ELECTRICAL SALAMANDER
Contents
1. MELLO ELECTRICAL SALAMANDER METOS MARINE OS200 440V3PE 60HZ 4159913 INSTALLATION AND OPERATING MANUAL TABLE OF CONTENTS COVER PAGE MEN a resus orcowenrs 3 inrooucnon o 4 SSS O 3 RECTROALORCUT DIAGRAM MAIN DIMENSIONS TMMSPORTNGANDMOWNG 9 INSTALLATION OF THEAPPLANGE w ver OPERATION OFTHEAPPLIANGE 13 CLEAWUPANDMANTENANCE a remus oFwanmanty IN caution This appliance should only be used in facilities where relevant standards laws anc safety requirements are complied with 2 14 INTRODUCTION Dear User Thank vou for purchasing our appliance and for vour reliance upon our companv Our appliances are used in professional kitchens in 75 countries Our appliances are produced in compliance with international standards Important notice Please read and ensure that the users read this user s manual in order to achieve the desired performance in line with vour expectations and to use vour appliance for long vears Please take the warnings mentioned above into consideration before calling for service Please read and ensure that your operation personnel also reads this user s manual care fully before installing and using the appliance If the appliance is operated without reading the user s manual the appliance will not be covered by the warranty The manual containing information about installation usage and maintenance of our produc2. after clean up 2 MAINTENANCE Periodic maintenance should be carried out by a technician It is recommended to carry out maintenance at least every 6 months depending on the frequency of use Periodic maintenance conducted by authorized service personnel of ours is charged even the guarantee period has not expired LIFE OF USE Appliances life of use is 10 year if it is used under recommended conditions 13 14 metos kitchen intelligence
3. an power Do not hit or drop the device when moving 8 14 INSTALLATION OF THE APPLIANCE ee If this appliance located near to any wall separation kitchen furniture decorative coating etc the distance in between should be min 20 cm and if those are coated with fireproof heat insulating material the distance should be min 5 cm It is strongly recommended that fire safety protection instructions are observed All of the items mentioned below in connection with the installation of the appliance should be carried out by authorized service personnel Workbench on which the device stands should be adjustable and the device should be ensured to operate in a leveled position 3 Power supply connection of the appliance should be checked by an eligible electrician and it should be connected to a fuse at a maximum height of 170 cm Power supply connection should be made using a 30 mA current leakage fuse as a protection against current leakage danger is Power installation of the appliance should be grounded by connecting it to a grounding bar at the nearest panel 9 14 CONTROL BOARDS A POWER REGULATOR SWITCH B appliance ON LAMP 10 14 OPERATION OF THE APPLIANCE 1 Salamander is used in kitchens of restaurants fast food stands canteens hospitals in order to frv grill or roasting of food 2 Before initial use of the appl ance the outer surface should be wiped with a cloth soaked in warm
4. cting it from the power supply EF It is recommended to operate the appliance between temperatures of 5 C 40 C and in ambient humidity of maximum 65 11 14 OPERATION OF THE APPLIANCE CAUTIONI The appliances should be installed and operated as described in this user s manual If any failure is encountered please contact our nearest authorized service dealer WHEN THE APPLIANCES HAS A FAILURE ONLV AUTHORIZED SERVICE DEALERS ARE ALLOWED TO HANDLE THE APPLIANCES IF ANY PERSON OTHER THAN ONLY AUTHORIZED SERVICE DEALERS HANDLE THE APPLIANCES IT WILL NOT BE COVERED BY THE WARRANTY NEVER ALLOW PEOPLE WHO ARE NOT AUTHORIZED TO HANDLE THE APPLIANCES OTHERWISE PRODUCER COMPANY WILL NOT BE RESPONSIBLE FOR THE CONSEQUENCES DURING MAINTENANCE SERVICE OUR AUTHORIZED SERVICE DEALERS SHOULD NOT BE PROPOSED TO USE NON ORIGINAL SPARE PARTS FOR WHATSOEVER INSTALLING ANY NON ORIGINAL SPARE PART TO THE APPLIANCE LEAVES THE APPLIANCE OUT OF WARRANTY COVERAGE S 12 14 CLEAN UP AND MAINTENANCE 1 CLEAN UP Before before the power is switched on and after the first use and every subsequent use outer surface of the appl ance should be completely cleaned up with sponge and liquid detergent and then wiped dry Do not use CHEMICAL CLEANING AGENTS like hydrochloric acid or abrasive cleaning agents When oil pan is used the device should be cleaned up and dried after daily use Device should not be left wet
5. s 440V 3PE 60Hz 6 14 SAFETV DETAILS he appliance should only be operated under a chimney hood c Any kind of flammable solid and liquid material cloths alcohol and derivatives petrochemical products wooden and plastic materials cutting blocks curtains etc should never be held near the appliance c You can use this appliance simultaneously together with other products of ours c Do not clean up the appliance with pressure water his appliance should be installed in line with effective regulations and only be operated in well ventilated places Please refer to the instructions before installing and operating the appliance c This appliance is designed for industrial use and should only be operated by personnel trained on the appliance he appliance should not be handled by unauthorized persons except for the manufacturer or authorized service n case of fire or flame in the area where the appliance is operated act without panic close gas valves turn off the power switches and use a fire extinguisher Never use water to extinguish the fire 7 14 TRANSPORTING AND MOVING zz MAN CHANGING THE LOCATION Machines installed bv an authorized service CANNOT BE MOVED ELSEWHERE ITS POWER SUPPLV CABLES CANNOT BE EXTENDED OR REPLACED except bv an authorized service Before transporting device should be disconnected from power The device can be moved with m
6. t you purchased should be read carefully Please ensure that power supply connections to the appliance are already installed by qualified personnel according to local legislation before our authorized service personnel arrives for the installation of the appliance gt If you are confused or you don t have enough information please get in touch with authorized service by phone Please keep in mind that if the service personnel is delayed at your site related expenses and delay costs will be charged to you on hourly basis We hope that you will get the best performance from our product 3 14 TECHNICAL DATA VOUR PRODUCT S TYPE OS 200 MAIN DIMENSIONS mm 600 X 580 X 580 TOTAL ELECTRICAL INPUT kW POWER SUPPLY VOLTAGE V WORKING FREQUENCY Hz SUPPLY CABLE HO7 RNF MAXIMUM SLOPE PROTECTION CLASS NET WEIGHT Kg 4 14 ELECTRICAL CIRCUIT DIAGRAM L1 L2 L3 7 ER1 ER2 P1 P2 P1 P2 R QH L w o Neutral 4550 W 5000 W E X H1 l u 400V 4407 2275 W 2500W 2275 W 2500 W 400 V 440 V 400 V 440 V ER1 ER2 Energy regulator 11 12 Green indicator 440V H1 H2 Heating element 2500W 440V MAIN DIMENSIONS 5 14 WARNING SIGNS PE l POWER NETWORK GROUNDING GROUNDING OVERHEAT Power supply connection
7. water and soap NOTE Do not use except purpose of use The appl ance should be operated by qualified personnel knowing safety terms and technical specifications and who has read the instruction manual CAUTION NEVER OPERATE VOUR appl ance WITHOUT GROUND CONNECTION the device carefully out of its package Zs Set the skip level appropriately If Turn the starter switch step bv step to set relevant operating temperature Green lamp 3n 2 smell a fume and odor during first ever operation of the appl ance This smell will due to the first operation of the appl ance and will diminish after a while The heaters are located in the top moving component This top component moves up and down very easily Its height is adjustable Food to be fried should be placed on the grill Food to be cooked on tray should be placed on oil pan Frying time varies depending on the type of the food material Dishes or travs to be used for serving fried foods should stand up to maximum 300 C Dishes and travs that could melt should not placed into the device AG RG After frying is completed dishes or trays should be handled with hand gloves when taking them out z Oil or residuals accumulated in the oil pan due to oil usage should be cleaned otherwise they may be infected gt Turn the commutator to 0 position after daily use Disconnect the appliance from the power supply Clean up the appliance after disconne
Download Pdf Manuals
Related Search