IR illuminator (AI-101) Quick Installation Guide 2012/04/05
Contents
1. 86 2 82455282 F 886 2 82455532 E sales vivotek com IR illuminator Al 101 Quick Installation Guide 2012 04 05 Note a There is only one DO connector on this Network Camera If the external IR illuminator is used no other DO devices can be connected o gt Baa Re TRG See When you check the Turn on external IR BA Click Yes to enable the IR illuminator Please note however all events about DO trigger in the Event Settings Event Setting will be cleared after enabling Name Status Sun Mon Tue Wed Thu Fri Sat Time i illuminator option a warning message will appear DI and DO Digital input The active state is Low the current state detected is High Digital output The active state is the current state detected is Grounded Once you enable the IR illuminator the Digital output option on the System page will be disabled currently b4 T _ Once you enable the IR illuminator the Digital au iw met output option on the homepage will be disabled Video Stream 1 v PTZ Panel Digita w x If DO function is needed please uncheck the _ Turn on external IR illuminator in night mode option in the Day Night settings Then the DO function aE can be used again V1 02. IR illuminator Al 101 Quick Installation Guide 2012 04 05 1 Product Introduction Package Contents A IR illuminator Al 101 1 pcs including stand plate and power plug B Screw 2 pcs X You should purchase power cable suitable for your local plug with enough cable length as shown on the right 7 SC Step 1 a Take Network Camera including the stand b Attach the Al 101 including locking screws to the side of the Network Camera Step 2 a As shown on the left loosen the fixing screws of the stand and the Network Camera Open the Network Camera V1 0 IR illuminator Al ae Quick Installation Guide 2012 04 05 Step 3 a Loosen the fixing screw of the stand A as shown on the left Adjust the angle and lean the stand joint forward to its maximum Pass the Al 101 control cable and power cable into the opening of the stand as shown on the left ai 4 Pass the power cable through the bottom of the stand A as shown on the left Pass the control cable to the opening of the stand B as shown on the left Step 5 a As shown on the left take the components of the waterproof connector from the Network Camera stand pack ttm s e z 7 7 s F f a F V1 0 viv IP Surveillance Wil IVOT sK 6F No 192 Lien Cheng Rd Chung Ho Taipei County Taiwan T 886 2 82455282 F 886 2 82455532 E sales vivotek com IR illumina
3. t the control cable as shown in the General I O Terminal Block section of the User s Manual xX Blue Connect Blue Ctrl to Ground X Red Connect Red Ctrl to Digital Output Step 13 a Secure the back cover of the Network Camera X Make sure that the cables are not jammed when you screw the back cover Step 14 a Connect the power cable you bought to the adapter of the IR illuminator Black L aa ED G Yellow E oy a To external power source White N ow X The cable should be connected based on polarity V1 0 Pe viverk IP Surveillance WWW VIVO Te KX lt com 6F No 192 Lien Cheng Rd Chung Ho Taipei County Taiwan T 886 2 82455282 F 886 2 82455532 E sales vivotek com IR illuminator Al 101 Quick Installation Guide 2012 04 05 Step 15 a Once you complete the steps above attach the camera to the stand plate and fix it on the wall as shown on the left Step 1 a As shown in the QIG User s Manual log on to the homepage Enter Configuration then click Advanced mode Enter Audio and video setting page Unfold Day Night settings check Turn on built in IR illuminator in night mode C Turn on external IR iluminator in night mode and save the setting then in the night mode the Al 101 should be activated V1 0 amp VIVO TeK Qs WWW VvIiVvoTreX lt com 6F No 192 Lien Cheng Rd Chung Ho Taipei County Taiwan T 8
4. tor Al 101 Quick Installation Guide 2012 04 05 Step 6 a Open the waterproof connector seal of the Network Camera b Secure the bottom of the waterproof connector seal X Make sure that the waterproof connector to the Network Camera is secured tightly Step 7 a Pass the control cable through the components of the waterproof connector one by one Step 8 a Pass the control cable into the bottom of the Network Camera V1 0 IR illuminato J r Al 101 Quick Installation Guide 2012 04 05 misi Step 9 a N Ma a Tuck the remaining part of the control cable into the case as much as possible X The back cover of the Network Camera can be opened so that control cable can be pulled out Step 8 a Secure the waterproof connector tightly X Make sure that the waterproof connector to the Network Camera is secured tightly Step 10 a Secure the waterproof connector completely b Attach the Network Camera body to the stand as indicated by the arrow mark X Make sure that the waterproof connector is secured tightly V1 0 viv IP Surveillance Wl Lu IVOT K 6F No 192 Lien Cheng Rd Chung Ho Taipei County Taiwan T 886 2 82455282 F 886 2 82455532 E sales vivotek com IR illuminator Al 101 Quick Installation Guide 2012 04 05 2 Step 11 a Secure the fixing screws of the stand and the Network Camera tightly Open the back cover of the camera Step 12 Connec
Download Pdf Manuals
Related Search