NPD5500 Navigation Unit Owner`s Manual
Contents
1. NAVIGATION Address book see also Address book chapter If the desired destination address is already in the address book or if it is among the 20 most recently entered destinations it can be easily accessed as a destination address Inthe Navigation menu select the function Address book and press OK Select Retrieve address and press OK Select the address book category e g using Prev destinations for the destination memory of the 20 most recent destinations Press OK Select the desired list entry Press OK Selecting Quit in the list or pressing the left cursor key 4 allows you to leave the list display without accepting a list entry Destination entry via map You can enter a destination via the Destination entry map by the following means e Cursors e Coordinates Cursors If the destination is not near the vehicle s position first enter the destination as accurately as possible using the keyboard see Direct address input Inthe Navigation menu select the option Destination map press a cursor key if you are already on the map display The destination entry map is displayed with cursors If no destination data were entered the cursors show the current vehicle position Using the cursor keys A v 4 gt you can now move the cursor Press OK select Store and press OK again so that the system will accept the position as the destination2. t First select a large scale for a rough determination of the destination Then select a smaller scale to mark your exact destination with the cursors Destinations in non digitized areas are also selectable When positioning the destination on interstate highways make sure you select the lane for the correct direction 24 NAVIGATION Co ordinates Select Destination map from the Navigation menu The map appears on the screen with cursors Press OK Select Co ordinates and press OK 4 Select Longitude or Latitude and press OK Next determine each digit using the remote control cursor keys A y lt gt and confirm the selection with the OK button If you wish to skip a digit press OK Select Set co ordinates and press OK To start navigation press OK select Cancel then Guidance and press OK again Via points Stops If you wish to visit other locations on route to the entered destination address you may store them as via points The navigation system then plans the route to include the via points in the given sequence before the destination address is reached Once a via point has been passed it is automatically deleted from the list You can store a maximum of 25 via points In the Navigation menu select the option Via points Press OK Enter the via points in the same manner as destination addresses see sections above Press Cancel
3. to return to the Navigation menu Storing a via point Select Store via point and press OK Deleting via points Select Delete a via point and press OK A list of the stored via points appears Select the via point you wish to delete and press OK A pop up menu appears displaying the selected entry Select Delete and press OK if you wish to delete the via point from memory Select Return and press OK if you do not wish to delete it The list of the stored via points reappears 25 NAVIGATION If the memory already contains 25 via points you will see a message that there is no room for additional via points Press OK If you want to enter a new via point you need to delete a previously stored via point t If all via points are to be deleted you can delete the destination including all via points in the Navigation menu Stopping guidance If you are currently on one of the guidance screens you can stop guidance at any time 0 Press OK select the Stop guidance option and press OK again Screen displays When guidance is active you can switch between the various guidance screens by pressing the NAVIGATION key on the RC 5400 or the MAP key on the RC 5000 Guidance display Once Guidance is activated the system will plan the route This may take some time depending on the complexity of the route In the meantime the first guidance message will be shown as guidance disp
4. which you can use to toggle between navigation and 16 GENERAL INFORMATION multimedia operation For the operation see the user s manual for the multimedia box and the TV tuner Select Return and press OK If the rear view camera is correctly connected and the setting Rear view camera connected is selected the image from the rear view camera is automatically displayed when the transmission is shifted into reverse Volume The following options may be selected in the Volume menu e SDVC To select a value for the speed dependent volume increase Find the SDVC value best suited for your vehicle by experimenting e Volume e Audible info On or OFF switches the volume off and on In the Settings menu select Volume Press OK Select the function to be set and press OK Select the desired value or the function to be set and press OK The Volume is set using cursor keys 4 and P on the remote control and pressing OK Pressing OK at Audible info On or OFF will toggle between on and off Select Return and press OK to confirm the selections System information The System information menu offers the following functions e Diagnosis For diagnosing hardware and software problems code protected only for authorized service personnel e Default settings Resetting the parameters of the Settings menu to the factory presets see the next paragraph
5. press OK This mode of entry is only useful for less common street names If you enter a common street name the cursor automatically jumps to Quit In this case enter the town first If there is a reasonable number of towns with this street the cursor jumps to List Select the desired town and press OK Select Guidance Press OK Travel icons The icons for the special destinations and points of interest destination categories are as follows Icon Meaning Icon Meaning Pharmacy L Marina Exhibition center E Movie theater de Automobile club hi Place of worship a Car rental n Clinic F Car repair shops H Hospital gt Railroad station r Cultural center Bank a Military installation 22 NAVIGATION Icon Meaning Icon Meaning a Governmental facility E Museum Library En P R pa Education ah Park m Embassy P Parking oma Bus station a Police Monument Ed Postal service A Shopping center 3 Service area 8 Ferry x Restaurant amp Fire station isi Tourist attraction Airport Sports facilities i Tourist information City center a ATM Gas station ft Civic center Theater T Hall of justice i Entertainment b Golf course Amusement park Hotel Destination r Industrial zone 23
6. to add a name it must be loaded from the address book edited and then re saved in the address book 29 NAVIGATION Retrieving a previous address from memory Select Address book in the Navigation menu Press OK Select Retrieve address Press OK Select Prev destinations Press OK A list of the last 20 destinations appears Select the desired entry and confirm with the OK button Deleting previous destinations from memory Select Address book in the Navigation menu Press OK Select Delete address and press OK Select Prev destinations and press OK To avoid inadvertent deletions you will be asked for another confirmation Press OK 30 USEFUL EXTRAS Trip computer You can call up the computer by selecting the function Trip computer from the Start menu The integrated on board computer shows the following information e Speed Current speed e Average speed Average speed since last reset e Elapsed distance Route distance since last reset e Elapsed time Travel time since last reset e Speed warning at Speed warning on off and warning limit adjustable The display of the speed is only informational The actual speed should be determined from the vehicle s speedometer only Use the function Reset to set the data for route distance time traveled and average speed back to 0 Speed warning When speed warning is activat
7. Settings menu and press OK Choose one of the three options and press OK see also the Screen function Language Selection of language for voice messages and menu texts on the screen Currently the system software CD contains the following languages with a selection of male and female speakers e British English e US English e French e German e Dutch e Italian e Spanish e Danish e Swedish GENERAL INFORMATION Two languages can be selected simultaneously for the system If necessary other languages can be loaded from the CD DVD In the Settings menu select Language Press OK Select Other language in the displayed list and press OK Select the desired language and press OK Select Load and press OK Press ESC or OK at Quit to return to the previous menu if you do not want to change the language Route criterion You can choose from several criteria for the route calculation e Fast suitable for all situations e Short recommended for city travel e Main roads recommended if you prefer to travel via highways e No main roads recommended if you prefer to avoid highways e Minimize toll roads The symbol for the selected route criterion appears in the status line To set change Route criterion Select Route criterion in the Settings menu and press OK The Route criterion list appears Select the desired route criterion and confirm with
8. They contain important information about the safe use of your device Failure to observe this information may result in damage or injury There fore please observe this information with particular care Denotes an action to be taken t Here you receive useful tips and information about the use of the system Terms in quotation marks refer to screen menu options For your safety The use of the navigation system by no means relieves the driver of his her responsibilities Traffic regulations and current traffic conditions must always be observed They will always have precedence over the advice from the navigation system if the current traffic situation contradicts the navigation system instructions The system does not take into account the relative safety of the suggested routes Closed roads construction sites height or weight restrictions traffic or weather conditions or other factors influencing the safety or travel time of the route will not be considered for the suggested routes Check the suitability of the suggested routes yourself Use the Alternate route function to receive better route suggestions or simply take the preferred route and leave the planning of the new route to automatic route re calculation For reasons of traffic safety make any entries to the navigation system before you depart or when the vehicle is standing In certain areas one way streets turning and entry prohibitions e g pedestri
9. e Configuration Software and hardware data for service purposes e Speed correction for setting the average speed used as the base for calculating the estimated time of arrival and the remaining travel time In the Settings menu select System information Press OK 4 Select Speed correction and press OK Press cursor keys 4 and gt to correct the speed and press OK Select Return and press OK to confirm the settings GENERAL INFORMATION Default settings This function allows you to reset all parameters to their factory presets In the Settings menu select System information Press OK Select Default settings and press OK Select Yes or No and press OK Settings for Factory preset Time zone 0 Clock format 12 hour format Date format month day year Units of measurement miles feet Voice messages On Volume mid level 0 SDVC Off Day color setting Blue Night color setting Dark blue Map color Automatic switching Map mode Northwards rolling activated Status line left Remaining travel time Status line right Estimated time of arrival Road type route criterion Fastest Avoid toll roads Deactivated Traffic info Deactivated Re routing level Middle 18 GENERAL INFORMATION Settings for Factory preset Delay time Low
10. e 1 03h Of g7 O e 1 11 PH After entering the postal code you can call up all town sections with the same code in List Select the desired town and confirm your selection with OK The town name also will suffice as destination input In this case the navigation system will guide you to the town limits Entering the postal code and town name will make it a unique entry 20 NAVIGATION List function If there are several towns or streets by the same name the List function will automatically display all choices with additional information Select the desired town or street using curser keys and press OK The list of all suitable names can be called up at any time using the List function If no character is entered the list starts with the first entry in alphabetical order You can select the desired entry from the list Selecting Quit in the list or pressing cursor key ESC or lt allows you to leave the list display without accepting a list entry Special destinations From the menu Special destinations you can enter the following e Points of interest Interesting and or useful locations their addresses are already contained on the DVD CD Examples Gas stations repair shops hospitals airports etc e Intersections if town and street have already been entered e All streets when available Input of street name without entering the town Quick Access useful for unique street names Po
11. ft 100 ft Return Seale Nap mode Info Stop guidance e 1 04 PH e 1 00h os KF FO List screen With certain selections a list appears in the right side of the display If not all list entries can be displayed you can scroll through them with the cursor e g by continuing to press cursor key w after reaching the bottom of the list Scroll up by continuing to press cursor key 4 once you reach Quit If additional information is available for an item in the list a gt appears to the right of the item To view this information press cursor key gt To make a selection move curser to the entry and press OK Press cursor key or ESC to leave the menu without selecting an option Settings adjusting the navigation system You can customize the navigation system to your specifications by changing many settings The following functions are available in the Settings menu which is accessible from the Start menu 12 GENERAL INFORMATION e Day night color e Language e Route criterion e Screen config e Measuring units e Remote control e Dynamic route e Traffic inform e Favourite function e Video configuration e Volume Day night colors Selecting the options e Automatic switching between day and night colors The night color is selected when the vehicle s headlights are turned on e Always day colors e Always night colors Select Day Night Color in the
12. route for a selectable distance Use this function if you want to avoid a traffic jam for example or if you disagree with the current route plan The alternate route will be calculated for the indicated distance from the current vehicle position Press the VOICE ALT R key longer than one second Now the system will show the Distance for which an alternate route should be planned The distance can be set from 1 to 6 miles Select the value after Distance and press OK 4 Set the value with the cursor keys A w 4 and gt Press OK Select the desired function and press OK Use Cancel or press ESC to return to the Start menu Info menu You can select the Info menu from the Start menu as well as from all guidance displays When you are on the guidance display Press OK if you are on one of the navigation screens Select Info and press OK If you are in the Start menu select Info and press OK The following choices are available e Message selection e Route criterion see the Settings chapter e Route list List of roads on the planned route e Points of interest To call up the list of special destinations in the vicinity of the vehicle location see Travel info and Points of interest in the Start menu e Via points Display of the next via point in the list of via points 28 NAVIGATION Address book The navigation system offers the opportunity of storing at le
13. seconds to initialize GENERAL INFORMATION C IQ Your key to map and travel information You received a DVD CD with current map and other travel information with your system In some countries the information on the CD is encrypted and is activated for a defined time partially or completely on demand with an access key Advantages for you e You pay only for information that you actually use e You pay only for the time you need it e After the initial activation you will automatically receive successive DVD CD releases e You will always have the latest information e Activation is easily obtained via the internet or over the telephone Navi ID BX5K HF57 DYD USA 2003 4 Code input Configuration My C I0Q Info Preview C I Service Return e h ve MSO Do Activation options The DVD CD contains all regionally collected road data Wherever available they offer travel information such as Destinations You can have individual states and individual guides activated for a certain period of time see also the preview in this chapter Your C IQ service will be happy to inform you about the available activation options see also C IQ Service in this chapter Reading the Navi ID Please have your Navi ID and the software code ready when contacting service Reading the identification In the start menu select C IQ and press OK Read the 8 digit code next to Navi ID To the right of this code yo
14. services police fire department etc do not rely solely on the navigation system There is no guarantee that all available emergency services in your vicinity are stored in the data base In such a situation you must rely on your own judgment and capabilities to secure help Maintenance and care To clean the system do not use cleaning gasoline alcohol or other solvents A moistened cloth would be best suited Functions of your navigation system The Multi Media System you purchased is a high performance instrument for the support of the driver in daily traffic Simply enter your destination before your departure activate Guidance and then drive off The navigation system provides you with visual and acoustic driving information The system is easy to operate with few control elements and a clearly structured menu System expansion In connection with a TMC expansion where available the system will show you the current traffic situation on your route and will guide you around traffic problems Numerous system expansions permit extending the system into an information and entertainment system GENERAL INFORMATION Distance indications On main highways the system s distance indications to exits may deviate from the indications on the road signs The signs on main highways measure the distance to the beginning of the exit while the system always calculates the distance to the end of the deceleration lane This is equi
15. 100 ft Your current position is New York 73 58 54 West 40 46 04 North ft Settings Return e 1 03h Cf SFO e 1 21 PH Inthe Emergency menu select the function Setting and press OK Enter the telephone number you want to store for the roadside service Confirm each number you enter using the OK button The number you entered will now appear in the Emergency menu 32 TROUBLESHOOTING On rare occasions your multimedia system may not function as you expect Before calling for service please read the operating instructions and go through the following check list it may be possible to easily remedy an apparent malfunction Symptoms Possible cause remedy System does not start screen dark Ignition is off please turn vehicle ignition on Ignition is already on system is in stand by Press one of the cursor keys the OK or the menu button on the remote control After a period of time the system turns itself off Under extremely low or high temperatures the system is turned off to protect it from damage It will turn itself as soon as the temperature returns to normal Monitor turns off at high temperatures At temperatures above 167 degrees Fahrenheit the monitor is turned off for protection It will turn itself on as soon as the temperature returns to normal After the ignition is turned off the last menu display remains in the monitor The monitor can re
16. Ensure that the GPS antenna is not covered by any objects DVD CD is automatically ejected by the navigation system The DVD CD may be soiled Clean with a special DVD CD cleaning fluid Time shown on the status line is incorrect Set the correct time zone in the Settings menu function Date Time Verify that you are not displaying ETA Address cannot be stored in the address book Address book is full Delete one or more entries that are no longer required Guidance is not accurate An inaccuracy of approx 150 feet is within the tolerance limits Please contact an authorized dealer if greater inaccuracies occur repeatedly Displayed position does not correspond to actual vehicle position GPS reception is interrupted for too long Once GPS reception is sufficient the position will be corrected automatically If necessary wait for several minutes Have your service shop check whether the navigation computer s installation angle was entered correctly in the diagnostics menu 34 USA TROUBLESHOOTING Symptoms Possible cause remedy Directions do not correspond to the actual traffic conditions It is possible that the car position calculated by the navigation system is incorrect at this instant The routing may have been changed and does not correspond with the information stored on the map DVD CD The system reports Incorrect o
17. NPD5500 Navigation Unit Owner s Manual PAGE 2 PAGE 36 P gina 72 TABLE OF CONTENTS GENERAL INFORMATION Explanation of symbols 4 For your safety ae she RA ar RRA A Be Wa eee A 4 Maintenance and care s sss st tt ttt es 5 Functions of your navigation system 5 System expansion 5 Distance indications a 3 6 eee eee eae eae 6 GPS reception AO a See he Se hs UR Se ae BS Av wept aid E ees S 6 Start up characteristics Sie fee fap cd said Sat Sab ew Bae em eae Be ai Ay ae 6 Automatic route re calculation 6 Areas with limited road information tt 6 Switching on off 0 6 Remote control gt gt sss o o 7 Stand by A A Br Sav GOD pal gig Vey eh at ede SS ee Se n ae ok 8 Inserting changing the map DVD CD sess 8 C IQ Your key to map and travel information 9 Activation options A E a ee Ge s l s 9 Reading the Navi ID 28 4 2 3S ech e a ee de 9 Entering the activation code 2 10 My HQ e 10 Preview Bs Be Sime he ae eR la ad aS GI de A ke ee IS 11 Configuration hoe Fo eee aoe E oe BR eo ew dee dw ale do ew 11 C IQ Service e ee 11 Screen menu types DI a a Ga ee Ea a AA G a 11 Pop up M nu e aoe e a ae a e a A 12 Pull down menu functions list se ete 12 List screen
18. Speed correction 100 Video configuration Multimedia box deactivated TV tuner deactivated Rear view camera deactivated Remote control RC 5400 NAVIGATION Destination input The following destination inputs are possible e Direct address input including postal codes Quick Access QXS and list e Input of special destinations e Copy from the address book e From the destination input map e Input of co ordinates Copy from special destinations e g points of interest Direct address input In the Start menu select the Navigation option Press OK Using your keyboard enter the destination address in State Town Postal Code and if applicable Road Special destinations or house No Confirm the input of each character by pressing OK Name and Telephone can be entered when the destination is to be saved in the adress book See Address book chapter To enter a space select Space and confirm with the OK button You can delete the last character entered using Delete and the complete line using Quit Character sequences for which no names are available are not selectable When you enter a unique character sequence your input is automatically completed Navigation 100 ft Nex Jersey Name Asbury Park Nj Monmout Road _ No Special destinations Phone ABCDEFGHIJKLMNOP RSTUVW Y 12345678 List Quit
19. an zones are not recorded The navigation system issues a warning in such areas Pay particular attention to one way streets turning and entry restrictions Please ensure that any person who may use your multimedia system has access to this user s manual and reads the guidelines and recommendations for the use of the system prior to first use GENERAL INFORMATION If your monitor is mounted on a flexible mount adjust it in such a manner that you can glance at the screen quickly and simply and avoid reflections and glare Stop at a suitable place before making any adjustments If your monitor is mounted on a fixed mount check if your dealer installed it according to the recommendations above The monitor should not be installed in any location where it might impede the view of elements required for the safe operation of the vehicle e g road mirror instrumentation vehicle surroundings Also the monitor must not be installed within the airbag inflation zone Only glance at the screen if this is possible without danger If you need to look at the screen for an extended time please pull over at a suitable location Always store the remote control at a safe location The values for current speed travel time and distance traveled displayed by the on board computer are calculated Precision cannot be guaranteed in all cases For the current speed the vehicle speedometer is considered accurate If you are looking for emergency
20. ast 200 destination addresses in a personal address book The address book is divided into Home Work Private and Business with Home and Work containing one address each for quick access Storing addresses After entering an address in the navigation menu select Address book and press OK Select Store address and confirm with OK Select the category for the address book and confirm your selection with OK The displayed address is now stored The home and work addresses can be retrieved by pressing the Home key lt 1 second home or gt 1 second work If the address memory is full one or more addresses that are no longer needed must be deleted before new ones can be entered Deleting addresses Select Address book in the Navigation menu Press OK Select Retrieve address and confirm with OK If you want to delete an address entry select the function Delete address Select the desired address book category A list with the names of stored addresses appears Select the desired address and press OK The selected address is now deleted or displayed in the Address book menu where it can be changed and saved again Storing the vehicle position in the address book Select Address book in the Navigation menu Press OK Select Store current loc and press OK Select the address book category Press OK t To edit an address e g
21. ed and the set speed limit is exceeded there will be an acoustic warning beep and a warning message on the display To set the speed limit Move the cursor to the field with the speed setting and press OK Use the cursor keys A y 4 gt to set the warning threshold then press OK To turn it on or off select Warning on off press the OK button The current status on off is indicated by the color of the square in front of the speed value red off green on Each time the OK button is pressed the speed warning is toggled on or off t The speed warning can be used to set the maximum speed when winter tires are in use 31 USEFUL EXTRAS Emergency The emergency menu contains the current vehicle position the country specific emergency number under Help and a programmable number for emergency roadside services The display accuracy for the car position is within about 100 feet The state the name of the town and the name of the street of the current vehicle position will only be displayed if the vehicle is on a digitized street If not or if there is no map DVD CD or the wrong map DVD CD in the navigation system only the geographic position as calculated by the GPS system will be displayed in longitude and latitude Entering a roadside assistance number In the emergency menu you can store any telephone number e g for an automobile club or for a roadside emergency service amp Emergency
22. g on off The multimedia system is turned on and off with the ignition If the system was not switched to stand by a title screen will appear first A message about the use of the system follows Confirm your selection by pressing the OK key After several seconds the system will be functioning All adjustments to the system setting will be saved upon switching it off GENERAL INFORMATION Remote control It will be necessary to change the remote control batteries when you use the remote control away from its holder and the navigation system no longer reacts to the push of keys or if the battery symbol appears on the screen status line To continue the use of the system push the remote control into the holder as the batteries are not needed there Some keys on the remote control have a double function which can be activated by pressing the key briefly under one second or more than a second RC 5400 FAVOURITE The key can be freely programed to accomomate specific functions see also chapter settings ENTERTAIN Press the key lt 1 second to switch to the last ertertainment source in use Press the key gt 1 second to go directly to the Info Menu NAVIGATION Press the key lt 1 second to switch between the routing displays Press the key gt 1 second to go directly to the Start Menu Acoustic message volume control Curser keys as well as OK confirmation key VOICE ALT R Press the key lt 1 second to
23. he number of days default is 10 days Press OK Press ESC or OK at Return to get to the previous menu C IQ Service This is where you will find the contact information for your C IQ service Select C IO Service in the C 1Q menu Press OK Press ESC or OK at OK to return to the previous menu Screen menu types The system uses three types of menus the pop up pull down and the list menu You can determine the current cursor position by the arrows to the left and right of the function to be selected Basically selectable functions are shown in bold print Any non selectable functions are grayed out and will be skipped by the cursor To select a function move the cursor to the desired option function using cursor keys A v 4 gt and press OK GENERAL INFORMATION Pop up menu Once a function is selected a pop up menu with additional selections may appear Press cursor key 4 to leave the pop up menu without selecting an option or function return Navigation New Jersey Name Asbury Park Nj Monmout Atlantic Ave No Special destinations Phone Address book Guidance Via points Destination map Route criterion Return e h 0 9 0 8 si se Pull down menu functions list In guidance mode Function appears on the display If you press OK the available functions are displayed If you do not select a function the menu will be closed again after several seconds Scale 400
24. ices you are presently using and how much longer they will be available to you Select Returned and press OK to receive information about previously activated products If you do not make a selection the system returns automatically to the previous menu after a short time 10 GENERAL INFORMATION Preview Your map and travel information software allows you to preview different products free of charge before ordering You can display the status of this preview Select Preview under C 1Q and press OK You will be shown the status of your preview choices It will contain a number of map and travel information products that you still can view free of charge Select Proceed and press OK to scroll to the next page Select C IO Service and press OK if you wish to establish contact Pressing ESC or OK at Back will take you to the C IQ main menu again Configuration Set your system to inform you automatically and in a timely fashion about the status of your activated products Select Configuration in the C lIQ menu and press OK Activate or deactivate Expiring soon and Starting soon by pressing OK Hide indicates that there will be no automatic announcements If you select Show you will always be kept current Set the number of days to be notified in advance to between 1 and 10 Select days and press OK Press the 4 and P keys to set t
25. ints of interest In the Navigation menu select the option Special destinations Press OK Select Points of interest Press OK Select as follows Close to car if your destination lies within the vicinity of the current vehicle location At destination if you want to go to an address at the destination you already entered National importance if you wish to select a destination of national or interstate importance 0 Press OK Select the desired category If necessary scroll through the display using cursor keys A and v in order to display the desired categories not visible on the screen Press OK Select the desired address Press OK Select Guidance Press OK t If travel to the final destination is to be interrupted such as a stop at the gas station enter the via point in Via points 21 NAVIGATION Intersection For longer destination streets it may be useful to enter an intersection In the Navigation menu enter the first street name and then select the option Special destinations Press OK Select Intersection Press OK 4 Enter the intersection using the keypad see Direct address input or from the list see Entry from List All streets Quick access Inthe Navigation menu select the option Special destinations Press OK Select All streets Press OK 4 Enter the street name see Direct address input
26. isplay modes an arrow indicating the linear direction replaces the guidance message Guidance in partially digitized areas In rural areas and smaller towns it is possible that not all roads are stored on the map DVD CD When you leave a digitized road the guidance screen display changes The display switches automatically from the guidance or split display to the map display Instead of the usual guidance message an arrow appears on the top right pointing in the direction of the destination Below the arrow the distance linear to the destination is displayed This can also happen in completely digitized areas as e g not all parking lots are digitized In such a case get your orientation from the map display Once you reach a digitized road you will see the usual guidance information next to the satellite icon 27 NAVIGATION Voice messages As soon as you activate guidance you will receive voice messages in addition to the symbols on the guidance screens If you miss a message Press the VOICE ALT R key on the remote control lt 1 second The last guidance message will be repeated or an updated guidance message will be issued When the symbol appears in the status line the voice messages are turned off You can turn them back on in the Settings menu as well as using the keys or on the remote control Planning an alternate route During guidance you can have the navigation system plan an alternate
27. l ec Gl Sp We cet as Yel Ven Ge sal Secs Se ves ON Aue 26 Screen displays ecb We cost aad Tel Lay sae Salis eke dade Se T L L B Vet A Be Lalas 26 Guidance display Boe BEV ay ee Me eC we Se ww eal RY wR AA 26 Map display Been GR Sah G2 k Gia np v s Bp cde 9 Tare RE See Rs Wy et Me idee he SO TP ae a od 27 Split display Dris BE Ge ie i oe es A Be a tO i Ges te as Ge ee ab 27 Guidance close to the destination tt 27 Guidance in partially digitized areas sees 27 Voice messages st a 28 Planning an alternate route 28 LAO ment a ve ra ic a E RA A a S n aa E 28 Address book e 063 os a a a e a e 29 Storing ddressse esta e ic a a A A a S l v M k 29 Deleting AO FESTA 2 al a O A AA u sar d Z 29 Storing the vehicle position in the address book 29 Retrieving a previous address from memory 30 Deleting previous destinations from memory 30 USEFUL EXTRAS Trip computer E BE sis ok t k ERS can er Wa GS ees ee Se 31 Speed warning gp oan Pay So tas oe eS a San lA aw a a Ge n l a 31 Emergency DA See CR ky Se ar Soe ar a aE Se RRA ce Oa E 32 Entering a roadside assistance number 32 TROUBLESHOOTING Troubleshooting E ate RAR A A A ARA 33 GENERAL INFORMATION Explanation of symbols The following symbols are used in this user manual This symbol denotes safety and warning notes
28. lay containing the following information Distance to destination or next via point Arrow linear direction to destination Menu name Distance to the next navigation instruction Name of next street on the route Travel direction indicator for the next intersection or junction Current vehicle position Name of street town and district if available on the map DVD CD Status line see also the Settings chapter 0000000 26 NAVIGATION Map display If guidance is active you can call up the map display by pressing the NAVIGATION key or MAP key or selecting Map in the Start menu O L scale 400 ft 100 Q i Fa 0 ELSA A 7 2 gt ri e a e P r 2 i mbe 1 03h OF SFO e 1 16 me Compass The arrow within the circle points north Change scale Distance to the next navigation instruction Simplified graphic display of the direction of travel the next intersection or junction Vehicle position arrow points in current direction of travel O Status line see also the Settings chapter 90060 Split display Accessed by pressing the NAVIGATION key The display unites the two display modes described earlier Guidance close to the destination If the entered destination is located off a digitized road guidance will continue to the point with the shortest linear distance to the destination The screen displays Destination is outside the digitized area In all guidance d
29. le Distance to the destination Geographical hight Current speed You can select one value for each statusline to be displayed Inthe Settings menu select Screen config Press OK Select the function to be set and press OK Select your choice and press OK The cursor will automatically return to the previous menu The navigation system uses an average travel speed for the calculation of the remaining travel time and the estimated time of arrival If necessary you can adjust this speed to your actual average speed using the option System information Speed correction Measuring units Selection of units of measurement for displaying and announcing distances and speeds The following options are available e Time format e Date format e Measuring units e Time zone e In the Settings menu select Measuring units Press OK e Select the function to be set Pressing OK will toggle between the available alternatives e At time zone press OK and curser keys w 4 to set the value up and down in half hour intervals Press OK again time is relative to GMT e Select Return and press OK to confirm the setting e Pressing ESC or curser key 4 will take you to the previous menu GENERAL INFORMATION Time zone Winter time Summer time EST 5 00 4 00 CST 6 00 5 00 MST 7 00 6 00 PST 8 00 7 00 Remote control There will be
30. lt lt ee 4 12 Settings adjusting the navigation system 13 Day night Olors 00 e a la e SE a 13 Language Dc e Ta aR A A ae de A AAA A HE ta a 13 Route criterion 14 Screen configuration a A GA ar a a k hy ah A 14 Measuring UNITS es Me Pa a Aa aa a eS 15 Remote control ess ee et ee 16 Dynamic FOUt 6 e ee aa e ADE AA A 16 Traffic information where available gt 16 Favourite function s e cm l m a a a aa a Av b a aa 16 Video configuration ie ia ia J Nab as be e co Ut BZ wae la Sa ah Be v r cay ee 16 Volume se e mas e ae a e a a a a oR ae Da A a Gaan a geok 0 17 System information gt o 17 Default settings E A NR AR a ake ca Abe 18 NAVIGATION Destination input Pie A E A E He ae v 20 Direct address input A OA e a a wade Se 20 LISTE function e dae e A AD a b 21 Special destinations o o eo 21 TABLE OF CONTENTS Points of interest 22 e oe eae a a de aa Rs 21 Intersection s gt a lt o lt lt ki a d a 22 All streets Quick access 22 Travel icons s r adr a 22 Address book see also Address book chapter 24 Destination entry via Map oros 24 Via points Stops fei E eR aR ke Ua a 25 Stopping guidance sc af Vel Len sawn te
31. main on for about 30 seconds after the ignition is turned off The system does not respond to keys pressed when the remote control is not in its holder Batteries are empty Change the batteries in the remote control or push it into the holder System reacts very slowly to entries or requires a long time for calculation You are in a very densely digitized area The system requires more time to read large quantities of data Guidance cannot be selected in the Navigation menu Verify that you entered a destination The system does not plan a route although a destination address was entered The vehicle is not on a digitized road Drive towards a digitized road 33 TROUBLESHOOTING Symptoms Possible cause remedy Guidance Check if Voice messages is activated in the information not Settings menu audible Check the Settings menu if Volume is not set to the minimum If no external speaker is connected Check the setting of the speaker volumes on the monitor or use on the remote control Some symbols depicted in the operator s manual do not appear on the status line Activate the appropriate entries for Status line right and Status line left under Settings in the Monitor setting menu The satellite symbol in the GPS logo is continuously red No satellite signals are being received
32. r defective media DVD CD possibly damaged DVD CD may not be C IQ capable DVD CD is not for this system System reports Incorrect code Code was entered incorrectly Code input needs to be repeated Code was incorrectly transmitted by C IQ service Contact the C IQ Service to obtain the correct code An identical code was entered and was either already activated or has expired Check your code in My C 1Q NAVIGATION key does not work or works only on the 500 mile scale The region or country may not be activated Contact C IQ Service System reports a System error Your system requires service Please contact the installer or your dealer If you should not find a solution for the problem turn to an authorized service 35
33. retrieve current acoustic routing information Press the key gt 1 second to plan an alternative route HOME If your home address is stored in the address book pressing the HOME key lt 1 second will directly retrieve your home address Pressing it gt 1 second your work address will appear if it is stored in the address bood ESC takes you to the previous menu 9000 GENERAL INFORMATION RC 5000 MAP Changing guidance screen displays or switching between menus and guidance displays MENU Calling up the start menu Setting the volume of voice messages Volume setting Cursor keys as well as OK confirmation key ALT R Planning an alternate route O REP Request current guidance advice 9900 Stand by You can switch the system into stand by from the start menu Select Stand by and press OK The screen is turned off the navigation voice messages will continue If you wish to first stop navigation press the OK key on one of the navigation screens Select Stop guidance and press OK Inserting changing the map DVD CD If the blue power LED is illuminated press the eject key on the navigation computer once with the ignition on e If the power LED does not illuminate press the eject key twice The system ejects the DVD CD Remove the DVD CD and insert the new map DVD CD carefully printed side up until it is pulled in After exchanging map DVDs CDs the system requires several
34. the OK key The symbol for the new route criterion appears in the status line Select Return and press OK Activate option Minimize tolls if you wish to avoid toll roads as much as possible The option Minimize tolls is only supported by related information on the map DVD CD Therefore the calculated route may still contain toll roads even with this option activated When the option t The Route criterion can also be changed in Route criterion in the Navigation menu Screen configuration Here you can select various color combinations for the screen display and configure the status line e Day color This setting is active when the headlights are off In bright daylight blue red and green offer the best contrast e Night color is active when the headlights are on At night dark blue dark red and dark green provide optimal readability e Map color offers various color combinations e Statusline left and Statusline right To select the information to be displayed in the bottom corners of the screen 14 GENERAL INFORMATION None Clock Date Remaining travel time The calculated remaining travel time to arrival at the next via point or the destination Remaining dynamic travel time where TMC is available Estimated time of arrival Estimated dynamic time of arrival where TMC is available Entire delay on route where TMC is availab
35. u will find the software number It will be useful to note both these codes on a piece of paper t You can also find the Navi ID in the Code Input menu under C IQ GENERAL INFORMATION Entering the activation code Once you receive your code enter it into the system In the Start menu activate C IQ followed by Code input Press OK each time Move the cursor to the desired characters or numbers confirming each selection by pressing the OK key Once the code is complete the cursor automatically moves to OK Press OK to accept The system will let you know if an incorrect code is entered and or if your system software is incapable of processing the encrypted information In such cases press either OK or C IQ Service if you wish to contact someone then press OK t The system can be used on a 500 miles scale without activation You may enter destinations however navigation information will be displayed only in activated areas and or for activated services My C IQ At any time you can find out about the activation status Select My C IQ below C IQ and press OK Select Active and confirm by pressing OK if you want to see details about your selected products Select Starting soon and confirm by pressing OK if you want to see details about software you ve already received Select Expiring soon and confirm by pressing OK if you want to find out which serv
36. valent to the point where the lanes separate GPS reception The system is capable of functioning even with poor GPS reception but the accuracy of the positioning may be limited Start up characteristics While a vehicle is parked for longer periods of time the satellites continue their orbit Therefore after turning on the ignition it may take several minutes until enough satellites can be received and evaluated Satisfactory reception three dimensional position is indicated by the green satellite icon on the screen If GPS reception is insufficient the satellite icon remains red During the start up sequence it is possible that the navigation system will announce Please proceed to the planned route The navigation system assumes that the vehicle is located away from a digitized road If other roads exist in this area the navigation system may issue incorrect messages The navigation system assumes that the vehicle is located on another road Automatic route re calculation If you ignore the system s announcements the system will automatically plan a new route Areas with limited road information In some areas not all of the information about a road is available on the map DVD CD Thus for example turning prohibitions information on the direction of travel in a one way street or prohibited entry into a pedestrian zone may be missing The navigation system will display a warning if you drive into such an area Switchin
37. various remote controls for your system Depending on the remote control to be used you need to activate it in Remote control Inthe Settings menu select Remote control Press OK Move the cursor to the desired option Press OK to toggle between activated and deactivated Select Return and press OK Dynamic route Pressing OK at Dynamic route will display the note that this function is not activated in the route criterion menu Traffic information where available Only relevant if dynamic route is activated in the Route criterion menu It allows the selection and deselection of traffic incidents to be displayed Favourite function The function key on the remote control can be programmed to call up certain functions Two options are available Pressing the function key less than a second and longer than a second Video configuration If a multi media box a TV tuner or a rear view camera is installed the appropriate option Multimedia box connected TV tuner connected or Rear view camera connected must be activated Switching options on off Inthe Settings menu select Video configuration Press OK Move the cursor to the desired option Press OK to toggle between activation and deactivation If the option Multimedia box connected TV tuner connected and or Rear view camera connected is activated the Start menu contains the function TV Video
Download Pdf Manuals
Related Search