Grandview Smart Screen User Manual
Contents
1. on the casing and mount the sensor in line of sight with the remote Now use the remote to lower and retract the screen Using 12V Trigger Connect the projector and screen with the jack plug cable provided Turn ON the projector and choose 12V from the menu the screen will lower When the projector is turned OFF the screen will retract into the casing Limit settings The screen is fitted with 2 limits The limits automatically stop the screen in the fully UP top limit and fully Down bottom limit positions You can adjust the bottom limit to set your viewing height Setting the top limit Adjusting the top limit may damage your screen and void your warranty For this reason the top limit screw is covered by a warning sticker Do not adjust the top limits yellow screw under any circumstance Setting the bottom limit Caution Setting the bottom limit beyond the black leader may render your screen inoperable and void your warranty The bottom limit switch is accessible through a grommeted hole on the left side of the casing Lower the screen to the operating position then insert the supplied Hex key into the white coloured screw Turn it clockwise to raise the screen or turn it anti clockwise to lower the screen When lowering the bottom limit the screen will move as you adjust it When raising the bottom limit please lift and lower the screen with the remote or side buttons to2. see the new limit setting Using close contact Simply connect the Blue and Yellow wires to L of control system and the red wire to N Then using commands in the control system screen will open and close to it s pre set limits J1 1 UP L Blue 2 DOWN L Yellow EXTERNAL CTRL 3 4 N Red 5 y Red s GND 6P6C Dry contact for Central control like AMX or Crestron UP and Down connect with L of Central control GND connect with N of central control
3. Excessive motor use The motor will switch off if the screen is used continously for more than three minutes Allow the motor to cool for 30 minutes before using again If you do not expect to use your screen for some time please disconnect the power Protecting your Screen To ensure long lasting viewing enjoyment keep the screen rolled up when not in use Check both the front and back surfaces before retracting into the case to make sure it is free of dust dirt insects or other foreign matter Use a soft brush or cloth to lightly remove any foreign particles Cleaning your Screen Use warm water with a mild detergent to remove any marks on the surface only dab do not rub or screen casing Immediately dry the screen with a soft cloth or towel Do not leave it to air dry Never use any solvents chemicals or abrasive cleaners on the screen surface as they can permanently damage the screen surface Note Warranty does not cover un installing or re installing unit GRANDVIEW Imported and Distributed in Australia by Herma Technologies Factory 4A 6 Albert St Preston VIC 3072 For more information please go to www grandviewscreens com au or call 1300 730 025 Sep 10 V1 3 GRANDVIEW Grandview Smart Screen User Manual To the owner Congratulations on purchasing a Grandview Smart Screen This screen is designed to produce the sharpest most pleasing pictures with maximum convenience Before you star
4. t e Use the correct tools a level a measuring tape and a pencil to mark with e Measure the bracket position accurately before attaching to the wall or ceiling Do not mount the brackets the full width of the casing allow at least 100mm at each end for horizontal picture alignment Wall mount Mount the brackets firmly eg into wall studs or bricks Ensure the brackets are in level nee Undo the screen as shown below Locking screw Slide the screen onto the brackets and snap into the groove and tighten the screw Up groove o Down groove Si Ceiling installation Attach the ceiling brackets as shown Slide the screen and lock Ensure the wall bracket is secured to the casing of the screen before hanging Caution Before operating the screen you must remove the white adhesive tape which holds the dropper bar to the screen case Electrical installation Grandview Smart Screens come with an Australian standard plug Simply plug in and your screen is ready to use Operating Instructions Using IR Remote Your remote control comes with a battery installed To operate your remote Press to lift the screen Press to stop the screen Press V to lower the screen The Micro switch is used for retracting or lowering screen in small increments Alternatively you may also use the external IR receiver cable and sensor Plug the IR receiver cable into the IR socket
Download Pdf Manuals
Related Search