AGS SERIES
Contents
1. c The scale is turned on d The ZERO INDICATOR is on If not press ON ZERO to set display to zero 5 2 WEIGHING a Always place an object onto the platter gently Excessive force applied to platter may cause damages to sensor inside scale b The weight of the object would be displayed automatically c It is a good practice to remove all loads from platter after weighing It would prolong the lifetime of scale 5 3 SELECT WEIGHT UNIT Press MODE to shift between metric or avoirdupois weight units The weight unit used before power off would be employed when the scale is turned on again NOTE To comply with the law of certain countries and certain approval requirements the avoirdupois weight units may be disabled Contact your dealer for more information 5 4 SET BACKLIGHT Follow the below steps to turn on and off backlight if purchased a Scale is on b Press and hold ON ZERO until backlight is activated or press MODE to shift between metric and avoirdupois weight to turn on and off backlight 5 5 SMART POWER SAVING FUNCTION The backlight function will turn off when constant zero weight is detected and remains stable for about 20 10 seconds Backlight will be automatically turned on again when a new weight is detected 5 6 SET DISPLAYED VALUE TO ZERO WHEN UNLOADED By pressing ON ZERO a positive or negative weight displayed will be set to zero and ZERO INDICATOR appears Refer to SPECIFICATIONS for maxi2. 2 Select Auto Power Off Setting The scale is equipped with Auto Power Off Function The scale will power off automatically if it is not used for 4 minutes Follow the below steps to enable disable Auto Power Off Function a b c d Scale is off Press and hold TARE then press ON ZERO Scale displays F 1 Press TARE three times Scale displays F 4 Press MODE to shift between 0 _OFF and 4 _OFF To enable Auto Power Off Function press TARE when 4 _OFF appears To disable Auto Power Off Function press TARE when 0 _OFF appears Press ON ZERO to restart the scale or TARE for next function setup 4 2 3 Select Auto Tare Function This scale is equipped with auto tare function which tares off the initial weight automatically when this function is engaged The tare weight is automatically cleared when everything is removed from platter a Scale is off b Press and hold TARE then press ON ZERO C Scale displays F 1 Press TARE six times Scale displays F 9 Press MODE to select between Tr_on or TroFF To enable Auto Tare Function press TARE when Tr_on appears To disable Auto Tare Function press TARE when TroFF appears Press ON ZERO to confirm and restart the scale or TARE for next function setup 5 INSTRUCTION FOR USE 5 1 BEFORE WEIGHING Make sure that a The stainless steel platter is placed correctly on top of load receptor b The scale is placed on a level and strong surface
3. AGS SERIES ELECTRONIC WEIGHING SCALE OPERATION MANUAL PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE Specifications subject to change without prior notice CONTENTS CAUTIONS 1 INSTALLATION SPECIFICATIONS KEYBOARD LAYOUT AND DESCRIPTION INITIAL SETUP INSTRUCTION FOR USE TROUBLE SHOOTING DAILY CARE AND MAINTENANCE CAUTIONS 1 INSTALLATION 1 This unit is legal for trade only when it is sealed and or stamped 1 1 Check and make sure that the following accessories are and bearing a serial number Do not attempt to break the seal or included stamp affixed to this scale or remove the serial number Contact Operation Manual x 1 your dealer for more information and after sales service Scale x 1 Stainless steel platter x 1 2 For most accurate weighing result do not use this scale in where Power adaptor x 1 or when the environment condition falls beyond as those listed on Dust Cover x 1 SPECIFICATIONS Contact your dealer if any item is missing 3 Do not attempt to open this unit or conduct any trouble shootings 1 2 Place the stainless steel platter on the scale other than those listed on TROUBLE SHOOTING 1 3 Power on the scale 4 Do not use this scale for chemical substances or in any a Before charging the scale or power on with the adaptor environment that contains chemical vapor supplied Please make sure the input voltage listed on the back of the adaptor matches with the lo
4. ate a Weighing Result to Memory a Refer to 5 2 to 5 3 for weighing b Press M to save and accumulate the result to memory c Scale will display P X and then follow by the accumulated weighing result stored while both M INDICATOR and MEMORY RECALL INDICATOR appear pointing to M and MR on the overlay respectively d Scale return to normal after 2 seconds and MEMORY RECALL INDICATOR will turn off automatically but M INDICATOR will remain on display to indicate that memory contains a stored data e Repeat a to c for subsequent transactions NOTE 1 P X means the total number of transactions accumulated to memory NOTE 2 No weighing result will be stored to memory if it is less than the minimum load Please refer to SPECIFICATIONS for more information NOTE 3 When scale is set at OIML and application is legal for trade User only needs to press M once when trying to store a value to memory The weight accumulation function will take place when reading is stabled When scale is set at Non OIML and application is not legal for trade User can save the shown value to memory at anytime when pressing M 5 9 2 Memory Recall a Press MR b Scale displays P X and then follow by the accumulated weighing result while MEMORY RECALL INDICATOR appears pointing at MR c Scale return to normal after 2 seconds and MEMORY RECALL INDICATOR will switch off with only M INDICATOR remain on display 5 9 3 Memo
5. cal voltage If not 5 Precision measuring instrument handle with care do not use it and contact your dealer immediately b Before first time use charge the scale for at least 8 hours 6 Do not open scale No user serviceable parts inside to ensure the best performance 2 SPECIFICATIONS Model No Capacity Division e Max OIML Non OIML Extended AGS 1500 1500g 0 5g 0 2g 0 05g AGS 3000 3000g 1g 0 5g 0 1g AGS 6000 6000g 2g 1g 0 2g AGS 15K 15kg 0 005kg 0 002kg 0 0005kg AGS 30K 30kg 0 01kg 0 005kg 0 001kg Tare Range Full Tare Range Power on Zero 10 Max Range Zero Range 2 Max Min Load 20e Power Source By Built in Rechargeable Battery or AD DC Power Adaptor Operating Environment 0 40 C 32 104 F Non condensed R H 5 Specifications subject to change without notice NOTE 1 OIML Legal for trade 1 3000 Non OIML Not legal for trade 1 6000 1 7500 NOTE 2 Extended Display Function does not support avoirdupois weight units Ib lb and Ib oz 3 KEYBOARD LAYOUT AND DESCRIPTION O i OFF B88 ON s iat TARE ZERO AGS 1 T OO O 1 OFF KEY Press this key to turn scale off 2 ON ZERO KEY Press this key to turn scale on or set weight to zero 3 MODE KEY Press this key to shift among different weight units and or turn backlight on off 4 TARE KEY Press this key to tare off t
6. ched Is the NET INDICATOR on Turn the scale off Remove all loads from platter and turn on again Is there anything obstructing the platter Remove all obstacles Weighing result is not accurate Is the scale placed in a level condition Adjust the adjustable feet to a level condition Is the scale affected by airflow vibration or RFI Place the scale away from all disturbances Is the scale calibrated correctly Contact your dealer Is the correct weight unit employed Refer to 5 3 for weight unit setting and usage Display shows 00000 after counting down Is the load applied to platter excess the rated capacity of scale Remove all loads from platter and try again 7 DAILY CARE AND MAINTENANCE 7 1 7 2 7 3 Clean the scale with a soft and damp cloth If necessary apply a mild detergent Do not use any harsh abrasive material acetone volatile solvent thinner or alcohol for cleaning Verify the accuracy of scale periodically Re calibrate the scale if necessary NOTE In some countries calibration requires authorized qualified agent Contact your dealer for more information 7 4 7 5 7 6 7 7 It is a good practice to apply the dust cover when operating the scale The scale must be placed horizontally during transportation or long time storage Remove platter from scale before transportation or long time storage Store scale in a dry and clean place
7. he weight of a container 5 FUNCTION KEY Press this key to enter counting function or percentage function 6 SAMPLE KEY Press this key to sample the weight place on the platter and engage the counting function or percentage function 7 MODE INDICATOR This indicator shows current weight unit or operating mode engaged 8 ZERO INDICATOR This indicator appears to indicate a zero weight status 9 NET INDICATOR This indicator appears to indicate the tare function is in operation and weight displayed is net weight 10 LO BAT INDICATOR When this indicator appears recharge the scale immediately Failure to do so may cause unrecoverable damage to the rechargeable battery inside scale 4 INITIAL SETUP 4 1 PLACING THE SCALE In order to obtain an accurate weighing result the scale must be placed on a strong and level surface If required adjust the adjustable feet underneath scale to obtain a level position Refer to the bubble indicator for leveling condition 4 2 INTERNAL SETTING 4 2 1 Display Segment Check User can enter this function to check to see if the display and backlight if purchased are functioning properly a Scale is off b Press and hold TARE then press ON ZERO c Scale displays F 1 d Press TARE once e Scale displays F 2 f Press MODE and all segments will light up to allow user to check the condition of display g Press TARE for next function setup or ON ZERO to restart the scale 4 2
8. mum zero range NOTE When scale is set at OIML and application is legal for trade User only needs to press ON ZERO once when setting the value to zero The re zero function will take place when reading is stabled When scale is set at Non OIML and application is not legal for trade User can set the value to zero at anytime when pressing ON ZERO 5 7 TARE OFF THE WEIGHT OF A CONTAINER When a container is used follow the below steps to manually tare off the weight of container and get the net weight a Remove all loads away from platter b Make sure that the ZERO INDICATOR is on 9 Place the container on the platter d Press TARE After TARE is pressed the NET INDICATOR would appear Refer to 5 2 for weighing procedures Weight displayed under is the net weight of the subject matter Refer to SPECIFICATIONS for maximum tare range NOTE When scale is set at OIML and application is legal for trade User only needs to press TARE once when tare off a weight The tare function will take place when reading is stabled When scale is set at Non OIML and application is not legal for trade User can tare off the weight anytime when pressing TARE 5 8 CLEAR THE TARE FUNCTION a Remove all loads from platter b The tare effect will be cancelled Automatically if automatic tare function is employed or By pressing TARE c After TARE is pressed the NET INDICATOR would disappear 5 9 MEMORY FUNCTION 5 9 1 How to Accumul
9. ry Clear a Press MR and TARE at the same time b Scale displays P 0 and MR INDICATOR at the same time and return to normal after 2 seconds and M INDICATOR will switch off 5 10 EXTENDED DISPLAY This scale is equipped with extended display function for reference purpose only To activate the function press and hold MODE for 2 seconds and display will flash the extended digit for 5 seconds before return to normal 5 11 RECHARGE THE SCALE The scale is equipped with a built in rechargeable battery When the LO BAT INDICATOR appears recharge the scale immediately Failure to do so may cause unrecoverable damage to the rechargeable battery 6 TROUBLE SHOOTING Syndrome Check Action Check Action Syndrome Check Action Check Action Scale cannot be turned on Is the scale charged Recharge the scale for at least 8 hours before first time use or plug in the power adaptor before power on the scale Is the power adaptor inserted properly into both the electricity outlet and the DC inlet of scale Secure both ends of the power adaptor and try again Scale turned off automatically Is Auto Power Off Function employed Refer to 4 2 2 to disable Auto Power Off Function Is the LO BAT INDICATOR on Apply the power adaptor Syndrome Check Action Check Action Syndrome Check Action Check Action Check Action Check Action Syndrome Check Action Rated capacity cannot be rea
Download Pdf Manuals
Related Search