UM0972030
Contents
1. off shore and maritime Our objective is to design and produce camera systems for the professional market that improve the drivers view and increase operating efficiency At our factory in Barneveld we have a production department warehouse design department service department and showroom Vision is our mission Orlaco therefore deploys the development manu facture supply and service of camera and display systems that will improve Safety and effi ciency of all vehicles machinery and vessels Our systems will give the end user a view on each blind spot and will create comfort and improved working conditions Our active approach will support market demands and innovations and will lead to enthusiastic ambassadors in the market our Customers For more information www orlaco com ORLACO PRODUCTS BV Albert Plesmanstraat 42 3772 MN Barneveld PO Box 193 3770 AD Barneveld The Netherlands Phone 31 0 342 404555 E mail info orlaco com UMOSTF PO30ENR1 1 Internet http www orlaco com e ORLACO Specialised Camera Solutions2. LED indicator When in these MENUS the LED Indicator will slowly flash RED to indicate that the unit is not ready to record Also video and audio outputs will be disabled See figure 3 g g oe Led indicator table No light Unit is not powered Not recording Green light Unit is on Stand by Mode Not recording Figure 3 Red light Recording Card change or remove Only when no light 4 UM0972030 R1 1 N ORL LACO l 9 Menu structure e Recordings list e Controls Recording quality HIGHEST HIGHER NORMAL SUBNORMAL LOWER LOWEST Video resolution VULL VIDEO 2 3 HORIZONTAL ONE QUARTER Audio input controls AUDIO GAIN LEVEL PRESETS x4 CUSTOM INT EXT MIC LEVEL HIGH LOW SOURCE MIXING ON OFF LOOP RECORDING LOOP RECORD Not recommended RECYCLE RECORD FILE SIZE LIMIT o Setup Set date and time File names Display contrast Serial number e Features On Screen Displays TIME DISPLAYS TIMER FRAME COUNT BACK GROUND LOCATION GFORCE MODULE BACKGROUND LOCATION TEXT SCALE ORIENTATION Auto record at start Auto shut down IF NOT RECORDING IF NOT EXT POWER TIME DELAY Record switch style Advanced Data Acquisition use only NORMAL HOLD DOWN STOP DELAY Gforce record trigger DIFFERENCES THRESHOLD MODE SENSITIVITY G s TIME DELAY AFTER UM0972030 R1 1 5 N SR AC a 6 Setting date and time The contr
3. Easy solid recorder User manual No UM0972030 R1 1 _ Art No 0000200 ee i 12 2011 English e ORLACO Specialised Camera Solutions Easy solid recorder Manual no 1M0972040 Version R1 1 Introduction This manual contains user instructions Used photographs and illustrations give general information and may differ from the products you use Contact your Orlaco dealer if you have questions additional information or want to make changes that are not described in this manual All data subject to change without notice All dimensions are for commercial purpose only The camera display systems from Orlaco comply with the latest CE ADR EMC and mirror directive regulations where applicable All products are manufactured in accordance with the ISO 9001 quality management system ISO TS 16949 quality automotive ISO 14001 environmental management systems where applicable Content page 1 Menus Set Up and Use 2 Recording 3 Saved Settings 4 Top menu 5 Menu structure 6 Setting date and time 7 Release notes Oooh B BW OW Available Documentation DS0000200 Data sheet Included All in One Card Reader USB 2 0 Article number 2130630 32GB Compact Flash Card Article number 0060210 2 UM0972030 R1 1 N ORL ACO 1 Menus Set Up and Use Powering On and Recording Standby Mode Recording The control buttons and LCD screen are in the housing The housing cover can be removed by unscrewing th
4. e 4 screws See figure 1 The opening screen on the LCD when powering up the Easy Solid Recorder will briefly display the software version along with the date of the software version See figure 2 Then the Easy Solid Recorder goes into automatic Recording Standby mode The LCD screen will be backlit for a period of 30 seconds Recording Standby The LCD screen will show the date and time at the top Below that is an active audio input meter which is shown as a bar graph An asterisk at the end of the audio bar graph will indicate that the sound is being clipped Video status will be shown as NO INPUT or READY The Compact Flash status will be displayed as NOT IN FULL or READY The bottom line will indicate the remaining capacity of the card bar graph and calculated recording time available In Recording Standby mode pressing and holding the Power Re cord key or remote button continuously for two seconds will turn off the Easy Solid Recorder See figure 3 2 Recording Pressing the Power Record key or remote button will start and stop recording When recording the LCD backlight is turned off video output is turned off by default audio output is turned off The LCD screen will show RECORDING And a line identifying the file path and name will be displayed If the unit is not ready to record the LCD backlight will flash and the LCD will display NOT READY TO RECORD and return to R
5. ecording Standby mode NOTE If an attempt was previously made to record to a CF Card that was not fast enough there will be an error message displayed FLASH MEDIA WAS TOO SLOW after the recording is stopped The recording is made but it will contain skips and may cause errors in player software There will be a number to indicate 0 10 the severity of the problem Recording will end when the CF Card is full power drops too low the Easy Solid Recorder will also turn off or the Power Record or remote button is pushed UM0972030 R1 1 rs 6 5 lt OR ACO KS 4x Socket head screws Figure 1 LCD merrell ee Figure 2 Power record key LED indicator CO ca O Figure 3 3 Saved Settings CD Screen The Easy Solid Recorder will store the settings as programmed by the user if when not powered You will not need to enter in the set tings more than once unless you want to change the settings 4 Top menu See figure 2 At the Recording Standby Mode press the MENU key on the keypad You will see four options RECORDINGS LIST CONTROLS SETUP and FEATURES Press MENU or ESCAPE X to return to the Recording Standby Mode Figure 2 Pressing the UP and DOWN keys will move between and highlight Selections Pressing the center SELECT or ENTER key will bring up a new menu related to your selection Power record key
6. ol buttons and LCD screen are in the housing The housing cover can be removed by unscrewing the 4 screws See figure 1 Go to SETUP Set DATE AND TIME When the Set DATE AND TIME screen is up one field is highlighted for adjustment and the LEFT and RIGHT keys are used to change the selection to another field Year month day hour minute and second are displayed When the UP or DOWN keys are pressed the highlighted selection is adjusted up or down Pressing MENU sets the date and time according to the current display on the LCD and returns to the Recording Standby condition Pressing ESCAPE X returns to the SETUP menu previous menu without changing the date and time Time Displays You have four different ways of displaying time as text recorded directly on the video The first menu section will toggle through the options You can show DATE TIME on the video show only the actual TIME or show elapsed RECORDING TIMER Recording time is useful as a track timer See figure 4 6 KS 4x Socket head screws Figure 1 LCD Screen Figure 2 UM0972030 R1 1 SS AC 7 Release notes Revision R1 0 First issue December 2011 Revision R1 1 Pictures USB card reader and Compact Flash card deleted Februari 2015 UM0972030 R1 1 7 N OORL AC l ORLACO Orlaco is a manufacturing company specialize in making camera and moni tor systems for commercial vehicles fork lift trucks cranes
Download Pdf Manuals
Related Search
UM0972030