Home

Operations

1. _ OPERATOR MANUAL MODELS CF24E CF36 46 4 Blades POWER TROWEL 100 employee owned American manufacturer REVISION D 2 2002 P N 56353 Table of Contents CE Power Trowel TABLE OF CONTENTS FOREWORD LIMITED WARRANTY TECHNICAL DATA Specifications Torque Chart Imperial Torque Chart Metric Hardware Identification HEALTH amp SAFETY Safety Training Safety Precautions Operating Principle Delivery Checks Before Starting Determining the Right Machine Standard Features Preparation for Service Location and Use of Controls Adjust Tilt Lock Nut OPERATIONS To Start To Shut Off Initial Operation Floating Operation Finishing Operation MAINTENANCE Maintenance Lubrication and Adjustment Lubrication Trowel Gearcase Arm Bearing CALIFORNIA PROPOSITION 65 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS AND OTHERS PENDING 4046483 4232980 CAN 1131361 DYNA CLUTCH is a trademark of the Manufacturer These instructions include Please enter the following data This will help expedite any service or warranty work Safety regulations Operating instructions l Machine Maintenance instructions Machine S N These instructions have been prepared for operation on the construction site and for the maintenance Engine Type engineer Engine S N These instructions are intended to simplify operation of the machine and to av
2. 9926 Fax 716 229 2363 e mail sceny mcimail com www stone equip com 100 employee owned American manufacturer 1984 Stone Construction Equipment Inc Printed in U S A SCE
3. turn the control clockwise To unlock the throttle for further adjustments turn the control counter clockwise approximately 1 4 turn Location and Use of Controls DYNA CLUTCH LEVER this is a patented feature which acts as a safety device to stop the trowel from spinning out of control if the operator lets go of the handle It also allows the operator to control the engagement and disengagement of the trowel blades independent of engine speed To use simply move the lever all the way up to the RUN position to engage the trowel blades To stop the blades from turning push the lever all the way down to STOP position In the event that the operator lets go of the handle while the blades are turning the centrifugal force from the swing of the handle will throw the Dyna Clutch lever to the STOP position This prevents the unit from spinning out of control and causing injury to personnel or damage to the trowel and fresh concrete Since the Dyna Clutch system disengages the blades from the engine rather than shutting down the engine to stop the blades time is saved in getting the unit operating again The operator simply moves the Dyna Clutch lever to RUN position instead of having to restart the engine and readjust engine speed TILT ADJUSTMENT KNOB adjusts the angle of the blades for different curing stages and conditions of the concrete Turning the knob clockwise increases the angle of the blades to the concrete Turni
4. 1 4 5 x9 12 7 x 22 9 Self aligning aircraft bearings positive blade positioning inf var blade leveler 4 hp Honda 2 98 4 5hp Robin 3 36 50 130 8 2 1 Hardened steel worm and bronze gear cast aluminum gearbox tapered roller bearing Patented Dyna Clutch Reinforced contoured T handle Throttle tums w 1 4 tum locking castiron rotating hand lift oil sight gauge assembled cushioned handgrips rotating guard 2 yeargearcase STONE CF364 160 185 Ibs 72 7 84 36 91 5 4 6 x 14 15 2 x 35 6 8 x 14 20 3 x 35 6 10 x 14 25 4 x 35 6 Self aligning aircraft bearings positive blade positioning inf var blade leveler 5 hp B amp S 3 7 5 hp B amp S 3 7 8hp B amp S 5 9 5 5 hp Honda 4 1 8 hp Honda 5 9 6hp Robin 4 47 9hp Robin 6 71 50 130 8 2 1 Hardened steel worm and bronze gear cast aluminum gear box tapered roller bearings Patented Dyna Clutch Reinforced triple tube contoured adjustable T handle Throttle tums w 1 4 tum locking castiron rotating standard oil sight gauge assembled cushioned handgrips shock mounted stationary guard 2 yeargearcase SIONE CF464 180 225 lbs 82 102 3 46 116 4 6 x18 15 2 x 45 7 8 x 18 20 3 x 45 7 10 x 18 25 2 x 45 7 Self aligning aircraft bearings positive blade positioning inf var blade leveler 8 hp B amp S
5. 375 23 ft lbs 31 Nm 7 16 14 4375 37 ft lbs 50 Nm 1 2 13 500 57 ft lbs 77 Nm 9 16 12 5625 82 ft lbs 111 Nm 5 8 11 625 112 ft lbs 152 Nm 3 4 10 750 200 ft lbs 271 Nm 7 8 9 875 322 ft lbs 436 5 Nm 1 8 1 000 483 ft lbs 655 Nm SAE GRADE 5 Fine Thread SIZE PLATED 1 4 28 250 7 ft lbs 5 16 24 3125 14 ft lbs 3 8 24 375 26 ft lbs 7 16 20 4375 41 ft lbs 1 2 20 500 64 ft lbs 9 16 18 5625 91 ft lbs 5 8 18 625 128 ft lbs 3 4 16 750 223 ft lbs 875 355 ft lbs 529 ft lbs 1 14 1 000 541 ft lbs SAE GRADE 8 Coarse Thread SIZE PLATED 1 4 20 250 9 ft lbs 5 16 18 3125 18 ft lbs 3 8 16 375 33 ft lbs 7 16 14 4375 52 ft lbs 1 2 13 500 80 ft Ibs 9 16 12 5625 115 ft lbs 5 8 11 625 159 ft lbs 3 4 10 750 282 ft lbs 7 8 9 875 454 ft lbs 1 8 1 000 682 ft lbs SAE GRADE 8 Fine Thread SIZE PLATED 1 4 28 250 10 ft lbs 5 16 24 3125 20 ft Ibs 3 8 24 375 37 ft lbs 7 16 20 4375 5
6. 8 ft lbs 1 2 20 500 90 ft Ibs 9 16 18 5625 129 ft lbs 5 8 18 625 180 ft Ibs 3 4 16 750 315 ft lbs 7 8 9 875 501 ft lbs 1 12 1 000 746 ft lbs 1 14 1 000 764 ft lbs Technical Data Torque Chart Metric Property Class 8 8 ZINC PLATED Coarse Thread Fine Thread ME 9 9 7 10 M8 24 25 M10 48 49 M12 83 88 M14 132 M16 200 M20 390 M24 675 Property Class 10 9 ZINECREATED Coarse Thread Fine Thread 1 165 Nm ft Ibs 14 10 14 10 M6 M8 34 25 35 26 M10 67 49 68 50 M12 117 86 125 92 Mi4 185 136 192 142 M16 285 210 295 218 M20 550 406 600 443 M24 950 701 1000 738 Property Class 12 9 ZINC PLATED Coarse Thread Fine Thread M6 16 5 12 16 5 12 M8 40 30 42 31 10 81 60 82 60 12 140 103 150 111 14 220 162 235 173 Mt6 340 251 258 M20 660 487 531 M24 1140 841 885 Conversion Factor 1 ft 1 3558 Nm Technical Data HardwareKey HHCS GR8 HHCS GR des LC Lum BHCS SHSS CUP PT THD ROD mm 2 mmi WSHR SAE N WSHR BELLEVILLE 10 Health amp Safety Safety Training SAFETY
7. AND TORQUE CHART section of this manual for general guidelines and recommendations and tighten any suspicious hardware OIL LEVEL AND LUBRICATION Check the oil level in the engine and gearbox Engine and trowel warranties are VOID if this unit is run without oil Also check the blade arms and thrust bearing to make sure they have been greased Consult the GENERAL LUBRI CATION SECTION of this manual for lubrica tion requirements and instruction if required FUEL Fill the fuel tank on gasoline engines with clean gasoline from a safety can DO NOT mix oil with the gasoline AWARNING FOLLOW SAFETY PRECAUTIONS WHENEVER HANDLING GASOLINE edes Introduction LOCATION AND USE OF CON TROLS Before operating this trowel it is important to familiarize yourself and any other personnel who will be using it with the location and proper use of the controls to insure safe and efficient operation A HANDLE ADJUSTMENT KNOB to adjust the handle for maximum operator comfort and control simply turn the knob counterclockwise one quarter turn maxi mum to loosen move handle to desired position and tighten knob to lock handle in place THROTTLE CONTROL this is a push pull type throttle control which can be locked at any desired blade speed from 50 to 130 RPM to meet varying job conditions To use simply push or pull the throttle control to obtain the desired blade speed To lock the throttle at the speed
8. HP amp 8 HP B amp S ENGINES close throttle all the way flip grounding tab against spark plug and hold there until the engine comes to a complete stop 4 5 5 amp 8HP HONDA ENGINES close throttle all the way and flip oil minder kill switch to the OFF position 4 5 8 amp 9 HP ROBIN ENGINES close throttle all the way depress kill switch button and hold down until engine stops completely NOTE These stopping instructions are general guidelines only consult the ENGINE MANUAL included with the unit for specific instructions INITIAL OPERATION With engine started as instructed previously and at operating tem perature adjust speed to about half throttle Hold the handle firmly with one hand and move the Dyna Clutch lever to RUN position to engage the trowel blades FLOATING OPERATION Attach float or combination blades to the trowel arms and when the concrete has set sufficiently to support the weight of the trowel place the unit on the concrete Start the unit and engage the blades as previously instructed Using the tilt adjustment knob or ProPitch handle adjust the blades to the float position blades should be as flat to the concrete as possible with enough tension kept on the tilt adjustment cable to prevent the unit from dancing or chattering Guide the trowel over the concrete in a circular back and forth motion Under normal condi tions you should be able to float a 30 x 30 foot area in approximately 15
9. I P 5 9 8 hp Honda 5 9 9hp Robin 6 71 50 130 8 2 1 Hardened steel worm and bronze gear cast aluminum gearbox tapered roller bearings Patented Dyna Clutch Reinforced triple tube contoured adjustable T handle Throttle tums w 1 4 tum locking castiron rotating standard oil sight gauge assembled cushioned handgrips shock mounted stationary guard 2 yeargearcase Machine Sound and Vibra Technical Data tion Measurements Sound and Vibration Measurements Sound Pressure Values as measured are perthe following Sound Pressure CF36 CF46 5 5 Honda 8 Honda 92dBA 93dBA RMS acceleration on the handle were measured perthe following meter sec 7 6 Sound and vibration valueshave been taken in accordance to the EEC machine regulation edition 93 68 EEC Sound Pressure measurements were taken with Simpson model 886 2 type 2 meter calibrated 1 31 98 Acceleration measurements were taken with Quest Tech model VI 100 meter calibrated 4 17 96 Sound and vibration measurements were obtained with machine operating at maximum engine speed of 3600 RPM Unit measurements were taken on steel test plate cA winnt bonnie sound cf feb 2000 doc Technical D ata Torque Chart Imperial SAE GRADE 5 Coarse Thread SIZE PLATED 1 4 20 250 6 ft lbs 8 Nm 5 16 18 3125 13 ft lbs 18 Nm 3 8 16
10. These machines are designed to carry out the function of finishing concrete surfaces If used correctly they will provide an effective and safe means of finishing and meet the appropriate performance standards It is essential that the operator of the machine is ad equately trained in its safe operation be authorized to operate it and have sufficient knowledge ofthe machine to ensure that it is in full working order before being put to use idis Health amp Safe Safety Precautions Before using this equipment study the entire owner s manual AWARNING to become familiar with its operation Do not allow un trained or unauthorized personnel especially children to operate this equipment Use only factory authorized parts for service When warning decals are destroyed or missing contact the Manufacturer immediately at 1 800 888 9926 for replace ment For the safety of yourself and others it is imperative that the following rules are observed Failure to do so may result in serious injury or death USE COMMON SENSE WHEN HANDLING FUELS Transport and handle fuel only when contained in approved safety containers Do not smoke when refueling the engine or during any other fuel handling operation Do not refuel the unit with the engine running or while hot If fuel is spilled during refueling wipe it off from the en gine immediately and discard the rag in a safe place Do not operate the unit if
11. area Avoid prolonged breathing of exhaust gases uj Intro Operating Principle Deliv ery Checks Before Starting Introduction Determining the Right Machine Congratulations on your purchase of Stone Smooth Operator Power Trowels You ve made an excellent choice The Power Trowels have been specifically designed as the ideal machine for the contractor who is engaged in professional concrete finishing Upon receipt of your Smooth OperatorTM Power Trowel CAREFULLY CHECK FOR ANY FREIGHT DAMAGE Any damage should be immediately reported to the carrier and a claim registered The Smooth Operator Power Trowel is manu factured to the strictest specifications and inspec tion procedures If any material or manufacturing defects are found return the tag on the machine with assembler s signature and your findings to the manufacturer We want to know when a prod uct is less than perfect We also welcome any and all input on how the product may serve you better OPERATING PRINCIPLE The following instructions were compiled to provide you information on how to obtain long and trouble free use of the unit Periodic maintenance of this unit is essential Read the manual in its entirety and follow the instructions carefully Failure to do so may injure yourself or a bystander DELIVERY CHECKS Immediately on taking delivery of your new equipment and before putting it into service Read the handbook c
12. fuel or oil leaks exist repair immedi ately Never operate this equipment in an explosive atmosphere Never perform any work on the unit while it is running Before working on it stop the engine and disconnect the spark plug wire to prevent accidental starting Do not operate this unit without all guards in place Keep hands feet clothing and jewelry away from the unit blades and all moving parts Rotating and moving parts will cause serious injury if contacted during operation Do not allow anyone to stand or lean on the unit during operation dors Health amp Safe Safety Precautions Keep the patented Dyna Clutch safety system in adjustment and good operating condition at all times Do not operate the trowel if it does not work properly Out of control Trow els can cause serious personal injury and damage to fresh concrete surfaces The Dyna Clutch system will automati cally stop the unit if the operator loses control of it during operation Make sure the Dyna Clutch is disengaged lever in the down position before starting the unit Keep one hand firmly on the handle while starting and do not let go of the handle during operation Avoid contact with hot exhaust systems and engine parts Allow engine to cool before performing any repairs or service WW EAN 0 Ear protection required when operating this equipment Never operate any gas powered equipment in a poorly ventilated or enclosed
13. in the tilt cable when the ProPitch handle is in full tilt position With handle in full tilt position adjust the nut on the backside of swivel at the upper end of linkage rod until the proper gap is achieved between the tilt lever and the gearcase approximately 1 64 inch Tighten nut on the outside of swivel to lock linkage rod into position Repeat adjustment if required NOTE Cables may stretch over time and may need to be replaced if full tilt is no longer obtainable Refer to Service and Parts Manual for full diagram and parts break down SWIVEL LINKAGE 17 To Start To Shut Off Inital Op eration Floating Operation O erations Finishing Operation TO START Make sure the Dyna Clutch lever is in the STOP position If it is not push the lever down to the STOP position before at tempting to start the engine Open fuel valve under fuel tank if so equipped open throttle approximately half way down and apply choke Holding unit handle firmly with one hand pull the starter rope sharply with the other about 3 times When engine starts open choke and adjust throttle as necessary to keep it running If engine doesn t start after 3 pulls open choke slightly NOTE These starting instructions are general guidelines only Since many engine options are available on CF Power Trowels consult the ENGINE MANUAL included with the unit for specific instructions TO SHUT OFF 5
14. ion of the products and the fact hereof or as to operational efficiency product reliability or maintainability or compatibility with products furnished by others In no event whether as a result of breach of contract or warranty or alleged negligence shall the Manufacturer be liable for special or consequential damages including but not limited to Loss of profits or revenues loss of use of the product or any associated product cost of capital cost of substitute products facilities or services or claims of customers No claim will be allowed for products lost or damaged in transit Such claims should be filed with the carrier within fifteen days Effective April 1 1998 lone A M 7 EA POE AA OA 5 Ki T 7i ree e pu a Lk US rue Sone ees Equipment Inc Phone 1 800 888 9926 1 716 229 5141 Bred Tough Born To Work The 32 East Main Street P O Box 150 Fax 1 716 229 2363 Way It Ought To Be Honeoye NY 14471 0150 www stone equip com e mail sceny mcimail com 4 98 P N 51018 Technical Data Trowels Specifications MODEL Dimensions Operating Wt kg Diameter cm Blades Number Finish cm Combination cm Hoat cm Blade Positioning Blade Leveler RPM S Hertz GearBox Standard Features Safety Shutoff Handle Spider Stabilizing Ring Lifting Eye Gauges Shipped Other Features STONE CF24E 130 Ibs 59 24 6
15. l throttle control can be set to provide any blade speed from 50 to 130 RPM and located in place at the desired operating speed BENT ARM ADJUSTMENT Allows blades to be adjusted to compensate for bent arms caused by dropping or mishandling the trowel Can be easily adjusted on site for consistent finishing HEAVY DUTY RING GUARD Protects operator and unit while providing lower center of gravity which contributes to unit stability and performance CAST IRON SPIDER Extra strong houses a double set of replaceable nylon bearings for each blade arm to insure alignment and elimi nate seizing Also contributes to lower center of gravity for increased trowel performance ADJUSTABLE HANDLE Can be posi tioned to provide comfort and control for any operator s height Equipped with flanged and cushioned motorcycle style hand grips to absorb vibration and minimize operator fatigue Standard Features Preparation for Service PREPARATION FOR SERVICE BEFORE STARTING Your new CF Power Trowel has been assembled and tested at the factory However before placing the unit into service the following items should be checked ASSEMBLY AND HARDWARE The unit is shipped completely assembled except for installation of the adjustable handle Consult the HANDLE ASSEMBLY exploded diagram and assemble the adjustable to the main handle with handle adjustment knob as shown Next check all hardware on the unit and engine Consult the HARDWARE
16. ment in applications for which it was not intended use of non manufacturer parts or failure to follow documented service instructions The foregoing warranty is exclusive of all other warranties whether written or oral expressed or implied No warranty of merchantability or fitness for a particular purpose shall apply The agents dealer and employees of Manufacturer are not authorized to make modification to this warranty or additional warranties binding on Manufacturer Therefore additional statements whether oral or written do not constitute warranty and should not be relied upon The Manufacturer s sole responsibility for any breach of the foregoing provision of this contract with respect to any product or part not conforming to the Warranty or the description herein contained is at its option a to repair replace or refund such product or parts upon the prepaid return thereof to location designated specifically by the Manufacturer Product returns not shipped prepaid or on an economical transportation basis will be refused b as an alternative to the foregoing modes of settlement the Manufacturer s dealer to repair defective units with reimbursement for expenses except labor and be reviewed with the Manufacturer prior to repair A Warranty Evaluation Form must accompany all warranty claims Except as set forth hereinabove and without limitation of the above there are no warranties or other affirmations which extends beyond the descript
17. minutes This operation will bring the water and fines to the surface allowing for a smoother finish when finishing the concrete FINISHING OPERATION After floating allow the concrete to set until it will support the weight of the trowel Set the pitch to approximately 1 4 to 3 8 on the blades If the blades start to dig into the con crete decrease the amount of pitch 18 Maintenance MAINTENANCE LUBRICATION AND ADJUSTMENT To get long and trouble free service from your new CF Power Trowel it is essential to perform peri odic maintenance on engine and machine mecha nisms Follow the guidelines listed below LUBRICATION A ENGINE CRANKCASE Daily check oil level in engine Engine warranty is VOID if it is run without oil Add oil as re quired to keep crankcase full Engine oil should be changed every 250 hours of operation or once a year whichever comes first Maintenance Lubrication Ad justment Lubrication Trowel Gearcase Arm Bearing Oil requirements are as follows Temperatures above 40 F 4 C SAE 30 Temperatures below 40 F 4 C SAE 5W20 These oil requirements are general guidelines only for specific requirements consult the ENGINE MANUAL included with the unit B TROWEL GEARCASE Daily check oil level in gearcase Trowel war ranty is VOID if is run without oil Oil level should fill the sight plug located on the right side of the gearcase when the unit is at re
18. ng the knob counterclockwise flattens or decreases the angle of the blades ProPitch Handle Option adjusts the agnle of the blades for different curing stage and conditions of the concrete Lift handle upwards to increase angle of the blades to the concrete Depress trip button to release lock and decrease the angle of the blades 16 Introduction TO ADJUST TILT LOCK tilt lock nut is located on the tilt rod assembly Using the lifteye raise the trowel with an overhead crane Back off tilt knob until there is enough cable slack to access the tilt lock nut For more tilt loosen lock nut set screw and turn lock nut towards tilt knob 1 turn and lock set screw Crank knob to full tilt position and check clearance between the tilt lever and gearcase for 1 64 paper thickness Repeat adjustment if required NOTE Cables may stretch over time and may need to be replaced if full tilt is no longer obtainable TILT LOCK NUT URETHANE WASHER HANDLE TILT BLOCK TILT CABLE Adjust Tilt Knob Lock Nut Linkage Rod TO ADJUST ProPitch LINKAGE Rod The linkage rod is fastened to a yoke end and a swivel by two nuts To adjust follow the steps listed below Using the lifteye raise the trowel using an overhead crane The lower end of the linkage rod is connected to a yoke and held in place with two 2 nuts Loosen the nut on the upper end of the linkage rod to allow slack
19. oid malfunctions through im VIN proper operation Purchase Date Observing the maintenance instructions will increase the reliability and service life of the machine when used 5 Dealer Distributor Information on the construction site and reduce repair costs and downtimes Name Always keep these instructions at the place of use of Address the machine Only operate the machine as instructed and follow these instructions Phone Observe the safety regulations as well as the guide Fax lines of the civil engineering trade association Observe safety rules for the operation of equipment 6 Battery and the pertinent regulations for the prevention of Manufacturer accidents Battery Type Stone Construction Equipment Inc is not liable for the function of the machine when used in an improper Battery S N manner and for other than the intended purpose Location of above information Operating errors improper maintenance and the use of incorrect operating materials are not covered by the 1 Information on S N tag warranty 2 Information on engine tag The above information does not extend the warranty and liability conditions of business of Stone Construc Information on S N tag if applicable tion Equipment Inc Date you purchased machine Dealer machine was purchased from 6 Information on battery and battery warranty card Stone Construction Equipment Inc Bo
20. ompletely it could save a great deal of unnecessary expense e Read the engine manual supplied Check the general condition of the equipment has it been damaged during delivery Check engine oil level Check fuel levels Recommended lubricants are detailed in the Care and Maintenance section BEFORE STARTING These starting instructions are general guidelines only Consult the engine manual included with this unit for specific instructions DETERMINING THE RIGHT MACHINE CF24E Ideal compactness for small jobs CF364 Ideal all purpose size CF464 Utilized for jobs requiring maximum productivity The Stone Smooth Operator line provides the most popular sizes and configurations available Engine options and trowel sizes can accommodate any job Engines available 4 hp 5 5 hp 8 or 9 horsepower Honda Briggs or Robin with four finish or combo blade configurations in 24 36 and 46 diameters 14 Introduction STANDARD FEATURES Your new CF Power Trowel comes standard with many features to enhance productivity performance and safety Listed below are just a few of these features DYNA CLUTCH Patented safety device automatically stops blade rotation without shutting down the engine if the trowel gets away from the operator Prevents injury to personnel and damage to the trowel and fresh concrete surfaces ADJUSTABLE THROTTLE Located in a convenient location this push pul
21. st on a level sur face Add oil as required to keep oil level at cor rect height Gearcase oil should be changed ev ery 250 hours of operation or once a year which ever comes first Use 90 wt oil when changing or adding oil to the gearcase C ARM BEARING Monthly grease arm bearing through the grease fittings in the spider There are 3 fittings on 3 arm trowels and 4 fittings on 4 arm trowels Pump grease into each fitting until clean grease comes out of spider at either end thoroughly clean excess grease off from spider when all arms have been greased Use any grade 1 lithium base grease D THRUST BEARING Weekly grease with any grade 1 Lithium based grease to purge out any dirt or water Wipe off excess grease Yearly for bearing lubrication remove thrust bearing and clean thoroughly Inspect for damage and replace if necessary or repack with any grade 1 lithium based grease and reinstall Refer to Spider Assembly Removal section in your Parts Service Trowel Manual P N 56354 for spider removal 19 CALIFORNIA PROPOSITION 65 WARNING Operation of this equipment and or engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Sfone Bred Tough Technology Born to Work The Way It Ought To Be Stone Construction Equipment Inc P O Box 150 Honeoye New York 14471 Phone 800 888
22. x 150 Honeoye New York 14471 Phone 800 888 9926 Fax 716 229 2363 TT a p k b E ud mie ds i fes d UD E e The Manufacturer warrants that products manufactured shall be free from defects in material and workmanship that develop under normal use for a period of 90 days for concrete vibrators and electric pumps one year for Rhino Bulldog Wolfpac Rollers trowels Stompers saws forward plates engine powered pumps and 6 months for all other products from the date of shipment The foregoing shall be the exclusive remedy of the buyer and the exclusive liability of the Manufacturer Our warranty excludes normal replaceable wear items i e gaskets wear plates seals O rings V belts drive chains clutches etc Any equipment part or product which is furnished by the Manufacturer but manufactured by another bears only the warranty given by such other manufacturer The Manufacturer extends the warranty period to Lifetime for the drum bearings and seals for the mortar mixers and agrees to furnish free of charge the bearings and seals only upon receipt of the defective parts The warranty is two years for eccentric bearings on the forward plate compactors mortar and plaster mixer drums trowel gearboxes and five years on the Bulldog trench roller eccentric bearings A Warranty Evaluation Form must accompany all defective parts Warranty is voided by product abuse alterations and use of equip

Operations

Contents

Download Pdf Manuals

Related Search

Related Contents