Owner`s Manual Rackmount Network Switch with Built
Contents
1. radio transmitting stations transmitters and broadband amplifiers Use electromagnetic shielding if required For rackmount configuration ensure that both the rack and switch are properly grounded e f the switch is not rack mounted securely place it on a sturdy flat surface Improper installation can cause product damage that is not covered by the warranty Do not expose the network switch s connected networking cables to outdoor elements Do not use this product near water e g in a wet basement or near a swimming pool PDU Switch Connection Warnings Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended Do not use this equipment in the presence of a flammable anesthetic mixture with air oxygen or nitrous oxide Keep the switch s input power off during installation Use only the power cord that came included with the switch Make sure the power supply voltage matches the specifications indicated on the switch he total power requirement for equipment connected to the switch must not exceed the maximum load rating for the PDU s circuit breaker Do not connect the switch to an ungrounded outlet or to extension cords or adapters that eliminate the connection to ground Do not drill into or attempt to open any part of t2. revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitutes claims by third parties or otherwise PRODUCT REGISTRATION Visit www tripplite com warranty today to register your new Tripp Lite product You ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product No purchase necessary Void where prohibited Some restrictions apply See website for details Regulatory Compliance Identification Numbers For the purpose of regulatory compliance certifications and identification your Tripp Lite product has been assigned a unique series number The series number can be found on the product nameplate label along with all required approval markings and information When requesting compliance information for this product always refer to the series number The series number should not be confused with the marketing name or model number of the product FCC Notice Class A This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference wh
3. Owners Manual Rackmount Network Switch with Built in PDU Model NSU G16 Series Number AG 00C6 PROTECT YOUR INVESTMENT Register your product for quicker service and ultimate peace of mind You could also win an ISOBARGULTRA surge protector a 50 value u www tripplite com warranty TRIPPLITE ER EARS f Excellence 1111 W 35th Street Chicago IL 60609 USA www tripplite com support Copyright 2014 Tripp Lite All rights reserved 14 09 040 9332E0 indd 1 9 8 2014 2 35 07 PM Important Safety Instructions SAVE THESE INSTRUCTIONS This manual contains important instructions and warnings that should be followed during the installation operation and storage of this Tripp Lite product Failure to heed these warnings may affect your warranty PDU Switch Location Warnings The switch provides the convenience of multiple outlets but DOES NOT provide surge or line noise protection for connected equipment The switch is designed for indoor use only in a controlled environment away from excess moisture temperature extremes conductive contaminants dust or direct sunlight e For best performance maintain an indoor temperature between 32 F and 104 F 09 C and 40 C with relative humidity between 10 and 90 non condensing Leave adequate space around all sides of the switch for proper ventilation Keep the switch away from high frequency strong current devices e g
4. ation 2 Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of two 2 years from the date of initial purchase TRIPP LITE s obligation under this warranty is limited to repairing or replacing at its sole option any such defective products To obtain service under this warranty you must obtain a Returned Material Authorization RMA number from TRIPP LITE or an authorized TRIPP LITE service center Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase This warranty does not apply to equipment which has been damaged by accident negligence or misapplication or has been altered or modified in any way EXCEPT AS PROVIDED HEREIN TRIPP LITE MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not permit limitation or exclusion of implied warranties therefore the aforesaid limitation s or exclusion s may not apply to the purchaser EXCEPT AS PROVIDED ABOVE IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Specifically TRIPP LITE is not liable for any costs such as lost profits or
5. d 8 9 8 2014 2 35 31 PM
6. e commutateur a puissance totale requise pour l quipement connect au commutateur ne doit pas exc der la charge nominale maximum pour le disjoncteur de la PDU Ne pas connecter le commutateur dans une prise non mise la masse ou des rallonges lectriques ou des adaptateurs qui liminent la connexion la masse Ne pas percer ou tenter d ouvrir une quelconque partie du bo tier du commutateur Il n existe aucune pi ce r parable par l utilisateur l int rieur Ne pas tenter de modifier le commutateur y compris les fiches d entr e et les c bles d alimentation Ne pas tenter d utiliser le commutateur si une de ses pi ces est endommag e e S assurer que les cables du r seau reposent correctement en place Un bruit de cliquetis sera mis lorsqu un c ble est install correctement Sile cordon d alimentation est endommag ne pas tenter de connecter le commutateur Contactez votre repr sentant e Tripp Lite pour obtenir de l aide Ne jamais essayer d installer ou d utiliser le commutateur pendant un orage 3 14 09 040 9332E0 indd 3 9 8 2014 2 35 07 PM Product Features Front Panel Gigabit Ethernet Ports These 16 twisted pair RJ 45 ports support auto negotiable 10 100 1000 Mbps and auto MDI MDIX cross over detection functions for true plug and play capability There are two green LEDs per RJ 45 port The left LED blinks when the port is active The right LED is off at 10 and 100 Mbps and l
7. en the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense The user must use shielded cables and connectors with this equipment Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the user s authority to operate this equipment WEEE Compliance Information for Tripp Lite Customers and Recyclers European Union Under the Waste Electrical and Electronic Equipment WEEE Directive and implementing regulations when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to e Send old equipment for recycling on a one for one like for like basis this varies depending on the country BEE Send the new equipment back for recycling when this ultimately becomes waste The policy of Tripp Lite is one of continuous improvement Specifications are subject to change without notice 14 09 040 9332E0 indd 6 9 8 2014 2 35 30 PM 14 09 040 9332E0 indd 7 9 8 2014 2 35 30 PM Excellence 1111 W 35th Street Chicago IL 60609 USA www tripplite com support 8 14 09 040 93 32E0_revC 14 09 040 9332E0 ind
8. he switch housing There are no user serviceable parts inside Do not attempt to modify the switch including the input plugs and power cables Do not attempt to use the switch if any part of it becomes damaged Make sure network cables are properly seated A clicking sound will be made when a cable is installed correctly e f the power cord is damaged do not attempt to connect the switch Contact a Tripp Lite Service Representative for assistance Never attempt to install or use the switch during a thunderstorm 2 14 09 040 9332E0 indd 2 9 8 2014 2 35 07 PM Important Safety Instructions Avertissement concernant l emplacement de la PDU du commutateur e Le commutateur fournit des prises multiples pratiques mais elle ne FOURNIT PAS de protection contre les surtensions ou les bruits de ligne pour l quipement connect Le commutateur est concue pour tre utilis e a l int rieur uniquement dans un environnement contr l l cart de l exc s d humidit des temp ratures extr mes des contaminants conducteurs de la poussi re et de la lumi re directe du soleil e Pour un rendement optimal maintenez la temp rature int rieure entre 32 F et 104 F 0 C et 40 C avec une humidit relative comprise entre 10 et 90 96 sans condensation aisser suffisamment d espace tout autour du commutateur pour assurer une bonne ventilation e Garder le commutateur l cart des appareils haute fr quence e
9. ights up at 1000 Mbps remaining lit while at that speed Note Not compatible with PoE Power Over Ethernet applications Power ON OFF LED An LED illuminates to indicate that the switch is receiving power NEMA 5 15R Outlets This switch includes eight NEMA 5 15R receptacles Circuit Breaker If the current drawn by the equipment connected to the PDU exceeds the Maximum Load Rating the 12A thermal circuit breaker will trip to prevent possible damage and its plunger will pop up If this happens disconnect excess equipment and allow the breaker to cool at least one minute before depressing the plunger to reset the unit E Input AC power input from a connected UPS system or alternate source G Grounding Lug Use this screw to connect your switch to ground 14 09 040 9332E0 indd 4 9 8 2014 2 35 07 PM 1U Rackmount Installation Mount the switch using either the four cage nuts EY washers GJ and screws provided or four user supplied rackmount screws 0 The user must determine the fitness of the rackmount screws to hold the unit in the rack before installation EB Connect the switch to a properly grounded outlet The POWER LED will illuminate when the switch turns on 3 Connect the network cables to the network switch E Connect equipment to the PDU outlets Make sure the load connected does not exceed the PDU s circuit breaker rating 14 09 040 9332E0 indd 5 9 8 2014 2 35 29 PM Warranty amp Product Registr
10. t courant fort p ex station mettrice de radio transmetteurs et amplificateurs large bande e Utiliser une protection lectromagn tique le cas ch ant Pour une configuration de montage en b ti s assurer que le b ti et le commutateur sont correctement mis la masse e Si le commutateur n est pas mont en b ti le placer solidement sur une surface solide et plat Une mauvaise installation risque de causer des dommages au produit qui ne sont pas couverts par la garantie Ne pas exposer les c bles de r seautage connect s du commutateur r seau aux l ments ext rieurs Ne pas utiliser ce produit proximit de l eau p ex dans un sous sol humide ou proximit d une piscine Avertissement concernant la connexion de la PDU du commutateur e n est pas recommand d utiliser cet quipement dans les applications de soutien vital ou une panne de cet quipement serait susceptible de causer une panne de l quipement de soutien vital ou d affecter s rieusement sa s curit ou son efficacit Ne pas utiliser cet quipement dans un milieu ou il existe un m lange anesth sique inflammable avec de l air de l oxyg ne ou de l oxyde nitreux e Garder l alimentation d entr e du commutateur hors tension durant l installation Utiliser uniquement le cordon d alimentation qui tait fourni avec le commutateur e S assurer que la tension d alimentation correspond aux sp cifications indiqu es sur l
Download Pdf Manuals
Related Search