Home

IR Intelligent Integrative Camera

Contents

1. 25 IR Intelligent Integrative Camera Installation and User Manual Parameter Index IV Technical parameter IR Illumination Distance Options 30 meters 60 meters 80 meters 120 meters 150 meters etc IR lamps control automatically switch far near IR lamp according to focal length at night Power Supply AC24V 10 Power Consumption Maximum 60W Working Temperature 30 C 55 C Manual Rotary Speed Horizontal 0 05 240 s Vertical 0 03 160 s Horizontal Rotary Range Horizontal 0 360 unlimited consecutive rotation Vertical Rotary Range Vertical 2 92 With auto flip Control Mode RS485 bus mastering support full automatic identify protocol and baud rate 3D Positioning Realize screen coordinate positioning and local enlarge by software Auto Patrol 9 groups the dwell time of preset points is adjustable Auto Sweep No less than 20 groups patrol speed and dwell time can be adjusted Reduce Speed Support intelligent focal length speed automatic matching technique Remote Help Remote fault diagnosis system upgrade reset function Soft Address Set address without dismantling the unit according to demand Pattern 4 paths record no more than 500 instructions or 10 minutes Power On Action Support 18 kinds of power on action Idle Action Support 18 kinds of idle action Camera Compatible with most
2. B series of IR intelligent high speed dome camera dimension figure Wall Monuted Pendent Mounted n i bo tel ACD IR Intelligent Integrative Camera Installation and User Manual C series of IR intelligent high speed dome camera dimension figure Wall Mounted Pendent Mounted E series of IR intelligent high speed dome camera dimension figure Wall Mounted Pendent Mounted IR intelligent high speed dome camera is designed for wall mounted and pendent mounted installation Conditions of wall mounted installation Wall mounted unit can be used in the rigid wall structure of indoor and outdoor 1 The wall thickness should be enough to install setscrews 2 The wall can withstand at least 4 times the weight of the unit Punch holes for wall mounted bracket Take the wall mounted bracket from the packing box and use the open holes at the bottom of bracket as template and draw punch positions on the wall As shown in the following figure IR Intelligent Integration Camera Installation and User Manual
3. 53 Start 3 preset point patrol Set dwell time of the 3 patrol gt gt 33 48 preset point patrol 60 Open Camera menu Need camera support 61 Close Screen display Open Screen display Screen character display 62 Close Reduce speed Open Reduce Speed 63 Start Horizontal auto scan Open close auto flip 65 Horizontal auto scan mode gt gt 66 Horizontal sweep mode gt gt Set speed of the sweep gt gt gt 470 Close Mask Open Mask 71 Delete all preset points Default is Close mode 72 Close Expert mode Open Expert mode 473 Close Alarm function Open Alarm function 79 Restore factory settings 80 Standby time setting gt gt Set Standby action gt gt 81 Power up action setting gt gt 87 Set Vertical zero position gt gt 489 Reboot system 491 Normal installation Inverted installation 95 Open menu 96 Stop scanning 97 Start pattern Start 1 group pattern 98 Start auto patrol Start 1 group patrol 99 Start auto scan Start 1 group scan 27 IR Intelligent Integrative Camera Installation and User Manual gt gt express that this command needs second level calling setting preset point namely it needs to call set the two preset point continuously gt gt gt express that this command need third level calling setting preset point namely it needs to call set three preset point continuously 4 On
4. EXIT gt ARE YOU SURE TO REBOOT SYSTEM CONFORNM IRIS OPEN lt OPEN gt CANCEL IRIS CLOSE lt CLOSE gt IR Intelligent Integrative Camera Installation and User Manual IR intelligent integrative camera can be rebooting remotely from the menu The operating method is open the menu and move the cursor to REBOOT and then press lt IRIS OPEN gt to enter the confirmation menu of reboot and then press lt IRIS OPEN gt again to reboot system or press lt IRIS Close gt to cancel the operation of reboot system Restore Factory Settinas DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt ENGLISH Y FACTORY SETTING gt HELP gt EXIT gt ARE YOU SURE TO RESTORE FACTORY SETTINGS CONFORNM IRIS OPEN lt OPEN gt CANCEL IRIS CLOSE lt CLOSE gt The function of restore factory settings can restore all operation that users did to the factory default settings The operating method is open the menu and move the cursor to FACTORY SETTING and Press lt IRIS OPEN gt to enter the confirmation menu of factory settings and then Press lt IRIS OPEN gt again to restart the unit and restore factory settings or press lt IRIS CLOSE gt to cancel the operation of restore factory settings 58 IR Intelligent Integration Camera Installation and User Manual Simple Trouble Shooting Table Problems No action no picture when power i
5. Punch holes and drive in four M8 setscrews As shown in the following figure Conditions of pendent mounted installation Pendent mounted unit can be used indoor in the rigid wall structure 1 The thickness of ceiling should be enough to install setscrews 2 The ceiling can withstand at least 4 times the weight of the unit Punch holes for pendent mounted bracket Take the pendent mounted bracket from the packing box and use open holes at the bottom of bracket as template and draw punch positions on the ceiling As shown in the following figure Punch holes in punch positions and drive in four M6 setscrews As shown in the following figure r Punch Positions IR Intelligent Integrative Camera Installation and User Manual Aseries of IR intelligent high speed dome camera installation A serial wall mounted structure bracket dome base E IR dome body Ct e WLAN 9 dome cover es N ING N N N N A serial pendent mounted structure ad bracket dome base LT IR dome body ts A dome cover Q 3 Installation steps of wall mounted unit 1 5 Take dome base from the packing box Pull the wire and cables out through the bracket and than aim at four open holes and fix the bracket firmly to the pre installed setscrews with four M8 nuts As shown on the left
6. and press lt IRIS OPEN gt to enter pattern setting mode The unit will automatically store horizontal and vertical rotation and camera zoom operation at this time When the recording space is filled to full or press lt IRIS OPENs the unit will stop the pattern settings 4 Delete Pattern Move the cursor to DELETE and press lt IRIS OPEN gt to delete the corresponding pattern of pattern number 54 IR Intelligent Integration Camera Installation and User Manual Timing Action Setting The timing of the unit can be divided into seven days a week ee eight periods everyday Users can set actions for every period SYSTEM INFO f nite ae DISPLAY SETUP according to the requirement When the system time is in the CAMERA SETUP 7 DOME SETUP specified period of time the unit will automatically run the preset F BEHAVIOR SETUP LANGUAGE SETUP gt ENGLISH 5 REBOOT gt action FACTORY SETTING gt HELP gt 1 Set Start Time EXIT gt Move the cursor to START TIME and press lt IRIS OPEN gt RUN SETTING to enter time input mode Please refer to the section of Date and Re roed Time Setting to input time PATROL SETTING SWEEP SETTING z PATTERN SETTING 2 Set End Time CF TIMING AC INTELLIGENT SETTING Move the cursor to END TIME and press lt IRIS OPEN gt to REGION Bae enter time input mode Please refer to the section of Date and Time Setting to input time TIMING FUNCTION SETT
7. Install the dome base onto the bracket Please refer the instruction to connect the power supply video and controlling cables Take out IR dome body from the packing box Setup communication protocol baud rate and address through SW1 and SW2 at the bottom of the IR dome body When install the IR dome body IR dome body s socket need to correspond with the dome base s socket Hold the camera with both hands aim the IR dome body s clip at the dome base s bayonet Note the corresponding red marks put the clip into bayonet slowly and then press the top of clip with a little force you can confirm the installation is set at positions after heard two crisp voice of a combined bump Note Confirm the IR dome body was completely stuck or else the IR dome body may cover off or the dome cover may be fretted Pull down the IR dome body lightly to check whether the IR dome body is completely stuck Install demo cover onto demo base and fix them Installation steps of pendent mounted unit 1 Take dome base from the packing box Pull the wire and cables out through the bracket and than aim at four open holes and fix the bracket firmly to the pre installed setscrews with four M6 nuts As shown on the left Refer to the installation steps of wall mounted unit IR Intelligent Integration Camera Installation and User Manual B series of IR intelligent high speed dome camera installation Installation steps of wall mounted unit
8. wire shorted Video Surge Arresters Communication Lightning Rod Surge Arresters Power Surge 45 degree Arresters The product must be Installed within the range of 45 degree E of lightning rod The impedance of grounded conductor can t more than 4 ohm Jacket of steel tube i i Propositional preventive maintenance The cover system of IR intelligent integration camera doesn t need any special maintenance Dust may accumulate on the inside or outside of the dome cover occasionally Should this happen please shut off the power firstly and then remove downward dome cover from dome base then clean up the dust on the dome cover by compressed air in the sprayer Warning When use the sprayer please wear appropriate eyeshade This unit includes various electrical and electronic device these devices must comply with the EU Directive 2002 96 E of Waste Electrical and Electronic Equipment WEEE to properly recycle About the recycling of this unit please contact with local supplier 60 IR Intelligent Integration Camera Installation and User Manual Serial number of the product is shown on the bottom or inside Please fill in the following blanks with mode number and serial number and properly keep this menu for checking Mode Number Serial Number CCTV SYSTEM E Part TA 11 DO6RDBMWGT 61
9. 12 OFF OFF ON ON OFF OFF OFF OFF 13 ON OFF ON ON OFF OFF OFF OFF 14 OFF ON ON ON OFF OFF OFF OFF 15 ON ON ON ON OFF OFF OFF OFF 16 OFF OFF OFF OFF ON OFF OFF OFF 17 ON OFF OFF OFF ON OFF OFF OFF 18 OFF ON OFF OFF ON OFF OFF OFF 19 ON ON OFF OFF ON OFF OFF OFF 20 OFF OFF ON OFF ON OFF OFF OFF 21 ON OFF ON OFF ON OFF OFF OFF 22 OFF ON ON OFF ON OFF OFF OFF 23 ON ON ON OFF ON OFF OFF OFF 24 OFF OFF OFF ON ON OFF OFF OFF 25 ON OFF OFF ON ON OFF OFF OFF 26 OFF ON OFF ON ON OFF OFF OFF 27 ON ON OFF ON ON OFF OFF OFF 28 OFF OFF ON ON ON OFF OFF OFF 29 ON OFF ON ON ON OFF OFF OFF 30 OFF ON ON ON ON OFF OFF OFF 31 ON ON ON ON ON OFF OFF OFF 32 OFF OFF OFF OFF OFF ON OFF OFF 17 IR Intelligent Integrative Camera Installation and User Manual SW2 PELCO D address code setting continued Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 33 ON OFF OFF OFF OFF ON OFF OFF 34 OFF ON OFF OFF OFF ON OFF OFF 35 ON ON OFF OFF OFF ON OFF OFF 36 OFF OFF ON OFF OFF ON OFF OFF 37 ON OFF ON OFF OFF ON OFF OFF 38 OFF ON ON OFF OFF ON OFF OFF 39 ON ON ON OFF OFF ON OFF OFF 40 OFF OFF OFF ON OFF ON OFF OFF 41 ON OFF OFF ON OFF ON OFF OFF 42 OFF ON OFF ON OFF ON OFF OFF 43 ON ON OFF ON OFF ON OFF OFF 44 OFF OFF ON ON OFF ON OFF OFF 45 ON OFF ON ON OFF ON OFF OFF 46 OFF ON
10. 15 minutes 30 minutes 1 ton 8 hours 12 hours and 24 hours 4 Set Sweep Direction Move the cursor to SWEEP DIR and select the direction fromA gt B and B Aby moving the joystick to left and right 53 IR Intelligent Integrative Camera Installation and User Manual Pattern setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP gt BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt RUN SETTING PRESET POINT PATROL SETTING SWEEP SETTING PATTERN SETTING TIMING AC INTELLIGENT SETTING REGION BACK gt EXIT gt PATTERN SETTING PATTERN NO SPACE AVAILABLE START REC NEW PATTERN DELETE gt RETURN gt EXIT gt ENGLISH The IR intelligent integrative camera stores a series of users operations within the specified time such as horizontal and vertical rotation camera zoom operation etc Users can review all operations that users have done by starting up the pattern The unit supports four groups of pattern each group can record 10 minutes or 500 instructions at most 1 Set Pattern Number Move the cursor to PATTERN NO and select the number by moving joystick to left and right 2 Start Pattern Move the cursor to the START and press lt IRIS OPEN gt to start the corresponding pattern of pattern number 3 Record New Pattern Move the cursor to REC NEW PATTERN
11. ON ON OFF ON OFF OFF 47 ON ON ON ON OFF ON OFF OFF 48 OFF OFF OFF OFF ON ON OFF OFF 49 ON OFF OFF OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON ON OFF OFF 54 OFF ON ON OFF ON ON OFF OFF 29 ON ON ON OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF OFF 57 ON OFF OFF ON ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF OFF 59 ON ON OFF ON ON ON OFF OFF 60 OFF OFF ON ON ON ON OFF OFF 61 ON OFF ON ON ON ON OFF OFF 62 OFF ON ON ON ON ON OFF OFF 63 ON ON ON ON ON ON OFF OFF 64 OFF OFF OFF OFF OFF OFF ON OFF 18 IR Intelligent Integration Camera Installation and User Manual SW2 PELCO D address code setting continued Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 65 ON OFF OFF OFF OFF OFF ON OFF 66 OFF ON OFF OFF OFF OFF ON OFF 67 ON ON OFF OFF OFF OFF ON OFF 68 OFF OFF ON OFF OFF OFF ON OFF 69 ON OFF ON OFF OFF OFF ON OFF 70 OFF ON ON OFF OFF OFF ON OFF 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OFF 79 ON ON ON ON OFF OFF ON OFF 80 OFF OFF OFF OFF ON OFF ON OFF 81 ON OFF OFF OFF ON OFF ON OFF 82 OFF ON OFF OFF ON OFF
12. P PATROL SETTING SWEEP SETTING PATTERN SETTING TIMING AC INTELLIGENT SETTING REGION BACK gt EXIT gt PATROL SETTING D TIME 6 SECONDS 6 SECONDS 6 SECONDS 6 SECONDS PAGE UP gt PAGE DOWN gt DEFAULT gt START gt RETURN gt Auto patrol means the unit can monitor the zone among the specified preset points the interval time can be set by users The unit supports 8 groups patrol path each patrol path supports 32 preset points in all The setting method is as follows 1 Set Patrol Number Move the cursor to PATROL NO and select the patrol number by moving the joystick to left and right 2 Edit Patrol Number Move the twinkling position to the corresponding position and press lt IRIS OPEN gt to enter the modified mode and then modify the value by moving joystick to left and right after modification is complete press lt IRIS OPEN gt to exit the modified mode Dwell time can be 1 seconds 3 seconds 6 seconds 15 seconds 30 seconds 1 minute 5 minutes 15 minutes 30 minutes 1 ton 8 hours 12 hours and 24 hours Patrol speed can be fast medium and slow You can select serial number in different page through Page Up and Page Down Each page can show four serial numbers in all move the cursor to PAGE UP or PAGE DOWN and press lt IRIS OPEN gt to page up or page down 3 Default Setting The default is the 1 to 4 preset points the default dwell time is 6 seconds and the def
13. Power Supply AC24V 2 5A NOTE Don t install the indoor unit outside Please be sure the outdoor installation meets waterproof demand IR Intelligent Integrative Camera Installation and User Manual Il Installation Guide 2 1 Preparation for Installation 1 Basic demand Before installing and using this unit please read the following warning information 1 Installation and maintenance should be carried out by professional personnel as per relative regulations All electrical work must obey the latest electrical regulations fire regulations and relevant regulations Check whether the accessories of the unit are complete according to packing list and confirm whether the place and method of installation is in accord with required if not please contact your supplier Please use this product in required environment 2 Indoor IR intelligent integrative camera designs only for indoor uses it can t be installed exposed to rain or in very humid place 3 After re installation or repair you need to measure the resistance between the circuit and shell to check whether the insulation is good and ensure there is no short circuit between the circuit and shell 4 Confirm there is enough place to contain the product and its structure components Confirm the ceiling wall and bracket for installation can take the total weight of the product and its structure components and materials used to support the weigh
14. address code setting Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF ON ON OFF OFF OFF OFF OFF 8 ON ON ON OFF OFF OFF OFF OFF 9 OFF OFF OFF ON OFF OFF OFF OFF 10 ON OFF OFF ON OFF OFF OFF OFF 11 OFF ON OFF ON OFF OFF OFF OFF 12 ON ON OFF ON OFF OFF OFF OFF 13 OFF OFF ON ON OFF OFF OFF OFF 14 ON OFF ON ON OFF OFF OFF OFF 15 OFF ON ON ON OFF OFF OFF OFF 16 ON ON ON ON OFF OFF OFF OFF 17 OFF OFF OFF OFF ON OFF OFF OFF 18 ON OFF OFF OFF ON OFF OFF OFF 19 OFF ON OFF OFF ON OFF OFF OFF 20 ON ON OFF OFF ON OFF OFF OFF 21 OFF OFF ON OFF ON OFF OFF OFF 22 ON OFF ON OFF ON OFF OFF OFF 23 OFF ON ON OFF ON OFF OFF OFF 24 ON ON ON OFF ON OFF OFF OFF 25 OFF OFF OFF ON ON OFF OFF OFF 26 ON OFF OFF ON ON OFF OFF OFF 27 OFF ON OFF ON ON OFF OFF OFF 28 ON ON OFF ON ON OFF OFF OFF 29 OFF OFF ON ON ON OFF OFF OFF 30 ON OFF ON ON ON OFF OFF OFF 31 OFF ON ON ON ON OFF OFF OFF 32 ON ON ON ON ON OFF OFF OFF
15. from the menu the method to set parameters specific meanings and settings are as follows this function needs support by camera 1 Focus Mode System default is automatic Auto focus function allows lens keeps focus during using magnified contractible and mobile function If focus mode is set to AUTO camera will auto focus when the unit rotates and zooms If focus mode is set to MANUAL then adjust focus manually Press lt FAR gt or lt NEAR gt button on the keyboard to adjust focal length If focus mode is set to Once focus only once after zoomed and no focus next time unless reset focus Focus mode includes auto focus manual focus and once focus The setting method is move the cursor to FOCUS MODE and select option by moving the joystick to left and right 2 Digital Zoom System default is close Close and open the camera digital zoom function from the menu Setting method is move the cursor to D ZOOM and then select open or close option by moving the joystick to left and right 3 Back Light Compensation System default is closed The backlight compensation is that when the brightness of the image center is relative low you can open backlight compensation function to improve the brightness of the image You can open and close the backlight compensation function from the menu The Setting method is move cursor to BLC and select open or close option by moving the joystick to left and right 4 ICR Mode Syst
16. menu 4 If move the cursor to CANCEL and press lt IRIS OPEN gt will cancel the title modification and return to the previous menu 45 Dome Advanced Setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH DOME SETTING POWER UP AC STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING CALL PRESET POINT 1 CS ADVANCE SETTING RETURN gt EXIT gt ADVANCE SETTING AUTO FLIP OPEN REDUCE SPEED OPEN IMAGE FREEZE CTRL DIR MODE SOFT ADDRESS AZIMUTH SETTING MASK SETTING VIDEO SYNC COMM TESTING RETURN gt EXIT gt NORMAL IR Intelligent Integrative Camera Installation and User Manual 1 Auto Flip System default is open When the lens runs vertically to 90 if user keeps pressing the joystick the lens will automatically flip 180 horizontally thus consecutive monitoring of moving object can be realized The setting method is move the cursor to AUTO FLIP and select open or close option by moving the joystick to left and right 2 Reduce Speed System default is open The setting method is move the cursor to REDUCE SPEED and select open or close option by moving the joystick to left and right 3 Image freeze System default is close Image freeze means whether fre
17. method to set display state Move cursor to the required position select display state by moving joystick to left and right Display items can be placed anywhere on the monitor This function is used to set user defined interface The following positions of the display items can be adjusted Dome Title Preset Position Date amp Time Azimuth Region Zoom Display The method to adjust the position of display items move the cursor to DISPLAY SETUP and press lt IRIS OPEN to enter the menu of display position setting and then users can adjust to proper position by moving the joystick to left right up and down Note different display items positions can t overlap otherwise the characters on the screen will be covered press lt IRIS OPEN after adjustment Move the cursor to RETURN or EXIT and press lt IRIS OPEN gt to save setting and return to previous menu or exit menu 36 Camera Setup DOME MENU SYSTEM INFO DISPLAY SETUP lt P CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH CMAERA SETTING ZOOM SPEED WIDE DYNAMIC V FLIP MIRROR ADVANCE RETURN gt EXIT gt RED GAIN BLUE GAIN AE MODE BRIGHT IRIS SHUTTER GAIN ANTISHOCK RETURN gt EXIT gt IR Intelligent Integration Camera Installation and User Manual The unit allows users to adjust parameters of camera
18. number by moving the joystick to left and right The unit supports RUN SETTING CP PRESET POINT 204 preset points totally 1 to 48 and 100 to 255 PATROL SETTING y 2 E SWEEP SETTING 2 Preset points Title Setting PATTERN SETTING TIMING AC Move the cursor to TITLE SETTING and press lt IRIS INTELLIGENT SETTING Bike OPENs gt to enter the submenu of preset position title setting and EXIT gt then set preset position title See the section of Title Setting for BRESEV SETTING more information of setting Cy PRESET NO 001 3 Call Preset points TITLE SETTING gt 01 Ta Move the cursor to CALL and press lt IRIS OPEN gt to call DELETE 2 RETURN gt the corresponding preset scene of preset points number EXIT gt 4 Set Preset points Move the cursor to SET and press lt IRIS OPEN gt to enter preset points setting mode at this time user can operate the unit When the unit reaches the expected preset scene press lt IRIS OPEN gt to store the current position 5 Delete Preset points Move the cursor to DELETE and press lt IRIS OPEN gt to delete the corresponding preset scene of preset points number 51 IR Intelligent Integrative Camera Installation and User Manual Auto Patrol Setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP 7 BEHAVIOR SETUP LANGUAGE SETUP gt ENGLISH REBOOT gt FACTORY SETTING gt HELP gt EXIT gt RUN SETTING I lt
19. old password before you input a new password The initial password of the unit is 000000 Password input please refers to the section of Date and Time Setting 42 IR Intelligent Integration Camera Installation and User Manual Alarm Setting The unit has 8 channels alarm input 2 channels alarm output alarm function need to select alarm module After received the DOME MENU alarm alarm input signal can trigger user defined action iestedieo gt OTE meanwhile cause specified alarm output Alarm function setting DISPLAY SETUP method is as follows GAMERA SETUR 1 Alarm Function gt DOME SETUP n BEHAVIOR SETUP You can open or close the alarm function The Setting LANGUAGE SETUP gt ENGLISH method is move the cursor to ALARM EN and select open or REBOOT gt r A x z FACTORY SETTING gt closed option by moving the joystick to left and right HELP gt 2 Alarm Number oi Move the cursor to ALARM NO and select alarm input channel by moving the joystick to left and right total support eight DOME SETTING alarm input channels After Alarm number changed the system aie ee get T will automatically refresh associated setting items to display the POWER UP AC CALL PRESET POINT 1 STANDBY SETTING corresponding data DATA amp TIME SETTING 3 Input Type Seung E Move the cursor to AUX TYPE and select input type by IR SETTING moving the joystick to left and right Alarm input type can be set to F DVAN
20. to high medium and low The setting method is move the cursor to IR LED BRIGHT and select options by moving the joystick to left and right 3 On Time You can control the opening time of the IR LED only when the IR control mode is set to timing mode About how to input on time please refer to the section of Date and Time setting 4 Off Time You can control the closing time of the IR LED only when the IR control mode is set to timing mode About how to input off time please refer to the section of Date and Time setting 5 Far Near Mode System default is medium You can adjust the camera s multiple of far near lamp The multiple values including high medium and low The setting method is move the cursor to FAR amp NEAR MODE and select options by moving the joystick to left and right 6 Threshold System default is medium When IR lamp control mode is set to automatic the sensitivity of brightness can be set to high medium and low The setting method is move the cursor to THRESHOLD and select options by moving the joystick to left and right 7 Scan Interval System default is 15 seconds You can control the interval time of detecting the ambient light Options are 1 seconds 3 seconds 6 seconds 15 seconds 30 seconds 1 minute and 5 minutes The setting method is move the cursor to SCAN INTERVAL and select options by moving the joystick to left and right 44 IR Intelligent Integration Camera Installat
21. 6 and preset point No 1 to start the first group of auto scan Note The more level the higher speed Horizontal sweep 1 The method to set speed of sweep is Set preset point No 66 and set sweep preset point number table 1 and set sweep preset point speed number table 2 29 IR Intelligent Integrative Camera Installation and User Manual Table 1 Sweep preset point number 1 2 3 4 5 Preset point 11 21 12 22 13 23 14 24 15 25 A gt B Sweep preset point number 6 7 8 9 10 direction Preset point 16 26 17 27 18 28 19 29 20 30 Sweep preset point number 11 12 13 14 15 Preset point 21 11 22 12 23 13 24 14 25 15 B gt A Sweep preset point number 16 17 18 19 20 direction Preset point 26 16 27 17 28 18 29 19 30 20 Table 2 Sweep preset point speed number 1 2 3 Sweep speed low medium high E g Set preset point No 66 and set sweep preset point No 1 and set sweep preset point speed No 3 to set the first horizontal sweep to high speed mode Expert mode setting In order to avoid users operate special functions of preset point these special functions have been blocked in factory default setting if users need to use these functions please open Expert mode The method is 1 Open Expert mode Set preset point No 72 to open Expert mode 2 Close Expert mode Call preset point No 72 to close Expert mode Open and close Expert model only need one time to take
22. B serial wall mounted structure 1 Take IR dome camera from packing box set up dome i camera protocol baud rate and address Pull the wire and racket ky cable out through the bracket and then aim at four open holes on the bracket and fix the IR dome camera firmly to jji bracket with M6 socket head screws which are along with the IR dome camera JOD unit As shown on the left 7 2 Aim at four open holes on the wall and fix the bracket firmly to oy the pre installed setscrews with four M8 nuts S A 3 Please refer to the instruction to connect the power supply video and controlling cables Installation steps of pendent mounted unit 1 Take IR dome camera from the packing box setup B serial pendent mounted structure communication protocol baud rate and address through SW1 and SW2 at the bottom of the IR dome camera Pull the wire bracket and cable out through the bracket and then aim at four open holes on the bracket and fix the IR dome camera firmly to the bracket with M6 screws As shown on the left IR dome camera ar F 7 PrN 2 Aim at four open hole on the ceiling and fix the bracket firmly to the pre installed setscrews with four M6 nuts 3 Please refer to the instruction to connect the power supply video and controlling cables IR Intelligent Integrative Camera Installation and User Manual C series of IR intellige
23. ERA SETUP gt DOME SETUP screen and the number of data packet sent from test software BEHAVIOR SETUP a SETUPS ENGLISH the number of data packet received and the reliability of FACTORY SETTING gt n F e A x m HELP gt communication lines will be shown in the window EXIT gt software the window such as the left picture will be shown on the DOME SETTING POWER UP AC CALL PRESET POINT 1 STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt ADVANCE SETTING AUTO FLIP REDUCE SPEED IMAGE FREEZE CTRL DIR MODE NORMAL SOFT ADDRESS AZIMUTH SETTING MASK SETTING VIDEO SYNC Y COMM TESTING RETURN gt EXIT gt COMM TESTING DATAPAGE T R 100 100 RELIABILITY 100 Y RETURN gt EXIT gt 50 IR Intelligent Integration Camera Installation and User Manual Preset Point Setting The IR Intelligent Integrative Camera stores horizontal and DOME MENU vertical coordinate and information of camera zoom Users can SYSTEM INFO quickly orientate the camera to the wanted testing scene The unit DISPLAY SETUP CAMERA SETUP DONE SETUP supports 204 preset posints totally The method to set Preset 9 BEHAVIOR SETUP 7 4 LANGUAGE SETUP gt ENGLISH points is as follows REBOOT gt iey SENG 1 Preset points Number Setting EXIT gt Move the cursor to PRESET NO and set preset point
24. GE Seen normally open type or normally closed type RETURN gt Normally open type when channel is closed it means system has EI received effective warning signs Normally closed type when channel is open it means system has received effective warning signs 4 Alarm Mode Al ee F Alarm mode includes automatic timing and manually Move UKINE ormattyopen the cursor to the ALARM MODE and select mode by moving the ALARM MODE AOTU joystick to left and right ALARM OUT OUTPUT 1 amp 2 ALARM AC CALL PRESET POSTION 1 5 Alarm output KEEP TIME 15 SECONDS Move the cursor to ALARM OUT and select the output type START SCHEDULE 00 00 ENO SCHEDUE aan by moving the joystick to left and right The types use to set CONFIRM gt whether to link the alarm switch when system receives effective RETURNS alarm input signal The type can be set to close output 1 output 2 and output 1 amp 2 6 Alarm Action Move the cursor to ALARM AC and press lt IRIS OPEN gt to set alarm action This function used to set whether link to some preset special functions such as preset position patrol path pattern sweep etc when the current channel alarm 7 Keep Time Move the cursor to KEEP TIME press lt IRIS OPEN gt to set keep time When the current channel alarm occurs if link to alarm output alarm output switch will be closed alarm keep time is the time between detecting alarm signals and removing the alarm alarm output sw
25. ING 3 Set Timer Action CF TIMER NO 1 START TIME doto The linked action of each period can be set as follows 18 END TIME 00 00 TIMER ACTION NO ACTION kinds of actions in all SCHEDULE SETTING RERAN No action Call preset points No 1 to No 8 TIMER SCHEDULE SETTING a k Start the first or the second preset points patrol 7 MONDAY TUESDAY Start the first or the second horizontal sweep WEDNESDAY THURSDAY i FRIDAY Start the first or the fifth auto scan SATURDAY SUNDAY Start the first or the second mode path DEFAULT gt RETURN gt Start auto tracking 4 Set Schedule Move the cursor to SCHEDULE SETTING and press lt IRIS OPENs gt to enter timer schedule setting Note Different periods can t overlap and the period can t span 00 00 If users operate the unit during timing period the timer action will be interrupted If there is no action within the specified time and the current time is still in timing period the timer action will be executed again 55 IR Intelligent Integrative Camera Installation and User Manual Auto Track Setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP lt P BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH RUN SETTING PRESET POINT PATROL SETTING SWEEP SETTING PATTERN SETTING TIMING AC CF INTELLIGENT SETTING REGION BACK gt EXIT
26. IR Intelligent Integrative Camera Installation and User s manual English V3 01 Hu AA AD Please read the manual carefully before installing and using the unit Catalogue WIC ONN a CEASE SEST SETTAT veasie vous sasisennsei an esbeesisbens ss TEE 1 l Important Safeguards 1 1 34 0t 0ttitetcteicten tet thet eens 2 li installation Gude e ettette t et ee atoae ee etaendencevetivedes 4 2 1 Preparation for Installation eee ce eeeeeeeneeeeeeneeeeseeeeneeeesaeeeeaees 4 2 2 Installation A020 e ee ae a ee eee 5 III Description Of Functions sssessessssrssressrrsesrrrsrrnerrnnrrnnrennnrnnnrnnnsenne 12 3 1 Performance Characteristic cc eeeceeeeeeeeeeeeeeeeeeeeeneeeeeneeeeeeeees 12 3 2 F et md cl rat OT sscicsciciesckensvesevssiteesteareaaevesctenstasdevusien dinette 13 IV Technical parameter sssessseessessrresrnsrrnnsrnnsrrnetrnntrnnsrnnsrnnetnnnnsennnena 26 5 1 Common function quick instruction list 27 5 2 Menu operation guide s essssssseesreesrissrnssrnrsrrnntrnnttnnennsenantnnntnenne 33 Simple Trouble Shooting Table ssesssesssesisserirssrrsrrnsrrnnrrnnrrrnsrrnsrrnneenne 59 Lightning and Surge Protection ccccccecceceeeeeeeeeeeeeeeeeeeeeeeseeeeeseeeeeeeees 60 Propositional preventive maintenance eeeeeeeeeeeeeeeeeeteeeteneeeeseeeeaees 60 IR In
27. N ON OFF 118 OFF ON ON OFF ON ON ON OFF 119 ON ON ON OFF ON ON ON OFF 120 OFF OFF OFF ON ON ON ON OFF 121 ON OFF OFF ON ON ON ON OFF 122 OFF ON OFF ON ON ON ON OFF 123 ON ON OFF ON ON ON ON OFF 124 OFF OFF ON ON ON ON ON OFF 125 ON OFF ON ON ON ON ON OFF 126 OFF ON ON ON ON ON ON OFF 127 ON ON ON ON ON ON ON OFF 128 OFF OFF OFF OFF OFF OFF OFF ON 20 IR Intelligent Integration Camera Installation and User Manual SW2 PELCO D address code setting continued Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 129 ON OFF OFF OFF OFF OFF OFF ON 130 OFF ON OFF OFF OFF OFF OFF ON 131 ON ON OFF OFF OFF OFF OFF ON 132 OFF OFF ON OFF OFF OFF OFF ON 133 ON OFF ON OFF OFF OFF OFF ON 134 OFF ON ON OFF OFF OFF OFF ON 135 ON ON ON OFF OFF OFF OFF ON 136 OFF OFF OFF ON OFF OFF OFF ON 137 ON OFF OFF ON OFF OFF OFF ON 138 OFF ON OFF ON OFF OFF OFF ON 139 ON ON OFF ON OFF OFF OFF ON 140 OFF OFF ON ON OFF OFF OFF ON 141 ON OFF ON ON OFF OFF OFF ON 142 OFF ON ON ON OFF OFF OFF ON 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON OFF ON OFF OFF ON 150 OFF ON ON OFF ON OFF OFF ON 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF
28. NG ZOOM SPEED WIDE DYNAMIC V FLIP MIRROR lt P ADVANCE RETURN gt EXIT gt CAMERA ADVANCE CF WB MODE RED GAIN BLUE GAIN AE MODE BRIGHT IRIS SHUTTER GAIN ANTISHOCK RETURN gt EXIT gt Setting method is as follows note this function needs support by camera 1 White Balance System default is automatic You can change white balance mode from menu so that the most effective and real color image can be got in full ambient light The white balance model includes Auto Manual Indoor Outdoor Auto tracking and single white balance Note Different camera may have different write balance options The setting method is move the cursor to WB MODE and then select the option you wanted by moving the joystick to left and right 2 Red Gain Red gain is the gain of red components Users can adjust red gain value according to the actual situation only when white balance is in manual mode this setting can be effective The setting method is move the cursor to RED GAIN and then adjust red gain value by moving the joystick to left and right 3 Blue Gain Blue gain is the gain of blue components Users can adjust blue gain value according to the actual situation only when white balance is in manual mode this setting can be effective The setting method is move the cursor to BLUE GAIN and then adjust blue gain value by moving the joystick to left and right 4 Exposure Mode System default is automat
29. OFF ON ON ON ON OFF ON 189 ON OFF ON ON ON ON OFF ON 190 OFF ON ON ON ON ON OFF ON 191 ON ON ON ON ON ON OFF ON 192 OFF OFF OFF OFF OFF OFF ON ON 22 IR Intelligent Integration Camera Installation and User Manual SW2 PELCO D address code setting continued Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 193 ON OFF OFF OFF OFF OFF ON ON 194 OFF ON OFF OFF OFF OFF ON ON 195 ON ON OFF OFF OFF OFF ON ON 196 OFF OFF ON OFF OFF OFF ON ON 197 ON OFF ON OFF OFF OFF ON ON 198 OFF ON ON OFF OFF OFF ON ON 199 ON ON ON OFF OFF OFF ON ON 200 OFF OFF OFF ON OFF OFF ON ON 201 ON OFF OFF ON OFF OFF ON ON 202 OFF ON OFF ON OFF OFF ON ON 203 ON ON OFF ON OFF OFF ON ON 204 OFF OFF ON ON OFF OFF ON ON 205 ON OFF ON ON OFF OFF ON ON 206 OFF ON ON ON OFF OFF ON ON 207 ON ON ON ON OFF OFF ON ON 208 OFF OFF OFF OFF ON OFF ON ON 209 ON OFF OFF OFF ON OFF ON ON 210 OFF ON OFF OFF ON OFF ON ON 211 ON ON OFF OFF ON OFF ON ON 212 OFF OFF ON OFF ON OFF ON ON 213 ON OFF ON OFF ON OFF ON ON 214 OFF ON ON OFF ON OFF ON ON 215 ON ON ON OFF ON OFF ON ON 216 OFF OFF OFF ON ON OFF ON ON 217 ON OFF OFF ON ON OFF ON ON 218 OFF ON OFF ON ON OFF ON ON 219 ON ON OFF ON ON OFF ON ON 220 OFF OFF ON ON ON OFF ON ON 221 ON OFF ON ON ON OFF ON ON 222 OFF ON ON ON ON OFF ON ON 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON
30. ON OFF 83 ON ON OFF OFF ON OFF ON OFF 84 OFF OFF ON OFF ON OFF ON OFF 85 ON OFF ON OFF ON OFF ON OFF 86 OFF ON ON OFF ON OFF ON OFF 87 ON ON ON OFF ON OFF ON OFF 88 OFF OFF OFF ON ON OFF ON OFF 89 ON OFF OFF ON ON OFF ON OFF 90 OFF ON OFF ON ON OFF ON OFF 91 ON ON OFF ON ON OFF ON OFF 92 OFF OFF ON ON ON OFF ON OFF 93 ON OFF ON ON ON OFF ON OFF 94 OFF ON ON ON ON OFF ON OFF 95 ON ON ON ON ON OFF ON OFF 96 OFF OFF OFF OFF OFF ON ON OFF 19 IR Intelligent Integrative Camera Installation and User Manual SW2 PELCO D address code setting continued Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 97 ON OFF OFF OFF OFF ON ON OFF 98 OFF ON OFF OFF OFF ON ON OFF 99 ON ON OFF OFF OFF ON ON OFF 100 OFF OFF ON OFF OFF ON ON OFF 101 ON OFF ON OFF OFF ON ON OFF 102 OFF ON ON OFF OFF ON ON OFF 103 ON ON ON OFF OFF ON ON OFF 104 OFF OFF OFF ON OFF ON ON OFF 105 ON OFF OFF ON OFF ON ON OFF 106 OFF ON OFF ON OFF ON ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 111 ON ON ON ON OFF ON ON OFF 112 OFF OFF OFF OFF ON ON ON OFF 113 ON OFF OFF OFF ON ON ON OFF 114 OFF ON OFF OFF ON ON ON OFF 115 ON ON OFF OFF ON ON ON OFF 116 OFF OFF ON OFF ON ON ON OFF 117 ON OFF ON OFF ON O
31. ON ON 23 IR Intelligent Integrative Camera Installation and User Manual SW2 PELCO D address code setting continued Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON 231 ON ON ON OFF OFF ON ON ON 232 OFF OFF OFF ON OFF ON ON ON 233 ON OFF OFF ON OFF ON ON ON 234 OFF ON OFF ON OFF ON ON ON 235 ON ON OFF ON OFF ON ON ON 236 OFF OFF ON ON OFF ON ON ON 237 ON OFF ON ON OFF ON ON ON 238 OFF ON ON ON OFF ON ON ON 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 243 ON ON OFF OFF ON ON ON ON 244 OFF OFF ON OFF ON ON ON ON 245 ON OFF ON OFF ON ON ON ON 246 OFF ON ON OFF ON ON ON ON 247 ON ON ON OFF ON ON ON ON 248 OFF OFF OFF ON ON ON ON ON 249 ON OFF OFF ON ON ON ON ON 250 OFF ON OFF ON ON ON ON ON 251 ON ON OFF ON ON ON ON ON 252 OFF OFF ON ON ON ON ON ON 253 ON OFF ON ON ON ON ON ON 254 OFF ON ON ON ON ON ON ON 255 ON ON ON ON ON ON ON ON 24 IR Intelligent Integration Camera Installation and User Manual The following is PELCO P protocol address coding table SW2 PELCO P
32. ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF ON 159 ON ON ON ON ON OFF OFF ON 160 OFF OFF OFF OFF OFF ON OFF ON 21 IR Intelligent Integrative Camera Installation and User Manual SW2 PELCO D address code setting continued Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 161 ON OFF OFF OFF OFF ON OFF ON 162 OFF ON OFF OFF OFF ON OFF ON 163 ON ON OFF OFF OFF ON OFF ON 164 OFF OFF ON OFF OFF ON OFF ON 165 ON OFF ON OFF OFF ON OFF ON 166 OFF ON ON OFF OFF ON OFF ON 167 ON ON ON OFF OFF ON OFF ON 168 OFF OFF OFF ON OFF ON OFF ON 169 ON OFF OFF ON OFF ON OFF ON 170 OFF ON OFF ON OFF ON OFF ON 171 ON ON OFF ON OFF ON OFF ON 172 OFF OFF ON ON OFF ON OFF ON 173 ON OFF ON ON OFF ON OFF ON 174 OFF ON ON ON OFF ON OFF ON 175 ON ON ON ON OFF ON OFF ON 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON OFF OFF ON ON OFF ON 179 ON ON OFF OFF ON ON OFF ON 180 OFF OFF ON OFF ON ON OFF ON 181 ON OFF ON OFF ON ON OFF ON 182 OFF ON ON OFF ON ON OFF ON 183 ON ON ON OFF ON ON OFF ON 184 OFF OFF OFF ON ON ON OFF ON 185 ON OFF OFF ON ON ON OFF ON 186 OFF ON OFF ON ON ON OFF ON 187 ON ON OFF ON ON ON OFF ON 188 OFF
33. PELCO D amp 2400BPS PELCO P amp 9600BPS 1 Protocol setting Protocol SW1 1 SW1 2 SW1 3 Auto identification or PELCO D OFF OFF OFF TAO1 OFF OFF ON PELCO P ON OFF OFF GA Industry agreement ON OFF ON Eccer a ee 2 Baud rate setting Baud rate SW1 4 SW1 5 Auto identification or 1200bps OFF OFF 2400bps ON OFF 4800bps OFF ON 9600bps ON ON 3 Address setting SW2 toggle switch used to set address of the unit Address sitting is used binary system the eighth bit is the highest bit and the first bit is the lowest bit The broadcast address is No 0 which means if only the address of control port is No 0 the units which have suited protocol and baud rate can be controlled 16 IR Intelligent Integration Camera Installation and User Manual The following is the protocol address coding table of PELCO D TAO1 SW2 PELCO D address code setting Address code SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF 10 OFF ON OFF ON OFF OFF OFF OFF 11 ON ON OFF ON OFF OFF OFF OFF
34. TTING IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt RUN SETTING PRESET POINT PATROL SETTING SWEEP SETTING PATTERN SETTING TIMING AC INTELLIGENT SETTING REGION BACK gt EXIT gt IR Intelligent Integration Camera Installation and User Manual System Information Users can check system information through the menu of the DOME MENU IR intelligent integration camera system information includes the CHISYSTEM INFO version of the unit protocol of the unit communication speed DISPLAY SETUP CAMERA SETUP k F A DOME SETUP address of the unit serial number of the unit system date title of BEHAVIOR SETUP nea ENGLISH the unit temperature of the unit language system temperature FACTORY SETTING gt gt HELP gt unit etc EXIT gt Check system information as follows NIELLIGENT HIGHSPEED DOME Move the cursor to SYSTEM INFO and press lt IRIS VERSION OPEN gt enter system information menu and check system PROTOCOL AUTO IDENTIFICATION BAUDRATE 2400 N 8 1 ADDRESS 3 information The system support Fahrenheit and Celsius two SN HP20110203001 F ba ae x DATE 2011 04 01 temperature unit and the default temperature unit is Celsius The TITLE INTELLIGENT HIGH SPEED DEMO 7 OTHERS RETURN gt EXIT gt method to change the temperature unit is move the cursor to TEMPERATURE UNIT and select unit by moving the joystick to left and r
35. ation protocols No internally saved data lose when power off In build module contains surge immunity protection 204 preset positions for free storage precise positioning and have preset screen freeze function Programmable automatic patrolling tracks automatic sweep function and guarding function Supports remote fault diagnosis system upgrade reset and address setting function HF gt Automatically identify different camera modules communication protocol and baud rate Optional Multi language function and also achieve date temperature angle and compass display Optional timing function Integrated high speed PTZ Integrated design compact structure high reliability Precise motor drive infinite variable speed steady operation no jitter sensitive control N Achieve automatically flip 180 and consecutive monitoring vertically Low power consumption calorific value is only half of the similar manufacturer s products 12 IR Intelligent Integration Camera Installation and User Manual Built in HD integrative camera Auto iris auto backlighting compensation Auto manual white balance t Auto manual focus Automatic brightness control HD integrative camera Multiple zoom integrative camera can be chosen 24 hour outdoor design Built in heaters sensors intelligent control Built in radiator fan which makes the unit can work at high temperature ambient condition 60 C T
36. aud rate and address through SW1 a and SW2 at the bottom of the IR dome body Pull the wire and la cable out through the bracket and then aim at four installed holes on the ceiling and fix the IR dome camera firmly to bracket with M6 screws As shown on the left AL A 2 Aim at four installing hole on the ceiling and fix the bracket IR dome camera firmly to the pre installed setscrews with four M6 nuts 3 Please refer to the instruction to connect the power supply video and controlling cables Note The pendent mounted bracket can not be used outside Because of this specialized operation condition please ensure that this dome camera meet the waterproof demand 1 The suspender which is used with the pendent mounted bracket must meet waterproof demand otherwise the customer will be responsible for the water fault 2 Its forbidden to pull the leading out wire of the unit out through the Flange side hole of the pendent mounted bracket 3 Make sure the sealing ring and Flange sunken hole of pendent mounted bracket are tightly combined and sealed from water 4 Put silica gel around Flange of pendent mounted bracket to seal from water 5 Put silica gel around the connector of pendent sleeve and upper shield to seal from water 6 All exposed screw holes of pendent mounted bracket must be played silica gel to seal from water 11 IR Intelligent Integrative Camera Installation and User Manual lll Descripti
37. ault speed is fast 4 Start Patrol Move the cursor to START and press lt IRIS OPEN to start the corresponding auto patrol 52 IR Intelligent Integration Camera Installation and User Manual Horizontal Sweep Settings DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP CP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH RUN SETTING PRESET POINT PATROL SETTING CP SWEEP SETTING PATTERN SETTING TIMING AC INTELLIGENT SETTING REGION BACK gt EXIT gt SWEEP SETTING C SWEEP NO START POS END POS SWEEP SPEED D TIME SWEEP DIR START gt RETURN gt 1 SECOND A gt B Horizontal sweep means that the unit scans back and forth between two specified horizontal preset points and the scanning speed and scanning direction can be set by users 1 Set Sweep Number Move the cursor to SWEEP NO and select sweep number by moving joystick to left and right Optional sweep number is from 1 to 20 2 Set Sweep Speed System default is medium Move the cursor to SWEEP SPEED and select the speed by moving the joystick to left and right Options of sweep speed fast medium slow 3 Set Dwell Time System default is 1 second Move the cursor to D TIME and select the time by moving the joystick to left and right Options of dwell time 1 second 3 seconds 6 seconds 15 seconds 30 seconds 1 minute 5 minutes
38. c Gas Discharge Tube and TVS class lightning protection technology to effectively prevent such pulse signal damage caused by instantaneous lightning under 3KW or electric surge But for outdoor installing on the premise of ensuring electric safety necessary protective measures should be taken according to practical situation e Signal transmission lines must be kept at least 50 meters from high voltage equipment and high voltage For outside please select the place under eaves to layout the routing For open field you must use underground sealed steel tube and the steel tube must be adopted one point grounding mode and absolutely forbid adopted overhead wiring e In intense thunderstorms or high induced voltage areas such as high voltage substations must use extra high power lightning protection equipment and install lightning rod and others measures e The lightning protection and grounded design for outdoor installation and wiring must be combined with requirements of building s lightening prevention and comply with the relevant national standards and industry standards e The system must be equipotential grounding Grounded device must meet double requirements of system anti jamming and electrical safety and can t be short circuited or hybrid circuited with neutral leg of forceful electric power When system grounded alone the impedance of grounded conductor can t more than 4 ohm sectional area of grounded wire can t more than 25mm
39. cursor to CONFIRM and press lt IRIS OPEN gt to save modification and return to the previous menu 3 Cancel Move the cursor to CANCEL and press lt IRIS OPEN gt to cancel modification and return to the previous menu 41 Password Setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP Cy DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH DOME SETTING POWER UP AC STANDBY SETTING DATA amp TIME SETTING CALL PRESET POINT 1 PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt PASSWORD SETTING 7 PASSWORD EN PASSWORD SETTING CONFIRM gt RETURN gt IR Intelligent Integrative Camera Installation and User Manual You can restrict users without permissions to modify the system settings through password protection function of the unit If you open the password protection function you need to input correct password to open the menu The method to enable and modify password is as follows 1 Password Enable Move the cursor to PASSWORD EN and select open or close password protection by moving the joystick to left and right When the password protection function is open you need to input correct password to open the menu 2 Modify passwords Move the cursor to PASSWORD SETTING and press lt IRIS open gt to enter the password setting mode You need to input
40. e action setting Set standby time Set preset point No 80 and then set preset point number of time to set idle time system default is 30 seconds Preset point number of 1 2 3 4 5 6 T time Time 15 sec 30 sec 1 min 5 min Preset point number 8 9 10 11 12 13 14 Time 15 30 min ihour 8 hours 12 hours 24 hours reserve Set standby action Set preset points No 80 and then set preset points of action to set idle action system default is no action E g call preset point No 80 and then call preset point of action No 10 to set standby action to the 1 preset point patrol Power up action system default call the first presets Set power up action Set preset point No 81 and then set preset point of action to set the power up action E g set power up action to call preset point No 1 You can call preset point No 81 and then call preset point of action No 2 to call preset point No 1 after power up Reboot the system The unit allows user to reboot the system remotely by a special command The method is call preset point No 89 to reboot the system Automatic identification camera setting The method is call preset point No 49 and then call preset point No 17 and then select automatic identification cameras mode 31 IR Intelligent Integrative Camera Installation and User Manual IR setting The method is call preset point No 49 and then call preset point number N Firs
41. effect immediately The state of expert model will be saved even power off before you change Expert mode next time you don t need to open Expert mode every time when you operate the special functions The items with4in common commands table only can be operated when expert mode is open if you need to restart the unit and the expert mode is already open please directly call preset point NO 89 to restart the unit if the expert mode is close set preset point No 72 to open expert mode firstly and then call preset point No 89 to restart the unit Delete all preset positions You can quickly delete all preset points with one key The method is Call preset points No 71 to delete all preset points 30 IR Intelligent Integration Camera Installation and User Manual Restore factory settings The restore factory settings function can restore all operations to factory default settings The method is Call preset point No 79 to restore all settings to factory default settings Vertical zero position setting system default is low position This function can adjust zero position in vertical direction The method is Call preset point No 87 and then call the corresponding preset point number of vertical direction Vertical zero position in high position means the unit can monitor farther view under normally installation Preset points of vertical direction 1 2 3 zero position High Medium Low Standby standby or idl
42. em default is automatic Set color of the camera from the menu options Auto Color Black and White The setting method is move the cursor to ICR and then select ICR mode by moving the joystick to left and right 5 Zoom Speed System default is medium speed Set dome camera s default zoom speed from the menu Zoom speed can be set to low medium and high The setting method is move the cursor to ZOOM SPEED and select the needed zoom speed by moving the joystick to left and right 6 Wide Dynamic System default is close Wide dynamic function can improve the image quality and get clear image in the stronger contrast light condition Wide dynamic mode can be set to close low medium and high The setting method is move the cursor to WIDE DYNAMIC and select the needed mode by moving the joystick to left and right 7 Flip System default is close The setting method is move the cursor to V FLIP and select open or close option by moving the joystick to left and right 8 Mirror System default is close The setting method is move the cursor to MIRROR and select open or close option by moving the joystick left and right 37 IR Intelligent Integrative Camera Installation and User Manual Camera Advanced Setting DOME MENU SYSTEM INFO DISPLAY SETUP F CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH CMAERA SETTI
43. et to close x1 to x10 The setting method is move the cursor to ZOOM TRACK and select options by moving the joystick to left and right 4 Return Time In the menu of auto track setting users can set and delete the return time which the unit needs to wait after the moving target disappears from the monitoring area Return time can set to 3 seconds 6 seconds 15 seconds and 30 seconds 5 Space Setting In the menu of space setting users can set and delete the scene which the unit needs to return after the moving target disappears from the monitoring area 56 IR Intelligent Integration Camera Installation and User Manual Region Indication Setting DISPLAY SETUP CAMERA SETUP DOME SETUP CP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt RUN SETTING PRESET POINT PATROL SETTING SWEEP SETTING PATTERN SETTING TIMING AC INTELLIGENT SETTING CF REGION BACK gt EXIT gt REGION SETTING CP REGION NO REGION TITLE gt LEFT VERGE gt RIGHT VERGE gt DELETE gt RETURN gt EXIT gt Region indication means that when users move the unit into the range of the specified preset region by operating the joystick the screen will display the title of this preset region so that users can indentify different regions conveniently The unit supports eight region indications Users can start up the function of region indication only when the lef
44. eze current image when call the preset position The setting method is move the cursor to IMAGE FREEZE and select open or close option by moving the joystick to left and right 4 Control direction Mode System default is normal Installation style includes normal and inversion When inversed installation pictures and operating will auto adjust to match with the inverted installation The setting method is move the cursor to CTRL DIR MODE and select normal or inversed option by moving the joystick to left and right 46 Soft address settings DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP F DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH DOME SETTING POWER UP AC CALL PRESET POINT 1 STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING Y ADVANCE SETTING RETURN gt EXIT gt ADVANCE SETTING AUTO FLIP REDUCE SPEED IMAGE FREEZE CTRL DIR MODE NORMAL gt SOFT ADDRESS AZIMUTH SETTING MASK SETTING VIDEO SYNC COMM TESTING RETURN gt EXIT gt SOFT ADDRESS SETTING CURRENT SOFT ADDRESS NO 1 F SOFT ADDRESS EN RESET SOFT ADDRESS NO RETURN gt IR Intelligent Integration Camera Installation and User Manual You can open soft address function to enable it from the menu The address identified by dial up address of the u
45. f patrol to start preset point patrol e g call preset point No 51 to start the 1 preset point patrol between No 1 and No 16 28 IR Intelligent Integration Camera Installation and User Manual Camera menu Call preset point No 60 to open camera menu this function needs camera to support and then select menu item by zooming in TELE and zooming out WIDE modify selected value by focusing far FAR and focusing near NEAR modify or open submenu by opening lens aperture OPEN The above operations are the common camera operations the specific operations should be referred to the present using camera Camera Display 1 Close display Call preset point No 61 to close all characters presented on screen 2 Open display Set presets point No 61 to display often used items on screen Often used items include Display angles and compass function need OSD module support Zoom value display e Preset position indicate Horizontal auto scan 1 Start auto scan Call preset point No 65 call scan number Scan number 1 2 3 4 5 Speed level 1 level 2 level 3 level 4 level 5 level clockwise Scan number 6 7 8 9 10 Speed level 6 level 7 level 8 level 9 level 10 level Scan number 11 12 13 14 15 Speed level 1 level 2 level 3 level 4 level 5 level anticlockwise Scan number 16 17 18 19 20 Speed level 6 level 7 level 8 level 9 level 10 level E g Call preset point No 6
46. f transportation and storage the product should be avoided from incorrect operations such as heavy pressing strong vibration soaking etc which may cause damage to the unit This unit must adopt parts packing transportation regardless of delivery or return to factory maintenance The damage which caused by assemble packing transportation is not covered by the warranty Careful installation During the course of installation the product should be handled properly and should be avoided from incorrect operations such as squeeze the structure parts heavy press strong vibration etc which may cause mechanical problem and reflect the overall performance of the unit The dome cover of the unit which belongs to advanced optical products should be avoided from incorrect operations such as directly touch by hand which may scratch the cover and affect image quality Please follow all electrical standards for safety when it s being connected and adopt the particular power supply which is provided with the unit Control signal and video signal should be kept enough distance from high voltage equipments and cables when they are in transmission and necessary steps should be taken to prevent lightning damage or power surge Don t turn on power before finish installation Don t dismantle Don t dismantle the unit there are no parts inside the unit which can be repaired by the users themselves When mechanical problems arise do not be in a haste to do an
47. gt INTELLIGENT SETTING AUTO TRACK SETTING MOTION DET SETTING BORDER DET SETTING STATISTICS SETTING CONVERSE ANALYZE RESORT ANALYZE RETURN gt EXIT gt AUTO TRACK SETTING AUTO TRACK EN PRIORITY SIZE ZOOM TRACK RETURN TIME SPACE SETTING DELETE SPACE gt RETURN gt EXIT gt 6 SECOND The IR intelligent integrative camera can intelligently analyze the video images and automatically track the moving object in the monitoring area In tracking mode the unit will automatically tack the moving target when the monitoring area has moving target When the moving target moves out of the monitoring area or it can t trigger the tracking function the unit will stay for the preset dwell time and then return to the preset scene 1 Auto Track Enable Move the cursor to AUTO TRACK EN and select open and close options by moving the joystick to left and right 2 Priority Target Size Target size can be set to large medium and small and it means that how big the moving targets can trigger the function of auto track The setting method is move the cursor to PRIORITY SIZE and select options by moving the joystick to left and right 3 Zoom Track When the track function and zoom track function are open the unit will automatically adjust the zoom of the camera according to the size of the moving target so that the moving target can adapt to the scene of video screen Zoom track can be s
48. he cover is constructed with all alloy which ensures strong and durable Built in multilevel 3000V lightning protection surge protection and surges protection CO A 2 Function declaration This section describes the principle of main functions implementation not involve specific method of operation different platforms have different operation methods generally subject to operation manual of manufacturers there may be some special demand and operation methods in some cases please contact with the dealers to get necessary information Manual target tracking Users can control the camera to trace the moving object or change the monitoring area by moving the joystick on the keyboard up down left and right What s more the angle of view or the size of the image of the object can be changed by adjusting the focal length In the default Auto focus Auto lris state the lens can automatically quickly adjust to get clear image according to the change of the object x Auto flip In the process of operating the joystick to trace and monitor if the user move the lens to the bottom vertical then continues pressing the joystick the lens will automatically flip 180 horizontally then the user can still control it to move upwards till 90 which enables the user to directly observe the situation on the back side thus fore and aft 180 consecutive monitoring can be realized Set and call Preset position The preset position function
49. ic Users can adjust the camera exposure mode from the menu exposure mode can be set include automatic manual shutter priority IRIS priority brightness priority Note Different camera may have different exposure mode options The setting method is move the cursor to AE MODE and then select the mode you wanted by moving the joystick to left and right 5 Bright IRIS Shutter Users can adjust the image brightness from the menu The setting method is move the cursor to BRIGHT and then adjust brightness values by moving the joystick to left and right The setting methods of IRIS and shutter are similar to BRIGHT setting method The parameters of Brightness IRIS and shutter can adjust only when exposure mode is set to manual 6 Camera Antishock System default is close You can close and open the camera antishock function from the menu The setting method is move the cursor to ANTISHOCK and then select open or close option by moving the joystick to left and right 38 IR Intelligent Integration Camera Installation and User Manual Power Up Action Settina Once power on the unit enters self checking procedure DOME MENU when the self checking is finished the unit can run customize SYSTEM INFO commands DISPLAY SETUP CAMERA SETUP 1 DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt ENGLISH point 1 REBOOT gt Sa eae Move the cursor to POWER UP AC and then select the EXIT gt Power Up Act
50. ight OTHERS TEMPERATURE 23 C LANGUAGE ENGLISH CY TEMPERATURE UNIT CELSIUS RETURN gt EXIT gt 35 IR Intelligent Integrative Camera Installation and User Manual Display Setup DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt DISPLAY SETTING DOME TITLE PRESET POS DATE amp TIME AZIMUTH REGION DISP ALARM DISP TEMPERATURE DISP ZOOM DISP 9 DISPLAY POS SETTING RETURN gt ENGLISH 3 SECONDS 3 SECONDS 3 SECONDS CLOSE CLOSE DISPLAY POSITION SETTING CY DOME TITLE PRESET POSITION DATE amp TIME AZIMUTH REGION ZOOM DISP RETURN gt EXIT gt Display settings menu is used to set display mode of show Dome Title Preset Position Date amp Time Azimuth Region Alarm Display Temperature Display Zooms Display Setting options include Close Continuance 1 second 3 seconds 6 seconds 15 seconds items on the monitor The following is usable items Indicate the name of dome camera Indicate preset bits Show current date and time Show Horizontal and vertical angle Indicate region Show Alarm information Inner temperature of the unit Show Camera zooms Close display item Continuous display after activated Show 1 second after activated Show 3 seconds after activated Show 6 seconds after activated Show 15 seconds after activated The
51. integrated camera customizable specific protocol Video Freeze Realize video freeze during preset points calling need camera support Menu Chinese amp English NTSC PAL automatic identification output optional Timing Timing automatically start special function optional Lightning Protection Voltage of power interface is 4kV voltage of communication and video interface is 3KV 3 level surge protection Shell Aluminum case Acid rain proof High hardness Protection Grade Meet IP66 FCC CE and pass the Chinese MPS test Installation Kinds of installation type Select one according to application The above specifications are subject to change without prior notice 26 IR Intelligent Integration Camera Installation and User Manual V Functional Instructions 5 1 Common function quick instruction list The unit has 204 preset points preset point number 1 48 and 100 255 for effective preset points and 49 99 for common function quick command you can quickly use the common function by calling or setting these particular preset point numbers number Call preset point Set preset point Remarks 50 Start the 1 pattern Record the 1 group pattern Pattern scan function 51 Start 1 preset point patrol Set dwell time of the 1st patrol gt gt 1 16 preset point patrol 52 Start 2 preset point patrol Set dwell time of the 2 patrol gt gt 17 32 preset point patrol
52. into many small pieces through the grid lines in order to orientate conveniently The setting method is move the cursor to GRID LINE and select open or close option by moving the joystick to left and right 2 Mask Zone Number The setting method is move the cursor to MASK NO and select number by moving the joystick to left and right Note This function needs support by the camera The number of mask area is related to camera models 3 Mask Enable System default is close Move the cursor to MASK ENABLE and select open or close option by moving the joystick to left and right 4 Mask Zone Setting Move the cursor to SETTING and press lt IRIS OPEN gt to enter the position setting mode of mask zone and then operate the joystick to control the unit move the zone which need to be masked to the center of the screen and then press lt IRIS OPEN gt to enter the size setting mode of mask zone and then adjust the size of mask area by moving the joystick to up down left and right then press lt IRIS OPEN gt after the setting is complete 5 Clear Mask Zone Move the cursor to CLEAR and press lt IRIS OPEN gt to delete the corresponding mask area of numbers 49 IR Intelligent Integrative Camera Installation and User Manual Communication Test The unit can diagnose the stability of communication lines DOME MENU with TA8000 control software Start communications test through SYSTEM INFO DISPLAY SETUP CAM
53. ion Settings system default call preset action which will run after power up by moving the joystick left and PETERE right Optional power up actions total 18 kinds of action options op No action STANDBY SETTING DATA amp TIME SETTING Call Preset point No 1 to No 8 PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING 4 ADVANCE SETTING Start the first or the second horizontal sweep RETURN gt EXITS Start the first or the fifth auto scan Start the first or the second preset point patrol Start the first or the second pattern Start auto track 39 IR Intelligent Integrative Camera Installation and User Manual Standby Setting 7 STANDBY TIME STANDBY AC RETURN gt EXIT gt DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH DOME SETTING POWER UP AC CALL PRESET POINT 1 P STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt STANDBY SETTING 30 SECONDS NO ACTION Standby also called standby or idle action setting means that if users have no operation within the specified time the unit will run the specified function 1 Standby Time System default is 30 seconds Move the cursor to STANDBY TIME and select standby time by moving the jo
54. ion and User Manual Title setting Set the unit s title from the menu and display it on monitor so BONE MENU as to identify each monitor point easily The method is as follows SYSTEM INFO Input method may be Digit Uppercase Lowercase Specific DISPLAY SETUP BOME SETI symbols and Chinese etc BEHAVIOR SETUP n LANGUAGE SETUP gt ENGLISH 1 Move the cursor to TITLE SETTING and press lt IRIS REBOOT gt P SELIING OPENsto enter title setting mode and then move the cursor EXIT gt to INPUT TYPE by moving the joystick to up and down and select suitable input methods by moving the joystick to left DOME SETTING POWER UP AC CALL PRESET POINT 1 STANDBY SETTING _ DATA amp TIME SETTING Lowercase Specific symbols and Chinese PASSWORD SETTING oon 2 Move the cursor to the next line under option of INPUT CP TITLE SETTING i 7 ADVANCE SETTING TYPE and press lt IRIS OPEN gt to enter character input RETURN gt and right Optional input method is Digit Uppercase mode at this time the selected character is twinkling select character by moving the joystick to up down left and right TITLE SETTING press lt IRIS OPEN gt to put the twinkling character into the INP INPUT TYPE LOWERCASE position of in INPUT MSG column 3 After the input is completed move the cursor to ENTER and press lt IRIS OPEN gt to confirm input and return to the previous
55. itch off Options 15 seconds 30 seconds 1 minute 5 minutes and 15 minutes 8 Start time and end time of schedule Start time and end time of schedule means the time to open close alarm only when START SCHEDULE is set to TIMING this setting is valid Move the cursor to START END SCHEDULE time input please refer to the section of Date and Time Setting 43 IR Setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP CF DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt HELP gt EXIT gt ENGLISH DOME SETTING POWER UP AC STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SETTING CALL PRESET POINT 1 IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt IR CONTROL SETTING gt IR CONTROL MODE IR LED BRIGHT ON TIME OFF TIME FAR amp NEAR MODE THRESHOLD SCAN INTERVAL RETURN gt EXIT gt 15 SECONDS IR Intelligent Integrative Camera Installation and User Manual You can open and close IR lamp or set working mode of IR lamp through the menu of IR setting 1 IR Control Mode System default is automatic Auto IR LED can automatically open and close according to the brightness Timing IR LED can open and close according to the timing Open Compulsorily open the IR lamp Close Compulsorily close the IR lamp 2 IR LED Bright System default is high power You can set IR LED bright
56. ly can be used when express mode is open e g call set 53 call set 3 means that you need to continuously call set preset No 53 and then call preset No 3 within 15 seconds when the unit is in readiness the followings are similar Time corresponding preset point table Preset point of Time 1 2 3 4 5 6 7 Time 1sec 3 sec 6 sec 15 sec 30 sec 1 min 5 min Preset point of Time 8 9 10 11 12 13 14 Time 15 min 30 min 1 hours 8 hours 12 hours 24 hours reserve Action corresponding preset point table Preset point of Action Action 1 No action 2 9 Preset point number 1 8 10 11 Preset point patrol 1 and 2 12 13 Horizontal sweep 1 and 2 groups 14 15 Auto scan 1 and 5 groups 16 17 Pattern 1 and 2 groups 18 Auto tracking Pattern scan 1 Record pattern Set preset point No 50 to enter into record mode and then operate the unit left right up down zoom and calling preset point When the record is complete press lt IRIS OPEN to exit 2 Start pattern To start scanning the 1 pattern call preset point No 50 or No 97 Preset point patrol 1 Set preset point Set the corresponding preset point 2 Set dwell time Set preset point number of patrol preset point number of time e g set time of the 1st preset point patrol to 15 seconds the operator is set preset point No 51 No 4 3 Start patrol Call the corresponding preset point number o
57. meric inputs only accept digital input The setting method is as follows Date and Time Setting Move the cursor to the corresponding item by moving the joystick to left right up and down and then press lt IRIS OPEN gt to enter corresponding interface of numeric inputs In PUT MSG column select input position by moving the joystick to left and right and the selected position presents a twinkling state at this moment Move the cursor to digital area by moving down the joystick and press lt IRIS OPEN to select the digit and the selected digit will present a twinkling state select corresponding digit by moving the joystick to left right up and down and then press lt IRIS OPEN gt to confirm at the same time the input position moves to the next position in IPUT MSG column If you input an error digit you can move the twinkling character to position and press lt IRIS OPEN gt to delete it at the same time the input position moves to the previous position in IPUT MSG column After completely input you can press lt IRIS CLOSE gt to exit digital area and the digit in digital area will stop twinkling Move the cursor to ENTER by moving down the joystick and press lt IRIS OPEN gt to confirm input and return to the interface of Data amp Time setting If the cursor moves to CANCEL press lt IRIS OPEN gt to cancel modification and return to interface of Data amp Time setting 2 Confirm Setting Move the
58. nit will be shielded at this time 1 Soft Address Enable The setting method is move the cursor to SOFT ADRESS ENABLE and select open or close option by moving joystick to left and right 2 Reset Soft Address Number Move the cursor to RESET SOFT ADDRESS NO and press lt IRIS OPEN gt to enter soft address number setting mode and then input the required number of soft address About how to input soft address number please refer to Date and Time Setting 47 IR Intelligent Integrative Camera Installation and User Manual Azimuth Setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt ENGLISH REBOOT gt FACTORY SETTING gt HELP gt EXIT gt DOME SETTING POWER UP AC CALL PRESET POINT 1 STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt Q ADVANCE SETTING AUTO FLIP REDUCE SPEED IMAGE FREEZE CTRL DIR MODE NORMAL SOFT ADDRESS CF AZIMUTH SETTING MASK SETTING VIDEO SYNC COMM TESTING RETURN gt EXIT gt l AZIMUTH SETTING ARE YOU SURE TO SET CURRENT POSITION TO NORTH CP CONFIRM gt CANCEL gt DEFAULT gt ADJUST You can set horizontal azimuth from the menu The north direction is 0 angle direction in horizontal and corresponds with N orientation of the compass 1 A
59. nt high speed dome camera installation C serial wall mounted structure PA v OA Ll bracket dome base IR dome body dome cover C serial pendent mounted structure bracket dome base IR dome body dome cover Installation steps of wall mounted unit 1 4 Take dome base out from the packing box Pull the wire and cable out through the bracket fix the IR dome body firmly to the bracket with M6 socket head screws which are along with the unit As shown on the left Fix the bracket firmly onto the pre installed setscrews on the wall with four M8 nuts Take out IR dome body from the packing box Setup communication protocol baud rate and address through SW1 and SW2 at the bottom of the dome body When install the dome body dome body s socket need to correspond with the dome base s socket Hold the camera with both hands aim the dome body s clip at the dome base s bayonet Note the red marks correspond put the clip into bayonet slowly and then press the top of clip with a little force you can confirm the installation is set at positions after heard two crisp voice of a combined bump Note Confirm the dome body was completely stuck or else the dome body may cover off or the dome cover may be fretted Pull down the dome body lightly to check whether the dome body is completely stuck Install d
60. o confirm the selected items Press lt IRIS CLOSE gt to return to the previous menu or exit the menu Menu item meaning CF Currently selected menu item Menu item The menu item has submenu Menu item gt This menu item can operate after pressing IRIS OPEN button Menu item This menu value can be modified by move the joystick to left and right Back gt Return to the previous menu Exit gt Exit the menu Access the main menu call preset point No 95 You can call preset point No 95 to open the main menu on the monitor 33 IR Intelligent Integrative Camera Installation and User Manual DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt ENGLISH REBOOT gt FACTORY SETTING gt HELP gt EXIT gt 34 INTELLIGENT HIGH SPEED DOME VERSION V3 01 PROTOCOL AUTO IDENTIFICATION BAUDRATE 2400 N 8 1 ADDRESS 3 HP201 10203001 2011 04 01 TITLE INTELLIGENT HIGH SPEED DEMO OTHERS RETURN gt EXIT gt DISPLAY SETTING DOME TITLE PRESET POS DATE amp TIME AZIMUTH 3 SECONDS REGION DISP 3 SECONDS ALARM DISP 3 SECONDS TEMPERATURE DISP CLOSE ZOOM DISP CLOSE DISPLAY POS SETTING RETURN gt CMAERA SETTING FOCUS MODE D ZOOM BLC ICR ZOOM SPEED WIDE DYNAMIC V FLIP MIRROR ADVANCE RETURN gt EXIT gt DOME SETTING POWER UP AG CALL PRESET POINT 1 STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SE
61. ome cover onto dome base and fix them Installation steps of pendent mounted unit 1 Take dome base out from the packing box Pull the wire and cable out through the bracket and fix the IR dome base firmly to the bracket with M6 screws As shown on the left Aim at four open holes on the ceiling and fix the bracket firmly to the pre installed setscrews on the ceiling with four M6 nuts Refer to the installation steps of wall mounted unit 10 IR Intelligent Integration Camera Installation and User Manual E series of IR intelligent high speed dome camera installation E serial wall mounted structure Installation steps of wall mounted unit 1 Take IR dome body from the packing box Set up e i re communication protocol baud rate and address Pull the wire and cable out through the bracket and then aim at four open holes on the bracket and fix the IR dome camera x firmly to bracket with M6 socket head screws along with the IR dome camera unit As shown on the left _ 2 Aim at four open holes on the wall and fix the bracket firmly to the pre installed setscrews with four M8 nuts 3 Please refer to the instruction to connect the power supply video and controlling cables Installation steps of pendent mounted unit E serial pendent mounted structure 1 Take out IR dome body from the packing box Setup gt communication protocol b
62. on of Functions IR intelligent integrative Camera is equipped with high performance DSP camera with zooming lens higher efficiency IR lamps built in PTZ and digital decoder which represents the future trend of high technology monitoring products The unit is adopts full digital control flexible programming and exquisitely simple transmission system design The unit is capable of rapid positioning and consecutively tracing and scanning which realizes the real sense of all directional and no blind spots monitoring The unit support PELCO D PELCO P TAO1 and other communication protocol makes operation more flexible and simple The series of IR intelligent integration camera can be applied in every walk of life to monitor moving objects in larger areas such as monitoring banks airports transportation state government agencies power prisons hotels commercial buildings factories schools museums etc 3 1 Performance Characteristic 1 Functions Introduce Adopted full functional high performance DSP design performance stable and reliable 3D positioning function realize screen coordinate positioning and partial enlarges through software Minimum hand controlling speed of stable operation is 0 01 S Maximum patrolling speed of precise positioning is 350 S Reserved network module interfaces can be loaded to network intelligent camera Support and automatic identification PELCO D PELCO P TAO1 and other communic
63. or 6 Color and black and white conversion function only for cameras with color and black and white conversion function The camera with night vision function will automatically switch CCD illumination according to the ambient light in automatic color and black and white conversion mode For example During the day the light is enough the camera can use general illumination to get brightly colored picture while in night the camera can automatically change low illumination to get clear object with black and white picture 15 IR Intelligent Integrative Camera Installation and User Manual Users can set color and black and white conversion mode to manual by the keyboard in this case the camera can not automatically make corresponding conversion according to ambient light Users can manually select color or black and white pictures shown Set toggle switches Before installing the IR Intelligent Integrative Camera please configure protocol baud rate and address code The factory default automatic identification protocol amp baud rate is address code 1 ON ON N a JODO DA DU DU DA DA DA DA DA 1 2 3 6 7 8 1 2 3 7 8 5 6 SW1 Protocol amp baud rate toggle switch SW2 address code toggle switch Part of the Data chosen switches protocol amp baud rate ON ON ON 7 DADE DU DU DU DU DA DA SMM MN N Bi it 23 4 amp 56 Tf 38 123 4 5 7 8 6 7 8 5 6 7 123 45 Auto identification protocol amp baud rate
64. oved to center of the field Pattern pattern scan The IR Intelligent integrative Camera can continuously record running track for 600 seconds or 500 instructions after start pattern the unit can automatically cyclic scanning and monitoring according to pre recorded trajectory Standby mode Users can preset idle time and action mode of IR Intelligent Integrative Camera call presets auto sweep function automatic patrolling pattern memory recalling function once power off if users have no action within the setting time the unit will automatically start up preset action Menu function The menu can satisfy different customers requirement by support Chinese and English full screen operation The menu can be made to other langue according to customer s demand Timing action function Users can set different action in different time and then can realize seven days a week eight periods a day automatic setting function Azimuth setting function Users can set up north direction to realize the precise display of rotation direction IR intelligent integrative camera also supports region indication When the unit is turned to a preset area the screen can show the title of the preset area 14 IR Intelligent Integration Camera Installation and User Manual Mask function For the privacy and safety area some black lumps can be set to mask zones The size and position of the black lumps can be adjustable Altogether 24 privacy
65. s switched on Abnormal self check image shown with motor noise Camera inclined Possible causes solutions Power supply adaptor damaged or sod Replace Power supply not sufficient Wrong contact of power cables Correct Engineering line fault Exclude Mechanical failure Repair Reinstall Power supply not sufficient Replace better to place the adaptor nearby the unit Normal self check and image but out of control Wrong contact of control signal Wrong contact of video lines Correct Normal self check Bad contact of video cables Exclude but no image Camera is damaged Replace Correct Address configuration wrong Choose new address and power on Protocol or Baud rate configuration Adjust Protocol baud rate to match controller and power on Unstable image Power cables too long wrong Bad contact of video cable Exclude Power supply not sufficient or PPY Replace IR intelligent integrative camera out of control Abnormal self check Power On again Bad contact of control lines Remove The host operations have a problem Power on the host again the load is too much the distance is too far Increase yards distributor control Focus is in automatic mode Focus out of Set focus mode to manual 59 IR Intelligent Integrative Camera Installation and User Manual Lightning and Surge Protection This product adopts Cerami
66. t can sustain four times the weight of the product 2 Cable preparation 1 Select cables according to transmission distance the minimum specification requirements of vision coaxial cable is as below 75Q impedance Copper wire 95 braided copper mesh shielding Domestic Model International Model Maximum distance meters feet RGS59 U RG59 U 229m 750ft 5C 2V RG6 U 305m 1000ft 7C0 2V RG11 U 457m 1500ft The same type of video cables may be different depending on manufacturer The data shown in above table is the transmission distance of general vision cable IR Intelligent Integration Camera Installation and User Manual 2 The following data is recommended maximum distance for application of 24VAC or 24VDC the distance is calculated from 10 voltage drop For AC or DC electric driving equipment the maximum allowable voltage drop is 10 Cable diameter 0 5mm 20AWG 1mm 18AWG 1 5mm 16AWG 2 5mm 14AWG Power 23W 38m 123ft 60m 196ft 95m 311ft 151m 495ft Power 72W 12m 39ft 19m 62ft 30m 98ft 48m 156ft 3 Toggle switch setting Set the toggle switch according to the control protocol baud rate and address Refer to the third chapter lt Description of Functional gt 2 2 Installation A series of IR intelligent high speed dome camera dimension figure Wall Mounted ir Pendent Mounted
67. t verge and the right verge are set firstly The priority of region indication is No 1 as highest priority and No 8 as lowest priority When deferent regions are overlap only higher priority region can be shown The setting method is as follows 1 Set Region Number Move the cursor to the REGION NO and select the region Number by moving the joystick to left and right 2 Set Region Title Move the cursor to REGION TITLE and press lt IRIS OPENs gt to enter the submenu of the region title setting and then set the region title referring to the section of Title Setting 3 Set Left Verge Move the cursor to LEFT VERGE and press lt IRIS OPEN gt to enter the verge setting mode and then move the cursor to expected position by operating the joystick and then press lt IRIS OPEN gt to storage the current position as the left verge 4 Set Right Verge Move the cursor to RIGHT VERGE and press lt IRIS OPEN gt to enter the verge setting mode and then move the cursor to expected position by operating the joystick and then press lt IRIS OPEN gt to storage the current position as the right verge 5 Delete Region Indication Move the cursor to DELETE and press lt IRIS OPEN gt to delete the corresponding region of region number 57 Reboot system DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt ENGLISH F REBOOT gt FACTORY SETTING gt HELP gt
68. telligent Integration Camera Installation and User Manual Welcome Thank you for purchasing IR intelligent integration camera This manual is used as a reference for operating and programming the unit You can find relevant information of functions and commands as well as detailed menu tree and fast operating instructions in this manual The section of installation provides the needed information for setting and installing the unit Before installing and using the unit please well understand the information in this manual IR Intelligent Integrative Camera Installation and User Manual Important Safeguards This manual is the basic instructions about IR intelligent integrative camera This manual consists of important information of security and warning function specification performance characteristics and parameters installation steps general faults and the solution to get out of them maintenance and others need to know when using the IR intelligent integrative camera If you first use the IR intelligent integrative camera or ever used the similar products you had better read this manual before using this unit If possible please start reading from the first page in sequence If you just hope to see the needed parts you also can select them from catalogue Please refer page 29 to get the function list of the unit This unit uses special preset points to realize some function operation Careful Transportation During the course o
69. tly call preset point No 49 to enter into function selection mode and then call corresponding preset point number N in the following table to start the corresponding function It must be coherent when call these two preset point If action between these two ca point No 49 again to enter the function selection mode ls is not call preset point this operation is invalid you need to call preset Preset points number N Functional Description Remark 1 Switch sensitivity mode of IR to high The higher the IR sensitivity the easier to 2 Switch sensitivity mode of IR to medium switch to IR 3 Switch sensitivity mode of IR to low black and white mode 7 Manually compulsorily open the IR lamp ion of IR lamp 8 Manually compulsorily close the IR lamp Operation 9 aps switch 9 Auto control the IR lamp s switch 50 Auto control the IR lamp s brightness Control Brightness of IR 57 Manually set the IR lamp to low brightness lamp 59 Manually set the IR lamp to high brightness the function is system default 32 IR Intelligent Integration Camera Installation and User Manual 5 2 Menu operation guide The following menu for units with OSD 5 Call preset point No 95 to open the menu PRESET Move the joystick up and down to select menu items Move the joystick left and right to modify the value of menu items Press lt IRIS OPEN gt to enter submenu or t
70. works in this way The IR Intelligent Integrative Camera stores the data of PTZ horizontal angle tilt angle and lens focal length in the current state The user can quickly and conveniently storage and call the preset position by the keyboard and other control equipment and then move the PTZ and camera module to the corresponding position 13 IR Intelligent Integrative Camera Installation and User Manual Focal length speed automatic matching techniques When the focus is long and in the mode of manual adjustment due to the high sensitivity of the IR Intelligent Integrative Camera even the slightest movement of the joystick would make the image move quickly and cause image losses Based on human design the IR Intelligent Integrative Camera can automatically adjust the horizontal and vertical moving speed according to the current focal length which makes the manual target tracing operation much easier Auto sweep function The auto sweep function is a built in function of the IR Intelligent Integrative Camera which can pre set Left Right limiting positions The user can run the left right scan directly through an external command and then the dome camera will automatically run horizontally between the left limiting position and the right limiting position at the preset speed 3D positioning function In the effective zoom range of the unit users can directly enlarge and narrow all area of screen view and put any point in the view m
71. y repairing please refer to the User s Manual to find the trouble If causes can not be located please refer servicing to qualified professionals All servicing must be done by authorized personnel IR Intelligent Integration Camera Installation and User Manual Set in place far from electric and magnetic fields If the unit is set near EMI source such as television wireless transmitter electromagnetic device motors transformers speakers etc which may create electromagnetic field the electromagnetic field will influence images Please keep sufficient distance Don t aim the camera at light objects No matter the unit is running or not the camera should never be aimed at the sun or object with extremely bright light and never be aimed at or monitor immobile light object for a long time Otherwise the camera s CCD might be permanently damaged Careful maintenance The camera should be carefully used and avoided form impact or vibration otherwise it will be damaged Don t use strong or corrosive detergent to clean dome camera s body You should clean it with dry cloth When the dirt is not easy cleared you can wipe it by neutral detergent If the camera lens is dirty please wipe it by the special paper Please use this product in the required working environment Working Environment IR intelligent dome camera Environmental Temperature 35 40 C Environmental Humidity lt 95 Atmospheric Pressure 86 106KPa
72. ystick to left and right The options of standby time are 15 seconds 30 seconds 1 minute 5 minutes 15 minutes 30 minutes 1 hour 8 hours 12 hours and 24 hours 2 Standby Action System default is no action Move the cursor to STANDBY ACTION and select standby action by moving the joystick to left and right The options of standby actions are total 18 kinds of action options No action Call Preset point No 1 to No 8 Start the first or the second preset point patrol Start the first or the second horizontal sweep Start the first or the fifth auto scan Start the first or the second pattern Start auto track 40 IR Intelligent Integration Camera Installation and User Manual Date and Time Setting The unit has date and time display function user can modify DOME MENU SYSTEM INFO DISPLAY SETUP 1 CAMERA SETUP CF DOME SETUP 1 BEHAVIOR SETUP LANGUAGE SETUP gt REBOOT gt FACTORY SETTING gt ENGLISH HELP gt 3 EXIT gt DOME SETTING POWER UP AC CALL PRESET POINT 1 STANDBY SETTING CF DATA amp TIME SETTING 3 PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt DATA amp TIME SETTING DATE 2011 04 01 TIME 12 00 CONFIRM gt CANCEL gt DATA INPUT INPUT MS INPUT TYP DIGIT 4 0123456789 ENTER gt CANCEL gt Data input inteface system date and time from the menu Interface of nu
73. zimuth Setting To set the current position to the north direction move the cursor to CONFIRM and press lt IRIS OPEN gt to confirm that the current position is north direction If you need to readjust move the cursor to ADJUST and press lt IRIS OPENs and then reorientate the north direction by moving the joystick to left and right and press lt IRIS OPEN gt to confirm modification after the setting is complete 48 Mask Setting DOME MENU SYSTEM INFO DISPLAY SETUP CAMERA SETUP DOME SETUP BEHAVIOR SETUP LANGUAGE SETUP gt ENGLISH REBOOT gt FACTORY SETTING gt HELP gt EXIT gt DOME SETTING POWER UP AG CALL PRESET POINT 1 STANDBY SETTING DATA amp TIME SETTING PASSWORD SETTING ALARM SETTING IR SETTING TITLE SETTING ADVANCE SETTING RETURN gt EXIT gt ADVANCE SETTING AUTO FLIP REDUCE SPEED IMAGE FREEZE CTRL DIR MODE NORMAL SOFT ADDRESS AZIMUTH SETTING MASK SETTING VIDEO SYNC COMM TESTING RETURN gt EXIT gt MASK SETTING CP GRID LINE MASK NO MASK ENABLE SETTING CLEAR gt RETURN gt EXIT gt IR Intelligent Integration Camera Installation and User Manual Mask function allows that privacy zones in the monitoring image can be shielded by black box Altogether 8 Privacy Mask zones can be set in the unit The setting method is as follows 1 Grid Line Display System default is close The whole screen image can be divided
74. zones can be set in the unit This function needs support of the camera Set address This IR Intelligent Integrative Camera support 255 addresses the unit only responds to the command of its own address or broadcast address The address can be set by toggle switch or soft address function of the menu Camera control 1 Zoom control Users can adjust the zoom by controlling the keyboard to get panoramic view or close view 2 Focus control System default is automatic focus While the lens moves the camera module can automatically focus on the center of the object view to get clear image In special conditions users can manually adjust the focus to achieve desired image effect 3 Auto iris control The iris can automatically influence the change of ambient light and make quickly adjustment to output image of stable brightness 4 Automatic backlight compensation When the backlight compensation function is turned on In extremely bright background the camera module can compensate the brightness of the relatively dark objects at the same time adjust the light of the bright background avoiding that the whole image is too bright to watch due to the too high brightness of the background while the object is too dark to be distinguished so that clear image can be got The system closed this function as the default 5 Auto manual white balance According to the ambient light automatically or manually adjust the light to reappear the real col

Download Pdf Manuals

Related Search

Related Contents

ProLite E383-1 /S-1  AR283 - FR - version 1.3    Hitachi VTFX695A VCR User Manual  Seagate Barracuda 4TB HDD SATA  

Copyright © All rights reserved. Failed to retrieve file