Home

data sheet - MEN Mikro Elektronik GmbH

1. CompactPCI Core Specification PICMG 2 0 R3 0 System slot 32 bit 32 MHz PCI to PCI bridge V I O 3 3V or 5V Universal Board Supply voltage power consumption CompactPCl standard version o 5V 3 5 10mA max o 3 3V 3 5 1A typ Supply voltage power consumption stand alone version o 5V 3 5 800mA typ a Uses 5V only MTBF 277 234h 40 C according to IEC TR 62380 RDF 2000 Dimensions conforming to CompactPCI specification for 3U boards Weight 250g Temperature range operation o 40 85 C qualified components n Airflow min 10m3 h Temperature range storage 40 85 C Relative humidity operation max 95 non condensing Relative humidity storage max 95 non condensing Altitude 300m to 3 000m Shock 15g 11ms Bump 10g 16ms Vibration sinusoidal 2g 10 150Hz Conformal coating on request PCB manufactured with a flammability rating of 94V 0 by UL recognized manufacturers Tested according to EN 55022 radio disturbance IEC1000 4 2 ESD and IEC1000 4 4 burst MENMON VxWorks Linux ELinOS QNX MSCAN Layer2 support MEN Driver Interface System MDIS for all supported operating systems For more information on supported operating system versions and drivers see Downloads Page 4 FPGA This product offers the possibility to add customized I O functionality in FPGA Flexible Configuration Customized I O functions can be added to the FPGA It depends
2. I O connector RS232 RS485 isolated or not for free use in system e g cable to front Data rates up to 115 2kbit s 16 byte transmit receive buffer o Handshake lines CTS RTS DCD DSR DTR RI CAN bus Two CAN bus channels 2 0 A B CAN protocol Data rates up to 1 Mbit s Connection via onboard connectors o External transceivers using SA Adapters GPIO a 36 GPIO lines o FPGA controlled o Connection via onboard I O connector Further I O depending on FPGA configuration n A B ood One USB 1 1 Series A Two Ethernet RJ45 One RS232 UART RJ45 Page 3 Technical Data FPGA Miscellaneous CompactPCI Bus Electrical Specifications Mechanical Specifications Environmental Specifications Safety EMC BIOS Software Support F12N Data Sheet 2013 02 06 Standard factory FPGA configuration Main bus interface 16Z070_IDEDISK IDE controller for NAND Flash 16Z043_SDRAM Additional SDRAM controller 16MB 16Z023_IDENHS IDE controller PIO mode 0 non hot swap 16Z087_ETH Ethernet controller 10 1 00Base T 16Z025_UART UART controller controls COM10 16Z034_GPIO GPIO controller 40 lines 5 IP cores The FPGA offers the possibility to add customized O functionality See FPGA 0 0 0 E E Er O Real time clock with GoldCap backup Power supervision and watchdog Reset button GPIO controlled Three user LEDs GPIO controlled 1 FPGA power status LED Compliance with
3. on the board type pin counts and number of logic elements which IP cores make sense and or can be implemented Please contact MEN for information on feasibility m You can find more information on our web page User I O in FPGA FPGA Capabilities FPGA Altera Cyclone Il EP2C20 n 18 752 logic elements o 239 616 total RAM bits Connection o Available pin count 47 pins o Functions available via onboard I O connector o SA Adapters can be used to realize the physical lines F12N Data Sheet 2013 02 06 Page 5 Configuration amp Options Standard Configurations Article No CPU Type Clock System RAM NAND Flash Boot Flash Additional SDRAM 02F012N00 MPC5200B 384 MHz 256 MB 1 GB 2 MB 16 MB Options CPU m MPC5200B 384 MHz Memory m System RAM 32 MB 64 MB 128 MB or 256 MB NAND Flash o OMB up to maximum available Boot Flash o 2 MB 4 MB or 8 MB Additional SDRAM o OMBor16MB SRAM o OMBor2 MB 128 KB non volatile FRAM instead of SRAM 1 0 Up to 8 additional I O functions through SA Adapters o Mostly implemented in onboard FPGA o RS232 RS422 485 binary I O keyboard mouse CAN o One piece 3U front panels for different SA Adapter combinations Front connections o D Sub connectors for Ethernet and COM USB Second Ethernet channel at front through FPGA Busless Also available as busless version with external 5V supply Cooling Concept Also available with conduction cooling in MEN CCA frame Please note t
4. F12N 3U CompactPCI PowerPC MPC5200B CPU Board 32 bit 33 MHz cPCI system slot 4 HP MPC5200B 384 MHz FPGA 18 752 LEs approx 225 000 gates aan Up to 256 MB onboard DDR SDRAM h Up to 8 MB boot Flash NAND Flash 2 MB SRAM 16 MB graphics memory Dual Fast Ethernet COM USB front Dual CAN bus controller FPGA for user defined I O functions MENMON BIOS for PowerPC cards hit We ht Dan na 40 to 85 C with qualified components Equipped with the MPC5200B PowerPC the F12N the MPC5200B and are accessible via SA Adapters A second serial single board computer is a versatile 3U Eurocard interface can be accessed using an SA Adapter on the F12N E IDE and CompactPCl board that operates at up to 400 MHz GPIO are also on board and 700 MIPS The F12N is designed especially for The large FPGA on the F12N allows to realize additional user defined systems which require low power consumption and functions such as graphics touch further serial interfaces further CAN mechanical robustness With the processor consuming bus controllers binary I O etc for the needs of the individual less than 1 W the board is delivered for 40 to 85 C application in a very flexible way Before boot up of the system the operation temperature All components on the board FPGA is loaded from boot Flash Updates of the FPGA contents can be are soldered The F12N is thus well placed as a rugged made inside the boot Flash during operat
5. d to work under QNX For details regarding supported unsupported board functions please refer to the corresponding software data sheets 10EM01 40 QNX 6 3 SP3 BSP MEN for EM1 EM1A EM1N EK6 EK6N F12 and F12N 10EM01 41 QNX 6 4 1 BSP MEN for EM1 EM1A EM1N EK6 EK6N F12 and F12N 10EM01 42 QNX 6 5 0 BSP MEN for EM1 EM1A EM1N EK6 EK6N F12 and F12N 13Z015 06 MDISS5 low level driver sources MEN for 16Z029_CAN MSCAN Layer2 13Z017 06 MDISS low level driver sources MEN for 16Z034_GPIO 16Z037_GPIO and 16Z127_GPIO 13Z025 40 QNX 6 3 native driver MEN for 16Z025_UART and 16Z125_UART 13Z025 41 QNX 6 4 native driver MEN for 16Z025_UART and 16Z125_UART 13Z025 42 QNX 6 5 native driver MEN for 16Z025_UART and 16Z125_UART 13Z087 40 QNX native driver MEN for 16Z087_ETH Software Firmware BIOS MENMON is MEN s firmware BIOS for PowerPC platforms 14EM01 00 MENMON Firmware for EM1 EM1A EM1N F12 and F12N object code For operating systems not mentioned here contact MEN sales Documentation Compare Chart 3U CompactPCI PlusIO CPU cards Download Compare Chart 3U CompactPClI PluslO peripheral cards Download 20F012NO00 F12N User Manual 20F012NER F12N Errata 21MENM 00 MENMON User Manual 21Z025 90 16Z025_UART and 16Z125_UART under Linux User Manual 22Z025 ER 16Z025_UART Errata 22Z087 ER 16Z087_ETH Errata F12N Data Sheet 2013 02 06 Page 8 Contact Information Germany France USA MEN Mikro Elekt
6. dditional Flash I O Connector P2 SRAM Multifunction external bus PCI 104 P1 PCI to PCI Bridge CompactPCl J1 J2 Option Busless F12N Data Sheet 2013 02 06 Page 2 Technical Data CPU Memory Mass Storage 1 0 Front Connections Standard F12N Data Sheet 2013 02 06 PowerPC o MPC5200B o Up to 400MHz 2x16KB L1 data and instruction cache integrated in MPC5200 Up to 256MB SDRAM system memory o Soldered o DDR n 64MHz memory bus frequency Up to 1GB soldered NAND Flash and more FPGA controlled 16MB additional SDRAM FPGA controlled e g for video data and NAND Flash firmware Up to 8MB boot Flash 2MB GoldCap backed SRAM or 128KB non volatile FRAM Serial EEPROM amp 8kbits for factory settings Parallel IDE PATA o One IDE port via 44 pin onboard connector o FPGA controlled o PIO mode 0 support Up to 1GB soldered ATA NAND Flash and more FPGA controlled USB o One USB 1 1 port o Series A connector at front panel o OHCI implementation o Data rates up to 12Mbit s Ethernet o Two 10 100Base T Ethernet channels o One channel FPGA controlled o Two RJ45 or one D Sub connector at front panel One RS232 UART COM1 n RJ45 or D Sub connector at front panel o Data rates up to 115 2kbit s o 512 byte transmit receive buffer o Handshake lines CTS RTS One UART COM10 Accessible via I O connector Physical interface at front panel using SA Adapter via 10 pin ribbon cable on
7. hat some of these options may only be available for large volumes Please ask our sales staff for more information F12N Data Sheet 2013 02 06 SRAM 2 MB Page 6 Ordering Information Standard F12N Models 02F012N00 MPC5200B 384MHz 256MB SDRAM 1GB NAND Flash 2MB SRAM 16MB additional SDRAM 2MB boot Flash 40 85 C qualified SA Adapters You can find a more detailed overview of possible carrier board SA Adapter combinations along with software support in our option matrix PDF 08SA01 00 RS232 not optically isolated 0 60 C 08SA02 00 RS422 485 half duplex optically isolated 0 60 C 08SA02 07 RS422 485 full duplex optically isolated 40 85 C screened 08SA03 01 1 RS232 optically isolated 40 85 C screened 08SA08 01 CAN ISO high speed optically isolated 40 85 C screened Systems amp Card Cages 0701 0046 CompactPCl 19 4U 24HP desktop system for 3U cards 3 slot 3U CompactPCl backplane system slot right 1U fan tray with 1 fan 8 HP space for 1 pluggable PSU 0701 0056 CompactPCl 19 4U 84HP rack mount enclosure for 3U cards vertical 4 4 slot 3U CompactPCl CompactPCl Serial hybrid backplane prepared for rear I O 250W power supply wide range 90 264VAC on rear 1U fan tray with 2 fans included 0 60 C MEN delivers turn key systems completely installed hardware operating system accessories wired and tested Different rack sizes power supplies and backplanes on request For details p
8. ion The FPGA functions can computing platform for mobile applications offering be physically implemented by using SA Adapters A maximum of 8 SA the whole world of Linux based software and real time Adapters can be used on the F12N and I O can be made accessible at operating support for VxWorks and QNX the front panel The CPU card is equipped with an onboard soldered Equipped with a PCl bridge chip the F12N offers a full CompactPCl SDRAM of up to 256 MB and up to 1 GB NAND Flash interface system slot functionality for reliable system expansion as well as with 16 MB additional SDRAM up to 8 MB The F12N comes with MENMON support This firmware BIOS can be boot Flash and 2 MB battery backed SRAM used for bootstrapping operating systems from disk Flash or network The SBC provides two Fast Ethernet interfaces one for hardware testing or for debugging applications without running any serial line and USB 1 1 at its front panel As an operating system alternative to RJ45 D Sub connectors guarantee reliable functions also in harsh environments Two CAN controllers with V2 0A B CAN protocol are included in men F12N Data Sheet 2013 02 06 Page 1 Diagram SDRAM Main EEPROM RTC lt gt Front panel Watchdog B Jon boara PowerPC MPC5200B wokal O RS232 COM1 lt P gt USB 1 1 gt CAN bus El ri SA bY CAN bus PB H SA fel F gt L Sy Ethernet 10 100Base T FPGA Boot Flash Du Ei SDRAM NAND A
9. lease contact your local sales representative Miscellaneous Accessories 05F006 00 RS232 interface cable RJ45 to 9 pin D Sub 1 COM to 1 COM 2m 05F500 00 Kit cables and front panel for 3 D Subs for connection of 2 CAN type SA8 and 1 COM type SA1 SA4 to F12N SA Adapters to be ordered separately Software Linux This product is designed to work under Linux See below for all available separate software packages 10EM01 90 Linux BSP MEN for EM1 EM1A EM1N EK6 EK6N F12 F12N and PP1 under ELinOS 5 0 rpm for direct installation in ELinOS This product is designed to work under ELinOS Embedded Linux by SYSGO For more information and product support please contact www sysgo com 13MD05 90 MDIS5 System and Device Driver Package MEN for Linux This software package includes most standard device drivers available from MEN Software VxWorks This product is designed to work under VxWorks For details regarding supported unsupported board functions please refer to the corresponding software data sheets 10EM01 60 VxWorks BSP MEN for EM1 EM1A EM1N EK6 EK6N F12N and F12 13Z015 06 MDISS5 low level driver sources MEN for 16Z029_CAN MSCAN Layer2 13Z017 06 MDISS low level driver sources MEN for 16Z034_GPIO 16Z037_GPIO and 16Z127_GPIO 13Z025 60 VxWorks native driver MEN for 16Z025_UART 16Z057_UART and 16Z125_UART F12N Data Sheet 2013 02 06 Page 7 Ordering Information Software QNX This product is designe
10. ronik GmbH MEN Mikro Elektronik SAS MEN Micro Inc Neuwieder StraRe 3 7 18 rue Ren Cassin 860 Penllyn Blue Bell Pike 90411 Nuremberg ZA de la Chatelaine Blue Bell PA 19422 Phone 49 911 99 33 5 0 74240 Gaillard Phone 215 542 9575 Fax 49 911 99 33 5 901 Phone 33 0 450 955 312 Fax 215 542 9577 Fax 33 0 450 955 211 info men de info men france fr sales menmicro com www men de www men france fr www menmicro com The date of issue stated in this data sheet refers to the Technical Data only Changes in ordering information given herein do not affect the date of issue All brand or product names are trademarks or registered trademarks of their respective holders MEN is not responsible for the results of any actions taken on the basis of information in the publication nor for any error in or omission from the publication MEN expressly disclaims all and any liability and responsibility to any person whether a reader of the publication or not in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance whether wholly or partially on the whole or any part of the contents of the publication The correct function of MEN products in mission critical and life critical applications is limited to the environmental specification given for each product in the technical user manual The correct function of MEN products under extended environmental conditions is limited to the individual requiremen
11. t specification and subsequent validation documents for each product for the applicable use case and has to be agreed upon in writing by MEN and the customer Should the customer purchase or use MEN products for any unintended or unauthorized application the customer shall indemnify and hold MEN and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim or personal injury or death associated with such unintended or unauthorized use even if such claim alleges that MEN was negligent regarding the design or manufacture of the part In no case is MEN liable for the correct function of the technical installation where MEN products are a part of Copyright 2015 MEN Mikro Elektronik GmbH All rights reserved F12N Data Sheet 2013 02 06 Page 9

data sheet - MEN Mikro Elektronik GmbH

Contents

Download Pdf Manuals

Related Search

Related Contents