eBOX670-883-FL User`s Manual VA1
Contents
1. You can use this screen to select options for the Super IO Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen For items marked with gt please press lt Enter gt for more options gt Serial Port 1 Configuration Serial Port 1 4Configuration Use these items to set parameters of Serial Port 1 4 BIOS Setup Utility 43 eBOX671 885 FL Series User s Manual e Serial Port 1 Configuration Serial Port Enabled Serial Port Use this item to enable or disable serial port 1 The optimal setting for base VO address is 3F8h and for interrupt request line is IRQ4 Select Mode Use this item to configure serial port 1 Here are the options for your selection RS232 RS422 RS485 44 BIOS Setup Utility eBOX671 885 FL Series User s Manual e Serial Port 2 Configuration serial Port Enabled Serial Port Use this item to enable or disable serial port 2 The optimal setting for base VO address is 2F8h and for interrupt request line is IRQ3 Select Mode Use this item to configure serial port 2 Here are the options for your selection RS232 RS422 RS485 BIOS Setup Utility 45 eBOX671 885 FL Series User s Manual e Serial Port 3 Configuration Serial Port Enabled 4 a Exit raull vi ye Fa Save 8 E ESC Exit Serial Port Use this item to enable or disable serial port 3 The optimal setting for base2. eBOX671 885 FL Series Embedded System Disclaimers This manual has been carefully checked and believed to contain accurate information Axiomtek Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document Axiomtek does not make any commitment to update the information in this manual Axiomtek reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Axiomtek Co Ltd Copyright 2015 Axiomtek Co Ltd All Rights Reserved March 2015 Version A1 Printed in Taiwan Safety Precautions Before getting started please read the follovving important safety precautions L The eBOX671 885 FL does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electronic components a
3. 2 Cl DATA M GAD 20 Di Spc Di SPD Dit DATAL E CH LA ois z llo 2 2 oln ayo g a Ol DAT A e e ta Pt in E T DWI_HTPLG Dl DATAD Cl DAT A hi hi DI OLR J Ja Di OLE Oo ha Analog red Analog green m E Analog blue Analog horizontal sync Analog ground Jumper Setting Connector 27 eBOX671 885 FL Series User s Manual 3 35 COM1 COM4 Serial Port Connector The system has four serial ports COM1 COM2 are RS 232 422 485 ports Please refer to Chapter 4 for the detail of BIOS setting COM3 COM4 are RS 232 ports COM COM JO o Lil vatasetreay nouse nouse ATS Request To Send Le 7 crs cearto sen x COM3 COM4 RTS Request To Send CTS Clear To Send RI Ring Indicator le e 15 DSR Data set Ready ra EN 28 Jumper Setting Connector eBOX671 885 FL Series User s Manual 3 3 6 USB 3 0 Connector The Universal Serial Bus connectors are compliant with USB 3 0 5Gb s and ideally for installing USB peripherals such as scanner camera and USB devices etc Signal USB Port 0 i Signal USB Port 1 USB_VCC 5V level USB VCC 5V level standby standby power power USB Data2 USB Data3 USB Data2 USB Data3 18 1 16 15 14 GND GND 10 11 12 13 SSRX2 SSRX3 an 1 2 3 4 SSRX2 SSRX3 GND GND SSTX2 SSTX3 SSTX2 SSTX3 3 3 Ethernet Connector LAN1 L
4. SE USB 20 Glog y ice ce asustan ibi idilio 29 3 3 7 Ethernet Connector LAN1 LANO nanunnnnnnnnnanesen nonen ene re non sene ee nn esse eren n esse eee ensees 29 A A a 30 d E E Audio o AA Ae 30 3 3 10 Digital GOC LOT geni nv r ne ni ndie sinan k 30 3 3 11 Isolated Digital UO Connector Option nana nananaccnn nane nenen even non nenes eee eren nse eee enen 31 3 3 12 ATX EREECHEN beet 32 20 19 Reset BULTON gn ge EeEEEeR e gek geNeCEeeedegegee 32 3 3 14 Remote Power Switch Comme ctor nana an nnn nana nena nenen nane ee non eee e nge ee sen n esse rene nenes 32 E rai 33 E A aa ga an 33 3 3 17 SATA Connector SATA 18 2 anunaaa nana cen nanen na cenon cenonte ven cereeeeeeevee ee ver eee seserer eres 34 3 3 18 SATA Power Connector sana NARA 34 E e 34 3 3 20 Full Size PCI Express Mini Card Slot oocccccccccccccooononcccccnnnnnnnncnnnnnnnnnnnnnanas 35 CHAPTER 4 BIOS SETUP UTILITY asnicar 37 1 3 o AA A 37 4 2 Advanced MENU nan nn riian 39 4 4 Giele VU EE 53 APPENDIX A WATCHDOG TIMER oocccccccccccccccccccccccococonoooooooccocccccc00o 58 PRODUIT Wailchdog TIMET nese Ea 58 SM PI rs 59 viii eBOX671 885 FL Series User s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the eBOX671 885 FL The Chapter 1 includes the following sections General Description System Specifications Dimensions I O Outlets Packing List Model List 1 1 General Des
5. lt Enter gt for more options p ACF I Settings ONG E save QEgit NM ESC Exit BIOS Setup Utility 39 eBOX671 885 FL Series User s Manual e ACPI Settings You can use this screen to select options for the ACPI configuration and change the value of the selected option A description of the selected item appears on the right side of the screen Enable ACPI Auto Configuration Disabled Enable ACPI Auto Configuration Values Enabled Disabled Enables or disables BIOS AGPI Auto Configurations When enabled the following two parameters are hidden Enable Hibernation Values Enabled Disabled Enables or disables the system s ability to hibernate S4 Sleep State The setting of this option may have no effect with some operating systems ACPI Sleep State Allow you to select the Advanced Configuration and Power Interface AGPI sleep state Here are the options for your selection Suspend Dissabled and S3 Suspend to RAM The S3 Suspend to RAM option selects the highest ACPI sleep state the system will enter when SUSPEND button is pressed 40 BIOS Setup Utility eBOX671 885 FL Series User s Manual e CPU Configuration This screen shows the CPU information gt CPU Information Enter Select Change Opt General Help Previous Values Optimized Defaults Save amp Exit Hyper threading To enable hyperthreading you must first enable it in your system s BIOS settings the default
6. m2 x RJ 45 connectors for 10 100 1000 Base T Ethernet ports Intel i211 AT PoE Power over Ethernet Controller Intel i211AT x 4 Compliant 4ports full load IEEE802 3af Class 2 7Watt 2ports full load IEEE802 3af Class 3 15 4Watt ports full load IEEE802 3at Class 4 30VVatt Power Output Total maximum 30 watt for 4 ports USB Ports m6 x USB 3 0 amp 2 x USB 2 0 ports Serial Ports m2 x RS 232 422 485 and 2 x RS 232 by 9 pin D Sub male connectors jumper less DIO 8 CH programmable digital I O by 9 pin D Sub female connectors 8 CH Isolated digital I O m amp 4out by phoenix type connectors Option Mini PCle Interface m2 x PCI Express Mini Card Slots w mSATA supported Storage m2 x 2 5 SATA HDD SSD drive bay mi x CFast m2 x mSATA Indicator m 1 x Orange LED for HDD active m1 x Blue LED for system power Introduction 3 eBOX671 885 FL Series User s Manual Switch m1 x Power switch m1 x Reset switch m1 x AT ATX switch m1 x Remote PWR switch connector SIM Slot x 1 1 2 3 System Specification Watchdog Timer E 1 255 seconds or minutes up to 255 levels Power Supply m 24V DC input Operation Temperature m 20C 50C 4 F 122 F with W T SSD 8 Memory CPU TDP 35W Storage Temperature m 40 C 80C 40 F 176 F Humidity E 10 90 non condensation Vibration Endurance u 3Grm w GFast 5 500Hz X Y Z directions Weight m 4 31 kg 9 5 Ib without
7. 11 2 1 Installing the CPU ProCeSSOl ccsssscsesseeceseesenseseeneeeneeseeneesens 11 2 2 Installing the SO DIMM nu naanan nanen case enes n e nse eren s enen e se rene res se ren sere ses eemss 15 2 3 Installing the 2 5 SATA Device nana nnnanne nanen case nn ene se skene sene REESEN emen 17 2 4 Installing the Express Mini Card nan una nanan nanen ns see nse rene skenes eren s e REENEN Een 19 2 5 Installing the CFast Card una unnnoann nonen soi se sos eren sene nese ene eres s seen se ee nse eesss 20 CHAPTER 3 JUMPER SETTING 8 CONNECTOOR cccccccssssssscrcecccssssees 22 3 1 Jumper amp Connector Location nun unnnnannn nanen seen esse rene skenes eren eren e eee nese 22 3 2 Jumper Setting Gummar nun nana nena anes seen nenes arena ee see kene esse nese s rene e ennnen 24 3 2 1 Mini Card Selection JP2 nannnnnnnnnnnnn nanen ere no oe see eren n ese e eren o esse eee nese eee eee nenes nenne 24 3 2 2 Restore BIOS Optimal Defaults UPS aanannaanannnn none neneve non ss er eren nese eee enes ese eemneess 24 3 3 OO pi ip 25 3 3 1 DC in Phoenix Power Connector da nnn ann nnn nana nena nenen nan err son teren neser e nge ee eee nenes 26 3 3 2 HDMI ConneCtON una nana nana nen nanen ren nane rena esse ee none eren nese sene esse ee nenes sene eee se enes eee e nenes 26 30 DISDIGV ON COPING DOJ e ar t 27 co Rs EEN 27 3 3 5 COM1 COM4 Serial Port CONNeCtOTF ccccccncnncccccnncnnconcnnnnnnconennnanncrrnnnnnnnnennnnas 28
8. I Introduction eBOX671 885 FL Series User s Manual 15 Packing List The package bundled with your eBOX671 885 FL should contain the following items eBOX671 885 FL System Unit x 1 eBOX671 885 FL Quick Installation Guide x 1 DVD x 1 For Driver and Manual Screws Pack x1 Pre installed Foot pad x4 Processor Thermal Pad x1 3 Pin Phoenix Power Connector x1 Remote Power Switch Cable x1 Optional Wall mount Kit Optional Antenna 1 6 Model List Fanless Embedded System with Intel Core 7 15 13 Celeron Processor Q87 PCH DVI I HDMI DisplayPort Dual HDD PoE 4 GbE LAN 2 USB 8 Audio COM 4 and 8 CH TTL digital VO 24VDC eBOX671 885 FL DC Fanless Embedded System with Intel Core 7 15 13 Celeron Processor Q87 PCH DVI I HDMI DisplayPort Dual HDD PoE 4 GbE LAN 2 USB 8 Audio COM 4 and 8 CH isolated digital I O 24VDC eBOX671 885 FL DC If you cannot find this package or any items are missing please contact Axiomtek distributors immediately Introduction 9 eBOX671 885 FL Series Users Manual This page is intentionally left blank 10 Introduction eBOX671 885 FL Series User s Manual CHAPTER 2 HARDWARE INSTALLATION The eBOX671 885 FL is convenient for your various hardware configurations such as Processor DRAM HDD Hard Disk Drive SSD Solid State Drive CFast card or PCI Express Mini Card modules The chapter 2 will show you how to install the hardware 2 1 Installing the CPU Process
9. SIS 5V level 3 3 19 SIM Card Slots eBOX671 885 FL includes one SIM slots SCN4 on the bottom side of the system for inserting SIM Card It is mainly used in 3G LTE wireless network application on SCNS 34 Jumper Setting amp Connector eBOX671 885 FL Series User s Manual 3 3 20 Full Size PCI Express Mini Card Slot SCN2 8 SCN3 There are two PCI Express Mini Card connectors on the bottom side applying to either PCI Express or USB 2 0 or SATA mSATA It complies with PCI Express Mini Card Spec V1 2 lt can also support mSATA cards Pin signal Pin Signal E GND 5 nouse Je 1 5 CLKREQ EN No use No use 11 merci 12 Nouse fis ono 16 nouse ano 22 PERSIA Ser eae 25 perxesy 26 GND er Lomp es etsy 29 KE SMB CLK END a PE Txn3 Las smB DATA ss pe rxe aa enn Las enD se use ps ar enD as use pss o 39 3 3VSB 40 GND Las Je aa No use E Nouse 46 nouse Nouse 48 Las PA se 51 Nouse Las lang Jumper Setting Connector 35 eBOX671 885 FL Series Users Manual This page is intentionally left blank 36 Jumper Setting Connector eBOX671 885 FL Series User s Manual CHAPTER 4 BIOS SETUP UTILITY This chapter provides users with detailed description how to set up basic system configuration through the BIOS setup utility 1 3 Starting To enter the setup screens follow the steps below 1 T
10. User s Manual DVMT Pre Allocated Dynamic video memory technology DVMT allows dynamic allocation of system memory for use as video memory to ensure the most efficient use of available resources for maximum 2D 3D graphics performance DVMT Total Gfx Mem Select DVMT 5 0 total graphics memory size used by the internal graphics device e Memory Configuration Use this item for further setting of memory configuration this screen displays memory information and allows user to set memory configuration 52 BIOS Setup Utility eBOX671 885 FL Series User s Manual 4 4 Boot Menu The Boot menu allows users to change boot options of the system etup Prompt Timeout Setup Prompt Timeout Number of seconds to wait for setup activation key 65535 0xFFFF means indefinite waiting Bootup NumLock State Select the keyboard NumLock state Quiet Boot Enables Disables Quiet Boot option Launch PXE OpROM Controls the execution of UEFI and Legacy PXE OpROM Boot Option Priorities These are settings for boot priority Specify the boot device priority sequence from the available devices Hard Drive BBS Priorities This item is for configuring the boot order for a specific device class lts option s is only visible if at least one device for this class is detected BIOS Setup Utility 53 eBOX671 885 FL Series User s Manual 45 Security Menu The Security menu allovvs users to change the security settings for the system Ap
11. socket contacts to avoid damage and do not touch processor sensitive contacts at any time during installation Caution Step 6 Thermal pad installation e Please confirm the processor has placed into CPU socket properly e Take one of processor thermal pad from accessory package e Paste the thermal pad on the processor with caution then remove protection film e Lock load lever to fix processor Hardware Installation 13 eBOX671 885 FL Series User s Manual Step 7 Fasten four screws to assemble top heatsink with main chassis 14 Hardware Installation eBOX671 885 FL Series User s Manual 2 2 Installing the SO DIMM Step 1 Turn off the system and unplug the power cord Step 2 There are four screws on the top heatsink are used to fasten the heatsink to the chassis Step 3 Loosen these screws to remove the top heatsink then you can find dual SO DIMM sockets on main board sBC87885 Ww ei d CE Rens Step 4 Locate the memory module insert the gold colored contact into the socket and push the module down until it is firmly seated by locking two latches on the sides ODPM 1600 SO DIMM Sy PIN CMAS 4GAOTEA WO A so UH Hardware Installation 15 eBOX671 885 FL Series User s Manual Step 5 Assemble top heatsink with chassis through four screws carefully to complete SO DIMM installation 16 Hardware Installation eBOX671 885 FL Series User s Manual 2 3 Installing the 2 5 SATA D
12. 4 4out as default for standard version you can get the pin define from below table 30 Jumper Setting amp Connector eBOX671 885 FL Series User s Manual 3 3 11 Isolated Digital VO Connector Option eBOX671 885 FL also equipped one version that supports isolated COM 8 channel digital I O to instead of 8 channel programmable digital VO Therefore please refer to the following information if your system belongs to isolated digital I O version of eBOX671 885 FL The digital I O can be configured to control cash drawers and sense warning signals from an Uninterrupted Power System UPS or perform store security control You may use software programming to control these digital signals m wo ENS e w e Dry Contact Wiring Wet Contact Wiring Jumper Setting amp Connector 31 eBOX671 885 FL Series Users Manual DO Contact Wiring a WO LOX O a E 3 3 12 ATX Power On OFF Button The ATX power button is on the I O side It can allow users to control eBOX671 885 FL power on off Function Description i AN d Turn on off system Keep system status 3 3 13 Reset Button The Reset button can allovv users to reset eBOX671 885 FL Reset Reset system a O Keep system status 3 3 14 Remote Power Switch Connector SPWRBT1 One 2 pin connector output for remote power on off switch Function Description Short 1 2 Turn on off system Open Keep system
13. AN6 The RJ 45 connector is for Ethernet Intel i211 AT To connect the board to a 1000 100 10 Base T hub just plug one end of the cable into connector and connect the other end phone jack to a 1000 100 10 Base T hub LAN 3 to LAN 6 all are PoE ports for standard of eBOX671 885 FL total watt maxmum up to 30 watt 4 CH PoE Compliant 4ports full load IEEE802 3af Class 2 7VVatt 2ports full load IEEE802 3af Class 3 15 4Wait 1ports full load IEEE802 3at Class 4 30Watit Pin LAN Signal pn LAN Signal d d JUL ta mon Lulu Activity link LED Yellow OFF No link Blinking Link established data activity detected Speed LED OFF 10Mbps data rate Green 100Mbps data rate Orange 1GMbps data rate Jumper Setting Connector 29 eBOX671 885 FL Series User s Manual 3 3 8 USB 2 0 Connector The Universal Serial Bus connectors are compliant with USB 2 0 480Mbps and ideally for installing USB peripherals such as keyboard mouse scanner etc Signal USB PortO0 Pi Signal USB Port 1 USB VCC USB VCC 5V level 5V level USB 40 D USB 1_D USB 0 D USB 1_D Ground GND Ground GND 3 3 9 Audio Connector These two audio jacks ideal are for Audio Mic In and Audio Line out pin am ON 2 Microphone In SH 3 3 10 Digital NO Connector eBOX671 885 FL supports 8 channel TTL digital I O programmable m
14. Section DC in Phoenix Power Connector 33 2 333 DVI I 3 3 4 Serial Port Connector E 33 6 337 USB 2 0 Connector 3 3 8 Audio Connector 3 3 9 3 3 10 Isolated Digital VO connector Option 3 3 11 ATX Power On Off Button 3 3 12 Rest Button 90 19 3 3 15 CFast Socket 3 3 16 Serial ATA SATA Connector SATA Power Connector 3 3 19 Full Size Express Mini Card slot SCN2 amp SCN3 3 3 20 Jumper Setting amp Connector 25 eBOX671 885 FL Series User s Manual 3 3 1 DC in Phoenix Power Connector The system supports 24V Phoenix DC in connector for system power input 3 3 2 HDMI Connector The HDMI High Definition Multimedia Interface is a compact digital interface which is capable of transmitting high definition video and high resolution audio over a single cable A H HA Y P Fi He lz AN M AR Ni lo Loan zt Le Homoursoa O Lem E EE o rowouroarao 19 nomira so womourcioces LI 26 Jumper Setting amp Connector eBOX671 885 FL Series User s Manual 3 3 3 DisplayPort Connector DisplayPort interface is also called DP port DPB LANEOH Detect Pin ls Poretaners 16 fono la len Las ln ls Losse 19 ono 3 3 4 DVI I Connector DVI I integrated combines digital and analog in the same connector digital may be single or dual link provides transmission of fast and high quality digital video between source device graphic card and display device Signal Dl DAT
15. VO address is 3E8h and for interrupt request line is IRQ7 46 BIOS Setup Utility eBOX671 885 FL Series User s Manual e Serial Port 4 Configuration serial Port Enabled E SL K LE FA Save 8 E 2 n ESC Exit Serial Port Use this item to enable or disable serial port 4 The optimal setting for base I O address is 2E8h and for interrupt request line is IRQ6 BIOS Setup Utility 47 eBOX671 885 FL Series User s Manual e NCT6106D HW Monitor Users can base on this page to get detail hardware monitor information F4 Save 2 Exit ESC Exit e Intel 1211 Gigabit Network Connection setting Porti to Port 6 NIC Configuration Intel R PRO 1000 5 5 23 FFFFFF DFF Intel 1211 1539 03 00 00 Disconnected 00 60 E60 52 82 E3 General Help Previous Values Optimized Defaults Save 8 Exit Port Configuration Menu User s can get LAN detail connection information by this page NIC Configuration Default is auto but we also can adjust to 10 half full Mbps or 100 hat full Mbps by different requirement 48 BIOS Setup Utility eBOX671 885 FL Series User s Manual 43 Chipset Menu The Chipset menu allows users to change the advanced chipset settings You can select any of the items in the left frame of the screen to go to the sub menus gt PCH IO Configuration gt System Agent SA Configuration For items marked with gt please press lt Enter gt for more opt
16. act your Axiomtek distributor for recycling and we will make the proper arrangement Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Pentium are registered trademarks of Intel Corporation MS DOS Microsoft C and QuickBasic are trademarks of Microsoft Corporation Windows 8 1 Windows 8 Windows 7 Windows XPE Windows XP Windows CE embedded Linux MS DOS Microsoft C and Other brand names and trademarks are the properties and registered brands of their respective owners vi Table of Contents o li Safely UNS A o oo ae ili A FP e iv General Cleaning TipS ccsscccesseccesseceeseecenseeenseeeeneesonseeeensesonseseensesonsesoensesonneses V Scrap Computer REGYGIIMI casino vi CHAPTER 1 INTRODUCTION aaa aannnn nenen nene neeeeeee eee RERE RR RR nn nn ene ee bebe ce ee ee 1 1 1 General Description nanen see sos e rene eren s eren n sere nene nese rene re neser ene rene seen 1 1 2 System Specifications siii ishe die nnmnnn 3 E PU DEE 3 Tea e E EEN 3 1 2 3 System Specification EE 4 TD Driver BB COMON so 4 1 3 DIMENSIONS E 5 Lt System EEN 5 1 3 2 Wall mount Bracket DIMENSION unnnaunnnnnn nanen anesore near esse rene e esen sme rene eren e eres e ee nnne 6 1 5 Sei inte EIS bone 9 1 6 MOJO ocn et oie 9 CHAPTER 2 HARDWARE INSTALLATION oocccccccnnnnnnninnnnnonooooooosooooommmm1111111
17. ally sets all Setup options to a complete set of default settings when you select this option Select Restore Defaults from the Save Exit menu and press lt Enter gt Save as User Defaults Select this option to save system configuration changes done so far as User Defaults Select Save as User Defaults from the Save amp Exit menu and press lt Enter gt Restore User Defaults It automatically sets all Setup options to a complete set of User Defaults when you select this option Select Restore User Defaults from the Save 8 Exit menu and press lt Enter gt Boot Override Select a drive to immediately boot that device regardless of the current boot order Launch EFI Shell from filesystem device Attempt to launch EFI Shell application Shellx64 efi from one of the available filesystem devices 56 BIOS Setup Utility eBOX671 885 FL Series User s Manual This page is intentionally left blank BIOS Setup Utility 57 eBOX671 885 FL Series Users Manual APPENDIX A WATCHDOG TIMER About VVatchdog Timer Software stability is major issue in most application Some embedded systems are not watched by human for 24 hours It is usually too slow to wait for someone to reboot when computer hangs The systems need to be able to reset automatically when things go wrong The watchdog timer gives us solution The vvatchdog timer is a counter that triggers a system reset when it counts down to zero from a preset value The software start
18. cloth is the best tool to use when rubbing up a component Although paper towels or tissues can be used on most hardware as well we still recommend you to rub it with a piece of cloth e Water or rubbing alcohol You may moisten a piece of cloth a bit with some water or rubbing alcohol and rub it on the computer Unknown solvents may be harmful to the plastics parts e Vacuum cleaner Absorb the dust dirt hair cigarette particles and other particles out of a computer can be one of the best methods of cleaning a computer Over time these items can restrict the airflow in a computer and cause circuitry to corrode e Cotton swabs Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard mouse and other locations e Foam swabs Whenever possible it is better to use lint free swabs such as foam swabs Sy R Note We strongly recommended that you should shut down the system before you start to clean any single components Please follow the steps below Close all application programs Close operating software Turn off power switch Remove all device Pull out power cable ASI Scrap Computer Recycling If the computer equipments needs the maintenance or are beyond repair we strongly recommended that you should inform your Axiomtek distributor as soon as possible for the suitable solution For the computers that are no longer useful or no longer working well please cont
19. cription The eBOX671 885 FL is an embedded system that supports LGA1150 Socket 4 generation Intel Core 7 15 13 Celeron processor to support Windows 7 Windows 7 Embedded Windows 8 1 Windows 8 Embedded or Linux suitable for the most endurable operation It features fan less design with full feature I O self contained PoE controller features performance computing with Power over Ethernet extended product longevity and enhanced system dependability by built in Watchdog Timer e Features 4th generation Intel Core i7 i5 i3 Celeron processors by LGA1150 socket Intel Q87 PCH Supports dual channel DDR3 1333 1600 SO DIMM max up to 16 GB 4 CH GbE PoE Power over Ethernet IEEE 802 3at compliant Supports 6 USB 3 0 amp 2 USB 2 0 ports Supports 2 x RS 232 422 485 amp 2 x RS 232 Supports 2 x 10 100 1000Mbps Ethernet 8 CH Digital UO 4IN 8 40UT Programmable 8 CH Isolated Digital I O 4IN amp 40UT Option Two PCI Express Mini Card Slots w mSATA supported Watchdog timer One SIM slot w three antenna openings ot Se ol eg kr ma O DA OH Introduction 1 eBOX671 885 FL Series Users Manual e Reliable and Stable Design The eBOX671 885 FL adopts the advanced cooling system and supporting the CFast amp mSATA which makes it especially suitable for vibration environments eBOX671 885 FL also supports wall mount kit it s best for industrial automation digital signage and gaming application e Fle
20. evice Step 1 Turn off the system and unplug the power cord Step 2 Turn the system upside down to locate screws at the bottom loosen screws Step 3 Remove the bottom cover Step 4 You can get the SATA data cable and the SATA power cable please refer to the following photos to place the SATA hard drive on bottom cover Please notice the direction of connector for HDD Hardware Installation 17 eBOX671 885 FL Series User s Manual Step 6 Connect the SATA data cable and SATA povver cable to the connectors on the SATA drive 2 5 HDD SSD 2 5 HDD SSD 18 Hardware Installation eBOX671 885 FL Series User s Manual 2 4 Installing the Express Mini Card Step 1 Turn off the system and unplug the povver cord Step 2 Turn the system upside down to locate screws at the bottom loosen screws Step 3 Remove the bottom cover then find Mini Card location eBOX671 885 FL supports two full size Mini PCI Express slots both all support mSATA device Besides SCN3 also supports one onboard SIM slot I Step 4 Insert the Mini PCI Express module into the slot at a 45 degrees angle until the gold plated connector on the edge of the module completely disappears inside the slot Step 5 Push the module down and then secure it with mounting screws biox 03 14 39 9 Model TOBY L210 AO 870200 0808 000 Ay IMEI 352255000049305 CE 1588 Made in Austnea FCC IO KPYTOSYL2 iC 85554 TOBYL219 Step 6 A
21. ions gt PCH IO Configuration BIOS Setup Utility 49 eBOX671 885 FL Series User s Manual e PCH IO Configuration This screen shows memory information For items marked with please press lt Enter gt for more options gt PCH Azalia Configuration General Help 5 Previous Values o Optimized Defaults Save 8 Exit ESC Exit PCH Azalia Configuration This item controls detection of the Azalia device Azalia Enter Select A Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save 8 Exit ESC Exit 50 BIOS Setup Utility eBOX671 885 FL Series User s Manual e System Agent SA Configuration This screen provides function for specifying internal graphics controller and memory related parameters Enabled Select Screen ti Select Item Enter Select l Change Opt SN F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save 8 Exit ESC Exit e Graphics Configuration Change Opt General Help Previous Values Optimized Defaults Save amp Exit Primary IGFX Boot Display Select the video device which will be activated during POST Power On Self Test This has no effect if external graphics present Aperture Size Aperture Size is a video configuration option that determines the amount of system memory available for direct access by the graphics device BIOS Setup Utility 51 eBOX671 885 FL Series
22. is enabled Active Processor Cores Active the cores of processors default sets to All EIST Enhanced Intel SoeedStep Technology EIST is a power and thermal management technology developed by Intel eBOX671 885 FL sets to Enabled for default setting Turbo Mode In order to keep system in stable operating condition we suggest users set disable by default CPU Information Supported Supported Supported Supported Supported Supported Change Opt ES Supported General Help Supported Previous Values E Dptimized Defaults Li Data Cache Save 8 Exit Li Code Cache SES Cache L3 Cache 8192 kB BIOS Setup Utility 41 eBOX671 885 FL Series User s Manual e SATA Configuration In this Configuration menu you can see the currently installed hardware in the SATA ports During system boot up the BIOS automatically detects the presence of SATA devices SATA Controller s Unknown Empty Unknown Change Opt Fi General Help F2 Previous Values F3 Optimized Defaults F4 Save 8 Exit ESC Exit SATA Mode Selection Determine how SATA controller s operate Operation mode options are RAID Mode IDE Mode and AHCI Mode e USB Configuration This screen shows the USB version and its detail information en E F1 General AG s F2 Previous Values F3 Optimized Defaults F4 Save 8 Exit ESC Exit 42 BIOS Setup Utility eBOX671 885 FL Series User s Manual e NCT6106D Super IO Configuration
23. lay the setup sub screens The lt F4 gt key allows you to save any changes you have made and exit Setup Press the lt F4 gt key to save your changes BIOS Setup Utility 37 eBOX671 885 FL Series User s Manual 4 3 Main Menu The first time you enter the setup utility you will enter the Main setup screen You can always return to the Main setup screen by selecting the Main tab System Time Date can be set up as described below The Main BIOS setup screen is shown below system Date BIOS Information Display the auto detected BIOS information System Date Time Use this option to change the system time and date Highlight System Time or System Date using the lt Arrow gt keys Enter new values through the keyboard Press the lt Tab gt key or the lt Arrow gt keys to move between fields The date must be entered in MM DD YY format The time is entered in HH MM SS format Access Level Display the access level of current user 38 BIOS Setup Utility eBOX671 885 FL Series User s Manual 4 2 Advanced Menu The Advanced menu also allovvs users to set configuration of the CPU and other system devices You can select any of the items in the left frame of the screen to go to the sub menus ACPI Settings CPU Configuration SATA Configuration USB Configuration NCT6106D Super IO Configuration NCT6106D HW Monitor Intel 1211 Gigabit Network Connections VVYVVVYVVYVVV For items marked with gt please press
24. mmary Proper jumper settings configure the eBOX671 885 FL to meet your application purpose We are herewith listing a summary table of all jumpers and default settings for onboard devices respectively Jumper __Function DefaultSetting Jumper Setting mSATA PCle Selection SCN2 3 5 Short SCN3 4 6 Short Restore BIOS Optimal Defaults or Sg Default Normal Operation seng ort Y Note How to setup Jumpers The illustration shows how to set up jumpers When the jumper cap is placed on pins the jumper is close if not that means the jumper is open e e Open Closed Pin1 2 Closed 3 2 1 Mini Card Selection JP2 Select mSATA or PCI Express x1 function on both two PCI Express Mini Card sockets Function aen SCN3 mSATA 1 3 Short 2 4 Short A a PCI E USB 3 5 Short 4 6 Short 5 e 3 2 2 Restore BIOS Optimal Defaults JP3 Put jumper clip to pin 2 3 for a few seconds then move it back to pin 1 2 Doing this procedure can restore BIOS optimal defaults Function Setting Normal Default EN Ss 2 3 24 Jumper Setting amp Connector eBOX671 885 FL Series User s Manual 3 3 Connectors Connectors connect the board with other parts of the system Loose or improper connection might cause problems Make sure all connectors are properly and firmly connected Here is a summary table shows you all connectors and button on the eBOX671 885 FL Series eternal connectors
25. nd press lt Enter gt Select Yes to save changes and exit Discard Changes and Exit Select this option to quit Setup vvithout making any permanent changes to the system configuration and return to Main Menu Select Discard Changes and Exit from the Save Exit menu and press lt Enter gt Select Yes to discard changes and exit Save Changes and Reset When you have completed the system configuration changes select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect Select Save Changes and Reset from the Save Exit menu and press lt Enter gt Select Yes to save changes and reset Discard Changes and Reset Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer Select Discard Changes and Reset from the Save 8 Exit menu and press lt Enter gt Select Yes to discard changes and reset BIOS Setup Utility 55 eBOX671 885 FL Series Users Manual Save Changes VVhen you have completed the system configuration changes select this option to save changes Select Save Changes from the Save Exit menu and press lt Enter gt Select Yes to save changes Discard Changes Select this option to quit Setup without making any permanent changes to the system configuration Select Discard Changes from the Save Exit menu and press lt Enter gt Select Yes to discard changes Restore Defaults It automatic
26. or Step 1 Turn off the system and unplug the power cord Step 2 There are four screws on the top heatsink are used to fasten the heatsink to the chassis Step 3 Loosen these screws to remove the top heatsink BC87885 T A A REV A0 RC CE oz Hardware Installation 11 eBOX671 885 FL Series User s Manual Step4 Remove the vvarning label and disengage load lever e Disengage load lever by releasing down and out on the hook e Rotate load lever to open position at approximately 135 e Rotate load plate to open position at approximately 150 Ka Apply pressure to corner with right hand thumb when opening or closing load lever otherwise lever will bounce back as a mouse trap Note causing bent contacts Step 5 Processor installation e Lift processor package from shipping media by grasping the substrate edges e Scan the processor package gold pads for any presence of foreign material e Locate connection 1 indicator on the processor which aligns with connection 1 indicator chamfer on the socket and notice processor keying features that line up with posts along socket walls e Grasp the processor with thumb and index finger along the top and bottom edges The socket will have cutouts for your fingers to fit into e Carefully place the processor into the socket body vertically 12 Hardware Installation eBOX671 885 FL Series User s Manual E e a AE Connector 1 Indicator E Never touch fragile
27. package m 5 1 kg 11 24 Ib with package Dimensions 280mm 11 02 VV x210mm 8 27 D x 76mm 2 99 H 2 4 Driver CD Content Driver E Audio E Chipset E Ethernet m Graphic a Intel Rapid Storage Technology D USB 3 0 E ME 9 0 Manual E User Manual E Quick Manual YY Note All specifications and images are subject to change without notice Introduction eBOX671 885 FL Series User s Manual 1 3 Dimensions The following diagrams show you dimensions and outlines of the eBOX671 885 FL 1 3 1 System Dimension TE Introduction 5 eBOX671 885 FL Series Users Manual 1 3 2 Wall mount Bracket Dimension Go Ge Eje om Hp a 5 le ay a o St eg D Introduction eBOX671 885 FL Series User s Manual 1 4 DO Outlets The following figures show you l O outlets on front view of the eBOX671 885 FL e Front View drawing CFast 4 AT ATX Switch Power Reset Audio USE 3 0 4 CH PoE HUOT A h CIFIC IC ett e ja Li Li E HDD Remote 2 x GbE Indicator PWR Switch AMAMAA 4 Introduction eBOX671 885 FL Series User s Manual e Rear View drawing USB2 0 USE 3 0 HDMI DYI I R5 232 R5 232 422 4185 IL DNH ODC il OE ES aaa e SCH S LL Ee CH ME l cz l E J EA I D el DisplayPort 2IVDI SCH Power input Digital 1 0 V eBOX671 885 FL DC H gt ANT z FR Bio be oe O 4 0 AALAAAA eBOX671 885 FL DC
28. r use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide 4 Mode of operation Continuous General Cleaning Tips You may need the follovving precautions before you begin to clean the computer VVhen you clean any single part or component for the computer please read and understand the details below fully When you need to clean the device please rub it with a piece of dry cloth 1 Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor 2 Turn the system off before you start to clean up the component or computer 3 Never drop the components inside the computer or get circuit board damp or wet 4 Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of cleaning Some individuals may be allergic to the ingredients 5 Try not to put any food drink or cigarette around the computer Cleaning Tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals Keep in mind that some components in your computer may only be able to be cleaned using a product designed for cleaning that component if this is the case it will be mentioned in the cleaning e Cloth A piece of
29. re sensitive to static electrical charge Disconnect the power cord from the eBOX671 885 FL before making any installation Be sure both the system and the external devices are turned OFF Sudden surge of power could ruin sensitive components Make sure the eBOX671 885 FL is properly grounded Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Turn OFF the system power before cleaning Clean the system using a cloth only Do not spray any liquid cleaner directly onto the screen Do not leave this equipment in an uncontrolled environment where the storage temperature is below 40 C or above 80 It may damage the equipment Do not open the systems back cover If opening the cover for maintenance is a must only a trained technician is allovved to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the follovving precautions e Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body e When handling boards and components wear a wrist grounding strap available from most electronic component stores Classification 1 Degree of production against electric shock not classified 2 Degree of protection against the ingress of water IP40 3 Equipment not suitable fo
30. s counter with an initial value and must reset it periodically If the counter ever reaches zero which means the software has crashed the system will reboot 58 Watchdog Timer Setting eBOX671 885 FL Series User s Manual Sample Program The following example enables configuration using debug tool Enable WDT y Enable configuration O 2E 87 5 Un lock super I O O 2E 87 y Select logic device O 2E 07 O 2F 08 y WDT device enable O 2E 30 O 2F 01 y Set timer unit O 2E FO O 2F 00 00 Sec 08 Minute y Set base timer O 2E F1 O 2F OA Set reset time where 0A hex 10sec Disable WDT y Enable configuration O 2E 87 Un lock super I O O 2E 87 y Select logic device O 2E 07 O 2F 08 y VVDT device disable O 2E 30 O 2F 00 Watchdog Timer Setting 59 eBOX671 885 FL Series Users Manual This page is intentionally left blank 60 VVatchdog Timer Setting
31. ssembly the bottom Cover back and fasten all screws Hardware Installation 19 eBOX671 885 FL Series User s Manual 2 5 Installing the CFast Card Step 1 Turn off the system and unplug the power cord Step 2 Remove the mounting screws of the CompactFlash socket s cover Step 4 Close the cover to the chassis and fasten two screws to complete installation per m mi EH np Reset N 4 e wen Ped Pewee G ft W I j j 20 Hardware Installation eBOX671 885 FL Series User s Manual This page is intentionally left blank Hardware Installation 21 eBOX671 885 FL Series User s Manual CHAPTER 3 JUMPER SETTING 8 CONNECTOR Proper jumper settings configure the eBOX671 885 FL to meet your application purpose We are herewith listing a summary table of all jumpers and default settings for onboard devices respectively 3 1 Jumper 8 Connector Location SBC87885 Top Side 22 Jumper Setting Connector eBOX671 885 FL Series User s Manual SBC87885 Bottom Side cN19 ICN17 ood oba ao sl Sa O 3 OOo polo cog coo O O o O O O O o O O o boo end CNA pa CN3 4 Y N Note We strongly recommended that you should not modify any unmentioned jumper setting without Axiomtek FAE s instruction Any modification without instruction might cause system to become damage Jumper Setting Connector 23 eBOX671 885 FL Series Users Manual 3 2 Jumper Setting Su
32. status 32 Jumper Setting amp Connector eBOX671 885 FL Series User s Manual 3 3 15 AT ATX Switch You can adjust this switch once you remove CFast cover If you set AT ATX switch to AT mode the system will be automatically power on without pressing soft power button during power input we can use this switch to achieve auto power on demand AT 7 ATX 3 3 16 CFast Socket The system is equipped with a CFast socket on the bottom side to support a CFast card which is based on the Serial ATA bus The socket is specially designed to avoid incorrect installation of the CFast card When installing or removing the CFast card please make sure the system power is off The CFast card by default identifies itself as C or D drive in your PC system ano Pc 202 er ro NO PC11 NG PC12 NG PC13 3 3V PC14 3 3V PC15 GND PC16 GND PC17 NC Jumper Setting Connector 33 eBOX671 885 FL Series User s Manual 3 3 17 SATA Connector SATA 1 8 2 These Serial Advanced Technology Attachment Serial ATA or SATA connectors are for high speed SATA interfaces They are computer bus interfaces for connecting to devices such as hard disk drives This board has two SATA 3 0 ports with 6Gb s performance Drin siora 0000000 L e SATA_RX GND 3 3 18 SATA Power Connector Use CN8 CN9 for interfacing to SATA 2 5 HDD power supply Pin signal e y ee pol 12V level O is Ke gt
33. tio Setup Utility Copyright C 2012 American Megatrends Inc Main Advanced Chipset Boot Save Exit Administrator Password Version 2 15 1226 Copyright C 2012 American Megatrends Inc Administrator Password This item indicates whether an administrator password has been set installed or uninstalled User Password This item indicates whether an user password has been set installed or uninstalled 54 BIOS Setup Utility eBOX671 885 FL Series User s Manual 4 6 Save 8 Exit Menu The Save Exit menu allows users to load your system configuration with optimal or fail safe default values Aptio Setup Utility Copyright C 2012 American Megatrends Inc G KI E e SA Save amp Exit Exit system setup after saving Discard Changes and Exit the changes Save Changes and Reset Discard Changes and Reset Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Select Screen 1 Select Item Enter Select Change Opt Fl General Help F2 Previous Values F3 Optimized Defaults F4 Save Exit ESC Exit Boot Override SATA PM ST3160316AS Launch EFI Shell from filesystem device Version 2 15 1226 Copyright C 2012 American Megatrends Inc Save Changes and Exit VVhen you have completed the system configuration changes select this option to leave Setup and return to Main Menu Select Save Changes and Exit from the Save 8 Exit menu a
34. urn on the computer and press the lt Del gt key immediately 2 After you press the lt Del gt key the main BIOS setup menu displays You can access the other setup screens from the main BIOS setup menu such as the Advanced and Chipset menus It is strongly recommended that you should avoid changing the chipset s defaults Both AMI and your system manufacturer have carefully set up these defaults that provide the best performance and reliability 4 2 Navigation Keys The BIOS setup utility uses a key based navigation system called hot keys Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process These keys include lt F1 gt lt F2 gt lt Enter gt lt ESC gt lt Arrow gt keys and so on Y SN Note Some of the navigation keys differ from one screen to another gt lt Left Right The Left and Right lt Arrow gt keys allow you to select a setup screen AN Up Down The Up and Down lt Arrow gt keys allow you to select a setup screen or sub screen The Plus and Minus lt Arrow gt keys allow you to change the field value of a Plus Minus particular setup item The lt Esc gt key allows you to discard any changes you have made and exit the Setup Press the lt Esc gt key to exit the setup without saving your changes The lt Enter gt key allows you to display or change the setup option listed for a particular setup item The lt Enter gt key can also allow you to disp
35. xible Connectivity eBOX671 885 FL features four Power over Ethernet PoE Gigabit Ethernet ports for connecting to GigE Vision cameras and four USB 3 0 ports for connecting to USB3 Vision cameras Additionally two more Gigabit Ethernet ports allow for networks communication eBOX671 885 FL also supports two RS232 RS485 amp 2 RS 232 serial interfaces and 8 channel digital VO e Embedded O S Supported The eBOX671 885 FL not only supports Windows 7 Windows 8 1 but also supports embedded OS such as Windows 7 Embedded Windows 8 Embedded and Linux e Various Storage Supported For storage device the eBOX671 885 FL supports two 2 5 SATA storage drive bay one CFast slot and mSATA devices 2 Introduction eBOX671 885 FL Series User s Manual 1 2 System Specifications 1 2 1 CPU CPU H LGA1150 Socket Intel Core i7 i5 i3 Celeron processor Chipset e Intel Haswell Haswell refresh Q87 chipset BIOS American Megatrends Inc UEFI Unified Extensible Firmware Interface BIOS System Memory m Two 204 pin unbuffered DDR3 1333 1600 MHz SO DIMM socket max up to 16GB 2 2 lO System Display mintel HD Graphics by CPU max up to triple independent display m One HDMI Supports HDMI 1 4a max resolution up to 4096 x 2160 24Hz One DVI I connector Supports max resolution up to 1920x1200 60Hz One DisplayPort Supports max resolution up to 3840x2160 60Hz Audio m One Audio connector Mic in Line out Ethernet
Download Pdf Manuals
Related Search