONS OF THE LOGOS CANNOT Hi Speed USB Versions BE USED WITH BASIC SPEED PRODUCT The Basic Speed USB Logo and the ON THE GO USB Logo may be reproduced only in the versions shown in this document and may not be altered in any way Please note that the trademark amp and the word certified are integral parts of the Logos They are considered part of the Logo art and should not be altered in any way The Logos must be reproduced from the USB IF digital artwork files CERTIFIED CERTIFIED CERTIFIED 2000 2014 USB Implementers Forum Inc USB IF All rights reserved USB Logo Usage Guidelines The USB IF Wireless USB Logo must Wireless USB Version eee be used only with Product based on the USB IF Wireless USB specification and that use and or interoperate 9 fo with UWB radios that implement the MAC and PHY specifications from the WiMedia Alliance The Wireless USB Logo may be reproduced only in the versions shown in this document and may not be altered in any way P
61. upon execution of same 5 GENERIC TERMS COMPANY understands that USB IF takes the position that the terms USB USB Wireless and Universal Serial Bus when used in connection with any USB device are generic collectively the Generic Terms COMPANY agrees not to attempt to acquire or assert any exclusive trademark rights in the Generic Terms COMPANY may file trademark applications for a trademark incorporating any of the Generic Terms provided that the Generic Terms are expressly disclaimed to the fullest extent possible under law COMPANY further agrees that it will not assert against any person or entity any trademark trade name or similar rights it may now have or hereafter acquire in the Generic Terms 6 LOGO ADMINISTRATION FEE If COMPANY is not a USB IF member it shall pay a logo administration fee of Three Thousand Five Hundred Dollars 3 500 00 upon COMPANY s execution of this Agreement No logo administration fee shall be required from USB IF members 10631825 3 7 QUALITY INSPECTION AND APPROVAL a COMPANY represents and warrants that to the best of its knowledge Product is in compliance with the USB specification and COMPANY agrees to maintain the quality of Product at least at a level that meets industry standards and is commensurate with the quality of Product previously distributed by COMPANY b COMPANY shall supply USB IF with suitable samples of Product and COMPANY s use of the Mar
62. ved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Logo Placement Logo Placement in Relation to a USB Type C Port Vertical Horizontal l i l e seancet To provide the best user experience i MOR Below Above se 1080 is recommended that all USB Type C Ports on hosts and devices that support Alternate Modes and have obtained a SVID assigned by the USB IF should ss lt L0G0 ss 0G0C_ be prominently identified with a Logo Below Sze emudelcece fe E E l iaa Gramineae need atowe CC below to the left or to the right of the Left Right Left a ae USB Type C Port ee ee If a USB Type C port is vertical on a host l 1 l ee ee hub or device rotate the USB and non Right J seo USB technology Logos so that they are etcetera parallel with the long side of the port CD Representative of USB Type C Port Example non USB technology Logo displayed as LOGO All other trademarks are registered to their respective groups 2000 2014 USB Implementers Forum Inc USB IF All rights reserved Logo Guidelines for USB Type C Ports on Hosts and Devices that Support Alternate Modes Logo Placement Logo Placement in Relation to a USB Type C Port These requirements apply to the use of the SuperSpeed USB Trident Logo the SuperSpeed USB 10 Gbps Trident Logo and the USB Power Delivery Trident Logos when grouped with non USB technology Logo s Logo Height Al
63. width of the square on the trident symbol If the USB Power Delivery Trident Logos are used maintain a minimum amount of clear space around the logo that is equal to the width of the battery terminal for the size selected Non USB Technology Logo Clear Space Logo Groupings should consider minimum clear space for each individual technology Logo If a non USB technology Logo All other trademarks are registered to their respective groups guidelines specify a clear space that is wider than the width needed for the corresponding USB Logo then the clear space between the Logos should be the minimum required by the non USB technology Logo If anon USB technology Logo requires a wider clear space than that required by the USB Logo the clear space between all Logos in the Logo Grouping should be based on the Logo that specifies the widest amount of clear space For consistent spacing the amount of Logo Clear Space should be used between each of the Logos displayed adjacent to the USB Type C Port Logo Clear Space based on the SuperSpeed USB Trident Logo SSS LOGOLOGO Gate OGOLOGO Logo Clear Space based on non USB Technology Logo s Clear Space minimum If required to be wider than USB Logo clear space Example Clear space based on half of the height of the letter L in the word LOGO Example non USB technology Logo displayed as LOGO 2000 2014 USB Implementers Forum Inc USB IF All rights reser
64. xample Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF USB Power Delivery Trident logo COMPANY will receive access to all of the electronic art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 22 10631825 3 EXHIBIT L USB IF SuperSpeed USB Power Delivery Trident logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF Super Speed USB Power Delivery Trident logo COMPANY will receive access to all of the electronic art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 23 10631825 3 EXHIBIT M USB IF SuperSpeed USB 10 Gbps Power Delivery Trident logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF SuperSpeed USB 10 Gbps Power Delivery Trident logo COMPANY will receive access to all of the electronic art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo
65. y incorporated by reference IN WITNESS WHEREOF the parties hereto have executed this License Agreement as of the Effective Date and do each hereby warrant and represent that their respective signatory whose signature appears below has been and is on the date of this License Agreement duly authorized by all necessary and appropriate corporate action to execute this License Agreement USB IMPLEMENTERS FORUM INC COMPANY Name Signature Name Signature Name Print Name Print Title Title Date Date 11 10631825 3 EXHIBIT A USB IF Basic Speed USB Logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF Basic Speed UBS Logo COMPANY will receive access to all of the electronic logo art files CERTI The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo Trademark footnote The USB IF Logos are trademarks of USB Implementers Forum Inc 12 10631825 3 EXHIBIT B USB IF Hi Speed USB Logo Do not reproduce this example Upon execution of the USB IF Trademark License Agreement and qualifying to use the USB IF Hi Speed USB Logo COMPANY will receive access to all of the electronic logo art files The logo reproduced above has been protected with a not for use badge printed across it This not for use badge is not part of the logo

USB-IF Trademark License Agreement

Contents

Download Pdf Manuals

Related Search

Related Contents