GC3007(A) Ultrasonic Distance Measurer - Sunsky
Contents
1. GC3007 A Ultrasonic Distance Measurer OWNER S MANUAL PREPARATION INSTALLING BATTERIES Your measurer requires 9V battery not supplied for power For the best performance and life we recommend alkaline battery Follow these steps to install a battery 1 Slide the battery compartment cover in the direction of the arrow to remove it 2 Snap the battery in the compartment as indicated by the polarity symbols and marked inside 3 Replace the cover When LOW BATT appears or the measurer stops operating properly replace the battery Caution If you do not plan to use the measurer for a month or more remove the battery Batteries can leak chemicals that can destroy electronic parts STABILIZING THE MEASURER Your measurer is sensitive to changes in temperature and humidity Before you use the measurer wait about 15 30 minutes for it to stabilize to the current room s temperature OPERATION TURNING THE MEASURER ON OFF To turn on the measurer press MEASURE The measurer turns itself off if no key is pressed within about 4 minutes or press MEASURE for 3 seconds to turn it off TAKING A MEASUREMENT 1 Press MEASURE to turn on the unit The measurer beeps then the distance between the measurer and the point you measured appears 2 Hold the bottom of the measurer flat against a wall about halfway between the floor and ceiling Be sure there is a clear path to the point you want to measure and that your head or hand2. de then add the two measurements SAVING A MEASUREMENT 1 Follow the steps under Taking a Measurement to measure a dimension 2 Press STORE then a memory key M1 M2 or M3 M and the number of the memory location you chose 1 2 or 3 appear and the measurer stores the reading in that memory location 3 If necessary repeat steps 1 and 2 to save up to three measurements 4 To display a measurement stored in a memory location press that memory key M1 M2 or M3 The measurement stored in that memory location appears To delete a measurement stored in a memory location simply store a new one in its place To clear all stored measurements hold down ALL MEMORY CLEAR for about 3 seconds The measurer beeps and M and the number of the memory location you chose 1 2 or 3 disappears Note Data of AREA or VOLUME can not be saved CALCULATING VOLUME To find the volume of a room measure the height width and the length of the room and store each measurement in a different memory location see Saving a Measurement Then press VOLUME the volume calculation result appear CALCULATING AREA Follow these steps to find the area of any two stored measurements 1 Measure the width and length of a room and store the measurements in M1 and M2 see Saving a Measurement Press AREA M1 and M2 the area calculation appear ADDING SUBTRACTING STORED MEASUREMENTS 1 Measure any two dimensions of a room and store the measur
3. ements in memory locations 1 and 2 see Saving a Measurement 2 Press ALL MEMORY CLEAR 3 Press M1 M2 then to add the measurements or M1 M2 then to subtract them The value of the calculation appears 4 To clear the display and do another measurement press ALL MEMORY CLEAR USING LASER To have a laser pointer press LASER The laser pointer disappears automatically after about five seconds This feature is only for GC3007 USING Backlight You can light up the display screen with the LIGHT key for easy viewing even 3 in a dimly lit area This function is only for GC3007A SPECIFICATIONS Power SOUrGE odcina oae aaia aiaa 1x9V Unit of measurement Feet or Meters ACCUIACY E T ie ieeand 0 5 1digit 8 60ft 1 1digit 2 8ft Working Frequency 2 e eceeeeeeeeeeeeeeeeeeeeaees 40kHz Working Temp 0eeeee 32 to 109 4 F 0 to 43 RANQC sreci aa a r n 2 to 6Oft 0 61 to 18 288m Specifications are typical individual units might vary Specifications are subject to change and improvement without notice Caution e The laser emitted from the unit is visible laser of 650nm wavelength e Don t stare into the laser beam and also don t shoot laser beam to any other s eyes e Class II laser product Output lt 1mw Notes The product has passed EN60825 1 1994 A11 1996 Corresponding label is affixed on the back of the unit
4. s do not block the front of the measurer 3 Repeatedly press FEET METER until FEET appears to measure in feet or until METER appears to measure in meter 4 Press and hold down MEASURE to take a continuous measurement Notes e The measurement appears for about 4 minutes or longer if you press another key e ERROR might appear if you try to measure a distance shorter than the set range of 2 feet 0 61m or longer than 60 feet 18 288 meters Measuring Tips e Some types of curtains and blinds can absorb sound waves causing measurements to be inaccurate If you are measuring distances in a room with curtains open the curtains before measuring the distance to a window behind them Also be sure that the window is closed e If there is not a clear path between the points where you are measuring you might receive a false reading from sound waves bouncing off objects such as chairs tables and objects with uneven surfaces If you are not sure if a measurement is correct move slightly to one side then measure the distance again e If the surface of a wall you are measuring is not solid and flat of if you are measuring in a narrow corridor you might receive a false reading If this happens use a solid surface to measure or move to the center of the corridor To measure a distance longer than 60 feet 18 288meters select a point in the middle of the room for example measure from the center of the room toward each si
Download Pdf Manuals
Related Search