Home

IL-GIOTTO1200S Manual - Techni-Lux

1. Giotto spot 1200 User s Manual rel 1 00 SGM LIGHT TECHNOLOGY Giotto spot rel 1 00 General instructions Read the instructions in this handbook carefully as they give important information regarding safety during installation use and maintenance Be sure to keep this instruction manual with the fixture in order to consult it in the future If the fixture is sold or given to another operator make certain he or she also receives the manual to be able to read about its operation and follow the relative instructions This fixture is not intended for home use After having removed the packaging check that the fixture is not damaged in any way If in doubt don t use it and contact an authorized SGM Technical Service Centre Packaging material plastic bags polystyrene foam nails etc must not be left within children s reach as it can be dangerous This fixture must only be operated by adults Do not allow children to tamper or play with it Electrical work necessary for installing the fixture must be carried out by a qualified electrician or experienced person Never use the fixture under the following conditions In places subject to excessive humidity In places subject to vibrations or bumps In places with a temperature of over 45 C or less than 2 C Protect the fixture from excessive dryness or humidity ideal conditions are between 35 and 80 Do not dismantle or modify
2. mind to avoid possible overlapping of other fixtures channels which would cause problems with the perfect control of all the available functions Should it be necessary it s possible to allocate the same start channel to several fixtures in this case the fixtures will all follow the same commands but can t be controlled separately To address fixtures correctly proceed as follows 1 Connect Giotto Spot to the power supply wait until it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the Addr menu Press ENTER to confirm The message on the display starts to flash Use the UP DOWN keys to select the channel required Press ENTER to confirm Start Start Start Start Address Address Address Address Or eoo 3 3 Direction of Pan movement This function allows to decide the direction in which the Giotto s moving head pans indispensable when several fixtures are installed in order that fixtures installed opposite each other move in the same direction when they receive a command To modify Pan movement proceed as follows 1 Connect the Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the Pmove menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select which of the two available options is required see table pag 15 Pres
3. 134 122 79 167 35 212 250 33 195 78 133 123 78 168 34 213 251 34 194 79 131 124 77 169 34 214 8 252 __33 32 __31 EM 122 ee 130 i coo NEN 33 NEM o NND 36 32 216 8 254 37 31 255 38 39 30 40 29 DM c ee 122 28 EN 182 eee 121 NEN 25 43 27 io 89 110 134 179 26 vs BONN 117 NNNM NNNM D e A eo co En A 25 29 Giotto spot rel 1 00 SIGIM LIGHT TECHNOLOGY SGM Elettronica srl Via Pio La Torre 1 61010 Tavullia PS Italy Tel 39 0721 476477 Fax 39 0721 476170 e mail info sgm it e http www sgm it
4. 16 bit Remote control of lamp ignition enabled Remo lamp ignition disabled DS Remo reset enabled Remote contro reset disabled 100 92 84 76 Possibility of slowing the maximum speed of PAN and TILT movement Default configuration 100 Fast 100 53 40 27 20 13 6 0 ptimizes speed performance Allows to regulate the brightness of the display Default configuration 40 Inverts the reading position of the display Used according to the position of the fixture Range 8 998 sec It s possible to decide for how many seconds the fixture s last status must be held when there s no DMX signal default 20sec it maintains always the last condition of job independently from how much time lacks the dmx Energy saving enabled Energy saving disabled Read only menu giving information on the software version supported by the fixture DD HD E 15 Giotto spot rel 1 00 Giotto spot rel 1 00 3 2 Allocating the first addressed channel In order to receive the commands necessary to operate from a lighting console each fixture has to be allocated a start address This address normally indicates the first channel used start channel and can be allocated following a different criterion from that used to connect the signal line Giotto Spot uses 18 controls channels so during allocation this quantity must be borne
5. 3 8 sec and 270 Tilt 2 4 sec 8 16 bit movement resolution Automatic repositioning in the event of accidental head movement invertible Pan Tilt movement Adjustable Pan Tilt offset Adjustable acceleration and speed parameters Electronic Ballast Supplied as standard with every fixture Automatic universal 90 245V 50 60Hz power supply Flicker free Reduction of lamp power in the event of fixture overheating Power Factor Correction Automatic energy saving if the beam is blacked out Automatic lamp re strike Optics High luminous efficiency optics 4 beam angles 9 12 15 and 18 Display Microcomputer Personalization of the fixture according to installations test functions for all effects enabling of remote lamp On Off via DMX enabling of fixture reset via DMX fixture addressing display flip function rotation through 180 dimmable display and more Display of data such as lamp elapsed time and number of strikes fixture operating time software version supported Control signal Input signal DMX 512 RS 232 Clamping system Fast Lock clamp supplied as standard Several mounting points for clamps enabling the fixture to be mounted on any type of truss Connection point for safety cable Giotto spot rel 1 00 Giotto spot rel 1 00 Accessories Light Dome for outdoor protection cod 0202406 Single flight case cod 0061741 Double flight case cod 0061744 O
6. to be obtained Changeover from one gobo to another can be done rapidly and directly or blacked out this function is controlled by chan nel 8 shutter strobe using the strobe shutter s Autoshade on Gobo function It s also possible to synchronize gobo changes with a musical bass beat in which case gobo selection is random and in any case not synchronized on the various fixtures The gobos on the rotary wheel can rotate both clockwise and counterclockwise and the position can be stored if required CENTRAL VALUE FUNCTION 2 _ 2 GOBO 1A 3B GOBO 3B 24 8 0 CHANNEL SHUTTER STROBE CH 8 The Shutter Strobe is controlled by Channel 8 The mechanism which enables the strobe effect to be generated is the same as that used for dimming the light beam however it s also possible to control the light s intensity while the strobe s enabled This ensures instant beam blackout without any light spill High impact visual effects such as the strobe effect running in sync with the bass beat and the light blackout during color and gobo changes can be enabled directly with this channel DMX VALUE CENTRAL VALUE FUNCTION EE a Strobe Frequency of S Hz Sttobe atarequencyof Hz Shutter strobe low strobe effect at maximum flash mms Om __________ 9 0 Dimmer ch 9 Controlled by Channel 9 enables linear control of light outp
7. used to avoid errors and differences between t he actual functions and those shown in the book Giotto spot rel 1 00 Giotto spot rel 1 00 I installation Before proceeding with fixture installation make certain that the packing contains all the items shown in the following list and ensure that the fixture is undamaged If in doubt don t use the fixture and contact an authorized SGM technical assistance centre and the freight company In fact only the recipient can claim for any damage caused to the fixture during transport Giotto spot 1200 Warranty Instruction Manual 1 Male XLR 5 P connector 1 Female XLR 5 P connector 1 Power con connector 2 Fast Lock clamps KEEP THE PACKING MATERIAL Packing material plastic bags polystyrene foam nails etc is potentially hazardous so must never be left within children s reach Use the original packing in the event of having to return the fixture to the manu facturer for repair or maintenance it s been designed specifically to protect the fixture during transport 1 1 Locking and unlocking the mechanism Giotto fixtures are fitted with a mechanical locking system for the moving parts The moving head and yoke must be locked every time the fixture is transported using the appropriate flightcase or the original packing which have an suitable shock proof support system Remember to ALWAYS unlock the mechanism BEFORE switching on the fixture The f
8. used to reset the meter On the contrary pressing the UP key restores the previous value Press ENTER to confirm the changes OV O1 S NS 3 7 Lamp strike meter The Giotto s microcomputer stores various data including those relative to the number of lamp strikes This information is important because needless lamp strikes causes stress to materials and components so can contri bute to reducing lamp life To know how many times a lamp has been ignited 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Use the UP DOWN keys to find the Lmp_st menu The number of lamp strikes will be displayed automa tically 3 71 Resetting the lamp strike meter Each time the fixture is relamped it s possible to reset the meter which counts the strikes in order to have num ber of actual strikes for the lamp about to be installed To reset the meter proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the Lmp_st menu Press ENTER to confirm The message on the display will start to flash The DOWN key can be used to reset the meter On the contrary pressing the UP key restores the previous value Press ENTER to confirm the modifications 3 8 Fixture operating time meter This function allo
9. 6 13 ELECTRONIC FOCUS CH 13 This channel gives smooth precise focus control obtaining clear projections at any distance or suggestive out of focus effects DMX 512 FUNCTION level Range 0 255 000 255 Linear Regulation 14 ADDITIONAL LENSES CH 14 By means of this channel it s possible to choose projection angle from those available see table It s thus possible to obtain wide angle projections at a short distance or long throw projections DMX VALUE CENTRAL VALUE FUNCTION i 7 N poo oo WTDewelem 000 __ __ 1 ___ 15 COLOR FILTERS CH 15 By means of this channel it s possible to select the two tone dichroic filters and the color conversion filters DAGCTO and 0461 It s possible to superimpose these filters with the 24 possible colors available thus obtaining two tone projections in various shades DMX VALUE CENTRAL VALUE FUNCTION Yellow Cyan dichroic filter Green Red dichroic filter DD CE Giotto spot rel 1 00 Giotto spot rel 1 00 16 FROST CH 16 Adjustable from channel 16 the linear regulation of the frost concurs DMX 512 FUNCTION level Range 0 255 0 NO Frost inserted 000 255 Linear Regulation 255 Frost inserted 1 7 MSPEED CH 17 Mspeed controls PAN and TILT and is intended as the time required to complete a movement from one position to another This means that fixtures with the same Mspeed value will reach thei
10. SB Operation Only this byte is sent Linear range 0 255 2 4 position wheel for 25 combination gobo wheel rotation music change The dimmer 15 partially electronic and Ch9 partially ee neal Linear range 0 255 Allows to insert one of the two S bl Prisms rotary prisms or neither See table ee table Ch13 ELE Allows to focus the image Linear range Linear range 0 255 Ch15 Conversion filters Effects See table See table Movement speed Controlled cross fade Slowest vel min Fastest vel max Mspeed See table 5 0 IRIS CHANNEL CH 5 Adjustable by channel 5 it allows the linear regulation of amplitude of the luminous bundle beam Peculiar characteristics of the diaphragm are the high speed of opening closing 100 mS and low noise MNIMALOPENNG 255 MAXIMUM OPENING 22 6 0 COLOR CHANNEL CH 6 Giotto Spot 1200 is fitted with an exclusive color generation system comprising 12 frames containing dichroic colour fil ters Color changes are controlled by Channel 6 allowing to select 24 different colors which combined with the two colour conversion filters produce 72 different tones As well as selecting the colour it s also possible to use some func tions with great visual impact such as running the colourchanger in sync with the music or continuous rotation of all the colours available at 3 different speeds rainbow effect By using the colour cha
11. Use the UP DOWN keys to select which of the two available options is required see table pag 15 5 Press ENTER to confirm 3 41 Limiting Tilt movement The Giotto fixture has a Tilt movement range of 270 3 4 of a revolution If the entire excursion doesn t have to be used two parameters allow to limit the starting angle TP min and ending angle TP max The only limit is the minimum difference between starting MIN and ending MAX which is 4 To limit the Tilt movement proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Usethe UP DOWN keys to find the TP min menu if the starting angle is to be modified If the ending angle is to be changed find the TP max menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select the new starting or ending angle 5 Press ENTER to confirm Pw DD C5 CD wm 7 Giotto spot rel 1 00 Giotto spot rel 1 00 3 5 Pan Tilt inversion This function also allows to optimize the movement of the Giotto s moving head in relation to the operator s position in order to simplify all positioning procedure When SWAP is enabled ON this means that the lighting console sends the data regarding Pan to the Tilt con trols and vice versa To invert PAN and TILT movement proceed as follows 1 Connect Giotto Spot to the power supply wait till it
12. al group in the fixture s moving head Follow these instructions when fitting or replacing the lamp 1 Disconnect the power supply and wear protective gloves and glasses 2 Remove the head s top cover 3 fig 1 Unscrew the two locking screws A on the aluminium support which fix the lampholder base to the optical group 4 fig 2 Raise the aluminium support and fit the lamp in the base Avoid touching the lamp bulb with your fingers Should this happen clean it before use with a soft cloth and alcohol then clean with a dry cloth 5 fig 3 Tighten the screws again making certain that the lamp wires are positioned in the appropriate slots 6 Close the cover again a Q fig 1 fig 2 fig 3 1 4 Lamp Alignment After each relamping it s important to align the lamp with the optical group in order to obtain maximum uniformity and light output 1 Fit the new lamp close the fixture and switch it on 2 Connect the fixture to a lighting console 3 Point the fixture at a flat surface if possible light coloured at a distance of at least 3metres 4 Set the control channels in such as way as to obtain the projection of a white beam Then IRIS open DIMMER at maximum luminosity suitable FOCUS no GOBO or COLOR projected 5 Fig 4 Loosen the two fastening screws A and use the knobs on the sides to align the lamp horizontally 6 Fig 5 Use the large centre brass ferrule to align the l
13. amp vertically with respect to the optical group 7 The lamp is aligned correctly when a uniform beam is obtained without any shadows or zones which are brighter than others 8 Fig 6 Tighten the fastening screws and close the cover again Giotto spot rel 1 00 Giotto spot rel 1 00 1 5 Power cable construction DANGER ELECTRICAL SHOCK HAZARD Electrical work necessary for installing the fixture must be carried out by a qualified electrician or an experienced person The fixture must be suitably earthed Failure to comply with this automatically invalidates the guarantee The POWER CON type connector supplied along with the Giotto is indispensable for connecting the fixture to the power supply The following design shows how to connect the connector to the cable whereas the table shows the symbols normally used to indicate connections When in doubt consult a qualified electrician CABLES PIN TYPICAL Brown Phase Yellow Copper Blue Neutral Silver Yellow Green Ground Green Conductors cross section TN Power supply Minimum cross section 230 V 3x1 5 iC 120V 3x2 5 Q i gt p p gt x ae 1 6 Giotto Spot s power suppl ATTENTION Don t power the Giotto with a dimmer circuit this could damage the electronic ballast Before connecting the fixture make certain that the data on the fixture s plate correspond with those
14. an select one of the brightness levels available for the Giotto display which can be standard or very low This option is intended for theatre and television use where excessive brightness can be troublesome To change display brightness proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Use the UP DOWN keys to find the Bright menu 3 Press ENTER to confirm The message on the display will start to flash 4 Use the UP DOWN keys to select the required option from those available 5 Press ENTER to confirm the modifications 3 14 Display reading position When the fixture is mounted upside down on a structure operators can turn the display through 180 thus greatly facilitating the reading of the menus on the display To change the reading position proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Use the UP DOWN keys to find the Dspl Flip menu 3 Press ENTER to confirm The message on the display will start to flash 4 Use the UP DOWN keys to select the required option 5 Press ENTER to confirm the modifications 3 15 Test functions Test programs can be used in the event of it being necessary to check the correct operation of the fixture or some of its parts To selection the required test program proceed as follo
15. e meter 3 9 Input signal 3 10 Pan Tilt resolution 11 Remote control of lamp ignition 12 Remote fixture reset 3 Display brightness 4 Display reading position 5 Test functions 6 Control of the acceleration of movement speed 7 DMX DLY 8 SLLF 3 19 Reserved functions 4 Giotto Spot 1200 control channels 5 Iris channel 5 6 Color channel CH6 7 Gobo channel CH7 8 Shutter Strobe channel CH8 9 Dimmer ch 9 24 0 Gobo rotation ch 10 1 Prisms ch 11 2 Prism Rotation ch 12 3 Electronic focus ch 13 4 Additional lenses ch 14 5 Color Filters ch 15 6 Frost ch 16 7 Mspeed ch 17 8 Lamp ignition and remote reset ch 18 WWW WWW CI CD Appendix Giotto spot rel 1 00 Giotto spot rel 1 00 Introduction Giotto Spot 1200 is an innovative professional SGM moving head fixture designed and built for use in large show events thea tres TV studios and entertainment venues in general The result of SGM s many years experience in mechanical and electronic design thanks to its avant garde performance Giotto Spot 1200 is one of the world s top fixtures The use of an MSR 1200SA discharge lamp and a perfect optical system in fact make it one of the best fixtures on the market today as far as power and luminosity are concerned The lamp and electronics are powered by an electronic ballast entirely designed b
16. has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the SWAP menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select which of the two available options is required see table pag 15 Press ENTER to confirm Qu ds gano 3 6 Lamp elapsed time meter The Giotto microcomputer stores various data including that relative to the number of hours the lamp is lit ela psed time This is necessary to know in advance when it s almost time for relamping lamp life is approximately 750 hours To see how many hours a lamp has been used proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Usethe UP DOWN keys to find the Lmp H menu The total number of hours the lamp has been lit will be displayed automatically 3 61 Resetting the lamp elapsed time meterad Each time a new lamp is fitted it s possible to reset the meter indicating the elapsed time in order to have the real elapsed time for the lamp about to be fitted To reset the elapsed time meter proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the Lmp H menu Press ENTER to confirm The message on the display will start to flash The DOWN key can be
17. ixture is locked and unlocked by turning the two knobs on the yoke following the printed indications DANGER high temperature avoid contact with persons and things 1 2 Access to the inside Giotto fixtures have a simple mechanism for opening the moving head To open the two covers just turn the two locking screws shown in the illustra tion through 180 then raise the cover Any work must ALWAYS by carried out by qualified technical personnel When work is finished close the covers again making certain that they are clo sed against the fixture body B b B i ATTENTION make sure that the fixture is off and the temperature of the parts can t cause burns wait for at least 30 minutes after switching off 1 3 Lamp installation ATTENTION This fixture is designed exclusively for use with Philips MSR 1200SA lamps NEVER USE ANY OTHER TYPES OF LAMPS Disconnect the power supply before carrying out any work on the fixture Make certain that the fixture is off and the temperature of the components can t cause burns wait at least 20 minutes after switching off gt Never carry out any work if the fixture doesn t have its protective covers its lenses are damaged Discharge lamps can explode Never look directly at the lamp when it s lit discharge lamps emit UV rays which are dangerous for sight There s an optic
18. lock the PAN and TILT locking system once the fixture is mounted on the support structure safety chain socket S 11 Giotto spot rel 1 00 Giotto spot rel 1 00 2 0 Construction of the signal cable Giotto 1200 has a DMX 512 input fitted with standard 5 pin XLR connectors Screened cables in compliance with EIA RS 485 specifications and the following characteristics must be used for connections 2 conductors plus screen 1200hm impedance low capacitance max transmission rate 250kBaud Cable connections see illustration taking care with the screen which must be connected to Pin 1 ATTENTION the screened parts of the cable sleeve must NEVER be connected to the system s earth as this would cause faulty fixture and controller operation Example of connection of the DMX line DMX linea DMX controller B Termination DMX dn last ap ooon B EICIEICICIEI CI DODODODOOOOOODOODDOUDOOUO Cl Ol lo To avoid the risk of faulty operation follow these indications Maximum cable length 500 metres Max N of fixtures connected 32 Cable runs Avoid running cables alongside power supply lines Termination A 120Ohm resistor between Pins 2 and on the last fixture 2 1 Construction of the DMX termina
19. nnel in combination with the strobe chan nel autoshade effect can be obtained which blacks out projection for a moment when colours are changed DMX VALUE CENTRAL VALUE FUNCTION 0 7 3 WHITE 8 14 11 PINK 15 21 18 MAGENTA 22 28 25 LAVENDER 29 35 32 BLU LIGHT 36 42 39 AZURE 42 49 46 CYAN 50 56 53 YELLOW 57 63 60 AMBER 64 70 67 FLAME RED 71 77 74 WOOD 78 84 81 PRIMARY RED 85 91 88 LIGHT GREEN 92 98 95 GREEN AZURE 99 105 102 GREEN AMBER 06 112 09 YELLOW GREEN 13 119 116 GREEN CYAN 20 126 23 GREEN YELLOW 27 133 130 DARK RED 34 140 37 LIGHT MEDIUM BLUE 41 147 144 GREEN 48 154 51 MEDIUM BLUE 55 161 158 MEDIUM RED 62 168 65 ORANGE 69 175 172 DARK PURPLE 76 182 79 RAINBOW SPEED 1 SLOW 86 189 186 RAINBOW SPEED 2 90 196 93 RAINBOW SPEED 3 97 203 200 RAINBOW SPEED 4 FAST 204 210 207 MUSIC CHANGE AT EACH BASS BEAT 211 217 214 MUSIC CHANGE EVERY TWO 2 BASS BEATS 218 224 221 MUSIC CHANGE EVERY 3 BASS BEATS 225 255 236 MUSIC CHANGE EVERY 4 BASS BEATS DD C5 CD wm Giotto spot rel 1 00 Giotto spot rel 1 00 7 0 GOBO CHANNEL CH 7 Gobo selection is controlled by Channel 7 The gobo group comprises two independent wheels each with four images and a blank position The gobos are interchangeable and superimposing the two wheels enables 25 different combinations
20. o Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN to find the DMXDLY menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select the required time Press ENTER to confirm changes 20 3 18 SLLF This is an energy saving function If the function is enabled SLLF ON the fixture reduces lamp power by dim ming it electronically after the shutter has been closed for 30 seconds Maximum power will automatically be restored as soon as the shutter is reopened To enable this function proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the SLLF menu Press Enter to confirm The message on the display will start to flash Use the UP DOWN keys to select the required option Press Enter to confirm changes porno 3 19 Reserved functions Some fixture functions can t be accessed by operators as they regard software sections as yet to be defined in this firmware release When RESERVED appears on the display you re in this section Access is forbidden DD C CE m Giotto spot rel 1 00 Giotto spot rel 1 00 4 0 GIOTTO SPOT 1200 CONTROL CHANNELS Pan High byte in 8 bit operation Chi Pan MSB Only this byte is sent Tilt High byte in 8 bit Tit M
21. of the local main power supply The fixture must be connected to a cut off circuit with the following characteristics Cut off circuit Power supply in id 230 V 16A 0 03A 120 V 32A 0 03A 1 7 Installing the fixture on a support structure Read the following safety information before proceeding with the installation of the fixture e Fixture not for domestic use Do not install the fixture near sources of heat nstall the fixture in a well ventilated place Avoid blocking air intakes and outputs Do not use the fixture In places subject to vibrations or bumps In places with excessive humidity In places subject to temperatures of more than 45 or less than 2 C e Protect the fixture from excessive humidity ideal values are between 35 and 80 Avoid inflammable liquids water or metallic objects entering the fixture Keep any inflammable material at a distance of at least 1 5m from the fixture Position the fixture at least 1 5m from the surface to be lit Don t lift the fixture holding it by the moving part the head 10 1 8 Positioning the fixture Can be installed in any position pee OK 1 9 Fitting clamps OK Always use two clamps to hang the fixture e Fix the fixture to the support structure using safety chains fitted to the 2 holes on the underside of the fixture s base Don t fix the safety chain to the handles Remember to un
22. ptional clamp unit cod 0202403 Technical specifications LAMP MSR 1200SA GY16 COLOR TEMPERATURE 6500K LIGHT OUTPUT 96000 LUMEN LIFE 500 HOURS POWER SUPPLY ELECTRONICS AND LAMP ARE POWERED BY A SWITCHING POWER SUPPLY THE FIXTURE CAN OPERATE AT ANY VOLTAGE BETWEEN 90V AND 240V 50Hz 60Hz POWER ABSORBED 1500W OPTICAL SYSTEM i NTERNAL OPTICAL GROUP COMPRISING HIGH LUMINOUS EFFICIENCY POLISHED REFLECTOR AND DOUBLE CONDENSER 4 BEAM ANGLES 9 12 15 189 ELECTRONIC FOCUS ELECTRONICS CS0276 INPUT SIGNAL CS0244 CS0245 ELECTRONIC BALLAST CS 0252 IGNITOR CS 0268 ELECTRONICS AND MOTOR DRIVER CONTROL CS0273 PAN TILT MOTOR DRIVER CONTROL SETTING VIA BUILT IN MICROCOMPUTER CONTROL SIGNAL USITT DMX 512 RS 232 DMX CONTROL CHANNELS 18 cH AUTOMATIC REPOSITIONING VIA OPTICAL SENSORS CONSTANTLY CONTROLLING PAN AND TILT POSITION AND CORRECTING IT IN THE EVENT OF THE MOVING HEAD BEING ACCIDENTALLY MOVED COOLING FORCED VENTILATION BY MEANS OF TWO LOW NOISE FANS WHOSE SPEED IS ELECTRONICALLY CONTROLLED ACCORDING TO CHANGES IN TEMPERATURE IN THE FIXTURE PROTECTION FUSES 2x16A CF 6 3 x 32 TYPE FUSES BODY SHEET METAL WITH POWDER PAINT FINISH AND EXTRUDED DIE CAST ALUMINIUM WITH POWDER PAINT FINISH DIMENSIONS HxLxD 77 53 47 5 WEIGHT Kg 30 SGM Elettronica reserves the right to improve or modify their products at any time without prior notice Always consult the handbook of the unit being
23. r destination at exactly the same moment It s therefore possible to set movement times for each fixture which are independent from the times sent by the lighting console DMX values between 000 003 allow the lighting console to control the movement whereas from DMX value 004 it s pos sible to allocate the movements a movement time To determine Mspeed time refer to the conversion table DMX VALUE FUNCTION 0 3 Controller cross fade 4 Slowest 255 Fastest 18 REMOTE LAMP IGNITION AND RESET Ch 18 The lamp can be switched on and off can be controlled via DMX by means of a lighting console In fact after the Giotto has been powered up the lamp will remain off until the lamp ignition command is sent This function has no effect if it s not enabled by means of the fixture s built in microcomputer In this case the lamp will ignite automatically without waiting to receive the command from the lighting console In the event of the lamp being switched off accidentally it s advisable to wait at least 5 minutes before sending the igni tion command Nevertheless if the command is sent earlier Giotto Spot carry out lamp ignition automatically carrying out restrike attempts at regular intervals of 3 minutes Lastly Giotto Spot 1200 has another function which automatically reduces the power of the lamp by 5096 every time the shutter or dimmer are closed This function ensures considerable improvement in fixture cooling and increa
24. r the display are for selecting and using the various submenus which make up the main menu UP DOWN keys used to scroll the various items in the menu In the selected menu used to change the required para meters ENTER key used to access to the selected menu and once the necessary changes have been made is used to confirm them CONTROL Menu Options Description Default configurations are shown in bold text Range 001 487 Addressing the fixture NORM Control of Pan inverted from right to left Range 000 540 Normal control of Pan from left to right Sets Pan starting angle Default Configuration 000 degrees Range 000 540 Range 000 540 Sets Pan ending angle Default Configuration 000 degrees NORM Normal control of Tilt from up to down REV Control of Tilt inverted from bottom to top Range 000 270 Range 000 270 Range 000 270 Set Tilt starting angle Default Configuration 000 degrees Range 000 270 Sets Tilt ending angle Default Configuration 000 degrees Pan is controlled by Tilt commands and vice versa Normal control of Pan and Tilt Read only menu Records the elapsed time of the lamp Can be reset Read only menu Records the number of lamp strikes Can be reset Read only menu Records total fixture operating time Signal RS 232 selected Allows to select movement resolution Default configuration
25. s ENTER to confirm Oh Qs 3 31 Setting Pan starting angle The Giotto fixture has a Pan movement range of 540 a revolution and a half If the entire excursion doesn t have to be used two parameters allow to set the starting angle PP_min and ending angle PP_max The only limit is the minimum difference between starting MIN and ending angle MAX which is 4 To limit Pan movement proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Use the UP DOWN keys to find the PP min menu if the starting angle has to be modified If the ending angle has to be modified find the PP max menu 3 Press ENTER to confirm The message on the display will start to flash 4 Use the UP DOWN keys to select the new starting or ending angle 5 Press ENTER to confirm 3 4 Direction of Tilt movement This function allows to decide the direction in which the Giotto s moving head tilts indispensable when several fixtures are installed in order that fixtures installed opposite each other move in the same direction when they receive a command To modify Tilt movement proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Use the UP DOWN keys to find the Tmove menu 3 Press ENTER to confirm The message on the display will start to flash 4
26. s valid to all effects only on presentation of the guarantee certificate to the manufacturer or the nearest SGM technical assistance centre e Always quote the unit s serial number and model when contacting your reseller for information or assistance Protect the environment don t throw packing material into your garbage can return it to your SGM retailer or take it to the nearest special waste collection point index A 10 10 11 11 12 12 13 14 14 16 17 17 17 17 18 18 18 18 18 19 19 19 19 19 20 20 20 20 20 21 21 22 22 23 24 25 25 26 25 26 27 27 27 28 28 28 Intruduction Main features Technical Specifications 1 0 Installation 1 1 Locking and unlocking the mechanism 2 Access to the interior 3 Fitting the lamp 1 4 Lamp alignment 5 Power cable construction 1 6 Giotto Spot s power supply 7 Installing the fixture on a support structure 8 Positioning the fixture 1 9 Installing clamps 2 0 Signal cable construction 2 1 Construction of the DMX terminator 2 2 RS 232 connection 3 Microcomputer control 3 1 Navigating in the menu 3 2 Allocating the start channel 3 3 Pan direction 3 31 Limiting Pan 3 4 Tilt direction 3 41 Limiting tilt 3 5 Inverting Pan Tilt 3 6 Lamp elapsed time meter 3 61 Resetting the lamp s elapsed time meter 3 7 Lamp strike counter 3 71 Resetting the lamp s strike counter 3 8 Fixture operating tim
27. ses lamp life The lamp obviously immediately returns to full power as soon as the shutter or dimmer is opened again Should any problems arise a reset command can be sent to the fixture so that all the motors return to the starting posi tion before beginning to carry out the commands received from the lighting console DMX512 Level range 0 255 FUNCTION _____0 60 Of 61 129 LAMP 130 179 _______ ___ _ _____ ________ 180 239 RESET 240 255 28 CONVERSION TABLE DMX MSPEED DMX MSPEED DMX MSPEED DMX MSPEED DMX MSPEEDS DMX 221 222 __5 241 50 i7 95 it 140 185 22 223 pe 240 51 169 96 110 441 59 186 22 224 225 8 c 53 166 98 108 143 57 188 20 26 __ 234 54 165 99 106 144 56 189 20 227 228 229 230 231 232 EMEN 224 157 BEGUN oo 50 ic ee 16 222 61 155 106 151 49 196 16 234 235 236 237 205 238 L 21 214 66 149 41 92 156 45 207 13 239 240 23 211 68 146 113 90 158 43 203 12 24 a 25 _ ESSE umorem Sass 2a oo Ea aaa pea 34 35 36 Ae es em ESTER EUN 48 4 43 __ 44 45 24 209 69 145 m4 oo 159 42 204 12 242 25 243 26 206 71 142 116 86 161 40 206 1 244 27 245 28 246 29 247 30 248 EM o 135 NEUE 30 ee oc QD 32 197 77
28. the display Use the UP DOWN keys to find the SMD menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select the type of resolution required Press ENTER to confirm the modifications 3 11 Remote control of lamp ignition Operators can decide if the ignition of the Giotto s lamp is to be controlled from a lighting console or be automa tic To access this function proceed as follows Op duc Goi 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the ctr menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select the required option Press ENTER to confirm the modifications OL cm 3 12 Remote control of fixture reset Using this menu it s possible to decide whether to reset the fixture via remote control or not To enable this function proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the RST ctr menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select the required option Press ENTER to confirm the changes 2E Oily DD C5 CD wm Giotto spot rel 1 00 Giotto spot rel 1 00 3 13 Display brightness Operators c
29. the fixture Make certain that no inflammable liquids water or metal objects enter the fixture Should any liquid be spilled on the fixture disconnected the power supply to the fixture immediately In the event of serious operating problems stop using the fixture immediately and either contact the nearest SGM sales point for a check or contact the manufacturer directly Do not open the fixture there are no user serviceable parts inside Never try to repair the fixture yourself Repairs by unqualified people could cause damage or faulty operation Contact your nearest authorized service centre When carrying out any work always comply scrupulously with all the norms particularly regarding safety currently in force in the country in which the fixture s being used Always insist on original spare parts being fitted General warranty conditions e The unit is guaranteed for 12 months from the date of purchase against manufacturing material defects Breakdown caused by carelessness and improper use of the fixture is excluded e The guarantee is no longer valid if the unit has been tampered with or repaired by unauthorized personnel Replacement of the fixture is not foreseen by the guarantee External parts knobs switches removable parts and lamps are excluded from the guarantee these are covered by their manufacturers guarantee conditions Transport costs and related risks are borne by the fixture s owner The guarantee i
30. tion The termination avoids the risk of DMX 512 signals being reflected back along the cable when they reaches the end of the line under certain conditions and with certain cable lengths this could cause them to cancel the original signals The termination is prepared by soldering a 1200hm 1 4 W resistor between pins 2 and 3 of the 5 pin male XLR connector see diagram 2 2 RS232 connection For this connection use good quality screened coax cable RG58 50Ohms to avoid problems with signal transmission and faulty fixture operation Connectors must always be 5 pin XLRs Refer to the diagram for wiring socket wiring RS 232 423 connection input pin 1 DIGITAL SIGNAL RS 232 inr COMPUTER RS 232 OUT PROJECTOR 25 PIN 5 PIN CONNECTOR pin 3 COMMON CONNECTOR RS 232 DD C5 CD wm Giotto spot rel 1 00 Giotto spot rel 1 00 3 0 Control microcomputer Giotto Spot 1200 is equipped with a microcomputer which allows to customize the fixture to suite the type of installation In fact it s possible to assign the start address obtain information regarding lamp life and fixture operation time run test programs to check correct fixture operation and customize some parameters 3 1 Navigating in the menu When it s switched on the fixture runs a start up reset procedure and the display indicates if there s an input signal or not M MAIN POWER CONTROL The 3 keys unde
31. ut Giotto s dimmer is partially mechanical and partially electronic and allows to obtain good linear regulation as well as high operating speed and very low noise DMX512 Level range 0 255 FUNCTION 0 CLOSED 000 255 LINEAR REGULATION 255 DD C5 CD wm Giotto spot rel 1 00 Giotto spot rel 1 00 10 GOBO ROTATION CH 10 This channel is used to control the speed or positioning of the rotary gobos Rotation can be in either direction at a speed which can be regulated from minimum of 1 5rpm to a maximum of 40rpm whereas gobo s position can be set in a range of 360 The exclusive gobo rotation system ensures absolutely smooth rotation and at the same time protects the entire system from the damage caused by dust and humidity on the movement mechanism POSITIONING 0 360 176 202 STOPPED 11 PRISMS CH 11 This channel is used to select the fixture s two rotary prisms The prisms multiply projected images by 4 or 9 obtaining eye catching graphic decorative effects The prisms cannot be superimposed so must be selected singly Lastly the prism system is completely independent from the gobo system enabling them to be combined leaving light designers wide creative freedom NO PRISM INSERTED 1 2 PRISM ROTATION CH 12 This channel is used to control the speed of the fixture s two rotary prisms ROTATION DOWN MAX ROTATION DOWN MIN ROTATION UP MIN ROTATION UP MAX 2
32. ws 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the Test menu Press ENTER and hold it down for a few seconds to confirm The message on the display will start to flash Use the UP DOWN keys to select the program corresponding to the part of the fixture to be tested Press ENTER to run the test program To quit the test functions press ENTER once then press it again for a few seconds until Test re appears on the display 3 16 Control of the acceleration of movement speed Movement can be optimized by changing the speed SPEED and acceleration ACCEL parameters obtaining smooth fast or slow movements as required To optimize movement proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the Speed or Accel menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select the required option Press ENTER to confirm the changes 3 17 dmx diy This allows to set the for how many seconds the fixture s last operating settings are maintained should there be no DMX signal This function is indispensable in those cases in which there is an accidental DMX failure To set the required time proceed as follows RON 1 Connect Giott
33. ws to see for how many hours the fixture has been operating This meter cannot be reset To see for how many hours the fixture has been used proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display 2 Usethe UP DOWN keys to find the Scn H menu The number of fixture operating hours will be displayed automatically 3 9 Input signal This function allows to choose the type of input signal to be used DMX 512 or RS 232 To select the required signal proceed as follows 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on the display Use the UP DOWN keys to find the SignZDMX menu Press ENTER to confirm The message on the display will start to flash Use the UP DOWN keys to select the type of signal to be used Press ENTER to confirm the changes c RON 3 10 Pan Tilt movement resolution This function allows to define the movement resolution 16 or 8 bit The difference is in the number of steps in which the range of head movement is divided In 16 bit mode 540 of Pan and 270 of Tilt are divided into 65 536 steps ensuring very smooth precision even at very low speeds In 8 bit mode the number of steps is 256 which nevertheless allow precise movements 1 Connect Giotto Spot to the power supply wait till it has completed reset operations and DMX signal appears on
34. y the SGM Research amp Development Centre which ensures flicker free light bright steady light beams and lower weight than fixtures with traditional ballasts Movement pre cision and speed are guaranteed by stepper motors controlled by no less than 5 microprocessors An ingenious system allows the fixture to be automatically repositioned in the event of accidental head movement Thanks to its truly innovative technical features Giotto Spot 1200 is a fixture able to offer Lighting Designers excellent solutions to all their needs LIGHT TECHNOLOGY Made in Italy by SGM Electronic Stampato in Gennaio 2000 Rel 1 00 Main features Lamp Giotto Spots use a Philips MSR 1200SA 6500 K discharge lamp without doubt the ideal light source for this type of fixture as it combines reliability and long life approximately 500 with astonishing luminous power Effects Iris Linear 0 100 dimmer Shutter Strobe from 1 10 fps can run in music sync Electronic focus 72 colors effects wheel Colorchanger with music sync and or blackout 4 rotary indexed gobos 4 fixed all interchangeable 24 gobo combinations obtainable by superimposing the two wheels Gobo change with music sync and or blackout 2 rotary prisms with adjustable speed in both directions 1 variable filter frost 1 frost filter with adjustable beam 1 3 200 K color conversion filter full CTO 1 half CTO conversion filter Movement 540 Pan

IL-GIOTTO1200S Manual - Techni-Lux

Contents

Download Pdf Manuals

Related Search

Related Contents