Home

3 Sixty 2R - Performance Audio

1. XLR Pin Configuration Pin 1 Ground Pin 2 Data Compliment negative AAR Pin 3 Data True positive Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems 0 and interference It is always advisable G X p to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX g and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 14 3 Sixty 2R Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal
2. 0 255 LEFT TILT MOVEMENT 8bit Master Slave Operation Sound Active or Auto Program This function will allow you to link up to 16 units together and oper l as RIGHT TILT MOVEMENT 8bit ate without a controller The units can run a built in program or run in sound actiive mode In Master Slave operation one unit will act as the LEFT COLOR WHEEL controlling unit and the others will react to the controlling units pro OPEN grams Any unit can act as a Master or as a Slave 9 17 COLOR 1 1 Using standard XLR microphone cables daisy chain your units 18 26 COLOR 2 together via the XLR connector on the rear of the units Remem 27 35 COLOR 3 ber the Male XLR connector is the input and the Female XLR 36 44 COLOR 4 connector is the output The first unit in the chain master will use 45 53 COLOR 5 the female XLR connector only The last unit in the chain will use 54 62 COLOR 6 the male XLR connector only For longer cable runs we suggest a 63 71 COLOR 7 terminator at the last fixture 72 80 COLOR 8 2 On your Master unit access the main menu and press the UP or DOWN buttons so that Function is highlighted then 81 89 COLOR 9 press ENTER 90 98 COLOR 10 3 Select your desired operating mode Use the UP or DOWN but 99 107 COLOR 11 tons to select between Auto Program or Sound Control 108 116 COLOR 12 press ENTER to select your desired program 117 127 COLOR 13 4 Either Master or Alone will
3. 4 Carefully disconnect the two wires connected to the lamp Pic A 5 Next squeeze the lamp holding clips togther and lift the holder Pic B 6 Replace the lamp with an exact match Reassemble in reverse order PicA Pic B Fuse Replacement Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 64 3 Sixty 2R Cleaning Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp out put 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing Use a brush to wipe down the cooling vents and fan grill Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be
4. mode the fixture will operate as a single fixture The pro gram for this mode is selected in the Select program section of the control menu You can set the number of steps under Edit pro gram You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Auto Program is displayed and press ENTER 3 Either Master or Alone will be displayed 4 Press ENTER to to make your selection or press MODE ESC button to exit Sound Control With this function the internal program will run in sound active mode 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Sound Control is dis played press ENTER 3 Either Master or Alone will be displayed Use the UP or DOWN buttons to change the operating mode 4 Press ENTER to to make your selection or press MODE ESC button to exit ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 18 3 Sixty 2R System Menu INFORMATION Time Information Time information is always represented in hours Current Time This will allow you to check units current running time 1
5. www adj com 3 Sixty 2R Instruction Manual Page 34 3 Sixty 2R System Menu press ENTER 2 Press the UP or DOWN buttons until Reset Gobos is displayed 3 Press ENTER to reset or press MODE ESC to exit Reset Shutter With this function you can reset the shutter motor 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Shutter is displayed 3 Press ENTER to reset or press MODE ESC to exit Reset Others With this function you can reset all other motors 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Others is displayed 3 Press ENTER to reset or press MODE ESC to exit EFFECT ADJUST Test Channel With this function you can test correct each channel function 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Effect Adjust is highlighted then press ENTER 2 Press the UP or DOWN buttons until Test Channel is displayed press ENTER 3 Use the UP or DOWN buttons to scroll through the various chan nels 4 Press ENTER to select a channel to test or press MODE ESC to exit Manual Control With this function you can easily adjust the lamp ADJ Products LLC www ad
6. 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The 3 Sixty 2R can be controlled via DMX 512 protocol The 3 Sixty 2R can be either a 21 24 or 32 channel DMX unit The DMX address is set electronically using the controls on the front panel of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and Figur female XLR connector on either end of the cable Also M that ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 13 3 Sixty 2R Set Up DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Female Socket I 2 ey i Li J I I I I I I I I XLR Male Socket 1 Ground R 2 Cold Figure 3
7. 39 3 Sixty 2R Error Codes missing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB O5Er COLOR WHEEL error This message will appear after a fixture reset if the head s mag netic indexing circuit malfunctions sensor failed or magnet is missing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB O6Er FIXED GOBO WHEEL error This message will appear after a fixture reset if the magnetic indexing circuit malfunctions sensor failed or magnet is miss ing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 40 3 Sixty 2R Operation Universal DMX Control This function allows you to use a uni versal DMX 512 controller such as the Elatione DMX Operator or Elatione Show Designer to control head movement the color wheel gobo wheel prism master dimmer shutter strobe and vari ous other features A DMX controller allows you to create unique pro grams tailored to your individual needs 1 The 3 Sixty 2R has a 21 Channel mode 24 Channel mode and 32 Channel mode See pages 43 63 for detailed description of the DMX traits 2 To control your fixture in DMX mode follow the set up procedures on pages 13 15 as well as the set up specifications that are included with your DMX controller Use the
8. Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the prod uct only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and wil
9. Controls and Functions exposed this lamp emits strong UV radiation Please see page 7 for important information about the Philips Platinum 5R discharge lamp 13 Power Cord Inlet This cord is designed to match the electri cal requirements of the unit Voltage may vary from venue to venue when connecting this unit to a power supply be sure to connect to a matching power outlet Never use this fixture if the ground prong has been removed or broken off The ground prong is designed to reduce the risk of fire or electrical shock in the event the unit suffers from an internal short 14 Fuse Holder This housing stores a 7 amp protective fuse Never defeat the fuse the fuse is designed to protect the electronics in the event of severe power fluctuations Always be sure to replace the fuse with an exact match as the one being replaced unless otherwise told to do so by an authorized ADJ service technician 15 XLR Input Jack This jack is used to receive an incoming DMX signal or Master Slave signal 16 XLR Output Jack This jack is used to transmit the incoming DMX signal to another DMX fixture or transmit a Master Slave signal to the next 3 Sixty 2R in the chain For best results in DMX or Master Slave mode terminate this jack if it is the last unit in the chain See Line Termination on page 14 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 12 3 Sixty 2R Set Up Power Supply The ADJ 3 Sixty 2R con
10. Pin 3 Pin 3 Not Used Not Used Po Pin 4 Do Not Use Pin 5 Do Not Use ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 15 3 Sixty 2R System Menu Dmx Address A001 AXXX DMX address setting Dmx Value PAN DMX value display Z Slave Mode Slavel Slave2 Slave3 Slave setting 2 Auto Program Master Alone Auto program Sound Control Master Alone Music control Time Information Current Time XXXX Hours Power on running time Total Run Time XXXX Hours Fixture running time Last Run Time XXXX Hours Fixture Last times clear S Lamp Hours XXXX Hours Lamp running time Lamp Off Time XXXX Minute Lamp off time E LastRun Password Password XXX Timer Password 038 Clean Last Run ON OFE Clear Fixture Last time LampTime Password Password XXX Lamp Password 038 Clean Lamp Time ON OFE Clear lamp time Temperature Info Head Temperature XXX C F Temperature in the head Software Version _ V1 0 0 Software version Lamp On Off ON oFF Lamp on off Automatic On ON OFF Lamp on off Power on amp Lamp On via DMX ON OFF Lamp on via DMX amp Lamp Off via DMX ONoFF Lamp off via DMX 5 Max On at Temp 20 79 C 5G 68 174 F BH Lamp restart at temp Lamp Off Temp 80 139 C 130 176 282 F B0 Lamp off at temp Status Settings Address Via DMX ON OFF Add via DMX No DMX Status Close HOI Auto Music A
11. Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Current Time is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the current run ning time 5 Press ENTER or press MODE ESC to exit Total Run Time This will allow you to check units total running time 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Total Run Time is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the total run ning time 5 Press ENTER or press MODE ESC to exit Last Run Time This will allow you to check the last running time of the lamp 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 19 3 Sixty 2R System Menu 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Last Run Time is displayed
12. and press ENTER 4 XXXX will now be displayed XXXX represents the last running time 5 Press ENTER or press MODE ESC to exit Lamp Hours This will allow you to check the running time of the lamp 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Lamp Hours is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the lamp run ning time 5 Press ENTER or press MODE ESC to exit Lamp Off Time This will allow you to check the running time of the lamp the last time that the lamp was On 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Lamp Off Time is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the running time of the lamp the last time that the lamp was On ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 20 3 Sixty 2R System Menu 5 Press ENTER or press MODE ESC to exit Last Run Password This will display the timer password 1 Press the MODE ESC button to a
13. controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the directions on pages 36 37 to select your DMX Channel mode and follow the instruction on page 17 to set the DMX address 6 For longer cable runs more than a 100 feet use a terminator on the last fixture 7 For help operating in DMX mode consult the manual included with your DMX controller a aS Stand Alone Sound Active or Auto Program This mode allows a single unit to run to the beat of the music or run through a built in program AUTO PROGRAM 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Auto Program is dis played and press ENTER 3 Either Master or Alone will be displayed Using the UP or DOWN buttons select Alone and press ENTER SOUND ACTIVE 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Sound Control is dis played press ENTER 3 Either Master or Alone will be displayed Using the UP or ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 41 3 Sixty 2R Operation DOWN buttons select Alone and press ENTER 3 Sixty 2R 21 Channel DMX Mode Channel Value Function 0 255 PAN MOVEMENT 8bit 540 or 630
14. 96 197 203 204 210 211 217 GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE GOBO 8 SHAKE GOBO 9 SHAKE GOBO 10 SHAKE GOBO 11 SHAKE GOBO 12 SHAKE GOBO 13 SHAKE GOBO 14 SHAKE 155 161 162 168 169 175 176 182 183 189 190 196 197 203 204 210 211 217 218 255 GOBO 6 SHAKE GOBO 7 SHAKE GOBO 8 SHAKE GOBO 9 SHAKE GOBO 10 SHAKE GOBO 11 SHAKE GOBO 12 SHAKE GOBO 13 SHAKE GOBO 14 SHAKE GOBO WHEEL ROTATION SLOW FAST LEFT PRISM GOBO MACROS 218 255 GOBO WHEEL ROTATION SLOW FAST RIGHT GOBO WHEEL 0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63 64 71 72 79 80 87 88 95 96 103 104 111 112 119 120 126 127 193 134 140 144 447 148 154 OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12 GOBO 13 GOBO 14 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 52 12 LEFT PRISM ROTATION 0 127 PRISM INDEXING ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 53 8 FACET PRISM MACRO 1 MACRO 2 MACRO 3 MACRO 4 MACRO 5 MACRO 6 MACRO 7 MACRO 8 MACRO 9 MACRO 10 MACRO 11 MACRO 12 MACRO 13 MACRO 14 MACRO 15 MACRO 16 3 Sixty 2R 24 Channel DMX Mode 3 Sixty 2R 24 Channel DMX Mode Channel Value Function Channel Value Function 12 LEFT PRISM ROTATION 15 LEFT SHUTTER amp STROBE 128 189 FORWARD PRI
15. DOM STROBE SLOW FAST BLACKOUT BY MOVEMENT SHUTTER OPEN BLACKOUT BY WHEEL CHANGING 0 255 LEFT MASTER DIMMER 0 100 NO FUNCTION SHUTTER OPEN POSITION PULSE EFFECT IN SEQUENCES LAMP ON SHUTTER OPEN LAMP OFF RANDOM STROBE SLOW FAST ALL MOTOR RESET SHUTTER OPEN SCAN MOTOR RESET 0 255 RIGHT MASTER DIMMER 0 100 COLOR MOTOR RESET 16 TILT LOCALIZATION MODEL SELECT GOBO MOTOR RESET 0 79 WO TILTS MOVEMENT SEPERATELY SHUTTER DIMMER MOTOR RESET 14 RIGHT SHUTTER amp STROBE LAMP ON OFF RESET amp PROGRAMS SHUTTER CLOSED COLOR CHANGE NORMAL SHUTTER OPEN COLOR CHANGE TO ANY POSITION STROBING SLOW FAST COLOR amp GOBO CHANGE TO ANY 80 159 TWO TILTS WHOLE MOVEMENT OTHER MOTOR RESET 160 255 NO FUNCTION INTERNAL PROGRAM 1 17 PAN CONTINUOUS ROTATION INTERNAL PROGRAM 2 NO FUNCTION INTERNAL PROGRAM 3 128 189 FORWARDS ROTATION FAST SLOW INTERNAL PROGRAM 4 NO FUNCTION INTERNAL PROGRAM 5 194 255 BACKWARDS ROTATION SLOW FAST INTERNAL PROGRAM 6 18 LEFT TILT CONTINUOUS ROTATION INTERNAL PROGRAM 7 NO FUNCTION SOUND ACTIVE PROGRAM FORWARDS ROTATION FAST SLOW The pan degree can be changed between 540 and 630 See NO FUNCTION page 28 to change the pan degree 194 255 IBACKWARDS ROTATION SLOW FAST RIGHT TILT CONTINUOUS ROTATION NO FUNCTION 128 189 FORWARDS ROTATION FAST SLOW ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 48 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manua
16. E MOVEMENT 2 80 159 160 255 NO FUNCTION ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 61 190 193 194 255 3 Sixty 2R 0 127 128 189 190 193 194 255 0 127 128 189 190 193 194 255 0 127 128 189 190 193 194 255 0 225 226 235 236 245 246 255 0 19 20 29 30 39 40 59 60 79 80 84 85 87 88 90 91 93 94 96 97 99 100 119 32 Channel DMX Mode Channel Value Function PAN CONTINUOUS ROTATION NO FUNCTION FORWARDS ROTATION FAST SLOW NO FUNCTION BACKWARDS ROTATION SLOW FAST LEFT TILT CONTINUOUS ROTATION NO FUNCTION FORWARDS ROTATION FAST SLOW NO FUNCTION BACKWARDS ROTATION SLOW FAST RIGHT TILT CONTINUOUS ROTATION NO FUNCTION FORWARDS ROTATION FAST SLOW NO FUNCTION BACKWARDS ROTATION SLOW FAST PAN TILT MOVEMENT SPEED MAX TO MIN SPEED BLACKOUT BY MOVEMENT BLACKOUT BY WHEEL CHANGING NO FUNCTION LAMP ON OFF RESET amp PROGRAMS COLOR CHANGE NORMAL COLOR CHANGE TO ANY POSITION COLOR amp GOBO CHANGE TO ANY POSITION LAMP ON LAMP OFF ALL MOTOR RESET SCAN MOTOR RESET COLOR MOTOR RESET GOBO MOTOR RESET SHUTTER DIMMER MOTOR RESET OTHER MOTOR RESET INTERNAL PROGRAM 1 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 62 3 Sixty 2R 32 Channel DMX Mode Channel Value Function LAMP ON OFF RESET amp PROGRAMS INTERNAL PROGRAM 2 INTERNAL PROGRAM 3 INTERNAL PROGRAM 4 INTERNAL PROGRAM 5 I
17. ESC to exit NOTE When the temperature around the lamp is higher then the preset value for longer then 5 mins the unit will automatically shut Off the lamp If the lamp is automatically shut off due to over heat it can not be restriked automatically it must be turned On again manually PERSONALITY Status Settings ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 25 3 Sixty 2R Address via DMX With this function you can adjust the DMX address via external controller 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until Address via DMX is dis played and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between System Menu 5 Press ENTER to confirm your selection or press MODE ESC to exit To use this function follow these instructions To adjust the address of your unit you must first go to the address that it is currently set to From there you can adjust the address First make sure all channels are set to the value of 0 1 On your DMX controller set the DMX value of Channel 1 to the value 7 2 Now set the DMX value of Channel 2 to the value 7 to adjust the starting address between 1 and 255 To adjust t
18. GOBO WHEEL ROTATION 32 79 FROST SLOW FAST 80 127 8 FACET PRISM 0 255 RIGHT FIXED GOBO FINE INDEXING 128 135 MACRO 1 15 LEFT PRISM GOBO MACROS 136 143 MACRO 2 0 31 OPEN 144 151 MACRO 3 32 79 FROST 152 159 MACRO 4 80 127 8 FACET PRISM 160 167 MACRO 5 128 135 MACRO 1 168 175 MACRO 6 136 143 MACRO 2 176 183 MACRO 7 144 151 MACRO 3 184 191 MACRO 8 152 159 MACRO 4 192 199 MACRO 9 160 167 MACRO 5 200 207 MACRO 10 168 175 MACRO 6 208 215 MACRO 11 176 183 MACRO 7 216 223 MACRO 12 184 191 MACRO 8 224 231 MACRO 13 192 199 MACRO 9 232 239 MACRO 14 200 207 MACRO 10 240 247 MACRO 15 208 215 MACRO 11 248 255 MACRO 16 216 223 MACRO 12 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 59 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 60 3 Sixty 2R 32 Channel DMX Mode Channel Value Function 19 RIGHT PRISM ROTATION 0 127 PRISM INDEXING 128 189 FORWARD PRISM ROTATION FAST SLOW NO ROTATION BACKWARD PRISM ROTATION SLOW FAST 21 LEFT SHUTTER amp STROBE SHUTTER CLOSED SHUTTER OPEN STROBING SLOW FAST SHUTTER OPEN PULSE EFFECT IN SEQUENCES SHUTTER OPEN RANDOM STROBE SLOW FAST SHUTTER OPEN 7 RIGHT SHUTTER amp STROBE SHUTTER CLOSED SHUTTER OPEN STROBING SLOW FAST SHUTTER OPEN PULSE EFFECT IN SEQUENCES SHUTTER OPEN RANDOM STROBE SLOW FAST SHUTTER OPEN 0 255 RIGHT FINE DIMMER INTENSITY TWO TILTS WHOL
19. INE 0 255 COLOR WHEEL CHANGE FINE LEFT GOBO WHEEL ADJ Products LLC a is 16 23 24 31 32 39 40 47 48 55 56 63 64 71 72 79 80 87 88 95 96 103 104 111 112 119 OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12 GOBO 13 GOBO 14 www adj com 3 Sixty 2R Instruction Manual Page 58 ADJ Products LLC 0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63 64 71 2379 80 87 88 95 96 103 104 111 112 119 OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12 GOBO 13 GOBO 14 www adj com 3 Sixty 2R Instruction Manual Page 59 3 Sixty 2R 32 Channel DMX Mode 3 Sixty 2R 32 Channel DMX Mode Channel Value Function Channel Value Function 13 RIGHT GOBO WHEEL LEFT PRISM GOBO MACROS 120 126 GOBO 1 SHAKE 224 231 MACRO 13 127 133 GOBO 2 SHAKE 232 gt 239 MACRO 14 134 140 GOBO 3 SHAKE 240 247 MACRO 15 141 147 GOBO 4 SHAKE 248 255 MACRO 16 148 154 GOBO 5 SHAKE LEFT PRISM ROTATION 155 161 GOBO 6 SHAKE 0 127 PRISM INDEXING 162 168 GOBO 7 SHAKE 128 189 FORWARD PRISM ROTATION 169 175 GOBO 8 SHAKE FAST SLOW 176 182 GOBO 9 SHAKE 190 193 NO ROTATION 183 189 GOBO 10 SHAKE 194 255 BACKWARD PRISM ROTATION 190 196 GOBO 11 SHAKE SLOW FAST 197 203 GOBO 12 SHAKE 204 210 GOBO 13 SHAKE RIGHT PRISM GOBO MACROS 211 217 GOBO 14 SHAKE OPEN 218 255
20. L PROGRAM 2 INTERNAL PROGRAM 3 INTERNAL PROGRAM 4 INTERNAL PROGRAM 5 INTERNAL PROGRAM 6 220 239 INTERNAL PROGRAM 7 240 255 SOUND ACTIVE PROGRAM The pan degree can be changed between 540 and 630 See page 28 to change the pan degree 0 19 20 29 30 39 40 59 60 79 80 84 85 87 88 90 91 93 94 96 97 99 100 119 120 139 140 159 160 179 180 199 200 219 190 193 194 255 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 56 3 Sixty 2R 32 Channel DMX Mode Channel Value Function LEFT GOBO WHEEL 3 Sixty 2R 32 Channel DMX Mode Channel Value Function RIGHT COLOR WHEEL 36 44 45 53 54 62 63 71 72 80 81 89 90 98 99 107 108 116 117 127 128 189 190 193 194 255 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 COLOR 9 COLOR 10 COLOR 11 COLOR 12 COLOR 13 FORWARD RAINBOW EFFECT FAST SLOW NO ROTATION BACKWARDS RAINBOW EFFECT 120 126 127 133 134 140 141 147 148 154 155 161 162 168 169 175 176 182 183 189 190 196 197 203 204 210 211 217 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE GOBO 8 SHAKE GOBO 9 SHAKE GOBO 10 SHAKE GOBO 11 SHAKE GOBO 12 SHAKE GOBO 13 SHAKE GOBO 14 SHAKE GOBO WHEEL ROTATION SLOW FAST 0 255 LEFT FIXED GOBO FINE INDEXING RIGHT GOBO WHEEL SLOW FAST 218 255 RIGHT COLOR WHEEL F
21. LC www adj com 3 Sixty 2R Instruction Manual Page 54 3 Sixty 2R Channel Value 0 127 128 189 190 193 194 255 0 225 226 235 236 245 246 255 24 Channel DMX Mode Function RIGHT TILT CONTINUOUS ROTATION NO FUNCTION FORWARDS ROTATION FAST SLOW NO FUNCTION BACKWARDS ROTATION SLOW FAST PAN TILT MOVEMENT SPEED MAX TO MIN SPEED BLACKOUT BY MOVEMENT BLACKOUT BY WHEEL CHANGING NO FUNCTION 3 em 2R 0 255 PAN MOVEMENT 8bit 540 or 630 0 255 PAN FINE 16bit LEFT TILT MOVEMENT 8bit LEFT TILT FINE 16bit RIGHT TILT MOVEMENT 8bit a 0 255 RIGHT TILT FINE 16bit LEFT COLOR WHEEL Value 9 17 32 Channel DMX Mode Function OPEN COLOR 1 18 26 27 35 36 44 45 53 54 62 63 71 72 80 81 89 90 98 99 107 108 116 117 127 128 189 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 COLOR 9 COLOR 10 COLOR 11 COLOR 12 COLOR 13 FORWARD RAINBOW EFFECT FAST SLOW NO ROTATION BACKWARDS RAINBOW EFFECT SLOW FAST t 0 255 COLOR WHEEL CHANGE FINE RIGHT COLOR WHEEL OPEN COLOR 1 COLOR 2 COLOR 3 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 57 LAMP ON OFF RESET amp PROGRAMS COLOR CHANGE NORMAL COLOR CHANGE TO ANY POSITION COLOR amp GOBO CHANGE TO ANY POSITION LAMP ON LAMP OFF ALL MOTOR RESET SCAN MOTOR RESET COLOR MOTOR RESET GOBO MOTOR RESET SHUTTER DIMMER MOTOR RESET OTHER MOTOR RESET INTERNAL PROGRAM 1 INTERNA
22. N 218 255 GOBO WHEEL ROTATION 194 255 BACKWARDS RAINBOW EFFECT SLOW FAST SLOW FAST RIGHT GOBO WHEEL 0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63 64 71 72 79 80 87 88 95 96 103 104 111 112 119 120 126 127 133 134 140 141 147 148 154 155 161 162 168 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 44 LEFT GOBO WHEEL OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12 GOBO 13 GOBO 14 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE 0 7 8 15 16 23 24 31 32 39 40 47 48 55 56 63 64 71 72 79 80 87 88 95 96 103 104 111 1224119 120 126 127 133 134 140 141 147 148 154 155 161 162 168 169 175 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 45 OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12 GOBO 13 GOBO 14 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE GOBO 8 SHAKE 3 Sixty 2R 21 Channel DMX Mode 3 Sixty 2R 21 Channel DMX Mode Channel Value Function Channel Value Function 7 RIGHT GOBO WHEEL LEFT PRISM ROTATION 194 255 BACKWARD PRISM ROTATION SLOW FAST 176 182 GOBO 9 SHAKE 183 189 GOBO 10 SHAKE 190 196 GOBO 11 SHAKE RIGHT PRISM GOBO MACROS 197 203 GOBO 12 SHAKE
23. N buttons until Lamp Time Password is dis played and press ENTER 4 The Lamp Time Password is 038 5 Press ENTER or press MODE ESC to exit Clean Lamp Time This will allow you to clear the lamp time run ning time Please clear the lamp running time every time you replace the lamp You need to put in the Lamp Time Password before doing this Please see the section before this 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Clear Lamp Time is dis played and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Temperature Info This will allow you to check the moving head temperature 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Temperature Info is dis played press ENTER 3 Head Temperature will now be displayed press ENTER 4 XXX will now be displayed XXX represents the current tem perature of the moving head ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 22 3 Sixt
24. N buttons to adjust the DMX address 4 Press ENTER to confirm or press MODE ESC to return to the main menu DMX Value This function will allow you to see the DMX value of each DMX channel that is currently being used at the time 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until DMX Value is displayed and press ENTER 3 A DMX Channel will be displayed Example Prism Color Wheel Gobo Wheel etc Press ENTER when you find the DMX channel that you would like to check When you press ENTER the DMX value of that channel will displayed 4 Press the MODE ESC button to exit Slave Mode This function lets you designate the unit as the slave in a Master Slave configuration ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 17 3 Sixty 2R System Menu 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Slave Mode is displayed and press ENTER 3 Either Slave 1 Slave 2 or Slave 3 will be displayed Press ENTER to select either of the three or press MODE ESC button to exit Auto Program This function allows the internal programs to run in either stand alone or master slave mode In Master mode the fix ture will send DMX data to other fixtures connect via the DMX chain In Alone
25. NTER 3 Press UP or DOWN buttons until Display Shutoff Time is dis played and press ENTER 4 05m 5 minutes will be displayed use the UP and DOWN but tons to adjust the shutoff time between 02m 60m or Off 5 Press ENTER to confirm your selection or press MODE ESC to exit Display Reverse With this function you can rotate flip the display 180 degrees 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Display Setting is dis played press ENTER 3 Press UP or DOWN buttons until Display Reverse is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Key Lock With this function activated the buttons will lock autom matically after 15 seconds 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Display Setting is dis played press ENTER 3 Press UP or DOWN buttons until Key Lock is displayed and press ENTER ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 32 3 Sixty 2R System Menu 4 Either Off or On will be displayed use the UP
26. NTERNAL PROGRAM 6 220 239 INTERNAL PROGRAM 7 240 255 SOUND ACTIVE PROGRAM The pan degree can be changed between 540 and 630 See page 28 to change the pan degree 120 139 140 159 160 179 180 199 200 219 3 Sixty 2R Photometric Chart Intensity LUX 50460 21850 12710 2 Beam opening m 20 Distance m 01 24 Diameter m 60 62 0 93 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 63 3 Sixty 2R Lamp Replacement Caution Always replace with the exact same type lamp and fuse unless otherwise specified by an authorized ADJ service technician Replacing with anything other than the specified part can damage your unit and will void your manufactures warranty Warning If you continue to blow lamps or fuses STOP using the unit Contact customer support for further instructions you may have to return the unit for servicing Continuing to use the unit may cause serious damage Lamp Replacement Caution Never attempt to change the lamp while the fixture is plugged in Always disconnect the main power and allow the unit ample time to cool before attempting to replace the lamp Please see page 7 for important information regarding the discharge lamp 1 Be sure to follow the proper handling procedures that deal with discharge lamps 2 Remove the four small screws labeled A B C amp D on the rear of the moving head 3 After removing the screws gently remove the panel
27. OPEN 204 210 GOBO 13 SHAKE FROST 211 217 GOBO 14 SHAKE 8 FACET PRISM 218 255 GOBO WHEEL ROTATION MACRO 1 SLOW FAST MACRO 2 LEFT PRISM GOBO MACROS MACRO 3 0 31 OPEN MACRO 4 32 79 FROST MACRO 5 80 127 8 FACET PRISM MACRO 6 128 135 136 143 144 151 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 216 223 224 231 232 239 MACRO 1 MACRO 2 MACRO 3 MACRO 4 MACRO 5 MACRO 6 MACRO 7 MACRO 8 MACRO 9 MACRO 10 MACRO 11 MACRO 12 MACRO 13 MACRO 14 248 255 0 127 128 189 MACRO 7 MACRO 8 MACRO 9 MACRO 10 MACRO 11 MACRO 12 MACRO 13 MACRO 14 MACRO 15 MACRO 16 RIGHT PRISM ROTATION PRISM INDEXING FORWARD PRISM ROTATION FAST SLOW NO ROTATION BACKWARD PRISM ROTATION SLOW FAST LEFT SHUTTER amp STROBE SHUTTER CLOSED SHUTTER OPEN STROBING SLOW FAST ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 47 240 247 MACRO 15 190 193 248 255 MACRO 16 194 255 LEFT PRISM ROTATION 0 127 PRISM INDEXING 128 189 FORWARD PRISM ROTATION FAST SLOW 190 193 NO ROTATION ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 46 3 Sixty 2R 21 Channel DMX Mode 3 Sixty 2R 21 Channel DMX Mode Function Channel Value Function 12 LEFT SHUTTER amp STROBE NO FUNCTION SHUTTER OPEN 94 255 BACKWARDS ROTATION SLOW FAST PULSE EFFECT IN SEQUENCES 20 PAN TILT MOVEMENT SPEED SHUTTER OPEN MAX TO MIN SPEED RAN
28. Rev 3 14 User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use T
29. SM ROTATION SHUTTER CLOSED FAST SLOW SHUTTER OPEN 190 193 NO ROTATION STROBING SLOW FAST 194 255 BACKWARD PRISM ROTATION SHUTTER OPEN SLOW FAST PULSE EFFECT IN SEQUENCES RIGHT PRISM GOBO MACROS SHUTTER OPEN 0 31 OPEN RANDOM STROBE SLOW FAST 32 79 FROST SHUTTER OPEN 80 127 8 FACET PRISM 128 135 MACRO 1 RIGHT SHUTTER amp STROBE 136 143 MACRO 2 SHUTTER CLOSED 144 151 MACRO 3 SHUTTER OPEN STROBING SLOW FAST 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 216 223 224 231 232 239 240 247 248 255 MACRO 4 MACRO 5 MACRO 6 MACRO 7 MACRO 8 MACRO 9 MACRO 10 MACRO 11 MACRO 12 MACRO 13 MACRO 14 MACRO 15 MACRO 16 80 159 160 255 SHUTTER OPEN PULSE EFFECT IN SEQUENCES SHUTTER OPEN RANDOM STROBE SLOW FAST SHUTTER OPEN 0 255 RIGHT MASTER DIMMER 0 100 TILT LOCALIZATION MODEL SELECT TWO TILTS WHOLE MOVEMENT NO FUNCTION PAN CONTINUOUS ROTATION NO FUNCTION 128 189 FORWARDS ROTATION FAST SLOW NO FUNCTION 194 255 IBACKWARDS ROTATION SLOW FAST 21 LEFT TILT CONTINUOUS ROTATION NO FUNCTION 128 189 FORWARDS ROTATION FAST SLOW RIGHT PRISM ROTATION 0 127 PRISM INDEXING 128 189 FORWARD PRISM ROTATION FAST SLOW 190 193 NO ROTATION 194 255 BACKWARD PRISM ROTATION SLOW FAST NO FUNCTION 194 255 BACKWARDS ROTATION SLOW FAST ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 55 ADJ Products L
30. TER 3 Use the UP or DOWN buttons to scroll through the 3 DMX Channel Modes ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 36 3 Sixty 2R System Menu Standard Mode This is 24 Channel Mode Basic Mode This is 21 Channel Mode Extended Mode This is 32 Channel Mode User Mode A B C These are customizable DMX modes Select either of these modes and set the amount of DMX Channels and what each channel does 4 Press the MODE ESC button once to return to the User Mode Set menu Edit User Mode This function allows the user to make the actual changes to the DMX channels 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that User Mode Set is highlighted then press ENTER 2 Press the UP or DOWN buttons until Edit User Mode is dis played press ENTER 3 Use the UP or DOWN buttons to find the User Mode you would like to edit and press ENTER 4 Use the UP and DOWN buttons to find the trait you would like to edit and press ENTER Use the UP and DOWN buttons to change the trait to your desired Channel number EDIT PROGRAM The fixture comes equipped with a built in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board Programs can be created and stored using the fixture s control board or by using an external DMX controller Select Program This function allows the user to select
31. and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Temperature C F With this function you can change the tempera ture display to show either Celsius or Fahrenheit 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press UP or DOWN buttons until Temperature C F is dis played and press ENTER 3 Either Celsius or Fahrenheit will be displayed use the UP and DOWN buttons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit Initial Status In this menu you are able to check the initial effect position 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Initial Status is displayed press ENTER 3 XXX will be displayed XXX represents the current effect posi tion 4 Press ENTER or press MODE ESC to exit Reset Default This will reset the unit to all default settings 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Default is displayed press ENTER ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 33 3 Si
32. anty 1 Year 365 days Auto Sensing Voltage This fixture contains a electronic bal last which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 69 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On HOM facebook com americandj twitter com americandj youtube com adjlighting
33. be displayed Using the UP or 128 189 FORWARD RAINBOW EFFECT DOWN buttons select Master and press ENTER FAST SLOW 5 For your Slave units access the main menu and press the UP 190 193 NO ROTATION or DOWN buttons so that Function is highlighted then press ENTER 6 Press the UP or DOWN buttons until Slave Mode is displayed and press ENTER 194 255 BACKWARDS RAINBOW EFFECT SLOW FAST RIGHT COLOR WHEEL Either Slave 1 Slave 2 or Slave 3 will be displayed Select your desired Slave setting and press ENTER Press MODE ESC if you want to return to the main menu You may change the show or invert the pan and tilt functions in the system menu by following the directions on pages 27 28 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 42 OPEN COLOR 1 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 43 3 Sixty 2R 21 Channel DMX Mode 3 Sixty 2R 21 Channel DMX Mode Channel Value Function Channel Value Function RIGHT COLOR WHEEL LEFT GOBO WHEEL 81 89 90 98 99 107 108 116 117 127 128 189 COLOR 9 COLOR 10 COLOR 11 COLOR 12 COLOR 13 FORWARD RAINBOW EFFECT FAST SLOW 169 175 176 182 183 189 190 196 197 203 204 210 211 217 GOBO 8 SHAKE GOBO 9 SHAKE GOBO 10 SHAKE GOBO 11 SHAKE GOBO 12 SHAKE GOBO 13 SHAKE GOBO 14 SHAKE 190 193 NO ROTATIO
34. be displayed use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Pan Reverse With this function you can reverse the Pan movement 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER This function is used with DMX mode 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until Pan Reverse is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Tilt_L Reverse With this function you can reverse the left head Tilt movement This function is used with DMX mode ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 27 3 Sixty 2R System Menu 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until Tilt_L Reverse is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Tilt_R Reverse With t
35. ccess the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Last Run Password is dis played and press ENTER 4 The Last Run Password is 038 5 Press ENTER or press MODE ESC to exit Clean Last Run This will allow you to clear the last run time of the unit You need to put in the Last Run Password before doing this Please see the section before this 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Clean Last Run is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Lamp Time Password This will display the lamp timer password 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 21 3 Sixty 2R System Menu 3 Press UP or DOW
36. channel 3 all at the same time you will see the error message flash 01Er and OSEr repeated 5 times If an error does occur during the initial start up procedure the fixture will self generate a second reset signal and try to realign all the motors and correct the errors if the errors persist after a second attempt a third attempt will be made If after a third attempt all the errors have not been corrected the fixture will make the following determinations 1 3 or more errors The fixture cannot function properly with three or more errors therefore the fixture will place itself in a stand by mode until subsequent repairs can be made 2 Less than 3 errors If the fixture has less than 3 errors there fore most other functions will work properly The fixture will attempt to operate normally until the errors can be corrected by a technician The errors in question will remain flashing in the display as a reminder of internal errors 01Er PAN movement error This message will appear after a fixture reset if the pan yoke s magnetic indexing circuit malfunctions Sensor failed or magnet is missing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB O3Er TILT movement error This message will appear after a fixture reset if the tilt mag netic indexing circuit malfunctions sensor failed or magnet is ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page
37. dis played press ENTER 3 Press UP or DOWN buttons until Password is displayed and press ENTER 4 The Password is 050 5 Press ENTER or press MODE ESC to exit RDM PID RDM stands for Remote Device Management This feature lets you control every aspect of your fixture remotely from an RDM controller Manual settings like adjusting the DMX address are no longer needed This is especially useful when the unit is installed in a remote area In this submenu you can see the units RDM ID number and adjust it as well 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Service Setting is dis played press ENTER 3 Press UP or DOWN buttons until RDM PID is displayed and press ENTER 4 XXXXXX will be displayed XXXXXX represents the units current RDM ID 5 Press ENTER or press MODE ESC to exit Display Setting Shutoff Time With this function you can have the LCD display after 2 60 minutes Use this function to adjust the time 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 31 3 Sixty 2R System Menu ENTER 2 Press the UP or DOWN buttons until Display Setting is dis played press E
38. e the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life Mounting 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the 3 Sixty 2R Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety cable through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 9 3 Sixty 2R Controls and Functions FRONT REAR ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 10 3 Sixty 2R Controls and Functions 1 Lens Assembly A high quality lens 2 Microphone This microphone receives external low frequencies to trigger the unit in Sound Active mode This microphone is designed to receive low frequency sounds only tapping on the microphone and high pitch sounds may not trigger the unit 3 DC Switch This button will allow you access to the system menu without have the need to actually plug in the unit Press this button for at least 3 seconds and the display will turn on and allow you t
39. hank you Table of Contents UC IMG cccrcatseaau anes ennast niher ieena a nai nne kans IMtrodUCtiON aiiis iranan aanak AEE EEA EEEE RiR EE aa Customer SUD DOM ss ciseacsaascicecnachaadtessnosvessbaxssacndesstacseaceecceactbes Safety PreCautiOns cccccccccccceceeeeeeeeeseeeeeeeesseseesessneeeeeaaees Feature Saenden nie Einin a ee i aaae Handling PRECAUTION Sis vncncadcnc cansasasaivensacsatepconoganemasatendidaatances Pre ONS ha MON asacharsivenenamusiteesiysssieiecdmancenacnens inten tegienente Important Discharge Lamp WarningS sseseeeeeeeees DOIN Gessie a E Ea a EE Controls and FunctionS sssseeeeeeeereeeeeeeeeeerrrrrrrrrrnrrnnrnnnnne DMX SD iescecat cate ccsatieoseade bacebaadtes ave eecebwasbauadscnestececmuceadeess System WOM csssdverctheonmesceaansennadebensiposesnszesnasnbiedanbocmuctonsnecsses Error COGS oa sinisccnsctnsiinesenasesdeanseasnidanisasvadocsnbewsanostsastedeastbontenns Operaatio 9 amare ee eee an na eer EE EEOAE EE OMX lraitS starina a hiaan A EEE oS ERENER Photometric CMAN ciscccccsacacanannsdsivisnsasdstpnetnmondcteaneadhaexannnanenes Lamp Replacement ccsseeeeeeeeeeeeeeeeaaeeaasseeeeseeeeeeeeaes Fuse Replacement sccesseeeeeeceeeeeeeeeeaeeaasseeeeseeeeeeeeees OF ANI Ys asscn 25 a accanebuseceeassesnduattem censusveessbecendebdonsteds wasigeratseears Trouble SIO OWING ae cincsnintscssianssindenaniediesssensedenonsiesahennnanvanazaneces VANE Y icc
40. he address between 256 and 511 set Channel 2 to the value 8 3 Set the DMX value of Channel 3 to your desired start ing address This will take about 20 seconds before the unit accepts the new DMX address EXAMPLE f you want the address to be 57 you must first set the address that is currently assingned to the unit Then set Channel 1 s value to 7 Channel 2 s value to 7 and Chan nel 3 s value to 57 Wait 20 seconds and the address should change on the unit to 57 2ND EXAMPLE lf you want the address to be 420 you must first set the address that is currently assingned to the unit If ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 26 3 Sixty 2R System Menu you want the set the address to 420 set Channel 1 s value to 7 Channel 2 s value to 8 and Channel 3 s to 164 256 164 420 No DMX status With this function if the DMX signal is suddenly lost the unit will automatically go into 1 of 3 modes 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until No DMX Status is displayed and press ENTER 4 Either Hold Last DMX setting Close Blackout Music Sound Active or Auto Auto Program will
41. his function you can reverse the right head Tilt movement This function is used with DMX mode 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until Tilt_R Reverse is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Pan Degree With this function you can change the pan degree from 630 to 540 This function is used with DMX mode 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 28 3 Sixty 2R System Menu 3 Press UP or DOWN buttons until Pan Degree is displayed and press ENTER 4 Either 540 or 630 will be displayed use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Feedback With this function you can feedback switch the pan movement or tilt movement 1 Press the MODE ESC button to access the main menu Press the UP or DOWN bu
42. if you wish to activate this func tion or Off to deactivate 4 Press ENTER to confirm your selection or press MODE ESC to exit ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 24 3 Sixty 2R System Menu Max on at temp With this function you can set the inside tempera ture from which the lamp will restrike after automatic shut off 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Max On at Temp is dis played press ENTER 3 113 F or 45 C should now be displayed 113 F represents the temperature that the lamp will restrike at The temperature that is recommended is 113 F 4 Press ENTER to confirm your selection or press MODE ESC to exit Lamp off temp With this function you can set the inside tempera ture at which point the lamp will shut off 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Max On at Temp is dis played press ENTER 3 266 F or 130 C should now be displayed 266 F or 130 C represents the temperature that the lamp will automatically switch off at The temperature that is recommended is 266 F 4 Press ENTER to confirm your selection or press MODE
43. ixty 2R Features Micro Stepping Motors for Smooth Color and Gobo Transitions 3 Modes of DMX 512 Protocol Compatible 21 DMX Channel Mode 24 DMX Channel Mode and 32 DMX Channel Mode Independent Gobo and Color Wheels 14 Gobos Spot 13 Colors White RDMxX Lets you set the DMX address from any DMX Controller 3 Operating Modes Auto Run Sound Active amp DMX Controlled Stand Alone Setup or Master Slave Configuration Internal Microphone Philips MSD Platinum 2R Discharge Edit and Save Scenes into the Memory 360 Pan amp Tilt Rotation Digital Display for Address and Function Setting ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 5 3 Sixty 2R General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regard ing the use and maintenance of this unit Please keep this manual with the unit for future reference 3 Sixty 2R Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use ADJ Products LLC will not accept any liabili
44. j com 3 Sixty 2R Instruction Manual Page 35 3 Sixty 2R System Menu All effects will be canceled the shutter will open and output intensity will be 100 With the individual functions you can focus the light on flat surface a wall and finely adjust the lamp 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Effect Adjust is highlighted then press ENTER 2 Press the UP or DOWN buttons until Manual Control is dis played press ENTER 3 Use the UP or DOWN buttons to scroll through the various func tions 4 Press ENTER when you find the function you would like to adjust or press MODE ESC to exit Calibration With this function you can calibrate and adjust the effects wheels to their correct positions The Calibration password 050 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Effect Adjust is highlighted then press ENTER 2 Press the UP or DOWN buttons until Calibration is displayed press ENTER 3 XXXX will be displayed The password is 050 4 Press ENTER to confirm or press MODE ESC to exit USER MODE SET User Mode This mode will let you select your desired DMX Channel mode 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that User Mode Set is highlighted then press ENTER 2 Press the UP or DOWN buttons until User Mode is displayed press EN
45. l Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until Mic Sensitivity is displayed and press ENTER 4 70 will be displayed use the UP and DOWN buttons to adjust the sensitivity between 0 99 5 Press ENTER to confirm your selection or press MODE ESC to exit Hibernation With this function the lamp and step motors will power off if there is no DMX signal within 15 mins factory defualt Once it receives a DMX signal the fixture will reset itself 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Hibernation is displayed and press ENTER 4 15M will be displayed use the UP and DOWN buttons to adjust the hibernation period between 01M 99M or Off 5 Press ENTER to confirm your selection or press MODE ESC to exit Service Setting Password With this function you can enter the RDM password so ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 30 3 Sixty 2R System Menu that you can access and change the RDM ID number 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Service Setting is
46. l Page 49 3 emt 2R 24 Channel DMX Mode 3 Sixty 2R 24 Channel DMX Mode Value Function Channel Value Function 4 0 255 PAN MOVEMENT 8bit 540 or 630 RIGHT COLOR WHEEL ee ee a ee 54 62 COLOR 6 3 LEFT TILT MOVEMENT 8bit 63 71 COLOR 7 255 LEFT TILT FINE 16bit ie an cet aa ee a 0 8 colon 1o 99 107 COLOR 11 LEFT COLOR WHEEL 108 116 COLOR 12 0 8 OPEN 117 127 COLOR 13 9 17 COLOR 1 128 189 FORWARD RAINBOW EFFECT 18 26 COLOR 2 FAST SLOW 27 35 COLOR 3 190 193 NO ROTATION 36 44 COLOR 4 194 255 BACKWARDS RAINBOW EFFECT 45 53 COLOR 5 SLOW FAST 54 62 COLOR 6 LEFT GOBO WHEEL 63 71 72 80 81 89 90 98 99 107 108 116 117 127 COLOR 7 COLOR 8 COLOR 9 COLOR 10 COLOR 11 COLOR 12 COLOR 13 OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 128 189 FORWARD RAINBOW EFFECT 3 GOBO 7 FAST SLOW GOBO 8 190 193 NO ROTATION GOBO 9 194 255 BACKWARDS RAINBOW EFFECT P GOBO 10 GOBO 11 RIGHT COLOR WHEEL 5 GOBO 12 GOBO 13 GOBO 14 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE COLOR 5 GOBO 4 SHAKE ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 50 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 51 3 Sixty 2R 24 Channel DMX Mode Channel Value Function 10 RIGHT GOBO WHEEL 3 Sixty 2R 24 Channel DMX Mode Channel Value Function LEFT GOBO WHEEL 148 154 165 161 162 168 169 175 176 182 183 189 190 1
47. l absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only writ
48. nd appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Mounting Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself These installaiton should be checked by a skilled person once a year iano i K ZSA SA SSS A A PE W SZ Sa The 3 Sixty 2R is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface To avoid internal damage to the unit never mount the unit on its side as illustrated above Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails see next page Never use the carrying handles for secondary attachment ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 8 3 Sixty 2R NOTICE The suitable enviromental temperature for this light ing fixture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or abov
49. o make changes to the system menu 4 Digital Display This display shows the menu and operating func tions that you can choose from 5 Left Button This button is used to move to the left when navigat ing through the system menu 6 Down Button This button is used to scroll backwards when navi gating through the system menu 7 Enter Button This button is used to select and confirm a function in the system menu and enter the submenus 8 Right Button This button is used to move to the right when navi gating through the system menu 9 Mode Esc Button This button is used to enter the main menu and exit the submenus 10 Up Button This button is used to scroll forwards when navigating through the system menu 11 Carrying Handles The includes built in carrying handles Be sure to always handle the unit by the built in handles Never lift or car rying the unit by head or yoke Pulling on or transporting the unit by the moving head may severely damage the unit and will void the unit warranty 12 Lamp Assembly and Access Plate This plate accesses the lamp socket assembly The unit includes a spring mounted discharge lamp Be sure to only replace with same type lamp After replacing a lamp be sure the lamp is centered in the reflector See pages 64 for details installing replacement lamps Never operate this unit with the lamp ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 11 3 Sixty 2R
50. ogram 1 10 Pogama run Auto Pro Part 3 Program 1 10 POgAMS g Edit Program Program 1 Program Test Testing program 5 Step 01 SCxxx Program in loop Program 10 Step 64 SCxxx Save and exit Edit Scenes Edit Scene 001 Pan Tilt A E ge Save and automatically Edit Scene Fade Time 250 Secne Time zen N manual scenes edit Input By Exterior Rec Controller XX XX Automat scenes rec ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 16 3 Sixty 2R System Menu The main menu is accessed by pressing the MODE ESC button Browse through the menu by using the UP DOWN RIGHT amp LEFT buttons Press the ENTER button to access the desired menu You can scroll through the submenus using the UP DOWN RIGHT amp LEFT buttons To confirm every selection press the ENTER button You can exit every menu and submenu by pressing the MODE ESC button The unit will automatically exit the menus if no buttons are pressed after 10 seconds These next pages will explain each func tion in the menu layout located on the previous page FUNCTION DMX Address With this function you can adjust the desired DMX address via the Control Board 1 Access the main menu and press the UP or DOWN buttons so that Function is higlighted then press ENTER 2 Press the UP or DOWN buttons until DMX Address is displayed and press ENTER The current DMX address will now be displayed 3 Use the UP or DOW
51. om the fix ture Failure to change the lamp within 300 hours of operation will result in automatic shut down of the fixture s electronics At 6000 hours the display will begin to flash Replace The Lamp and the lamp will flicker for the first five minutes of operation At this point the lamp has reached the maximum rated life and should be replaced immediately After the lamp has flickered for about five minutes it should strike normally allowing the fixture to be used tempo rarily until a replacement lamp can be installed The fixture will continue to operate for an additional 300 hours however the Replace the Lamp warning will continue to flash in the display Keep in mind that the flicker protection circuitry will only work for about 300 hours lamp clock life of 6000 6300 hours After 6300 hours the fixture will no longer respond to DMX commands and immediately enter a hibernation mode that will electronically discontinue all fixture functionality with the exception of a few menu commands The fixture will continue to enter hibernation mode until the lamp is replaced and the lamp clock has been reset See page 22 to Clear the lamp time ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 7 3 Sixty 2R When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g a
52. one of ten of the user defined built in programs This program is then accessed in Function Mode under Program Run Edit Program This function allows the user to edit the built in pro grams Edit Scenes This function allows the user to edit or define the ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 37 3 Sixty 2R System Menu actual scenes that are stored in the user defined built in programs that are accessed in the previous step Rec Controller The 3 Sixty 2R features an integrated DMX recorder Preprogrammed scenes can be transmitted to the fixture via any DMX compliant controller This function allows those scenes to be stored in to the fixture s built in memory and then subsequently used to create the user defined programs ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 38 3 Sixty 2R Error Codes When power is applied the unit will automatically enter a reset test mode This mode brings all the internal motors to a home position If there is an internal problem with one or more of the motors an error code will flash in the display in the form of XXer XX will represent a function number For example when the display shows O3Er it means there is some type of error with the channel 3 motor If there are multiple errors during the start up process they will all flash in the display For exam ple if the fixtures has errors on channel 1 and
53. rnal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 65 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 4 3 S
54. seicosenccsstat2cmennanduatanaeeeeednaetsshanambanontengosaoee DDS CITIC ATOMS cesataiteascediuicnnnsandpainensqsdhaskacaahatnatinnoaddrsddeanata Please see page 7 for important lamp instructions ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 2 3 Sixty 2R General Information Unpacking Thank you for purchasing the 3 Sixty 2R by ADJ Prod ucts LLC Every 3 Sixty 2R has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact In the event damage has been found or parts are miss ing please contact our toll free customer support number for further instructions Please do not return this unit to your dealer without con tacting customer support first Introduction The 3 Sixty 2R is a DMX intelligent moving head fix ture The 3 Sixty 2R can be a 21 channel 24 channel or 32 Channel DMX unit The fixture can operate in three different operating modes show mode sound active or under DMX control The 3 Sixty 2R can be used as a stand alone unit or in a master slave configuration For best results use fog or special effects smoke to enhance the beams projections During the initial start up or use of this product a light smoke or smell may arise from the uni
55. sure to dry all parts completely before plugging the unit back in 3 Sixty 2R Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions w N No light output from the unit 1 Be sure the external fuse has not blown The fuse is located on the bottom panel of the unit 2 Remove the lamp holder and be sure the lamp is seated in its socket properly Occasionally lamps become loose during ship ping be sure the lamp is push in to its socket all the way 3 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 65 3 Sixty 2R Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return
56. t will shorten lamp life Also never move the fixture until the lamps have had ample time to cool Remember lamps are without it s covers these covers have been specially designed to shield against UV radiation not covered under warranty conditions Epileptic Warning Those suffering from epilepsy should avoid looking directly into the lamp at all times Avoid switching the fixture on and off repeatedly in short intervals as this will reduce lamp life and intensity To achieve the intensity associated with discharge lamps these lamps use gas sealed in a high pressure environment to emit a brilliant output Due to the high pressure involved with the construction of the lamp the lamp may explode during prolonged extensive use This risk is increased with age added care is encouraged when dealing with older lamps Extreme caution should be used when operating this or any fixture fitted with a gas discharge lamp Never open this unit while in use VERY IMPORTANT This is for your safety and the life length of the unit The Philips Platinum 2R Discharge lamp has lifetime of 6 000 hours Because of the nature of the extreme heat associated with the Platinum 2R lamp and the tight nature of the internal optical system it is imperative that the lamp be replaced every 6000 hours This is done to protect the internal optical system as well as prevent accidental lamp explosion which could lead to hot glass particles falling fr
57. t This is a normal process and is cause by the heat associated with the lamp Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 823 582 2610 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 3 3 Sixty 2R Safety Precautions For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an inte
58. tains a electronic ballast which will auto sense the voltage when it is plugged into the power source With the electronic ballast you do not need to worry about wall voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address
59. ten warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LEDs and lamps e Laser Products 90 Day Limited Warranty L ED Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 66 3 Sixty 2R Notes 3 Sixty 2R Notes ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 67 ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 68 3 Sixty 2R Specifications Model 3 Sixty 2R Voltage 100 240V 50 60Hz Lamp 2 x 135W Philips MSD Platinum 2R Discharge Lamps Beam Angle 4 Degrees Power Consumption 400W Total Dimensions 17 L x 13 W x 18 75 H 428mm x 326mm x 473mm Colors 13 White Gobos 14 Spot Weight 45 Lbs 20 3 kgs Fuse 7A Duty Cycle None DMX 3 DMX Channel Modes 21 Channels 24 Channels or 32 Channels Sound Active Yes Working Position Any Safe Secure Position Warr
60. ts LLC www adj com 3 Sixty 2R Instruction Manual Page 23 3 Sixty 2R System Menu tons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit Lamp on via DMX External Controller With this function you can select if you want to switch the lamp on via an external controller This is used in conjuction with Internal Programs DMX channel DMX values 40 59 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Lamp On Via DMX is dis played press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between Select On if you wish to activate this func tion or Off to deactivate 4 Press ENTER to confirm your selection or press MODE ESC to exit Lamp off via DMX External Controller With this function you can select if you want to switch the lamp off via an external controller This is used in conjuction with Internal Programs DMX channel DMX values 60 79 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Lamp Off Via DMX is dis played press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between Select On
61. ttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until Feedback is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Movement Speed With this function you can set the pan and tilt movement speed 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Settings is dis played press ENTER 3 Press UP or DOWN buttons until Movement Speed is dis played and press ENTER 4 Either Speed 1 Speed 2 Speed 3 or Speed 4 will be dis played use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 29 3 Sixty 2R System Menu exit Mic Sensitivity With this function you can set the microphone sensitivity The default setting is 70 You can adjust the sensitivity between 0 99 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons unti
62. ty for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit 3 Sixty 2R Product Registration The 3 Sixty 2R carries a one year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our toll free customer support number All packages returned to the service department not displaying a R A number on the outside of the package will be returned to the shipper at the shippers cost ADJ Products LLC www adj com 3 Sixty 2R Instruction Manual Page 6 3 Sixty 2R Important Discharge Lamp Warning G y This fixture is fitted with a discharge lamp which is highly susceptible to damage if improperly handled Never touch the lamp with your bare fingers as the oil from your hands This unit emits intense UV radiation which is harmful to the eyes and skin The intense luminance of the lamp can cause severe damage to the retina Never operate this uni
63. uto run if no DMX Pan Reverse ON GFE Pan Reverse movement Tilt_L Reverse ON OFE Tilt_L Reverse Tilt_R Reverse ON OFE Tilt_R Reverse Pan Degree 540 630 Pan Degree Select Feedback ON OFF Movement Feedback Movement Speed Spei 4 Movement Mode Select z Mic Sensitivity 0 99 Sensitivity of Mic 3 Hibernation OFF 01M 99M 15M Stand by Mode 8 Service Setting Password Password XXX Service Password 050 2 RDM PID XXXXXX RDM PID Code Display Setting Shutoff Time 02 60m 05m Display shutoff time Display Reverse ON OFF Reverse 180 degree Key Lock ON OFF Key Lock Temperature C F Celsius Temperature switch Fahrenheit between C Initial Status PAN XXX Initial effect position Reset Default ON OFF Restore factory set Reset All Reset all motors Reset Pan amp Tilt Reset Pan Tilt 2 Reset Colors Reset color wheel S Reset Gobos Reset gobos Reset Shutter Reset shutter or dimmer Reset Others Reset other motors Test Channel PAN oes Test function Manual Control PAN XXX Fine adjustment of the 5 lamp Calibration Calibrate Password Password 050 Color wheel XXX Calbrate and adjust the effects to standard right position User Mode Standard Mode User s mode to change Basic Mode channel numbers 3 Extended Mode 3 User Mode A User Mode B 5 User Mode C 5 Edit User Mode Max Channel XX Preset User modes A B C PAN CH01 Select Programs Auto Pro Part 1 Program 1 10 progami Select programs to be Auto Pro Part 2 Pr
64. xty 2R System Menu 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit RESET FUNCTION Reset All With this function you can reset all the motors 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset All is displayed 3 Press ENTER to reset or press MODE ESC to exit Rest Pan amp Tilt With this function you can reset the Pan amp Tilt motors 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Pan Tilt is dis played 3 Press ENTER to reset or press MODE ESC to exit Reset Colors With this function you can reset the color wheel motor 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Colors is displayed 3 Press ENTER to reset or press MODE ESC to exit Reset Gobos With this function you can reset the gobo wheel motor 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then ADJ Products LLC
65. y 2R System Menu 5 Press ENTER or press MODE ESC to exit Software Version This will allow you to see the software version you are currently running 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Software Version is dis played press ENTER 3 VX X will now be displayed X X represents the software ver sion 4 Press ENTER or press MODE ESC to exit LAMP CONTROL Lamp On Off With this function you can switch the lamp on or off via the control board 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Lamp On Off is displayed press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit Automatic On With this function you can have the lamp automati cally turn On when when switching on the power 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Automatic On is displayed press ENTER 3 Either Off or On will be displayed use the UP and DOWN but ADJ Produc

3 Sixty 2R - Performance Audio

Contents

Download Pdf Manuals

Related Search

Related Contents