HITACHI Projector CP-X2020/CP-X2520/CP
Contents
1. Press the MENU button to display a menu 2 Point at the ADVANCED MENU in the menu using the V A button then press the button 3 Point at the OPTION in the left column of the menu using the V A button then press the gt button 4 Point at the LAMP TIME using the 4 button then press the gt button A dialog will appear 5 Press the gt button to select OK on the dialog It performs resetting the lamp time NOTE Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp 57 Replacing the lamp continued Lamp warning A HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE AWARNING P The projector uses a high pressure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition if the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury and dust containing fine particles of glass to escape from the projector s vent holes gt About disposal of a lamp This product contains a mercury lamp do not put it in a trash Dispose of it in accordance with environmental laws e For lamp recycling go to www lamprecycle org in the US e For product disposal consult your local government agency or www eiae org in the US or w2. type will come together with a replacement lamp for this projector 1 Turn the projector off and unplug the power cord Allow the projector to sufficiently cool down Use a vacuum cleaner on and around the filter cover Pick and pull up the filter cover knobs to take it off Use a vacuum cleaner for the filter vent of the projector a WN Take the fine meshed filter out while holding the filter cover It is recommended to leave the coarse meshed filter in the filter cover as it is 6 Use a vacuum cleaner on both sides of the fine meshed filter while holding it so it will not be sucked in Use a vacuum cleaner for the inside of the filter cover to clean up the coarse meshed filter If the filters are damaged or heavily soiled replace them with new ones Intake vent 7 Put the fine meshed filter on the coarse meshed one turning its stitched side up Filter coarse meshed 8 Put the filter unit back into the projector Filter fine meshed SOS Stitched Sei side continued on next page ih 59 Cleaning and replacing the air filter continued 9 Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU 1 Press the MENU button to display a menu 2 Point at the FILTER TIME using the W A button then press the gt button A dialog will appear 3 Press the button to select OK on the dialog It performs resetting the filter time
3. Maintenance Replacing the lamp A lamp has finite product life Using the lamp for long periods of time could cause the pictures darker or the color tone poor Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them Preparation of a new lamp and early replacement are recommended To prepare a new lamp make contact with your dealer and tell the lamp type number Type number DT01141 Replacing the lamp 1 Turn the projector off and unplug the power cord Allow the projector to cool for at least 45 minutes 2 Prepare a new lamp If the projector is mounted on a ceiling or if the lamp has broken also ask the dealer to replace the lamp Lamp cover In case of replacement by yourself follow the following procedure 3 Loosen the screw marked by arrow of the lamp cover and then slide and lift the lamp cover to the side to remove it Loosen the 2 screws marked by arrow of the lamp and slowly pick up the lamp by the handle Never loosen any other screws 5 Insert the new lamp and retighten firmly the 2 screws of the lamp that are loosened in the previous process to lock it in place While putting the interlocking parts of the lamp cover and the projector together slide the lamp cover back in place Then firmly fasten the screw of the lamp cover 7 Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu 1
4. NOTE Please replace the air filter when it is damaged or too soiled e When you replace the projection lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector e Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter e The projector may display the message such as CHECK THE AIR FLOW or turn off the projector to prevent the internal heat level rising 60
5. injury e Use only the lamp of the specified type Use of a lamp that does not meet the lamp specifications for this model could cause a fire damage or shorten the life of this product e If the lamp breaks soon after the first time it is used it is possible Q that there are electrical problems elsewhere besides the lamp If this happens consult your local dealer or a service representative e Handle with care jolting or scratching could cause the lamp bulb to burst during use e Using the lamp for long periods of time could cause it dark not to light up or to burst When the pictures appear dark or when the color tone is poor please replace the lamp as soon as possible Do not use old used lamps this is a cause of breakage 58 Cleaning and replacing the air filter The air filter unit of this projector consists of a filter cover two kinds of filters and a filter frame The new double large filters system is expected to function longer However please check and clean it periodically to keep ventilation needed for normal operation of the projector When the indicators or a message prompts you to clean the air filter comply with it as soon as possible Replace the filters when they are damaged or too soiled To prepare new filters make contact with your dealer and tell the following type number Type number UX36761 Filter set When you replace the lamp please replace the air filter An air filter of specified
6. ww epsc ca in Canada For more information call your dealer e If the lamp should break it will make a loud bang when it does unplug the power cord from the outlet and make sure to request a replacement lamp from your local dealer Note that shards of glass could damage the projector s internals or cause injury during handling so please do not try to clean the projector or replace the lamp yourself Disconnect If the lamp should break it will make a loud bang when it does ventilate the the plug room well and make sure not to inhale the gas or fine particles that come out from the from the projector s vent holes and not to get them into your eyes or mouth power Before replacing the lamp turn the projector off and unplug the power outlet cord then wait at least 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp e Never unscrew except the appointed marked by an arrow screws e Do not open the lamp cover while the projector is suspended from a ceiling This is dangerous since if the lamp s bulb has broken the shards will fall out when the cover is opened In addition working in high places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken e Do not use the projector with the lamp cover removed At the lamp replacing make sure that the screws are screwed in firmly Loose screws could result in damage or
Download Pdf Manuals
Related Search